DORMA GmbH + Co. KG DORMA Platz ENNEPETAL DEUTSCHLAND Tel Fax

DORMA GmbH + Co. KG DORMA Platz 1 58256 ENNEPETAL DEUTSCHLAND Tel. +49 2333 793-0 Fax +49 2333 793-4950 www.dorma.de DORMA-Glas GmbH Max-Planck-Straße 33 45 32107 BAD SALZUFLEN DEUTSCHLAND Tel. +49 5222 924-100 Fax +49 5222 924-3100 www.dorma.de WN 05414751532 12/13 HSW/FSW GB x XX xx/13

HORIZONTAL SLIDING WALLS HSW FSW

HORIZONTAL SLIDING WALLS HSW TRANSPARENT VERSATILITY Horizontal sliding walls are used in a wide range of different project types, and for both internal and external applications. These partitions can be flexibly designed to suit the site of installation, structural conditions and design concept. They can satisfy a broad spectrum of requirements in relation to styling, material and finish or colour, and can also be equipped with individually fabricated panels to perform special functions. Additional utilisation of the DORMA substructure ensures flexible planning in the case of all system variants as well as providing for the simple installation, maximum reliability and outstanding safety of the entire system. HSW - Horizontal Sliding Walls Panels slide individually stacking track required HSW-G Fully glazed with door rails HSW-MR Panel types and functions HSW-GP Single-point fixings with standard track rail HSW Horizontal Sliding Walls, fully framed Panels slide individually stacking track required HSW-R Fully framed for toughened safety glass, laminated safety glass or double glazing HSW-ISO Fully framed with thermal-break frame profiles FSW Folding Sliding Walls Panels slide individually stacking track required FSW-G FSW-G Fully glazed with door rails FSW-C FSW-C Roller carrier position at door rail centre FSW-C plus Roller carrier position at door rail centre plus full-width sliding folding panel FSW-C plus 2 DORMA

HORIZONTAL SLIDING WALLS CONTENT HSW Support and Guide Elements Parking And Stacking Example Stacking Arrangements Stacking Arrangement Calculations Track Rails Substructure 4 9 10 13 14 19 HSW / FSW Panel Systems HSW-G HSW-MR HSW-GP FSW-G FSW-C/C Plus HSW-R HSW-ISO 20 34 36 42 44 49 50 55 56 63 64 72 74 82 Accessories Vertical Seals Overview Vertical Sealing Profiles Floor Track 86 87 88 95 96 97 General Information Measuring Up General Information 100 101 102 Subject to change without notice DORMA 3

SUPPORT AND GUIDE ELEMENTS STACKING SYSTEMS Perfect parking every time Existing structures or unusual layouts often require special solutions, particularly in the design of the stacking area. DORMA HSW systems can be parked in a range of different positions. The stack of panels can be aligned parallel or square to the frontage, be readily visible for effect or hidden behind columns etc. Another possibility is that of parking the system in line but out of the way, whether behind a wall or in a niche (see also pages 5 9). The panels can also perform certain functions when the frontage is open, such as providing the sides of internal store windows and showcases, or, if provided with the appropriate printing on the glass, for adding artistic value to a wall. The following pages show some system solutions devised in answer to a wide range of different problems. 4 DORMA

EXAMPLE STACKING ARRANGEMENTS Panels stacked 90 transverse to travel direction Standard stacking arrangement. With pivoting end panel as possible access leaf (left or right, or left and right). Stacking in a box/pocket. Sliding panels or double action panels only (left or right, or left and right). Niche parking. With pivoting end panel as possible access leaf (left or right, or left and right). Stacking with reshuffle bypass (without pivoting end panel). Behind wall projection/fixed side panel (Left or right, or left and right). Not for HSW-MR. Stacking track 135 behind column. With end panel as possible access leaf (left or right, or left and right). Stacking behind end panel. (Left or right, or left and right). Stacking at acute angle. All panels brought into position with rear track roller. Stacking in a box or niche, behind end panel. Sliding panels only, around 135 offset (left or right, or left and right). DORMA 5

SUPPORT AND GUIDE ELEMENTS PANELS PARALLEL TO TRAVEL DIRECTION Stacking track at 5 angle for small number of panels (up to 6) (left or right, or left and right). Stacking track offset in niche with folding panel as wall connection (left or right, or left and right). X Stacking track 135 (left or right, or left and right). Detail X Sliding panel with final folding panel in closed wall. Max. system height 3 m Sliding panel with final folding panel ready for sliding into stacking track. Max. system height 3 m Parallel stacking track for large number of panels (left or right, or left and right). Parking behind fixed panels (left or right, or left and right). Fixed panels Sliding panel 1 Stacking track 90 behind column with pivoting end panel as possible access leaf (left or right, or left and right). Stacking track beyond offset pivoting end panel (left or right, or left and right). Closed system 6 DORMA

EXAMPLE STACKING ARRANGEMENTS SPECIAL STACKING ARRANGEMENTS Stacking at the wall in closed compartment behind pivoting end panel Stacking at the wall in closed compartment without pivoting end panel Stacking in front of 90 wall with 90 angle section without closing pivoting end panel Stacking panels of varying width Closed wall Stacking without stacking track with 4 panels (2 pivoting end panels / 2 sliding panels) DORMA 7

SUPPORT AND GUIDE ELEMENTS STACKING ARRANGEMENT CALCULATIONS Straight track rail with stacking position transverse to travel direction T1 T2 = T1 36 100 100 150 a b b b 65 65 a b = depending on pull handle depth or 75 mm where profile cylinder provided at front-mounted slide bolt = 65 mm for HSW-G 80 mm for HSW-R 90 mm for HSW-ISO Width of stacking track B1 = Panel width 120 mm (0.087 x T1) 100 92 B2 = B1 192 * HSW-GP cannot be provided with a 95 branch 95 * 92 T3 = T4 92 T4 = T1 Straight track rail with stacking track parallel to direction of travel (135 ) a b = depending on pull handle depth = 65 mm for HSW-G 80 mm for HSW-R and HSW-GP 90 mm for HSW-ISO B1 100 100 B2 = B1 41 41 B1 = Panel width 130 mm T1 = T3 x 1.414 mm T3 b b b b a 100 135 T1 T2 = T1 41 8 DORMA

5 HSW / FSW STACKING ARRANGEMENT CALCULATIONS Straight track rail with stacking position parallel to travel direction (90 ) with up to approx. 10 panels 100 100 B1 36 B2 = B1 128 92 95 * a b = depending on pull handle depth or 75 mm where profile cylinder provided at front-mounted slide bolt = 65 mm for HSW-G 80 mm for HSW-R 90 mm for HSW-ISO 80 T2 = T1 100 100 b b b a 130 b T1 * HSW-GP cannot be provided with a 95 branch B1 = Panel width 130 mm ([T1 80] x 0.087) Straight track rail with stacking position parallel to travel direction (90 ) with more than 10 panels 100 100 B1 130 36 B2 = B1 136 100 90 b b b b a T2 = T1 100 100 T1 a b = depending on pull handle depth or 75 mm where profile cylinder provided at front-mounted slide bolt = 65 mm for HSW-G 80 mm for HSW-R and HSW-GP 90 mm for HSW-ISO B1 = Panel width 130 mm 80 b b DORMA 9

10 DORMA HSW SUPPORT AND GUIDE ELEMENTS Track Rails 12-13 Substructure 14 19

DORMA 11

SUPPORT AND GUIDE ELEMENTS TRACK RAILS AND MODULES Flexible and stable Horizontal sliding walls can be constructed in a wide range of different configurations to suit the site of installation, prevailing structural conditions and the planning concept. With DORMA HSW systems, a variety of designs can be implemented with ease. Straight, segmented and curved track rails can be combined to produce virtually any serpentine shape required. The track rails in the form of hollow sections combine all the virtues of light weight, stability and torsional stiffness. And when combined with the HSW substructure, installation becomes even easier. Flexibility and stability mean that even unusual system configurations can be implemented without problem to give maximum functional reliability. Straight track rail 90 T-piece 72 75 Stacking track rail 50 150 150 l 9 Track rail at closed wall position 50 300 36 200 40 75 l 9 40 60 60 40 400 Straight track rail For a straight-line system configuration, a drill hole interval of 300 mm in the track rail is sufficient, while the stacking area requires an interval of 150 mm. Where the track assumes an angle of 161 179, the track rail is mitred, while at angles between 90 and 160, a segment is incorporated. The standard modules available are indicated in the adjacent illustrations. 135 T-piece Left or right 36 80 30 30 400 36 l 9 90 L-piece 200 60 40 90 l 9 36 60 200 40 Modul 07/09 for 90 /95 angle Modul 06 for 45 angle 90 angle left/right 22.5 36 136 85 /90 36 136 45 136 90 136 12 DORMA

TRACK RAILS Segmented track rail With the segmented track rail, it is possible to implement the DORMA HSW as a polygonal partition or frontage. In so doing, it is essential to note the following requirements:. the panel width and segment chord length must be properly coordinated;. segment panels are provided at the bottom with locks or face-mounted floor bolts and the end cap are equipped with additional buffers for collision protection;. it is important to ensure that the opening sweep of single action and double action panels does not give rise to collisions. Curved track rail A curved track rail is also available where a curved DORMA HSW system configuration is required. The most important technical prerequisites for this are as follows: 1 2 50 300300 300 200 300 3 l 9 1 Rmin of the neutral fibre = 3500 mm 72 Curved track rail, bolted double shell construction Countersunk screw DIN 7991 M6x10. A2 75. only non-pivoting sliding panels may be installed in the curved track rail section;. the track rail must be straight in the parking or stacking area;. no top locking element can be installed;. each panel is provided with two face-mounted floor bolts;. a 100 mm straight track section (1) is necessary as the transition from the curved track rail to the straight stacking track rail;. blends from the curved configuration to a straight line can be implemented using standard modules (2);. the smallest curve radius is 3,500 mm (smaller radii on application) (3);. the feasibility of elliptic system configurations must be considered on a case-bycase basis for this, drawings will be necessary;. the start and end points of the curve are always provided with a 90 saw cut (radial saw cut). DORMA 13

SUPPORT AND GUIDE ELEMENTS SUBSTRUCTURE - THE SYSTEM Solutions Installing a horizontal sliding wall system invariably requires a certain set of structural conditions to be established. The system will need to be precisely aligned vertically usually sub-sequent to installation as well as being exactly configured and securely located. Because DORMA HSW systems do not use floor-level supports and floor tracks, the system requirements and all their technical properties must be taken into account when designing the substructure and its incorporation within the ceiling. This often very costly planning process is normally undertaken by the fabricator as the installation company, and alongside the calculations there are many individual structural and installation procedures involved. The new DORMA substructure system is of modular construction and is designed to significantly reduce on-site installation cost and time. This concept also offers the particular flexibility required to overcome structural constraints, such as the presence of air conditioning shafts or pre-existing electrical systems in the ceiling. Milled U recess M10 threaded rod Fixing plate Pivoting angle bracket Lateral bolting channel Standard square section tubes Pivot fixing Substructure profile Upper bolting channel Centre channel System design The DORMA substructure consists primarily of the following components: substructure profile with modules for branching to the stacking area, threaded rods for suspension of the profile(s), and standard square section tubes with appropriate fixings and ceiling brackets for bracing and stiffening the construction. 14 DORMA

SUBSTRUCTURE The forces (shown by arrows) that occur during opening and closing of the sliding wall system must be absorbed by appropriately located bracing elements. Safety and flexibility The DORMA substructure has been developed on the basis of extensive practical experience of the requirements involved in this kind of system. Consequently, the profile incorporates features that greatly facilitate installation and ensure that pre-existing structural factors can be accommodated with maximum flexibility. Various bolting channels run the whole length of the profile, allowing bolts to be inserted easily at any location within the system configuration. So there is no need for pre-drilling and thread cutting in order to mount the track rails onto the substructure. Bolted connections can be made directly through the lower bolting channel. The problem of removing drillings and filings from the track rails is thus also a thing of the past. Bolting channels on both sides of the profile can be used e.g. for fixing the brackets needed for attaching the ceiling retention elements. In addition, centering grooves on all main profile surfaces facilitate overhead drilling, e.g. for accessory attachment. Welding brackets designed for bolting onto the profile provide another option, allowing the DORMA system to be utilised for additional customer-specific applications. The substructure profile is suspended from threaded rods. These are first placed in the U-recesses using fixing plates that lock into the upper bolting channel. Each pair of threaded rods is regarded as constituting one suspension point. Here again the system remains exceptionally flexible: the staggered U-recesses positioned at intervals of 100 mm enhance the ability of the system to accommodate structural constraints. Depending on the weight of the system and the permitted deflection, it is possible to span a distance of up to 2,100 mm between two suspension points. The centre channel can be fitted with two flat aluminium bars to provide additional rigidity in the area of butt joints between profiles In this case it is possible to dispense with the dual suspension arrangement with one suspension point either side of the joint which is otherwise necessary. So existing building installations of all types can be effectively bypassed. Once the substructure has been installed, the HSW system is vertically aligned and fixed directly via the threaded rods. Subsequent adjustments, e.g. after the building has settled into its foundations, can also be carried out by the same means. The standard square section tubes offer extra safety, especially where the sliding panels deviate from a straight line. Panel sway must be effectively countered by the structural design adopted at such locations. Diagonal struts that counteract the pressure load stabilise the system in the area of the stacked panels. The telescopic square section tubes are connected as additional bracing elements (struts) to the substructure by a pivot fixing. The struts are bolted to the ceiling using the appropriate angle brackets. The modular design of the DORMA substructure is precisely matched to the modules of the DORMA HSW track rail. The structural elements can be mixed and matched as desired with the result that a small number of component types is sufficient to create a complex, flexible system that conforms fully to all safety requirements. A drawing of the required substructure can be requested from DORMA to supplement the HSW system drawing always supplied with the quotation. DORMA 15

SUPPORT AND GUIDE ELEMENTS PLANNING DETAILS Calculating the suspension intervals Max. 2 mm deflection between two suspension points With a maximum load (panel weight) of 150 kg/m and a permitted deflection of the substructure with track rail of 2 mm, the interval between two suspension points must be no greater than 1450 mm. The table below shows other values for different loads. 1450 mm In order to prevent system sway, every second suspension point must be reinforced by a strut. The substructure profile ends (travel path and stacking area) should ideally be directly connected to the masonry or to existing structural members. Illustrative example of load values Table for the calculation of the max. distance dimension Front AM Parking area F HSW-G characteristic values Formula for calculating the: Glazing height = system height 309 mm = panel height 193 mm Glazing weight Glass 10 mm = 25.00 kg/m 2 Glass 12 mm = 30.00 kg/m 2 Door rail weight Aluminium = 12.00 kg/m Brass = 14.50 kg/m Stainl. steel = 13.25 kg/m Distance dimension max. depending on carrying function F AM 60 kg/m 2,050 mm 75 kg/m 1,900 mm 90 kg/m 1,750 mm 105 kg/m 1,750 mm 120 kg/m 1,600 mm 135 kg/m 1,600 mm 150 kg/m 1,450 mm 160 kg/m 1,450 mm F = Force AM = Distance dimension Force example: The distance dimension of 108,98 kg/m = 1,710 mm (can be linearly interpolated) Example system HSW-G system in stainless steel System height 3,500 mm Glazing thickness 12 mm Calculation Load = glazing weight x glazing height + door track weight = 30 kg/m2 2 x (3,500 mm 309 mm) + 13.25 kg/m = 30 kg/m 2 x 3,191 mm + 13.25 kg/m = 108.98 kg/m 16 DORMA

SUBSTRUCTURE STACKING AREA DESIGN View from below The construction of the stacking area, assembled from substructure and track rail modules, provides a good illustration of how this well-designed system can be utilised. The individual components are coordinated to ensure safe integration. Joints in the substructure are offset to those in the track rails so that individual joints coincide with continuous material in all cases. Provided that the track rails are adequately bolted to the substructure, gaps of up to 40 cm measured from one suspension point to the next are permitted in the substructure. View from below Substructure Track rail Detachable section 90 branch module 95 branch module Strut View from above Joints reinforced by central steel bar only require one local suspension point. 1 suspension point = 2 threaded rods L-piece for 95 branch Strut Joint area reinforced using flat steel bars inserted in the centre channel 90 T-piece Suspension points either side of joints not reinforced by central steel bar DORMA 17

SUPPORT AND GUIDE ELEMENTS VARIANTS OF CONNECTION / DETAILS UK-Profile Profile connection with connection lug Art. No. 815.442.001.40 Wall connection with angeled connection lugs. Bending of connection lug on site according to need Art. No. 815.442.001.40 30.5 30.5 30 50 Direct connection to ceiling Welding connection to steel girder Connection opportunities to existing bearing structure like ceilings, balks, steel girder by dint of adapter plate Art. No. 815.435.001.40 Flexible connection to ceiling Connection to steel construction 18 DORMA

SUBSTRUCTURE COMPONENT PARTS, ACCESSORIES Component parts D 1 E 1 Pivoting angle bracket Art. No. 815.437.001.40 2 Fixing plate Art. No. 815.434.001.40 3 Pivot fixing Art. No. 815.436.001.40 4 Adapter plate Art. No. 815.435.001.40 5 Basic substructure profile, stock length 6000 mm Art. No. 815.658.000.99 Fixed length Art. No. 815.659.000.99 A F DIN and standard parts by others or on request CSN = Company standard no. B 2 I C B 5 K 3 J 4 H G Adapter plate for neutral connection G L A Threaded rod M10 x 1,000 CSN 800.01.470.3.30 B Hex nut DIN 439-2 M10 CSN 800.03.001.3.30 C Washer ISO 7089-10 CSN 800.04.009.3.30 D Hex nut DIN 934-M6 CSN 800.03.005.3.30 E Hex socket screw DIN 933-M6x35 CSN 800.01.337.3.30 F Telescopic strut top section, square section tube, galvanised steel 20x20x2 CSN 800.16.025.4.32 G Drilling screw DIN 7504 ST4 8x16 CSN 800.01.286.3.30 H Telescopic strut bottom section, square section tube, galvanised steel 25x25x2 CSN 800.16.026.4.32 I Hex nut DIN 934-M6 CSN 800.03.005.3.30 J Hex socket screw DIN 933-M6x40 CSN 800.01.319.3.30 K Self-tapping screw ISO 7049-St4.8 x 13-C-H CSN 800.01.493.3.30 L Cylinder head screw for fixing track rail to substructure profile DIN 912-M8x25 CSN 800.01.018.3.30 49 Stock length 6000 mm 200 100 100 100 75 0.5 A 72 17 +0.2 11 +0.2 DORMA 19

