OIL FILLER ND IR RETHER FILLER CPS The complete series of oil filter and makes it possible to meet all market demands. Metal and plastic styles suitable for use on mobile equipment are available. s perform a dual function, air filtration at the tank inlet and prefiltration of the fluid by means of the basket, in order to prevent the ingress of foreign material into the tank during filling and top-up operations. Correct operation of breather filters makes for longer life of the filter cartridges installed in the hydraulic circuit, and in applications where high level of contamination are present. Temperature from -5 C to +00 C Compatibility NR seals and Cork Gasket, compatible with: Mineral oils to ISO 94 - aqueous emulsions Synthetic fluids, glycol water. FPM seals, compatible with: Synthetic fluids type HS-HFDR-HFDS-HFDU. 0
Metal oil filler and air Series T 46 4 5 6 4 ayonet connection Ø 46 7 8 46 Reservoir holes T46 (Materials) M5 - Cover: Chrome Plated Steel - Filter element: Impregnated paper Polyurethane 64-6 - Flange: Galvanised Steel 4 - Seals: NR Cork Gasket 5 - Screws: Galvanised Steel 7 - Chain, ring: rass Ø 8 Ø 5 Ø 0 Ø 4 8 - asket: Galvanised Steel Flow rates with Δp: 0,0 bar Filtration T 46 l/min µm 50 0 µm 00 T 46: 0,00 kg ayonet connection Non-removable strainer 4 5 6 7 T46 Example: T46 0 0 C P0 - Connection to reservoir 5 - Variants Flange with bayonet connection 0 Standard - Filter element 0 µm - Impregnated paper C 6 - asket With chain - Seal 0 0 µm - Polyurethane L= 65 mm NR 7 - Options Cork gasket P0 MP Filtri standard 4 - Valves valves
Series TP 50 Nylon oil filler and air 4 5 6 4 ayonet G /4 TP50 (Materials) - Cover/ringnut: Nylon - Filter element: Impregnated paper Polyurethane - Pressurisation valve: Nylon Galvanised Steel NR 4 - Seal: NR Reservoir holes 5 - Flange: Nylon 6 - Screws: Galvanised Steel M5 7 - asket: Nylon Flow rates with Δp: 0,0 bar Filtration l/min 0 µm 0 Quantity per pack Number of Parts TP50 0 65 Ø TP50: 0,060 kg Ø 4 Ø Ø 5 4 5 6 TP50 Example: TP50 0 0 P0 - Connection to reservoir 4 - Valves Flange with bayonet connection C Flange with bayonet connection G /4 - Filter element 0 µm - Impregnated paper 0 0 µm - Polyurethane - Seal NR 0,5 bar pressurisation valve 5 - asket L= 65 mm 6 - Options P0 MP Filtri standard
Series T 80 Metal oil filler and air 4 5 6 5 7 5 8 9 T80 /D (Materials) - Cover: Chrome Plated Steel - Filter element: Impregnated paper Polyurethane - Pressurisation valve: odies: Nylon End cap-disk: Galvanised Steel Spring: Steel Seals: NR 4 - Flange and anti-splash feature: Galvanised Steel 5 - Seals: Cork Gasket NR 6 - Screws: Galvanised Steel 7 - Flange: Galvanised Steel 8 - Chain, ring: rass 9 - asket T80: Galvanised Steel Flow rates with Δp: 0,0 bar Filtration l/min µm 450 0 µm 550 Strainer L 80 mm: 0,0 Kg Strainer L 50 mm: 0,50 Kg T 80 ayonet connection Non-removable basket T 80 ayonet connection With Padlock tab T 80 D ayonet connection Removable basket T8000...P0 T800...P0 T800.9..P0 T800...P0 ayonet connection ayonet connection ayonet connection ayonet connection Closed filler cap without with filter with anti-splash with filter element element feature and filter element pressurisation valve and filter element 4
ayonet connection Weld flange 58 Ø 80 Ø 6,5 Ø 80 55 6 4,5 Reservoir holes Ø 7 L* Ø 5 00 Ø 50 Ø 8 M5 Ø 7 Ø 40 Ø 8 4 5 6 7 T80 Example: T80 0 L P0 - Connection to reservoir 5 - Variants Flange with bayonet connection 0 Standard D Weld flange L With Padlock tab ( versions only) - Filter element 0 filter (lank filler cap) 0 µm - Impregnated paper 0 0 µm - Polyurethane - Seal 6 - asket *L= 80 mm ( versions only) * L= 50 mm ( versions only) *L= 00 mm (D versions only) NR 7 - Options Cork gasket P0 MP Filtri standard 4 - Valves 9 0, bar pressurisation valve (only with seals NR) 0,7 bar pressurisation valve (only with seals NR) nti-splash feature (only with filter element µm) 5
Series TP 90 Nylon oil filler and air TP90 (Materials) Flow rate with Δp: 0,0 bar 6 4 - Cover/ringnut: Nylon - Filter element: Impregnated paper Polyurethane - Pressurisation valve: Nylon Galvanised Steel NR 4 - Seal: NR Filtration l/min µm 450 0 µm 550 asket L 0 mm: 0,50 Kg asket L 50 mm: 0,0 Kg 5 5 - Flange : Nylon 6 - Screws: Galvanised Steel 7 4 7 - Padlock tab: Galvanised Steel 8 - Chain, ring: rass 8 9 0 9 - Dipstick: Phosphated Steel 0 - asket: Galvanised Steel/Nylon TP90... Flange with bayonet connection TP90 R... Flange with M5x connection TP90 F... Flange with spigot DIN 4557 Connection M5x TP90 C... Weld riser Connection M5x External chain Internal chain Internal chain Weld riser in Galvanised Steel, internal chain TP90 -C-R-F TP90 -C-R-F TP90 -C-R-F TP90 -C-R-F With dipstick Closed filler cap without with filter with filter element element pressurisation valve 6
TP90 - R TP90 F TP90 C 6 Ø 9 6 Ø 9 6 Ø 9 L L 46 9 64 5 44 Ø 44 Ø 7 Ø 7 Ø 5 Ø 44 Ø 58 Ø 7 Ø 7 Ø 60 Ø 6 M5 M5 4 5 6 7 TP90 Example: TP90 0 0 5 P0 - Connection to reservoir 5 - Variantes Flange with bayonet connection 0 Standard C F R - Filter element - Seal Weld riser (M5X version only) Flange with threaded M5x connection Spigot Ø 60 (DIN 4557) Flange with M5X threaded connection 0 filter (lank filler cap) 0 µm - Impregnated paper 0 0 µm - Polyurethane 4 - Valves NR 0. bar pressurisation valve 0.7 bar pressurisation valve L C D E F G With Chain external for connection With Chain internal for connection C-F-R (with basket only) With Padlock tab and chain external for connection With Padlock tab and chain internal for connection C-F-R (with basket only) Dipstick and chain external (only connection ) Dipstick and Padlock tab Dipstick, Padlock tab and chain external (only connection ) 6 - asket (Stainless steel basket on request) L= 0 mm L= 50 mm In the version with chain the L= 0 basket features a press fitting. 7 - Options With Padlock tab With Dipstick P0 MP Filtri standard 7
Series TP 4 Nylon oil filler and air 6 5 4 Example TP4 Length Example TP4 Length TP4 (Materials) - Cover: Nylon - Filter element: Impregnated paper - Flange: Nylon 4 - Seal: NR 5 - Screws: Galvanised Steel 6 - asket: Nylon TP 4 Length 4 56 68 Flow rates with Δp: 0,0 bar Length Filtration l/min 0 µm 450 Length Filtration l/min 4 0 µm 600 Ø 40 Reservoir holes Ø 7 Ø 5 TP 4 : 0,85 Kg TP 4 : 0,00 Kg Ø 4 M5 8
Spare parts TP 4 spare parts Item. Description Complete filler cap Filter Element Seal Q.ty series TP 4 See order table See order table NR FPM 00606 006 4 5 TP4 Example: TP4 L0 P0 Filter element 4 Example: TP4 L0 P0 - Length - Seal NR - Filter element L0 0 µm - Impregnated paper 4 - asket L= 4 mm 5 - Options P0 MP Filtri standard 9
Series TP 5 Nylon oil filler and air Clogging indicator option 4 Example TP5 Length Without indicator Visual indicator 44 55 9 Example TP5 Length With indicator Ø 6 Ø 6 44 5 TP5 (Materials) -Cover/Flange: Nylon - Filter element: Microfibre Impregnated paper - Seals: NR FPM 4 - Screws: Galvanised Steel 5 - asket: Galvanised Steel/Nylon Clogging indicator Set pressure: - 0,06 bar ± 0 % Manual reset 80 55 Flow rates with Δp: 0,0 bar Length Filtration l/min µm 600 0 µm 000 Length Filtration l/min µm 50 0 µm 50 TP 5 : 0,460 Kg TP 5 : 0,585 Kg Reservoir holes 08 08 Ø 7 Ø 5 Ø 44 Ø 7 Ø 44 Ø 7 M5 0
