B-05X93 rev.0706
Dresser Roots, Dresser, Inc. is the longest continuously run manufacturer of rotary positive displacement blowers in the United States. In 1854, Francis and Philander Roots, woolen mill owners in Connersville, IN, stumbled upon the principles that drive the rotary positive displacement concept. Francis and Philander s attempts to improve efficiency in their mill s power system failed as the wooden lobed water wheel warped and jammed when put to use. In the course of investigating the problem on dry land, one of the brothers turned a shaft and rotated the pair of impellers. The impellers produced a large wind force blowing off his brother s hat. At that point, the brothers decided that they had a better blower than water wheel. Thus, the ROOTS blower concept and Roots Blower Company was created in their hometown of Connersville, Indiana, USA. The rotary positive blower, invented around the same time as the telegraph and steam engine, has withstood the test of time as the other inventions have fallen along the wayside. During the early years, the units proved reliable as low-pressure air sources for everything from blacksmith forges, to mine ventilation, to the first New York City subway. About Roots In 1893, an engineer broke from the Roots Blower Company and started the Connersville Blower Company. These two competitors continued in Connersville until 1931. At that time, the International Derrick and Equipment Company (IDECO) pruchased both firms and created the Roots-Connersville Blower Company. During 1931, Roots began to produce centrifugal compressors. Today, Roots manufactures integral-geared, and pedestal mounted, overhung, single-stage centrifugal compressors as well as horizontally split multi-stage centrifugal compressors. During WWII, Roots supplied Navy submarines and large surface craft with a special screw compressor used for ballast blowing. In 1944, Dresser Industries, Inc. acquired Roots to expand its range of services for the gas and oil industries. During 1998, Dresser Industries merged with the Halliburton Company. In 1999, the Roots and DMD Division of Dresser Equipment Group, Inc. combined and in 2000 joined with the Instrument Division to form Dresser Measurement. During 2001, Dresser Equipment Group separated from Halliburton through a management buy-out to form Dresser, Inc. Contents Accessories.................................... 3 Warranty....................................... 3 Operating Principles.............................. 3 Univesal RAI Series..............................4 Univesal RAI Performance Tables.................... 5 ROOTS XLP WHISPAIR........................... 7 XLP Series Performance Tables.................... 7 RAM Series.................................... 8 RAM Performance Tables......................... 9 RCS Series..................................... 10 RCS Series Performance Tables..................... 11 WHISPAIR Dry Exhausters.................... RAM WHISPAIR High-Pressure Blowers............. 13 DVJ & DPJ Performance Tables................... 11 Configurations................................. 14 Dimensional Drawings & Tables....................14 Typical Application Packages.................... 18 Contact Information.............................. 20 2 www.rootsblower.com
Operating Principles Two figure-eight lobe impellers mounted on parallel shafts rotate in opposite directions. As each impeller passes the blower inlet, it traps a finite volume of air and carries it around the case to the blower outlet, where Rotary Positive Blower Principle of Operation the air is discharged. With constant speed operation the displaced volume is essentially the same regardless of pressure, temperature or barometric pressure. Timing gears control the relative position of the impellers to each other and maintain small, but defined, clearances. This allows operation without lubrication being required inside the air casing. WHISPAIR Principle of Operation Incoming air is trapped by the impellers. Simultaneously, pressurized