T GLY EOENDED TT TE NTTON E ED TOG EFOE NTLLNG DOO. ETTLE EEN DOO EPE DOLE DOO installation instructions NTLLTON TOOL Phillips crewdriver measuring tape and-eld or Power aw power drill & its se saw blade suitable for cutting aluminum. ntroduction The Larson EPE retractable screen features a fully assembled screen cassette pre-sized for opening sizes indicated on the packaging box. f the door opening is shorter than this product, contact Larson for help with another product. The instructions are split into two sections: ecess nstallation, Page 2, and urface nstallation, PGE 9. Determine which you need before starting. Please contact your Larson Dealer for additional custom sizes and colors. Larson EPE 200 nstructions part number : 202220703.03.13.13
escape 200 EE NTLLTON PGE 2 PLL Optional ottom lide olt T J J PLL Optional Top lide olt K P K G K K F E PT DEGNTON F creen assette ssembly oot ody End ap Top etainer Guide (can be E F G ottom Guide ail Top Guide ail Threshold Transition Threshold Transition End aps andle oot ody J #6 x 3/4 (19mm) Phillips Flathead ountersunk crews for oot ody End aps K ecess ount lips #8 x 3/4 (19mm) Phillips Panhead crews P Pile Weather trip T installed on outer or inner door.) ubber umpers lide olt ottom lide olt etainer Top lide olt etainer #4 x 3/8 (9.5mm) Phillips Panhead crews
EPE 200 installation instructions PGE 3 EE NTLLTON 1 inside ounting The -creen assette will be mounted using K-ecess ounting lips the door frame. 1- ecess nstallation K Double creen K 2 width easuring easure the opening width and height in several places and record the smallest and height measurement. ecess nstallation ecord W
EPE 200 installation instructions PGE 4 EE NTLLTON 3.1 3 The creen assette The -creen assette ssembly can be installed on either the right or left side of the door jamb by flipping the creen assette (the rounded side of the creen assette should face outward). Determine which will be the top of the -oot ody [3.1] and attach the -oot ody End ap on the desired top end using three (3) J-#6 x ¾ (19mm) Phillips Flathead ountersunk crews. lide the -oot ody onto what will be the top end of both -creen assettes [3.2]. 3.2 nstall the -Top etainer Guide [3.3] by sliding it onto the top of both Pull ars (interior side). For now move the -Top etainer Guide down about 6. t will be further adjusted in step 12. 3.3
EPE 200 installation instructions PGE 5 EE NTLLTON TOP 4.1 PLL 4 optional NTLLNG TE LDE OLT EOY LOK dentify which of the two screen panels will be the one most often used to enter and exit the home. You will install the lide olt ccessory Lock on the interior side of this inactive panel (the side less used). On the inactive panel loosen the llen head set screw on the -Top etainer Guide. lide to remove the -Top etainer Guide from the interior side of the pull bar and then reinstall it in the same groove but on the opposite side of the pull bar (the exterior side). For now, slide the -Top etainer Guide down PLL about 4 so it is out of the way until it is adjusted and tightened in the final step. OTTO n this same interior groove of the pull bar, slide in an -lide olt at the bottom and then another at the top. ake certain that the pointed end of each lide olt faces out [4.1]. 5.1 K-lips for ecess nstall 5 nstalling the assette sing the -#8 x 3/4 (19mm) Phillips Panhead crews, install the K-ecess ounting lips 16 from the top and bottom of the door opening [5.1]. Lock one -creen assette onto the mounting clips [5.2]. The other -creen assette will be installed in tep 8. 5.2 ecess nstallation nsert into clip flange here. nap into clip notch here. assette EW FO OE 6 ut the Top and ottom ails sing the measurements from tep 2, ubtract 5 (127mm) from the top guide ubtract 4-3/8 (111mm) from the bottom guide ut the rails to size.
