NELE POITIONER ELECTRO-PNEUMATIC ERIE NE700 PNEUMATIC ERIE NP700 The NE700 and NP700 are proportional positioners for control valves. The NP is a fully pneumatic unit while the NE is an electro-pneumatic unit that provides pneumatic output proportional to a standard milliampere DC input. Both units can be used with either cylinder or diaphragm type actuators for rotary or linear valves to provide excellent repeatability and accuracy in a wide range of throttling applications. FEATURE Excellent vibration resistance Rugged construction, few parts, small moving mass, compact design and rigid mounting provide outstanding vibration resistance. Field reversible Positioner can be set for direct or reverse-acting modes by simply turning around the changeover piece and feedback cam without touching or changing tubings between actuator and positioner. plit-range and reverse actions are standard on the feedback cam. Easy and fast to calibrate Calibrations can be easily made with the positioner cover removed. You can fine-tune zero and range adjustments with minimal effect on set points. Fast response times Multiple pilot valve sizes are used to match positioner capacity compatible with actuator stroke volume, minimizing response time. table operation Changes in supply pressure and valve load have minimal effect on positioner operation. Intrinsically safe Intrinsically safe option available for hazardous areas to CA Class I, Group A, B, C and D. NE positioners These electro-pneumatic positioners operate on a milliampere signal from a controller. They accurately position the control valve assembly in response to a change in input signal. The nominal input resistance is 190 ohms. The moving force coil assembly has low mass and is accurately balanced to assure proper function even in severely vibrating applications. The dynamic behaviour of the positioner can be changed by choosing different size pilot valves (see table in page 3) and adjusting the internal gain. NP positioners The NP positioner operates on a pneumatic signal. It responds to a change in pneumatic instrument signal and accurately re-positions the control valve assembly. The diaphragm piston and feedback spring are force balanced. The rugged beam and few parts provide excellent vibration resistance. The positioner capacity can be changed by choosing different size pilot valves (see table in page 3). NE and NP positioners The direction of operation for NE or NP positioners can be changed simply by reversing the built-in changeover piece and the cam. External piping need not to be modified. The same housing is utilized for both styles of positioner and in both double-acting and single-acting versions. CE-mark NE700 positioner carry the CE-mark concerning the countries which belong to the European Economic Area. Options intrinsically safe construction. CA Class I, Group A, B, C and D (only NE series). protection through constructional safety ATEX II G c (only NP series) flame proof enclosure ATEX approved (II G EEx d IIC T4/T5/T6) or FM and CA approved (Class I, II, Div. 1, Gr. B - G) (only NP series). dust proof enclosure (IP 65). electric plug connector D 43650/IO00. high temperature construction up to +10 C / +50 F. natural gas service. pressure gauge kit. bypass kit (only NP series). filter regulator. attachment to rotary actuators to VDI/VDE 3845. 7 NE/NP 0EN Issue 11/005