air (right) is being discharged. As the lower impeller passes the wrap-around flange, WHISPAIR jets equalize pressure between trapped air and the discharge area, aiding impeller movement and reducing power requirements. Impellers move air into the discharge area (right). Backflow is controlled, resulting in reduction of noise relative to conventional blowers. Tri-Lobe Blower Principle of Operation Incoming air is trapped by the pair of trilobe impellers. Simultaneously, pressurized air (right) is being discharged. As the lower impeller passes the wrap-around flange, WHISPAIR jets equalize pressure between trapped air and the discharge area, aiding impeller movement and reducing power requirements. Impellers move air into the discharge area (right). Backflow is controlled, resulting in reduction of noise relative to conventional blowers. Accessories Available accessories for ROOTS blowers, gas blowers and exhausters include driver, relief valves, inlet and discharge silencers, inlet filters, check valves, extended base, V-belt drive or flexible coupling and drive guards. Contact your Authorized Roots Distributor or Factory Sales Representative for details concerning your specific application or installation. www.rootsblower.com Warranty The Dresser Roots warranty covers Universal RAI and Universal RAI-J 2-1/2 to 7 inch gear diameter and RAM and RAM-J 4-1/2 to 6 inch gear diameter units for a full 24 months from original start-up date or 30 months from shipment, whichever occurs first. Full details are supplied in Warranty Policy WP-5020. 3
EasyAir 8000 Factory Blower Package System Design Features Dresser Roots-engineered noise abatement enclosure with power ventilation to optimize equipment life and extend reliability Patented automatic belt tension system Lightweight panels for ease of maintenance and blower unit access Minimized footprint for easy installation Front-mounted differential filter and discharge pressure gauges for easy viewing Up to 22dBA free field noise attenuation with enclosure Integrated forklift slots for convenient, balanced transportation The ROOTS EasyAir 8000 Factory Blower Package The Roots Advantages Powder-coated enclosure for durability and protection against harsh elements Dual-slash lubrication on units up to 6 (.24cm) gear diameter Removable locking panels for easy access Integrated grill guard for maintenance inspection without dismantling Intake volumes from 17.66 cfm (30 m 3 /hr) to 5297 cfm (9000 m 3 /hr) Pressures to psig (1034 Bargs) Motor horsepower to 500 hp (372 kw) Extremely compact design Short installation cycle time Low installation and operation cost Additional optional features available for ease of lubrication maintenance System is a noise abatement enclosure containing a pre-assembled, skid-mounted blower unit. All standard equipment is pre-mounted. It is produced for vacuum or pressure applications, enabling simple, on-site installation. Automatic Belt Tension System Standard Equipment ROOTS Dual Splash Lubricated Universal RAI, RAM, or TRI-NADO TM blowers TEFC EPACT motor Inlet filter silencer with paper element Filter restriction gauge Discharge base frame/discharge silencer Spring pressure relief valve Discharge pressure gauge (dual scale) Discharge check valve Vibration pads Manufacturer s standard paint on internal components Powder-coated finish on noise enclosure 2 www.rootsblower.com
Removeable panels for easy maintenance access. 1650 cfm (2804 m 3 /hr) 1100 cfm (1870 m 3 /hr) 195 cfm (331 m 3 /hr) EasyAir 8000 is available in popular performance ranges www.rootsblower.com 3