20 DORMA HSW / FSW PANEL SYSTEM HSW-G 22 34

DORMA 21

PANEL SYSTEM PANEL TYPES In the case of the fully glazed HSW-G / HSW-MR systems, the panels create a continuous, transparent surface without any lateral framing. For a more sophisticated or intricate appearance, single-point fixings (HSW-GP) are also available. HSW-G / HSW-MR / FSW-G / FSW-C/C plus Fully glazed with door rails HSW-GP Fully glazed with single-point fixings This folding system with top and bottom glazing rails coordinates perfectly with the HSW-G variant. The FSW-G operates without a separate stacking area, and instead folds together within the main frontage or partition zone. 22 DORMA

HSW-G HSW-R Fully framed HSW-ISO Fully framed with double glazing The all-round framing provided on the individual panels of an HSW-R system not only offers high stability but also an excellent barrier to keep out external influences. The panels can be constructed with laminated or toughened safety glass as required. DORMA 23

PANEL SYSTEM PANEL TYPES AND FUNCTIONS Horizontal sliding walls Fully glazed with glazing rails (100 mm) top and bottom Within an HSW-G system, the individual panels can be designed to perform certain special functions. These range from simple sliding panels to integrated doors with a variety of door closers, or special panels for unusual installation situations. And each system can be assembled to suit individual requirements. The standard glass thickness is 10 or 12 mm. Further glass thicknesses on request. Max. panel sizes and weights Single action / double action end panel Non-sliding. Single action panel with floor pivot and TS 92 / TS 73 door closer. Double action panel with floor pivot or BTS floor spring. Sliding panel Fixed when frontage closed. Single action sliding panel Single action sliding panel with TS 92 cam-action door closer, operational when frontage closed. Alternatively with ITS 96 1). Double action sliding panel * With RTS transom door closer, operational when frontage closed. Alternatively with ITS 96 2). Double action sliding panel * With RTS transom door closer, operational when frontage closed. Alternatively with ITS 96 2). Max. system height 4,000 mm 4,000 mm 3,600 mm 3,600 mm 3,600 mm Max. panel width 1,250 mm 1,250 mm 1,250 mm 1) 1,100 mm 1,250 mm 2) 1,100 mm 1,250 mm 2) 1,100 mm Max. panel weight 150 kg 150 kg 100 kg** 100 kg** 100 kg** The individual panels can also be of differing widths. The largest width should not exceed max. 115% of the smallest width. * For these panel types please consider our notes on portal systems on page 101. ** Note: The maximum permissible weight relates to the complete door assembly, including handles. 24 DORMA

HSW-G SYSTEM DESIGN Bottom door rail designs All depicted combinations are also available as mirror arrangements End-mounted pin bolt at wall End-mounted pin bolt at wall End-mounted pin bolt at wall Recess for end-mounted slide bolt End-mounted slide bolt Face-mounted slide bolt Deadlock Face-mounted slide bolt 2,5 75 75 100 35 33 ±5 72 1 2 3 4 5 6 Irrespective of the function of the individual panels, an HSW-G system comprises the following basic components: 1 Installation-efficient DORMA substructure to accommodate track rail mounting requirements (optional) 2 Track rail for bolting to the substructure. 3 Carrier 4 Suspension assembly and 5 bearing profile for safe and easy sliding of the panels. 6 Top door rail and 7 bottom door rail, both comprising base profiles with clip-on face and side covers. 8 Toughened safety glass (by others). Toughened laminated safety glass on request. Recess for end-mounted slide bolt End-mounted slide bolt 25 8 Recess for end-mounted slide bolt Deadlock 32 Deadlock End-mounted slide bolt 10 8 100 7 7 20 Face-mounted slide bolt End-mounted slide bolt Face-mounted slide bolt Face-mounted slide bolt Floor surface Face-mounted slide bolt Deadlock DORMA 25

PANEL SYSTEM FIXED PANEL Double action or single action end panel with floor pivot Non-moving and always equipped with a bottom deadbolt with the option of a top bolt or sideaction deadlock. Can be designed as a double action or single action leaf. Double action end panel Assembly types:. Floor pivot with round spindle. BTS 84 for panels up to 100 kg, with optional holdopen at 90 door opening angle. BTS 80 for panels up to 150 kg with adjustable hold-open device Glazing height = Total height 308 mm 25 20 100 100 35 33 ±5 75 7 2,5 2,5 4 63 4 63 End cover 36,5 27 Pivot bearing door rail insert (for BTS as well) Single action end panel with stop-type covers top and bottom. Assembly types:. Floor pivot with round spindle. As above, but with DORMA TS 73 or TS 92 overhead door closer. BTS 84 for panels up to 100 kg, with optional holdopen at 90 door opening angle. BTS 80 for panels up to 150 kg with adjustable holdopen device Double action end panel with floor spring 4 45 4 19 63 65 36 bottom strap in forged steel Mounting dimensions BTS 84 BTS 80 a 108 78 b 40 60 b a d c c 306 341 d 51 58 51 57 26 DORMA

HSW-G Single action end panel with TS 73 overhead door closer and additional locking device 222 45 63 193,5 205 160 140 Single action end panel with TS 92 overhead door closer and additional locking device 375 23 17 max. 14 63 145,5 199 140 min. panel width 870 mm Additional locking device 7 6 Data and features TS 73 V TS 92 Closing strength/size EN 2 4 EN 2 4 Closing strength, variable via adjusting screw and arm hinge via adjusting screw and arm hinge Closing speed adjustment via valve via valve Non-handed x x Latching speed adjustment via arm via arm Cushioned stay limit adjustment 75 180 80 120 Hold-open adjustment 75 160 75 150 Weight 1.8 kg 1.9 kg Length 233 mm 281 mm Overall depth 42.50 mm 47 mm Height 60 mm 65 mm DORMA 27

PANEL SYSTEM SLIDING PANEL Track roller 100 25 2,5 35 33 ±5 75 65 65 End cover Stationary when the frontage or partition is closed. Sliding panel The sliding panels are the moving elements. Once in their closed position, they are locked down. The components available for this are provided in the bottom door rail in the form of face-mounted slide bolts, end-mounted slide bolts, end pin bolts or deadlocks. Glazing height = Total height 308 mm 32 20 100 7 Sliding panel 4 Sliding panel End-mounted slide bolt Turn grub screw to adjust locking pin Eccentric bushing Bottom door rail Panel width 250 250 Base profile with integral functional element (here: face-mounted slide bolt) Base profile with functional element (here: deadlock) 28 DORMA

PANEL TYPES HSW-G SINGLE ACTION SLIDING PANEL 75 Track roller 35 33 ±5 100 4 TS 92 Sliding panel Pivot bearing Single action sliding panel Swing panel with TS 92 camaction door closer for operation as a single action door when the frontage is closed. With DORMA TS 92 cam-action door closer This panel type is installed where doors only need to be opened in one direction. The pivoting sliding panels can be fitted open inwardly or outwardly. In both cases, the cam-action door closer is fixed to the inside face. Glazing height = Total height 308 mm 25 20 100 7 4 65 Face-mounted slide bolt Eccentric bushing Standard assembly top: Pivot bearing, TS 92 with slide channel, one locking device bottom: Face-mounted slide bolt as pivot (released for sliding function) and lock Locking device 8 129 73 Optional equipment top: Second locking device (for reshuffle bypass) bottom: Optional second facemounted slide bolt instead of deadlock 13.5 15 4 M6 l 7 l 10 max. 2.5 60 110 Top pivot DORMA 29

PANEL SYSTEM DOUBLE ACTION SLIDING PANEL Max. Sliding panel weight 100 kg Track roller Pivoting panel with RTS transom door closer for operation as a double action door when the frontage is closed. With integral DORMA RTS transom door closer Double action sliding panels with DORMA RTS transom door closers (patented design) are characterised by their exceptional ease of installation and operation; an excellent alternative to the solution with the BTS floor spring because the RTS does not require a large recess in the floor. These panels are generally equipped with a bottom deadlock and top locking device plus a bottom facemounted slide bolt operating as the pivot bearing (released for the sliding function). The standard solution takes the form of the RTS 85 without hold-open, or as a special option, with a 90 hold-open. For these panel types please consider our notes on portal systems on page 101. 3 Glazing height = Total height 312 mm 7 20 20 Locking device RTS 85 100 l 7 M6 56 46 32 33 ±5 75 58 8 Sliding panel 4 65 129 RTS 85 RTS insert Double action sliding panel Face-mounted slide bolt Eccentric bushing 73 l 7 max. 2.5 60 14,5 3 110 Top pivot 30 DORMA

HSW-G FIXED PANEL Position 90 and 180 opening angle at wall, position 180 opening angle at fixed panel Top centre upper part 35 33 ±5 75 45 2,5 21 Top centre lower part 100 End cover 4 180 opening angle Offset pivoting end panel at fixed panel Max. panel weight 100 kg Offset hung end panel Single action panel, non-sliding, operates independently of the rest of the system. The single action door with offset pivoting arm assembly can be swung around 180, so leaving the entire operating zone free. A bottom deadlock secures the closed leaf. Bottom door arm 45 100 7 2 4 Pivoting end panel views as seen from below 75 Fixed panel fixing arrangement 65 2,5 35 33 ±5 Glazing height = Total height 308 mm 20 25 100 Fixed side panel Non-moving side panel, independent of the rest of the system. The fixed side panel is of the same basic design as the sliding panels. And if required, the fixings can be replaced by a carrier system to convert such a panel into a sliding panel. 100 7 Sliding panel 4 Fixed panel End cover End-mounted slide bolt with fixed pin DORMA 31

PANEL SYSTEM FOLDING SLIDING PANEL Magnetic door holder Panel hinge Roller carrier Magnetic door holder End-mounted slide bolt and panel hinge 30 25 100 2.5 35 33±5 75 4 20 65 Magnetic door holders top and bottom Hinged, with lock and slide bolt at the bottom, latching bolts top and bottom for fixing the final folding panel to the slide panel. FSW-C 42 FSW-C plus 72 30 Max. panel sizes and weights Max. panel width 2 x 1,000 mm Max. system height 3,000 mm Max. panel weight 2 x 70 kg End mounted slide bolt Panel hinge 28 15 32 DORMA

PANEL TYPES HSW-G SLIDING PANEL WITH ITS Max. panel weight 100 kg 75 Rollercarrier Sliding track 4 25 100 20 35 33 ±5 Single action sliding panel with integral door closer ITS 96 Gr. 2 4 This panel variant is used where the door element is required to only open in one direction. Single action sliding panels can be either inward or outward opening. Glazing height = Total height 308 mm 37 32 100 7 Single action sliding panel 4 65 Pivot point Front mounted slide bolt Eccentric bushing Standard equipment pivot at the top, ITS 96 with slide channel, 1 locking device at the bottom in the form of a face-mounted slide bolt (released in sliding mode) and deadbolt lock. M6 8 129 75 Optional equipment top 2 nd locking device (to facilitate disengaging); bottom: 2 nd facemounted slide bolt instead of deadbolt lock. l 7 max. 2.5 4 15 l 7 15 Single action sliding panel inward opening Stop Sliding panel 60 110 Data and features: ITS 96 Gr. 2 4 Closing strength / size EN 2 4 Max. opening angle ca. 120 Max. panel width 1,100 mm Hold-open variable yes Max. panel height 100 kg Weight 1.3 kg Closing strenght continuously variable Adjusting screw Length 277 mm Closing speed continuously variable Valve Overall depth 32 mm Same design for DIN-L and DIN-R yes Height 42 mm Latching speed continuously variable yes Door closer tested according to EN 1154 yes Cushioned stay limit mechanically variable yes DORMA 33

PANEL SYSTEM DOUBLE ACTION SLIDING PANEL WITH INTEGRAL DOOR CLOSER Roller carrier Sliding track Double action sliding panel with integral DORMA door closer Double action sliding panels with DORMA ITS 96 Gr. 2 4 offer exceptional ease of installation and operation, making them a good alternative to the variant with the BTS floors spring particularly as the ITS 96 does not need a large recess in the floor. Being virtually invisible, its presence has no effect on the overall appearance of the partition. These panels come equipped as standard with a bottom deadbolt lock and a locking device at the tope, together with a face-mounted slide bolt as the bottom pivot point (released in the sliding mode). In its standard form, ITS 96 is provided with a 90 hold-open. If you care considering this panel type, please note our advisories relating to portal systems on page 101. 75 M6 100 4 35 33 ±5 Glazing height = Total height 308 mm l 7 l 7 25 20 37 32 100 7 max. 2.5 4 Double action sliding panel 4 15 8 65 15 Pivot point front mounted slide bolt Eccentric bushing 129 60 110 75 Data and features: ITS 96 Gr. 2 4 Closing strength / size EN 2 4 Max. opening angle ca. 120 Max. panel width 1,100 mm Hold-open variable yes Max. panel height 100 kg Weight 1.3 kg Closing strenght continuously variable Adjusting screw Length 277 mm Closing speed continuously variable Valve Overall depth 32 mm Same design for DIN-L and DIN-R yes Height 42 mm Latching speed continuously variable yes Door closer tested according to EN 1154 yes Cushioned stay limit mechanically variable yes 34 DORMA

HSW-G DORMA 35

36 DORMA HSW / FSW PANEL SYSTEMS HSW-MR 38-42

DORMA 37

PANEL SYSTEM TYPES AND FUNCTIONS Horizontal sliding walls Fully glazed with glazing rails (75 mm high) top and bottom. Designed to meet the minimum essential requirements of a shopfront, the HSW-MR constitutes a cost-efficient alternative to the classic HSW-G. The HSW-MR assemblies are available for 10 or 12 mm glass thickness. Double action / single action end panel Non-sliding. Doubel action end panel with floor bearing and top pivot. Optional with floor spring BTS 80 / 84. Or as single action end panel with stop and BTS 80 / 84 or TS 92 / TS 73. Sliding panel Fixed when frontage closed. Sliding panel Fixed when frontage closed. Fixed panel Non-sliding. Fixed side panel with retaining pins at the top and door rail with bottom spacer profile at the bottom. Max. panel sizes and weights Max. system height 3,000 mm 3,000 mm 3,000 mm 3,000 mm Max. panel width 1,250 mm 1,250 mm 1,250 mm 1,250 mm Max. panel weight 100 kg 100 kg 100 kg 100 kg 38 DORMA

HSW-MR SYSTEM DESIGN Bottom door rail designs All depicted combinations are also available as mirror arrangements 72 Irrespective of the function of the individual panels, an HSW-MR system comprises the following basic components: End-mounted pin bolt at wall End-mounted pin bolt at wall Recess for end-mounted slide bolt Recess for end-mounted slide bolt Deadlock End-mounted slide bolt Deadlock End-mounted slide bolt Deadlock End-mounted slide bolt 1 2 3 4 5 6 8 8 7 36 19 19 7 75 75 35 33 ±5 75 75 3 1 Installation-efficient DORMA substructure to accommodate track rail mounting requirements (optional). 2 Track rail for bolting to the substructure. 3 Carrier 4 Suspension assembly and 5 bearing profile for safe and easy sliding of the panels. 6 Top door rail and 7 bottom door rail, both comprising base profiles with velcro technique and side covers. 8 Toughened safety glass or toughened laminated safety glass (by others) 10 / 12 mm. DORMA 39

19 19 75 75 75 7 HSW / FSW PANEL SYSTEM FIXED PANEL 65 130 Double action or single action end panel with floor pivot Non-moving and always equipped with a bottom deadbolt with the option of a top bolt or sideaction deadlock. Can be designed as a double action or single action leaf. Total height Glazing height = Total height 265 mm 63 94 Double action end panel Assembly types:. Floor pivot with round spindle. BTS 80 / 84 for panels up to 100 kg, with optional holdopen at 90 door opening angle 75 7 Single action end panel with stop top or stop-type covers top and bottom. Assembly types:. Floor pivot with round spindle. BTS 80 / 84 for panels up to 100 kg, with optional holdopen at 90 door opening angle Double action end panel with floor spring 27 36 36,5 65 19 45 The choice of door closer will depend on the installation situation in each case. 4 63 Mounting dimensions BTS 84 BTS 80 a 108 78 b 40 60 c 306 341 b a d c d 51 58 51 57 40 DORMA

HSW-MR SLIDING PANEL 19 75 75 4 67 Sliding panel Stationary when the frontage or partition is closed. The sliding panels are the moving elements. Once in their closed position, they are locked down. The components available for this are provided in the bottom door rail in the form of end-mounted slide bolts, end pin bolts or deadlocks. Total height 19 Glazing height = Total height 265 mm 7 Bottom door rail Panel width 250 250 Base profile with integral functional element (here: end-mounted slide bolt) Base profile with functional element (here: deadlock) DORMA 41

PANEL SYSTEM FIXED PANEL 75 3 36 7 75 19 35 33 ±5 75 67 67 19 4 Fixed side panel Non-moving side panel, independent of the rest of the system. The fixed side panel is of the same basic design as the sliding panels. And if required, the fixings can be replaced by a carrier system to convert such a panel into a sliding panel. Glazing height = Total height 265 mm 42 DORMA

HSW-MR DORMA 43

44 DORMA HSW / FSW PANEL SYSTEMS HSW-GP 46-49

DORMA 45

PANEL SYSTEM HSW-GP PANELS AND FUNCTIONS Fully glazed sliding walls with point-fixed track roller carriers engaging in standard track rail. The characteristic features of HSW-GP systems are the singlepoint fixings of the glass panels in combination with a conventional track rail profile. The design, featuring a high-grade stainless steel finish and the distinctive flush-mounted or clamping disc attachments, coordinates perfectly with contemporary architecture. Even curved glazing can be securely held by this system. And this can also be combined with curved track rail profiles to produce unique configurations. The standard glass thickness is 10/12 mm. Further glass thicknesses on request. Max. panel sizes and weights Double / single action end panel Non-sliding. With full-length pivot rod and offset pivot. Single action panel with floor pivot, round spindle and stop. Double action panel with floor pivot or BTS floor spring. Sliding panel Fixed when frontage closed. Double / single action end panel Non-sliding. With centre pivot top and bottom. Single action panel with floor pivot, round spindle and stop. Double action panel with floor pivot. Fixed panel Non-sliding. Fixed side panel with retaining pins at the top and fixed panel straps at the bottom. Max. system height 3,000 mm 3,000 mm 3,000 mm 3,000 mm Max. panel width 1,200 mm 1,200 mm 1,200 mm 1,200 mm Max. panel weight 100 kg 100 kg 100 kg 100 kg The position of the track is not adjustable. The width of all panels must be uniform. 46 DORMA

HSW-GP SYSTEM DESIGN Sliding panel with bottom end-mounted pin Sliding panel with bottom face-mounted slide bolt The HSW-GP system consists of the following basic components: 1 2 3 4 72 75 75 29 44 119 72 75 29 75 44 119 1 installation-efficient DORMA substructure to accommodate track rail mounting requirements (optional). 2 track rail for bolting to the substructure. 3 roller, 4 suspension assembly, 5 strap with single-point fixings, 6 toughened safety glass or toughened laminated safety glass (by others), 7 bottom strap with end-mounted pin, 8 bottom strap with face-mounted slide bolt. Inside 11 Inside 50 4 11 4 50 5 6 7 64 55 55 Glazing height = Total height 126 mm Total height 15,5 8,5 39 8 64 55 55 Glazing height = Total height 126 mm Total height Floor surface 7 7 DORMA 47

PANEL SYSTEM TYPES AND GLASS DRILLING REQUIREMENTS Double / single action end panel with pivot rod Glass drilling pattern Glazing width 7 Pivot pin Pivot rod, short type with singlepoint fixings Pull handle with single-point fixings/ Back-to-back pull handles Pivot rod connecting tube Pivot rod, short type with singlepoint fixings Deadlock Bottom bearing bush 73 150 71 Length of connecting tube = Glazing height 535 mm 8 Glass bore centres for pull handle/back-to-back pull handles 1560 ± 0,3 1040 ± 0,3 520 ± 0,3 min. 65 mm 65 65 65 Countersunk bores Countersunk bores l 55 for deadlock 150 150 71 113 Glazing height = Total height 126 mm Double / single action end panel Glass drilling pattern Glazing width Strap with singlepoint fixings 50 55 Glass bore centres for pull handle/back-to-back pull handles 41 50 55 Countersunk bores Pull handle/back-toback pull handles Deadlock Pivot strap with floor pivot 55 64 8 49 1560 ± 0,3 1040 ± 0,3 520 ± 0,3 min. 65 mm 65 Countersunk bores 65 l 55 for deadlock 41 64 Visible corner notch 55 Glazing height = Total height 126 mm 48 DORMA

HSW-GP Sliding panel Fixed panel Glass drilling pattern 50 50 41 Glazing width 41 50 Straps with single-point fixings Straps with single-point fixings 55 55 Countersunk bores 55 Bottom strap with face-mounted slide bolt Fixed panel strap 41 41 Glazing height = Total height 126 mm Bottom strap Fixed panel strap 55 55 64 Countersunk bores 64 55 8 64 8 41 Visible corner notches Glass bores and notches Countersunk bores for single-point fixings for the pull handles and straps l 26 10/12 l 32+0,2 90 Bores for clamping disc single-point fixings l 26 Bores for pull handle pairs l 22 Bores for locks l 55 Visible corner notches, bottom 67 15 15 67 10/12 10/12 R10 R10 3-0,2 10/12 Special stop Pivot rods (short type) with singlepoint fixings and connecting tube Pull handle with single-point fixings ± 15 62 ± 15 Bottom pivot for pivot rods Back-to-back pull handles DORMA 49

PANEL SYSTEMS FSW-G 52-55 50 DORMA

DORMA 51

PANEL SYSTEM TYPES AND FUNCTIONS FSW folding sliding walls as fully glazed partitions and frontages, with door rails top and bottom, track roller position at the end of every second panel. Folding sliding walls are ideal for a straight-line system configuration. In an FSW-G partition, there are either 2 or 4 interlinked panels (1 base panel and 1 or 3 folding panels). With double assemblies moving counter to each other (bi-parting), therefore, it is possible to create frontages comprising up to 8 FSW panels. As the panels of an FSW system are visually compatible with those of the HSW-G line and both systems use the same track construction, the two can be ideally combined as a single shopfront or transparent partition, with the FSW system mating at its free end with a free HSW single-action or double-action access panel (types 4 + 5). For assembly types see pages 60 63. Example: assembly with 2 x 2 panels (type 1c) moving counter to each other 1 Track rail 2 Folding panel 3 Folding hinge 4 Roller 5 FSW base panel 6 Top locking device 7 Bottom locking device 5 1 4 7 2 6 2 6 5 3 Base panel with top pivot and bottom floor pivot. Folding panel with carrier and locking device top Folding panel with carrier and locking device top Folding panel with carrier and locking device top Max. panel sizes and weights and bottom. and bottom. and bottom. Max. system height 3,000 mm 3,000 mm 3,000 mm 3,000 mm Max. panel width 1,000 mm 1,000 mm 1,000 mm 1,000 mm Max. panel weight 70 kg 70 kg 70 kg 70 kg The standard glass thickness is 10/12 mm. Further glass thicknesses on request. 52 DORMA

FSW-G SYSTEM DESIGN Base panel Folding panel 72 The FSW-G system consists of the following basic components: 1 2 3 6 7 8 8 12 9 11 10 4 5 13 32 10 25 20 7 100 100 35 33 ±5 75 75 2,5 Floor surface 1 installation-efficient DORMA substructure to accommodate track rail mounting requirements (optional). 2 track rail for bolting to the substructure. 3 top pivot, 4 roller, 5 top locking device, 6 suspension assembly and 7 carrier profile for safe and easy sliding of the panels. 8 folding hinge, 9 top door rail and 10 bottom door rail, both comprising base profiles with clip-on face and side covers. 11 toughened safety glass or toughened laminated safety glass (by others), 12 floor pivot, 13 face-mounted slide bolt. 3 8 8,5 Door rails cut to size 4,5 5 DORMA 53

PANEL SYSTEM ASSEMBLY TYPES Type 1 Type 1a 2 panels left, as drawn Type 1b 2 panels right, mirror arrangement Type 1c 4 panels (2 panels left and 2 panels right), bi-parting Type 2 Type 2a 4 panels left, as drawn Type 2b 4 panels right, mirror arrangement Type 2c 8 panels (4 panels left and 4 panels right), bi-parting min. 120 mm Type 3 Type 3a 6 panels as drawn (4 panels left and 2 panels right) Type 3b 6 panels mirror arrangement (2 panels left and 4 panels right) min. 120 mm 54 DORMA

FSW-G Type 4 Type 4a 2 panels left and 1 HSW double or single action end panel right (as drawn) Type 4b 2 panels right and 1 HSW double or single action end panel left (mirror arrangement) HSW Single or double action end panel Type 5 Type 5a 4 panels left and 1 double or single action end panel right (as drawn) Type 5b 4 panels right and 1 double or single action end panel left (mirror arrangement) min. 120 mm DORMA 55

56 DORMA HSW / FSW PANEL SYSTEMS FSW-C/C-Plus 58-63

DORMA 57

PANEL SYSTEM TYPES AND FUNCTIONS Folding sliding walls, fully glazed, with door rails top and bottom, track roller position in the panel centre. Large spans can be implemented with the FSW-C. Such a system consists of 1 base panel with up to 6 interlinked folding panels connected to it, plus one final folding panel as the access leaf (or alternatively 1 free singleaction or double-action door panel). Hence the number of panels can range from 3 to 8. Because the track rollers are located at the centre of the folding panels, the base panel has to be of half width (+ pivot offset of 63 mm). For reasons of symmetry, the final folding panel without guide roller is usually also of half-width design. The folding hinges have a small degree of pivot offset, which means the panels take up less room when stacked and also gives added stability to the system. The hinges exhibit a slight pivot offset. This ensures that the folded assembly is particularly compact while at the same time providing for good stability. The standard glass thickness is 10/12 mm. Further glass thicknesses on request. For assembly types see pages 60 63. Example: assembly type C2 (symmetrical with narrow folding panel) 1 Track rail 2 Final folding panel 3 Folding hinge 4 Locking device 5 Folding panel 6 Base panel 7 Top and bottom pivot bearing 8 Roller 1 2 3 3 4 8 4 8 5 5 4 4 3 3 6 7 Final folding panel access leaf with locking devices top and Folding panel with carrier, locking devices top and bottom. Folding panel with carrier and locking device bottom. Folding panel with carrier and locking device bottom. Base panel with top and bottom pivot bearing and locking device Max. panel sizes and weights bottom. bottom. Max. assembly height 3,000 mm 3,000 mm 3,000 mm 3,000 mm 3,000 mm Max. panel width 1,000 mm 1,000 mm 1,000 mm 1,000 mm 1/2 panel width + 63 mm Max. panel weight 70 kg 70 kg 70 kg 70 kg 58 DORMA

FSW-C SYSTEM DESIGN Folding panel with locking bolt 1 2 3 4 5 6 8 9 7 10 Floor surface 72 75 33 ±5 75 FSW-C 42 FSW-C plus 72 FSW-C 42 FSW-C plus 72 Latching bolts top and bottom 32 10 35 20 25 100 7 100 2,5 Latching bolts top and bottom 35 35 30 30 The FSW-C system consists of the following basic components: 1 installation-efficient DORMA substructure to accommodate track rail mounting requirements (optional), 2 track rail for bolting to the substructure, 3 roller, 4 suspension assembly and 5 carrier profile for safe and easy sliding of the panels, 6 top door rail and 7 bottom door rail, both comprising base profiles with clip-on face and side covers, 8 magnetic holder, 9 toughened safety glass or toughened laminated safety glass (by others), 10 bottom latching bolt. Bottom hinge End-mounted slide bolt, bottom Glass panels Facemounted slide bolt 20 28 15 DORMA 59

PANEL SYSTEM ASSEMBLY TYPES Type C1 1 HSW single action end panel as access leaf (here of narrow design for reasons of symmetry), 1 6 folding panels, 1 base panel (narrow) 1/2 FB 4 4 4 4 1/2 FB FB FB FB + 63 FB = Panel width Inside 74 mm between axes Inside between the door rails 42 mm Type C2 Inside 1 final folding panel (here of narrow design for reasons of symmetry), 1 6 folding panels, 1 base panel (narrow) 74 mm between axes Inside between the door rails 42 mm 60 DORMA

FSW-C Type C3 1 final folding panel as access leaf, 1 6 folding panels, 1 base panel (narrow) 1/2 FB 4 4 4 1/2 FB FB FB FB + 63 FB = Panel width Inside 74 mm between axes Inside between the door rails 42 mm Type C3, double (bi-parting) system 74 mm between axes Left: 1 base panel (narrow), 1 6 folding panels, 1 final folding panel as access leaf Right: 1 final folding panel as access leaf, 2 folding panels, 1 base panel (narrow) between the door rails 42 mm DORMA 61

PANEL SYSTEM PANEL TYPES, FUNCTIONS, ASSEMBLY TYPES Access with convenience the plus with the FSW-C. Based on the design of the FSW-C, the alternative FSW-C plus offers the added benefit that the connected final folding panel can also function as a fully fledged access leaf when the partition is closed with all the convenience of the DORMA TS 93 G door closer. In this case, the special bottom locking device and the top clamp-mounted stop stabilise the first folding panel, while the top angle stop ensures that the closed final folding panel is in the correct position. The folding hinges connecting the access leaf to the folding panel have a large pivot point offset in order to create room for the door closer and pull handles. All the other folding panels are equipped with a standard folding hinge and roller. Type Cp1 1 final folding panel as access leaf with TS 93 G door closer 1 6 folding panel 1 base panel (narrow) Inside 1/2 FB 4 4 FB FB 1/2 FB + 63 FB = Panel width Inside Dimensions between axes 104 between the door rails 72 between the door rails 42 Type Cp1 double (bi-parting) system 104 Dimensions between axes 72 between the door rails 42 mm between the door rails Inside Left: 1 base panel (narrow) 1 folding panel 1 6 final folding panel as access leaf with TS 93 G door closer Right: 1 final folding panel as access leaf with TS 93 G door closer 1 6 folding panel 1 base panel (narrow) Max. panel sizes and weights. Max. system height 3,000 mm. Max. width of final folding panel and folding panel 1,000 mm. Width of the base panel= half panel width + 63 mm. Max. weight of final folding panel and folding panel 70 kg. Number of panels 3 to 8 62 DORMA

FSW-C PLUS Type Cp2 1 final folding panel as access leaf with TS 93 G door closer 1 6 folding panel 1 base panel (narrow) Inside 1/2 FB between axes 104 mm between the door rails 72 mm 4 4 4 FB FB FB 1/2 FB FB = Panel width + 63 Inside between the door rails 42 mm 104 mm between axes 72 mm between the door rails 42 mm between the door rails Inside Type Cp2 double (bi-parting) system Left: 1 base panel (narrow) 2 folding panels 1 final folding panel as access leaf with TS 93 G door closer Right: 1 final folding panel as access leaf with TS 93 G door closer 1 6 folding panel 1 base panel (narrow) Data and features TS 93 Closing strength/size EN 2 5 EN 5 7 Closing force, variable via adjusting screw via adjusting screw Closing speed adjustment via valve via valve Non-handed yes yes Latching speed adjustment via valve via valve Cushioned stay limit adjustment 80 120 80 120 Hold-open adjustment 75 50 75 150 Weight 3.5 kg 5.2 kg Length 275 mm 285 mm Overall depth 53 mm 62 mm Height 60 mm 71 mm DORMA 63

64 DORMA HSW / FSW PANEL SYSTEMS HSW-R 66-72

DORMA 65

PANEL SYSTEM TYPES AND FUNCTIONS Horizontal sliding walls, fully framed, for toughened safety glass, laminated safety glass or double glazing. Robust profile frames with top, bottom brush seals and side rubber seals for elevated resistance to mechanical loading and decrease of weathering, heat loss and draughts. Prepared for toughened safety glass, laminated safety glass, double glazing or special glazing; standard fixing profile for 8 to 22 mm, other glazing thicknesses on application. Single / double action end panel Non-sliding. Doubel action end panel with floor bearing and top pivot. Optional with floor spring BTS 80 / 84. Or as single action end panel with stop and BTS 80 / 84 or Sliding panel Fixed when frontage closed. Single action sliding panel With integrated concealed door closer type ITS 96, Size 3 6; operational when frontage closed. Minimal panel width 870 mm. Double action sliding panel * With integrated concealed door closer type ITS 96, Size 3 6; operational when frontage closed. Minimal panel width 870 mm. Max. panel sizes and weights TS 92 / TS 73. Max. system height 3,000 mm 3,000 mm 3,000 mm 3,000 mm Max. panel width 1,100 mm 1,100 mm 1,100 mm 1,100 mm Max. panel weight 100 kg 100 kg 100 kg 100 kg The individual panels can also be of differing widths. The largest width should not exceed max. 115% of the smallest width. * For these panel types please consider our notes on portal systems on page 101. 66 DORMA

HSW-R SYSTEM DESIGN 72 Irrespective of the function of the individual panels, an HSW-R system comprises the following components: 75 33 ±5 75 50 60 2 2 3 4 5 6 1 Installation-efficient DORMA substructure to accommodate track rail mounting requirements (optional) 2 Track rail for bolting to the substructure 3 Carrier 4 Suspension assembly 5 Adapter frame 6 Glazing frame profile, horizontal 7 Glazing rail 8 Glazing frame profile, vertical 9 Toughened safety glass, laminated safety glass or sealed double glazing units (by others) 10 Bottom frame profile. 15 19 7 8 9 50 22 8 8 7 15 19 Floor surface 7 60 50 11 6 10 Toughened safety glass version DORMA 67

PANEL SYSTEM FIXED PANEL Single action or double action end panel with floor pivot Non-moving and always equipped with bottom deadbolt with the option of a top bolt or side action deadlock. Single action or double action options. Double action end panel Assembly types:. Floor pivot with round spindle. BTS 84 for panels up to 100 kg, with optional holdopen at 90 door opening angle. BTS 80 for panels of 100 150 kg, provided with hold-open as standard Glazing height = Total height 329 mm 7 60 50 50 75 33 ±5 75 15 15 8 63 8 63 36.5 27 Pivot bearing Single action end panel with stop plates at the top bolt. Assembly types:. Floor pivot with round spindle. As above, but with DORMA TS 73 or TS 92 overhead door closer. BTS 84 for panels up to 100 kg, with optional holdopen at 90 door opening angle. BTS 80 for panels of 100 150 kg, provided with hold-open as standard Double action end panel with floor spring BTS 84 BTS 80 8 63 45 19 65 36 Mounting dimensions BTS 80 BTS 84 a 78 108 b 60 40 c 341 306 d 51 57 51 58 b a d c 68 DORMA

HSW-R Single action end panel with TS 73 overhead door closer and additional locking device and door stop 222 45 63 193.5 205 160 140 Single action end panel with TS 92 overhead door closer and additional locking device 375 63 199 145.5 89 min. panel width 870 mm Additional locking device M6 Data and features TS 73 V TS 92 Closing strength/size EN 2 4 EN 2 4 Closing strength, variable via adjusting screw and arm hinge Closing speed adjustment via valve via valve via adjusting screw and arm hinge 3.5 50 l7 l10 Non-handed x x Latching speed adjustment via arm via arm Cushioned stay limit adjustment 75 180 80 120 Hold-open adjustment 75 160 75 150 Weight 1.8 kg 1.9 kg Length 233 mm 281 mm Overall depth 42.50 mm 47 mm Height 60 mm 65 mm DORMA 69

PANEL SYSTEM SLIDING PANELS AND CONNECTIONS Engaging the panel in the strike plate Sliding panel Sliding panel Fixed when partition is closed. The sliding panels are moving elements. Once in their closed position, they are locked down. The components available for this are provided in the bottom rail in the form of face-mounted floor bolts or deadlocks. Glazing height = Total height 329 mm 50 75 33 ±5 75 50 60 8 10 15 15 Sliding panel Strike plate l25 67 ±5 48 Engaging the panel in eccentric bushing Sliding panel min. 30 Sliding panel ±2,5 l8 Eccentric bushing l8 l25 Sliding panel to panel connections Panel to wall connection Seal Panel width Glass width = Panel width 75 mm 67 Wall connection profile with brush profile Slinding panel 51 6 51 Slinding panel 51 51 6 10 Slinding panel Double action Sliding panel Slinding panel Brush profile Abutment with articulated joint 6 90 170 Brush profile Slinding panel Single action Sliding panel Sliding panel / double or single action end panel 70 DORMA

