INSTLLTION INSTRUCTIONS FOR PRT 99-700 KIT FETURES 99-700 DIN Head unit provision with pocket ISO DIN Head unit provision with pocket DDIN Head unit provision ISO Stacked Head unit provision Painted Silver to Match Factory PPLICTIONS Mitsubishi Eclipse 006-0 KIT COMPONENTS ) Radio Housing ) ISO rackets C) ISO Trim Plate D) DDIN rackets E) Pocket F) DDIN Trim Plate C D E F WIRING ND NTENN CONNECTIONS (Sold Separately) Wire harness: MITO-0 Mitsubishi amp interface harness 006-up 70-700 Mitsubishi harness 99-up ntenna adapter: Not required TOOLS REQUIRED: Phillips Screwdriver Small Flat lade Screwdriver -800--09 www.metraonline.com COPYRIGHT 004-00 METR ELECTRONICS CORPORTION
99-700 TLE OF CONTENTS Dash Disassembly Mitsubishi Eclipse 006-0............................ Radio Housing ssembly............................... Kit ssembly....................................., 4 Final ssembly...................................... 5 KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-54-678 for more information and take steps toward a better tomorrow.
99-700 DSH DISSSEMLY MITSUISHI ECLIPSE 006-0 Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip and remove the trim panel including the radio a/c vents (Figure ) Remove (4) Phillips screws securing radio chassis to dash to remove. (Figure ) 4 Unclip and remove the a/c vents from the factory radio trim panel. (Figure C) 5 Unclip and remove the hazard switch from the factory radio trim panel. (Figure D) D C RER VIEW
99-700 KIT SSEMLY RDIO HOUSING SSEMLY Clip the a/c vents into the 99-700 radio housing. (Figure ) Clip the hazard switch into the 99-700 radio housing. (Figure )
99-700 KIT SSEMLY DIN HED UNIT PROVISION Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure ) Slide the aftermarket head unit into the cage and secure. (Figure ) Snap the pocket into the radio housing. (Figure ) ISO DIN HED UNIT PROVISION 4 Mount the ISO rackets to the head unit with the screws supplied with the unit. (Figure ) Slide the head unit into the radio opening until the side clips engage. (Figure ) Snap the ISO Trim Plate into the Radio Housing. (Figure ) Snap the pocket into the radio housing. (Figure )
99-700 KIT SSEMLY DOULE DIN HED UNIT PROVISION Cut the center bar rib. Slide the appropriate bracket into the radio housing aligning the holes in the radio housing with the holes on the bracket. (Figure ) Slide the DDIN radio unit into the DDIN bracket/radio housing assembly and secure the unit to the kit using the screws supplied with the head unit. (Figure ) 4 Snap the DDIN Trim Plate into the rado housing. (Figure ) STCKED ISO DIN HED UNIT PROVISION Cut the center bar rib. Slide the appropriate bracket into the radio housing aligning the holes in the radio housing with the holes on the bracket. (Figure ) Slide the stacked ISO DIN units into the DDIN bracket/radio housing assembly and secure the units to the kit using the screws supplied with the head units. (Figure ) 4 Snap the DDIN Trim Plate into the rado housing. (Figure ) 4
FINL SSEMLY Locate the factory wiring harness in the dash and make the connection as shown. Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disassembly. FINL WIRING CONNECTIONS Make wiring connections using the EI color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit. 99-700 FINL SSEMLY C ) Strip wire ends back /" ) Twist ends together C) Solder D) Tape D METR / EI WIRING CODE V Ignition / cc... Red V att / Memory.. Yellow Ground........... lack* Power ntenna..... lue mp Turn-On...... lue / White mp Ground....... lack / White Illumination........ Orange Dimmer.......... Orange / White Right Front (+)..... Gray Right Front (-)...... Gray / lack Left Front (+)...... White Left Front (-)....... White / lack Right Rear (+)...... Violet Right Rear (-)...... Violet / lack Left Rear (+)....... Green Left Rear (-)....... Green / lack *NOTE: When lack a wire is not present, ground radio to vehicle chassis. ll colors may not be present on all leads due to manufacturer s specifications. 5
99-700 INSTRUCTIONS REV. 09/0/0-800--09 www.metraonline.com COPYRIGHT 004-00 METR ELECTRONICS CORPORTION INST99-700