METO AUTOMATION NE Principle of operation 1 = beam = diaphragm piston 3 = feed-back spring 4 = lever 5 = cam 6 = feedback shaft 7 = coupling 8 = actuator shaft 9 = actuator = pilot valve spool 11 = pilot valve body 1 = zero adjustment 13 = internal feed-back spring = changeover piece 15 = force coil 16 = permanent magnet 17 = balance beam = nozzle 19 = restriction 0 = range adjustment = supply pressure = cylinder pressure = nozzle & diaphragm pressure = fixed parts = moving parts 11 19 0 1 13 17 3 4 1 16 5 15 6 7 9 8 The force coil (15) located in the permanent magnetic field creates a torque proportional to the signal current on the balance beam (17). The feed-back spring (3) causes a countertorque on the balance beam (17) in relation to the turning angle of the actuator shaft. Turning is transmitted through coupling (7), feed-back shaft (6), cam (5) and lever (4) to the lower end of the feed-back spring (3). Nozzle () senses the torque balance on beam (17). When, e.g., the signal increases, the beam will close the nozzle () further, the nozzle pressure will increase and the diaphragm piston (), beam (1) and spool () will move downwards. The pilot valve (, 11) distributes air flow to the upper side of the actuator piston and from the lower side to the exhaust port. Due to the pressure difference, the piston force overcomes friction and dynamic torques and moves the actuator shaft in to a position corresponding exactly to the new signal. Torques on the beam (17) are then in balance. The spring (13) causes a negative feed-back between the first amplification stage consisting of nozzle (), restriction (19) and diaphragm piston () and the second amplification stage consisting of pilot valve (, 11) and actuator. By changing the lower fastening point of the spring (13) along the beam (17), the dynamics of the positioner can be adapted according to the actuator side. Differential diaphgrams effectively compensate the influence of supply pressure variations. Zero is adjusted with a nut (1) and range with a potentiometer (0). NP Principle of operation 1 = beam = diaphragm piston 3 = feed-back spring 4 = lever 5 = cam 6 = feedback shaft 7 = coupling 8 = actuator shaft 9 = actuator = pilot valve spool 11 = pilot valve body 1 = range adjustment nut 13 = zero adjustment screw = changeover piece 11 1 1 3 9 = supply pressure = cylinder pressure 8 = signal pressure = fixed parts 4 7 = moving parts 13 5 6 Operation is based on the force balance principle. One force is caused by signal pressure () transmitted through the diaphragm (), the other force is caused by the feedback spring (3). The latter is directly proportional to the position of the lower end of the spring, this in turn, is depend solely on the actuator shaft (8) position as transmitted through the coupling (7), shaft (6), cam (5), and the lever (4). When these forces are not equal, the beam (1) moves in the direction of the stronger force. The end of the beam moves the spool () in the body (11). Diverted from the balance position, the spool () guides supply air to one side of the piston and exhaust air from the other, causing a pressure difference in cylinder (9). The piston moves in the direction of the lower pressure until the tension induced in the feed-back spring by this change counterbalances the force caused by the change in signal pressure. Every signal pressure value corresponds to only one actuator position. In the balanced position, the pressure on both sides of the unloaded actuator's piston is approximately equal, being about 0.7 times the supply pressure. If an external torque acts on the actuator the shaft tends to move towards the torque direction. Through the feed-back system this will produce a change in the position of the spool so that the pressure difference created in the cylinder will counterbalance the external torque. - -
