Heavy Duty Vertical Machining Center

Heavy Duty Vertical Machining Center

Heavy Duty Vertical Machining Center High Productivity Large Capacity Easy Operation The Mynx series is designed to offer exceptionally high rigidity and powerful spindles that form the support for heavy-duty machining to satisfy our customers' demands for high productivity. 02 Heavy Duty Vertical Machining Center

Heavy Duty Vertical Machining Center Improved features found on the Mynx series include a wide selection of spindles, an increased tool-storage capacity on a cam-type tool changer, an extended Y stroke, an easy operation software package, and more compared to the previous models. Together they enable maximum machining capability and ease of operation for a spectrum of machining operations. 03

High Rigidity The highly-rigid body found on the Mynx series enables exceptionally heavy-duty machining. The highly-rigid body structure is obtained by using the latest FEM analysis method, which optimizes the static and dynamic stiffness characteristics of the Mynx series. The resulting arch-shaped body structure provides an unrivalled level of rigidity, enabling an unsurpassed performance in heavyduty machining. Arch-shaped body Static stiffness The highly rigid body raises the static stiffness by 30% compared to the previous model. Dynamic stiffness Dynamic stiffness of the X, Y, and Z axes is significantly improved. High-frequency response is increased by 30% when compared to previous models. Finite Element Method (FEM) analysis is used to design an exceptionally stable body. 04 Heavy Duty Vertical Machining Center

Broader box guideways Compared to the previous models, the broader box guideways greatly improve the machine's dynamic characteristics. Extension of the Y-axis stroke The extended Y-axis stroke allows wider work area compard to the previous model. Wider than previous Model Mynx 5400 : 540 (21.3) Mynx 6500 : 670 (26.4) Mynx 7500 : 762 (30.0) Y-axis Z-axis Mynx 5400 : 530 (20.9) Mynx 6500 : 625 (24.6) Mynx 7500 : 625 (24.6) Improves the machining durability of the Z-axis. Longer than previous Model X-axis Mynx 5400 : 1020 (40.2) Mynx 6500 : 1270 (50.0) Mynx 7500 : 1525 (60.0) Previous Model Mynx series Mynx 5400 Mynx 6500 Z-axis Span width 22% 5% Z-axis Span Length 32% 8% Mynx 540 Mynx 650 510 mm (20.1 inch) 650 mm (25.6 inch) Mynx 5400 Mynx 6500 540 mm (21.3 inch) 670 mm (26.4 inch) 30 mm UP (1.2 inch) 20 mm UP (0.8 inch) Mynx 750 762 mm (30.0 inch) Mynx 7500 762 mm (30.0 inch) Scraping of surface The sliding surface of each guideway is bonded with Rulon 142 to reduce friction, then hand scraped for a perfect fit. Rapid traverse Mynx 650 Mynx series X-axis m/min (ipm) 24 (944.9) 30 (1181.1) Y-axis m/min (ipm) 24 (944.9) 30 (1181.1) Z-axis m/min (ipm) 20 (787.4) 24 (944.9) 05

High Power A selection of powerful spindles enables the Mynx series to perform rigorous heavy-duty machining. Belt driven Std. 40 taper spindle is a true cartridge type unit supported by four precision class high speed bearings which are permanently greased and lubricated. The spindle is driven by a high torque A.C. motor delivering high power. Gear driven The two-step gearbox generates an exceptionally high torque for the broadest spectrum of heavy-duty machining. (Only for taper #50) A wide selection of spindles The Mynx series' wide selection of spindles enables customers to optimize performance for various machining operations. Model Taper Speed Power Power Max. Torque [DIN] : r/min Transmission : kw (Hp) : N.m (ft-lbs) #40 8000 std. 11/15 (14.8/20.1) [Con./30min] 191.2 (141.1) [30min] Belt-driven 12000 15.6/15.6 (20.9/20.9) [Con./30min] 165.7 (122.3) [30min] Mynx 5400 Mynx 6500 #50 std. 11/15/15 (14.8/20.1/20.1) [Con./15/30min] 286.4 (211.4) [15min] Belt-driven 6000 15/18.5 (20.1/24.8) [Con./30min] 306.9 (226.5) [30min] Gear-driven 18.5/22 (24.8/29.5) [Con./30min] 452.0 (333.6) [30min] 8000 Belt-driven 11/15/15 (14.8/20.1/20.1) [Con./15/30min] 286.4 (211.4) [15min] #40 12000 Belt-driven std. 22/26 (29.5/34.9) [Con./30min] 165.7 (122.3) [30min] Dual contact (BIG PLUS) Taper contact Flange contact Std. The Big Plus system provides simultaneous dual tool-holder contact at the tapered side and the nose face of the spindle. Mynx 7500 #50 std. 15/18.5 (20.1/24.8) [Con./30min] 306.9 (226.5) [30min] Belt-driven 6000 18.5/22 (24.8/29.5) [Con./30min] 365.5 (269.7) [30min] Gear-driven 18.5/22 (24.8/29.5) [Con./30min] 452.0 (333.6) [30min] 8000 Belt-driven 11/15/15 (14.8/20.1/20.1) [Con./15/30min] 286.4 (211.4) [15min] 06 Heavy Duty Vertical Machining Center

