Edition 2007:1 Industrial & Marine Engines Section 5 Engine data Engines for power generation Contents General information... 3 Engine program... 4 Basic data... 6 Technical data and cooling equipment recommendation DC12 53A, order ref 10-16A... 8 DC12 60A, order ref 10-17A... 9 DC12 60A, order ref 10-18A... 10 DC12 60A, order ref 10-19A... 11 DC12 60A, order ref 10-20A... 12 DC12 52A, order ref 10-30A... 13 DC12 59A, order ref 10-31A... 14 DC12 59A, order ref 10-32A... 15 DC12 59A, order ref 10-33A... 16 DC12 59A, order ref 10-34A... 17 DC12 56A, order ref 10-10A... 18 DC12 56A, order ref 10-11A... 19 DC12 56A, order ref 10-12A... 20 DC12 56A, order ref 10-13A... 21 DC12 56A, order ref 10-14A... 22 DC12 56A, order ref 10-15A... 23 Basic dimensions DC12... 24 Equipment list... 26 Part No. 1 588 879 Scania CV AB Sweden
Latest modification date: 070301 General information Standard equipment Unit injectors and EMS Turbo charger Fuel filter Fuel pre-filter with water separator Centrifugal oil cleaner Oil filter Oil cooler Starter: 1-pole, 5.5 kw, 24 V (EMS controlled) Alternator: 1-pole, 65A, 28 V incl. relay and connection for tachometer Flywheel Silumin flywheel housing, SAE1 flange Front mounted engines brackets Operator s manual For optional equipment, see Equipment list page 26 Ratings PRP: Prime power ESP: Maximum stand-by power Descriptions of ratings and other power information, see General, sect.2 Emission compliance DC12 52A, DC12 59A complies with EU Stage II emission regulations. DC12 56A complies with US Tier 3 emission regulations. For detailed information about approved and certified engines, access SAIL at http://sail.scania.com to view or download the appropriate certificate. 2007:1 Scania Industrial & Marine Engines Part No. 1 588 879 3
Latest modification date: 060701 Engine program Non-compliant engines 1500 rpm (50Hz) PRP 1800 rpm (60Hz) 1500 rpm (50Hz) ESP 1800 rpm (60Hz) Factory order reference sequence (rating, engine speed, output, engine type) DC12 53A kw - 405-445 DC12 60A* kw 270 298 313 341 DC12 60A* kw 313 341 356 384 DC12 60A* kw 356 384 399 406 DC12 60A kw 399-437 - PRP 13-03, 35-11, 12-26, 10-16A ESP 13-04, 35-11, 12-08, 10-16A PRP 13-03, 35-20, 12-34, 10-17A ESP 13-04, 35-20, 12-37, 10-17A PRP 13-03, 35-20, 12-35, 10-18A ESP 13-04, 35-20, 12-38, 10-18A PRP 13-03, 35-20, 12-36, 10-19A ESP 13-04, 35-20, 12-39, 10-19A PRP 13-03, 35-05, 12-09, 10-20A ESP 13-04, 35-05, 12-10, 10-20A EU Stage II compliant engines 1500 rpm (50Hz) PRP 1800 rpm (60Hz) 1500 rpm (50Hz) ESP 1800 rpm (60Hz) Factory order reference sequence (rating, engine speed, output, engine type) DC12 52A kw - 405-445 DC12 59A* kw 270 298 313 341 DC12 59A* kw 313 341 356 384 DC12 59A* kw 356 384 399 406 DC12 59A kw 399-437 - PRP 13-03, 35-11, 12-26, 10-30A ESP 13-04, 35-11, 12-08, 10-30A PRP 13-03, 35-20, 12-34, 10-31A ESP 13-04, 35-20, 12-37, 10-31A PRP 13-03, 35-20, 12-35, 10-32A ESP 13-04, 35-20, 12-38, 10-32A PRP 13-03, 35-20, 12-36, 10-33A ESP 13-04, 35-20, 12-39, 10-33A PRP 13-03, 35-05, 12-09, 10-34A ESP 13-04, 35-05, 12-10, 10-34A *) = Standard with dual speed configuration. The engine speed can be switched between 50Hz / 60Hz via the Coordinator/EMS. Note! that the default setting is 50Hz from factory. To manually change the nominal speed please refer to the installation instruction documentation 19:01-20 in the workshop manual or the CAN specification and EMS/S6 software function description located on SAIL at http://sail.scania.com. 4 Part No. 1 588 879 Scania Industrial & Marine Engines 2007:1