Spare parts a TP 5 spare parts Item. Description Q.ty series TP 5 d Complete filler cap Filter Element See order table See order tablee b Indicator kit NR FPM 000587 000588 c a b Visual indicator Seal S6P0 O-R 06 Ø 6,64 X,6 c d Indicator securing screw O-R indicator 00670 O-R Ø 8, x,78 Changing the filter element in TP 5 series filler caps Thoroughly clean the filler cap and adjacent parts. Unscrew and raise the cover. Replace the filter element. 4 Screw the cover. 4 5 6 7 TP5 Example: TP5 F 0 P0 Filter element 7 5 Example: TP5 0 P0 - Length 4 - Seal 6 - Clogging indicator NR Without V FPM Clogging indicator - Connection 5 - asket 7 - Options F Flange P0 MP Filtri standard - Filter element L= 0 mm 0 L0 µm - Microfibre 0 µm - Impregnated paper
Series TLP 4 Nylon oil filler and air breather filler cap with electrical level indicator TLP 4 (Materials) - Cover: Nylon - Filter element: Resin impregnated cellulose - Flange: Nylon 4 - asket: Zinc Planted Steel 5 - Screws: Zinc Planted Steel 6 - Seals: NR - FPM 7 - Level indicator Level sensor (Materials) Flange: Nylon Stem: ISI 04 Float: Nylon General data Temperature From -5 C to +80 C TLP 4: 650 gr Compatibility Mineral/Sintetic oil Flow rates with Δp: 0,0 bar Filtration l/min 0 µm 450 7 Connector EN 750-80 /ISO 4400 NC C N 5 6 4 Contact SPDT Protection degree: IP 65 Max switchable capacity: 80 W (50 W SPDT) Max switchable current: Max switchable voltage: 50 Vac (0 W SPDT) Density of fluid: >0,75 Contact Ground of level indicator is not connected
Change level sensor length ON C D C D 45 Reservoir holes Ø 50 Ø 7 Ø 5 Ø 4 M5 TLP 4 Length filler cap TLP4 L 0xP0 TLP4 L 0xP0 TLP4 L 0xP0 TLP4 L 0xP0 TLP4 L 0xP0 TLP4 L 0xP0 mm 4 4 56 56 68 68 mm 97 97 4 4 C mm 90 58 75 50 6 49 D mm 0 50 0 50 0 50 ) To screw out the nut ) To extract the float C) To shorten the rod D) To re-assemble 4 5 6 TLP Example: TLP 4 L0 P0 Filter element 6 Example: TLP 4 L0 P0 - Size - Filter element 5 - asket - Level 4 L0 0 µm - Impregnated paper With electric level indicator and basket L= 00 mm - Length 4 - Seal V NR FPM 6 - Option P0 With electric level indicator and basket L= 50 mm MP filtri standard
Series SMF Nylon angled flange SMF (Materials) - Flange: Nylon - Seals: NR Cork gasket - Screws: Galvanised/Phosphated Steel SMF: 0,5 kg 7 Reservoir holes 7 M6 /4 UNC 48 8 8 48 9 5 5 0 7,5 76 89 5 5 7,5 SMF Example: SMF M P0 - Connection to reservoir - Options M Fixing with Metric screws P0 MP Filtri standard U Fixing with UNC screws - Seal NR Cork gasket 4
Metal oil filler and air Series TF 80 8 Max for strainer Ø 50 L= 80 86 40 7 Flow rate with Δp: 0,0 bar Filtration l/min µm 450 0 µm 550 TF 80: 0,655 Kg For tank hole see SMF page 8. 4 5 6 7 8 TF80 Example: TF80 0 L M P0 - connection 5 - Variants Flange with bayonet connection 0 Standard - Filter element 0 filter (lank filler cap) L 6 - asket With Padlock tab - Seal 0 µm - Impregnated paper 0 0 µm - Polyurethane L= 80 mm 7 - Connection to reservoir NR M Fixing with Metric screws Cork gasket U Fixing with UNC screws 4 - Pressurisation valve 8 - Options P0 MP Filtri standard 0, bar pressurisation valve 0,7 bar pressurisation valve nti-splash feature 9 (only with filter element µm) Only with seal NR 5
Series TF 90 Nylon oil filler and air TF 90 - R - F TF 90... C 40 Flow rate with Δp: 0,0 bar Filtration l/min µm 450 0 µm 550 TF 90: 0,55 Kg Type TF90 - R TF90 F 40 48 6 09 For tank hole see SMF page 8. C 86 78 4 5 6 7 8 TF90 Example: TF90 0 L M P0 - connection F R - Filter element - Seal Flange with bayonet connection Flange with threaded M5x connection Spigot Ø 60 (DIN 4557) Flange with threaded connection M5x 0 filter (lank filler cap) 0 µm - Impregnated paper 0 0 µm - Polyurethane NR 4 - Pressurisation valve 5 - Variants 0 Standard L C D 6 - asket With Padlock tab With Dipstick With Chain external for connection With Chain internal for connection F-R (with basket only) With Padlock tab and chain external for connection With Padlock tab and chain internal for connection F-R (with basket only) L= 0 mm 7 - Connection to reservoir 0, bar pressurisation valve 0,7 bar pressurisation valve M U 8 - Options Fixing with Metric screws Fixing with UNC screws 6 P0 MP Filtri standard