EPE 200 installation instructions PGE 6 EE NTLLTON 7 crimp weather strips rimp in the upraised channel lip on the inside of each corner of the -Top Guide ail and -ottom Guide ail to keep the P-Pile/Weather trip from moving, as shown at left. 8.1 8 nstalling the Top and ottom Guide ails lide the -ottom Guide ail fully onto the tab on the -creen assette End ap [8.1] that was installed on the door frame in tep 5. 8.2 lide the -oot ody upward on this creen assette until it rests snug with the top of the door opening [8.2]. lide the -ottom Guide ail fully onto the -creen assette End ap [8.1] of the second cassette that is yet to be installed within the door frame. Position the -Top Guide ail so that it rests on the Pull ar of the -creen assette ssembly that has already been installed. Position and rest the opposite end of the -Top Guide ail on the pull bar of the second -creen asette ssembly. ove the second -creen assette into the door frame and lock the second -creen assette onto the K-ounting lips [5.2]. lide the -oot ody upward on the second -creen assette until it rest snug with the top of the door opening. Position the -Top Guide ail onto the tab of the -oot ody [8.3]. 8.3
EPE 200 installation instructions PGE 7 EE NTLLTON 9.4 F E Profiles of ottom Guide ail and Threshold Transition 9 optional threshold transition for recess mount only efore screwing down the -ottom Guide ail, you may choose to install the E-Threshold Transition (with F-Threshold Transition End aps) 9.4]. This part is optional; it protects the bottom guide rail and it is also a nice aesthetic feature. The Transition may be installed toward the interior or exterior of the home. To install, cut the Transition to the door opening width, less 6-1/4 (159mm) for Double Door creens. nsert the F-Threshold Transition End aps, slide the lip of the Transition under the ottom Guide ail and secure both profiles with four (4) -#8 x 3/4 (19mm) Phillips Panhead crews. Position screws 6 inches in from each end and center the middle one. 10 ecure The ails With crews ecure the -ottom Guide ail and -Top Guide ail with four -#8 x 3/4 (19mm) Phillips Panhead crews each. Position screws 6 inches (150mm) in from each end and equally space the remaining screws. When installing the ottom and Top Guide ail, use the convenient Pile Opener included with this kit, to temporarily separate the two insect piles. This will make for easier viewing and installation of the screws. Pile Opener
EPE 200 installation instructions PGE 8 EE NTLLTON PLL 11.1 11 OPTONL NTLLNG LDE OLT ETNE (PPLLE ONLY F TEP FO W PLEENTED) lose the screen doors. Now, on the -ottom Guide ail and the -Top Guide ail, make pencil marks to the center of the channel in which you ve installed the lide olts. enter the T-ottom lide olt etainer to your channel mark, with the bottom of the etainer flush to the bottom of the -ottom Guide ail. T Pencil mark the position for the screws, set the etainer aside, and drill 1/8 holes. Then attach the T-ottom lide olt etainer using (2) - #4 x 3/8 Phillips Panhead crews [10.1]. 11.2 Position the -Top lide olt etainer so that it also centers to the channel mark, with the bottom of the etainer flush with the bottom of the -Top Guide ail. Pencil mark the position for the 4 screws, set aside the etainer and drill 1/8 holes. ttach the -Top lide olt etainer using (4) - #4 x 3/8 Phillips Panhead crews [10.2]. PLL 12 djusting the Top ETNE GDE & andles djust the -Top etainer Guide(s) so that they are positioned at the top of the Pull ar(s) approximately 1/8 (3mm) below the top guide rail. Tighten llen-ead et crew. djust the G-andle heights by loosening the llen-ead et crew, move the G-andle as desired and retighten screw. Note: the etainer Guide(s) should NOT touch the Top Guide ail when positioned correctly.