Latest modification date: 060701 US Tier 3 compliant engines PRP ESP 1800 rpm (60Hz) 1800 rpm (60Hz) DC12 56A kw 273 300 DC12 56A kw 300 316 DC12 56A kw 316 337 DC12 56A kw 337 359 DC12 56A kw 359 381 DC12 56A kw 381 403 Factory order reference sequence (rating, engine speed, output, engine type) PRP 13-03, 35-11, 12-20, 10-10A ESP 13-04, 35-11, 12-19, 10-10A PRP 13-03, 35-11, 12-19, 10-11A ESP 13-04, 35-11, 12-22, 10-11A PRP 13-03, 35-11, 12-22, 10-12A ESP 13-04, 35-11, 12-23, 10-12A PRP 13-03, 35-11, 12-23, 10-13A ESP 13-04, 35-11, 12-24, 10-13A PRP 13-03, 35-11, 12-24, 10-14A ESP 13-04, 35-11, 12-17, 10-14A PRP 13-03, 35-11, 12-17, 10-15A ESP 13-04, 35-11, 12-18, 10-15A 2007:1 Scania Industrial & Marine Engines Part No. 1 588 879 5
Latest modification date: 060701 Basic data General Configuration and number of cylinders............................ 6 in-line Working principle.............................4 stroke Bore x stroke mm........................... 127 x 154 Displacement dm 3...............................11,70 Compression ratio............................... 16:1 DC12 56A............................... 18:1 Firing order.....................1-5 - 3-6 - 2-4 Piston speed at 1500 r/min m/s................................7,70 at 1800 r/min m/s................................9,24 Rotation, seen from flywheel end.................... Counter clockwise Moment of inertia with flywheel for 14 coupling kgm 2................................2,74 Number of teeth on flywheel ring gear................................ 158 Weight approx., excl. oil and coolant kg................................ 980 Lubrication system Oil capacity dm 3, min................................. 28 max................................. 33 Oil consumption g/kwh............................... < 0.3 Oil change intervals h................................ 400 Oil grade.................. CE or CF acc. to API CCMC D5 Acea E3-96 Oil Pressure Normal bar............................... 3-6 Minimum permitted bar.................................0.7 Oil temperature Maximum permitted C................................ 120 Oil cleaner.................. Paper and centrifugal Filtration Micron............................... 5-7 Oil filter for turbo charger.............................. Paper Oil cooler.................water cooled/full flow 6 Part No. 1 588 879 Scania Industrial & Marine Engines 2007:1
Latest modification date: 060701 Injection system Type Governor Fuel filter............... Electronic Unit Injectors Scania Engine Management System (EMS)................... Paper filter element Cooling system Coolant volume, excl. radiator dm 3................................. 22 Coolant temperature C............................. 75-85 Number of thermostats.................................. 1 Opening temperature C................................. 75 Intake system Permissible pressure drop in intake system with cleaned or new filter mmwc................................ 300 Permissible pressure drop in intake system with blocked (dirty) filter mmwc................................ 500 Electrical system, optional equipment Type Optional Starter, standard equipment Optional Alternator, standard equipment Optional..................... 1-pole, 24 V, DC..................... 2-pole, 24 V, DC................. 1-pole, 24 V - 5.5 kw................. 2-pole, 24 V - 6.7 kw................... 1-pole, 28 V - 65 A................... 2-pole, 28 V - 65 A.................. 1-pole, 28 V - 100 A 2007:1 Scania Industrial & Marine Engines Part No. 1 588 879 7