Spindle power-torque diagram #40 #50 8000 r/min Belt driven Mynx 5400 / 6500 Spindle motor power : 11 / 15 kw (14.8 / 20.1 Hp) 12000 r/min Belt driven Mynx 5400 / 6500 Spindle motor power : 15.6 / 15.6 kw (20.9 / 20.9 Hp) 12000 r/min Belt driven Mynx 7500 Spindle motor power : 22 / 26 kw (29.5 / 34.9 Hp) 6000 r/min Belt driven Mynx 5400 / 6500 Spindle motor power : 11 / 15 / 15 kw (14.8 / 20.1 / 20.1 Hp) Torque : N.m (ft-lbs) Power : kw (Hp) Torque : N.m (ft-lbs) Power : kw (Hp) Torque : N.m (ft-lbs) Power : kw (Hp) Torque : N.m (ft-lbs) Power : kw (Hp) 191.2 (141.1) 140.2 (103.5) 30 Minutes Continuous 15.0 (20.1) 11.0 (14.8) 9.0 (12.1) 165.7 (122.3) 140.2 (103.5) 30 Minutes Continuous 15.6 (20.9) 15.0 (20.1) 11.0 (14.8) 165.7 (122.3) 140.2 (103.5) 30 Minutes Continuous 26.0 (34.9) 22.0 (29.5) 15.0 (20.1) 11.0 (14.8) 286.4 (211.4) 190.9 (140.9) 140.0 (103.3) 95.5 (70.5) 15 Minutes 30 Minutes Continuous 15.0 (20.1) 11.0 (14.8) 7.5 (10.1) 23.5 (17.3) 17.7 (13.1) 12.7 (9.4) 10.8 (8.0) 0 750 6000 8000 Spindle Speed (r/min) 15.7 (11.6) 12.7 (9.4) 11.8 (8.7) 8.8 (6.5) 900 1064 Spindle Speed (r/min) 9491 12000 11673 37.3 (27.5) 31.4 (23.2) 11.8 (8.7) 8.8 (6.5) 0 Spindle Speed (r/min) 1500 6000 12000 0 500 750 6000 Spindle Speed (r/min) 2.4 (3.2) 1.8 (2.4) Torque : N.m (ft-lbs) 735.5 (542.8) 306.9 (226.5) 249.1 (183.8) 51.0 (37.6) 41.2 (30.4) 14.7 (10.8) 11.8 (8.7) 6000 r/min Belt driven Spindle motor power : 15 / 18.5 kw (20.1 / 24.8 Hp) 30 Minutes Continuous Power : kw (Hp) 70 (93.9) 18.5 (24.8) 15.0 (20.1) 9.0 (12.1) 7.5 (10.1) Torque : N.m (ft-lbs) 900 (664.2) 365.5 (269.7) 307.7 (227.1) 60.8 (44.9) 51.0 (37.6) 17.6 (13.0) 14.7 (10.8) 6000 r/min Belt driven Mynx 7500 Spindle motor power : 18.5 / 22 kw (24.8 / 29.5 Hp) 30 Minutes Continuous Power : kw (Hp) 70.0 (93.9) 22.0 (29.5) 18.5 (24.8) 11.0 (14.8) 9.0 (12.1) Torque : N.m (ft-lbs) 452.0 (333.6) 380.5 (280.8) 6000 r/min Gear driven Spindle motor power : 18.5 / 22 kw (24.8 / 29.5 Hp) 30 Minutes Continuous Power : kw (Hp) 22.0 (29.5) 18.5 (24.8) Torque : N.m (ft-lbs) 286.4 (211.4) 191.2 (141.1) 140.2 (103.5) 95.1 (70.2) 39.2 (28.9) 8000 r/min Belt driven Spindle motor power : 11 / 15 / 15 kw (14.8 / 20.1 / 20.1 Hp) 15 Minutes 30 Minutes Continuous Power : kw (Hp) 15.0 (20.1) 11.0 (14.8) 9.0 (12.1) 7.5 (10.1) 0 Spindle Speed (r/min) 575 3450 6000 0 Spindle Speed (r/min) 575 3450 6000 118.7 (87.6) 99.8 (73.7) 35.0 (25.8) 29.4 (21.7) 464.3 1770 6000 Spindle Speed (r/min) 23.5 (17.3) 17.6 (13.0) 12.7 (9.4) 10.8 (8.0) 0 500 750 6,000 8,000 Spindle Speed (r/min) 07

Machining Capacity The Mynx series provides high machining performance in various cutting processes. Face mill BT40 [11/15 kw (14.8 / 20.1 Hp)] ø80mm (3.15 in.) Face mill (5Z) 6.0 mm 64 mm (2.5 in.) (0.24 in.) Face mill BT50 [15/18.5 kw (20.1 / 24.8 Hp)] ø125mm (4.92 in.) Face mill (8Z) 7.0 mm 100 mm (3.9 in.) (0.28 in.) Face mill BT50 Gear-driven [18.5/22 kw (24.8 / 29.5 Hp)] ø125mm (4.92 in.) Face mill (8Z) 7.0 mm 110 mm (4.3 in.) (0.28 in.) Carbon steel (SM45C) Machining rate 422 cm 3 /min (16.6 in 3 /min) Spindle speed 750 r/min Feedrate 1100 mm/min (43.3 ipm) Carbon steel (SM45C) Machining rate 504 cm 3 /min (19.8 in 3 /min) Spindle speed 575 r/min Feedrate 720 mm/min (27.6 ipm) Carbon steel (SM45C) Machining rate 739 cm 3 /min (29.1 in 3 /min) Spindle speed 407 r/min Feedrate 960 mm/min (37.8 ipm) Drill BT40 ø50mm (1.97 in.) Drill Spindle speed 200 r/min Feedrate 42 mm/min (1.7 ipm) Tap BT40 Tool M36 x P4.0 Spindle speed 250 r/min Feedrate 1000 mm/min (39.4 ipm) Carbon steel (SM45C) Carbon steel (SM45C) 08 Heavy Duty Vertical Machining Center

