INDOOR CLIMATE SOLUTIONS PRODUCT CATALOG Uponor Radiant Heating/Cooling

INDOOR CLIMATE SOLUTIONS PRODUCT CATALOG 2012 Uponor Radiant Heating/Cooling

Uponor Radiant Heating/Cooling > List of content List of content Abbreviations 4 Uponor Renovationsystem Minitec Uponor Minitec - System components and accessories 8 Uponor lightweight panel Siccus Uponor Siccus - System components and accessories 11 Uponor pipe positioning panel Tecto Uponor Tecto - System components and accessories 14 Uponor self attaching system Uponor self attaching system - System components and accessories 19 Uponor stapler and clamp track Uponor stapler and clamp track - System components and accessories 22 Uponor pipe positioning panel Uponor pipe positioning panel - System components and accessories 27 Uponor steel mesh Classic Uponor Classic - System components and accessories 32 Uponor Plaster Ceiling Cooling Uponor Plaster Wall/Ceiling H/C - System components and accessories 35 Uponor heat emission plate 38 Uponor underfloor heating accessories Uponor underfloor heating accessories 39 Uponor underfloor heating manifolds Uponor modular plastic manifolds 42 Uponor accessories for plastic manifolds 43 Uponor stainless steel manifolds 45 Uponor manifold accessories 46 Uponor pipe bend support 48 Uponor manifold cabinets 48 EEI-Int-RHC-01.12 3

Uponor Radiant Heating/Cooling > Abbreviations Abbreviations Shortcut unit Description A/F [mm] across flats A [m²] square measure c/c [mm] centre - centre distance c/c1 [mm] centre - centre distance 1 colour [-] colour Con. [l/m²] consumption d [mm] diameter d1 [mm] diameter 1 d2 [mm] diameter 2 d3 [mm] diameter 3 di [mm] diameter inside DN [mm] diameter nominal DT [d] drying time in days EP/a [W] effective power per actuator FT ["] female thread FT m [-] female thread (metric) G [kn/m²] load bearing capacity h [mm] height h1 [mm] height 1 h2 [mm] height 2 l [mm] length l [m] length in meter l1 [mm] length 1 MT ["] male thread outlets [-] Number of outlets OV [V] operating voltage p [bar] pressure P [W] effective power Q [kw] nominal power r [mm] radius R-value [m²k/w] thermal resistance s [mm] strength / wall thickness sd [mm] side distance stroke [mm] stroke Type [-] Type V [l/m] volume w [mm] width w [m] width in meter w1 [mm] width 1 w2 [mm] width 2 z [mm] z-value Δ Lw [db] impact noise improvement 4 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > List of content List of content Uponor controls Uponor Radio control 50 Uponor outdoor sensor 54 Uponor wired control 55 Uponor control accessories 24 V 59 Uponor wired control 230 V 60 Uponor control accessories 230 V 61 Uponor climate controller 63 Uponor control stations 67 Uponor industrial underfloor heating Uponor industrial floor heating PE-Xa pipes 71 Uponor PE-Xa Q&E fittings 72 Uponor industrial floor heating fixation and accessories 73 Uponor industrial floor heating manifold and accessories 75 Uponor snow and ice melting Uponor snow and ice melting pipes 77 Uponor snow and ice melting manifold and accessories 78 Uponor sport floor heating Uponor sport floor PE-Xa pipes 83 Uponor sport floor PE-Xa Q&E fittings 84 Uponor sport floor fixation and accessories 85 Uponor comfort panel Uponor comfort panel 88 Uponor comfort panel - accessories 90 Uponor gypsum panel Uponor gypsum panel 96 Uponor gypsum panel - accessories 97 Uponor tools Uponor tools 99 International sales and delivery terms 105 Item search register 107 How to contact us 111 EEI-Int-RHC-01.12 5

Radiant heating and cooling systems - for all areas of application the right system Radiant heating and cooling systems Minitec Siccus Tecto Self attaching system Minimum height, maximum comfort The lightweight for renovation For fast and accurate laying Micro interlocking for maximum holding force Floor Renovation x x Floor new build, SFH, MFH, public buildings x x x Wall/Ceiling - new build and renovation x Accessory systems Fittings UFH accessories Manifolds Cabinets For each pipe a save connection To have the right accessories is what matters Balanced distribution of heat into the last corner For surface and flush installation x x x x Special Applications Industrial UFH Snow & ice melting Sports floor heating Comfort panel Heating/Cooling of productions halls, warehouses or logistic centers Keeping areas snow & ice free Sports floor heating for surface elastic floors Ceiling cooling for suspended ceilings x x x x 6 EEI-Int-RHC-01.12

Stapler and clamp track Pipe positioning panel 14 16 Classic Plaster Wall/Ceiling Versatile through flexible pipe laying For fast and accurate laying Proven for years, precise laying Multifunctional for wall and ceiling x x x x x x Controls Control stations Tools 20,5 Wired or wireless controlled, sensitive and comfortable Energy efficient supply temperature control which makes the work easier x x x Ceiling cooling systems Gypsum panel Contec Contec ON Ceiling cooling for gypsum board ceilings The storable concrete core activation The highly efficient surface close building part activation x x x EEI-Int-RHC-01.12 7

Uponor Radiant Heating/Cooling > Uponor Renovationsystem Minitec Uponor renovationsystem Minitec Fast installation, short heat-up time: the Uponor renovationsystem Minitec offers you a range of advantages. The Uponor minitec foil element for the laying of the PE-Xa pipes measures 9.9 x 1.1 mm and can be installed on any existing screed, timber of tiled floor. Thanks to this small element height of around one centimetre, the system is particularly suitable for integration into existing buildings. Your advantages Ideal for retrofitting in existing buildings during renovations Suitable for direct installation on screed or tiled floors Elements height only 12 milimeter Low-cost installation of foil elements and pipe Foil elements can be walked over immediately after installation Short heat-up times Low heating water temperatures Can be connected directly to existing radiant heating systems System components System pipe/fittings Additional components Manifold/Cabinets Uponor high performance panel Uponor PE-Xa pipe 9,9 x 1,1 Uponor Minitec edging strip Uponor manifold Uponor PE-Xa Q&E coupling Uponor Minitec joint profile Uponor PE-Xa conversion nipple Uponor Minitec clamp track 9.9 Uponor manifold connection valve set G 1/Rp 1 Uponor pipe connection PE-Xa 9.9 Uponor Minitec joint protection Uponor cabinet Uponor PE-Xa Pipe 9.9x1.1 expander Room controls Control stations Uponor radio control Uponor wired control 24 V 230 V components Uponor control stations - overview 20,5 e.g. can be used with Knauf Levelling Screed 425 8 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor Renovationsystem Minitec Uponor Minitec - System components and accessories Uponor Minitec high-performance panel Designed as sturdy pipe fixing panel of minimum height, with integrated pipe laying channels for correct pipe laying distances; designed for Uponor Minitec PE-Xa pipes 9.9 x 1.1 mm; allowing for straight and diagonal pipe laying; with undercut, deep pipe fixing studs; overlap on both sides with triangular studs; perforated panel for installation between levelling compound and substructure; with self-adhesive back for proper fixture to screed and tiled floors Material: Polystyrene DIN 4102 building material class: B2 Pipe spacing: Vz 5, 10, 15 Colour: traffic black (near RAL 9017) Item no. h [mm] l [mm] w [mm] A [m²] Description unit Uponor Minitec high performance panel 1005261 12 1120 720 0.77 with,self-adhesive layer for pipes 9.9mm 15.4 m² Uponor PE-Xa pipes PE-Xa pipe with an oxygen diffusion barrier manufactured from peroxide cross-linked polyethylene (PE-Xa) using the Engel method complying with e.g. preniso 15875 Plastics piping systems for hot and cold water installations - Cross-linked polyethylene with an oxygen diffusion barrier of EVOH (ethyl vinyl alcohol). Uponor pipes fulfil the requirements for oxygen diffusion resistance as per DIN 4726. Malfunction temperature 95 C. Design pressure 8,8 bar (at 70 C). Item no. d [mm] s [mm] l [m] V [l/m] Description unit 1033024 9.9 1.1 120 0.047 Uponor eval PE-Xa pipe 9.9x1.1 120 m 1033025 9.9 1.1 480 0.047 Uponor eval PE-Xa pipe 9.9x1.1 480 m 1033026 9.9 1.1 240 0.047 Uponor eval PE-Xa pipe 9.9x1.1 240 m Uponor PE-Xa Q&E coupling 9.9 For Uponor PE-Xa pipe 9.9 x 1.1 mm, consisting of: - 1 coupling - 2 PEX Q&E rings for secure connection Material: Coupling made in brass; PEX Q&E rings made in high-pressure cross-linked polyethylene Item no. d [mm] s [mm] l [mm] z [mm] Description unit Uponor PE-Xa Q&E coupling 9.9-9.9 1005264 9.9 1.1 34 4 with two PEX rings 10 pcs Uponor PE-X ring for PE-Xa pipes For Uponor Minitec PE-Xa pipe 9.9 x 1.1 mm; to secure fixing to Minitec fittings Material: High-pressure cross-linked polyethylene (PE-Xa) Item no. d [mm] Description unit Uponor PE-X ring for PE-Xa pipes 1005263 9.9 9.9 x 1.1 10 pcs Uponor PE-Xa conversion nipple For Uponor PE-Xa pipes 9.9 x 1.1 mm, made of brass. Item no. d [mm] MT ["] l [mm] z [mm] A/F [mm] Description unit Uponor PE-Xa conversion nipple 1005265 9.9 R 1/2 39 14 22 9.9-1/2 with one PEX ring 10 pcs EEI-Int-RHC-01.12 9

Uponor Radiant Heating/Cooling > Uponor Renovationsystem Minitec Uponor Minitec - System components and accessories Uponor edging strip, 80x8 Edging strip for high performance panel conforming to DIN 18560, made of polyethylene with self-adhesive backing, self-adhesive strip on outer face provides tight seal between edging strip and insulation; Length of roll: 20 m Item no. h [mm] l1 [mm] s [mm] l [m] Description unit Uponor Minitec edging strip, 80 x 8 1005267 80 70 8 20 in length of 20 m 200 m Uponor joint profile 40x10 Self-adhesive clamp-on profile element for high performance panel made of hard PVC with polyethylene foam expansion strip, for the reliable separation of screed sections (e.g. in doorways), and to absorb expansion of screed. For expansion joints as per DIN 18560-2. Height: 40 mm Material thickness: 10 mm Length: 1,8 m Item no. l [mm] s [mm] w [mm] h [mm] Description unit Uponor Minitec joint profile 1005268 1800 10 50 40 40 x 10, length 1.8 m 18 m Uponor joint protection 9.9mm Made of PE-LD, with slit opening, for protection of pipes up to 9.9 mm in areas of expansion joints. Length: 300 mm b l s Item no. l [mm] s [mm] w [mm] Description unit Uponor joint protection tube for 1005269 300 2 35 PE-Xa pipes 9.9 x 1.1, length 300 mm 30 pcs d r a Uponor clamp track 9.9 Self-adhesive U-profile strip made of recycled material, with integrated pipe holder for 9.9 x 1.1 mm Uponor PE-Xa pipes. Length of track: 2.5 m Width of track: 24 mm Space between pipe holders: 20 mm c/c Installation height with pipe: 13 mm h l b Item no. l [mm] w [mm] h [mm] d [mm] c/c [mm] Description unit 1005274 2500 24 13 10 20 Uponor clamp track 9.9 mm 25 m 10 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor lightweight panel Siccus Uponor lightweight panel Siccus The Uponor lightweight panel Siccus has been specially designed as a universal solution for the restoration of old buildings where a low construction height and low weight are very important. The panels are installed on the floor below the load distribution layer consisting of dry screed panels or heating screeds. Your advantages Minimum floor construction height from 50 mm Short installation time, immediately accessible if installed with dry screed Low static weight from 25 kg/m² Last with dry screed panels Specially devised installation panel for universal use System components Systempipe/-Fittings Additional components Manifold/Cabinets Uponor Siccus lightweight panel PE-Xa pipe 14x2 Uponor edging strip Uponor manifold Uponor Siccus heat emission plate Uponor MLCP 14 pipe Uponor joint profile 100x10 Uponor compression adapter PE-Xa and MLCP Uponor PE Foil 0.2mm PE-type 200 Uponor PE-Xa Q&E coupling MLC press coupling 14x2 Uponor joint protection 20mm Uponor marking set Uponor manifold connection valve set G 1/Rp 1 Uponor screed additive Uponor cabinet Uponor PE foil 0.2 mm Room controls Control stations Uponor radio control Uponor wired control 24 V 230 V components Uponor control stations - overview 20,5 e.g. can be used with Knauf Brio Pre-fab Floor Screed Elements EEI-Int-RHC-01.12 11

Uponor Radiant Heating/Cooling > Uponor lightweight panel Siccus Uponor Siccus - System components and accessories Uponor Siccus lightweight panel Pipe fixing panel for butt joint installation; with pipe channels for the installation of heat emission plates or Uponor PE-Xa pipes 14 x 2 mm and Uponor MLCP pipes 14 mm Material: Expanded polystyrene rigid foam according to DIN EN 13163 DIN 4102 building material class: B1 Application type according to DIN 4108-10: DEO Compressive strength: = 150 kpa Technical data Plate size: 1197 x 1050 mm Plate thickness: 25 mm Thermal resistance: 0.622 m2 K/W Payload: 7.5 kn/m2 Pipe spacing: 15 cm, 22.5 cm or 30 cm Item no. l [mm] w [mm] h [mm] A [m²] Description unit 1005485 1197 1050 25 1.25 Uponor Siccus lightweight panel 12.5 m² l b Uponor heat emission plate 14 mm For installation on Uponor lightweight panel; ensures uniform heat distribution and proper fixture of Uponor PE-Xa pipes 14 x 2 mm and Uponor MLCP RED radiant heating pipes 14 x 1.6 mm; with double perforations for easy cutting to size. Material: Aluminium Plate size: 120 x 1180 mm Plate thickness: 0.45 mm Material requirement: Pipe spacing Va 15 = 5.6 plates/m2 Pipe spacing Va 22.5 = 3.7 plates/m2 Pipe spacing Va 30 = 2.8 plates/m2 Item no. l [mm] w [mm] Description unit Uponor Siccus heat emission plate 14 mm 1005486 1180 120 for lightweight panel, 1180 x 120 mm 48 pcs Uponor PE foil 0.2mm For installation on Uponor insulation or on standardised insulating material approved for the intended purpose for areas without stud foil. Prevents screed penetrating the underlying insulation. Dimensions: 4 m x 2.5 m Thickness: 0.2 mm Item no. l [m] w [m] s [mm] Description unit Uponor PE foil 0.2 mm thickness 1005049 60 1.25 ~0.2 60 x 1.25 m 75 m² Uponor PE-Xa pipe as coil, for use as radiant heating pipe, connected by Q&E, press or clamp fittings. Material: Uponor PE-Xa pipe made in high-pressure cross-linked polyethylene (Engel method), conforming to DIN 16892 and DIN ISO 15875, oxygen-tight according to DIN 4726 Colour: white with black and red longitudinal stripes Uponor PE-Xa pipe Max. operating temperature: 90 C Max. operating pressure: 6 bar at 70 C Application class: 4 / 6 bar Item no. d [mm] s [mm] l [m] Description unit Uponor eval PE-Xa Q&E pipe 14x2.0 1048290 14 2 240 240 m coil 240 m Uponor eval PE-Xa Q&E pipe 14x2.0 1048291 14 2 640 640 m coil 640 m 12 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor lightweight panel Siccus Uponor Siccus - System components and accessories Uponor MLCP white in coils Diffusion-tight multi-layer composite pipe (PE-RT - adhesive - longitudinally welded aluminium - adhesive - PE-RT) for distribution conduits, rising mains and connection lines for plumbing, radiator connection and fancoil connection. Fire classification E according to DIN EN 13501-1. Pipe end caps as hygienic seal according EN 806. Resistance of temperature: Tap water: The maximum permanent operating temperature exists between 0 C and 70 C at a maximum permanent operating pressure of 10 bars. The short-term malfunction temperature is 95 C of a maximum of 100 hours in the operating lifetime. Heating: The maximum permanent operating temperature is 80 C at a maximum permanent operating pressure of 10 bars. The short-term malfunction temperature is 95 C of a maximum of 150 hours in the operating time per year. Item no. d [mm] s [mm] l [m] Description unit Uponor MLCP 14x2 1013366 14 2.0 200 white in coils 200m 200 m Uponor Q&E Coupling for Uponor PEXa pipe consisting of: 1 Coupling / Brass 2 PEX-Rings for secure connection / cross linked Polyethylene Item no. d [mm] Description unit Uponor Q&E Coupling 14 1058659 14 with two eval Rings, nature 10 pcs Uponor Q&E Ring natural Made of PE-X. Uponor rings natural intended for Uponor Q&E fittings. Item no. d [mm] colour [-] Description unit Uponor Q&E ring eval without stop edge 1058428 14 natural nature 14 20 pcs Uponor press coupling MLC up to 32 Made of tin-plated brass, with fixed press sleeve, stop ring, pressed identification, colour code and test safety. Press without bevel. Item no. d [mm] Description unit 1015154 14 Uponor press coupling MLC 14-14 10 pcs EEI-Int-RHC-01.12 13

Uponor Radiant Heating/Cooling > Uponor pipe positioning panel Tecto Uponor pipe positioning panel Tecto The Uponor Tecto pipe positioning panel has been specially developed for the installation of underfloor heating/ cooling systems in residential and non-residential buildings. The panels are installed in the floor below the cement or anhydrite screed load distribution layer. Uponor Tecto panels are available in two different thicknesses (ND 30-2 and ND 11), catering for various floor constructions and load-bearing requirements. Your advantages Cost-efficient one-man installation Easy laying thanks to large panels (1450 x 850 mm) Compensation elements for doors, movements joints and wall joints available Double-sided strips for easy connection of element cut-offs with minimum waste Diagonal pipe fixture for installation at 45 angles Suitable pipe sizes from 14 to 17 mm Ensures standardised pipe spacing due to forced pipe paths Proper covering of the insulating layer thanks to integrated sturdy deep-drawn foil Suitable for a wide range of applications thanks to high strength properties (ND 30-2: 500 kg/m²; ND 11: 3.0 t/ m²) System components Systempipe/-Fittings Additional components Manifold/Cabinets Uponor Tecto pipe positioning panel ND 11 + 30-2 PE-Xa pipe 14 + 17 Uponor edging strip Uponor manifold 14 17 Uponor Tecto double sided strips Uponor PE-Xa Q&E coupling Uponor joint profile 100x10 Uponor compression adapter PE-Xa and MLCP Uponor Tecto pipe fixation element Uponor Tecto PE foil for compensation element Uponor Tecto PE foil for compensation element in 45 MLCP pipe 14 + 16 MLC press coupling 14x2 + 16x2 Uponor joint protection 20mm Uponor marking set Uponor screed additive Uponor manifold connection valve set G 1/Rp 1 Uponor cabinet Uponor PE foil 0.2 mm Room controls Control stations Uponor radio control Uponor wired control 24 V 230 V components Uponor control stations - overview 20,5 14 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor pipe positioning panel Tecto Uponor Tecto - System components and accessories Uponor pipe positioning panel with insulation ND 30-2 Pipe fixing panel ND 30-2 for pipes 14-17 mm with heat and sound insulation. Made of expanded polystyrene insulation covered by a black polystyrene foil acc. to DIN EN 13163. DIN EN 13501-1 fire classification: class E. Building-material class B2 conforming to DIN 4102. Approved for moving loads of up to 5.0 kn/m². Thermal resistance: 0.75 m²k/w. For pipe spacing in cm: 10, 15, 20, 25, 30. Dimensions: 1.45 m x 0,85 m Panel height: 52 mm Item no. h1 [mm] h2 [mm] l [mm] w [mm] A [m²] Δ Lw [db] Description unit Uponor Tecto pipe positioning panel incl. 1005478 52/50 30-2 1450 850 1.12 28 Insulation for dim. 14-17, thickness 30mm 8.96 m² Uponor pipe positioning panel with insulation ND 11 Pipe fixing panel ND 11 for pipes 14-17 mm with heat insulation. Made of expanded polystyrene insulation covered by a black polystyrene foil acc. to DIN EN 13163. DIN EN 13501-1 fire classification: class E. Buildingmaterial class B2 conforming to DIN 4102. Approved for moving loads of up to 30 kn/m². Thermal resistance: 0.275 m²k/w. For pipe spacing in cm: 10, 15, 20, 25, 30. Dimensions: 1.45 m x 0,85 m Panel height: 33 mm Item no. h1 [mm] h2 [mm] l [mm] w [mm] A [m²] Δ Lw [db] Description unit Uponor Tecto pipe positioning panel incl. 1005477 33 11 1450 850 1.12 0 Insulation for dim. 14-17, thickness 11mm 15.68 m² l h Uponor compensation insulation element ND 30-2 as heat-/sound insulation for use with the compensation element covering foil in door or wall area. Material: Expanded polystyrene hard foam acc. to DIN EN 13163 Building class according to DIN 4102: B2 Thermal resistance: 0.75 m²k/w. Approved for moving loads of up to 5.0 kn/m². > PS-E < b Item no. h [mm] l [mm] w [mm] Δ Lw [db] A [m²] Description unit Uponor Tecto compensation 1005480 30-2 1400 150 28 0.21 insulation element - thickness 30-2mm 8.4 m l h Uponor compensation insulation element ND 11 as heat-/sound insulation for use with the compensation element covering foil in door or wall area. Material: Expanded polystyrene hard foam acc. to DIN EN 13163 Building class according to DIN 4102: B2 Thermal resistance: 0.275 m²k/w. Approved for moving loads of up to 30 kn/m². > PS b Item no. h [mm] l [mm] w [mm] Δ Lw [db] A [m²] Description unit Uponor Tecto compensation 1005479 11 1400 150 0 0.21 insulation element - thickness 11mm 22.4 m EEI-Int-RHC-01.12 15