Latest modification date: 060701 Technical data and cooling equipment recommendation DC12 53A, order ref 10-16A 1800 r/min PRP ESP Gross power kw 405 445 kva* 458 510 Specific fuel consumption g/kwh full load 192 197 3/4 load 189 189 1/2 load 193 192 Heat rejection kw to cooling water 151 171 to exhaust gas 266 303 to charge air 80 94 to surrounding air 34 38 Air consumption kg/min 32 34 Air temperature before charge air cooler C 193 204 Air temperature after charge air cooler C 37 39 Fall of pressure, charge air cooler Bar 0.09 0.10 Exhaust flow kg/min 33 35 Exhaust temperature C 459 494 *The kva range is calculated with the recommended fan for +35 C air-on temperature to cooling system including the fan power losses at a generator efficiency common to the market. For further information see General, sect. 2. 1800 r/min PRP ESP Air-on temp. Air-on temp. 35 C 50 C 35 C 50 C Radiator front area m 2 1.2 1.3 1.3 1.3 Coolant pump flow dm 3 /min 300 300 300 300 Fan type Pusher Pusher Pusher Pusher Ø mm 912 912 912 912 power losses kw 11 11 11 11 speed ratio 1:0.8 1:0.8 1:0.8 1:0.8 Air flow free air flow m 3 /s 8.0 8.0 8.0 8.0 pressure reserve mm Wc 21 30 23 17 8 Part No. 1 588 879 Scania Industrial & Marine Engines 2007:1
Latest modification date: 060701 Technical data and cooling equipment recommendation DC12 60A, order ref 10-17A 1500 r/min 1800 r/min PRP ESP PRP ESP Gross power kw 270 313 298 341 kva* 298 351 334 384 Specific fuel consumption g/kwh full load 190 190 192 192 3/4 load 193 191 194 193 1/2 load 199 197 203 200 Heat rejection kw to cooling water 102 118 113 129 to exhaust gas 181 203 195 218 to charge air 36 47 49 60 to surrounding air 23 27 25 28 Air consumption kg/min 21 24 27 29 Air temperature before charge air cooler C 135 154 145 161 Air temperature after charge air cooler C 38 41 40 44 Fall of pressure, charge air cooler Bar 0.07 0.07 0.11 0.11 Exhaust flow kg/min 22 25 28 31 Exhaust temperature C 494 507 446 464 *The kva range is calculated with the recommended fan for +35 C air-on temperature to cooling system including the fan power losses at a generator efficiency common to the market. For further information see General, sect. 2. 1500 r/min 1800 r/min PRP ESP PRP ESP Air-on temp. Air-on temp. Air-on temp. Air-on temp. 35 C 50 C 35 C 50 C 35 C 50 C 35 C 50 C Radiator front area m 2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 Coolant pump flow dm 3 /min 300 300 300 300 360 360 360 360 Fan type Pusher Pusher Pusher Pusher Pusher Pusher Pusher Pusher Ø mm 912 912 912 912 912 912 912 912 power losses kw 11 11 11 11 11 11 11 11 speed ratio 1:1 1:1 1:1 1:1 1:0.8 1:0.8 1:0.8 1:0.8 Air flow free air flow m 3 /s 8.0 8.0 8.0 8.0 7.8 7.8 7.8 7.8 pressure reserve mm Wc 49 43 40 32 44 37 32 28 2007:1 Scania Industrial & Marine Engines Part No. 1 588 879 9
Latest modification date: 060701 Technical data and cooling equipment recommendation DC12 60A, order ref 10-18A 1500 r/min 1800 r/min PRP ESP PRP ESP Gross power kw 313 356 341 384 kva* 351 401 384 434 Specific fuel consumption g/kwh 190 192 192 193 full load 191 190 193 192 3/4 load 197 195 200 197 1/2 load Heat rejection kw to cooling water 118 136 129 147 to exhaust gas 203 232 218 245 to charge air 47 59 60 72 to surrounding air 27 31 28 32 Air consumption kg/min 24 27 29 32 Air temperature before charge air cooler C 154 174 161 179 Air temperature after charge air cooler C 41 45 44 48 Fall of pressure, charge air cooler Bar 0.07 0.08 0.11 0.12 Exhaust flow kg/min 25 28 31 33 Exhaust temperature C 507 524 464 489 *The kva range is calculated with the recommended fan for +35 C air-on temperature to cooling system including the fan power losses at a generator efficiency common to the market. For further information see General, sect. 2. 