Nylon oil filler and air Series TF 5 TF 5 F TF 5 - Impregnated paper - Polyurethane 6 - Microfibre 40 Flow rate with Δp: 0,0 bar Length Filtration l/min µm 600 0 µm 000 TF 5 : 0,785 Kg Length Filtration l/min µm 50 0 µm 50 TF 5 : 0,90 Kg Length 45 87 For tank hole see SMF page 8. 6 66 4 5 6 7 8 TF5 Example: TF5 F 0 M P0 - length - Connection F Flange - Filter element 0 µm - Microfibre L0 0 µm - Impregnated paper 4 - Seal NR V FPM 5 - asket L= 0 mm 6 - Clogging indicator Without Clogging indicator 7 - Connection to reservoir M Fixing with Metric screws U Fixing with UNC screws 8 - Options P0 MP Filtri standard 7
Series SML luminium angled flange SML (Materials) - Flange: luminium - Screws: Phosphated Steel - Seals: NR Cork gasket SML: 0,80 Kg 98 5 5 60 90 40 4 M6 80 98 8 77 /4 UNC SML Example: SML M P0 - Connection to reservoir - Options M Fixing with Metric screws P0 MP Filtri standard U Fixing with UNC screws - Seal NR Cork gasket 8
Metal oil filler and air Series TL 80 79 7 4 4 Max for strainer Ø 50 L= 50 Flow rate with Δp: 0,0 bar Filtration l/min µm 450 0 µm 550 For tank hole see SML page. TL 80 : 0,70 Kg 4 5 6 7 8 TL80 Example: TL80 0 L M P0 - connection 5 - Variants Flange with bayonet connection 0 Standard - Filter element 0 filter (lank filler cap) L 6 - asket With Padlock tab - Seal 0 µm - Impregnated paper 0 0 µm - Polyurethane L= 80 mm 7 - Connection to reservoir NR M Fixing with Metric screws Cork gasket U Fixing with UNC screws 4 - Pressurisation valve 8 - Options P0 MP Filtri standard 0, bar pressurisation valve 0,7 bar pressurisation valve 9 nti-splash feature (only with filter element µm) Only with seal NR 9
Series TL 90 Nylon oil filler and air TL 90 - R - F TL 90... C 4 Flow rate with Δp: 0,0 bar Filtration l/min µm 450 0 µm 550 TL 90: 0,560 Kg Type TL90 - R TL90 F 48 56 05 For tank hole see SMF page 8. C 79 7 4 5 6 7 8 TL90 Example: TL90 0 L M P0 - Connection F R - Filter element - Seal Flange with bayonet connection Flange with threaded connection M5x Spigot Ø 60 (DIN 4557) Flange with threaded connection M5x 0 filter (lank filler cap) 0 µm - Impregnated paper 0 0 µm - Polyurethane NR 4 - Pressurisation valve 0 0, bar pressurisation valve 0,7 bar pressurisation valve 5 - Variants 0 Standard L C D 6 - asket 8 - Options With Padlock tab With Chain external for connection With Chain internal for connection F-R (with basket only) With Padlock tab and chain external for connection With Padlock tab and chain internal for connection F-R (with basket only) L= 0 mm 7 - Connection to reservoir M U P0 Fixing with Metric screws Fixing with UNC screws MP Filtri standard
Nylon oil filler and air Series TL 5 TL 5 F TL 5 4 4 Flow rate with Δp: 0,0 bar Length Filtration l/min µm 600 0 µm 000 TL 5 : 0,840 Kg Length Filtration l/min µm 50 0 µm 50 TL 5 : 0,965 Kg Length For tank hole see SML page. 4 87 09 57 4 5 6 7 8 TL5 Example: TL5 F 0 M P0 - length - Connection F Flange - Filter element 0 µm - Microfibre L0 0 µm - Impregnated paper 4 - Seal NR V FPM 5 - asket L= 0 mm 6 - Clogging indicator Without Clogging indicator 7 - Connection to reservoir M Fixing with Metric screws U Fixing with UNC screws 8 - Options P0 MP Filtri standard
Series TS Universal adapter for filling to reservoir Possible use with oil filter/air type: - T 80 - TP 90 - TP 5 - SCS 00 F dapter for Filler and breather plugs Ø 90 Ø 4 Oil filling 67 78 4 Ø 7 ir inlet/outlet TS (Materials) - dapter: nodised luminium Reservoir holes - Screws: Steel - Seals: NR FPM Cork Gasket M5 TS: Kg Ø 50 Ø 7 Connection G G G /4 SE G /4 /6 UN dapter for filler caps TS Example: TS G P0 - Connection G G /4 - Options P0 MP Filtri standard G SE 0 ( /6 UN) - Seal V NR Cork gasket FPM