Uponor Radiant Heating/Cooling > Uponor pipe positioning panel Tecto Uponor Tecto - System components and accessories l 1 Uponor PE-foil for compensation element For use with compensation-insulation ND 11 or ND 30-2 in door or wall area, consists of: - covering foil with cutter raster, single overlapping, pipe fixing foil for secure connection of compensation elements on the Tecto elements Material: PS-foil Building class according to DIN 4102: B2 Colour of leveling foil: black, approx. RAL 9017 b b 1 > PS < l Item no. l [mm] l1 [mm] w [mm] w1 [mm] A [m²] Description unit Uponor Tecto PE-foil for 1005481 1400 1450 200 150 0.21 compensation insulation element 28 m > PS < b Uponor pipe fixation element 45 Consist of 2 pipe fixing naps connected with one pipe fixation element as stripe with 3 fixations for diagonal installation of Uponor pipes on Uponor Tecto pipe positioning panel. Each stripe is separable in 3 fixation elements. Material: Black deep drawing PS foil. Building-material class B2 conforming to DIN 4102. Item no. w [mm] Description unit Uponor Tecto pipe fixation element 1005482 75 for diagonal installation 10 pcs Uponor PE-foil for compensation element in 45 Covering foil in 45 version for use with compensation-insulation ND 11 or ND 30-2 in door or wall area, consists of: - covering foil with cutter raster, single overlapping, pipe fixing foil for secure connection of compensation elements on the Tecto elements Material: PS-foil Building class according to DIN 4102: B2 Colour of leveling foil: black, aprox. RAL 9017 Item no. l [mm] l1 [mm] w [mm] w1 [mm] A [m²] Description unit Uponor Tecto PE-foil for 1005483 1343 1414 225 150 0.2 compensation insulation element in 45 26.8 m l Uponor double-sided strip Foil strips with pipe fixing studs in two rows for the proper connection of Tecto elements ND 11 or ND 30-2 (butt joints) Material: Deep drawn PS foil DIN 4102 building material class: B2 Colour of cover foil: traffic black (near RAL 9017) b > PS < l 1 h Item no. l [mm] l1 [mm] w [mm] h [mm] Description unit Uponor Tecto double sided strips 1005484 1350 1400 100 22 to connect panels 33.75 m 16 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor pipe positioning panel Tecto Uponor Tecto - System components and accessories Uponor PE-Xa pipe as coil, for use as radiant heating pipe, connected by Q&E, press or clamp fittings. Material: Uponor PE-Xa pipe made in high-pressure cross-linked polyethylene (Engel method), conforming to DIN 16892 and DIN ISO 15875, oxygen-tight according to DIN 4726 Colour: white with black and red longitudinal stripes Uponor PE-Xa pipe Max. operating temperature: 90 C Max. operating pressure: 6 bar at 70 C Application class: 4 / 6 bar Item no. d [mm] s [mm] l [m] Description unit Uponor eval PE-Xa Q&E pipe 14x2.0 1048290 14 2 240 240 m coil 240 m Uponor eval PE-Xa Q&E pipe 14x2.0 1048291 14 2 640 640 m coil 640 m Uponor eval PE-Xa Q&E pipe in coils Pipes manufactured from peroxide cross-linked polyethylene (PE-Xa) using the Engel method, complying with e.g. EN ISO 15875 Plastics piping systems for hot and cold water installations - Cross-linked polyethylene. Includes an ethylene vinyl alcohol (EVOH) oxygen barrier layer, complying with DIN 4726, to prevent corrosion of system components. This barrier has been specially developed to work together with Uponor Q&E fitting technology. Classification of service conditions (including typical field of application): Application class 4 - Underfloor heating and low temperature radiators, malfunction temperature 95 C. Design pressure 6 bar. Application class 5 - high temperature radiators, malfunction temperature 95 C. Design pressure 6 bar. Item no. d [mm] s [mm] l [m] p [bar] Description unit Uponor eval PE-Xa Q&E pipe 1047610 16 2.0 120 6 16x2.0 mm in coils of 120 m 120 m Uponor eval PE-Xa Q&E pipe 1047611 16 2.0 240 6 16x2.0 mm in coils of 240 m 240 m Uponor eval PE-Xa Q&E pipe 1047612 16 2.0 640 6 16x2.0 mm in coils of 640 m 640 m Uponor PE-Xa pipes PE-Xa pipe with an oxygen diffusion barrier manufactured from peroxide cross-linked polyethylene (PE-Xa) using the Engel method complying with e.g. preniso 15875 Plastics piping systems for hot and cold water installations - Cross-linked polyethylene with an oxygen diffusion barrier of EVOH (ethyl vinyl alcohol). Uponor pipes fulfil the requirements for oxygen diffusion resistance as per DIN 4726. Malfunction temperature 95 C. Design pressure 8,8 bar (at 70 C). Item no. d [mm] s [mm] l [m] V [l/m] Description unit Uponor pe PE-Xa Q&E pipe 17x2.0 1034535 17 2.0 120 0.13 120 m coil 120 m Uponor pe PE-Xa Q&E pipe 17x2.0 1009226 17 2.0 240 0.13 240 m coil 240 m Uponor pe PE-Xa Q&E pipe 17x2.0 1009227 17 2.0 640 0.13 640 m coil 640 m EEI-Int-RHC-01.12 17

Uponor Radiant Heating/Cooling > Uponor pipe positioning panel Tecto Uponor Tecto - System components and accessories Uponor MLCP white in coils Diffusion-tight multi-layer composite pipe (PE-RT - adhesive - longitudinally welded aluminium - adhesive - PE-RT) for distribution conduits, rising mains and connection lines for plumbing, radiator connection and fancoil connection. Fire classification E according to DIN EN 13501-1. Pipe end caps as hygienic seal according EN 806. Resistance of temperature: Tap water: The maximum permanent operating temperature exists between 0 C and 70 C at a maximum permanent operating pressure of 10 bars. The short-term malfunction temperature is 95 C of a maximum of 100 hours in the operating lifetime. Heating: The maximum permanent operating temperature is 80 C at a maximum permanent operating pressure of 10 bars. The short-term malfunction temperature is 95 C of a maximum of 150 hours in the operating time per year. Item no. d [mm] s [mm] l [m] Description unit Uponor MLCP 14x2 1013366 14 2.0 200 white in coils 200m 200 m Uponor MLCP 16x2 1013378 16 2.0 100 white in coils 100m 100 m Uponor MLCP 16x2 1013371 16 2.0 200 white in coils 200m 200 m Uponor MLCP 16x2 1013380 16 2.0 500 white in coils 500m 500 m Uponor Q&E Coupling for Uponor PEXa pipe consisting of: 1 Coupling / Brass 2 PEX-Rings for secure connection / cross linked Polyethylene Item no. d [mm] Description unit Uponor Q&E Coupling 14 1058659 14 with two eval Rings, nature 10 pcs Uponor Q&E Coupling 16 1058660 16 with two eval Rings, nature 20 pcs Uponor Q&E Coupling 17 1058661 17 with two eval Rings, nature 10 pcs Uponor Q&E Ring natural Made of PE-X. Uponor rings natural intended for Uponor Q&E fittings. Item no. d [mm] colour [-] Description unit Uponor Q&E ring eval without stop edge 1058428 14 natural nature 14 20 pcs Uponor Q&E Ring eval with stop edge 1042389 16 natural nature 16 20 pcs Uponor Q&E ring eval without stop edge 1058429 17 natural nature 17 20 pcs Uponor press coupling MLC up to 32 Made of tin-plated brass, with fixed press sleeve, stop ring, pressed identification, colour code and test safety. Press without bevel. Item no. d [mm] Description unit 1015154 14 Uponor press coupling MLC 14-14 10 pcs 1015164 16 Uponor press coupling MLC 16-16 10 pcs 18 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor self attaching system Uponor self attaching system With its self attaching system, Uponor offers installers an innovating pipe laying system for underfloor heating pipes. At the factory, hook fasting tape is wound around the oxygentight pipes conforming to DIN 4726. The system insulating panel, which can also be used as a stapler panel, is completely covered with the matching laminated loop foil. The pipe can be reeled off and laid on the floor as usual and only needs to be pressed at the correct position against the laminated insulating panel. The hooks on the tape around the pipe catch the loops on the foil and thus secure the pipe to the surface. Both the hook take and the loop foil are designed to guarantee maximum fixture. Your advantages Easy pipe laying without any special tools For cost-efficient one-man installation Installed pipes can be repositioned at any time System panels available in various thicknesses to suit individual insulation needs Roll-out insulation for fast installation Ideal for flexible pipe spacing in rooms of any shape Thanks to the large number of fastening points, the pipe is firmly placed against the surface along its entire length System components Systempipe/-Fittings Additional components Manifold/Cabinets Uponor self attaching insulation roll panel Uponor PE-Xa self attaching pipe 16 x 1.8 Uponor edging strip Uponor manifold Uponor self attaching insulation fold panel Uponor MLCP self attaching pipe 16x2.0 Uponor joint profile 100x10 Uponor compression adapter PE-Xa and MLCP Uponor tape Uponor PE-Xa Q&E coupling MLC press coupling 16x2 Uponor joint protection 20mm Uponor marking set Uponor manifold connection valve set G 1/Rp 1 Uponor screed additive Uponor cabinet Uponor PE foil 0.2 mm Room controls Control stations Uponor radio control Uponor wired control 24 V 230 V components Uponor control stations - overview 20,5 EEI-Int-RHC-01.12 19

Uponor Radiant Heating/Cooling > Uponor self attaching system Uponor self attaching system - System components and accessories Uponor self attaching insulation roll panel Pipe fixing panel in roll form, for thermal and impact noise insulation according to DIN EN 13163 and DIN 4108-10; made from EPS rigid foam with laminated textile adhesive foil for overlap installation; foil extending on one side to cover insulating layer according to DIN 18560. Foil raster: 100 x 100 mm DIN EN 13501-1 fire classification: class E Item no. h [mm] l [mm] w [mm] G [kn/m²] R-value [m²k/w] Δ Lw [db] Description unit Uponor self attaching insulation roll panel 25-2 1007226 25-2 12000 1000 4 0.56 28 EPS 045 DES SM 12 m² Uponor self attaching insulation roll panel 30-3 1007228 30-3 12000 1000 4 0.67 29 EPS 045 DES SM 12 m² Uponor self attaching insulation fold panel Pipe fixing panel, for thermal and impact noise insulation according to DIN EN 13163 and DIN 4108-10; made from EPS rigid foam with laminated textile adhesive foil for overlap installation; foil extending on one side to cover insulating layer according to DIN 18560. Foil raster: 100 x 100 mm DIN EN 13501-1 fire classification: class E Item no. h [mm] l [mm] w [mm] G [kn/m²] R-value [m²k/w] Δ Lw [db] Description unit Uponor self attaching insulation fold panel 30-3 1007232 30-3 2000 1000 4 0.67 29 10 m² Uponor self attaching insulation fold panel 15mm Pipe fixing panel, for thermal insulation according to DIN EN 13163 and DIN 4108-10; made from EPS rigid foam with laminated textile adhesive foil for overlap installation; foil extending on one side to cover insulating layer according to DIN 18560. Foil raster: 100 x 100 mm DIN EN 13501-1 fire classification: class E Item no. h [mm] l [mm] w [mm] G [kn/m²] R-value [m²k/w] Δ Lw [db] Description unit Uponor self attaching insulation fold panel 15mm 1007234 15 2000 1000 30 0.38 - EPS 040 DEO 20 m² Uponor tape Tape for the sealed joining of Uponor insulation, applied with hand-held roll device. Roll length 66m. Item no. l [m] Description unit 1000012 66 Uponor tape 50 mm 20 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor self attaching system Uponor self attaching system - System components and accessories Uponor PE-Xa self attaching pipes PE-Xa pipe with an oxygen diffusion barrier of EVOH manufactured from peroxide cross-linked polyethylene (PE-Xa) using the Engel method complying with DIN 16892 and DIN ISO 15875, oxygen tight according to DIN 4726. Max. operating temperature: 70 C Application class 4 / 6 bar. Item no. d [mm] s [mm] l [m] Description unit Uponor self attaching eval PE-Xa pipe 16x1.8 1047624 16 1.8 240 240 m coil 240 m Uponor self attaching eval PE-Xa pipe 16x1.8 1047625 16 1.8 640 640 m coil 640 m Uponor MLCP UFH/C self attaching pipes Diffusion-tight multi layer composite pipe (PE-RT - adhesive agent - longitudinally welded aluminium - adhesive agent - PE-RT) for radiant heating / cooling applications. Normally inflammable, materials classification B2 according to DIN 4102. Max. continuous operation pressure: 4 bar at continuous operating temperature 60 C. Item no. d [mm] s [mm] l [m] Description unit Uponor MLCP self attaching red heating UFH/C 16x2.0 1048249 16 2 200 200m pipe with oxygen barrier 200 m Uponor MLCP self attaching red heating UFH/C 16x2.0 1048395 16 2 500 500m pipe with oxygen barrier 500 m Uponor Q&E Coupling for Uponor PEXa pipe consisting of: 1 Coupling / Brass 2 PEX-Rings for secure connection / cross linked Polyethylene Item no. d [mm] Description unit Uponor Q&E Coupling 16 1058660 16 with two eval Rings, nature 20 pcs Uponor Q&E Ring natural Made of PE-X. Uponor rings natural intended for Uponor Q&E fittings. Item no. d [mm] colour [-] Description unit Uponor Q&E Ring eval with stop edge 1042389 16 natural nature 16 20 pcs Uponor press coupling MLC up to 32 Made of tin-plated brass, with fixed press sleeve, stop ring, pressed identification, colour code and test safety. Press without bevel. Item no. d [mm] Description unit 1015164 16 Uponor press coupling MLC 16-16 10 pcs EEI-Int-RHC-01.12 21

Uponor Radiant Heating/Cooling > Uponor stapler and clamp track Uponor stapler and clamp track system All components of the Uponor stapler and clamp track system are designed to perfectly match each other. The panels with thermal and impact noise insulation are equipped with a tear-proof surface and a printed installation grid. They allow for easy installation of the system pipe. These and all other components are designed to ensure optimum safety and reliable operation of the system. Your advantages Flexible pipe laying Available as composite panels or rolls with a range of different thermal and impact noise insulation layers Suitable for all types of screeds Large pipe coils reel for minimum cut-offs and twist-fee installation Fast to install thanks to the integrated insulation layer cover Universal staple nail for pipe thickness of 14 20 mm Easy installation with ergonomically designed Uponor system stapler System components Systempipe/-Fittings Additional components Manifold/Cabinets Uponor insulation roll Uponor PE-Xa pipe Uponor edging strip Uponor manifold Uponor pipe staple nail Uponor MLCP pipe Uponor joint profile 100x10 Uponor compression adapter PE-Xa and MLCP Uponor tape Uponor PE-Xa Q&E coupling Uponor joint protection 20mm Uponor clamp track MLC press coupling 14x2 + 16x2 + 20x2,25 Uponor marking set Uponor manifold connection valve set G 1/Rp 1 Uponor fastening nail Uponor screed additive Uponor cabinet Uponor stapler Uponor PE foil 0.2 mm Room controls Control stations Uponor radio control Uponor wired control 24 V 230 V components Uponor control stations - overview 20,5 22 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor stapler and clamp track Uponor stapler and clamp track - System components and accessories Uponor insulation roll panel with texture foil Ready-to-lay heat/sound insulation roll, consisting of: tear-resistant texture foil laminated onto 25-2 EPS 045 DES sm as per DIN EN 13163 and DIN V 4108-10 (WLG 045). DIN EN 13501-1 fire classification: class E. Standard flammability, building-material class B2, conforming to DIN 4102. Suitable for use in area between floors, where rooms on either side are heated to same level. With printed-on grid pattern for ease of cutting and alignment. Approved for moving loads of up to 4.0 kn/m². Thermal resistance: 0,56 (m² x K/W). Item no. h [mm] l [mm] w [mm] G [kn/m²] R-value [m²k/w] Δ Lw [db] Description unit Uponor insulation roll panel with texture foil 1000002 30-2 12000 1000 5 0.75 28 typ 30-2 12 m² Uponor insulation roll panel with texture foil 1000003 30-3 12000 1000 4 0.67 29 typ 30-3 12 m² Uponor PE pattern foil 0.25mm 0,25 mm-thick foil with printed on pattern 100 x 100 mm for laying over existing heat/sound insulation and fixation of clamp tracks. Prevents screed from flowing down into the insulating layer. Dimensions: 100 m x 1.03 m Item no. l [m] w [m] s [mm] Description unit Uponor PE pattern foil 0.25mm thickness 1000015 100 1.03 0.25 for clamp track fixation 103 m² Uponor pipe fixing foil Multi-layer reflection and impact foil, designed to improve thermal insulation and distribution; also serving as damping course. With printed raster. Load capacity: 15 kn/m2 Roll width: 1 m Roll length: 60 m Foil height: 4 mm Item no. l [m] w [m] s [mm] G [kn/m²] Description unit 1000017 60 1 4 15 Uponor pipe fixing foil 4 mm 60 m² Uponor Pipe Clip standard Pipe staple "Standard" in blue, loaded into magazine for securing heatingsystem pipes onto insulation. For Uponor pipes 14-20 mm. Item no. d [mm] Description unit Uponor Pipe Clip standard 1002296 14-20 Ø: 14-20 mm, H = 40 mm 1000 pcs Uponor Pipe Clip long Pipe staple "Long" in grey, loaded into magazine for securing heatingsystem pipes onto insulation. For Uponor pipes 14-20 mm. Item no. d [mm] Description unit Uponor Pipe Clip long 1002297 14-20 Ø: 14-20 mm, H = 55 mm 300 pcs EEI-Int-RHC-01.12 23

Uponor Radiant Heating/Cooling > Uponor stapler and clamp track Uponor stapler and clamp track - System components and accessories Uponor clamp track 14 d r a h Self-adhesive U-profile strip made of recycled material, with integrated pipe holder for 14 x 2 mm Uponor pipes. Rated break points are provided every 100 mm for easy separation. Length of track: 2.5 m Width of track: 38 mm Space between pipe holders: 50 mm c/c Installation height with pipe: 17 mm l b Item no. l [mm] w [mm] h [mm] d [mm] c/c [mm] Description unit 1005498 2500 38 17 14 50 Uponor clamp track 14 mm 25 m Uponor clamp track 16 d r a h Self-adhesive U-profile strip made of recycled material, with integrated pipe holder for 16 x 2 mm Uponor pipes. Rated break points are provided every 100 mm for easy separation. Length of track: 2 m Width of track: 40 mm Space between pipe holders: 25 mm c/c Installation height with pipe: 25 mm l b Item no. l [mm] w [mm] h [mm] d [mm] c/c [mm] Description unit 1013127 2000 40 25 16 25 Uponor clamp track 16 mm 100 m Uponor clamp track 14-20 Self-adhesive U-profile strip made of recycled material, with integrated pipe holder for Uponor pipes 14-20 mm. Length of track: 1 m Width of track: 50 mm Space between pipe holders: 50 mm c/c Installation height with pipe: 27 mm Item no. l [mm] w [mm] h [mm] c/c [mm] Description unit 1000018 1000 50 27 50 Uponor clamp track 14-20 mm 100 m Uponor fastening nail The purpose of the fastening nail is to fix the Uponor clamp track and the fixing-foil or the pipe positioning panel to the underlaying layer of insulation. Can also be used for additional manual fastening of Uponor MLC and PE-Xa pipes. 1000019 Uponor fastening nail 500 pcs 24 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor stapler and clamp track Uponor stapler and clamp track - System components and accessories Uponor PE-Xa pipe as coil, for use as radiant heating pipe, connected by Q&E, press or clamp fittings. Material: Uponor PE-Xa pipe made in high-pressure cross-linked polyethylene (Engel method), conforming to DIN 16892 and DIN ISO 15875, oxygen-tight according to DIN 4726 Colour: white with black and red longitudinal stripes Uponor PE-Xa pipe Max. operating temperature: 90 C Max. operating pressure: 6 bar at 70 C Application class: 4 / 6 bar Item no. d [mm] s [mm] l [m] Description unit Uponor eval PE-Xa Q&E pipe 14x2.0 1048290 14 2 240 240 m coil 240 m Uponor eval PE-Xa Q&E pipe 14x2.0 1048291 14 2 640 640 m coil 640 m Uponor eval PE-Xa Q&E pipe in coils Pipes manufactured from peroxide cross-linked polyethylene (PE-Xa) using the Engel method, complying with e.g. EN ISO 15875 Plastics piping systems for hot and cold water installations - Cross-linked polyethylene. Includes an ethylene vinyl alcohol (EVOH) oxygen barrier layer, complying with DIN 4726, to prevent corrosion of system components. This barrier has been specially developed to work together with Uponor Q&E fitting technology. Classification of service conditions (including typical field of application): Application class 4 - Underfloor heating and low temperature radiators, malfunction temperature 95 C. Design pressure 6 bar. Application class 5 - high temperature radiators, malfunction temperature 95 C. Design pressure 6 bar. Item no. d [mm] s [mm] l [m] p [bar] Description unit Uponor eval PE-Xa Q&E pipe 1047610 16 2.0 120 6 16x2.0 mm in coils of 120 m 120 m Uponor eval PE-Xa Q&E pipe 1047611 16 2.0 240 6 16x2.0 mm in coils of 240 m 240 m Uponor eval PE-Xa Q&E pipe 1047612 16 2.0 640 6 16x2.0 mm in coils of 640 m 640 m Uponor PE-Xa pipes PE-Xa pipe with an oxygen diffusion barrier manufactured from peroxide cross-linked polyethylene (PE-Xa) using the Engel method complying with e.g. preniso 15875 Plastics piping systems for hot and cold water installations - Cross-linked polyethylene with an oxygen diffusion barrier of EVOH (ethyl vinyl alcohol). Uponor pipes fulfil the requirements for oxygen diffusion resistance as per DIN 4726. Malfunction temperature 95 C. Design pressure 8,8 bar (at 70 C). Item no. d [mm] s [mm] l [m] V [l/m] Description unit Uponor pe PE-Xa Q&E pipe 17x2.0 1034535 17 2.0 120 0.13 120 m coil 120 m Uponor pe PE-Xa Q&E pipe 17x2.0 1009226 17 2.0 240 0.13 240 m coil 240 m Uponor pe PE-Xa Q&E pipe 17x2.0 1009227 17 2.0 640 0.13 640 m coil 640 m Uponor pe PE-Xa Q&E pipe 20x2.0 1009228 20 2.0 120 0.2 120 m coil 120 m Uponor pe PE-Xa Q&E pipe 20x2.0 1009230 20 2.0 240 0.2 240 m coil 240 m Uponor pe PE-Xa Q&E pipe 20x2.0 1009231 20 2.0 480 0.2 480 m coil 480 m EEI-Int-RHC-01.12 25

Uponor Radiant Heating/Cooling > Uponor stapler and clamp track Uponor stapler and clamp track - System components and accessories Uponor MLCP white in coils Diffusion-tight multi-layer composite pipe (PE-RT - adhesive - longitudinally welded aluminium - adhesive - PE-RT) for distribution conduits, rising mains and connection lines for plumbing, radiator connection and fancoil connection. Fire classification E according to DIN EN 13501-1. Pipe end caps as hygienic seal according EN 806. Resistance of temperature: Tap water: The maximum permanent operating temperature exists between 0 C and 70 C at a maximum permanent operating pressure of 10 bars. The short-term malfunction temperature is 95 C of a maximum of 100 hours in the operating lifetime. Heating: The maximum permanent operating temperature is 80 C at a maximum permanent operating pressure of 10 bars. The short-term malfunction temperature is 95 C of a maximum of 150 hours in the operating time per year. Item no. d [mm] s [mm] l [m] Description unit Uponor MLCP 14x2 1013366 14 2.0 200 white in coils 200m 200 m Uponor MLCP 16x2 1013371 16 2.0 200 white in coils 200m 200 m Uponor MLCP 16x2 1013378 16 2.0 100 white in coils 100m 100 m Uponor MLCP 16x2 1013380 16 2.0 500 white in coils 500m 500 m Uponor MLCP 20x2,25 1013392 20 2.25 200 white in coils 200m 200 m Uponor Q&E Coupling for Uponor PEXa pipe consisting of: 1 Coupling / Brass 2 PEX-Rings for secure connection / cross linked Polyethylene Item no. d [mm] Description unit Uponor Q&E Coupling 14 1058659 14 with two eval Rings, nature 10 pcs Uponor Q&E Coupling 16 1058660 16 with two eval Rings, nature 20 pcs Uponor Q&E Coupling 17 1058661 17 with two eval Rings, nature 10 pcs Uponor Q&E Coupling 20 1058668 20 with two eval Rings, nature 10 pcs Uponor Q&E Ring natural Made of PE-X. Uponor rings natural intended for Uponor Q&E fittings. Item no. d [mm] colour [-] Description unit Uponor Q&E ring eval without stop edge 1058428 14 natural nature 14 20 pcs Uponor Q&E Ring eval with stop edge 1042389 16 natural nature 16 20 pcs Uponor Q&E ring eval without stop edge 1058429 17 natural nature 17 20 pcs Uponor Q&E Ring eval with stop edge 1042837 20 natural nature 20 20 pcs Uponor press coupling MLC up to 32 Made of tin-plated brass, with fixed press sleeve, stop ring, pressed identification, colour code and test safety. Press without bevel. Item no. d [mm] Description unit 1015154 14 Uponor press coupling MLC 14-14 10 pcs 1015164 16 Uponor press coupling MLC 16-16 10 pcs 1015187 20 Uponor press coupling MLC 20-20 10 pcs 26 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor pipe positioning panel Uponor pipe positioning panel 14-16 The Uponor installation panel has been specially developed for the installation of underfloor heating/cooling systems in residential and non-residential buildings. The panels are installed in the floor below the cement or anhydrite screed load distribution layer. Uponor installation panels are available in two different thicknesses with insulation (ND30-2) and without insulation (ND11), catering for various floor constructions and load-bearing requirements. Your advantages Cost-efficient one-man installation Easy laying thanks to large panels (1447 x 900 mm) Compensation elements for doors, movements joints and wall joints available Suitable pipe sizes from 14 to 16 mm Ensures standardised pipe spacing due to forced pipe paths Proper covering of the insulating layer thanks to integrated sturdy deep-drawn foil Suitable for a wide range of applications thanks to high strength properties (ND 30-2: 5 kn/m²; ND 11: 30 kn/ m²) System components Systempipe/-Fittings Additional components Manifold/Cabinets Uponor installation panel 14-16 ND11 Uponor PE-Xa pipe Uponor edging strip Uponor manifold Uponor installation panel 14-16 ND Uponor Q&E coupling Uponor joint profile 100x10 Uponor compression adapter PE-Xa and MLCP MLCP pipe 14 + 16 Uponor joint protection 20mm Uponor pipe positioning panel MLC press coupling 14x2 + 16x2 Uponor marking set Uponor manifold connection valve set G 1/Rp 1 Uponor screed additive Uponor cabinet Uponor PE foil 0.2 mm Room controls Control stations Uponor radio control Uponor wired control 24 V 230 V components Uponor control stations - overview 20,5 EEI-Int-RHC-01.12 27

Uponor Radiant Heating/Cooling > Uponor pipe positioning panel Uponor pipe positioning panel - System components and accessories Uponor installation foil 14-16 Foil element without foamed back panel. Vacuum-formed PS deep-drawn foil made of impact-proof polystyrene with integrated pipe fixing studs for proper pipe spacing and exact installation of the Uponor system pipes at the required height. The deep-drawn foil overlaps on two sides; when laid in a staggered pattern, the foil layer is thus continuous. For installation on top of insulation layer. Right-angled: RA 5.5 11 16,5 22 27.5 33 cm Diagonal: RA 7.5 15 22.5 30 cm Dimensions of element foil: 1447 x 900 m Item no. h1 [mm] l [mm] w [mm] A [m²] Δ Lw [db] Description unit Uponor pipe positioning panel 1016703 18 1447 900 1.2 0 14-16 mm 10 m² Uponor installation panel 14-16 / 30-2 For cement and self-levelling cement screeds; allows for right-angled or diagonal pipe installation at 6 plus 4 different pipe distances; for optimised heating pipe installation based on actual room geometry with minimum cut-offs thanks to sophisticated system technology; allows for fast and easy installation of the hard/soft PS rigid foam panels with overlapping foil edges. Meets the requirements for standard impact noise insulation (DIN 4109), thermal insulation (DIN EN1264), DIN EN 13501-1 fire classification: class E, fire safety (DIN 4102) B2 and heat output (DIN EN 1264), irrespective of the pipe spacing; the height and distance of the sturdy pipe holders (DIN EN 1264) are fixed to prevent shifting of the pipes; the overlapping application foil acts as a damp-proofing course and eliminates sound bridges (DIN 18560); protects the environment thanks to use of environmentally friendly PS. Properties subject to continuous RAL quality monitoring. Pipe spacing with right-angle installation: RA 5.5-11 - 16.5-22 - 27.5-33 cm Pipe spacing with diagonal installation: RA 7.5-15 - 22.5-30 cm Type: 30-2 mm, for universal use in residential and commercial buildings up to 5 kn/m2 EPS 040 DES sg Dimensions: 1447 x 900 mm Plate thickness: 48 mm Impact noise insulation: 28 db Application range: up to 5 kn/m2 Thermal resistance: R = 0.75 m2k/w Item no. h1 [mm] h2 [mm] l [mm] w [mm] A [m²] Δ Lw [db] Description unit Uponor nap panel 14-16mm incl. 1016699 50/48 30-2 1447 900 1.2 28 Insulation, thickness 30mm 10 m² 28 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor pipe positioning panel Uponor pipe positioning panel - System components and accessories Uponor installation panel 14-16 / 11 For cement and self-levelling cement screeds; allows for right-angled or diagonal pipe installation at 6 plus 4 different pipe distances; for optimised heating pipe installation based on actual room geometry with minimum cut-offs thanks to sophisticated system technology; allows for fast and easy installation of the hard/soft PS rigid foam panels with overlapping foil edges. Meets the requirements for standard impact noise insulation (DIN 4109), thermal insulation (DIN EN1264), DIN EN 13501-1 fire classification: class E, fire safety (DIN 4102) B2 and heat output (DIN EN 1264), irrespective of the pipe spacing; the height and distance of the sturdy pipe holders (DIN EN 1264) are fixed to prevent shifting of the pipes; the overlapping application foil acts as a damp-proofing course and eliminates sound bridges (DIN 18560); protects the environment thanks to use of environmentally friendly PS. Properties subject to continuous RAL quality monitoring. Pipe spacing with right-angle installation: RA 5.5-11 - 16.5-22 - 27.5-33 cm Pipe spacing with diagonal installation: RA 7.5-15 - 22.5-30 cm Type: 11 mm, for universal use in residential and commercial buildings up to 30 kn/m2 EPS 035 DE0 dm (100kPa) Dimensions: 1447 x 900 mm Plate thickness: 29 mm Application range: up to 30 kn/m2 Item no. h1 [mm] h2 [mm] l [mm] w [mm] A [m²] Δ Lw [db] Description unit Uponor nap panel 14-16mm incl. 1016700 29 11 1447 900 1.2 0 Insulation, thickness 11mm 10 m² Uponor installation panel 14-16 manifold/door kit 30-2 For universal use, facilitating pipe laying near manifolds thanks to special manifold element. Stud overlap allows for easy integration into element structure. Door element designed for straight door openings; can be cut into customised door element strips. Per panel, you can cut 10 strips catering for 5 doors. Universal use of element thanks to easy adjustment to complex room geometries including angled door openings. Type: 30-2 VT EPS 040 DES sg Dimensions: 1447 x 900 mm Application range: up to 5 kn/m2 consisting of: 2.5 m2 manifold element foil (2 panels) 2.5 m2 door element foil (2 panels) 5 m2 30-2 mm thermal and impact noise insulation (4 panels) Item no. h1 [mm] h2 [mm] l [mm] w [mm] A [m²] Δ Lw [db] Description unit Uponor manifold-/door set for nap panel 14-16mm 1016701 50/48 30-2 1420 900 1.2 28 thickness 30mm 5 m² EEI-Int-RHC-01.12 29

Uponor Radiant Heating/Cooling > Uponor pipe positioning panel Uponor pipe positioning panel - System components and accessories Uponor installation panel 14-16 manifold/door kit 11 For universal use, facilitating pipe laying near manifolds thanks to special manifold element. Stud overlap allows for easy integration into element structure. Door element designed for straight door openings; can be cut into customised door element strips. Per panel, you can cut 10 strips catering for 5 doors. Universal use of element thanks to easy adjustment to complex room geometries including angled door openings. Type: 11 VT EPS 035 DEO dm (100 kpa) Dimensions: 1447 x 900 mm Application range: up to 30 kn/m2 consisting of: 2.5 m2 manifold element foil (2 panels) 2.5 m2 door element foil (2 panels) 5 m2 11mm thermal insulation (4 panels) Item no. h1 [mm] h2 [mm] l [mm] w [mm] A [m²] Δ Lw [db] Description unit Uponor manifold-/door set for nap panel 14-16mm 1016702 29 11 1420 900 1.2 0 thickness 11mm 5 m² Uponor PE-Xa pipe as coil, for use as radiant heating pipe, connected by Q&E, press or clamp fittings. Material: Uponor PE-Xa pipe made in high-pressure cross-linked polyethylene (Engel method), conforming to DIN 16892 and DIN ISO 15875, oxygen-tight according to DIN 4726 Colour: white with black and red longitudinal stripes Uponor PE-Xa pipe Max. operating temperature: 90 C Max. operating pressure: 6 bar at 70 C Application class: 4 / 6 bar Item no. d [mm] s [mm] l [m] Description unit Uponor eval PE-Xa Q&E pipe 14x2.0 1048290 14 2 240 240 m coil 240 m Uponor eval PE-Xa Q&E pipe 14x2.0 1048291 14 2 640 640 m coil 640 m Uponor eval PE-Xa Q&E pipe in coils Pipes manufactured from peroxide cross-linked polyethylene (PE-Xa) using the Engel method, complying with e.g. EN ISO 15875 Plastics piping systems for hot and cold water installations - Cross-linked polyethylene. Includes an ethylene vinyl alcohol (EVOH) oxygen barrier layer, complying with DIN 4726, to prevent corrosion of system components. This barrier has been specially developed to work together with Uponor Q&E fitting technology. Classification of service conditions (including typical field of application): Application class 4 - Underfloor heating and low temperature radiators, malfunction temperature 95 C. Design pressure 6 bar. Application class 5 - high temperature radiators, malfunction temperature 95 C. Design pressure 6 bar. Item no. d [mm] s [mm] l [m] p [bar] Description unit Uponor eval PE-Xa Q&E pipe 1047610 16 2.0 120 6 16x2.0 mm in coils of 120 m 120 m Uponor eval PE-Xa Q&E pipe 1047611 16 2.0 240 6 16x2.0 mm in coils of 240 m 240 m Uponor eval PE-Xa Q&E pipe 1047612 16 2.0 640 6 16x2.0 mm in coils of 640 m 640 m 30 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor pipe positioning panel Uponor pipe positioning panel - System components and accessories Uponor MLCP white in coils Diffusion-tight multi-layer composite pipe (PE-RT - adhesive - longitudinally welded aluminium - adhesive - PE-RT) for distribution conduits, rising mains and connection lines for plumbing, radiator connection and fancoil connection. Fire classification E according to DIN EN 13501-1. Pipe end caps as hygienic seal according EN 806. Resistance of temperature: Tap water: The maximum permanent operating temperature exists between 0 C and 70 C at a maximum permanent operating pressure of 10 bars. The short-term malfunction temperature is 95 C of a maximum of 100 hours in the operating lifetime. Heating: The maximum permanent operating temperature is 80 C at a maximum permanent operating pressure of 10 bars. The short-term malfunction temperature is 95 C of a maximum of 150 hours in the operating time per year. Item no. d [mm] s [mm] l [m] Description unit Uponor MLCP 14x2 1013366 14 2.0 200 white in coils 200m 200 m Uponor MLCP 16x2 1013378 16 2.0 100 white in coils 100m 100 m Uponor MLCP 16x2 1013371 16 2.0 200 white in coils 200m 200 m Uponor MLCP 16x2 1013380 16 2.0 500 white in coils 500m 500 m Uponor Q&E Coupling for Uponor PEXa pipe consisting of: 1 Coupling / Brass 2 PEX-Rings for secure connection / cross linked Polyethylene Item no. d [mm] Description unit Uponor Q&E Coupling 14 1058659 14 with two eval Rings, nature 10 pcs Uponor Q&E Coupling 16 1058660 16 with two eval Rings, nature 20 pcs Uponor Q&E Ring natural Made of PE-X. Uponor rings natural intended for Uponor Q&E fittings. Item no. d [mm] colour [-] Description unit Uponor Q&E ring eval without stop edge 1058428 14 natural nature 14 20 pcs Uponor Q&E Ring eval with stop edge 1042389 16 natural nature 16 20 pcs Uponor press coupling MLC up to 32 Made of tin-plated brass, with fixed press sleeve, stop ring, pressed identification, colour code and test safety. Press without bevel. Item no. d [mm] Description unit 1015154 14 Uponor press coupling MLC 14-14 10 pcs 1015164 16 Uponor press coupling MLC 16-16 10 pcs EEI-Int-RHC-01.12 31

Uponor Radiant Heating/Cooling > Uponor steel mesh Classic Uponor steel mesh system Classic The Uponor steel mesh system Classic is the ideal solution for underfloor heating/cooling systems on virtually all floors in new residential and commercial buildings. Available in three raster sizes, Uponor Classic allows you to optimise the pipe spacing to meet the actual heating needs. As the heating layer is separated from the insulation layer(s), the system, in combination with high-payload insulation, is also ideally suited for areas with high traffic and payload, such as garage showrooms, production halls, retail outlets, etc. Your advantages Exact pipe laying: the steel mesh and pipe holders ensure standardized pipe distances along both horizontal and vertical. Sturdy clamping: the pipe clips secure the pipe firmly on the carrier element. No damage to insulation covering Free hand when choosing your insulating material. Cost-efficient one-man installation: flexible, fast and easy to install, saving you time and money. System components Systempipe/-Fittings Additional components Manifold/Cabinets Uponor steel mesh Uponor PE-Xa pipe 17x2,0 + 20x2,0 Uponor edging strip Uponor manifold Uponor PE Foil 0.2mm PE-type 200 Uponor Q&E coupling Uponor joint profile 100x10 Uponor compression adapter PE-Xa and MLCP Uponor calbe tie Uponor joint protection 20mm Uponor marking set Uponor manifold connection valve set G 1/Rp 1 Uponor tying wire Uponor screed additive Uponor cabinet Uponor pipe holder clip Uponor PE foil 0.2 mm Room controls Control stations Uponor radio control Uponor wired control 24 V 230 V components Uponor control stations - overview 20,5 e.g. can be used with Knauf Floor Screed FE 80 32 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor steel mesh Classic Uponor Classic - System components and accessories Uponor Classic steel mesh For stable attachment of pipe fixations and standard installation of underfloor heating pipes. Dim. 2100mm x 1200mm. Material: corrosion protected steel. Item no. l [mm] w [mm] d [mm] r [mm] A [m²] Description unit Uponor Classic element 10cm 1005084 2100 1200 3 100 2.5 grid 10 and 20, corrosion protected 25 m² Uponor Classic element 15cm 1005087 2100 1200 3 150 2.5 grid 15 and 30, corrosion protected 25 m² Uponor PE foil 0.2mm For installation on Uponor insulation or on standardised insulating material approved for the intended purpose for areas without stud foil. Prevents screed penetrating the underlying insulation. Dimensions: 4 m x 2.5 m Thickness: 0.2 mm Item no. l [m] w [m] s [mm] Description unit Uponor PE foil 0.2 mm thickness 1005049 60 1.25 ~0.2 60 x 1.25 m 75 m² Uponor pipe fixing foil Multi-layer reflection and impact foil, designed to improve thermal insulation and distribution; also serving as damping course. With printed raster. Load capacity: 15 kn/m2 Roll width: 1 m Roll length: 60 m Foil height: 4 mm Item no. l [m] w [m] s [mm] G [kn/m²] Description unit 1000017 60 1 4 15 Uponor pipe fixing foil 4 mm 60 m² Uponor pipe holder clip Plastic clip for fixation of 15-20mm pipes on steel mesh below or equal 6mm. Item no. 1044181 Description Uponor pipe holder clip for pipes 15-20mm on steel mesh below or equal 6mm 100 pcs Uponor tying wire For fastening Uponor pipes on reinforcement steel meshes. Made of steel. 250 pcs per bag. 1009222 Uponor tying wire, 150 x 1.25 250 pcs Uponor cable tie For fastening Uponor pipes on reinforcement steel meshed. Made of polyamide. Item no. w [mm] l [mm] Description unit Uponor cable ties, length 200 mm 1005287 5 200 for the pipe assembly on support mats 100 pcs EEI-Int-RHC-01.12 33

Uponor Radiant Heating/Cooling > Uponor steel mesh Classic Uponor Classic - System components and accessories Uponor PE-Xa pipes PE-Xa pipe with an oxygen diffusion barrier manufactured from peroxide cross-linked polyethylene (PE-Xa) using the Engel method complying with e.g. preniso 15875 Plastics piping systems for hot and cold water installations - Cross-linked polyethylene with an oxygen diffusion barrier of EVOH (ethyl vinyl alcohol). Uponor pipes fulfil the requirements for oxygen diffusion resistance as per DIN 4726. Malfunction temperature 95 C. Design pressure 8,8 bar (at 70 C). Item no. d [mm] s [mm] l [m] V [l/m] Description unit Uponor pe PE-Xa Q&E pipe 17x2.0 1034535 17 2.0 120 0.13 120 m coil 120 m Uponor pe PE-Xa Q&E pipe 17x2.0 1009226 17 2.0 240 0.13 240 m coil 240 m Uponor pe PE-Xa Q&E pipe 17x2.0 1009227 17 2.0 640 0.13 640 m coil 640 m Uponor pe PE-Xa Q&E pipe 20x2.0 1009228 20 2.0 120 0.2 120 m coil 120 m Uponor pe PE-Xa Q&E pipe 20x2.0 1009230 20 2.0 240 0.2 240 m coil 240 m Uponor pe PE-Xa Q&E pipe 20x2.0 1009231 20 2.0 480 0.2 480 m coil 480 m Uponor Q&E Coupling for Uponor PEXa pipe consisting of: 1 Coupling / Brass 2 PEX-Rings for secure connection / cross linked Polyethylene Item no. d [mm] Description unit Uponor Q&E Coupling 17 1058661 17 with two eval Rings, nature 10 pcs Uponor Q&E Coupling 20 1058668 20 with two eval Rings, nature 10 pcs Uponor Q&E Ring natural Made of PE-X. Uponor rings natural intended for Uponor Q&E fittings. Item no. d [mm] colour [-] Description unit Uponor Q&E ring eval without stop edge 1058429 17 natural nature 17 20 pcs Uponor Q&E Ring eval with stop edge 1042837 20 natural nature 20 20 pcs 34 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor Plaster Ceiling Cooling Uponor plaster ceiling cooling system When it comes to managing room temperature with comfort and cost in mind, the Uponor plaster system is truly multitalented as it can be used in ceilings or walls and for cooling as well as heating. Your advantages Minimum installation height A universal system for ceilings and walls mounting Very few, optimally interacting system components Choice of preference for decades Uponor PE-Xa pipe 9,9 x 1,1 mm Q&E fitting system for fast,economical installation Quick reaction time thanks to slim plaster coverage Saves energy thanks to optimum operating temperatures System components Systempipe/-Fittings Additional components Manifold/Cabinets Uponor clamp track Uponor PE-Xa pipe 9,9 x 1,1 Uponor PE-Xa pipe 20x2 Uponor manifold Uponor Minitec coupling 9,9 Uponor Q&E T-reducer 20/9,9/20 Uponor compression adapter PE-Xa and MLCP Uponor Minitec expander tool Uponor Q&E jointing reducer 9,9/20 Uponor manifold connection valve set G 1/Rp 1 Uponor cabinet Room controls Control stations Uponor radio control Uponor wired control 24 V 230 V components Uponor control stations - overview 20,5 e.g. can be used with Knauf MP 75 Projection Plaster EEI-Int-RHC-01.12 35

Uponor Radiant Heating/Cooling > Uponor Plaster Ceiling Cooling Uponor Plaster Wall/Ceiling H/C - System components and accessories d r a Uponor clamp track 9.9 Self-adhesive U-profile strip made of recycled material, with integrated pipe holder for 9.9 x 1.1 mm Uponor PE-Xa pipes. Length of track: 2.5 m Width of track: 24 mm Space between pipe holders: 20 mm c/c Installation height with pipe: 13 mm h l b Item no. l [mm] w [mm] h [mm] d [mm] c/c [mm] Description unit 1005274 2500 24 13 10 20 Uponor clamp track 9.9 mm 25 m Uponor PE-Xa pipes PE-Xa pipe with an oxygen diffusion barrier manufactured from peroxide cross-linked polyethylene (PE-Xa) using the Engel method complying with e.g. preniso 15875 Plastics piping systems for hot and cold water installations - Cross-linked polyethylene with an oxygen diffusion barrier of EVOH (ethyl vinyl alcohol). Uponor pipes fulfil the requirements for oxygen diffusion resistance as per DIN 4726. Malfunction temperature 95 C. Design pressure 8,8 bar (at 70 C). Item no. d [mm] s [mm] l [m] V [l/m] Description unit 1033024 9.9 1.1 120 0.047 Uponor eval PE-Xa pipe 9.9x1.1 120 m 1033026 9.9 1.1 240 0.047 Uponor eval PE-Xa pipe 9.9x1.1 240 m 1033025 9.9 1.1 480 0.047 Uponor eval PE-Xa pipe 9.9x1.1 480 m Uponor PE-Xa pipes PE-Xa pipe with an oxygen diffusion barrier manufactured from peroxide cross-linked polyethylene (PE-Xa) using the Engel method complying with e.g. preniso 15875 Plastics piping systems for hot and cold water installations - Cross-linked polyethylene with an oxygen diffusion barrier of EVOH (ethyl vinyl alcohol). Uponor pipes fulfil the requirements for oxygen diffusion resistance as per DIN 4726. Malfunction temperature 95 C. Design pressure 8,8 bar (at 70 C). Item no. d [mm] s [mm] l [m] V [l/m] Description unit Uponor pe PE-Xa Q&E pipe 20x2.0 1009228 20 2.0 120 0.2 120 m coil 120 m Uponor pe PE-Xa Q&E pipe 20x2.0 1009230 20 2.0 240 0.2 240 m coil 240 m Uponor pe PE-Xa Q&E pipe 20x2.0 1009231 20 2.0 480 0.2 480 m coil 480 m Uponor PE-Xa Q&E coupling 9.9 For Uponor PE-Xa pipe 9.9 x 1.1 mm, consisting of: - 1 coupling - 2 PEX Q&E rings for secure connection Material: Coupling made in brass; PEX Q&E rings made in high-pressure cross-linked polyethylene Item no. d [mm] s [mm] l [mm] z [mm] Description unit Uponor PE-Xa Q&E coupling 9.9-9.9 1005264 9.9 1.1 34 4 with two PEX rings 10 pcs 36 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor Plaster Ceiling Cooling Uponor Plaster Wall/Ceiling H/C - System components and accessories Uponor PE-Xa Q&E jointing reducer 20x9.9 For connection of Uponor PE-Xa pipes, made of brass. Item no. d [mm] d1 [mm] Description unit Uponor PE-Xa Q&E jointing reducer 20 x 9.9 1020518 9.9 20 incl. 1 PEX ring 9.9 and 1 PEX ring 20 5 pcs Uponor PE-Xa Q&E tee reducer 20x9.9x20 For connection of Uponor PE-Xa pipes, made of brass. Item no. d [mm] d1 [mm] d2 [mm] Description unit Uponor PE-Xa Q&E tee reducer 20 X 9.9 X 9.9 1020524 20 9.9 20 incl. 1 PEX ring 9.9 and 2 PEX rings 20 5 pcs Uponor PE-Xa conversion nipple For Uponor PE-Xa pipes 9.9 x 1.1 mm, made of brass. Item no. d [mm] MT ["] l [mm] z [mm] A/F [mm] Description unit Uponor PE-Xa conversion nipple 1005265 9.9 R 1/2 39 14 22 9.9-1/2 with one PEX ring 10 pcs Uponor Q&E Ring natural Made of PE-X. Uponor rings natural intended for Uponor Q&E fittings. Item no. d [mm] colour [-] Description unit Uponor Q&E Ring eval with stop edge 1042837 20 natural nature 20 20 pcs Uponor PE-X ring for PE-Xa pipes For Uponor Minitec PE-Xa pipe 9.9 x 1.1 mm; to secure fixing to Minitec fittings Material: High-pressure cross-linked polyethylene (PE-Xa) Item no. d [mm] Description unit Uponor PE-X ring for PE-Xa pipes 1005263 9.9 9.9 x 1.1 10 pcs EEI-Int-RHC-01.12 37