1500 r/min 1800 r/min PRP ESP PRP ESP Air-on temp. Air-on temp. Air-on temp. Air-on temp. 35 C 50 C 35 C 50 C 35 C 50 C 35 C 50 C Radiator front area m 2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 Coolant pump flow dm 3 /min 300 300 300 300 360 360 360 360 Fan type Pusher Pusher Pusher Pusher Pusher Pusher Pusher Pusher Ø mm 912 912 912 912 912 912 912 912 power losses kw 11 11 11 11 11 11 11 11 speed ratio 1:1 1:1 1:1 1:1 1:0.8 1:0.8 1:0.8 1:0.8 Air flow free air flow m 3 /s 8.0 8.0 8.0 8.0 7.8 7.8 7.8 7.8 pressure reserve mm Wc 40 32 30 26 32 28 27 23 10 Part No. 1 588 879 Scania Industrial & Marine Engines 2007:1
Latest modification date: 060701 Technical data and cooling equipment recommendation DC12 60A, order ref 10-19A 1500 r/min 1800 r/min PRP ESP PRP ESP Gross power kw 356 399 384 406 kva* 401 451 434 459 Specific fuel consumption g/kwh full load 192 194 193 194 3/4 load 190 190 192 191 1/2 load 195 193 197 196 Heat rejection kw to cooling water 136 154 147 156 to exhaust gas 232 263 245 261 to charge air 59 73 72 78 to surrounding air 31 35 32 34 Air consumption kg/min 27 30 32 33 Air temperature before charge air cooler C 174 192 179 187 Air temperature after charge air cooler C 45 50 48 50 Fall of pressure, charge air cooler Bar 0.08 0.10 0.12 0.13 Exhaust flow kg/min 28 31 33 34 Exhaust temperature C 524 543 489 502 *The kva range is calculated with the recommended fan for +35 C air-on temperature to cooling system including the fan power losses at a generator efficiency common to the market. For further information see General, sect. 2. 1500 r/min 1800 r/min PRP ESP PRP ESP Air-on temp. Air-on temp. Air-on temp. Air-on temp. 35 C 50 C 35 C 50 C 35 C 50 C 35 C 50 C Radiator front area m 2 1.2 1.2 1.2 1.3 1.2 1.2 1.2 1.3 Coolant pump flow dm 3 /min 300 300 300 300 360 360 360 360 Fan type Pusher Pusher Pusher Pusher Pusher Pusher Pusher Pusher Ø mm 912 912 912 912 912 912 912 912 power losses kw 11 11 11 11 11 11 11 11 speed ratio 1:1 1:1 1:1 1:1 1:0.8 1:0.8 1:0.8 1:0.8 Air flow free air flow m 3 /s 8.0 8.0 8.0 8.0 7.8 7.8 7.8 7.8 pressure reserve mm Wc 30 26 24 30 27 23 20 30 2007:1 Scania Industrial & Marine Engines Part No. 1 588 879 11
Latest modification date: 060701 Technical data and cooling equipment recommendation DC12 60A, order ref 10-20A 1500 r/min PRP ESP Gross power kw 399 437 kva* 451 501 Specific fuel consumption g/kwh full load 194 197 3/4 load 190 191 1/2 load 193 192 Heat rejection kw to cooling water 154 170 to exhaust gas 263 292 to charge air 73 84 to surrounding air 35 39 Air consumption kg/min 30 31 Air temperature before charge air cooler C 192 211 Air temperature after charge air cooler C 50 54 Fall of pressure, charge air cooler Bar 0.10 0.12 Exhaust flow kg/min 31 33 Exhaust temperature C 543 567 *The kva range is calculated with the recommended fan for +35 C air-on temperature to cooling system including the fan power losses at a generator efficiency common to the market. For further information see General, sect. 2. 1500 r/min PRP ESP Air-on temp. Air-on temp. 35 C 50 C 35 C 50 C Radiator front area m 2 1.2 1.3 1.3 1.3 Coolant pump flow dm 3 /min 300 300 300 300 Fan type Pusher Pusher Pusher Pusher Ø mm 912 912 912 912 power losses kw 11 11 11 11 speed ratio 1:1 1:1 1:1 1:1 Air flow free air flow m 3 /s 8.0 8.0 8.0 8.0 pressure reserve mm Wc 24 30 26 20 12 Part No. 1 588 879 Scania Industrial & Marine Engines 2007:1