HSW-R SLIDING PANEL WITH ITS Single action sliding panel with integrated DORMA ITS 96 concealed door closer, size 3 6 This panel type is used where passdoors only need to be opened in one direction. The single action sliding panel can be configured for either inward or outward opening. Glazing height = = Total height 329 mm 50 75 33 ±5 75 15 15 6 60 50 + 2,5 Track roller Top pivot Single action Sliding panel Face-mounted floor bolt 8 10 min. 30 Eccentric bushing l25 l8 Standard assembly top: Pivot bearing, ITS 96, size 3 6, one locking device bottom: Face-mounted floor bolt as pivot (released for sliding function) Locking device M6 8 129 73 Optional equipment top: Second locking device (for reshuffle bypass stacking) bottom: Optional second facemounted floor bolt or deadlock 3,5 l7 l10 4 15 13,5 60 110 50 DORMA 71

PANEL SYSTEM SLIDING PANEL WITH ITS Double action sliding panel with integrated DORMA ITS 96 concealed door closer, size 3 6 Double action sliding panels with DORMA ITS 96, size 3 6 door closers are characterised by their exceptional ease of installation and operation. These passdoor panels are generally equipped with a bottom deadlock and top locking device plus a bottom floor bolt operating as the pivot bearing (released for the sliding function). The ITS 96 does not feature a hold-open function as standard. Glazing height = = Total height 329 mm 50 75 33 ±5 75 8 10 15 15 6 60 50 min. 30 Single action Sliding panel + 2,5 Track roller Top pivot Face-mounted floor bolt Eccentric bushing l25 l8 For these panel types please consider our notes on portal systems on page 101. Locking device 129 73 l10 13,5 4 3,5 l7 15 M6 8 60 110 50 72 DORMA

HSW-R DORMA 73

74 DORMA HSW / FSW PANEL SYSTEMS HSW-ISO 76-82

DORMA 75

PANEL SYSTEM PANEL TYPES AND FUNCTIONS Panel types These double-glazed panels with their frames of thermal-break profiles (frame material group 2.1) offer outstanding protection against the influences of the weather, effective thermal insulation and comfortable temperatures even close to the frontage surface during seasonal changes and in the winter months. And all these effects are ideally enhanced by laterally arranged, interlocking multiple-lip seals plus automatically extending top and bottom rubber seals that are pressed against the track rail and floor when the frontage is closed. Double glazing thickness 24 49 mm. Single action door Single action panel, non-sliding, equipped with TS 92/93 door closer (optional) Sliding panel Fixed when frontage closed. Single action sliding panel for door access when frontage closed; with ITS 96 EN 3 6 concealed cam-action door closer, or with TS 92/TS 93 c am-action door Fixed panel Non-sliding side panel with top retaining brackets and bottom rail. Max. panel sizes and weights closers if required. Max. system height 3,000 mm 3,000 mm 3,000 mm 3,000 mm Max. panel width 1,100 mm 1,100 mm 1,100 mm 1,100 mm Max. panel weight 120 kg 120 kg 120 kg 120 kg The individual panels can also be of differing widths. The largest width should not exceed max. 115% of the smallest width. 76 DORMA

HSW-ISO SYSTEM DESIGN 72 Irrespective of the function of the individual panels, an HSW-ISO system comprises the following basic components: 7 8 75 75 59 67 16 1 Installation-efficient DORMA substructure to accommodate track rail mounting requirements (optional) 2 Track rail for bolting to the substructure 3 Carrier 4 Suspension assembly and bearing profile for safe and easy sliding of the panels 5 Glazing rail 6 Sealed double glazing unit (by others). Glass thickness 8 49 mm 7 Automatically extending rubber seal 8 Insulating strips in the thermal-break profile 9 Bottom frame profile 8 49 64 8 16 22 45 37 22 33 ±5 104 1 2 3 4 5 6 6 5 9 106 128 7 7 Floor surface DORMA 77

PANEL SYSTEM SINGLE ACTION DOOR WITH WALL CONNECTION 150 428 140 160 Offet hung end panel with wall connection profile Single action panel, non-sliding, operates independently of the rest of the system. The single action door with wall connection arm assembly can be swung round 170, so leaving the entire operating zone free. The closed panel is secured by a mortise centre lock. In order to provisionally determine the glazing area per panel, please apply the following formula: Approx. glazing area per panel = Panel width x total height x 0.78 The precise dimensions of the sealed double glazing units to be ordered should be exclusively taken from the approval drawing released by DORMA-Glas. Glazing height Frame height Panel height inside Total height Inward opening Outside 22 64 Inside Outward opening 59 16 22 81 37 5 5 59 5 37 81 59 16 Outside 64 22 6 59 5 59 22 Inside 78 DORMA

HSW-ISO FIXED PANEL WITH WALL CONNECTION Outside 16 59 Inside 76 22 59 Fixed panel with wall connection profile Fixed panel Non-sliding side panel that decouples from the rest of the system. The fixed panel has the same appearance as the sliding panels. Instead of the automatically extending bottom rubber seal, it features a bottom rail. Glazing height Frame height Panel height inside Total height Outside Inside In order to provisionally determine the glazing area per panel, please apply the following formula: Approx. glazing area per panel = Panel width x total height x 0.78 16 22 77 5 37 59 54 The precise dimensions of the sealed double glazing units to be ordered should be exclusively taken from the approval drawing released by DORMA-Glas. Sound protection Measurements performed by the Institute for Window Technology (Institut für Fenstertechnik e.v., Rosenheim), revealed a sound protection value of min. 27 db based on a four-panel installation. Thermal protection The heat transfer coefficient Uw will be calculated according to DIN EN 10077-1. Example value: Panel B 900 x H 2,500, Ug (glass) = 1.1 W/m 2 K, Uf (frame) = 2.6 W/m 2 K, Uw = 1.9 W/m 2 K The values necessary for calculating the U w value are indicated in DIN EN ISO 10077-1:2006. Data and features TS 92 TS 93 Closing strength/size EN 2-4 EN 2-5 EN 5-7 Closing force, variable via adjusting screw via adjusting screw via adjusting screw Closing speed adjustment via valve via valve via valve Non-handed yes yes yes Latching speed adjustment via valve via valve via valve Cushioned stay limit adjustment 80 120 80 120 80 120 Hold-open adjustment 75 150 75 150 75 150 Weight 1.9 kg 3.5 kg 5.2 kg Length 281 mm 275 mm 285 mm Overall depth 47 mm 53 mm 62 mm Height 65 mm 60 mm 71 mm DORMA 79

PANEL SYSTEM SLIDING PANEL Sliding panel Fixed when the frontage or partition is closed. The sliding panels are the moving elements. Once in their closed position, they are locked down. Face-mounted floor bolts are available as an option for the bottom glazing rail. 6 Glazing height Frame height Panel height inside Total height In order to provisionally determine the glazing area per panel, please apply the following formula: Approx. glazing area per panel = Panel width x total height x 0.78 The precise dimensions of the sealed double glazing units to be ordered should be exclusively taken from the approval drawing released by DORMA-Glas. Horizontal sections of the sliding panels with connection details Sliding panel to wall connection profile Sliding panel to sliding panel Outside 16 77 5 37 Outside 16 77 5 59 16 64 64 22 59 6 54 22 22 59 6 76 Inside Inside 80 DORMA

HSW-ISO SLIDING PANEL WITH ITS 300 184 ITS 96 door closer integrated in the profile (concealed installation) Single action sliding panel with integrated ITS 96 3-6 This panel type is installed where doors need to be opened in one direction. The cam-action door closer can be fitted so that the single action panel is either inward or outward opening. Glazing height Frame height Standard assembly top: Pivot bearing, ITS 96, size 3 6 one locking device bottom: Face-mounted slide bolt as pivot (released for sliding function) Optional equipment top: Second locking device (for reshuffle bypass stacking) bottom: Optional second facemounted slide bolt 6 Horizontal section of single action panels, inward or outward opening Function of the top locking device Outward opening 81 5 59 16 22 16 Status of locking device for door operation 129 Status of locking device for sliding 129 64 Panel height outside Total height 22 22 22 59 5 81 Inward opening DORMA 81

PANEL SYSTEM RESHUFFLE BYPASS CONFIGURATION Stacking in the reshuffle bypass configuration This special stacking arrangement is applied when the panels should be parked in a niche and no single action end panel should be visible in the frontage. Please also see the following illustrations. Sliding panel in bypass travel mode (sliding end panel) Single action sliding panel in bypass travel mode (outward opening only) 82 DORMA

HSW-ISO DORMA 83

84 DORMA ACCESSORIES Vertical Seals Overview 86-87 Vertical Sealing Profiles 88-95 Floor Track 96-97

DORMA 85

ACCESSORIES RETROFITTABLE PROFILES The following retrofittable profiles are available to provide the necessary lateral sealing so that the horizontal sliding can be made draught-proof for winter operation. 4 Clear plastics profile (not for single/double action end panels or double action sliding panels) for 10 and 12 mm glass 10 (12) Glass joint gasket for 10 12 mm glass, adhesive, milky transparent 4 86 DORMA

VERTICAL SEALS OVERVIEW VERTICAL SEALING PROFILES The vertical sealing profiles provide protection of the exposed lateral glass edges of the HSW panels. In addition, the integral double brush seals ensure excellent draft-proofing. The sealing profiles are individually tailored to the requirements of the bottom glazing rails, so they are already prepared for the locking devices such as floor bolts, end pins and vertically engaging deadlocks. At the top, a degree of extra length is provided to enable precise sealing profile adaptation to the exact panel height once the system has been vertically aligned. 5.5 1 13 Vertical Sealing Profile 33 10 (12) 2 5.5 13 Vertical Sealing Profile 33 2 DORMA 87

ACCESSORIES VERTICAL SEALING PROFILES 32.5 End panel Non-sliding, always fitted with a bottom deadlock. With additional top bolt or side-action deadlock as options either as single action or double action end panel. As-delivered condition of the vertical sealing profiles: Cut lengths supplied from factory = Partition height 110 mm. As-delivered length (total height 110 mm) M4 Adapt profile length on site 20 25 58.5 58.5 Holes and recesses are pre-machined in the profile for the bottom glazing rail only. Any further machining work required for connection to the top glazing rail has to be performed on site. Bottom drill hole or recess for end-mounted floor bolt machined by DORMA-Glas 33 5.5 5.5 1 10 (12) Installation instructions When fitting the glazing rails, please ensure that the glass protrusion is even over the full length. Prior to profile machining, first hang the panels from the overhead track and then align. 88 DORMA

VERTICAL SEALING PROFILES Sliding panels Stationary once frontage closed and secured. Sliding panels are fixed in position when the partition is closed. Face-mounted sliding bolts and deadlocks are available for incorporation in the bottom glazing rail. As-delivered length (total height 110 mm) 32.5 M4 Adapt profile length on site 20 25 Sliding panel As-delivered condition of the vertical sealing profiles: Cut lengths supplied from factory = Partition height 110 mm. Holes and recesses are pre-machined in the profile for the bottom glazing rail only. Any further machining work required for connection to the top glazing rail has to be performed on site. Bottom drill hole or recess for end-mounted floor bolt machined by DORMA-Glas Installation instructions When fitting the glazing rails, please ensure that the glass protrusion is even over the full length. Prior to profile machining, first hang the panels from the overhead track and then align. 2 1 5.5 33 DORMA 89

ACCESSORIES VERTICAL SEALING PROFILES Profile to upper face of brush carrier Sliding panels in segmented configurations Stationary once frontage closed and secured. Sliding panels are fixed in position when the partition is closed. Face-mounted sliding bolts and deadlocks are available for incorporation in the bottom glazing rail. As-delivered length (total height 110 mm) 32,5 Adapt profile length on site 25 20 Sliding panel As-delivered condition of the vertical sealing profiles: Cut lengths supplied from factory = Partition height 110 mm. Holes and recesses are pre-machined in the profile for the bottom glazing rail only. Any further machining work required for connection to the top glazing rail has to be performed on site. Installation instructions When fitting the glazing rails, please ensure that the glass protrusion is even over the full length. Prior to profile machining, first hang the panels from the overhead track and then align. 5.5 1 12 33 5.5 1 25 33 1 5.5 33 90 90 DORMA

VERTICAL SEALING PROFILES 33 RTS 85 RTS double action sliding panel Double action sliding panel with RTS transom-concealed door closer in closed frontage. Face-mounted sliding bolts and deadlocks are available for incorporation in the bottom glazing rail. As-delivered condition of the vertical sealing profiles: Cut lengths supplied from factory = Partition height 110 mm. Holes and recesses are pre-machined in the profile for the bottom glazing rail only. Any further machining work required for connection to the top glazing rail has to be performed on site. As-delivered length (total height 110 mm) Adapt profile length on site 20 20 Bottom drilling and machining work for end-mounted sliding bolt performed by DORMA-Glas GmbH Installation instructions When fitting the glazing rails, please ensure that the glass protrusion is even over the full length. Prior to profile machining, first hang the panels from the overhead track and then align. 2 1 5.5 60.5 Double action sliding panel with RTS 33 Sliding panel DORMA 91

ACCESSORIES VERTICAL SEALING PROFILES Door rail 33 Double action sliding panel with ITS 96 Double action sliding panel with ITS 96 integrated door closer in closed frontage. Face-mounted sliding bolts and deadlocks are available for incorporation in the bottom glazing rail. As-delivered length (total height 110 mm) Adapt profile length on site 25 20 60.5 As-delivered condition of the vertical sealing profiles: Cut lengths supplied from factory = Partition height 110 mm. Holes and recesses are pre-machined in the profile for the bottom glazing rail only. Any further machining work required for connection to the top glazing rail has to be performed on site. Bottom drilling and machining work for end-mounted sliding bolt performed by DORMA-Glas GmbH 2 1 5.5 32 Installation instructions When fitting the glazing rails, please ensure that the glass protrusion is even over the full length. Prior to profile machining, first hang the panels from the overhead track and then align. 92 DORMA

VERTICAL SEALING PROFILES 33 Lock with lever handle and strike box optional. 80 175 l50 57 Folding sliding panel Hinged, with lock and magnetic fixing devices top and bottom for securing the folding panel to the sliding panel ready for transfer. 1050 As-delivered condition of the vertical sealing profiles: Cut lengths supplied from factory = Partition height 110 mm. OKFF 7 Holes and recesses are pre-machined in the profile for the bottom glazing rail only. Any further machining work required for connection to the top glazing rail has to be performed on site. Installation instructions When fitting the glazing rails, please ensure that the glass protrusion is even over the full length. Prior to profile machining, first hang the panels from the overhead track and then align. DORMA 93

ACCESSORIES VERTICAL SEALING PROFILES 33 64 43 132 16,5 ITS 96 single action or double action sliding panels with Universal centre lock and Universal keeper Double action sliding panel with ITS 96 integrated door closer in closed frontage. Face-mounted sliding bolts and deadlocks are available for incorporation in the bottom glazing rail. OKFF 132 7 As-delivered condition of the vertical sealing profiles: Cut lengths supplied from factory = Partition height 110 mm. Holes and recesses are pre-machined in the profile for the bottom glazing rail only. Any further machining work required for connection to the top glazing rail has to be performed on site. Installation instructions When fitting the glazing rails, please ensure that the glass protrusion is even over the full length. Prior to profile machining, first hang the panels from the overhead track and then align. 94 DORMA

VERTICAL SEALING PROFILES Profile machining For end-mounted and facemounted sliding bolts performed by DORMA-Glas GmbH. Vertical sealing profiles with end-mounted slide bolt 5.5 1 Preparation of vertical sealing profile for face-mounted sliding bolt and mounting 2 11 Latching pin 60 30 41 21 11 M4x18 M4x10 44 32.7 20.5 Preparation of vertical sealing profile for face-mounted sliding bolt Vertical sealing profiles with face-mounted slide bolt 5.5 1 2 60,5 105,5 30 32.7 20 66 Tool for preparing the top of vertical sealing profiles Tool for preparing vertical sealing profiles Article number 828.231.000.99 DORMA 95

ACCESSORIES FLOOR TRACK FOR SLIDING PANELS Sliding panel A floor track in the form of a stainless steel channel section (U-profile) is also available as an option. This can be used for HSW-G and HSW-R sliding panels irrespective of the partition layout. In special cases and after technical clarification, it may also be used with HSW-GP sliding panels. For this, the endmounted floor bolt usually applied for straight-line partition configurations is replaced by a combination of guide pin and end pin. The guide pin must be vertically below the track roller and is adjustable in the range +/ 10 mm. For abutment to single action/ double action end panels and also in the case of angled configurations, a face-mounted floor bolt is replaced by a bottom deadlock. Glazing height = Total height 308 mm 21 20 25 9 7 14.5 100 100 35 33 ±5 75 2.5 4 65 Sliding panel 65 Hex head bolt M6 x 35, 10 mm A/F The floor track is available in three designs:. Straight. 90 curve. 135 curve. The individual track sections are abutted and fixed in place by means of a stainless steel connector. In its as-delivered condition, the floor track comes with a welded flange for fixing to the unfinished floor. This can be removed if not required. 90 curve 135 curve Straight 96 DORMA

FLOOR TRACK FLOOR TRACK STACKING TRACK DETAIL Floor track Floor track max. length 3000 mm 20 1 12.5 ±1 R1 (19) (10.5) 90 Floor track connector 50 11 Floor track connector (14.5) 10 R1 R100 40 40 135 276 R100 40 90 40 214 120 12.5 ±0,3 Floor fixing flange Can be removed if not required 91 1 HSW floor track configuration with a 90 stacking track arrangement HSW floor track configuration with a 135 stacking track arrangement HSW floor track configuration with a parallel stacking track arrangement 214 DORMA 97

98 DORMA GENERAL INFORMATION Measuring Up 100 General Information 101-102

DORMA 99