Machining Accuracy The Mynx series can be equipped with features that reduce thermal deformation for enhanced machining accuracy. 90 Features provided to reduce thermal deformation 180 0 Fresh Air Heated Air Fresh air Coolant chiller Roundness 5.8 µm 270 10µm Model : Mynx 6500 Material : A7075F Tool : Endmill ø16mm (ø 0.6 in.) (4 blades) Heated air is forced from the casting and replaced by cooler fresh air. This minimizes the risk of thermal deformation, and reduces Z-axis thermal growth by 30% compared to the previous models. The coolant chiller lowers coolant temperature, helping to cool both the workpiece and tool during the machining operation. Coolant chiller Coolant tank P- R- W- Profile leveled Filter ISO 11562 (M1) Lc / Ls = 300 Lc = 0.800 mm 2.5 0.0 [µm] -2.5 Pick-up TK300 Lt = 4.80 mm Vt = 0.50 mm/s Roughness Ra 0.12 µm Spindle speed : 8000 r/min Feedrate : 1000 mm/min (39.4 ipm) Linear scale Closed loop feedback system by optical linear scales ensures supreme positioning accuracy. Available on the X, Y and Z axes. Oil cooler The oil cooler keeps the coolant at a constant temperature. The oil circulates around the spindle and bearings to minimize thermal deformation of the spindle. 09

Automatic Tool Changer Increased tool storage capacity and shorter tool change time on a cam-type tool changer provides high machining productivity. A wide selection of tool magazine Tool change time (T-T-T) Model Mynx 5400 Mynx 6500 Mynx 7500 Taper (BT/CAT/DIN) #40 #50 #40 #50 #40 #50 Std. (Tools) 30 24 30 24 30 24 Opt. (Tools) 40-40 30 40 40 Taper #40 Taper #50 Tool storage capacity Taper #40 Taper #50 1.5 s 2.5 s Previous Model 24 tools 16 tools Maximum tool size 1.3 s 2.5 s Mynx series 30 tools std., 40 tools 24 tools std., 30 tools, 40 tools W Drum type magazine with CAM Loop type magazine with CAM L Length Weight mm (inch) kg (Ib) Previous Mynx 5400 / 6500 Previous Mynx 5400 / 6500 Taper #40 250 (9.8) 300 (11.8) 8 (17.6) 8 (17.6) Taper #50 300 (11.8) 350 (13.8) 12 (26.5) 15 (33.1) 10 Heavy Duty Vertical Machining Center

Chip Disposal Chip control is important to increase productivity and to enhance the operator's working environment. The Mynx series offers many features to optimize chip disposal. Flood coolant Inner structure for effective chips and coolant flow The inner structure of the Mynx series machines is designed to lead the flow of chips and coolant into a front-mounted chip pan for effective chip disposal. Shower coolant Through spindle coolant Middle pressure 1.96 Mpa (284.2 psi) [20 bar] High pressure 6.86 Mpa (994.7 psi) [70 bar] Chip conveyor Hinge type Scraper type Drum filter type Internal screw conveyor Coolant Gun Larger Coolant Tank Capacity Increased coolant tank capacity improves the efficiency of machine operation. Previous Model Mynx 540 300 L (79.3 galon) Mynx 650 300 L (79.3 galon) Mynx 750 300 L (79.3 galon) Mynx series Mynx 5400 380 L (100.4 galon) Mynx 6500 380 L (100.4 galon) Mynx 7500 430 L (113.6 galon) 11

Easy Set-up Operating Console Std. Workpiece loading 1 1 10.4" Color TFT LCD Monitor as Standard Feature 5 6 The wide screen displays more useful infromation for the operator. Doosan's customized pages make setting up, operating, and machine condition monitoring easier. 10.4" Previous Model 8.4" 2 Pentium Board is standard. Easy retrofit of AICC or Easy Guide-i 3 Portable MPG It makes workpiece setting easier for the operator 7 4 Easier ATC operation and maintenance. Magazine : CW Accessibility 4 3 5 Magazine : CCW PCMCIA Card It gives much easier operation and maintenance for ATC. A A Unit : mm (inch) Mynx 5400 830 (32.7) Mynx 6500 895 (35.2) Mynx 7500 1077 (42.4) Mynx 5400 / 6500 6 7 Embedded Ethernet / RS-232C Swivelling Operating Console The easy-to-use operation panel can swivel 0-90 B C B C Mynx 5400 290 (11.4) Mynx 6500 224 (8.8) Mynx 7500 321 (12.6) Mynx 5400 950 (37.4) Mynx 6500 950 (37.4) Mynx 7500 1050 (41.3) 12 Heavy Duty Vertical Machining Center

Optional Equipment Various options are available to improve the machine performance for different applications. Interface for additional equipment Automatic tool measurement Example : 1 additional axis Pneumatic Hydraulic Automatic workpiece measurement Electronic Servo driven function and device Hydraulic power units can be supplied to suit different applications, including rotary tables. Example : hydraulic fixture Pneumatic Fixture check list (for hydraulic / pneumatic fixtures) Pressure source Hydraulic P/T A/B Pneumatic P/T A/B Minimum Quantity Lublication (MQL) Hydraulic Number of ports 1pair (2-PT 3/8" port) 2pair (4-PT 3/8" port) 3pair (6-PT 3/8" port) Hydraulic power unit Contact Doosan for more information Supply scope : User Doosan (Please check the below detail specification, if you want Doosan to supply.) Use Doosan standard unit 24 L/min (6.3 gal/min) / 4.9 MPa (711 psi) Special requirement L/min (gal/min) at MPa (psi) Oil skimmer Misting device 13

Easy Operation Package Doosan's easy operation software package is customized to provide fast and easy operation for tooling, workpiece and program setup. These features maximize productivity by minimizing time lost during process setup. Programming G Code List M Code List Tool Data Registry Table Operator can check the meaning of each G-code. Operator can check the meaning of each M-code. Operator can edit & check the tool number of the tool magazine pot. Pattern Cycle Calculator ENGRAVING Std. Doosan Fanuc i series 10.4" color TFT LCD Part programming storage 1280m Embedded Ethernet It is easy to make pattern cycle program by this funciton. Operator can calcute numerical formula in relation to arc and hole easily. It makes "Engraving" programming easy. 14 Heavy Duty Vertical Machining Center

Operation / Maintenance Table Moving for Setup ATC Recovery Help Sensor Status Monitor Alarm Guidance Enables quick and easy table movement to either of three positions during setup. Allows easy recovery of ATC from ATC alarm status. Solenoid valve and sensor status can be checked without the electric diagram. The alarm remedy method for selected important alarms is displayed on the screen. Easy NC Parameter Help Operation Rate Tool Load Monitor Renishaw Tool measure Work measure Operator can check some useful parameters for easy operation. Manages working and operation times for each operator. Damage to tools is minimized by monitoring the axis and spindle load during cutting operations. Tooling and the work piece measurement are operated through a conversational control screen. Some functions may be unavailable depending on machine model. Please contact Doosan for details. 15

External Dimensions Unit : mm (inch) BT50 Top View Front View Side View Table 3119 (122.8) 2444 (96.2) 675 (26.6) 742 (29.2) 1480 (58.3) 222 (8.7) TRANSFORMER COOLER 1600 (63.0) 75 (3.0) 3200 (126.0) 1600 (63.0) R760 (29.9) R389 (15.3) TSC FILTER 594 (23.4) 1312 (51.7) 608.5 (24.0) 2891.5 (113.8) [#50 / 24T] 2136 (84.1) 820 (32.3) 1316 (51.8) 510 (20.1) (X/2 STROKE) 1200 (47.2) 510 (20.1) (X/2 STROKE) 810 (31.9) 1580 (62.2) 810 (31.9) 75 (3.0) 3200 (126.0) 75 (3.0) 995 (39.2) 772 (30.4) 830 (32.7) 1306 (51.4) 1025.4 (40.4) 815 (32.1) 150 (5.9) 530 (20.9) (Z STROKE) 270 (10.6) (Y/2 STROKE) 270 (10.6) (Y/2 STROKE) 505 (19.9) 825 (32.5) 760 (29.9) 132 (5.2) 190 (7.5) 2222 (87.5) 119.5 (4.7) 543 (21.4) 1480 (58.3) 247 (9.7) 2270 (89.4) 355 2744.5 (108.1) (14.0) 2896.5 (114.0) [#50 / 24T] 600 (23.6) 600 (23.6) 32 (1.3) 1200 (47.2) 18H8 (0.7) T-slot section 12 (0.5) 82.5 (3.2) 125 (4.9) 82.5 (3.2) 125 (4.9) 125 (4.9) 60 (2.4) 540 (21.3) 8 (0.3) Top View Front View Side View Table 3339 (131.5) 665 (26.2) 2674 (105.3) 222 (8.7) 1700 (66.9) 752 (29.6) TRANSFORMER COOLER 1600 (63.0) 1600 (63.0) 75 (3.0) 3200 (126.0) R760 (29.9) R389 (15.3) TSC FILTER 594 (23.4) 1312 (51.7) 2986.5 (117.6) [#50 / 24T] 2136 (84.1) 703.5 (27.7) 820 (32.3) 1316 (51.8) 635 (25.0) (X/2 STROKE) 1400 (55.1) 635 (25.0) (X/2 STROKE) 810 (31.9) 1580 (62.2) 810 (31.9) 75 (3.0) 3200 (126.0) 75 (3.0) 995 (39.2) 772 (30.4) 830 (32.7) 1306 (51.4) 1026 (40.4) 815 (32.1) 150 (5.9) 625 (24.6) (Z STROKE) 495 (19.5) 335 (13.2) 335 (13.2) (Y/2 STROKE) (Y/2 STROKE) 600 (23.6) 435 (17.1) 190 (7.5) 2452 (96.5) 810 (31.9) 543 (21.4) 1480 (58.3) 447 (17.6) 2470 (97.2) 270 2897 (114.1) (10.6) 2991.5 (117.8) [#50 / 24T] 112 (4.4) 157 (6.2) 700 (27.6) 700 (27.6) 1400 (55.1) 32 (1.3) 18H8 (0.7) T-slot section 12 (0.5) 85 (3.4) 125 (4.9) 125 (4.9) 125 (4.9) 125 (4.9) 85 (3.4) 10 (0.4) 670 (26.4) 60 (2.4) 16 Heavy Duty Vertical Machining Center

External Dimensions Unit : mm (inch) BT50 HIGH TSC(70BAR) 708 (27.9) OIL COOLER Top View Front View Side View Table 200 (7.9) 880 (34.7) 2142 (84.3) 75 (3.0) Tool Shank BT40 Tool Unit : mm R760 (29.9) 1950 (76.8) 1950 (76.8) 16.6 TAPER GAGE LINE 10 7/24 TAPER M16 x P2.0 TSC FILTER 594 (23.4) 880 (34.7) 75 (3.0) 1312 (51.7) 3095.5 (121.9) [#50 / 24T] 900 (35.4) 1360 (53.5) 745 (29.3) 762.5 (30.0) 1600 (63.0) 762.5 (30.0) (X/2 STROKE) (X/2 STROKE) 1065 (41.9) 1770 (69.7) (DOOR OPEN) 1065 (41.9) 75 (3.0) 3900 (153.5) 75 (3.0) 880 (34.7) 1363 (53.7) 484 (19.1) 664 (26.1) 387.8 (15.3) 625 (24.6) 150 (5.9) 381 (15.0) 750 (29.5) 381 (15.0) (Y/2 STROKE) (Y/2 STROKE) 3022 (119.0) TRANSFORMER (ETRNF050000) 297 (11.7) 0.4 0.3 550 (21.7) 1500.5 (59.1) 721.5 (28.4) 223 (8.8) 2995 (117.9) 3088.5 (121.6) [#50 / 24T] 375 (14.8) 375 (14.8) TAPER GAGE LINE 7/24 TAPER "T" 800 (31.5) 800 (31.5) 1600 (63.0) CAT40 Tool Unit : inch DIN40 Tool Unit : mm BT50 Tool Unit : mm CAT50 Tool Unit : inch DIN50 Tool Unit : mm 0.43 60 7/24 TAPER TAP "T" 15.9 3.2 35 60 ø7 68.4 15 7 23.2 ø69.9 7/24 TAPER M24 x 3 TAP 32 (1.3) 0.5 (0.02) 18H8 (0.7) 17 (0.7) 30 (1.2) T-slot section ø42 (1.7)H7 12 (0.5) ø7(gage PIN) 60 3.2 62.5 (2.5) 125 (4.9) 125 (4.9) 125 (4.9) 125 (4.9) 125 (4.9) 62.5 (2.5) 5 (0.2) 750 (29.5) 860 (33.9) 105 (4.1) ø63 ø53 60 L 2 ø44.45 65.4 ø17 2.85 ø2.5 ø2.21 ø0.28 (GAGE PIN) 0.63 0.13 1.75 GAGE PIN 2.69 ø0.67h7 ø72.3 ø50 ø63.55 11.1 18.5 ø17 ø44.45 M16 x P2.0 7/24 TAPER TAPER GAGE LINE ø100 ø85 ød D 100 100 L 35 45 31 60 GAGE LINE L 101.8 3 45 ø25h8 ø27 (ø40.1) 60 13 ø3.9 ø3.6 ø2.8 ø2.8 60 0.6 0.13 1.5 4 ø1 ø107.25 ø97.5 ø91.25 ø69.85 19.1 101.75 30 16.1 1 0.63 18.5 16.1 25.7 25.7 ø80 MAX ø23 ø7 HOLE 22.6 22.6 M16 x P2.0 ø14 15 23 2 4 25 29 ø17 30 ø19 (DIN shape) THREAD "T" ø0.91 0.9 0.98 ø0.55 0.79 0.16 1.1 1.02 ø0.28 ø0.75 0.08 ø23 ø7 HOLE 25 22.8 M16 x P2.0 ø17 ø14 15 20 2 4 28 26 30 ø19 (DIN shape) M24 x 3 THREAD ø38 ø25h7 35.4 35.4 40 35 5 5 5 8 9 8 ø17 45 85 45 30 ø23 ø1.5 1.4 1.46 1.6 "T" ø1 ø0.67 45 30 1.4 0.2 0.2 1.8 ø0.91 ø36 30 37.7 35.5 ø21 25 34 ø28 MAX 17

Machine Specifications Travel Table Spindle Feedrate Automatic tool changer Features Mynx 5400 Mynx 5400/50 Mynx 6500 Mynx 6500/50 Mynx 7500 Mynx 7500/50 X-axis mm (inch) 1020 (40.2) 1270 (50.0) 1525 (60.0) Y-axis mm (inch) 540 (21.3) 670 (26.4) 762 (30.0) Z-axis mm (inch) 530 (20.9) 625 (24.6) 625 (24.6) Distance from nose to table top mm (inch) 150-680 (5.9-26.8) 200-730 (7.9-28.7) 150-775 (5.9-30.5) 200-825 (7.9-32.5) 150-775 (5.9-30.5) 200-825 (7.9-32.5) Distance from center to column mm (inch) 567 (22.3) 722 (28.4) 785 (30.9) Table size mm (inch) 1200 x 540 (47.2 x 21.3) 1400 x 670 (55.1 x 26.4) 1600 x 750 (63.0 x 29.5) Table loading capacity kg (lb) 800 (1763.7) 1000 (2204.6) 1500 (3306.9) Table surface mm (inch) 4-125 x 18H8 (4-4.9 x 0.7H8) 5-125 x 18H8 (5-4.9 x 0.7H8) 6-125 x 18H8 (6-4.9 x 0.7H8) Max. spindle speed Belt r/min 8000 {12000} 6000 {6000, 8000} 8000 {12000} 6000 {6000, 8000} 12000 6000 {6000, 8000} Gear r/min - {6000} - {6000} - {6000} Spindle Taper ISO #40 7/24 Taper ISO #50 7/24 Taper ISO #40 7/24 Taper ISO #50 7/24 Taper ISO #40 7/24 Taper ISO #50 7/24 Taper Max. Torque Belt 8000 N.m (ft-lbf) 191.2 (141.1) {286.4 (211.4)} 191.2 (141.1) {286.4 (211.4)} - {286.4 (211.4)} Belt 6000 N.m (ft-lbf) - 286.4 {306.9} - 286.4 {306.9} - 306.9 {365.5} (211.4 {226.5}) (211.4 {226.5}) (226.5 {269.7}) Gear 6000 N.m (ft-lbf) - {452.0 (333.6)} - {452.0 (333.6)} - {452.0 (333.6)} Belt 12000 N.m (ft-lbf) {165.7 (122.3)} - {165.7 (122.3)} - 165.7 (122.3) - Rapid traverse rate (X / Y / Z) m/min (ipm) 30 / 30 / 24 (1181.1 / 1181.1 / 944.9) Cutting feedrate mm/min (ipm) 12000 (4724.4) Type of tool shank BT40, CAT40, DIN40 BT50, CAT50, DIN50 BT40, CAT40, DIN40 BT50, CAT50, DIN50 BT40, CAT40, DIN40 BT50, CAT50, DIN50 Tool storage capacity ea 30 {40} 24 30 {40} 24 {30} 30 {40} 24 {40} Max. tool diameter mm (inch) 80 {76} (3.2 {3.0}) 125 (4.9) 80 {76} (3.2 {3.0}) 125 (4.9) 80 {76} (3.2 {3.0}) 125 (4.9) Max. tool diameter without adjacent tools mm (inch) 125 (4.9) 220 (8.7) 125 (4.9) 220 (8.7) 125 (4.9) 220 (8.7) Max. tool length mm (inch) 300 (11.8) 350 (13.8) 300 (11.8) 350 (13.8) 300 (11.8) 350 (13.8) Max. tool weight kg (lb) 8 (17.6) 15 (33.1) 8 (17.6) 15 (33.1) 8 (17.6) 15 (33.1) Tool change time (tool-to-tool) s 1.3 2.5 1.3 2.5 1.3 2.5 Tool change time (chip-to-chip) s 3.7 5.5 3.7 5.5 3.7 5.5 Spindle motor Belt 8000 kw (Hp) 11 / 15 {11 / 15 / 15} 11 / 15 {11 / 15 / 15} - {11 / 15 / 15} (14.8 / 20.1) {(14.8 / 20.1 / 20.1)} (14.8 / 20.1) {(14.8 / 20.1 / 20.1)} {(14.8 / 20.1 / 20.1)} Motor Belt 6000 kw (Hp) - 11 / 15 / 15 {15 / 18.5} - 11 / 15 / 15 {15 / 18.5} - 15 / 18.5 {18.5 / 22} (14.8 / 20.1 / 20.1 {20.1 / 24.8}) (14.8 / 20.1 / 20.1 {20.1 / 24.8}) (20.1 / 24.8 {24.8 / 29.5}) Gear 6000 kw (Hp) - {18.5 / 22 (24.8 / 29.5)} - {18.5 / 22 (24.8 / 29.5)} - {18.5 / 22 (24.8 / 29.5)} Belt 12000 kw (Hp) {15.6 / 15.6 (20.9 / 20.9)} - {15.6 / 15.6 (20.9 / 20.9)} - 22 / 26 (29.5 / 34.9) - Feed motor (X / Y / Z) kw (Hp) 3.0 / 3.0 / 4.0 (4.0 / 4.0 / 5.4) 4.0 / 4.0 / 7.0 (5.4 / 5.4 / 9.4) 4.0 / 4.0 / 7.0 (5.4 / 5.4 / 9.4) Electric power supply Belt 8000 kva 36.1 {36.1} 39.4 {39.4} - {42.9} (Rated capacity) Belt 6000 kva - 36.1 {41.2} - 39.4 {44.6} - 47.3 {51.8} Power source Gear 6000 kva - {47.7} - {48.4} - {51.8} Belt 12000 kva {41.7} - {45.1} - 56.9 - Compressed air supply MPa (psi) 0.54 (78.3) Tank capacity Coolant tank capacity L (gal) 380 (100.4) 380 (100.4) 430 (113.6) Lubrication tank capacity L (gal) 1.4 (0.4) 4.3 (1.14) Machine height mm (inch) 2744 (108.0) 2900 (114.2) 2897 (114.1) 2995 (117.9) 3190 (125.6) 3240 (127.6) Machine size Machine dimension (L x W) mm (inch) 2444 x 3350 (96.2 x 131.9) 2674 x 3350 (105.3 x 131.9) 3704 x 4050 (145.8 x 159.5) Machine weight kg (lb) 7000 (15432.1) 9200 (20282.2) 14000 (30864.3) The specifications and information above-mentioned may be changed without prior notice. Note : { } are optional. For more details, please contact Doosan. Standard Feature Assembly & operation tools Coolant tank & chip pan Door interlock for safety Flood coolant system Installation parts Internal screw conveyor Operator call lamp (red, yellow, green) Portable MPG Splash guard Work light X, Y, Z Absolute pulse coder Optional Feature 4th axis preparation Automatic power off Automatic tool measurement Automatic workpiece measurement Chip conveyor & chip bucket EZ Guide i Minimum Quantity Lubrication Oil cooler & spindle head cooling system Oil skimmer Shower coolant Test bar Through spindle coolant system 18 Heavy Duty Vertical Machining Center

NC Unit Specifications DOOSAN-Fanuc i series Fanuc 32i-A AXES CONTROL - Controlled axes 3 ( X,Y,Z ) - Simultaneously controllable axes Positioning (G00) / Linear interpolation (G01) : 3 axes Circular interpolation (G02, G03) : 2 axes - Backlash compensation - Emergency stop / overtravel - Follow up - Least command increment : 0.001mm / 0.0001" - Least input increment : 0.001mm / 0.0001" - Machine lock all axes / Z axis - Mirror image Reverse axis movement (setting screen and M-function) - Stored pitch error compensation Pitch error offset compensation for each axis - Stored stroke check 1 Overtraval controlled by software - Absolute pulse coder - Position switch INTERPOLATION & FEED FUNCTION - 2nd reference point return G30 - Circular interpolation G02, G03 - Cylinderical interpolation G07.1 - Dwell G04 - Exact stop check G09, G61(mode) - Feed per minute mm / min - Feedrate override (10% increments) 0-200 % - Helical interpolation - Jog override (10% increments) 0-200 % - Linear interpolation G01 - Manual handle feed Max. 3 units - Manual handle feedrate 0.1 / 0.01 / 0.001mm - Manual handle interruption - Override cancel M48 / M49 - Positioning G00 - Rapid traverse override F0 (fine feed), 25 / 50 / 100 % - Reference point return G27, G28, G29 - Skip function G31 SPINDLE & M-CODE FUNCTION - M-code function M3 digits - Spindle orientation - Spindle serial output - Spindle speed command S5 digits - Spindle speed override (10% increments) 50-150 % TOOL FUNCTION - Cutter compensation C G40, G41, G42 - Number of tool offsets 400 ea - Tool length compensation G43, G44, G49 - Tool life management - Tool number command T2 digits - Tool offset memory C Geometry / Wear and Length / Radius offset memory - Tool position offset G45 - G48 PROGRAMMING & EDITING FUNCTION - Absolute / Incremental programming G90 / G91 - Automatic Coordinate system setting - Background editing - Canned cycle G73, G74, G76, G80 - G89, G99 - Circular interpolation by radius programming - Custom macro B - Decimal point input - Extended part program editing - I / O interface RS - 232C - Inch / metric conversion G20 / G21 - Label skip - Local / Machine coordinate system G52 / G53 - Maximum commandable value ±99999.999 mm (±9999.9999 inch) - No. of Registered programs 400 ea - Optional block skip - Optional stop M01 - Part program storage 1280 m - Playback - Program number O4-digits - Program protect - Program stop / end M00 / M02, M30 - Rigid tapping G84, G74 - Sub program Up to 4 nesting - Tape code ISO / EIA Automatic discrimination - Thread cutting - Work coordinate system G54 - G59 OTHERS FUNCTIONS (Operation, setting & Display, etc) - 3rd / 4th reference return - Additional work coordinate system G54.1 P1-48 ( 48 pairs ) - AI APC(Advanced Preview Control) 20 block preview - Alarm display - Alarm history display - Automatic corner override G62 - Clock function - Coordinate rotation G68, G69 - Cycle start / Feed hold - Display of PMC alarm message Message display when PMC alarm occurred - Dry run - Embedded Ethernet - Graphic display Tool path drawing - Help function - High speed skip function - Loadmeter display - MDI / DISPLAY unit 10.4" Color LCD, keyboard for data input(small), soft-keys - Memory card interface - Operation functions Tape / Memory / MDI / Manual - Operation history display - Optional angle chamfering / corner R - Polar coordinate command G15 / G16 - Program restart - Programmable data input Tool offset and work offset are entered by G10, G11 - Programmable mirror image G50.1 / G51.1 - Run hour and part number display - Scaling G50, G51 - Search function Sequence NO. / Program NO. - Self - diagnostic function - Servo setting screen - Single block - Single direction positioning G60 - Stored stroke check 2 OPTIONAL SPECIFICATIONS - Additional controlled axes 5 axes in total - AICC (AI Contour Control) with Hardware 40 block preview - EZ Guide i (Doosan infracore Conversational Programming Solution) with 10.4" Color TFT - Dynamic graphic display (w/10.4" Color LCD) Machining profile drawing => When the EZ Guide i is used, the Dynamic graphic display cannot application - Fast Data server - Fast Ethernet - Tool load monitoring function (Doosan) AXES CONTROL - Controlled axes 3 (X, Y, Z) - Simultaneously controllable axes Positioning (G00) / Linear interpolation (G01) : 3 axes Circular interpolation (G02, G03) : 2 axes - Backlash compensation - Emergency stop / overtravel - Follow up - Least command increment 0.001 mm ( 0.0001 inch) - Least input increment 0.001 mm ( 0.0001 inch) - Machine lock All axes / Z axis - Mirror image Reverse axis movement (Setting screen and M - function) - Stored pitch error compensation Pitch error offset compensation for each axis - Stored stroke check 1 Overtravel controlled by software - Absolute pulse coder INTERPOLATION & FEED FUNCTION - 2nd reference point return G30 - Circular interpolation G02, G03 - Dwell G04 - Exact stop check G09, G61 (mode) - Feed per minute - Feedrate override (10% increments) 0-200 % - Jog override (10% increments) 0-200 % - Linear interpolation G01 - Manual handle feed 1 unit - Manual handle feedrate x1, x10, x100 (per pulse) - Override cancel M48 / M49 - Positioning G00 - Rapid traverse override F0 (fine feed), 25 / 50 / 100 % - Reference point return G27, G28, G29 - Skip function G31 - Helical interpolation - AICC I 30 block preview - Thread cutting, synchronous cutting - Program restart - Automatic corner deceleration (Specify AI Contour control II) - Feedrate clamp by circular acceleration (Specify AI Contour control II) - Linear ACC / DEC before interpolation (Specify AI Contour control II) - Linear ACC / DEC after interpolation - Rapid traverse bell-shaped acceleration/deceleration - Smooth backlash compensation SPINDLE & M-CODE FUNCTION - M-code function M3 digits - Spindle orientation - Spindle serial output - Spindle speed command S5 digits - Spindle speed override (10% increments) 10-150 % - Spindle output switching - Retraction for rigid tapping - Rigid tapping G84, G74 TOOL FUNCTION - Tool nose radius compensation G40, G41, G42 - Number of tool offsets 64 ea - Tool length compensation G43, G44, G49 - Tool number command T2 digits - Tool life management Geometry / Wear and Length / Radius offset memory - Tool offset memory C - Tool length measurement PROGRAMMING & EDITING FUNCTION - Absolute / Incremental programming G90 / G91 - Auto. Coordinate system setting - Background editing - Canned cycle G73, G74, G76, G80 - G89, G99 - Circular interpolation by radius programming - Custom macro B - Custom size 512Kb - Decimal point input - I / O interface RS - 232C - Inch / metric conversion G20 / G21 - Label skip - Local / Machine coordinate system G52 / G53 - Maximum commandable value ±99999.999 mm (±9999.9999 inch) - No. of Registered programs 500 ea - Optional stop M01 - Part program storage 640 m (2,100 ft) [256 kb] m - Program number O4-digits - Program protect - Program stop / end M00 / M02, M30 - Programmable data input Tool offset and work offset are entered by G10, G11 - Sub program Up to 4 nesting - Tape code ISO / EIA Automatic discrimination - Work coordinate system G54 - G59 - Additional work coordinate system (48 Pair) G54.1 P1-48 pairs - Coordinate system rotation G68, G69 - Extended part program editing - Optional angle chamfering / corner R - Macro executor OTHERS FUNCTIONS (Operation, Setting & Display, etc) - Alarm display - Alarm history display - Clock function - Cycle start / Feed hold - Control axis detach - Display of PMC alarm message Message display when PMC alarm occurred - Dry run - Embedded Ethernet - Graphic display Tool path drawing - Help function - Loadmeter display - MDI / DISPLAY unit 10.4" Color TFT LCD, Keyboard for data input, soft-keys - Memory card interface - Operation functions Tape / Memory / MDI / Manual - Operation history display - Program restart - Run hour and part number display - Search function Sequence NO. / Program NO. - Self - diagnostic function - Servo setting screen - Single block - External data input - Multi language display - Stored stroke check 2 OPTIONAL SPECIFICATIONS - 3-dimensional coordinate conversion - 3-dimensional tool compensation - 3rd / 4th reference return - Addition of tool pairs for tool life management 1024 pairs - Additional controlled axes Max. 5 axes in total - Additional work coordinate system G54.1 P1-300 (300 pairs ) - DSQ 1 (AICC II + Machining condition selection function) 80 block preview - DSQ 2 (AICC II + Machining condition selection function + Data server + 1GB) 80 block preview - Automatic corner override G62 - Chopping function G81.1 - Cylindrical interpolation G07.1 - Dynamic graphic display Machining profile drawing - Exponential interpolation - Interpolation type pitch error compensation - EZ Guide i (Doosan infracore Conversational Programming Solution) with 10.4" Color TFT => When the EZ Guide i is used, the Dynamic graphic display cannot application - Tape format for FS15 - Increment system 1/10 - Figure copying G72.1, G72.2 - Handle interruption - High speed skip function - Involute interpolation G02.2, G03.2 - Machining time stamp function - No. of Registered programs 1000 ea - Number of tool offsets 99 / 200 / 400 pairs - Optional block skip addition 9 blocks - Part program storage 512K / 1M / 2M byte - Playback function - Polar coordinate command G15 / G16 - Polar coordinate interpolation G12.1 / G13.1 - Programmable mirror image G50.1 / G51.1 - Single direction positioning G60 - Tool load monitoring function (Doosan) - Tool position offset G45 - G48 - Position switch *) Pre discussion required 19

Heavy Duty Vertical Machining Center http://www.doosaninfracore.com/machinetools Head Office : Doosan Tower 23rd FL., 18-12, Euljiro-6Ga, Jung-Gu, Seoul, Korea 100-730 Tel : ++82-2-3398-8693 / 8671 / 8680 Fax : ++82-2-3398-8699 Doosan Infracore America Corp.: 19 Chapin Rd. Pine Brook, NJ 07058, U.S.A. Tel : ++1-973-618-2500 Fax : ++1-973-618-2501 Doosan Infracore Germany GmbH : Hans-Böckler-Strasse 29, D-40764 Langenfeld-Fuhrkamp, Germany. Tel : ++49-2173-8509-0 Fax : ++49-2173-8509-60 Doosan Infracore Yantai Co., LTD : 13 Building, 140 Tianlin Road, Xuhui District, Shanghai, China (200233) Tel : ++86-21-6440-3384 (808, 805) Fax : ++86-21-6440-3389 i-ser EX 1102SP Design and specifications are subject to change without prior notice.