Latest modification date: 060701 Technical data and cooling equipment recommendation DC12 52A, order ref 10-30A 1800 r/min PRP ESP Gross power kw 405 445 kva* 458 510 Specific fuel consumption g/kwh full load 198 198 3/4 load 198 198 1/2 load 201 200 Heat rejection kw to cooling water 165 174 to exhaust gas 280 307 to charge air 85 94 to surrounding air 35 38 Air consumption kg/min 32 34 Air temperature before charge air cooler C 193 204 Air temperature after charge air cooler C 38 40 Fall of pressure, charge air cooler Bar 0.09 0.10 Exhaust flow kg/min 33 35 Exhaust temperature C 472 494 *The kva range is calculated with the recommended fan for +35 C air-on temperature to cooling system including the fan power losses at a generator efficiency common to the market. For further information see General, sect. 2. 1800 r/min PRP ESP Air-on temp. Air-on temp. 35 C 50 C 35 C 50 C Radiator front area m 2 1.2 1.3 1.3 1.3 Coolant pump flow dm 3 /min 300 300 300 300 Fan type Pusher Pusher Pusher Pusher Ø mm 912 912 912 912 power losses kw 11 11 11 11 speed ratio 1:0.8 1:0.8 1:0.8 1:0.8 Air flow free air flow m 3 /s 8.0 8.0 8.0 8.0 pressure reserve mm Wc 16 25 18 12 2007:1 Scania Industrial & Marine Engines Part No. 1 588 879 13
Latest modification date: 060701 Technical data and cooling equipment recommendation DC12 59A, order ref 10-31A 1500 r/min 1800 r/min PRP ESP PRP ESP Gross power kw 270 313 298 341 kva* 298 351 334 384 Specific fuel consumption g/kwh full load 208 208 206 202 3/4 load 207 207 210 208 1/2 load 210 209 216 213 Heat rejection kw to cooling water 112 130 122 138 to exhaust gas 217 248 229 249 to charge air 47 59 59 68 to surrounding air 25 29 27 30 Air consumption kg/min 24 27 29 31 Air temperature before charge air cooler C 152 172 160 174 Air temperature after charge air cooler C 41 46 44 47 Fall of pressure, charge air cooler Bar 0.07 0.07 0.11 0.11 Exhaust flow kg/min 25 28 30 32 Exhaust temperature C 513 531 468 484 *The kva range is calculated with the recommended fan for +35 C air-on temperature to cooling system including the fan power losses at a generator efficiency common to the market. For further information see General, sect. 2. 1500 r/min 1800 r/min PRP ESP PRP ESP Air-on temp. Air-on temp. Air-on temp. Air-on temp. 35 C 50 C 35 C 50 C 35 C 50 C 35 C 50 C Radiator front area m 2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 Coolant pump flow dm 3 /min 300 300 300 300 360 360 360 360 Fan type Pusher Pusher Pusher Pusher Pusher Pusher Pusher Pusher Ø mm 912 912 912 912 912 912 912 912 power losses kw 11 11 11 11 11 11 11 11 speed ratio 1:1 1:1 1:1 1:1 1:0.8 1:0.8 1:0.8 1:0.8 Air flow free air flow m 3 /s 8.0 8.0 8.0 8.0 7.8 7.8 7.8 7.8 pressure reserve mm Wc 45 39 36 28 40 33 28 24 14 Part No. 1 588 879 Scania Industrial & Marine Engines 2007:1
Latest modification date: 060701 Technical data and cooling equipment recommendation DC12 59A, order ref 10-32A 1500 r/min 1800 r/min PRP ESP PRP ESP Gross power kw 313 356 341 384 kva* 351 401 384 434 Specific fuel consumption g/kwh full load 208 205 202 198 3/4 load 207 207 208 206 1/2 load 209 208 213 211 Heat rejection kw to cooling water 130 145 138 152 to exhaust gas 248 269 249 266 to charge air 59 69 68 77 to surrounding air 29 33 30 33 Air consumption kg/min 27 29 31 33 Air temperature before charge air cooler C 172 189 174 185 Air temperature after charge air cooler C 46 49 47 50 Fall of pressure, charge air cooler Bar 0.07 0.08 0.11 0.12 Exhaust flow kg/min 28 30 32 34 Exhaust temperature C 531 545 484 499 *The kva range is calculated with the recommended fan for +35 C air-on temperature to cooling system including the fan power losses at a generator efficiency common to the market. For further information see General, sect. 2. 1500 r/min 1800 r/min PRP ESP PRP ESP Air-on temp. Air-on temp. Air-on temp. Air-on temp. 35 C 50 C 35 C 50 C 35 C 50 C 35 C 50 C Radiator front area m 2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 Coolant pump flow dm 3 /min 300 300 300 300 360 360 360 360 Fan type Pusher Pusher Pusher Pusher Pusher Pusher Pusher Pusher Ø mm 912 912 912 912 912 912 912 912 power losses kw 11 11 11 11 11 11 11 11 speed ratio 1:1 1:1 1:1 1:1 1:0.8 1:0.8 1:0.8 1:0.8 Air flow free air flow m 3 /s 8.0 8.0 8.0 8.0 7.8 7.8 7.8 7.8 pressure reserve mm Wc 36 28 26 22 28 24 23 19 2007:1 Scania Industrial & Marine Engines Part No. 1 588 879 15
Latest modification date: 060701 Technical data and cooling equipment recommendation DC12 59A, order ref 10-33A 1500 r/min 1800 r/min PRP ESP PRP ESP Gross power kw 356 399 384 406 kva* 401 451 434 459 Specific fuel consumption g/kwh full load 205 201 198 197 3/4 load 207 208 206 205 1/2 load 208 207 211 211 Heat rejection kw to cooling water 145 160 152 159 to exhaust gas 269 287 266 276 to charge air 69 78 77 81 to surrounding air 33 36 33 35 Air consumption kg/min 29 30 33 34 Air temperature before charge air cooler C 189 203 185 191 Air temperature after charge air cooler C 49 52 50 51 Fall of pressure, charge air cooler Bar 0.08 0.10 0.12 0.13 Exhaust flow kg/min 30 32 34 35 Exhaust temperature C 545 559 499 508 *The kva range is calculated with the recommended fan for +35 C air-on temperature to cooling system including the fan power losses at a generator efficiency common to the market. For further information see General, sect. 2. 1500 r/min 1800 r/min PRP ESP PRP ESP Air-on temp. Air-on temp. Air-on temp. Air-on temp. 35 C 50 C 35 C 50 C 35 C 50 C 35 C 50 C Radiator front area m 2 1.2 1.2 1.2 1.3 1.2 1.2 1.2 1.3 Coolant pump flow dm 3 /min 300 300 300 300 360 360 360 360 Fan type Pusher Pusher Pusher Pusher Pusher Pusher Pusher Pusher Ø mm 912 912 912 912 912 912 912 912 power losses kw 11 11 11 11 11 11 11 11 speed ratio 1:1 1:1 1:1 1:1 1:0.8 1:0.8 1:0.8 1:0.8 Air flow free air flow m 3 /s 8.0 8.0 8.0 8.0 7.8 7.8 7.8 7.8 pressure reserve mm Wc 26 22 20 26 23 19 16 26 16 Part No. 1 588 879 Scania Industrial & Marine Engines 2007:1
Latest modification date: 060701 Technical data and cooling equipment recommendation DC12 59A, order ref 10-34A 1500 r/min PRP ESP Gross power kw 399 437 kva* 451 501 Specific fuel consumption g/kwh full load 201 199 3/4 load 208 207 1/2 load 207 207 Heat rejection kw to cooling water 160 174 to exhaust gas 287 307 to charge air 78 86 to surrounding air 36 39 Air consumption kg/min 30 32 Air temperature before charge air cooler C 203 215 Air temperature after charge air cooler C 52 54 Fall of pressure, charge air cooler Bar 0.10 0.12 Exhaust flow kg/min 32 33 Exhaust temperature C 559 578 *The kva range is calculated with the recommended fan for +35 C air-on temperature to cooling system including the fan power losses at a generator efficiency common to the market. For further information see General, sect. 2. 1500 r/min PRP ESP Air-on temp. Air-on temp. 35 C 50 C 35 C 50 C Radiator front area m 2 1.2 1.3 1.3 1.3 Coolant pump flow dm 3 /min 300 300 300 300 Fan type Pusher Pusher Pusher Pusher Ø mm 912 912 912 912 power losses kw 11 11 11 11 speed ratio 1:1 1:1 1:1 1:1 Air flow free air flow m 3 /s 8.0 8.0 8.0 8.0 pressure reserve mm Wc 20 26 22 16 2007:1 Scania Industrial & Marine Engines Part No. 1 588 879 17
Latest modification date: 051201 Technical data and cooling equipment recommendation DC12 56A, order ref 10-10A 1800 r/min PRP ESP Gross power kw 273 300 kva* 305 336 Specific fuel consumption g/kwh full load 215 212 3/4 load 221 219 1/2 load 232 230 Heat rejection kw to cooling water 103 106 to exhaust gas 232 249 to charge air 71 78 to surrounding air 26 28 Air consumption kg/min 31 32 Air temperature after charge air cooler C 45 47 Fall of pressure, charge air cooler Bar 0.08 0.08 Exhaust flow kg/min 32 33 Exhaust temperature C 438 446 *The kva range is calculated with the recommended fan for +35 C air-on temperature to cooling system including the fan power losses at a generator efficiency common to the market. For further information see General, sect. 2. 1800 r/min PRP ESP Air-on temp. Air-on temp. 35 C 50 C 35 C 50 C Radiator front area m 2 1.3 1.3 1.3 1.3 Coolant pump flow dm 3 /min 350 350 350 350 Fan type Pusher Pusher Pusher Pusher Ø mm 912 912 912 912 power losses kw 11 11 11 11 speed ratio 1:0.8 1:0.8 1:0.8 1:0.8 Air flow free air flow m 3 /s 7.8 7.8 7.8 7.8 pressure reserve mm Wc 55 50 50 44 18 Part No. 1 588 879 Scania Industrial & Marine Engines 2007:1
Latest modification date: 051201 Technical data and cooling equipment recommendation DC12 56A, order ref 10-11A 1800 r/min PRP ESP Gross power kw 300 316 kva* 336 355 Specific fuel consumption g/kwh full load 212 209 3/4 load 219 218 1/2 load 230 228 Heat rejection kw to cooling water 106 107 to exhaust gas 249 257 to charge air 78 82 to surrounding air 28 29 Air consumption kg/min 32 33 Air temperature after charge air cooler C 47 48 Fall of pressure, charge air cooler Bar 0.08 0.09 Exhaust flow kg/min 33 34 Exhaust temperature C 446 451 *The kva range is calculated with the recommended fan for +35 C air-on temperature to cooling system including the fan power losses at a generator efficiency common to the market. For further information see General, sect. 2. 1800 r/min PRP ESP Air-on temp. Air-on temp. 35 C 50 C 35 C 50 C Radiator front area m 2 1.3 1.3 1.3 1.3 Coolant pump flow dm 3 /min 350 350 350 350 Fan type Pusher Pusher Pusher Pusher Ø mm 912 912 912 912 power losses kw 11 11 11 11 speed ratio 1:0.8 1:0.8 1:0.8 1:0.8 Air flow free air flow m 3 /s 7.8 7.8 7.8 7.8 pressure reserve mm Wc 50 44 45 39 2007:1 Scania Industrial & Marine Engines Part No. 1 588 879 19
Latest modification date: 051201 Technical data and cooling equipment recommendation DC12 56A, order ref 10-12A 1800 r/min PRP ESP Gross power kw 316 337 kva* 355 379 Specific fuel consumption g/kwh full load 209 204 3/4 load 218 216 1/2 load 228 226 Heat rejection kw to cooling water 107 110 to exhaust gas 257 264 to charge air 82 84 to surrounding air 29 30 Air consumption kg/min 33 33 Air temperature after charge air cooler C 48 48 Fall of pressure, charge air cooler Bar 0.09 0.09 Exhaust flow kg/min 34 34 Exhaust temperature C 451 457 *The kva range is calculated with the recommended fan for +35 C air-on temperature to cooling system including the fan power losses at a generator efficiency common to the market. For further information see General, sect. 2. 1800 r/min PRP ESP Air-on temp. Air-on temp. 35 C 50 C 35 C 50 C Radiator front area m 2 1.3 1.3 1.3 1.3 Coolant pump flow dm 3 /min 350 350 350 350 Fan type Pusher Pusher Pusher Pusher Ø mm 912 912 912 912 power losses kw 11 11 11 11 speed ratio 1:0.8 1:0.8 1:0.8 1:0.8 Air flow free air flow m 3 /s 7.8 7.8 7.8 7.8 pressure reserve mm Wc 50 44 45 39 20 Part No. 1 588 879 Scania Industrial & Marine Engines 2007:1