NELE POITIONER ELECTRO-PNEUMATIC ERIE NE700 PNEUMATIC ERIE NP700 TECHNICAL PECIFICATION NE700 technical data tandard input signal 4-0 ma, 0-0 ma (direct current) plit ranges 4-1 ma, 1-0 ma Input resistance max. 190 Ω Turning angle of feedback shaft max. 95 Relation between turning angle and signal linear upply pressure p s 0. - 0.8 MPa 1.4-8 barg / 0-115 psig Effect of supply pressure p s <0. %/ kpa / 0. %/psi Ambient temperature -5 to 85 C / -15 to 5 F Effect of temperature <0.05 %/ C / <0.05 %/ F Performance with moderate constant load actuators - dead band < 0.3 % - hysteresis < 0.7 % - linearity < % Effect on vibration (1.5 g, 5-0 Hz) < 1 % Construction materials: - Case is anodized aluminium alloy, epoxy coated. - Cover is polycarbonate or aluminium alloy. Internal parts are stainless steel and aluminium alloy. - Diaphragms and seals are nitrile rubber (standard model). Weight approx..3 kg / 4.8 lbs NP700 technical data tandard signal pressure ranges plit ranges Turning angle of feedback shafts max. 95 Relation between turning angle 0-0 kpa 0. - 1.0 barg / 3-15 psig 0 - kpa, - 0 kpa 3-9 psig, 9-15 psig and signal linear upply pressure p s 0. - 1 MPa 1.4 - barg / 0-0 psig Effect of supply pressure <0. %/ kpa / 0. %/psi Ambient temperature -40 to 90 C / -40 to 00 F Effect of temperature <0.07 %/ C / <0.05 %/ F <0.15%/ C / <0.05 %/ F Performance with moderate constant load actuators - dead band < 0.3 % - hysteresis < 1. % - linearity < % Effect on vibration (1.5 g, 5-0 Hz) < 1 % Construction materials: - Case is anodized aluminium alloy, epoxy coated. - Cover is polycarbonate or aluminium alloy. Internal parts are stainless steel and aluminium alloy. - Diaphragm and seals are nitrile rubber (standard model). Weight approx. 1.6 kg / 3.3 lbs Metso Automation Actuator/Positioner election Chart Actuator type NE NP B1JU8, QP1 & QP Quadra-Powr, RA/DA diaphragm actuator NE79 NP79 B1CU6 thru B1CU11 NE74 NP73 B1CU13 thru B1CU0, B1JU thru B1JU16 QP3 & QP4 Quadra-Powr DA/RA thru DB/RB diaphragm (linear) NE74 NP74 B1CU5, B1CU3, B1JU0, B1JU5, QP5 QP6 Quadra-Powr DC/RC thru DD/RD and DE/RE diaphragm (linear) A46/A47 NE7 NP7 B1CU40 & larger, B1JU3 & larger QP7 NE77 NP77 EC05_U NE74 NP73 EJ05_U NE79 NP79 EC07_U... E_U; EJ07_U... E0_U NE74 NP73 E4_U; EJ1_U... EJ_U NE74 NP74 Positioner model Pilot valve alternatives Actuator wept Volume dm 3 (litres) Consumption m 3 n /h/scfm * Delivery m 3 n /h/scfm* NE79 1) 0.3-1.0 0.7 0.4 1.0 7.0 NE74 1.0-8.0 0.9 0.5 1.0 7.0 NE7 8.0-30.0 1. 0.7.0.4 NE77 > 30.1 1. 3.0.6 NP79 1) 0.3-1.0 0.4 0. 1.0 7.0 NP73 0.3-1.0 0.6 0.3 1.0 7.0 NP74 1.0-8.0 0.6 0.3 1.0 7.0 NP7 8.0-30.0 0.9 0.5.0.4 NP77 > 30 1.8 1.0 3.0.6 *) upply pressure at 0.4 MPa 4 barg / psig. (max. air delivery capacity) 1) Only for spring-return actuators B1JU8, QP1 & QP. - 3 -
METO AUTOMATION Dimensions - mm / inch for Electro-pneumatic positioner - NE700 3/4NPT 40 1.57 NE700/XGN 5 0.98 NE700/R.8 1.06 Ø6 ø0.4 0.55 0.39 1.0 36 1.4 56.0 7 4.1 0.06 NE700A 0 0.78 F05-ø50 M6/ (35.4) (1.39) NE700/1 4. 5 5.71 1/NPT = NE700-L, NE700/U M0x1,5 = NE700-I R1/ = NE700-NJ 45 6.4 0.5 4 0.94 4. 5/16UNC/13 6 30. 0.71 1.0 1. 89 3.50 45 1.77 1.0 31 1. () (1.0) 0.71 D 43650 IO 00 1.0 NE700/P 1 0.48 (45) (1.77).09 NE77 3/8NPT 1/4 NPT 70.77 () 36 1.4 1 4.49 Dimensions - mm / inch for Pneumatic positioner - NP700 Ø40 ø1.57 () () () 16.5 0.65 NE700-K NE700/A 64.5 83 3. Ø40 ø1.57 38 1.49 46 1.81 177 6.97 0.38 34 1. 58. 9 1. 3/4NPT 40 1.57 NP700/GN 5 0.98 NP700/R.8 1.06 36 1.0 1.4 4. Ø50 ø1.96 (35.4) (1.39) 0.69 70.77 NP700-K Ø6 ø0.4 0.55 7 4.1 NP700/1 5/16UNC/13 M6/ 5 4.3 5.71 (45) (1.77) 3/8NPT 1.11 () Ø40 ø1.57 83 3.7 177 6.97 6.4 0.5 NP77 0 0.79 45 64.5 () () () 16.5 0.65 () 31 1. NP700/B,M0x1.5 NP700/B1,1/NPT 30 1. 0.08 7 4.1 NP700A 6 30. 0.71 89 1.0 1. 3.50 4 1.65 Ø40 ø1.57 0.55 0.39 ø75 ø.95 1 6.30 55.16 36 1.4 1 4.49 NP700/A 38 1.49 46 1.81 4. 40 9.45.8 1.05 1.4 36 1.4 F05-ø50 0.71 ø 6 M6/ ø 0.4 7 (35.4) NP700/B1 0.55 4.1 (1.39) 5 4. 5.71-4 -
NELE POITIONER ELECTRO-PNEUMATIC ERIE NE700 PNEUMATIC ERIE NP700 Dimensions - mm / inch for Electro-pneumatic positioner and limit switch combination NEK700/NEI700 5/16UNC/13 NE_700A/700 45 6.4[0.5] 15 0.59.09 NEK700/1/700 NEI700/1/700 4 0.94 0.06 0 0.79 45 1.77 6. 89 3.50 30 1.01. 0.71 (45) (1.77) 31 1. 3/8NPT 1 0.47 NEK700/../700/P NEI700/../700/P 69.7.08 D 43650/IO 00 [1.0] 36 1.4 ø6.8 1.06 ø0.4 0.56 56.0 77 3.03 41.5 1.63 35 1.38 PG13.5 175 6.88 1 3.97 NET700/../700 F05-ø50 4. 5 5.71 M6/ (35.4) 1.39) 0.70 4. 1.0 1.0 1.0 1/NPT = -L M0x1,5 = -I R1/ = -NJ 1 0.48 NE_77/700 NE_700/P... D 43650 IO 00 Ø58 Ø..09 06 8.11 34 1.34 Dimensions - mm / inch for Pneumatic positioner and limit switch combination NPK700/NPI700 NP_700A/700 5/16UNC/13 15 0.59 NPK700/1/700 NPI700/1/700 0.06 0 0.88 6. 89 3.50 1.030.71 30 1. (45) (1.77) 3/8NPT NPK700/../700/P NPI700/../700/P 69.7 4. NP_77/../700 1 0.47 PG13.5 M6/ D 43650/IO 00 NPT700/../700 Ø 58 ø. 6.4 0.5 0.39 34 1.34 45 31 1..09 36 1.0 1.4 1 3.96.09.8 1.05 ø 0.55 Ø6 0.4 77 3.03 97.5 3.84 175 6.88 35 1.38 06 8.11 34 1.34-5 -
METO AUTOMATION AVAILABLE OPTION Pressure Gauge Kit tainless steel gauges, diameter 40 mm, Type code: NE7 /A1, NP7 /A1. Bypass kit Type code: NP7 /A11. Filter regulator Die-cast aluminium. No brass parts. Rugged and corrosion resistance. Output pressure range 0-700 kpa 7 barg / 0 psig. Maximum supply pressure 1750 kpa 17. 5 barg / 50 psig. Type code: NE7 /-K, NP7 /-K. Flame proof enclosure ATEX approval: II G EEx d IIC T4/T5/T6 Type code: NP70 /B1. FM and CA approval: Class I, II, Div. 1, Gr. B - G Type code: NP70 /B11. Input signal 4-0 ma.. upply pressure 00-00 kpa - barg / 30-5 psig. Positioner for linear (globe) valves Applicable to Metso Automation diaphragm actuator. DA/RA thru DB/RB DC/RC thru DD/RD and DE/RE. tandard stroke 19-57 mm/ 3/4-1/4 inch. Other strokes available on request. Type code: NE7 A, NP7 A. Combination of positioner and limit switch All the same features as the basic positioners or limit switches. Type code: NEK7.../.../7... or NEI7.../.../7... NPK7.../.../7... or NPI7.../.../7... ee bulletin 7N0. - 6 -
NELE POITIONER ELECTRO-PNEUMATIC ERIE NE700 PNEUMATIC ERIE NP700 HOW TO ORDER NE700 POITIONER 1.. 3. 4. 5. 6. NE 7 6 / 1A KCE1 Example: This is a single-acting electro-pneumatic positioner for a 4-0 ma input signal, with 6 mm pilot, pressure gauge kit and 1/ NPT conduit entry with filter regulator. 1. sign PRODUCT GROUP NE Electro-pneumatic positioner.. sign ERIE CODE 3. sign PUT IGNAL RANGE 4-0 ma; 0-0 ma. 4. sign PILOT VALVE CONNECTION (,, ) 4 Ø 4 mm 1/4 NPT 6 Ø 6 mm 1/4 NPT 7 Ø 6 mm HC 3/8 NPT 9 Ø 4 mm LC 3-way pilot valve, single action, applicable only with B1JU8, QP 1, QP and DA/RA. 5. sign always to be specified, or A. 1/4 NPT 6. sign OPTION If several options below are needed to the same positioner, the codes shall be marked in presented order from top. Temperature range for various options shall be considered carefully. U XU ZU XUGN ZUGN R W H 1 A P Y C tandard, IP 54 enclosure. PG 11 conduit entry. 1 always to be defined. Temperature range -5 ºC... +85 ºC / -13 F...+5 F. CA-standard construction, 1/ NPT conduit entry. Temperature range -5 ºC... +85 ºC / -13 F...+5 F. Intrinsically safe construction, CA Class I Div. 1 Groups A, B, C, D -certification. 1/ NPT conduit entry. Temperature range -5 C... + C / -13 F...+0 F. CA Class I Div. Groups A, B, C, D -certification, 1/ NPT conduit entry. Temperature range -5 ºC... +85 ºC / -13 F...+5 F. For natural gas. Exhaust adapter, 3/4 NPT-thread. Temperature range see XU, ZU. Water and dustproof enclosure. IP65 / NEMA 4 and 4X. Not available with options XUGN, ZUGN. Better vibration resistance. pecial flexure pivot and diamond coated pilot. Not available with options U, XU, ZU. High temperature construction. Viton diaphragms and seals. Temperature range - ºC... +10 ºC / + F... +48 F. Not available with options U, XU, ZU, A, P and accessory K. Positioner attachment face according to stadard VDI/VDE 3845, equipped with an H-clip. When positioners are separate deliveries, VDI/VDE ear is supplied. Not applicable to globe valve actuators (5. sign A). Pressure gauges, scale bar/psi/kpa, basic material brass, nickel plated, housing stainless steel, glycerine filled. 5. sign always to be defined. Temperature range -5 ºC... +70 ºC / -13 F... +158 F. Connection plug acc. to D 43650A/IO 00 (PG 11). Not available with options U, XU, ZU and accessories L, I, NJ. pecial construction, to be specified. pecial cam, to be defined in order. 5. sign ACTION Double action, without sign. A ingle action. Will be specified in the option sticker. ingle action, linear motion. Applicable ONLY to D/R series spring diaphragm linear actuators, max. stroke size 57 mm (-1/4 in). - ACCEORIE K CE01 CE0 CE03 Filter regulator for supply air, type BELLOFRAM T51FR. Pressure gauge, scale bar/psi/kpa, basic material brass, nickel plated, housing stainless steel, glycerine filled. Temperature range -40 ºC... +8 ºC / -40 F... +0 F. Filter size 5 µm. Not available with HC-pilot (4. sign 7). Will be specified in the option sticker. In connection with the Ø6 HC-pilot valve (4. sign 7) must be used large capacity filter regulator (not K) for actuator bigger than B1CU40 and B1JU 3. Installation with mounting bracket. / 1/ NPT conduit entry nipple. Will be specified in the option sticker. / M0x1.5 conduit entry nipple. Will be specified in the option sticker. / R1/ (PF1/) conduit entry nipple. Will be specified in the option sticker. - 7 -