escape 200 FE NTLLTON PGE 9 O J J O O O PLL P L Optional Top lide olt PLL L G L T Optional ottom lide olt L N N PT DEGNTON N creen assette ssembly L urface ount lips Top etainer Guide (can be G J ottom Guide ail Top Guide ail andle oot ody oot ody End ap #6 x 3/4 (19mm) Phillips Flathead ountersunk crews for oot ody End ap #8 x 3/4 (19mm) Phillips Panhead crews N 1/8 (3mm) x 1-3/4 (44mm)urface ount crews for ottom Guide ail O urface ount crew over aps for Top ail P Pile Weather trip T installed on outer or inner side.) ubber umpers lide olt ottom lide olt etainer Top lide olt etainer #4 x 3/8 (9.5mm) Phillips Panhead crews
EPE 200 installation instructions PGE 10 FE NTLLTON 1 ounting urface / Flush ount the -creen assette using L-urface ounting lips. urface nstallation Door L Jamb L rickmold 2 easuring Place a small mark on the frame to indicate the outside alignment location where you wish to position the screen. easure the opening width and height in several places and record the smallest width and height measurement. ecord W Width (W) ead eight () ill
EPE 200 installation instructions PGE 11 FE NTLLTON 3.1 3 The creen assette The -creen assette ssembly can be installed on either the right or left side of the door jamb by flipping the creen assette (the rounded side of the creen assette should face outward). Determine which will be the top of the -oot ody [3.1] and attach the -oot ody End ap on the desired top end using three (3) J-#6 x ¾ (19mm) Phillips Flathead ountersunk crews. 3.2 lide the -oot ody onto what will be the top end of both -creen assette ssemblies [3.2]. nstall the -Top etainer Guide [3.3] by sliding it onto the top of both Pull ars (interior side). For now move the -Top etainer Guide down about 6. t will be further adjusted in step 11. 3.3 TOP 4.1 PLL 4 optional NTLLNG TE LDE OLT EOY LOK dentify which of the two screen panels will be the one most often used to enter and exit the home. You will install the lide olt ccessory Lock on the interior side of this inactive panel (the side less used). On the inactive panel loosen the llen head set screw on the -Top etainer Guide. lide to remove the -Top etainer Guide from the interior side of the pull bar and then reinstall it in the same groove but on the opposite side of the pull bar (the exterior side). For now, slide the -Top etainer Guide down PLL about 4 so it is out of the way until it is adjusted and tightened in the final step. OTTO n this same interior groove of the pull bar, slide in an -lide olt at the bottom and then another at the top. ake certain that the pointed end of each lide olt faces out [4.1].
EPE 200 installation instructions PGE 12 FE NTLLTON 5.1 L-lips for urface nstall 5 nstalling the assette emove and discard the P-Pile/Weather trip from the back of -creen assette. lide two L-urface ount lips into the groove on the rear of both creen assettes [5.1]. Position one of the -creen assettes, and use -#8 x 3/4 (19mm) Phillips Panhead crews to secure L-urface ount lips to the opening [5.2]. The other -creen asette will be installed in tep 8. 5.2 urface nstallation 6 ut the Top and ottom ails sing the measurements from tep 2, ubtract 5 (127mm) from the top guide ubtract 4-3/8 (111mm) from the bottom guide ut the rails to size. 7 crimp weather strips rimp in the upraised channel lip on the inside of each corner of the -Top Guide ail and -ottom Guide ail to keep the P-Pile/Weather trip from moving, as shown at left.