Universal RAI Series Rotary Positive Blowers/Vacuum Exhausters Basic Equipment Description All Universal RAI (U-RAI) series blowers are heavy duty rotary blowers in a compact, sturdy design engineered for continuous and maximum reliability. These blowers have grease lube on the drive-end with splash oil lube on the gear end. Roots exclusive figure-8 gearbox design improves oil distribution and lengthens bearing and gear life. This series features a grey iron casing, carburized and ground alloy steel spur timing gears secured to steel shafts with a taper fit and locknut, and grey iron involute impellers. Oversized anti-friction bearings are used, with a heavy duty cylindrical roller bearing at the drive shaft to withstand V-belt pull. Standard Universal RAI Air Units Frames 22 thru 718 The standard U-RAI blower features universal detachable rugged steel mounting feet to permit easy in-field adaptation to either vertical or horizontal installation requirements and any of four drive shaft positions top, bottom, right or left hand. All frame sizes are center-timed to allow for rotation in either direction. Universal RAI-J WHISPAIR Air Units Frames 33J thru 56J Roots refined the standard U-RAI line using computer-aided design techniques to incorporate the Roots exclusive WHISPAIR jet. The WHISPAIR jet uses shock suppression techniques for noise and pulsation reduction. This exclusive WHISPAIR feature can reduce noise 3-5 db on typical installations. Like the standard U-RAI blower, the U-RAI- J features universal detachable rugged steel mounting feet to permit easy in-field adaptation to any of four positions. Universal RAI Gas Units Frames 32GJ thru 6GJ U-RAI gas blowers feature mechanical seals and Viton o-rings. The seal system is designed to meet or exceed gas industry safety standards, including provisions for purge gas in the headplates. The U-RAI gas blower uses detachable rugged steel mounting feet for easy in-field adaptation of drive shaft position to meet vertical or horizontal installation requirements by exchanging the orientation of the mounting feet. 4 www.rootsblower.com
5 www.rootsblower.com Notes: 1. Pressure ratings based on inlet air at standard pressure of 14.7 psia, standard temperature of 68 F, and specific gravity of 1.0. 2. Vacuum ratings based on inlet air at standard temperature of 68 F, discharge of 30 Hg and specific gravity of 1.0. 22 24 32 33 36 42 45 47 53 56 59 65 68 6 76 711 718 1160 5275 1160 5275 1160 2800 1160 2800 1160 2800 860 860 860 700 2850 700 2850 700 2850 700 2350 700 2350 700 2350 575 1400 2050 575 1400 2050 575 1400 2050 10 49 76 24 102 6 40 113 149 55 6 205 95 262 344 38 92 204 79 188 410 105 249 542 72 211 355 3 358 598 187 529 881 140 400 546 224 643 876 420 05 1641 192 527 790 362 970 1450 600 90 2370 0.1 0.3 0.5 0.2 0.6 0.9 0.2 0.6 0.9 0.3 0.9 1.2 0.5 1.5 2.1 0.2 0.5 1.4 0.5 1.0 2.7 0.6 1.3 3.5 0.4 1.2 2.5 0.7 2.0 4.0 1.0 2.9 5.9 0.8 2.4 3.8 1.2 3.7 5.6 2.3 6.6 9.7 1.1 3.0 5.3 1.9 5.2 8.8 3.1 8.1 13.3 1 PSI 4 43 70 93 146 30 104 140 43 144 193 78 245 327 28 82 193 60 169 392 82 225 519 56 196 340 100 335 575 8 500 852 116 377 522 186 605 838 349 1133 70 163 497 760 316 925 1404 534 24 2304 0.2 0.8 1.3 0.5 1.6 2.4 0.7 1.7 2.3 0.9 2.4 3.2 1.6 3.9 5.3 0.7 1.4 3.3 1.4 2.9 6.5 1.8 3.8 8.5 1.2 3.2 5.8 2.0 5.4 9.5 3.0 7.9 13.9 2.3 6.2 8.9 3.7 9.8 13.7 6.8 17.9 24.8 3.1 8.0.5 5.6 14.2 22.0 9.1 22.8 34.7 3 PSI 36 63 81 135 19 93 9 28 9 178 57 224 306 69 181 37 146 369 53 196 490 38 177 321 72 306 547 464 816 86 347 492 139 557 790 260 1044 1481 6 460 723 258 867 1347 1.8 2.7 3.6 5.4 1.6 3.9 5.2 2.2 5.4 7.0 3.6 8.9 11.7 1.6 3.3 7.1 3.2 6.6 14.1 4.2 8.7 18.6 2.8 7.3.3 4.7.2 20.5 17.8 30.0 5.3 13.8 19.0 8.5 21.9 29.9.9 40.6 55.2 7.1 17.8 27.0 13.0 32.2 48.4 7 PSI 32 59 86 2 0 170 62 173 133 356 167 310 290 531 70 330 475 530 763 105 439 702 226 835 13 2.6 3.8 5.6 7.3 7.7 9.9 4.7 9.9 9.4 19.8 10.3 17.2 17.3 28.7 7.5 19.4 26.5 31.0 42.1 10.2 25.3 37.9 18.6 45.7 68.2 10 PSI 29 56 82 118 116 165 58 169 160 304 280 521 320 466 5 748 427 690 3.1 4.6 6.7 8.7 9.2 11.9 5.6 11.8.3 20.5 20.6 34.2 23.2 31.6 37.0 50.2 30.2 45.1 PSI 81 117 167 7 301 276 517.0 316 461 507 740 421 684 7.2 9.4.8 13.3 22.1 22.3 37.0 25.1 34.1 40.1 54.2 32.7 48.7 13 PSI Frame Size Speed RPM HGV 4 14 6 14 10 16 10 14 10 8 14 8 8 10 14 16 10 14 16 8 16 16 10 16 8 14 16 16 16 10 6 28 53 69 119 18 78 110 27 113 9 55 213 278 19 56 160 46 134 332 63 181 452 36 8 391 70 276 501 135 445 770 71 300 445 135 495 7 292 997 1389 117 413 674 228 793 56 446 1398 2178 0.2 1.8 2.8 0.5 3.5 5.5 1.1 4.1 5.3 1.5 5.2 7.3 2.5 7.5.1 0.9 3.2 7.3 1.8 5.5 14.5 2.4 7.3 19.1 2.0 7.1 13.4 3.3 11.8 22.4 3.9 14.9 30.8 4.4.2 25.6 5.9 22.7 32.8 8.9 33.9 53.4 6.0 19.7 29.5 10.9 33.5 53.1 14.8 43.6 64.7 Max. Vacuum Universal RAI Blower Performance 79 1 165 5 298 311 457 500 733 4 679 7.8 10.1 13.7 14.4 23.8 27.0 36.6 43.1 58.3 35.1 52.4 14 PSI 77 113 163 295 307 452 410 673 8.3 10.8 14.7 25.4 28.9 39.1 37.6 56.0 PSI
Universal RAI-J Performance Table Frame Size 33J 36J 45J 47J 56J Speed RPM 1160 2800 1160 2800 860 860 700 2850 4" Hg Vacuum 47 148 197 83 251 332 66 175 398 89 233 526 108 342 583 0.8 2.0 2.7 1.2 3.2 4.4 1.1 2.2 5.2 1.3 2.9 6.9 1.5 4.3 7.9 6" Hg Vacuum 40 141 190 74 241 323 56 164 387 76 220 513 95 329 570 1.1 2.7 3.6 1.7 4.4 6.0 1.5 3.1 7.1 1.9 4.1 9.3 2.2 5.9 10.6 8" Hg Vacuum 33 134 184 65 232 313 46 4 377 63 207 500 82 316 557 1.4 3.4 4.6 2.2 5.7 7.6 1.9 4.0 8.9 2.5 5.3 11.8 2.9 7.6 13.2 10" Hg Vacuum 27 8 177 55 223 304 144 367 51 194 488 70 304 545 1.7 4.1 5.3 2.7 6.6 8.7 4.9 10.3 3.0 6.3 13.6 3.5 9.0.2 " Hg Vacuum 1 170 213 294 134 356 181 474 291 532 4.9 6.3 7.9 10.3 14" Hg Vacuum 113 163 202 284 " Hg Vacuum 5.6 7.2 9 7. 6 9.1 11.9 278. 7 16" Hg Vacuum 5.8.2 345 14. 1 339. 0 32 7.5 16.1 460 18. 5 452 19. 8 10.6 17.9 276 517.3 20.6 510 21. 9 02 3. 9 5 23. 2 MAX. PRESSURE PSI 7 7 7 7 7 10 10 7 7 7 7 10 13 28 116 165 57 224 306 37 133 356 53 196 490 URAI-J Notes: 1. Pressure ratings based on inlet air at standard pressure of 14.7 psia, standard temperature of 68 F, and specific gravity of 1.0. 2. Vacuum ratings based on inlet air at standard temperature of 68 F, discharge of 30 Hg and specific gravity of 1.0. 72 290 517 2.4 9.5.4 3.8 9.5.5 3.4 9.5 20.5 4.4 9.0 19.5 4.9 17.9 38.0 Universal RAI-G Performance Table URAI-G Notes: 1. Performance based on METHANE at standard pressure of 14.7 psia, standard temperature of 68 F, and specific gravity of 0.55. 2. For vacuum service consult factory or nearest Roots sales office. 6 www.rootsblower.com
ROOTS XLP WHISPAIR Extra Low Pulse Tri-Lobe Blowers Basic Blower Description ROOTS XLP WHISPAIR blowers are specially designed to reduce noise and power loss by combining the exclusive ROOTS WHISPAIR wraparound plenum and exclusive double jet to control pressure equalization with a tri-lobe impeller design. The tri-lobe impeller profile ensures maximum volumetric efficiency and minimum absorbed power without sacrificing torsional rigidity. Designed for long operating life, the XLP tri-lobe blower features large-diameter rolling element bearings with high load-carrying capacity. XLP blowers are splash lubricated on both ends, incorporating an oil slinger design that eliminates the need for lip seals. Taper mounted, precision ground, and hardened high-grade alloy steel gears ensure smooth, quiet operation. Cylinder and headplates are made from cast iron with dynamically-balanced ductile iron impellers and integral shafts. All units are designed with rugged steel mounting feet that permit in-field adaptability to either vertical or horizontal installation requirements. XLP Series Performance Table Notes: 1. Pressure ratings based on inlet air at standard pressure of 14.7 psia, standard temperature of 68 F, and specific gravity of 1.0. 2. Vacuum ratings based on inlet air at standard temperature of 68 F, discharge of 30 Hg and specific gravity of 1.0. www.rootsblower.com 7
RAM Series Rotary Positive Blowers/Exhausters Basic Equipment Description ROOTS RAM series units are recognized as the most volumetrically efficient equipment in the industry. Unless otherwise noted, RAM series equipment may operate under either vacuum or pressure application with no equipment modification, and can provide simultaneous vacuum and pressure for a system with a single unit. RAM series units feature integral-shaft ductile iron impellers with involute profiles. Headplates and the rigid casing are cast grey iron, while the drive end and gear covers are aluminum. Carburized ground alloy steel spur timing gears are securely mounted on taper end shafts. All units in the RAM series feature cylindrical roller bearings for maximum life. Detachable steel mounting feet permit in-field adaptability to either vertical or horizontal installation requirements. Piston-ring shaft seals reduce gas leakage through the headplates, while lip-type oil seals prevent lubricant from entering the air chamber. RAM units are splash lubricated on both sides with high volume oil reservoirs. Standard RAM Rotary Air Units Frames 404 thru 624 All standard units are center-timed to allow rotation in either direction. RAM WHISPAIR Rotary Air Units Frames 404J thru 624J RAM-J units feature the exclusive WHISPAIR jets to control pressure equalization by feeding backflow in the direction of impeller movement, thereby aiding rotation. RAM WHISPAIR Water Sealed Exhausters Frames 404J thru 624J RAM WHISPAIR units are available equipped with an inlet spray nozzle and seal water flow meter for water injection. This feature cools the vacuum unit to enable the unit to reach deeper vacuum while minimizing potential impeller and casing distortion. RAM Gas Units Available on all RAM Frame Sizes RAM standard gas blowers feature a piston ring system between the compression chamber and vent cavities. All vent cavities are plugged for purge or drain. Special long-life mechanical seals and Viton 0-rings are installed at each bearing to control gas and oil leakage. The seal incorporates a unique geometry that promotes enhanced cooling and extended seal life. RAM gas units are suitable for both vacuum or pressure service. Alternate material units and optional 0-ring material are available for gas units, please contact the factory for more information. 8 www.rootsblower.com
RAM Performance Table RAM-J and RAM-GJ Performance Table RAM-J Water Sealed Performance Table Notes: 1. Pressure ratings based on inlet air at standard pressure of 14.7 psia, standard temperature of 68 F, and specific gravity of 1.0. 2. Vacuum ratings based on inlet air at standard temperature of 68 F, discharge of 30 Hg and specific gravity of 1.0. www.rootsblower.com 9
RCS Series Rotary Positive Blowers/Exhausters RCS Series Description RCS rotary positive blowers are heavy-duty units designed with integral-shaft ductile iron impellers with involute profile. The headplates, gear cover, drive end cover and rigid, one-piece casing are grey iron. Carburized and ground alloy steel spur timing gears are taper mounted on the shafts and secured with a locknut. Cylindrical roller bearings are used. Piston rings reduce air leakage through the headplate shaft openings, while lip-type oil seals prevent lubricant from entering the air chamber. All RCS series blowers are equipped with splash oil lubrication at both ends of the blower. Unless otherwise noted, RCS series units incorporate detachable rugged steel mounting feet to permit in-field adaptability to either vertical or horizontal installation. RCS blowers are available in frames 817 thru 827, and with ROOTS WHISPAIR frames available in 7J thru 832J. RCS WHISPAIR Rotary Positive Blowers Frames 7J thru 832J RCS WHISPAIR units reduce noise and power loss by utilizing an exclusive wrap-around plenum and proprietary WHISPAIR jet portals to control pressure equalization. The WHISPAIR jets meter discharge pressure in the direction of impeller movement, thereby aiding rotation. Discharge pulsation is reduced by the pre-pressurization of the blower chamber. Reduced pulsation results in lower noise, and reduced shock loading on the impellers. RCS WHISPAIR units frames 817J thru 832J have feet integral to the headplates. 10 www.rootsblower.com
RCS Series Performance Table RCS-J Series Performance Table Notes: 1. Pressure ratings based on inlet air at standard pressure of 14.7 psia, standard temperature of 68 F, and specific gravity of 1.0. 2. Vacuum ratings based on inlet air at standard temperature of 68 F, discharge of 30 Hg and specific gravity of 1.0. 3. 800J frame sizes only - Operation above psi pressure rise, Hg vacuum or 230 F temperature rise requires oil coolers - refer to factory. Oil coolers not available on 600J and 700J frame sizes. www.rootsblower.com 11
WHISPAIR Dry Exhausters Basic Dry Exhausters Description ROOTS dry exhausters feature an exclusive discharge jet plenum designed to allow cool, atmospheric air to flow into the casing. This unique design permits continuous operation at levels to blank-off with a single stage unit, without water injection or heat exchangers. Competitor s dry exhausters, not having the benefit of the WHISPAIR jet plenum are limited to approximately 16 Hg due to extreme discharge temperatures resulting in casing and impeller distortion. Headplates and the rigid casing are cast from grey iron, with aluminum drive end and gear covers. Carburized ground alloy steel spur timing gears are securely mounted on taper end shafts. All DVJ exhausters are designed with detachable steel mounting feet to permit in-field adaptability to discharge left, right or vertically upwards. WHISPAIR Dry Exhausters Frame 2504 DVJ Frame 2504 DVJ units feature ball bearings, with splash lubrication at the gear end and grease lubrication at the drive end. Lip-type seals restrict oil leakage into the air stream. Frame 721 DVJ Frame 721 DVJ units feature cylindrical roller bearings with splash lubrication at both the gear end and the drive end. Lip-type seals restrict oil leakage into the air stream. RAM WHISPAIR Dry Exhausters Frame 406 DVJ, 4 DVJ, and 616 DVJ RAM DVJ units feature integral-shaft ductile iron impellers with involute profiles. Headplates and the rigid casing are cast grey iron, while gearbox and end covers are aluminum. Carburized ground alloy steel spur timing gears are securely mounted on taper end shafts. The top shaft is extended for drive side outlet blowers, and either shaft can be extended for drive on top or bottom outlet blowers. RAM DVJ units feature cylindrical roller bearings for maximum live. Piston ring shaft seals reduce gas leakage through the headplates, while lip-type oil seals prevent lubricant from entering the air chamber. RAM DVJ units are splash lubricated on both sides with high volume oil reservoirs. RAM DVJ units can be equipped with mechanical seals for gas applications. Please contact the factory for more information. www.rootsblower.com
RAM WHISPAIR Dry High-Pressure Blowers Frame 406 DPJ ROOTS dry high-pressure blowers feature an exclusive discharge jet plenum designed to allow externally cooled gas to flow into the casing. Additionally, the ROOTS WHISPAIR jets control pressure equalization by feeding backflow in the direction of impeller movement, thereby aiding rotation. The unique WHISPAIR design permits continuous operation with discharge pressures up to 30 PSIG in a single stage unit. ROOTS high-pressure units produce temperatures up to 370 F, and are therefore ideal for designing systems with plant heat co-generation capabilities. Headplates and the rigid casing are forged from grey iron, with aluminum drive end and gear covers. Carburized ground alloy steel spur timing gears are securely mounted on taper end shafts. RAM DPJ units feature cylindrical roller bearings and is splash lubricated at both the gear and drive ends. Piston rings are used to reduce air leakage through the headplate shaft openings, while lip-type oil seals prevent lubricant from entering the air chamber. All DPJ high-pressure blowers are designed with detachable steel mounting feet to permit in-field adaptability to either left, right or vertically upwards. The top shaft is extended for drive side outlet blowers, and either shaft can be extended for drive on top outlet blowers. RAM DPJ units are suitable for air or gas applications. Performance Tables Dry Vacuum Exhausters and Dry High-Pressure Blowers DVJ DPJ Notes: 1. Vacuum ratings based on inlet air and jet air standard pressure and standard temperature of 68 F, discharge and jet pressures of 30 Hg and specific gravity of 1.0. 2. Refer to factory for performance guarantee above 24 HgV. 3. DPJ ratings based on inlet air at standard pressure of 14.7 psia, standard temperature of 68 F, and specific gravity of 1.0. www.rootsblower.com 13
Configurations ROOTS blowers and compressors are available in two basic configurations to meet nearly any piping arrangement or installation requirement. Orientation for inlet and discharge connections is determined from the drive end: LEFT: Vertical Configuration RIGHT: Horizontal Configuration Vertical Configuration: For vertical configuration, one impeller is mounted above the other, unless otherwise noted the blower drive end located opposite the timing gears. Inlet and discharge connection flanges are positioned to provide horizontal air/gas flow. Specify blower driver for either top or bottom connection. Horizontal Configuration: For horizontal configuration, impellers are located side-byside. Unless otherwise noted, the blower drive end is located opposite the timing gears. Inlet and discharge connection flanges provide a vertical air/gas flow. Specify blower driver for either left or right hand blower shaft. Special Note: URAI-J models are designed to operate with only one shaft rotation direction to take full advantage of the WHI- SPAIR feature. Therefore, a URAI-J blower should be operated in the following combinations only: CCW Rotation: Bottom Shaft; Right side discharge or a Left Shaft; Bottom discharge. CCW Rotation: Top Shaft; Left side discharge or a Right Shaft; Top discharge. CW Rotation: Bottom Shaft; Left side discharge or a Right Shaft; Bottom discharge. CW Rotation: Top Shaft; Right side discharge or a Left Shaft; Top discharge. Dimensional Drawings and Tables RCS Dimensional Table 14 www.rootsblower.com
Universal RAI Dimensional Table RAM Dimensional Table www.rootsblower.com
URAI-J Dimensional Table RAM-J Dimensional Table XLP Dimensional Table 16 www.rootsblower.com
RCS-J Dimensional Table DVJ Dimensional Table DPJ Dimensional Table www.rootsblower.com 17
Typical Application Packages Pressure Application Gas Application 18 www.rootsblower.com
Exhauster Application High-Vacuum Application www.rootsblower.com 19
Contact List CUSTOMER SERVICE Dresser Roots 16240 Port Northwest Drive Houston, TX 77041 Toll Free Hot Line: 1-877-363-ROOT(S) (7668) Toll Free Fax: 1-877-357-7238 Roots Factory Service & Repair Centers Dresser Roots Houston Service Center Dresser Roots Factory Service & Repair Center 11611B Tanner Rd. Houston, TX 77041 Ph: 713-896-4810 Fax: 713-896-4927 Dresser Roots Connersville Service Center Dresser Roots Factory Service & Repair Center 900 West Mount Street Connersville, IN 47331 Ph: 765-827-9200 Fax: 765-827-9266 Dresser Roots United Kingdom Service Center Dresser Roots Factory Service & Repair Center PO Box B7 Off St Andrews Road Turnbridge, Huddersfield England HD1 6RB Ph: +44 (0) 1484 422 222 Aftermarket Direct Line: +44 (0) 1484 487 669 Aftermarket email: graeme.wadsworth@dresser.co.uk Aftermarket Fax: +44 (0) 1484 487 657 Dresser Roots Mexico Service Center Dresser Roots Factory Service & Repair Center Henry Ford No 114 Esq. Roberto Fulton Fracc. Industrial San Nicolas Tlalnepantla, Edo de Mexico Cp 54030 Ph: +52 55 5317 5486 Fax: +52 55 5317 5358 B-05X93 October 2005 Dresser Roots Headquarters 16240 Port Northwest Drive Houston, TX 77041 Toll Free (US): 1-877-363-7668 Toll Free Fax: 1-877-357-7238 Dresser Roots Connersville Operation 900 West Mount Street Connersville, IN 47331 Ph: 765-827-9200 Fx: 765-827-9266 Dresser Roots Holmes Operation PO Box B7 Off St. Andrews Rd Turnbridge, Huddersfield England HD1 6RB Ph: +44-1484-422222 Fx: +44-1484-422668 website: www.rootsblower.com US email: roots@dresser.com UK email: dmd_roots@dresser.co.uk 2005 Dresser, Inc. all rights reserved. Printed in the U.S.A. All information subject to change without notice ROOTS and Universal RAI are registered trademarks of Dresser, Inc. Universal RAI-J, Universal RAI-G, RAM, WHISPAIR and XLP are trademarks of Dresser, Inc.