METO AUTOMATION HOW TO ORDER NP700 POITIONER 1.. 3. 4. 5. 6. NP 7 4 / GN1 K Example: This is a double-acting pneumatic positioner for a 0-0 kpa / 3-15 psig input signal, with 4 mm pilot and optional exhaust adapter 3/4 NPT-thread with filter regulator. 1. sign PRODUCT GROUP NP Pneumatic positioner.. sign ERIE CODE 3. sign PUT IGNAL RANGE 0 4-0 ma, only with options B and B1 (6.sign). 0-0 kpag, 0.-1.0 barg/3-15 psig. 4. sign PILOT VALVE CONNECTION (,, ) 3 Ø 4 mm LC 1/4 NPT 4 Ø 4 mm 1/4 NPT 6 Ø 6 mm 1/4 NPT 7 Ø 6 mm HC 3/8 NPT 9 Ø 4 mm LC 3-way pilot valve, single action, applicable only with B1JU8, QP 1, QP and DA/RA. 5. sign always to be specified, or A. 1/4 NPT 6. sign OPTION If several options below are needed to the same positioner, the codes shall be marked in presented order from top. Temperature range for various options shall be considered carefully. B B1 GN R H 1 A Y C tandard, (IP 54 enclosure). 6. sign 1 always to be defined. Temperature range -40 ºC... +90 ºC/ -40 F...+194 F. Flameproof enclosure I/P-converter (IP65), ATEX EEx d IIC T6. Input signal range 4-0 ma. M0x1,5 conduit entry. 3. sign always 0. Temperature range -40 ºC... +55 ºC / -40 F...+131 F. Explosion proof enclosure I/P-converter (IP65), FM/CAapproval. Class 1, Div. 1, Groups B, C, D. Input signal range 4-0 ma. 1/ NPT conduit entry. 3. sign always 0. Temperature range -40 ºC... +55 ºC/ -40 F...+131 F. For natural gas. Exhaust adapter, 3/4 NPT-thread. Not usable inside with options B and B1! Water and dustproof enclosure. IP65 / NEMA 4 and 4X. Not available with option GN. High temperature construction. Viton diaphragm and seals. Not available with options B, B1, A, A1 and accessory K. Temperature range - ºC... +10 ºC / + F... +48 F. Positioner attachment face according to standard VDI/VDE 3845, equipped with an H-clip. When positioners are separate deliveries, VDI/VDE ear is supplied. Not applicable to globe valve actuators (5. sign A). Pressure gauges, scale bar/psi/kpa, basic material brass, nickel plated, housing stainless steel, glycerine filled. 5. sign always to be defined. Temperature range -40 ºC... +70 ºC / -40 F... +158 F. pecial construction, to be specified. pecial cam, to be defined in order. - ACCEORIE K Filter regulator for supply air, type BELLOFRAM T51FR. Pressure gauge, scale bar/psi/kpa, basic material brass, nickel plated, housing stainless steel, glycerine filled. Temperature range -40 ºC... +8 ºC / -40 F... +0 F. Filter size 5 µm. Not available with HC-pilot (4. sign 7). Will be specified in the option sticker. 5. sign ACTION Double action, without sign. A ingle action. Will be specified in the option sticker. ingle action, linear motion. Applicable ONLY to D/R series spring diaphragm linear actuators, max. stroke size 57 mm (-1/4 in). CE01 CE0 CE03 In connection with the Ø6 HC-pilot valve (4. sign 7) must be used large capacity filter regulator (not K) for actuator bigger than BC 40 and BJ 3. Installation with mounting bracket. / 1/ NPT conduit entry nipple. Will be specified in the option sticker. / M0x1.5 conduit entry nipple. Will be specified in the option sticker. / R1/ (PF1/) conduit entry nipple. Will be specified in the option sticker. ubject to change without prior notice. Metso Automation, Field ystems Europe, Levytie 6, P.O. Box 3, 00811 Helsinki, Finland. Tel. +358 0 483 150. Fax +358 0 483 151 North America, Bowditch Drive, P.O. Box 80, hrewsbury, MA 01545, UA. Tel. +1 508 85 000. Fax +1 508 85 817 Latin America, Av. Independéncia, 500- Iporanga, 087-1, orocaba-ão Paulo, Brazil. Tel. +55 15 335 9700. Fax +55 15 335 9748/49 Asia Pacific, 38A Thomson Road, #5-09 Novena quare Tower A, 307684 ingapore. Tel. +65 6511 11. Fax +65 650 0830 Middle East, Roundabout 8, Unit AB-07, P.O. Box 17175, Jebel Ali Freezone, Dubai, United Arab Emirates. Tel. +971 4 883 6974. Fax +971 4 883 6836 www.metsoautomation.com