EPE 200 installation instructions PGE 13 FE NTLLTON 8.1 8 nstalling the Top and ottom Guide ails lide the -ottom Guide ail fully onto the tab on the -creen assette End ap [8.1] that was installed on the door frame in tep 5. NOTE: The ottom and Top ails each have decorative grooves on one side. This groove should face the outside [8.2]. lide the -oot ody upward on the -creen assette until it aligns with the desired alignment mark that you made on the frame [8.3]. Position the -Top Guide ail so that it rests on the Pull ar of the -creen assette ssembly that has already been installed. Position and rest the opposite end of the -Top Guide ail on the pull bar of the second -creen asette ssembly. ove the second -creen assette to the door frame and fasten the cassette to the frame using the L-urface ount lips and the -#8 x 3/4 (19mm) Phillips Panhead crews [5.2]. 8.2 lide the -Top Guide ail onto the tab of the -oot ody [8.4]. 8.3 8.4 DEOTE GOOE N O O N O N N O 9 ecure The ails With crews lign the outside edge of both the -ottom Guide ail and -Top Guide ail with the alignment mark on the door frame. -Top Guide ail: Drill four (4) 3/8 (9.5mm) holes evenly spaced through the outside face only of the front surface of the -Top Guide ail. sing these larger holes as a guide, center and drill 1/8 (3mm) through the rear side of the rail. sing the larger 3/8 (9.5mm) holes for access, insert -#8 x 3/4 (19mm) Phillips Panhead crews into the 1/8 (3mm) holes to secure the Top Guide ail to the frame. omplete the installation by inserting O-over aps into the access holes. -ottom Guide ail: sing the Decorative Trim Groove [8.2] as a guide (staying underneath the glide platforms inside the ottom Guide ail), drill four (4) 1/8 (3mm) holes evenly spaced and through both sides of the -ottom Guide ail. ecure the rails to the frame using N-1/8 (3mm) x 1-3/4 (44mm) urface ount crews. Do not over tighten.
EPE 200 installation instructions PGE 14 FE NTLLTON PLL 10.1 10 OPTONL NTLLNG LDE OLT ETNE (PPLLE ONLY F TEP FO W PLEENTED) lose the screen doors. Now, on the -ottom Guide ail and the -Top Guide ail, make pencil marks to the center of the channel in which you ve installed the lide olts. enter the T-ottom lide olt etainer to your channel mark, with the bottom of the etainer flush to the bottom of the -ottom Guide ail. Pencil T mark the position for the screws, set the etainer aside, and drill 1/8 holes. Then attach the T-ottom lide olt etainer using (2) - #4 x 3/8 Phillips Panhead crews [10.1]. 10.2 Position the -Top lide olt etainer so that it also centers to the channel mark, with the bottom of the etainer flush with the bottom of the -Top Guide ail. Pencil mark the position for the 4 screws, set aside the etainer and drill 1/8 holes. ttach the -Top lide olt etainer using (4) - #4 x 3/8 Phillips Panhead crews [10.2]. PLL 11 djusting the Top ETNE GDE & andles djust the -Top etainer Guide(s) so that they are positioned at the top of the Pull ar(s) approximately 1/8 (3mm) below the top guide rail. Tighten llen-ead et crew. djust the G-andle heights by loosening the llen-ead et crew, move the G-andle as desired and retighten screw. Note: the etainer Guide(s) should NOT touch the Top Guide ail when positioned correctly.
EPE 200 installation instructions PGE 15? nstallation uestions? issing Parts? eplacement Parts? DON T GO K TO TE TOE! Troubleshooting Guide TE DOO OTTO TEOLD LOPE TEEPLY: The ottom Guide will not work properly installed at an angle. se wedge shims to adjust the ottom Guide until level. EEN TON O DGED: eplace the mesh using a creen efill Kit. TE LONG GNET DO NOT FLLY EL O TE EEN DOE NOT LOE EENLY: lean the agnets using mild soap and water. clean any debris from inside the ottom Guide. Debris can interfere with closing and smooth screen operation. open the screen and check that the magnet that is located in the Pull ar aligns with the magnetic strip in the D-Dual-ount ide ail with agnet. To alter the alignment remove the -#8 x 3/4 (19mm) Phillips Panhead crews for the center of the D-Dual-ount ide ail. Flex the center of the D-Dual-ount ide ail 1/8" - 3/16" (3mm-4mm) toward the outside and then reinstall the -#8 x 3/4 (19mm) Phillips Panhead crews. EOD YO PODT EGTTON NE EE: