Installation instructions, accessories Instruction No 30756560 Version 1.2 5 Part. No. 30756177 Multimedia monitor with DVD, Dual screen Volvo Car Corporation Multimedia monitor with DVD, Dual screen- 30756560 - V1.2 Page 1 / 55
Equipment IMG-242205 A0000162 IMG-262943 IMG-239942 IMG-239981 IMG-317184 Page 2 / 55
IMG-317185 Page 3 / 55
IMG-317186 Page 4 / 55
IMG-213320 Page 5 / 55
INTRODUCTION Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer. Note! There are two versions of cable harness for the tunnel console, with or without preparations for Digital TV receivers. The images in the installation instructions show cable harness without Digital TV receiver. 1 Slide both the front seats all the way back and upwards all the way at the front and rear edge. Press the headrest downwards. Find the headrest's two locks on the back of the seat. Press in the catches and pull the headrest upwards at the same time. The seats may require lowering slightly at the rear edge again so that the headrest can be pulled out of the backrest completely. Therefore lower the seat as much as possible so that the headrest can be released and removed. Remove the headrest on both front seats and allow the seats to remain in the same position. IMG-256044 Page 6 / 55
2 Remove both the side panels from the tunnel console. R8504225 3 Remove the sound barrier on the driver's side by first removing the two screws and then prizing it away at the top edge. R8504495 Page 7 / 55
4 Pull the handle (1), move the tunnel compartment backward and lift it away (2). IMG-238927 5 Remove the cover. It shall not be re-used. R8503994 Page 8 / 55
6 Applies to cars with automatic gearbox Turn the ignition key to position II. Applies to all models Move the gear selector lever to its rearmost position. Use a weatherstrip and pry off the gear selector panel at the rear edge. R8504113 7 Turn the ignition key to position 0. Note! Wait at least three minutes before unplugging the connectors or removing other electrical equipment. IMG-245980 Page 9 / 55
8 Press in the catches underneath and remove the panel. IMG-239204 9 Remove the small storage compartment. IMG-268403 Page 10 / 55
10 Applies to cars with telephone Unhook and disconnect the connector (1). Disconnect the telephone cable from the load-removing grommet (2). Release the telephone cable. Remove the handset. Remove the screw (3). Push the catch to one side (4). Remove the telephone cradle. R3904067 11 Applies to all models Remove the six screws. IMG-268404 Page 11 / 55
12 Lift up and remove the upper section. At the same time disconnect the connector to the AUX socket. IMG-268405 13 Disconnect the connector. Press in the catches and unhook it from the tunnel console. IMG-268406 Page 12 / 55
14 Remove the two screws and lift out the tunnel console. IMG-268407 15 Take the cable harness (C) from the kit and position it as illustrated. The junction (1) must be at the rear edge of the SRS control module. The cable marked with blue tape must go to the right seat and the other to the left seat. The cable with 2 x 4 pin connectors must be routed forward on the driver's side. IMG-317323 Page 13 / 55
16 Route the cables in the join for the floor mats further along the seat rail. Position the cable in a loop under the seat. IMG-268409 17 Take the cable with the two 4 pin connectors and route forward on the driver's side. IMG-268410 Page 14 / 55
18 Carry out points 18-45 on both sides of the seats Remove the screw for the seat's side panel. IMG-268411 19 Turn the panel upwards at the front edge. Unhook it from the seat at the rear edge. IMG-268412 Page 15 / 55
20 Remove the knob for the lumbar support adjustment by removing the cover using a small screwdriver and pull the knob straight off. IMG-268413 21 Take a long cable tie from the kit and insert it through the hole for adjusting the lumbar support and inside the upholstery. The cable tie must be routed between the thin foam of the upholstery and the support pad. IMG-268414 Page 16 / 55
22A Illustrations A and B Remove cable harness (A) from the kit. Tape the cable terminals on the cable tie. Tape together as flat as possible. (Image B) Route the cable harness through and out at the headrest hole. Remove the cable tie from the cable harness. 22B IMG-262949 IMG-317223 23 Applies to the right-hand front seat Thread the cable tie from the headrest's inner mounting down to the hole for lumbar adjustment. The cable tie must be routed between the upholstery's thin foam and the protective pad (also see image 29). IMG-262950 Page 17 / 55
24 Applies to the left-hand front seat. Thread the cable tie from the headrest's outer mounting down to the hole for lumbar adjustment. The cable tie must be routed between the upholstery's thin foam and the protective pad (also see image 29). IMG-262952 25 Applies to both seats Tape the cable harness on the cable tie. Tape as flat as possible. See image 22 B. Pull it up towards the upper edge of the seat and out through the hole for the headrest. Remove the cable tie and tape from the cable harness. IMG-262951 Page 18 / 55
26 Caution! There are two brown cables in the cable harness. The brown cable to terminal 4 is twinned with the blue cable to terminal 3. Position: IMG-317224 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Not connected. White (W) Blue (BL) Brown (BN) Red/White (R/W) Red (R) Black (SB) Brown (BN) Yellow (Y) Green (GN) Gray (GR) Pink (P) 27 Take the grey connector from the kit. Connect the cable harness terminals according to point 26. Press in the connector's catch. IMG-317243 Page 19 / 55
28 Adjust the length on the cable harness so that the connector protrudes 140mm. The cable harness must be positioned in front of the hole for the headrest. IMG-317244 29 Using your fingers, press the cable harness under the protective pad, the cable harness must not press out the upholstery after installation. 1. Padding 2. Protective pad IMG-262956 Page 20 / 55
30 Take the headrest and the upholstery from the kit. Pull the upholstery over the headrest. IMG-317245 31 Pull the two corners of the upholstery over. IMG-317263 Page 21 / 55
32 Hook the upholstery onto the two cutouts. IMG-317325 33 Fold in the upholstery's two reinforcements. IMG-317326 Page 22 / 55
34 Fold up the upholstery's reinforcement. Locate the hole under the upholstery on the side of the headrest. Note! The inward facing side in the car. Make a mark for making a hole using a piece of tape. Fold back the upholstery's reinforcement. IMG-317327 35 Install the 5 clips. IMG-317328 Page 23 / 55
36 Fold in the upholstery's mounting. IMG-317329 37 Take the display from the kit. Install on the headrest. IMG-317330 Page 24 / 55
38 Align the display in the headrest's two cutouts. IMG-317331 39 Install the two screws. IMG-317332 Page 25 / 55
40 Locate the hole under the upholstery on the headrest side, marked with tape. Make a hole in the upholstery using a scriber or an awl. Note! The inward facing side in the car. IMG-317333 41 Take the coat hook from the kit. Press into the hole. Tap it in lightly using a plastic hammer so that it secures properly. IMG-317334 Page 26 / 55
42 Position the panel on the seat. Position the cable harness in the panel's cutout. IMG-317335 43 Install the headrest on the seat. Only slide it down so that the distance between the seat and lower edge of the headrest is approximately 50mm. IMG-317336 Page 27 / 55
44 Connect the connector and push the headrest down to the locked position. Check that the head restraint has locked into place by pulling it upwards. IMG-317337 45 Check that the headrest upholstery is correctly aligned against the panel. Repeat steps 18-45 for the other side. IMG-317338 Page 28 / 55
46 Applies to the right-hand front seat and cars without heated seats Take a clip with cable tie from the kit and install it on the plate edge on the left-hand side of the right-hand seat. IMG-263002 47 Take the cable harness from the headrest and pull forward, in underneath the seat. Follow the cable harness for the seat belt buckle. Tighten the cable tie (1). Secure the cable using two cable ties (2). IMG-263003 Page 29 / 55
48 Applies to the right-hand front seat and cars with heated seats Take the cable harness from the headrest and pull forward, in underneath the seat. Follow the cable harness for the heating element. Secure the cable using three cable ties (1). IMG-263004 49 Applies to the right-hand front seat Route the cable harness in an arc under the seat. Secure it using three cable ties in the existing cable harness. IMG-263005 Page 30 / 55
50 Take a piece of foam tape from the kit and cut it in the centre. Fold the seat forward slightly and connect the cable harness from the floor to the connector (1). Tape one cut piece of foam tape around the connectors. Place a cable tie on each side of the connectors and tighten. Check that the cable harness is not trapped when the seat is slid forwards and backwards. The right-hand seat means the passenger seat Fold the backrest forward and backwards and check that the cable harness is not trapped when folding the backrest. IMG-263006 51 Applies to the left-hand seat and cars without heated seats Take a clip with cable tie from the kit and install it on the plate edge on the right-hand side of the left-hand seat. IMG-263009 Page 31 / 55
52 Take the cable harness from the headrest and pull forward, underneath the seat. Follow the cable harness for the seat belt buckle. Tighten the cable tie (1). Secure the cable using two cable ties (2). IMG-263010 53 Applies to the left-hand front seat and cars with heated seats Take the cable harness from the headrest and pull forward, in underneath the seat. Follow the cable harness for the heating element. Secure the cable using three cable ties (1). IMG-263011 Page 32 / 55
54 Applies to the left-hand front seat. Route the cable harness under the seat. Connect the cable harness from the floor to the connector (1). Secure it using a cable tie in the existing cable harness or in a bracket. Tape one cut piece of foam tape around the connectors. Place a cable tie on each side of the connectors and tighten. Check that the cable harness is not trapped when the seat is slid forwards and backwards. The left-hand seat means the passenger seat IMG-263012 Fold the backrest forward and backwards and check that the cable harness is not trapped when folding the backrest. 55 Applies to all models Fold the ashtray out, press it down and remove IMG-268416 Page 33 / 55
56 Pull out the cup holder to its limit position. IMG-268417 57 Turn the tunnel console. Lift up the catch and remove the cup holder. IMG-268418 Page 34 / 55
58 Remove the four screws. IMG-268419 59 Pull the opening handle. Remove the two screws and lift off the lower section. IMG-268444 Page 35 / 55
60 Fold the cover up and remove the two screws. Remove the cover by sliding it forward. The cover will not be reused. IMG-268445 61 Remove the plug for the 12 V socket. Remove the two rubber supports. IMG-268446 Page 36 / 55
62 Lift up the two catches and remove the inner section of the ashtray. It will not be reused. IMG-268447 63 Release the two catches and remove the 12 V socket. IMG-268448 Page 37 / 55
64 Mark as illustrated on the tunnel console's storage compartment. Pre-drill using a Ø 2.5 mm (3/32") bit. Drill out the hole. Use a Ø35 mm (1 3/8") diameter hole saw. Smooth off the hole edges. IMG-268450 65 Points 65-66 apply when the tunnel console is not prepared for the RSE system Mark as illustrated on the tunnel console's upper section. Drill using a Ø 5mm (13/64") bit. IMG-268451 Page 38 / 55
66 Mark as illustrated on the tunnel console's upper section. Saw and cut out the hole according to the markings. IMG-268452 67 Applies to all models Take the lower section of the cover and cable harness (B) from the kit. Insert the end with the three (4 x with Digital TV receiver) connectors through the hole. Install the rubber grommet. IMG-268453 Page 39 / 55
68 Secure the cable harness with a tie strap. IMG-268454 69 Take the DVD unit and 4 M4x6 screws from the kit. Connect the three (4 x with Digital TV receiver) connectors to the DVD unit. IMG-268456 Page 40 / 55
70 Place the DVD unit in the lower section of the cover as illustrated. Ensure that the cable harness goes under the DVD unit and does not protrude towards the open button or screw tower. Install the four screws and tighten. IMG-268457 71 Take the cover's upper section and 4 screws, PF5x16, from the kit. Install the cover. IMG-268458 Page 41 / 55
72 Turn the cover, install the four screws and tighten to 3 Nm (2.2 lbf.ft.). IMG-268467 73 Route the cable harness in from the DVD unit through the drilled hole and down on the right-hand side of the tunnel console. Install the rubber grommet. Check that the rubber grommet's flanges are against the console. IMG-268459 Page 42 / 55
74 Take the AV panel from the kit. Connect the green connector to it. IMG-268460 75 Install the 12 V socket to the panel. IMG-268464 Page 43 / 55
76 Secure the cable harness clips on the flange of the AV panel. IMG-268466 77 Press the panel into place. Secure the panel with one screw (ST 3.5x13) from the kit. IMG-268468 Page 44 / 55
78 Reinstall the rubber support, the ashtray and the plug for the 12 V socket. IMG-268471 79 Install the cover on the tunnel console and tighten with the two screws. IMG-268472 Page 45 / 55
80 Open and close the cover three times. Check that the lock at the front edge works and that the rubber bushings are in place. The cable harness should be in a loop as illustrated. IMG-268473 81 Turn the console and route the cable harness as illustrated. IMG-268476 Page 46 / 55
82 Thread the cable harness out through the square cut out on the lower section of the tunnel console. Secure the two clips of the cable harness on the plastic flanges. Tighten the lower section using the 6 screws. IMG-268487 83 Take a cable tie and secure the 12V socket's cable by the clip on the cable harness from the DVD unit. The cable tie catch should point towards the outer side of the tunnel console. Reinstall the cup holder. IMG-268488 Page 47 / 55
84 Make marks for drill holes on the opening handle for the tunnel console as illustrated. Pre-drill using a Ø 2.5 mm (3/32") bit. Drill out the hole using a Ø 6 mm ( 15/64") drill bit. IMG-268489 85 Take the cover and 2 x PF5x12 screws from the kit. Install the cover on the opening handle. Digital TV receivers must then be installed: Continue with the installation instructions: TV receiver, digital. IMG-268490 Page 48 / 55
86 Reinstall the front tunnel console and at the same time pull up the connectors for the RSE system, 12 V socket and telephone if applicable. IMG-268491 87 Connect the 4 pin black connector from the cable harness (B) to the one disconnected from the AUX socket. IMG-268492 Page 49 / 55
88 Take the upper panel for the front tunnel console. Remove the AUX socket by releasing the catches at the front and rear edge. IMG-268493 89 Take the new AUX socket from the kit and connect it to the 7 pin connector from cable harness (B). Install the socket in the panel with the connector's catch backwards. IMG-268494 Page 50 / 55
90 Install the tunnel console's upper panel. Check that the panel hooks securely at the front edge. Reinstall the tunnel console's 8 screws and tighten them. IMG-268496 91 Applies to cars with telephone Reinstall the telephone cradle with the screws (3). Route the telephone cable. Install the telephone cable in the load-removing grommet (2). Connect the connector (1). IMG-268497 Page 51 / 55
92 Applies to all models Connect the connector for the 12V socket. IMG-268498 93 Take the rear tunnel console. Connect the two connectors for the RSE system (3 x with Digital TV-receiver.) Take two pieces of foam tape from the kit and wrap them around the connectors. Cut off the foam tape excess. IMG-268499 Page 52 / 55
94 Insert the connectors into the tunnel console. Hook the connector on for the 12 V socket. Slide the rear tunnel console forwards in its grooves until it locks and check that the cable harness is not trapped. IMG-268500 95 Take the cable with the 2 x 4 pin connector and route forward on the driver's side. Fold the carpet to one side and place the cable underneath. IMG-268501 Page 53 / 55
96 Locate the 4 pin, grey connector for the power supply. It is secured on the thick cable harness under the dashboard on the driver's side. Note! The pre-routed connector is already connected on certain versions. IMG-241303 97 Connect the cable harness to the existing connector (1). Wrap a piece of foam tape around the connected connectors and cut off the excess. Install the connector (2) on the car's existing cable harness using a cable tie. Note! The pre-routed connector is already connected on certain versions. In such a case, disconnect it and connect both connectors from the new cable harness. Wrap a piece of foam tape around the connectors. IMG-268502 Reinstall: the small storage compartment the panel at the gear selector side panels the sound barrier Page 54 / 55
98 Install the batteries in the remote control and headsets. Region code the DVD player. Information is in VIDA under: Product specifications Design and Function 39 Media, communication and navigation 393 Equipment for entertainment Rear seat entertainment system Design To activate the TV function IMG-275777 1. 2. 3. 4. 5. Aim the remote control at the screen and press DAY/NIGHT ("on/off") for approx. 5 seconds until SERVICE MENU is displayed. Enter code 1971, press OK. Select SET TV, press OK. Select TV connected, press OK. Exit. 99 Installing decals (Only applies to USA and Canada) Take the black decal from the kit. Clean the area (1) where the decal will be located. Use a mixture of 30% windscreen washer fluid and 70% water. Wipe dry. Remove the backing paper from the adhesive side of the decal. Secure the decal as illustrated. Press the decal into place properly. R8903555 Page 55 / 55