Uponor Radiant Heating/Cooling > Uponor heat emission plate Uponor heat emission plate Uponor heat emission plate 17mm Made of aluminium for use with timber suspended floors, with joists at 200mm centres. For support of Uponor PE-Xa pipes 17x2mm. Item no. l [mm] w [mm] Description unit Uponor heat emission plate 17 mm 1009129 1150 190 1150 x 190 mm 60 pcs Uponor heat emission plate 20mm Made of aluminium for use with timber suspended floors, with joists at 300mm centres. For support of Uponor PE-Xa pipes 20x2mm. Each pack of 40 plates covers 16m² (based on 80% floor coverage). Item no. l [mm] w [mm] Description unit Uponor heat emission plate 20 mm 1009132 1150 280 1150 x 280 mm 40 pcs 38 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor underfloor heating accessories Uponor under oor heating accessories Uponor edging strip 150x8 Edging strip conforming to DIN 18560, made of polyethylene with selfadhesive strip on outer face provides tight seal between edging strip and insulation. Length of roll: 50 m Item no. h [mm] s [mm] l [m] Description unit 1000079 150 8 50 Uponor edging strip 150x8 in length of 50 m 200 m Uponor edging strip 150x10 For installation between screed and adjacent building parts for floor constructions according to DIN 18560 and DIN EN 1264; with multiple tear perforation, laminated PE foil, self-adhesive sealing strips, particularly suitable for self-levelling screeds; bottom side adhesive for attachment to wall and exact installation in wall corners Material: Closed-cell polyethylene PE-LD Building material class: B2 Colour: blue Item no. h [mm] s [mm] l [m] colour [-] Description unit 1000080 150 10 50 blue Uponor edging strip 150x10 in length of 50 m 200 m Uponor joint profile 100x10 Self-adhesive clamp-on profile element made of hard PVC with polyethylene foam expansion strip, 10 mm thick, for the reliable separation of screed sections (e.g. in doorways), and to absorb expansion of screed. For expansion joints as per DIN 18560-2. Height: 100 mm Material thickness: 10 mm Length: 2 m Item no. h [mm] s [mm] l [m] Description unit 1000081 100 10 2 Uponor joint profile/self-adhesive strip length 2 m, height 100mm, thickness 10mm 30 m Uponor joint protection 20mm Made of PE-LD, with slit opening, for protection of pipes up to 20 mm in areas of expansion joints. Length: 300 mm Item no. l [mm] w [mm] s [mm] Description unit 1000082 300 80 5 Uponor joint protection tube for pipes up to 20 mm 30 pcs EEI-Int-RHC-01.12 39

Uponor Radiant Heating/Cooling > Uponor underfloor heating accessories Uponor under oor heating accessories Uponor joint protection 9.9mm Made of PE-LD, with slit opening, for protection of pipes up to 9.9 mm in areas of expansion joints. Length: 300 mm b l s Item no. l [mm] s [mm] w [mm] Description unit 1005269 300 2 35 Uponor joint protection tube for PE-Xa pipes 9.9 x 1.1, length 300 mm 30 pcs Uponor PE foil 0.2mm For installation on Uponor insulation or on standardised insulating material approved for the intended purpose for areas without stud foil. Prevents screed penetrating the underlying insulation. Dimensions: 4 m x 2.5 m Thickness: 0.2 mm Item no. l [m] w [m] s [mm] Description unit 1005049 60 1.25 ~0.2 Uponor PE foil 0.2 mm thickness 60 x 1.25 m 75 m² Uponor foil plug For fixing the foil on insulation. Lenght: 25 mm Item no. l [mm] Description unit 1000016 25 Uponor foil plug l=25mm 100 pcs Uponor marking kit For the marking of a measuring point for dampness measurement in screed, with red marker end. The marker is secured according to DIN 18560 with adhesive tape to the cover layer. The cover layer is not destroyed by the marker. A minimum distance from the measuring point to the nearest heating pipe of 10 cm must be observed. Material requirement: 1 marker per room; for areas larger than 50 m2, more markers are required. Material: Rubber round rod; base made in plastic, with adhesive strip Item no. h [mm] Description unit 1000083 100 Uponor marking set height 100 mm 10 pcs Uponor screed additive VD 450 For use as screed and mortar bed additive; improves screed quality thanks to enhanced plasticization and better water retention. Do not use in conjunction with levelling or anhydrite screed! Use for 7 cm screed thickness: approx. 0.2 l/m2 Minimum screed covering: 30 mm at 2 kn/m2 or 45 mm at 5 kn/m2 in conjunction with Uponor insulation/system board for 5 kn/m2 Curing time: 21 days Item no. DT [d] Con. [l/m²] Description unit 1000084 21 approx. 0.2 Uponor screed additive for better heat conductivity, type VD 450 20 l 40 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor underfloor heating accessories Uponor under oor heating accessories Uponor screed additive VD 550 For use as screed and mortar bed additive; improves screed quality thanks to enhanced plasticization and better water retention. VD 550 N also ensures that the screed dries faster ((high early strength). Do not use in conjunction with levelling or anhydrite screed! Use for 7 cm screed thickness: approx. 0.2 l/m2 Minimum screed covering: 30 mm at 2 kn/m2 or 45 mm at 5 kn/m2 in conjunction with Uponor insulation/system board for 5 kn/m2 Curing time: 8 days Item no. DT [d] Con. [l/m²] Description unit 1000085 8 approx. 0.2 Uponor screed additive for faster drying VD 550 N 25 l Uponor NF anti-freeze agent Ethylene glycol-based anti-freeze agent, for use as additive in radiant heating systems with Uponor pipes and standard heating system sealing materials. Vol. concentration to -20 C: 35% Vol. concentration to -25 C: 40% Vol. concentration to -30 C: 45% Water volume in pipes (for calculation of mixing ratio): 14 x 2: 0.079 l/m 17 x 2: 0.13 l/m 20 x 2.3: 0.19 l/m 25 x 2.3: 0.33 l/m 1005066 Uponor antifreezer up to - 30 C type NF 20 l EEI-Int-RHC-01.12 41

Uponor Radiant Heating/Cooling > Uponor underfloor heating manifolds Uponor modular plastic manifold Number Item no. Item no. L loops A B [mm] A With balancing screw B With flow meter 3 1030580 1030583 150 4 1030581 1035084 200 6 1030582 1030585 300 1009215 1005605 (230 V) 1000138 (24 V) 1042471 1042420 1009217 1032702 1009214 1034524 1005100 1005233 14x2 1005168 16x2 1005169 17x2 1005170 20x2 1005171 1006288 1009209 (Uponor plastic manifold Basic Kit) Manifold loops 2 3 4 5 6 7 8 9 10 11 12 1042420 Uponor plastic manifold single segment 2 1 1 1030580 Uponor plastic manifold 3 way 1 1 1 1030581 Uponor plastic manifold 4 way 1 1 1 2 1 1 1030582 Uponor plastic manifold 6 way 1 1 1 1 2 1009209 Uponor plastic manifold basic kit 1 1 1 1 1 1 1 1 1 1 1 42 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor underfloor heating manifolds Uponor modular plastic manifolds Uponor modular plastic manifold with balancing screw Pack includes supply and return manifolds made of fibreglass reinforced polyamid. Heating loop connections 3/4 MT euro-cone compatible with Uponor compression adapters. Spacing of individual outlets 50 mm. Manifolds can be joined to make the required number of ports. Uponor actuators can be mounted on the return manifold. In each flow manifold there are balancing valves for adjusting the supply in each loop. Max. operating temperature: 60 C; Max. operating pressure: 6 bar. Item no. outlets [-] l [mm] Description unit 1030580 3 150 Uponor modular plastic manifold with balancing srew, 3 way 1030581 4 200 Uponor modular plastic manifold with balancing srew, 4 way 1030582 6 300 Uponor modular plastic manifold with balancing srew, 6 way Uponor modular plastic manifold with flow meter Pack includes supply and return manifolds made of fibreglass reinforced polyamid. Heating loop connections 3/4 MT euro-cone compatible with Uponor compression adapters. Spacing of individual outlets 50 mm. Manifolds can be joined to make the required number of ports. Uponor actuators can be mounted on the return manifold. Supply manifold with adjustable and shut-off inserts (flow meter inspection window with scale of 0 4 l/min) for flow adjustment of individual heating loops. Max. operating temperature: 60 C; Max. operating pressure: 6 bar. Item no. outlets [-] l [mm] Description unit 1030583 3 150 Uponor modular plastic manifold with flow meter, 3 way 1030584 4 200 Uponor modular plastic manifold with flow meter, 4 way 1030585 6 300 Uponor modular plastic manifold with flow meter, 6 way Uponor accessories for plastic manifolds Uponor plastic manifold single segment set For Uponor plastic manifold with balancing screw for additional heating loop extension. Supply segment with regulating valve, return segment with thermostat upper section incl. cap for locking. Made of fibreglass reinforced polyamid. Max. operating temperature: 60 C; Max. operating pressure: 6 bar. Item no. MT ["] Description unit 1042420 G 3/4 Uponor plastic manifold single segment set with balancing screw 1 set Uponor plastic manifold single segment set with topmeter For Uponor modular plastic manifold with topmeter for additional heating loop extension. Supply segment with adjustable and shut-off inserts (topmeter inspection window with scale of 0 4 l/min) for flow adjustment of individual heating loops. Return segment with thermostat upper section incl. cap for locking. Made of fibre-glass reinforced polyamid. Max. operating temperature: 60 C; Max. operating pressure: 6 bar. Item no. MT ["] Description unit 1042471 G 3/4 Uponor plastic manifold single segment with flow meter 1 set EEI-Int-RHC-01.12 43

Uponor Radiant Heating/Cooling > Uponor underfloor heating manifolds Uponor accessories for plastic manifolds Uponor plastic manifold basic kit For Uponor modular plastic manifold including brackets, flat sealing screw connection pieces with swivel nut, thermometer and end pieces with air vent, filling and draining tap and a by-pass. Item no. l [mm] Description unit 1009209 150 Uponor Plastic manifold Basic kit G1" 1 set Uponor plastic manifold elbow connection set For connection of supply/return pipes to Uponor modular plastic manifold from the bottom. Made of fibreglass reinforced polyamid. Max. operating temperature: 60 C; Max. operating pressure: 6 bar. 1032702 Uponor plastic manifold elbow connection set for connection from below 1 set Uponor hose connection for plastic manifold For connection of refill/drainage hose 1/2" to Uponor plastic manifold. 1009214 Uponor hose connection for plastic manifold to refill and drainage valve 1 set Uponor plastic manifold retaining ring set For connection of Uponor plastic manifold single segments to the manifold in case of heating loop connection from top and bottom. 1009215 Uponor plastic manifold retaining ring set 1 set Uponor flow meter for plastic manifold For adjusting the water quantity of the individual heating loops in a range of 0-4 l/min. Water quantity is indicated in the inspection window. With shut-off function. Made of fibre-glass reinforced polyamid. 1009217 Uponor flow meter 0-4l/min for Uponor plastic manifolds 44 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor underfloor heating manifolds Uponor stainless steel manifolds Uponor stainless steel manifold with flow meter Manifold bar with flat-sealing screw connection and 1" FT with flat gasket, one side with air vent, filling and drain tap, revolvable for pipe connection and a 3/4" stop at the end. Heating loop connections 3/4" MT eurocone according to DIN V 3838 compatible with all Uponor compression adapters eurocone. Spacing of individual outlets 50 mm. Supply manifold with adjustable and shut-off inserts (flow meter inspection window with scale of 0 4 l/min) for flow adjustment of individual heating loops. Return manifold with valves incl. cap for locking. Uponor actuators can be screwed directly on the return valves. Fastener with sound-absorbing element included. Without ball valves and Uponor compression adapters. Made of stainless steel. Max. operating temperature: 60 C Max. operating pressure: 6 bar. Item no. outlets [-] l [mm] Description unit 1013051 2 195 Uponor stainless steel UFH-manifold 1" with flow meter, 2 way 1013052 3 245 Uponor stainless steel UFH-manifold 1" with flow meter, 3 way 1013053 4 295 Uponor stainless steel UFH-manifold 1" with flow meter, 4 way 1013054 5 345 Uponor stainless steel UFH-manifold 1" with flow meter, 5 way 1013055 6 395 Uponor stainless steel UFH-manifold 1" with flow meter, 6 way 1013056 7 445 Uponor stainless steel UFH-manifold 1" with flow meter, 7 way 1013057 8 495 Uponor stainless steel UFH-manifold 1" with flow meter, 8 way 1013058 9 545 Uponor stainless steel UFH-manifold 1" with flow meter, 9 way 1013059 10 595 Uponor stainless steel UFH-manifold 1" with flow meter, 10 way 1013060 11 645 Uponor stainless steel UFH-manifold 1" with flow meter, 11 way 1013061 12 695 Uponor stainless steel UFH-manifold 1" with flow meter, 12 way Uponor stainless steel manifold with balancing screw Manifold bar with flat-sealing screw connection and 1" FT with flat gasket, one side with air vent, filling and drain tap, revolvable for pipe connection and a 3/4" stop at the end. Heating loop connections 3/4" MT eurocone according to DIN V 3838 compatible with all Uponor compression adapters eurocone. Spacing of individual outlets 50 mm. Supply manifold with control valves, manual screws for preadjustment of valves by an allen key. Return manifold with valves incl. cap for locking. Uponor actuators can be screwed directly on the return valves. Fastener with sound-absorbing element included. Without ball valves and Uponor compression adapters. Made of stainless steel. Max. operating temperature: 60 C Max. operating pressure: 6 bar. Item no. outlets [-] l [mm] Description unit 1013062 2 195 Uponor stainless steel UFH-manifold 1" with balancing screw, 2 way 1013063 3 245 Uponor stainless steel UFH-manifold 1" with balancing screw, 3 way 1013064 4 295 Uponor stainless steel UFH-manifold 1" with balancing screw, 4 way 1013065 5 345 Uponor stainless steel UFH-manifold 1" with balancing screw, 5 way 1013066 6 395 Uponor stainless steel UFH-manifold 1" with balancing screw, 6 way 1013067 7 445 Uponor stainless steel UFH-manifold 1" with balancing screw, 7 way 1013068 8 495 Uponor stainless steel UFH-manifold 1" with balancing screw, 8 way 1013069 9 545 Uponor stainless steel UFH-manifold 1" with balancing screw, 9 way 1013070 10 595 Uponor stainless steel UFH-manifold 1" with balancing screw, 10 way 1013071 11 645 Uponor stainless steel UFH-manifold 1" with balancing screw, 11 way 1013072 12 695 Uponor stainless steel UFH-manifold 1" with balancing screw, 12 way EEI-Int-RHC-01.12 45

Uponor Radiant Heating/Cooling > Uponor underfloor heating manifolds Uponor manifold accessories Uponor plastic manifold connection valve kit For the hydraulic balancing and shut-off of the Uponor plastic manifold, consisting of: - G 1/Rp 1 inlet control valve for the hydraulic balancing and independent shutt-off of the manifold, including hand wheel and display for settings/ closing kvs value: 5.4 m3/h - G 1/Rp 1 return valve for the shut-off of the manifold, including hand wheel and display for closing; adaptable for Uponor plastic manifold actuators. kvs value: 6.4 m3/h In conjunction with Uponor plastic manifold actuators, the kvs value is 4.8 m3/h. The connecting valve can be used to control individual zones. Material: Housing made in brass, hand wheels made in polyamide Max. testy pressure: 10 bar (water) Item no. l [mm] h1 [mm] z [mm] MT ["] FT ["] A/F [mm] Description unit 1005100 80 50 45 G 1 Rp 1 38 Uponor plastic manifold connection valve G-1/Rp 1 1 set Uponor ball valve Made of plated brass. With flat-sealing vertical screw connection 1 MT. Length: 60 mm. 1032701 Uponor ball valve 1 MT x 1 FT flat sealing 1 set Uponor coupling nipple Made of tin-plated brass. Male thread acc.to DIN EN ISO 228-1. Item no. MT ["] Description unit 1006641 3/4 Uponor eurocone nipple MLC 3/4MT-3/4MT 10 pcs Uponor pipe connection PE-Xa 9.9 For connection of Uponor PE-Xa pipes 9.9 x 1.1 mm to Uponor manifolds and Uponor connection box, made of brass. l d IG SW Item no. d [mm] FT ["] l [mm] A/F [mm] Description unit 1005266 9.9 G 3/4 39 30 Uponor PE-Xa pipe connection 9.9-3/4 FT eurocone and one PE-X ring 10 pcs 46 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor underfloor heating manifolds Uponor manifold accessories Uponor compression adapter Compression adapter made of brass, for connection of Uponor PE-Xa pipes to manifolds. Female thread 3/4"" eurocone acc. to DIN EN ISO 228-1. Material: Brass Item no. d [mm] s [mm] FT ["] A/F [mm] Description unit 1005168 14 2.0 G 3/4 30 Uponor PE-Xa compression adapter with eurocone, 14x2.0 x 3/4 FT 10 pcs 1057368 16 1.8/2.0 G 3/4 30 Uponor PE-Xa compression adapter with eurocone, 16x1.8/2.0 x 3/4 FT 10 pcs 1005170 17 2.0 G 3/4 30 Uponor PE-Xa compression adapter with eurocone, 17x2.0 x 3/4 FT 10 pcs 1057370 20 1.9/2.0 G 3/4 30 Uponor PE-Xa compression adapter with eurocone, 20x1.9/2.0x3/4 FT 10 pcs 18 5 Uponor plated compression adapter Made of plated brass, for connection of Uponor PE-Xa pipes to manifolds. Female thread 3/4" eurocone acc. to DIN EN ISO 228-1. d IG SW Item no. d [mm] FT ["] A/F [mm] p [bar] Description unit 1057441 16 G 3/4 30 6 Uponor compression adapter S5.0 16x1.8/2.0x3/4 Eurocone plated 10 pcs 1057442 20 G 3/4 30 6 Uponor compression adapter S5.0 20x1.9/2.0x3/4 Eurocone plated 10 pcs Uponor compression adapter MLC 3/4" eurocone Compression adapter made of brass, union nut and inner sleeve plated. For connection of Uponor MLC pipes to manifolds (eg. Uponor manifold H). Female thread 3/4" eurocone according to DIN EN ISO 228-1. Test safety and no bevelling. Item no. d [mm] FT ["] Description unit 1058089 14 3/4 Uponor compression adapter MLC 14-3/4FT eurocone metal version 1058090 16 3/4 Uponor compression adapter MLC 16-3/4FT eurocone metal version 1058091 18 3/4 Uponor compression adapter MLC 18-3/4FT eurocone metal version 1058092 20 3/4 Uponor compression adapter MLC 20-3/4FT eurocone metal version Uponor manifold H cap Made of coated brass, with eurocone sealing insert. Item no. FT ["] Description unit 1014122 G 3/4 Uponor manifold H cap 3/4FT eurocone 10 pcs EEI-Int-RHC-01.12 47

Uponor Radiant Heating/Cooling > Uponor underfloor heating manifolds Uponor pipe bend support Uponor pipe bend support plastic Made of impact resistant plastic to support 90 bends. Item no. d [mm] Description unit 1047000 9.9 Uponor pipe bend support plastic 9.9 mm 50 pcs Uponor pipe bend support Made of galvanized steel as bend support for the pipes in the manifold area. Item no. d [mm] Description unit 1009004 16 Uponor pipe bend support 14-16 mm 50 pcs 1033975 17-18 Uponor pipe bend support 17-18 mm 50 pcs 1009233 20 Uponor pipe bend support 20 mm 50 pcs Uponor manifold cabinets Manifold cabinet concealed version For attachment of Uponor manifolds, Uponor controller and Uponor pump control stations on universal rail fixation incl. fixation set. Made of galvanized steel. All visible parts are powder coated in white colour (RAL 9010). Cabinet width (with frame): 555-950mm Cabinet installation depth: 120-180mm Cabinet installation high: 820-910mm Item no. w [mm] h [mm] Description 1046991 555 820-910 Uponor cabinet concealed version, UFH1 width 555mm, colour white 1046992 710 820-910 Uponor cabinet concealed version, UFH2 width 710mm, colour white 1046993 785 820-910 Uponor cabinet concealed version, UFH3 width 785mm, colour white 1046994 950 820-910 Uponor cabinet concealed version, UFH4 width 950mm, colour white 48 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor underfloor heating manifolds Uponor manifold cabinets Manifold cabinet on-wall version For attachment of Uponor manifolds, Uponor controller and Uponor pump control stations on universal rail fixation incl. fixation set. Made of galvanized steel. All visible parts are powder coated in white colour (RAL 9010). Cabinet width (with frame): 555-950mm Cabinet installation depth: 160mm Cabinet installation high: 820mm Item no. w [mm] h [mm] Description 1046996 555 820 Uponor cabinet on-wall version, UFH1 width 555mm, colour white 1046997 710 820 Uponor cabinet on-wall version, UFH2 width 710mm, colour white 1046998 785 820 Uponor cabinet on-wall version, UFH3 width 785mm, colour white 1046999 950 820 Uponor cabinet on-wall version, UFH4 width 950mm, colour white EEI-Int-RHC-01.12 49

Uponor Radiant Heating/Cooling > Uponor controls Uponor individual radio room temperature control with Dynamic Energy Management (DEM) The Uponor individual radio room temperature control system with DEM has been developed on the basis of the existing individual radio room temperature control. Apart from the colour of the controller (previously white, now grey), there are many more differences between the two versions. The advanced system comes with a range of features that make installation even easier. Apart from the great energy efficiency during operation, fast installation and user-friendly operation that are standard features of all Uponor systems, the new individual room temperature control makes heating and cooling even more comfortable. The automatic balancing function does away with time-consuming manual hydraulic balancing. In most cases, there is no need for recalculation of the valve settings, which is normally required after a change of the room layout or the floor covering. The heat distribution in the room is evaluated by a bespoke software solution. The relevant values are stored and the system is automatically balanced at regular intervals. This guarantees optimum energy distribution! The comfort setting prevents that heating surfaces become too cool when the room is heated with an alternative source (e.g. open fireplace). The supply diagnosis monitors the heat performance in all rooms and signals any insufficient or excess supply to the I-76 interface. The room bypass function is particularly suitable for systems with specific minimum flow requirements. Incorrectly assigned thermostats are automatically detected and rectified by the room check function. Uponor interface I-76 Item no. 1045568 20,5 Uponor radio thermostat T-75 Item no. 1000502 (white) Item no. 1000504 (silver) Item no. 1046114 (grey) 20,5 Uponor radio controller (consisting of controller and interface) Item no. 1045562 Uponor thermostat T-54 Item no. 1045572 Uponor radio controller C-56 (for system extension) Item no. 1045565 Uponor SMS-module R-56 Item no. 1045570 Your benefit Energy savings up to 12 % thanks to greater efficiency No need for manual hydraulic balancing High time saving during installation More accurate and faster control, up to 25% faster response time Higher comfort through improved heat distribution Easy to operate Reliable operation with minimum support No need for recalculation after change to heating circuit layout/size System not affected by subsequent change of floor covering Easy troubleshooting "Clean solution" for renovation Remote control via SMS connection possible Easy, well-tried handling Optional automatic switch over to heating-/ or cooling mode with the Uponor heating/cooling controller C-46 Operation of up to three controller C-56 from one interface I-76 50 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor controls Uponor Radio control Uponor controller with interface C-56+I-76 radio For receiving and transforming of radio signals from the thermostats, with integrated DEM functions consisting of: Controller C-56 with - Electronic control - Reception of max. 12 room-thermostats - Connection of max. 14 actuators 24 Volt - Heating/Cooling function switched by external contact - Pump relay - Valve exercise, pump exercise Interface I-76 with - Display, back lighted, new look, blue full dot matrix - Menu in English, Integrated functions: - Five temperature setback progams, - Max/min temperature limitations, - Holiday temperature - Automatic summer/wintertime change - Auto adapt function - Room check function - Room bypass function - The Interface can control up to 3 controllers Accessories External Antenna, cables for connections, mounting material Mark of conformity: CE Operational voltage: 230 V / 50 Hz Max. power input per actuator: 0,2 A Protection class: IP 30 (EN 60 529) Colour: grey (RAL 7015) Item no. OV [V] P [W] EP/a [W] colour [-] Description unit 1045562 230 1 >2 grey Uponor controller with interface C-56+I-76 radio, grey 1 set 24 V 50 20 Uponor controller C-56 radio For receiving and transforming of radio signals from the thermostats, to use the DEM function with the I-76. consisting of: Controller C-56 with - Electronic control - Reception of max. 12 room-thermostats - Connection of max. 14 actuators 24 Volt - Heating/Cooling function switched by external contact - Pump relay - Valve exercise, pump exercise - Plastic color grey (RAL 7015) - Protection rating IP 30 Accessories External Antenna, cables for connections, mounting material 316 60 110 Item no. OV [V] P [W] EP/a [W] colour [-] Description unit 1045565 230 1 >2 grey Uponor controller C-56 radio grey EEI-Int-RHC-01.12 51

Uponor Radiant Heating/Cooling > Uponor controls Uponor Radio control Uponor interface I-76 For combination with the controller C-56 to use the DEM function Interface I-76 with - Display, back lighted, new look, blue full dot matrix - Menu in English, Integrated functions: - Five temperature setback progams, - Max/min temperature limitations, - Holiday modus - Automatic summer/wintertime change - Auto adapt function - Room check function - Room bypass function - For controling of up to 3 controllers Protection class: IP 30 (EN 60 529) Colour: grey (RAL 7015) Item no. l [mm] w [mm] h [mm] Description unit 1045568 110 110 30 Uponor interface I-76 grey Uponor thermostat display T-75 radio Designed as a wireless single room temperature sensor, measuring the perceived room temperature and transmitting the values to the wireless base unit or wireless control module, with display showing the set and measured room temperature, consisting of: Housing with - Temperature programming buttons - Control electronics Signal range: max. 30 m Signal frequency: 868 MHz Power supply: Alkaline battery, service life approx. 5 years, size AAA Transmission power: approx. 1 mw Set temperature range: 5-30 C Colour: pure white (near RAL 9010) or silver (near RAL 9006) Item no. l [mm] w [mm] h [mm] colour [-] Description unit 1000502 124 66 16 white Uponor thermostat display T-75 radio white 1000504 124 66 16 silver Uponor thermostat display T-75 radio silver 1046114 124 66 16 grey Uponor thermostat display T-75 radio grey Uponor thermostat mounting kit Accessory for wireless room sensor; use this kit to position and/or secure the room sensor anywhere in the room on the wall; with removal/child safety device, consisting of: - Mounting plate with clip - Bracket - Adhesive pads for fixture to smooth surfaces (tiles, etc.) Colour: pure white (near RAL 9010) or silver (near RAL 9006) or grey Item no. colour [-] Description unit 1000503 white Uponor thermostat mounting kit for T-75 radio, white 1000505 silver Uponor thermostat mounting kit for T-75 radio, silver 1046115 grey Uponor thermostat mounting kit for T-75 radio, grey 52 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor controls Uponor Radio control Uponor thermostat T-55 radio Radio thermostat, including batteries and screws for mounting. Operating distance: max. 30 m. Set point range 6 30 C. Item no. l [mm] w [mm] h [mm] Description unit 1000527 72 72 21 Uponor thermostat T-55 Radio Uponor thermostat public T-54 Radio thermostat with inside setting, including batteries and screws for mounting. Operating distance: max. 30 m. Set point range 6 30 C. SMS module R-56 can be connected. Floor sensor for min/max limitation of floor temperature can be connected. Item no. l [mm] w [mm] h [mm] Description unit 1045572 72 72 21 Thermostat Public T-54 Radio Uponor SMS module R-56 For connection with the thermostat T-54, to activate and control the system settings and monitor the actual room temperature in a reference room via SMS. Item no. l [mm] w [mm] h [mm] Description unit 1045570 185 75 28 Uponor SMS module R-56 Uponor floor sensor Floor sensor for connection to the thermostats (radio and wired) with external input with sensor attached to 4m cable. Item no. d [mm] l [mm] l1 [mm] Description unit 1000538 5 4000 25 Uponor floor sensor for T-33, T-37 EEI-Int-RHC-01.12 53

Uponor Radiant Heating/Cooling > Uponor controls Uponor outdoor sensor Uponor outdoor sensor Outdoor sensor for connection to the Thermostats with external input with Sensor box and seperate 5 m cable Has to be connected to thermostat T-54 in a system with Interface I-76 to display outdoor temperature. - IP65 - Plastic color 7035 Item no. colour [-] Description unit 1000529 light grey Uponor outdoor sensor for T-33, T-37, T-53 Uponor installation cable Twisted pairs cable to connect: - Interface to Controller - Controller to Controller - Extension for Antenna cable Item no. l [m] Description unit 1000515 15 Uponor installation cable 15m Uponor repeater To solve problems with radio transmission, for on-wall mounting. Item no. OV [V] P [W] l [mm] w [mm] h [mm] Description unit 1000518 230 < 1 160 75 26 Uponor repeater 230 V Uponor KNX media coupler R-76 can connected the C-56 Radio to a standard KNX bus. This device will act as a interface between the C-56 Radio and the KNX wired bus. Conformity: CE Protection Class: IP 30 Item no. l [mm] w [mm] h [mm] Description unit 1045571 203 75 26.5 KNX Media Coupler R-76 54 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor controls Uponor 24 V individual room climate control system Wired individual room temperature control system with wide range of components. The Uponor 24 V individual room climate control system consists of electronic components that have been specially devised for combination with each other (3 thermostat models, 2 controllers and optional timer). As soon as a thermostat detects that heating or cooling in a room must be adjusted, the controller operates the 24 V thermo drives accordingly. The three thermostat models available for this system can be freely combined with each other and are connected to the controllers through non-polarity 2-core cables (6-12 V) that cannot be confused. Choose between two controller types Depending on the size of the heating system and the specific requirements, you can install a 6-channel (C-33) or 12-channel (C-35) controller. The 12-channel controller caters for maximum 12 thermostats and 14 thermal actuators plus an optional timer I-36. The 12-channel C-35 controller also provides the option to switch over between heating and cooling. The device is wired in such a way that several thermal actuators can be combined with a single thermostat without the need for wired bridges. Thermostats and thermal actuators are connected to the controller through easy-to-use plug-in wiring terminals. Important: The Uponor 24 V individual room climate control system is a stand-alone system of tailor-made components that cannot be replaced with third-party devices. Your benefit Low-cost and safe thermostat wiring (6-12 V) Choice of three thermostat models Connection of optional floor sensors Room temperature lowering with Uponor timer and two timer zones Optional limitation of set point temperature settings Also suitable for surface cooling systems with dew point monitoring Optional automatic switching over between heating/ cooling with Uponor heating/cooling controller C-46 EEI-Int-RHC-01.12 55

Uponor Radiant Heating/Cooling > Uponor controls Uponor wired control Uponor controller C-33, 6 channels Controller C-33 with electronic control, connection of max. 6 Thermostats, connection of max. 8 actuators 24 Volt, pump relay, pump / valve exercise, power LED, plastic color RAL 9010, protection rating IP 30, accessories, mounting material. Item no. OV [V] l [mm] w [mm] h [mm] Description unit 1000531 24 315 110 58 Uponor controller, 6 channels C-33 wired Uponor controller C-35, 12 channels For the power supply of max. 12 room sensors (models T-33,T-35, T-37) and max. 14 thermo drives (models TA/TR),24 V. Preassembled unit, consisting of: - Housing including mounting accessories - Control electronics with microprocessor - Pump logics - Valve interval - Overload protection - Connecting cable with Euro standard plug - Floating heating/cooling switching by external signal - Connection port for Uponor I-35 timer with 2 temperature lowering programs and for Uponor dew point converter Conformity: CE Colour: pure white (near RAL 9010) Protection class: IP 30 (EN 60529) Max. power consumption per TA 24: 0.2 A (switching peak) Effective power per TA 24: <2 W Item no. OV [V] l [mm] w [mm] h [mm] Description unit 1000533 24 315 110 58 Uponor controller, 12 channels C-35 wired Uponor Thermostat T-34 Wired flush mounted thermostat for room temperature control Consisting of: - Flush thermostat T34 with - Dial for settings - Sensor for air temperature - LED for indication - Two wires - Plastic color RAL 9010 General functions - Setpoint range 6-30 C - Setting range can be limited mechanically by moving pins under the dial Item no. l [mm] w [mm] h [mm] Description unit 1048010 81 81 14.7 Uponor thermostat flush T-34 wired 56 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor controls Uponor wired control Uponor thermostat T-35 For connection to Uponor controller C-33 or C-35 with: - Dial for settings - Sensor for air temperature - LED for indication - Two wires - Plastic color RAL 9010 Functions - Setpoint range 6-30 C, mark at 21 C - Setting range can be limited mechanically by moving pins under the dial Item no. l [mm] w [mm] h [mm] Description unit 1000535 72 72 21 Uponor thermostat T-35 wired Uponor thermostat T-37 for external sensor For connection to Uponor controller C-33 or C-35 with: - Dial for settings - Sensor for air temperature - LED for indication - Terminal for Floor Sensor - Two wires - Plastic color RAL 9010 Functions - Setpoint range 6-30 C, mark at 21 C - Setting range can be limited mechanically by moving pins under the dial - Internal setting for the Floor Senor, range print on circuit board Item no. l [mm] w [mm] h [mm] Description unit 1000536 72 72 21 Uponor thermostat f. external sensor T-37 wired Uponor wall frame Wall frame to cover standard wall boxes or in case of renovation shades of old thermostats, size 90*90, plastic color RAL 9010 Item no. l [mm] w [mm] h [mm] Description unit 1000539 90 90 8 Uponor wall frame for T-33, T-35, T-37 EEI-Int-RHC-01.12 57

Uponor Radiant Heating/Cooling > Uponor controls Uponor wired control Uponor digital thermostat T-36 Consisting of: - Digital thermostat T36 Options: - Floor sensor (1000538) (sold seperately) General functions - Room temperature regulation with internal sensor - Room or remote temperature display - Room temperature, Room and max/min floor temp (heating/cooling), remote sensor regulation selectable. - Automatic or Manual balancing - Comfort / ECO mode. - Lock indication - Standby/OFF mode - Modes displayed on LCD: Heating, Cooling, ECO, Lock, Standby, Comfort/ECO, Auto/Man balancing. - Displayed temperature calibration - Window open function - 3 button keyboard +/-/OK - Hidden reset Item no. l [mm] w [mm] h [mm] Description unit 1048011 85 83 25 Uponor digital thermostat T-36 wired Uponor programmable digital thermostat T-38 Consisting of: - Programmable digital thermostat T38 Options: - Floor sensor (1000538) (sold seperately) General functions - Room or remote temperature display. - Room temperature, Room and max/min floor temp (heating/cooling), remote sensor regulation selectable. - Automatic or Manual balancing - Comfort / ECO mode. - Lock indication. - Standby/OFF mode - 4 Pre pre-recorded modifiable programs for working days / week-end / week - Date and time, with summer/winter change, power failure proof - Hidden reset - Temporary or permanent override mode - Modes displayed on LCD: Heating, Cooling, Lock, Standby, Holiday, Comfort/ECO - Displayed temperature calibration - Window open function - Powered by base unit (no batteries) Item no. l [mm] w [mm] h [mm] Description unit 1048012 85 83 25 Uponor programmable digital thermostat T-38 wired 58 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor controls Uponor wired control Uponor thermostat Public T-33 For connection to Uponor controller C-33 or C-35 with: - Plain cover - Internal setting - Sensor for air temperature - Terminal for Floor Sensor - Two wires - Plastic color RAL 9010 Functions - Setpoint range 6-30 C, mark at 21 C - Internal setting for the Floor Senor - Room sensor - Max/min limitation with floor sensor Item no. l [mm] w [mm] h [mm] Description unit 1000537 72 72 21 Uponor thermostat public T-33 wired Uponor timer I-36 Consisting of: - Programmable digital timer I36 General functions - 2 zones programming comfort / ECO - Display of zone status and time - Pre-recorded modifiable programs for working days / week-end / week - Date and time, with summer/winter change, power failure proof - Lock mode, standby OFF mode - Hidden reset - Temporary or permanent override mode - Dry contact input for forced ECO mode. - Example: Signal from Uponor R-56 SMS module for remote control - Powered by base unit (no batteries) Item no. l [mm] w [mm] h [mm] Description unit 1048013 85 83 25 Uponor timer I-36 for C-35 Uponor control accessories 24 V Uponor actuator 24V 24 V, with open/closed indicator, suitable for use with Uponor plastic manifolds in connection with Uponor radio or wired control system. Closes when idle. With all-round shower protection (IP 54). Suitable for operation at ambient temperature of up to 60 C. Threaded connector M 30 x 1.5 mm MT. Height: 54 mm. Item no. MT [-] d [mm] h [mm] OV [V] P [W] Description unit 1000138 30x1.5 40 54 24 < 2 Uponor actuator 24V for plastic manifold, 30 x 1,5 MT Uponor actuator 24V 24 V, with open/closed indicator, suitable for use with Uponor stainless steel manifolds in connection with Uponor control system. Closes when idle. With all-round shower protection (IP 54). Suitable for operation at ambient temperature of up to 60 C. Threaded connector M 30 x 1.5 mm FT. Height: 56 mm Item no. FT m [-] d [mm] h [mm] OV [V] P [W] Description unit 1013008 30x1.5 40 56 24 ~ 2 Uponor actuator 24V for stainless steel manifold, 30 x 1,5 FT EEI-Int-RHC-01.12 59

Uponor Radiant Heating/Cooling > Uponor controls Uponor control accessories 24 V Uponor return temperature limiter For use in low-temperature range for combined underfloor/ radiator heating systems respectively wall-radiator heating systems for the regulation of the return temperature of small heating areas up to max. 15 m2. Consists of installation casing with cover, fast-action air vent valve, thermostat for return temperature limiting set between 25 and 65 C. Factory-made limitation of return temperature approx. 50 C. Suitable for Uponor compression adapter with 3/4" eurocone. Dimensions: (H x W x D) 150 x 122 x 65 mm D after installation: 5 mm 1013005 Uponor return temperature limiter Uponor wired control 230 V Uponor Controller C-23 Uponor Controller C-23 for wiring up to 6 room thermostats and max. 14 actuators. Up to 4 actuators per channel are possible. Optional: pump relay. IP43. Item no. l [mm] w [mm] h [mm] OV [V] Description unit 1058426 310 90 65 230 Uponor Controller C-23 230V, WIRED Uponor Pump Relay for Controller C-23 Pump relay for C-23 6 room Controller Item no. l [mm] w [mm] Description unit 1058427 310 90 Uponor Pump Relay for Controller C-23 230V, WIRED Uponor Thermostat T-23 Standard Thermostat 230 V, with on/off contact 1058422 Uponor Thermostat T-23 230V, WIRED Uponor Thermostat Flush T-24 Flush Mounted Thermostat 230 V. On/off contact, insulated cover, protective cap, frame (neutral), 50 x 50 mm cover, pure white, glossy 1058423 Uponor Thermostat Flush T-24 230V, WIRED 60 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor controls Uponor wired control 230 V Uponor Thermostat H/C T-25 Heating/Cooling Thermostat 230 V with a change over contact for maximum 5 actuators and a heating / cooling switch. For 2 pipe installation, specially for heatpump. 1058424 Uponor Thermostat H/C T-25 230V, WIRED Uponor Thermostat Prog. Digital T-26 Digital Programmable Thermostat 230V. Energy saving feature calculates heat up time of system. Includes holiday mode, temporary over-ride and specified duration, 5/2 or 7 day programme, floor temperature control, lock facility, status display on current thermostat mode. 1058425 Uponor Thermostat Prog. Digital T-26 230V, WIRED Uponor control accessories 230 V Uponor actuator 230 V 230 V, with open/closed indicator, suitable for use with Uponor plastic manifolds. Closes when idle. With all-round shower protection (IP 54). Suitable for operation at ambient temperature of up to 60 C. Threaded connector M 30 x 1.5 mm MT. Height: 54 mm. Item no. MT [-] d [mm] h [mm] OV [V] P [W] Description unit 1005605 30x1.5 40 54 230 < 3 Uponor actuator 230V for plastic manifold, 30 x 1.5 MT Uponor actuator 230 V 230 V, with open/closed indicator, suitable for use with Uponor stainless steel manifolds. Closes when idle. With all-round shower protection (IP 54). Suitable for operation at ambient temperature of up to 60 C. Threaded connector M 30 x 1.5 mm FT. Height: 56 mm Item no. FT m [-] d [mm] h [mm] OV [V] P [W] Description unit 1013006 30x1.5 40 56 230 ~ 3 Uponor actuator 230V for stainless steel manifold, 30 x 1,5 FT EEI-Int-RHC-01.12 61

Uponor Radiant Heating/Cooling > Uponor controls Uponor Controls Heating-supply temperature control with radio individual room temperature control 3 2 2 3 4 4 9 9 4 3 1 2 x 0,5 mm 2 max. 20 m (je Verbindung) 8 7 2 x 0,4 mm 2 max. 50 m 9 6 6 5 M The diagram shows a simplified illustration of the key control components. For detailed instructions regarding the installation and operation of the system, refer to the manuals shipped with the components or download the relevant documents from www.uponor.com. Components 1 Radio controller C-56 with interface I-76 2 Radio controller C-56 3 Antenna 4 Wireless thermostat 5 Climate controller C-46 6 Supply/return sensor 7 Outdoor sensor 8 Manifold 9 heating source Functional description The wireless room temperature sensor measures the operative room temperature. Through the wireless controller, the thermal actuators and manifold valves, it controls the heat release from the respective room heating surface. The wireless basic control unit allows for individual room temperature control. It is thus for example possible to assign different temperature lowering times to different rooms. Together with the remote control system, the C-46 heating controller adjusts the supply temperature depending on the actual weather conditions and the programmed heating times. 62 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor controls heating/cooling - supply temperature control with automatic H/C switchover valve powerd by boiler and chiller 3 2 2 3 4 4 4 3 1 2 x 0,5 mm 2 max. 20 m (je Verbindung) 2 x 0,5 mm 2 max. 20 m 8 2 x 0,4 mm 2 max. 50 m 7 M 7 6 The diagram shows a simplified illustration of the key control components. For detailed instructions regarding the installation and operation of the system, refer to the manuals shipped with the components or download the relevant documents from www.uponor.com. 10 100 m (vom Elektrofachbetrieb zu prüfen) 9 Components 1 Radio controller C-56 with interface I-76 2 Radio controller C-56 3 Antenna 4 Wireless thermostat 5 H/C relay 6 Climate controller C-46 7 Supply/return sensor 8 Outdoor sensor 9 Chiller 10 Switch-over valve Functional description Depending on the outdoor and room temperature, the C-46 heating/cooling controller switches the switchover valve installed by the operator from the heating to the cooling source. The H/C switching module switches the C55/C56 wireless controller from heating to cooling mode, as the manifold valves must be opened as the room temperature increases (reverse operation of thermal actuators). For cooling, the relative air humidity in the room must also be measured, in addition to the room temperature. This is done through the humidity sensor H-56. It is important to prevent that the temper- ature drops below the dew point, as this would lead to condensation on cold system components. The C-46 heating/cooling controller regulates the cooling water supply temperature through the control valve to keep it above the dew point temperature. This ensures that the system components from the control valve downwards are protected against damage from condensation that tends to occur when the actual temperature drops below the dew point. Depending on the cooling water temperature, the system components from the chiller to the control valve must be insulated with diffusion-tight material. EEI-Int-RHC-01.12 63

Uponor Radiant Heating/Cooling > Uponor controls Uponor climate controller Uponor climate controller C-46 Weather compensator controlling supply water in heating. Can be integrated in the C-56 system via bus connection. Consisting of: - Climate Controller C-46 - Wired Outdoor sensor - Wired Supply sensor Options: - Antenna Module for connection to wireless Thermostats - Wired Indoor sensor - Wired Return sensor. General functions - Installation wizard gives easy and fast installation & set-up - Quick menu system gives easy access to basic settings - Integration with C-56 system via bus gives CC access to zone data from C-56. - System information, H/C-state, ECO-mode etc are also shared on the bus. - Automatic summer/wintertime change - ECO/Comfort timer in CC if no I-76 in the system. - Clock backup 8 hours - Alarm at disturbance - Pumpmanagement with internal fuse - Supports 24V Thermal Actuator or 0-10V controlled rotating mixer motor, or variable speed pump - General purpose input for Heating+Cooling switch or Snow detection - General purpose output for Heating+Cooling command or Dehumidification command or Error signalling - Input indoor sensor - Input outdoor sensor - Input Supply Sensor - Input Return Sensor Accessories Outdoor sensor (5m cable), Supply sensor (4m cable), mounting material Item no. l [mm] w [mm] h [mm] Description unit 1047844 174 106 80 Uponor climate controller C-46 64 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor controls Uponor climate controller Uponor climate controller C-46 extended Weather compensator controlling supply water in heating + cooling Can be integrated in the C-56 system via bus connection. Consisting of: - Climate Controller C-46 - Antenna - Wireless Humidity Sensor H-56 - Wired Outdoor sensor - Wired Supply sensor Options: - Wired Indoor sensor - Wired Return sensor - Additional 5 RH-sensors General functions - Installation wizard gives easy and fast installation & set-up - Quick menu system gives easy access to basic settings - Integration with C-56 system via bus gives CC access to zone data from C-56. - System information, H/C-state, ECO-mode etc are also shared on the bus. - Automatic summer/wintertime change - ECO/Comfort timer in CC if no I-76 in the system. - Clock backup 8 hours - Alarm at disturbance - Pumpmanagement with internal fuse - Supports 24V Thermal Actuator or 0-10V controlled rotating mixer motor, or variable speed pump - General purpose input for Heating+Cooling switch or Snow detection - General purpose output for Heating+Cooling command or Dehumidification command or Error signalling - Input indoor sensor - Input outdoor sensor - Input supply sensor - Input return sensor Humidity Sensor H-56: - Wireless RH sensor with battery alarm - incl Batteries and mounting kit - Connects to C-46 with antenna or via C-56 Accessories Outdoor sensor (5m cable), Supply sensor (4m cable), mounting material, 3m Antenna cable Item no. l [mm] w [mm] h [mm] Description unit 1047845 174 106 80 Uponor climate controller C-46 extended Uponor humidity sensor H-56 - Wireless RH sensor with battery alarm - incl Batteries and mounting kit - Connects to C-46 with antenna or via C-56 Item no. l [mm] w [mm] h [mm] Description unit 1047846 72 72 21 Uponor humidity sensor H-56 EEI-Int-RHC-01.12 65

Uponor Radiant Heating/Cooling > Uponor controls Uponor climate controller Uponor supply or return sensor for C-46 - For connection directly to C-46 - Sensor with 4m wire. Note: Return sensor only needed for average temperature control 1047847 Uponor supply or return sensor for C-46 Uponor outdoor or indoor sensor for C-46 - For connection directly to C-46 - Additional connection wire needed. 1047848 Uponor outdoor or indoor sensor Uponor relay H/C, 24 V For automatic heating/cooling switchover on external signal. Item no. OV [V] l [mm] w [mm] h [mm] Description unit 1000516 24 160 50 95 Uponor relay H/C 24 V 1000517 230 160 50 95 Uponor relay H/C 230 V Uponor Mixer Motor For mounting on a mixing valve and used in combination with the C-46. Externally powerd. 1002356 Uponor Mixer motor 24V with 0-10V signal 1002357 Uponor Mixer motor 230V / 3PT Uponor Wall Power Supply 230V/24V Power supply with Euro-plug for 0-10V controlled mixer motor. 1048763 Uponor Power supply 230V/24V for C-46 mixer motor 66 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor controls Uponor control stations for heating/cooling UFH systems Minitec Siccus Tecto Self attaching system Tacker & Clamp track Pipe positioning panel Classic Control stations RS2 Uponor room control station RS 2 up to 2 kw Unit set 6 Uponor constant temperature control unit set 6 up to 6 kw Push 23 Uponor pump group up to 10 kw MPG 10 Uponor pump group 3 to 10 kw with controller Unit set type 1 Uponor pump group up to 12 kw CPG 15 Uponor central pump group 3 to 15 kw with controller EEI-Int-RHC-01.12 67

Uponor Radiant Heating/Cooling > Uponor controls Uponor control stations Uponor room control station RS 2 Pumpgroup for control of UFH in single rooms, with brass-housing, bracket for front-or backside installation, integrated pump grundfos UP15-14B, venting screw, secondary max.- limiter 25-55 C, balancing valve, actuator 230V, 1-3 kw max. 90 primary, max. 55 secondary, max. 10 bar valve kvs 1,25 m³/h Pump 15-40 for 0,1-0,45 ³/h 1,2-03, m, 230V, 30W, connection: secondary loop 3/4"" eurocone primary valves with clampconnection for CU-Pipe 15mm Pump needs 230V pump power supply with external switch. connectible to electrical thermostats no. 1000132 calculation example for Rl,B 0,05m²K/W (tiles) pipe 9,9x1,1 100mm 2 loops a' 60m, =2x 6m² 0,96kW pipe 14x2 150mm 2loops a' 60m = 2x 9m² 1,8 kw pipe 17x2 150mm 2loops a' 90m = 2x14m² 2,8 kw pipe 20x2,0 150mm 2loops a' 105m = 2x16m² 3,2 kw Item no. Q [kw] l [mm] w [mm] h [mm] c/c [mm] c/c1 [mm] Description unit 1005576 2 360 145 80 60 40 Uponor Room control unit RS 2 up to 2 kw with actuator 230V FT G 3/4 l Uponor branch connection For extension of RS 2 room control station to 2 heating circuits; direct connection of heating circuit G 3/4 fitting with Euro cone Each kit includes 2 fittings. Material: Brass G 3/4 G 3/4 r a Item no. l [mm] c/c [mm] Description unit 1005675 50 40 Uponor branch connection for connection of two loops to Uponor RS 2 1 set Uponor Push 23 Pumpgroup with thermostat and pump energy efficiency class A, Thermostat with capillary sensor 20-55 C for supply temp., Pump Grundfos Alpha2L 15-60 0,1-2,4 m³/h, H: 4-0,9 m supply thermostat valve kvs 0,9 m³/h return balancing valve kvs 2,0 m³/h secondary connections G1A for connection to uponor UFHC manifolds, 10 kw max. 90 primary, max. 55 secondary, max. 10 bar 1046870 Uponor push 23 A, pump and mixing group for constant temperature control 68 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor controls Uponor control stations Uponor Manifold Pump Group MPG 10 Pumpgroup for connection to Uponor UFHC-manifolds, installation with manifolds on-wall or in cabinets, pre-mounted with supply temperature control C-46 with integrated interface to uponor single room control C-56 3-way-mixing valve, motor drive kvs 4,0 pump energy efficiency class A (Grundfos alpha2l 25-60) 0,1-2,5 m³/h H: 6,0-1 m proportional pressure control primary ballvalves, connection Rp1 (FT) secondary connection G1A (MT) supplytemperature sensor outdoor temperature sensor (install. on buildingsite) 3-10 kw max. 90 primary, max. 60 secondary, max. 10 bar 1048780 Uponor Manifold Pump Group MPG 10 with controller Uponor Manifold Pump Group MPG 10 without controller to connect to uponor UFHC-manifolds, installation with manifolds on-wall or in cabinets, without actuator, without control, for connection to external boiler control or connection to Uponor climate controller C-46 heating/cooling, requires Motor 1002356 or 1002357 3-way-valve mixing kvs 4,3 pump energy efficiency class A (Grundfos alpha2l 15-60) Q: 0,1-2,5 m³/h, H: 6-2,4 m proportional pressure control connection G1A secondary ball valve+balancing valve primary for installation left or right of manifold 3-10 kw max. 90 primary, max. 60 secondary 1048781 Uponor Manifold Pumpgroup MPG 10 without controller EEI-Int-RHC-01.12 69

Uponor Radiant Heating/Cooling > Uponor controls Uponor control stations Uponor Central Pump group CPG 15 Pumpgroup for installation in boiler rooms or on-wall with Uponor UFHCmanifolds, pre-mounted with supply temperature control C-46 with integrated interface to Uponor single room control C-56 3-way-mixing valve, motor drive kvs 6,3 pump energy efficiency class A (Grundfos alpha2l 25-60) 0,1-2,5 m³/h H: 6,0-1 m proportional pressure control primary ball valves, connection Rp1 (FT) secondary connection G1A (MT) supply temperature sensor outdoor temperature sensor (install. on buildingsite) 3-15 kw max. 90 primary, max. 60 secondary, max. 10 bar 1048782 Uponor Central Pump group CPG 15 with controller Uponor Central Pump group CPG 15 without controller installation in boiler rooms, without actuator, without control, for connection to external boiler control or connection to Uponor climate controller C-46 heating/cooling, requires Motor 1002356 or 1002357 3-way-mixing valve, for motor drive 1002356 or 1002357 kvs 6,3 pump energy efficiency class A (Grundfos alpha2l 15-60) Q: 0,1-2,5 m³/h, H: 6-2,4 m proportional pressure control primary connection Rp1 (FT) secondary ballvalves, connection Rp1 (FT) 3-15 kw max. 90 primary, max. 60 secondary, max. 10 bar 1048783 Uponor Central Pumpgroup CPG 15 without controller 70 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor industrial underfloor heating Uponor Industrial Under oor Heating Uponor industrial underfloor heating is a low-temperature heat distribution system for heating industrial spaces. The system is built directly into the concrete floor slab. It is even possible to make use of the standard steel reinforcement for the concrete slab as a support structure for the heating pipes. Heat can be supplied by any conventional warm water heating system designed for use in the type of building being in question. Your advantages Rapid return on investment Total design space freedom Optimal building space utilisation Uniform temperature profile Low air speeds No dust circulation Stimulating working environment No maintenance costs Proven technology Extensive declaration of liability System components Uponor industrial clamp track Systempipe / -Fittings Additional components Manifold / Cabinets Uponor PE-Xa pipe 25x2.3 or 20x2.0 Uponor pipe bend suport Uponor industrial manifold 25-G 11/2 Uponor cable tie Uponor Q&E PPSU coupling Uponor conduit D Uponor pipe clips Uponor Q&E brass connection with male thread /2 150 Uponor tying wire EEI-Int-RHC-01.12 71

Uponor Radiant Heating/Cooling > Uponor industrial underfloor heating Uponor industrial oor heating PE-Xa pipes Uponor PE-Xa pipes PE-Xa pipe with an oxygen diffusion barrier manufactured from peroxide cross-linked polyethylene (PE-Xa) using the Engel method complying with e.g. preniso 15875 Plastics piping systems for hot and cold water installations - Cross-linked polyethylene with an oxygen diffusion barrier of EVOH (ethyl vinyl alcohol). Uponor pipes fulfil the requirements for oxygen diffusion resistance as per DIN 4726. Malfunction temperature 95 C. Design pressure 8,8 bar (at 70 C). Item no. d [mm] s [mm] l [m] V [l/m] Description unit 1009230 20 2.0 240 0.2 Uponor pe PE-Xa Q&E pipe 20x2.0 240 m coil 240 m 1009231 20 2.0 480 0.2 Uponor pe PE-Xa Q&E pipe 20x2.0 480 m coil 480 m Uponor eval PE-Xa Q&E pipe in coils Pipes manufactured from peroxide cross-linked polyethylene (PE-Xa) using the Engel method, complying with e.g. EN ISO 15875 Plastics piping systems for hot and cold water installations - Cross-linked polyethylene. Includes an ethylene vinyl alcohol (EVOH) oxygen barrier layer, complying with DIN 4726, to prevent corrosion of system components. This barrier has been specially developed to work together with Uponor Q&E fitting technology. Classification of service conditions (including typical field of application): Application class 4 - Underfloor heating and low temperature radiators, malfunction temperature 95 C. Design pressure 6 bar. Application class 5 - high temperature radiators, malfunction temperature 95 C. Design pressure 6 bar. Item no. d [mm] s [mm] l [m] p [bar] Description unit 1023448 25 2.3 205 6 Uponor eval PE-Xa Q&E pipe 25x2.3 coil lengths 205 m 205 m 1047615 25 2.3 303 6 Uponor eval PE-Xa Q&E pipe 25x2.3 coil lengths 303 m 303 m 1047618 25 2.3 640 6 Uponor eval PE-Xa Q&E pipe 25x2.3 coil lengths 640 m 640 m Uponor PE-Xa Q&E ttings Uponor Q&E PPSU coupling equal Made of PPSU. Note: Uponor Q&E Ring must be ordered separately! Item no. d [mm] p [bar] Description unit 1008932 20 6+10 Uponor Q&E PPSU coupling 20-20 5 pcs 1008671 25 6+10 Uponor Q&E PPSU coupling 25-25 5 pcs IG z l d AG z l d Uponor compression adapter Compression adapter made of brass, for connection of Uponor PE-X pipes with 3/4" female thread. SW 1 SW SW 1 SW Item no. d [mm] MT ["] FT ["] l [mm] A/F [mm] z [mm] Description unit 1005295 25 R 3/4 50 37/27 15 Uponor compression adapter 25x2.3-3/4"MT 10 pcs 1005296 25 Rp 1 40 37/38 8 Uponor compression adapter 25x2.3-1" FT 10 pcs 1005297 25 Rp 3/4 35 37/31 8 Uponor compression adapter 25x2.3-3/4 FT 10 pcs 1005298 25 R 1 53 37/34 20 Uponor compression adapter 25x2.3-1" MT 10 pcs 72 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor industrial underfloor heating Uponor PE-Xa Q&E ttings Uponor Q&E brass connection with male thread Made of DR brass. Male thread acc.to DIN EN 10226-1 for sealing in. Note: Uponor Q&E Ring must be ordered separately! Item no. d [mm] MT ["] p [bar] Description unit 1023006 20 R 3/4 6+10 Uponor Q&E connection with male thread taper, 20-3/4 5 pcs 1023007 25 R 3/4 6+10 Uponor Q&E connection with male thread taper, 25-3/4 5 pcs 1023008 25 R1 6+10 Uponor Q&E connection with male thread taper, 25-1 5 pcs Uponor Q&E brass connection with female thread Made of DR brass. Female thread acc. to DIN EN 10226-1. Note: Uponor Q&E Ring must be ordered separately! Item no. d [mm] FT ["] p [bar] Description unit 1023011 20 Rp 3/4 6+10 Uponor Q&E connection with female thread 20-3/4 5 pcs 1023012 25 Rp 3/4 6+10 Uponor Q&E connection with female thread 25-3/4 5 pcs 1023013 25 Rp 1 6+10 Uponor Q&E connection with female thread 25-1 5 pcs Uponor Q&E ring natural Made of PE-X. Uponor Q&E rings natural intended for Uponor Q&E fittings. For PE-Xa pipe dimensions 16, 20, 25, 32, 40, 50 and 63 mm. Item no. d [mm] colour [-] p [bar] Description unit 1042836 20 natural 6+10 Uponor Q&E ring natural with stop edge Uponor PE-Xa dim 20 mm 20 pcs 1042840 25 natural 6+10 Uponor Q&E ring natural with stop edge for Uponor PE-Xa dim 25 mm 20 pcs Uponor industrial oor heating xation and accessories Uponor industrial clamp track Uponor clamp track for fixation of Uponor PEX pipes. d r a h l b Item no. w [mm] h [mm] d [mm] c/c [mm] l [mm] Description unit 1005290 50 34 25 50 3000 Uponor clamp track for 25 mm pipes 30 m 1005358 40 26 20 50 3000 Uponor clamp track for 20 mm pipes 30 m Uponor fastening nail For fastening the Uponor clamp track 25 Item no. w [mm] h [mm] Description unit 1005291 36 50 Uponor fastening nail for industrial floor heating clamp track 500 pcs EEI-Int-RHC-01.12 73

Uponor Radiant Heating/Cooling > Uponor industrial underfloor heating Uponor industrial oor heating xation and accessories Uponor pipe clips For fastening Uponor pipes on reinforcement steel meshes. Item no. h [mm] h1 [mm] w [mm] d [mm] d1 [mm] Description unit 1005289 57 27 38 25 3-8 Uponor pipe clips for PE-Xa pipe 25x2.3 250 pcs Uponor cable tie For fastening Uponor pipes on reinforcement steel meshed. Made of polyamide. Item no. w [mm] l [mm] Description unit 1005287 5 200 Uponor cable ties, length 200 mm for the pipe assembly on support mats 100 pcs 1005372 7 280 Uponor cable ties, length 280 mm for the pipe assembly on support mats 100 pcs Uponor tying wire For fastening Uponor pipes on reinforcement steel meshes. Made of steel. 250 pcs per bag. 1009222 Uponor tying wire, 150 x 1.25 250 pcs Uponor pipe bend support Made of galvanized steel as bend support for the pipes in the manifold area. Item no. d [mm] Description unit 1009233 20 Uponor pipe bend support 20 mm 50 pcs 1009006 25 Uponor pipe bend support 22-25 mm 20 pcs Uponor conduit Corrugated, fire classification E conforming to DIN EN 13501-1. Supplied in coils. Item no. d [mm] d1 [mm] d2 [mm] colour [-] Description unit Uponor conduit black 35/29 MLC 25 1012869 35/29 25 black 50 m 74 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor industrial underfloor heating Uponor industrial oor heating manifold and accessories Uponor industrial manifold 25-G 11/2 Uponor Industrial Manifold 25-G 11/2 as supply / return for Industrialheating, made of: - supply-segment, with control valves for preadjustment, heating loop connection for PE-Xa Pipe 25x2,3 with compression adapter. - return-segment with thermostat upper section incl. cap for locking, Uponor actuator can be mounted directly on the return manifold, heating loop connection for PE-Xa Pipe 25x2,3 with compression adapter Spacing of outlet: 100 mm Material: fibreglass reinforced Polyamid max. operating temperatur: 60 C max. operating pressure 6 bar induvidual combination up to 20 loops max. Number of needed brackets loops 2-5 6-9 10-14 15-19 20 bracket 2 3 4 5 6 1045813 Uponor industrial manifold 25-G 1 1/2" 1 set Uponor industrial manifold G3/4 Eurcone as supply / return for Industrialheating, made of: - supply-segment, with control valves for preadjustment, heating loop connection for G3/4 eurocone. - return-segment with thermostat upper section incl. cap for locking, Uponor actuator can be mouinted directly on the return manifold, heating loop connection for G3/4 eurocone. Spacing of outlet: 100 mm Material: fibreglass reinforced Polyamid max. operating temperatur: 60 C max. operating pressure: 6 bar induvidual combination up to 20 loops max. Quantity necesary bracket loops 2-5 6-9 10-14 15-19 20 bracket 2 3 4 5 6 1045814 Uponor industrial manifold G3/4 eurocone 1 set Uponor industrial manifold basic kit Uponor Industrial Manifold Basic Kit for mounting the industrial manifold, made of: - 2 St. brackets short - 2 St. brackets long - 2 St. filling valve brass - 2 St. thermometer 0-60 C - 1 St. manometer - 2 St. endcap - 2 St. flat sealing screw connection piece with swivel nut - 1 St. mounting material: 8x screws 6x60mm 8x plastic anchor 8x40mm 2x flat sealing 44x32x2 1045815 Uponor industrial manifold basic kit 1 set EEI-Int-RHC-01.12 75

Uponor Radiant Heating/Cooling > Uponor industrial underfloor heating Uponor industrial oor heating manifold and accessories Uponor industrial manifold bracket kit Uponor Industrial Manifold Bracket Kit for mounting the Industrial manifold, made of: - 2 St. brackets short - 2 St. brackets long - 1 St. mounting material: 8x screws 6x60mm 8x plastic anchor 8x40mm 1045816 Uponor industrial manifold bracket kit 1 set Uponor industrial flowmeter Uponor Industrial Flowmeter For adjusting the water quantity of the individual heating loops in a range of 4-20 l/min. Water quantity is indicated in the inspection window. With shut-off function. Made of fibre-glass reinforced polyamid. Material: fibreglass reinforced Polyamid 1030134 Uponor industial flowmeter Uponor industrial ball valve G 11/2 Uponor Industrial Ball Valve G 11/2 for use with the Uponor Industrial manifold G 11/2 connection: - G 11/2 FT - G 11/2 MT Material: brass 1030135 Uponor industrial ball valve G 1 1/2" 1 set 76 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor snow and ice melting Uponor snow and ice melting Uponor snow and ice melting system is best suitable for all outside surfaces which are provided with a solid covering. It will be especially used for driveways, ramps, fire department or hospital approach roads, helicopter landing zones, sidewalks, football pitches, etc.. Your advantages System ensures a maximum of security - round the clock Automatically deicing, no more shoveling of snow Avoids environmental stress and damage through de-icing salt Usage of industrial waste heat possible Fast and easy installation with robust Uponor PE-X pipes Complete system with all components available Reduces slip and fall liability System components Systempipe / -Fittings Additional components Manifold / Cabinets Uponor cable tie Uponor snow and ice melting pipe 25x2.3 Uponor pipe bend suport Uponor Manifolds D Uponor industrial clamp track Uponor compression adapter PE-X Uponor conduit Uponor Supply pipes Uponor fastening nail Uponor supply accessories Uponor tying wire Uponor electrofusion fitting EEI-Int-RHC-01.12 77

Uponor Radiant Heating/Cooling > Uponor snow and ice melting Uponor snow and ice melting pipes Uponor snow and ice melting pipe Uponor snow and ice melting pipes manufactured from cross-linked polyethylene, complying with e.g. EN ISO 15875 Plastics piping systems for hot and cold water installations - Cross-linked polyethylene. Application for underfloor heating up to 50 C water temperature Design pressure 4 bar. 1022341 Uponor Meltaway PE-X pipe 25x2.3 920 m 920 m 1033625 Uponor Meltaway PE-X pipe 25x2.3 1020 m 1020 m 1033626 Uponor Meltaway PE-X pipe 25x2.3 other lengths <1000m 1 m Uponor snow and ice melting manifold and accessories Uponor manifolds Uponor snow and ice melting single manifold made of high density polyethylene (HDPE) pipe and equipped with compact-welded couplings. Couplings between centres are 500mm. 1033637 Uponor Meltaway manifold 10 way single outlet, C/C 600 75 6m 1033638 Uponor Meltaway manifold 10 way single outlet, C/C 600 110 6m 1033639 Uponor Meltaway manifold 10 way single outlet, C/C 600 160 6m 1033640 Uponor Meltaway manifold 40 way single outlet, C/C 150 75 6m 1033641 Uponor Meltaway manifold 30 way single outlet, C/C 200 75 6m 1033642 Uponor Meltaway manifold 30 way single outlet, C/C 200 110 6m 1033643 Uponor Meltaway manifold 30 way single outlet, C/C 200 160 6m 1033645 Uponor Meltaway manifold 40 way single outlet, C/C 150 110 6m 1033647 Uponor Meltaway manifold 40 way single outlet, C/C 150 160 6m Uponor manifolds Uponor snow and ice melting single manifold made of high density polyethylene (HDPE) pipe and equipped with compact-welded couplings. Couplings between centres are 500mm. 1033631 Uponor Meltaway manifold 12 way single outlet, C/C 500 75 6m 1033632 Uponor Meltaway manifold 12 way single outlet, C/C 500 110 6m 1033633 Uponor Meltaway manifold 12 way single outlet, C/C 500 160 6m 78 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor snow and ice melting Uponor snow and ice melting manifold and accessories Uponor manifolds Uponor snow and ice melting double manifold made of high density polyethylene (HDPE) pipe and equipped with compact-welded couplings oriented in two directions with an angle of 120 between them. 1033634 Uponor Meltaway manifold 12 way double outlet, C/C 500 75 6m 1033635 Uponor Meltaway manifold 12 way double outlet, C/C 500 110 6m 1033636 Uponor Meltaway manifold 12 way double outlet, C/C 500 160 6m 1033646 Uponor Meltaway manifold 40 way double outlet, C/C 150 110 6m 1033644 Uponor Meltaway manifold 40 way double outlet, C/C 150 75 6m Uponor coupling Uponor straight couplings for snow and ice melting PE-X pipes 25x2.3 Made of HDPE. 1033672 Uponor Meltaway coupling 25x2.3 mm short, 145 mm 1033678 Uponor Meltaway coupling 25x2.3 mm long, 290 mm Uponor supply pipes Uponor snow and ice melting supply pipes made of HDPE. 1033628 Uponor HDPE supply pipe 75x6.8 mm L=6000 mm 1 m 1033629 Uponor HDPE supply pipe 110x6.6 mm L=6000 mm 1 m 1033630 Uponor HDPE supply pipe 160x9.5 mm L=6000 mm 1 m Uponor supply pipes tees Uponor snow and ice melting tees made of HDPE. 1033648 Uponor tee 75 1033649 Uponor tee 110 1033650 Uponor tee 160 EEI-Int-RHC-01.12 79

Uponor Radiant Heating/Cooling > Uponor snow and ice melting Uponor snow and ice melting manifold and accessories Uponor supply pipes elbows Uponor snow and ice melting elbows made of HDPE. 1033652 Uponor elbow 75 x 90 1033653 Uponor elbow 110 x 90 1033654 Uponor elbow 160 x 90 Uponor supply pipes reducer Uponor snow and ice melting reducer made of HDPE. 1056656 Uponor reducer 110-75 1033657 Uponor reducer 160-110 Uponor supply pipes end cap Uponor snow and ice melting end cap made of HDPE. 1033659 Uponor end cap 75 1033660 Uponor end cap 110 1033661 Uponor end cap 160 Uponor flange support Uponor snow and ice melting flange support for connection of Uponor flange to supply/return pipes. Made of HDPE. 1033662 Uponor flange support 75 1033663 Uponor flange support 110 1052123 Uponor flange support 160 80 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor snow and ice melting Uponor snow and ice melting manifold and accessories Uponor flange Uponor snow and ice melting flange made of HDPE. 1033666 Uponor flange 75x6.8 mm 1033667 Uponor flange 110x6.6 mm 1033668 Uponor flange 160x9.5 mm Uponor electrofusion fitting Uponor snow and ice melting electrofusion fittings made of HDPE. 1033673 Uponor electrofusion fitting for pipe 75x6.8 mm 1033675 Uponor electrofusion fitting for pipe 110x6.6 mm 1033676 Uponor electrofusion fitting for pipe 160x9.5 mm Uponor industrial clamp track Uponor clamp track for fixation of Uponor PEX pipes. d r a h l b Item no. w [mm] h [mm] d [mm] c/c [mm] l [mm] Description unit 1005290 50 34 25 50 3000 Uponor clamp track for 25 mm pipes 30 m Uponor fastening nail For fastening the Uponor clamp track 25 Item no. w [mm] h [mm] Description unit 1005291 36 50 Uponor fastening nail for industrial floor heating clamp track 500 pcs Uponor cable tie For fastening Uponor pipes on reinforcement steel meshed. Made of polyamide. Item no. w [mm] l [mm] Description unit 1005287 5 200 Uponor cable ties, length 200 mm for the pipe assembly on support mats 100 pcs 1005372 7 280 Uponor cable ties, length 280 mm for the pipe assembly on support mats 100 pcs EEI-Int-RHC-01.12 81

Uponor Radiant Heating/Cooling > Uponor snow and ice melting Uponor snow and ice melting manifold and accessories Uponor tying wire For fastening Uponor pipes on reinforcement steel meshes. Made of steel. 250 pcs per bag. 1009222 Uponor tying wire, 150 x 1.25 250 pcs Uponor pipe bend support Made of galvanized steel as bend support for the pipes in the manifold area. Item no. d [mm] Description unit 1009006 25 Uponor pipe bend support 22-25 mm 20 pcs Uponor conduit Corrugated, fire classification E conforming to DIN EN 13501-1. Supplied in coils. Item no. d [mm] d1 [mm] d2 [mm] colour [-] Description unit Uponor conduit black 35/29 MLC 25 1012869 35/29 25 black 50 m IG z l d AG z l d Uponor compression adapter Compression adapter made of brass, for connection of Uponor PE-X pipes with 3/4" female thread. SW 1 SW SW 1 SW Item no. d [mm] MT ["] FT ["] l [mm] A/F [mm] z [mm] Description unit 1005297 25 Rp 3/4 35 37/31 8 Uponor compression adapter 25x2.3-3/4 FT 10 pcs 1005296 25 Rp 1 40 37/38 8 Uponor compression adapter 25x2.3-1" FT 10 pcs 1005295 25 R 3/4 50 37/27 15 Uponor compression adapter 25x2.3-3/4"MT 10 pcs 1005298 25 R 1 53 37/34 20 Uponor compression adapter 25x2.3-1" MT 10 pcs Uponor chamfering tool For de-studding the Uponor snow and ice melting pipe. 1033689 Uponor Meltaway chamfering tool for Uponor Meltaway 25 mm pipe 82 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor sport floor heating Uponor sports oor heating Uponor radiant heating system for surface elastic floors. These floors are a synthesis of wooden swing floors with elastic layer made of PVC or linoleum. The heating registers runs in pipe holders (Patent Uponor) directly under the blind floor. The pipes are to be connected to distribute- /collector pipes. Uponor sports floor heating systems are quick installed. First due to the flexible and at the same time robust PE-Xa pipe material. Secondly due to the patented mounting principle for swing floor constructions. Your advantages Sports floor heating systems offer high thermal comfort Provides mild radiant heat and an even temperature distribution with low air speed Gives athletes and architectures all freedom, because the system is invisible Takes all hygienic and physiologic requirements of sports halls into consideration Energy saving due to operation with low heating water temperatures sprung floors System components Uponor pipe fixation Systempipe / -Fittings Uponor eval PE-Xa pipe in coils Additional components Manifold / Cabinets Uponor Q&E tichelmann manifold for sportsfloor UFH Uponor pipe bend suport Uponor pipe fixation double Uponor conduit EEI-Int-RHC-01.12 83

Uponor Radiant Heating/Cooling > Uponor sport floor heating Uponor sport oor PE-Xa pipes Uponor eval PE-Xa Q&E pipe in coils Pipes manufactured from peroxide cross-linked polyethylene (PE-Xa) using the Engel method, complying with e.g. EN ISO 15875 Plastics piping systems for hot and cold water installations - Cross-linked polyethylene. Includes an ethylene vinyl alcohol (EVOH) oxygen barrier layer, complying with DIN 4726, to prevent corrosion of system components. This barrier has been specially developed to work together with Uponor Q&E fitting technology. Classification of service conditions (including typical field of application): Application class 4 - Underfloor heating and low temperature radiators, malfunction temperature 95 C. Design pressure 6 bar. Application class 5 - high temperature radiators, malfunction temperature 95 C. Design pressure 6 bar. Item no. d [mm] s [mm] l [m] p [bar] Description unit 1023448 25 2.3 205 6 Uponor eval PE-Xa Q&E pipe 25x2.3 coil lengths 205 m 205 m 1047615 25 2.3 303 6 Uponor eval PE-Xa Q&E pipe 25x2.3 coil lengths 303 m 303 m 1047618 25 2.3 640 6 Uponor eval PE-Xa Q&E pipe 25x2.3 coil lengths 640 m 640 m Uponor sport oor PE-Xa Q&E ttings Uponor Q&E PPSU coupling equal Made of PPSU. Note: Uponor Q&E Ring must be ordered separately! Item no. d [mm] p [bar] Description unit 1008671 25 6+10 Uponor Q&E PPSU coupling 25-25 5 pcs Uponor Q&E brass connection with male thread Made of DR brass. Male thread acc.to DIN EN 10226-1 for sealing in. Note: Uponor Q&E Ring must be ordered separately! Item no. d [mm] MT ["] p [bar] Description unit 1023007 25 R 3/4 6+10 Uponor Q&E connection with male thread taper, 25-3/4 5 pcs 1023008 25 R1 6+10 Uponor Q&E connection with male thread taper, 25-1 5 pcs Uponor Q&E brass connection with female thread Made of DR brass. Female thread acc. to DIN EN 10226-1. Note: Uponor Q&E Ring must be ordered separately! Item no. d [mm] FT ["] p [bar] Description unit 1023012 25 Rp 3/4 6+10 Uponor Q&E connection with female thread 25-3/4 5 pcs 1023013 25 Rp 1 6+10 Uponor Q&E connection with female thread 25-1 5 pcs Uponor Q&E ring natural Made of PE-X. Uponor Q&E rings natural intended for Uponor Q&E fittings. For PE-Xa pipe dimensions 16, 20, 25, 32, 40, 50 and 63 mm. Item no. d [mm] colour [-] p [bar] Description unit 1042840 25 natural 6+10 Uponor Q&E ring natural with stop edge for Uponor PE-Xa dim 25 mm 20 pcs 84 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor sport floor heating Uponor sport oor xation and accessories Uponor pipe fixation For exact leading of pipes inside the channels of sport floor Material: Polyamid Item no. l [mm] sd [mm] c/c [mm] l1 [mm] h [mm] Description unit 1005286 290 45 100 145 50 Uponor pipe clip track for floors in gyms. Polyamid 25 pcs Uponor pipe fixation double For exact leading of pipes in the bending zone of chanels of sport floor Material: galvanised steel Item no. l1 [mm] c/c [mm] l [mm] Description unit 1005284 105 100 975 Uponor double pipe clip track for floors in gyms. galvanised steel Q&E tichelmann manifold 2 circuits for sportsfloor UFH as manifold for the use in sportsfl oor UFH systems according to thetichelmann principle. For connection of Uponor PE-Xa pipes 25x2.3mmwith Uponor Q&E connection technology consisting of:- 1 manifold (distributor & collector)- 4 Q&E rings 25-2 Q&E rings 40Material: Uponor eval PE-Xa pipes + Uponor PPSU fittings. Item no. d [mm] l [mm] c/c [mm] Description unit 1046747 40 2084 150 Uponor Q&E tichelmann manifold 2 circuits for sportsfloor UFH 1 set Q&E tichelmann manifold for sportsfloor UFH as manifold for the use in sportsfloor UFH systems according to the Tichelmann principle. For connection of Uponor PE-Xa pipes 25x2.3mm with Uponor Q&E connection technology consisting of: - 1 manifold (distributor & collector) - 6 Q&E rings 25-2 Q&E rings 40 Material: Uponor eval PE-Xa pipes + Uponor PPSU fittings Item no. d [mm] l [mm] c/c [mm] Description unit 1046748 40 2084 150 Q&E tichelmann manifold for sportsfloor UFH 1 set Q&E tichelmann manifold end segment for sportsfloor UFH as manifold for the use in sportsfloor UFH systems according to the Tichelmann principle. For connection of Uponor PE-Xa pipes 25x2.3mm with Uponor Q&E connection technology consisting of: - 1 manifold (distributor & collector) - 6 Q&E rings 25 Material: Uponor eval PE-Xa pipes + Uponor PPSU fittings Item no. d [mm] l [mm] c/c [mm] Description unit 1046749 40 2036 150 Q&E tichelmann manifold end segment for sportsfloor UFH 1 set EEI-Int-RHC-01.12 85

Uponor Radiant Heating/Cooling > Uponor sport floor heating Uponor sport oor xation and accessories Uponor eval PE-Xa pipes in straight lengths Pipes manufactured from peroxide cross-linked polyethylene (PE-Xa) using the Engel method, complying with e.g. EN ISO 15875 Plastics piping systems for hot and cold water installations - Cross-linked polyethylene. Includes an ethylene vinyl alcohol (EVOH) oxygen barrier layer, complying with DIN 4726, to prevent corrosion of system components. This barrier has been specially developed to work together with Q&E fitting technology. Classification of service conditions (including typical field of application): Application class 4 - Underfloor heating and low temperature radiators, malfunction temperature 95 C. Design pressure 6 bar. Application class 5 - High temperature radiators, malfunction temperature 95 C. Design pressure 6 bar. Item no. d [mm] s [mm] l [m] p [bar] Description unit 1008939 40 3.7 6 6 Uponor eval PE-Xa Q&E pipe 40x3.7 mm in straight lengths of 6 m 6 m Uponor Q&E PPSU coupling equal Made of PPSU. Note: Uponor Q&E Ring must be ordered separately! Item no. d [mm] p [bar] Description unit 1008673 40 6 Uponor Q&E PPSU coupling 40-40 Uponor Q&E PPSU elbow 90 Made of PPSU. Note: Uponor Q&E Ring must be ordered separately! Item no. d [mm] p [bar] Description unit 1008683 40 6 Uponor Q&E PPSU elbow 90 40-40 Uponor Q&E ring natural Made of PE-X. Uponor Q&E rings natural intended for Uponor Q&E fittings. For PE-Xa pipe dimensions 16, 20, 25, 32, 40, 50 and 63 mm. Item no. d [mm] colour [-] p [bar] Description unit 1045464 40 natural 6 Uponor Q&E ring natural with stop edge for Uponor PE-Xa dim 40 mm 5 pcs Uponor Q&E brass connection with female thread Made of DR brass. Female thread acc. to DIN EN 10226-1. Note: Uponor Q&E Ring must be ordered separately! Item no. d [mm] FT ["] p [bar] Description unit Uponor Q&E connection with female thread 1047867 40 Rp 1 1/4 6 40-1 1/4 86 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor sport floor heating Uponor sport oor xation and accessories Uponor pipe bend support Made of galvanized steel as bend support for the pipes in the manifold area. Item no. d [mm] Description unit 1009006 25 Uponor pipe bend support 22-25 mm 20 pcs Uponor conduit Corrugated, fire classification E conforming to DIN EN 13501-1. Supplied in coils. Item no. d [mm] d1 [mm] d2 [mm] colour [-] Description unit Uponor conduit black 35/29 MLC 25 1012869 35/29 25 black 50 m EEI-Int-RHC-01.12 87

Uponor Radiant Heating/Cooling > Uponor comfort panel Uponor Comfort Panel The Uponor comfort panel is a suspended ceiling system which can be used for heating and cooling. The system consist of thermally activated ceiling panels which can be installed fast and easy into conventional suspended ceiling grids. Your advantages cooling power up to 92.5 W/m² with 10K under temperature Heating power up to 82.5 W/m² with 15 K under temperature Compatible with existing metal rail constructions easy to install quick installation concealed installation/integrated in the ceiling structure easily retrofitted into existing ceiling structure excellent for both new buildings and refurbishment easy to operate maintenance-free. System components Systempipe / -Fittings Additional components Manifold / Cabinets Uponor Comfort Panel Uponor PE-X Pipe 10x1.5 Uponor Dynamic volume flow controller Uponor Slip Connector Uponor blind panel Uponor connection MLC Uponor connection with female threat 88 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor comfort panel Uponor comfort panel Uponor comfort panel For cooling and heating of buildings with suspended raster frame ceiling. For already existing or new raster frames under the ceiling. With optically sophisticated surface from fleece coated steel sheet. High performance due to optimised thermal conductivity between surface and integrated pipes, made of PE-X, with thermal insulation made of mineral fibres. Cooling capacity 74 W/m² by 8 K temperature difference complies with EN 14240 Heating capacity 103 W/m² by 15 K temperature difference complies with EN 14037 l h b Item no. l [mm] w [mm] h [mm] Description unit 1045315 1240 615 23 Uponor comfort panel 1250 x 625 1045316 1190 590 23 Uponor comfort panel 1200 x 600 Uponor comfort panel b l h For cooling and heating of buildings with suspended raster frame ceiling. For already existing or new raster frames under the ceiling. With optically sophisticated surface from fleece coated steel sheet. High performance due to optimised thermal conductivity between surface and integrated pipes, made of PE-X, with thermal insulation made of mineral fibres. Cooling capacity 74 W/m² by 8 K temperature difference complies with EN 14240 Heating capacity 103 W/m² by 15 K temperature difference complies with EN 14037 Item no. l [mm] w [mm] h [mm] Description unit 1045317 615 615 23 Uponor comfort panel 625 x 625 1045318 590 590 23 Uponor comfort panel 600 x 600 EEI-Int-RHC-01.12 89

Uponor Radiant Heating/Cooling > Uponor comfort panel Uponor comfort panel - accessories l h Uponor blind panel For use in on-site installed suspended raster ceilings. With optically sophisticated surface from fleece coated mineral faser board, optically fits exactly to comfort panel. Colour from below: white Acoustical absorption (alpha w): 1,00 Acoustical absorption (NRC): 0,95 Building material class according to DIN 4102: A1 b Item no. l [mm] w [mm] h [mm] A [m²] Weight [kg] Description unit 1022983 1242 617 18 0.76 2.08 Uponor Blind Panel 625 dimension 617 x 1242 x 18 16 pcs 1022984 1195 595 18 0.71 1.93 Uponor Blind Panel 600 dimension 595 x 1195 x 18 16 pcs l h Uponor blind panel For use in on-site installed suspended raster ceilings. With optically sophisticated surface from fleece coated mineral faser board, optically fits exactly to comfort panel. Colour from below: white Acoustical absorption (alpha w): 1,00 Acoustical absorption (NRC): 0,95 Building material class according to DIN 4102: A1 b Item no. l [mm] w [mm] h [mm] Description unit 1045319 615 615 18 Uponor Blind Panel 625 x 625 32 pcs 1045320 590 590 20 Uponor Blind Panel 600 x 600 32 pcs b Uponor blind frame For use in existing suspended ceiling constructions for optical devision into a quadratic raster. l Item no. l [mm] w [mm] colour [-] Description unit 1045323 625 24 white Uponor blind frame 625, white 1045324 600 24 white Uponor blind frame 600, white 90 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor comfort panel Uponor comfort panel - accessories Uponor PE-X pipe 10 x 1,5 mm As pipe in coils for connection or extension between 2 comfort panels. Material: Uponor PEX pipe from high pressure cross-linked polyethylene Medium: heating/cooling water acc. to VDI 2035 or water-glycol up to 50% Temperature range: 0 to 60 C Pressure range: 0 to 6 bar by max. 65 C 0 to 12 bar by max. 20 C Surrounding humidity: up to 90% Material: plastic Item no. d [mm] s [mm] l [m] Description unit 1045327 10 1.5 100 Uponor PE-X pipe 10 x 1,5 mm, in coils barrier, 10x1,5 coil 100m, 6bar 100 m b d Uponor pipe insert, for 10x1,5 PE-X pipe Pipe sleeve made of plastic, for plug in PE-X pipe ends, dimension 10 x 1,5 mm, for stiffening of a pipe in connection area with Uponor slip-connector. Item no. w [mm] d [mm] Description unit 1045328 5 7 Uponor support sleeve, 10 x 1,5 mm 10 pcs d l Uponor slip-connector Push-in fitting for connection of more comfort panels together into one control circuit or to one ceiling panel area. Medium: heating/cooling water acc. to VDI 2035 or water-glycol up to 50% Temperature range: 0 to 60 C Pressure range: 0 to 6 bar by max. 65 C Surrounding humidity: up to 90% Material: plastic Item no. l [mm] d [mm] Description unit 1045325 45 22 Uponor slip-connector equal 10 mm 100 pcs 1022987 60 15 Uponor slip connector equal 15 mm 10 pcs d 1 l d 3 d 2 Uponor slip-connector reduced 15-10 mm Push-in fitting for connection of more comfort panels together into one control circuit or to one ceiling panel area. Medium: heating/cooling water acc. to VDI 2035 or water-glycol up to 50% Temperature range: 0 to 60 C Pressure range: 0 to 6 bar by max. 65 C Surrounding humidity: up to 90% Material: plastic Item no. l [mm] d1 [mm] d2 [mm] d3 [mm] Description unit 1045326 56 32 10 15 Uponor slip-connector reduced 15-10 mm 100 pcs d l Uponor Stop plug 15 as end plug 15 mm, for closing of capillary mats ends Material: nickel-plated brass Item no. d [mm] l [mm] Description unit 1000296 15 35 Uponor stop plug 15 10 pcs EEI-Int-RHC-01.12 91

Uponor Radiant Heating/Cooling > Uponor comfort panel Uponor comfort panel - accessories ø 51,4 63,9 Uponor Diversion Fitting Dim Cu 22 4x Dim 10 push-in (CPII Manifold) Uponor Diversion Fitting Dim Cu 22 4x Dim 10 push-in allows the connection of four series of panels to a MLC 20 mm pipe using an Uponor Press Adapter MLC 20-22CU (item number 1014558). Temperature range: 0 60 C Pressure range: 0-6 bar Material: plastic 1048684 Uponor Diversion Fitting Dim. Cu 22 4x Dim 10 push-in ø 10 35 18 ø 10 ± 0,1 Uponor Endplug Dim 10 push-in Uponor Endplug Dim 10 push-in to close an open distribution line from the Uponor diversion fitting Cu 22 4x 10 mm push-in (1048684) Temperature range: 1 60 C Pressure range: 0-6 bar Material: plastic 1048685 Uponor Endplug Dim 10 push-in l d d 1 Uponor connection MLC For connection of 15 mm push-in system to Uponor MLC pipe. Material: nickel-plated brass, press sleeve Item no. d [mm] d1 [mm] l [mm] Description unit 1000297 15 16x2.0 70 Uponor connection to MLCP 15-16x2 6 pcs 1000298 15 20x2.25 70 Uponor connection to MLCP 15-20x2.25 6 pcs l Uponor connection with male threat d AG for connection of 15 mm push-in system to male threat. Material: nickel-plated brass Item no. d [mm] MT ["] l [mm] Description unit 1000299 15 R 1/2 57 Uponor connection with male threat 15-1/2 MT 6 pcs 1000300 15 R 3/4 57 Uponor connection with male threat 15-3/4 MT 6 pcs l Uponor push-in compression adapter AG d for connection of 15 mm push-in system to female threat. Material: nickel-plated brass Item no. d [mm] MT ["] l [mm] Description unit 1000301 15 R 1/2 41 Uponor push-in compressionadapter 15-1/2 FT 6 pcs l Uponor connection elbow d for connection of 15 mm push-in system to Uponor MLC pipe, in 90 version. Material: nickel-plated brass, press sleeve l 1 d 1 92 Item no. d [mm] d1 [mm] l [mm] l1 [mm] Description unit 1000303 15 16x2 45 48 Uponor connection elbow to Uponor MLC pipes, 15-16x2 6 pcs 1000304 15 20x2.25 45 48 Uponor connection elbow to Uponor MLC pipes, 15-20x2,25 6 pcs EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor comfort panel Uponor comfort panel - accessories Uponor locking ring 15 for capillary pipe 15 mm push-in fitting. Ensures the coupling against unintended (unbeabsichtigtes) solutions of push-in connection. Material: polypropylene Item no. d [mm] Description unit 1000310 15 Uponor locking ring 15 10 pcs Uponor ball valve For closing of cooling and heating areas and supply pipes. Medium: heating/cooling water acc. to VDI 2035 or water-glycol up to 50% Temperature range: -10 to + 110 C Pressure range: 0 to 10 bar Surrounding humidity: up to 95% Material: nickel-plated brass Item no. l [mm] FT ["] Description unit 1022985 50 G 1 Uponor ball valve dimension 1 FT - 1 FT 1022986 50 G 3/4 Uponor ball valve dimension 3/4 FT - 3/4 FT Uponor reduction Reducer from 3/4 MT to 1/2 FT by use of tees for supply and return MLC pipes from dimension 40 x 4 mm Material: brass Item no. FT ["] MT ["] Description unit Uponor reduction 1022988 Rp 1/2 G 3/4 dimension 1/2 FT - 3/4 MT 10 pcs Dynamic volume flow controller For hydraulic control of heating and cooling loops, or zones and indvidual control over integrated valve insert in combination with thermla actuator. Item no. DN [mm] [l/h] stroke [mm] [-] Description unit 1042942 15 90-450 2.25 G 3/4" A Dynamic volume flow controller AB-QM DN 15, flow rate 55-275 L/H 1042943 20 180-900 2.25 G 1" A Dynamic volume flow controller AB-QM DN 20, flow rate 180-900 L/H 1042944 25 340-1700 2.25 G 1 1/4" A Dynamic volume flow controller AB-QM DN 25, flow rate 340-1700L/H 1042945 32 640-3200 2.25 G 1 1/2" A Dynamic volume flow controller AB-QM DN 32, flow rate 640-3200L/H Screw connection for AB-QM Screw connection Inclusively flat sealing Item no. Type [-] FT ["] MT ["] Description unit 1044809 15 Rp 3/4" R 1/2" Screw connection for AB-QM 3/4 MT 1044810 20 Rp 1" R 3/4" Screw connection for AB-QM 1 MT 1044811 25 Rp 1 1/4" R 1" Screw connection for AB-QM 1 1/4 MT 1044812 32 Rp 1 1/2" R 1 1/4" Screw connection for AB-QM 1 1/2 MT EEI-Int-RHC-01.12 93

Uponor Radiant Heating/Cooling > Uponor comfort panel Uponor comfort panel - accessories Thermal actuator TWA -Z NO For control of pressure indipendent volume flow controller - openes when idle. Item no. Type [-] [-] Description unit 1042946 TWA-Z NO Thermal actuator TWA -Z NO Thermal actuator TWA -Z NC For control of pressure indipendent volume flow controller - closes when idle. Item no. Type [-] [-] Description unit 1042947 TWA-Z NC Thermal actuator TWA -Z NC Uponor room temperature controller H/C l l 1 h Concealed device, protects cooling surface from condensation. The TR 2/3 (concealed device) can both to control one valve (heating or cooling) and also be switched over internally to control thus 2 valves (heating and cooling). With an option of external setpoint remove access will it be introduced in two-line (heating and cooling) and three-line systems (heating and cooling). The actual operation status (heating/cooling/ dew point warning) will be show on device by means of light diods. For simplification of wiring and installation of room temperature are switch boxes shall be provided. Operational voltage: 24 V / 50-60 Hz Control range: 5-30 C Switching hysteresis: 1 K Temperature sensor: NTC Switch outlet: Triac, 24 V/1 A, short-term up to 2,5 A Functions: Heating or cooling Heating or cooling with switchover Heating and/or cooling with setpoint remot access Installation site: concealed under plaster, fits into UP-Doses acc. to DIN 49073 Installation depth: 28 mm Colour: RAL 9010, pure white Item no. l [mm] l1 [mm] h [mm] Description unit 1000311 71 70 28 Uponor room thermostat TR 2/3 94 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor comfort panel Uponor comfort panel - accessories Uponor dew point sensor For plastered ceilings or walls / pipe installation, detects a potential condensation arising on the pipe or in the immediate vicinity by changing its electrical resistance. This change of resistance in the sensor is detected by room thermostat TR 2/3, which closes control valve and effectively protects the cooling surface from condense damage. The dew point sensor TF 3 PR is designed for installation in plastered ceilings (P) and for cold-water pipe conduits (R). Installation site: plastered ceilings/walls or pipe installations Item no. l [mm] w [mm] h [mm] Description unit 1000312 70 20 7 Uponor dew point sensor TF 3 PR Uponor dew point sensor For gypsum plasterboard ceilings / suspended metal ceilings, detects a potential condensation arising on the pipe or in the immediate vicinity by changing its electrical resistance. This change of resistance in the sensor is detected by room thermostat TR2/3, which closes control valve and effectively protects the cooling surface from condense damage. The dew point sensor TF 3 GM is designed for installation in gypsum plasterboard ceilings/walls (G) and for suspended metal ceilings (M). Installation site: gypsum plasterboard ceilings/walls or suspended metal ceiling Item no. l [mm] w [mm] h [mm] Description unit 1000313 70 20 7 Uponor dew point sensor TF 3 GM b h Uponor dew point converter l Evaluates the information received from the corresponding dew point sensor. The integrated contact is activated when the dew point is reached. This information can be used, for example, for remote communications with an onsite central building control system or similar device. Up to five dew point sensors can be assigned to each converter. Operating voltage: 24 V / 50-60 Hz Switch outlet: potential free switch over contact max. load capacity of the outlet: 48 V~/60 V DC Installation site: automation cabinet or electric manifold installation Item no. l [mm] w [mm] h [mm] Description unit 1000314 85 36 60 Uponor dew-point converter TK 1 PF EEI-Int-RHC-01.12 95

Uponor Radiant Heating/Cooling > Uponor gypsum panel Uponor Gypsum Panel Uponor Gypsum Panel is the ideal system for heating and cooling. The moderate temperature of the water feeds the radiant system makes it particularly suitable to be combined with condensing boilers, heat pumps, solar panels and other alternative sources of energy. Your advantages quick and easy to install for new buildings and renovation high comfort fast response time completely silent (no fan noise). System components Systempipe / -Fittings Additional components Manifold / Cabinets Uponor Gypsum Panel Uponor PE-Xa pipe 9,9 x 1,1 velta P - a Uponor PE-Xa pipe 20x2 Uponor compression Adapter Uponor Gypsum panel passive Uponor PE-Xa Q&E Coupling Uponor PE-Xa Q&E tee reducer 20x9.9x20 Uponor PE-Xa Pipe 9.9x1.1 expander Uponor PE-Xa Q&E jointing reducer 20x9.9 96 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor gypsum panel Uponor gypsum panel Uponor gypsum panel Radiant panel for heating and cooling applications. Consisting of a gypsum board (15mm), Uponor eval PE-Xa pipe 9.9x1.1 mm and 27mm of EPS 200 (30 kg/m³). Uponor gypsum passive panel has the same layout as the active panels but consists no pipes. Sizes: 2000x1200mm, 1000x1200mm, 500x1200mm. Item no. h [mm] l [mm] w [mm] A [m²] Description unit 1047319 42 2000 1200 2.40 Uponor gypsum panel 2000x1200 Type 2 1047320 42 1000 1200 1.20 Uponor gypsum panel 1000x1200 Type 2 1047321 42 500 1200 0.60 Uponor gypsum panel 500x1200 Type 2 Uponor gypsum panel passive Uponor gypsum panel passive has the same layout as the active gypsum panels (item no. 1047319-21) but contains no pipes. Size: 2000x1200mm Item no. h [mm] l [mm] w [mm] A [m²] Description unit 1020506 42 2000 1200 2.40 Uponor gypsum panel passive 2000x1200 Uponor gypsum panel - accessories Uponor PE-Xa pipes PE-Xa pipe with an oxygen diffusion barrier manufactured from peroxide cross-linked polyethylene (PE-Xa) using the Engel method complying with e.g. preniso 15875 Plastics piping systems for hot and cold water installations - Cross-linked polyethylene with an oxygen diffusion barrier of EVOH (ethyl vinyl alcohol). Uponor pipes fulfil the requirements for oxygen diffusion resistance as per DIN 4726. Malfunction temperature 95 C. Design pressure 8,8 bar (at 70 C). Item no. d [mm] s [mm] l [m] V [l/m] Description unit 1009230 20 2.0 240 0.2 Uponor pe PE-Xa Q&E pipe 20x2.0 240 m coil 240 m 1009231 20 2.0 480 0.2 Uponor pe PE-Xa Q&E pipe 20x2.0 480 m coil 480 m Uponor PE-Xa Q&E coupling 9.9 For Uponor PE-Xa pipe 9.9 x 1.1 mm, consisting of: - 1 coupling - 2 PEX Q&E rings for secure connection Material: Coupling made in brass; PEX Q&E rings made in high-pressure cross-linked polyethylene Item no. d [mm] s [mm] l [mm] z [mm] Description unit 1005264 9.9 1.1 34 4 Uponor PE-Xa Q&E coupling 9.9-9.9 with two PEX rings 10 pcs Uponor PE-Xa conversion nipple For Uponor PE-Xa pipes 9.9 x 1.1 mm, made of brass. Item no. d [mm] MT ["] l [mm] z [mm] A/F [mm] Description unit 1005265 9.9 R 1/2 39 14 22 Uponor PE-Xa conversion nipple 9.9-1/2 with one PEX ring 10 pcs EEI-Int-RHC-01.12 97

Uponor Radiant Heating/Cooling > Uponor gypsum panel Uponor gypsum panel - accessories Uponor PE-Xa Q&E jointing reducer 20x9.9 For connection of Uponor PE-Xa pipes, made of brass. Item no. d [mm] d1 [mm] Description unit 1020518 9.9 20 Uponor PE-Xa Q&E jointing reducer 20 x 9.9 incl. 1 PEX ring 9.9 and 1 PEX ring 20 5 pcs Uponor PE-Xa Q&E tee reducer 20x9.9x20 For connection of Uponor PE-Xa pipes, made of brass. Item no. d [mm] d1 [mm] d2 [mm] Description unit 1020524 20 9.9 20 Uponor PE-Xa Q&E tee reducer 20 X 9.9 X 9.9 incl. 1 PEX ring 9.9 and 2 PEX rings 20 5 pcs Uponor Q&E ring natural Made of PE-X. Uponor Q&E rings natural intended for Uponor Q&E fittings. For PE-Xa pipe dimensions 16, 20, 25, 32, 40, 50 and 63 mm. Item no. d [mm] colour [-] p [bar] Description unit 1042836 20 natural 6+10 Uponor Q&E ring natural with stop edge Uponor PE-Xa dim 20 mm 20 pcs Uponor PE-X ring for PE-Xa pipes For Uponor Minitec PE-Xa pipe 9.9 x 1.1 mm; to secure fixing to Minitec fittings Material: High-pressure cross-linked polyethylene (PE-Xa) Item no. d [mm] Description unit 1005263 9.9 Uponor PE-X ring for PE-Xa pipes 9.9 x 1.1 10 pcs 98 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor tools Uponor tools Uponor pipe cutter up to 25 mm For Uponor pipes, outside diameter up to 25 mm. Item no. d [mm] Description unit 1001369-25 Uponor pipe cutter for PEX 14-25mm Uponor pipe cutter up to 20 For Uponor pipes, outside diameter up to 20 mm with corrugated pipe cutting device. Item no. d [mm] Description unit 1006636-20 Uponor pipe cutter 14-20 mm 1006637 Uponor spare blade for pipe cutter 1006636 Uponor cutting aid For the easy cutting of Uponor pipe fixing system panels. 1016724 Uponor cutting tool for pipe positioning panel 14-16mm with insulation Uponor polystyrene cutter tool for lightweight system For cutting of individual pipe curves and guides. And also for the smooth cutting to size of polystyrene items. 230 V connection. Item no. OV [V] Description unit 1006290 230 Uponor polystyrene cutting tool for lightweight system Uponor outside bending spring MLC Special bending spring for Uponor MLC pipe. Item no. d [mm] Description unit 1006639 14 Uponor bending spring outside MLC 14 1006640 16 Uponor bending spring outside MLC 16 EEI-Int-RHC-01.12 99

Uponor Radiant Heating/Cooling > Uponor tools Uponor tools Uponor manual pressing tool MLC For pressing of Uponor press fittings MLC 14-20 mm in conjunction with exchangeable inserts. Supplied in case without exchangeable inserts. Item no. d [mm] Description unit 1015764 14-20 Uponor manual press tool MLC 14-20 incl. case without pressing inserts Uponor manual pressing tool inserts MLC For inserting into the manual pressing tool for pressing the Uponor press fittings MLCP 14/16/18/20 mm. Item no. d [mm] Description unit 1015776 14 Uponor manual press tool insert MLC 14 1 set 1015777 16 Uponor manual press tool insert MLC 16 1 set 1015780 20 Uponor manual press tool insert MLC 20 1 set Uponor press tool electric UP 75 Supplied in plastic case for the 230 V mains connection, without pressing jaws. Range of application up to 110 mm. Technical Specifications: Weight of the pressing tool: 3.30 kg Nominal voltage: 230 V DC / 50 Hz Nominal capacity: 200 Watt For dimensions: up to 110 mm Press power: ca. 32 kn Press duration: ca. 7 sec. Item no. d [mm] OV [V] Description unit 1007082-110 230 Uponor electric pressing tool UP 75 EL without pressing jaws Uponor PE-Xa pipe 9.9x1.1 expander Hand tool for the easy expansion of Uponor PE-Xa pipes 9.9 x 1.1 mm, consisting of: - 1 hand expander - 1 expander head for PE-Xa pipe 9.9 x 1.1 mm - 1 tube of lubricant - 1 case 1006247 Uponor PE-Xa pipe 9.9 x 1.1 expander tool 1 set 100 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor tools Uponor tools Uponor Q&E battery tool M12 Battery powered expander tool for 6 bar pipes up to dimension 32mm and for 10 bar pipes up to 28 mm. Auto-rotating with M12 expander heads. < 10seconds full expansion onto a joint < 2.2kg with head and battery Steel gear and integrated metal frame LED work light, fuel gauge, Tool free head change incl. 2 Li-ion 1.5 Ah batteries, charger 220-240V/50-60Hz and grease (Mo) Item no. stroke [mm] p [bar] Description unit Uponor Q&E M12 expander 1057166 14 6 with 6 bar heads 16-20-25 1 set Uponor Q&E battery tool M18 Battery powered expander tool for 6 bar pipes up to dimension 40mm and for 10 bar pipes up to 32 mm. Auto-rotating with M18 expander heads. < 10seconds full expansion onto a joint. < 2.2kg with head and battery Steel gear and integrated metal frame LED work light, fuel gauge, Tool free head change incl. 2 Li-ion 1.5 Ah batteries, charger 220-240V/50-60Hz and grease (Mo) Item no. stroke [mm] p [bar] Description unit Uponor Q&E M18 expander 1057169 25 6 with 6 bar heads H20-H25-H32 1 set Uponor Q&E M12 expander heads Q&E head for NKB fittings, for M12 and M18 tools. Expander head packed screw pack Item no. d [mm] stroke [mm] p [bar] Description unit 1057184 15 14 10 Uponor Q&E M12 expander head 14/15x2.5 mm 1057185 18 14 10 Uponor Q&E M12 expander head 17/18x2.5 mm Uponor Q&E M12 expander heads Q&E head for S5 fittings, for M12 and M18 tools. Expander head packed screw pack Item no. d [mm] stroke [mm] p [bar] Description unit 1057172 16 14 6+10 Uponor Q&E M12 expander head 16x1.8/2.0/2.2 mm 1057173 20 14 6 Uponor Q&E M12 expander head 20x1.9/2.0 mm 1057175 25 14 6 Uponor Q&E M12 expander head 25x2.3 mm EEI-Int-RHC-01.12 101

Uponor Radiant Heating/Cooling > Uponor tools Uponor tools Uponor Q&E M18 expander heads Q&E head for S5 fittings, for M18 tools. Expander head packed screw pack Item no. d [mm] stroke [mm] p [bar] Description unit 1057178 20 25 6 Uponor Q&E M18 expander head H20x1.9/2.0 mm 1057180 25 25 6 Uponor Q&E M18 expander head H25x2.3 mm 1057183 40 25 6 Uponor Q&E M18 expander head H40x3.7 mm Uponor Q&E M12 battery Q&E M12 rechargeable Li-ion battery for M12 tool. Battery 1.5 AH 1057409 Uponor Q&E battery M12 1.5 AH Uponor Q&E M12 charger Q&E M12 charger for M12 tool Charger 220-240V / 50-60Hz Item no. OV [V] Description unit 1057410 230 Uponor Q&E charger M12 220-240V Uponor Clip Stapler High-precision, wear-proof tool for pinning with staples in magazines, with curved magazine. 1002295 Uponor Clip stapler 102 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Uponor tools Uponor tools Uponor manual roller For sticking down of insulation sections and edges, takes a roll of tape. 1000142 Uponor manual roller Uponor Q&E head graphite paste Colloidal graphite paste. For Uponor Q&E Tools. 1008334 Uponor graphite paste for Uponor pliers colloidal graphite paste, 30 g/tube 20 pcs Uponor Twisting tool For twisting of the tying wires while fixing the pipe on steel meshes. 1006243 Twisting tool for tying wire Uponor cutter knife Cutter knife for polystyrene insulation. 1006263 Uponor polystyrene cutter knife Uponor ring spanner wrench For swivel nut of the Uponor compression adapters Item no. A/F [mm] Description unit 1006265 30 Uponor ring spanner wrench for wrench size 30 mm Uponor door pipe duct Expansion rod with pipe laying mount 1007179 Uponor door pipe guide EEI-Int-RHC-01.12 103

Uponor Radiant Heating/Cooling > Uponor tools Uponor tools Uponor plastic manifold valve tool For mounting and de-mounting the valves of the plastic manifold. Item no. 1009216 Description Uponor plastic manifold valve tool Uponor Tying tool Item no. 1034533 Description Twisting tool for tying wire Uponor pipe uncoiler with pipe guide For laying of all Uponor pipes up to dimension 25 mm. Suits different pipe coils with 300 mm and 600 mm internal diameter. 1035807 Uponor pipe uncoiler with pipe guide Uponor snow and ice decoiler Uponor snow and ice melting, pipe decoiler. 1033691 Uponor Meltaway decoiler for 25 x 2,3 mm pipe 104 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > International sales and delivery terms International sales and delivery terms 1 Interpretation 2 Basis of the sale 3 Orders and specifications 4 Price of Goods 5 Terms of payment 6 Delivery and Performance EEI-Int-RHC-01.12 105

Uponor Radiant Heating/Cooling > International sales and delivery terms International sales and delivery terms 7 Risk and property 8 Liability 9 Insolvency of Buyer 10 Packing 11 General 106 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Item search register Item search register Item no. unit Page 1000002 m² 23 1000003 m² 23 1000012 pcs 20 1000015 m² 23 1000016 pcs 40 1000017 m² 23, 33 1000018 m 24 1000019 pcs 24 1000079 m 39 1000080 m 39 1000081 m 39 1000082 pcs 39 1000083 pcs 40 1000084 l 40 1000085 l 41 1000138 pcs 59 1000142 pcs 103 1000296 pcs 91 1000297 pcs 92 1000298 pcs 92 1000299 pcs 92 1000300 pcs 92 100030 92 1000303 pcs 92 1000304 pcs 92 1000310 pcs 93 100031 94 1000312 pcs 95 1000313 pcs 95 1000314 pcs 95 1000502 pcs 52 1000503 pcs 52 1000504 pcs 52 1000505 pcs 52 1000515 pcs 54 1000516 pcs 66 1000517 pcs 66 1000518 pcs 54 1000527 pcs 53 1000529 pcs 54 100053 56 1000533 pcs 56 1000535 pcs 57 1000536 pcs 57 1000537 pcs 59 1000538 pcs 53 1000539 pcs 57 1001369 pcs 99 1002295 pcs 102 1002296 pcs 23 1002297 pcs 23 1002356 pcs 66 1002357 pcs 66 1005049 m² 12, 33, 40 1005066 l 41 Item no. unit Page 1005084 m² 33 1005087 m² 33 1005100 set 46 1005168 pcs 47 1005170 pcs 47 1005261 m² 9 1005263 pcs 9, 37, 98 1005264 pcs 9, 36, 97 1005265 pcs 9, 37, 97 1005266 pcs 46 1005267 m 10 1005268 m 10 1005269 pcs 10, 40 1005274 m 10, 36 1005284 pcs 85 1005286 pcs 85 1005287 pcs 33, 74, 81 1005289 pcs 74 1005290 m 73, 81 100529 73, 81 1005295 pcs 72, 82 1005296 pcs 72, 82 1005297 pcs 72, 82 1005298 pcs 72, 82 1005358 m 73 1005372 pcs 74, 81 1005477 m² 15 1005478 m² 15 1005479 m 15 1005480 m 15 1005481 m 16 1005482 pcs 16 1005483 m 16 1005484 m 16 1005485 m² 12 1005486 pcs 12 1005498 m 24 1005576 pcs 68 1005605 pcs 61 1005675 set 68 1006243 pcs 103 1006247 set 100 1006263 pcs 103 1006265 pcs 103 1006290 pcs 99 1006636 pcs 99 1006637 pcs 99 1006639 pcs 99 1006640 pcs 99 100664 46 1007082 pcs 100 1007179 pcs 103 1007226 m² 20 1007228 m² 20 1007232 m² 20 Item no. unit Page 1007234 m² 20 1008334 pcs 103 100867 72, 84 1008673 pcs 86 1008683 pcs 86 1008932 pcs 72 1008939 m 86 1009004 pcs 48 1009006 pcs 74, 82, 87 1009129 pcs 38 1009132 pcs 38 1009209 set 44 1009214 set 44 1009215 set 44 1009216 pcs 104 1009217 pcs 44 1009222 pcs 33, 74, 82 1009226 m 17, 25, 34 1009227 m 17, 25, 34 1009228 m 25, 34, 36 1009230 m 25,34,36,72,97 1009231 m 25,34,36,72,97 1009233 pcs 48, 74 1012869 m 74, 82, 87 1013005 pcs 60 1013006 pcs 61 1013008 pcs 59 101305 45 1013052 pcs 45 1013053 pcs 45 1013054 pcs 45 1013055 pcs 45 1013056 pcs 45 1013057 pcs 45 1013058 pcs 45 1013059 pcs 45 1013060 pcs 45 101306 45 1013062 pcs 45 1013063 pcs 45 1013064 pcs 45 1013065 pcs 45 1013066 pcs 45 1013067 pcs 45 1013068 pcs 45 1013069 pcs 45 1013070 pcs 45 101307 45 1013072 pcs 45 1013127 m 24 1013366 m 13, 18, 26, 31 1013371 m 18, 26, 31 1013378 m 18, 26, 31 1013380 m 18, 26, 31 1013392 m 26 EEI-Int-RHC-01.12 107

Uponor Radiant Heating/Cooling > Item search register Item search register Item no. unit Page 1014122 pcs 47 1015154 pcs 13, 18, 26, 31 1015164 pcs 18, 21, 26, 31 1015187 pcs 26 1015764 pcs 100 1015776 set 100 1015777 set 100 1015780 set 100 1016699 m² 28 1016700 m² 29 1016701 m² 29 1016702 m² 30 1016703 m² 28 1016724 pcs 99 1020506 pcs 97 1020518 pcs 37, 98 1020524 pcs 37, 98 1022341 m 78 1022983 pcs 90 1022984 pcs 90 1022985 pcs 93 1022986 pcs 93 1022987 pcs 91 1022988 pcs 93 1023006 pcs 73 1023007 pcs 73, 84 1023008 pcs 73, 84 102301 73 1023012 pcs 73, 84 1023013 pcs 73, 84 1023448 m 72, 84 1030134 pcs 76 1030135 set 76 1030580 pcs 43 103058 43 1030582 pcs 43 1030583 pcs 43 1030584 pcs 43 1030585 pcs 43 1032701 set 46 1032702 set 44 1033024 m 9, 36 1033025 m 9, 36 1033026 m 9, 36 1033625 m 78 1033626 m 78 1033628 m 79 1033629 m 79 1033630 m 79 103363 78 1033632 pcs 78 1033633 pcs 78 1033634 pcs 79 1033635 pcs 79 1033636 pcs 79 Item no. unit Page 1033637 pcs 78 1033638 pcs 78 1033639 pcs 78 1033640 pcs 78 103364 78 1033642 pcs 78 1033643 pcs 78 1033644 pcs 79 1033645 pcs 78 1033646 pcs 79 1033647 pcs 78 1033648 pcs 79 1033649 pcs 79 1033650 pcs 79 1033652 pcs 80 1033653 pcs 80 1033654 pcs 80 1033657 pcs 80 1033659 pcs 80 1033660 pcs 80 103366 80 1033662 pcs 80 1033663 pcs 80 1033666 pcs 81 1033667 pcs 81 1033668 pcs 81 1033672 pcs 79 1033673 pcs 81 1033675 pcs 81 1033676 pcs 81 1033678 pcs 79 1033689 pcs 82 103369 104 1033975 pcs 48 1034533 pcs 104 1034535 m 17, 25, 34 1035807 pcs 104 1042389 pcs 18, 21, 26, 31 1042420 set 43 1042471 set 43 1042836 pcs 79, 98 1042837 pcs 26, 34, 37 1042840 pcs 73, 84 1042942 pcs 93 1042943 pcs 93 1042944 pcs 93 1042945 pcs 93 1042946 pcs 94 1042947 pcs 94 104418 33 1044809 pcs 93 1044810 pcs 93 104481 93 1044812 pcs 93 1045315 pcs 89 Item no. unit Page 1045316 pcs 89 1045317 pcs 89 1045318 pcs 89 1045319 pcs 90 1045320 pcs 90 1045323 pcs 90 1045324 pcs 90 1045325 pcs 91 1045326 pcs 91 1045327 m 91 1045328 pcs 91 1045464 pcs 86 1045562 set 51 1045565 pcs 51 1045568 pcs 52 1045570 pcs 53 104557 54 1045572 pcs 53 1045813 set 75 1045814 set 75 1045815 set 75 1045816 set 76 1046114 pcs 52 1046115 pcs 52 1046747 set 85 1046748 set 85 1046749 set 85 1046870 pcs 68 104699 48 1046992 pcs 48 1046993 pcs 48 1046994 pcs 48 1046996 pcs 49 1046997 pcs 49 1046998 pcs 49 1046999 pcs 49 1047000 pcs 48 1047319 pcs 97 1047320 pcs 97 104732 97 1047610 m 17, 25, 30 1047611 m 17, 25, 30 1047612 m 17, 25, 30 1047615 m 72, 84 1047618 m 72, 84 1047624 m 21 1047625 m 21 1047844 pcs 64 1047845 pcs 65 1047846 pcs 65 1047847 pcs 66 1047848 pcs 66 1047867 pcs 86 1048010 pcs 56 104801 58 108 EEI-Int-RHC-01.12

Uponor Radiant Heating/Cooling > Item search register Item search register Item no. unit Page 1048012 pcs 58 1048013 pcs 59 1048249 m 21 1048290 m 12, 17, 25, 30 1048291 m 12, 17, 25, 30 1048395 m 21 1048684 pcs 92 1048685 pcs 92 1048763 pcs 66 1048780 pcs 69 104878 69 1048782 pcs 70 1048783 pcs 70 1052123 pcs 80 1056656 pcs 80 1057166 set 101 1057169 set 101 1057172 pcs 101 1057173 pcs 101 1057175 pcs 101 1057178 pcs 102 1057180 pcs 102 1057183 pcs 102 1057184 pcs 101 1057185 pcs 101 1057368 pcs 47 1057370 pcs 47 1057409 pcs 102 1057410 pcs 102 105744 47 1057442 pcs 47 1058089 pcs 47 1058090 pcs 47 105809 47 1058092 pcs 47 1058422 pcs 60 1058423 pcs 60 1058424 pcs 61 1058425 pcs 61 1058426 pcs 60 1058427 pcs 60 1058428 pcs 13, 18, 26, 31 1058429 pcs 18, 26, 34 1058659 pcs 13, 18, 26, 31 1058660 pcs 18, 21, 26, 31 105866 18, 26, 34 1058668 pcs 26, 34 EEI-Int-RHC-01.12 109

Notes 110 EEI-Int-RHC-01.12

How to contact us Customer Service Center T + 49 (0)9521-690-370 F + 49 (0)9521-690-750 E export@uponor-europe.com Technical assistance T +49 (0)9521-690-739 or 834 F +49 (0)9521-690-750 E export@uponor-europe.com Export Department T +49 (0)9521-690-370 F +49 (0)9521-690-750 E export@uponor-europe.com We reserve the right to make technical amendments and carry out updates. EEI-Int-RHC-01.12 111

Uponor partnering with professionals Uponor is a leading supplier of plumbing and heating systems for the residential and commercial building markets across Europe and North America, and a market leader in municipal infrastructure pipe systems in the Nordic countries. Uponor's key applications include indoor climate and plumbing systems. Uponor International Sales takes care of all business activities in the Balkans, Western, Central and East Asia, Africa and Latin America. Uponor. Simply more. 01/2012 Subject to modifications Uponor GmbH P.O. Box 1641 97433 Hassfurt Germany T +49-(0)9521 690 0 F +49-(0)9521 690 750 E international@uponor.com W www.uponor.com/international