Latest modification date: 051201 Technical data and cooling equipment recommendation DC12 56A, order ref 10-13A 1800 r/min PRP ESP Gross power kw 337 359 kva* 379 405 Specific fuel consumption g/kwh full load 204 204 3/4 load 216 215 1/2 load 226 225 Heat rejection kw to cooling water 110 115 to exhaust gas 264 281 to charge air 84 91 to surrounding air 30 32 Air consumption kg/min 33 34 Air temperature after charge air cooler C 48 50 Fall of pressure, charge air cooler Bar 0.09 0.09 Exhaust flow kg/min 34 35 Exhaust temperature C 457 468 *The kva range is calculated with the recommended fan for +35 C air-on temperature to cooling system including the fan power losses at a generator efficiency common to the market. For further information see General, sect. 2. 1800 r/min PRP ESP Air-on temp. Air-on temp. 35 C 50 C 35 C 50 C Radiator front area m 2 1.3 1.3 1.3 1.3 Coolant pump flow dm 3 /min 350 350 350 350 Fan type Pusher Pusher Pusher Pusher Ø mm 912 912 912 912 power losses kw 11 11 11 11 speed ratio 1:0.8 1:0.8 1:0.8 1:0.8 Air flow free air flow m 3 /s 7.8 7.8 7.8 7.8 pressure reserve mm Wc 45 39 39 33 2007:1 Scania Industrial & Marine Engines Part No. 1 588 879 21
Latest modification date: 051201 Technical data and cooling equipment recommendation DC12 56A, order ref 10-14A 1800 r/min PRP ESP Gross power kw 359 381 kva* 405 430 Specific fuel consumption g/kwh full load 204 205 3/4 load 215 214 1/2 load 225 223 Heat rejection kw to cooling water 115 121 to exhaust gas 281 301 to charge air 91 99 to surrounding air 32 34 Air consumption kg/min 34 35 Air temperature after charge air cooler C 50 51 Fall of pressure, charge air cooler Bar 0.09 0.09 Exhaust flow kg/min 35 36 Exhaust temperature C 468 483 *The kva range is calculated with the recommended fan for +35 C air-on temperature to cooling system including the fan power losses at a generator efficiency common to the market. For further information see General, sect. 2. 1800 r/min PRP ESP Air-on temp. Air-on temp. 35 C 50 C 35 C 50 C Radiator front area m 2 1.3 1.3 1.3 1.3 Coolant pump flow dm 3 /min 350 350 350 350 Fan type Pusher Pusher Pusher Pusher Ø mm 912 912 912 912 power losses kw 11 11 11 11 speed ratio 1:0.8 1:0.8 1:0.8 1:0.8 Air flow free air flow m 3 /s 7.8 7.8 7.8 7.8 pressure reserve mm Wc 39 33 33 27 22 Part No. 1 588 879 Scania Industrial & Marine Engines 2007:1
Latest modification date: 051201 Technical data and cooling equipment recommendation DC12 56A, order ref 10-15A 1800 r/min PRP ESP Gross power kw 381 403 kva* 430 456 Specific fuel consumption g/kwh full load 205 207 3/4 load 214 211 1/2 load 223 222 Heat rejection kw to cooling water 121 131 to exhaust gas 301 323 to charge air 99 107 to surrounding air 34 36 Air consumption kg/min 35 36 Air temperature after charge air cooler C 51 52 Fall of pressure, charge air cooler Bar 0.09 0.09 Exhaust flow kg/min 36 37 Exhaust temperature C 438 500 *The kva range is calculated with the recommended fan for +35 C air-on temperature to cooling system including the fan power losses at a generator efficiency common to the market. For further information see General, sect. 2. 1800 r/min PRP ESP Air-on temp. Air-on temp. 35 C 50 C 35 C 50 C Radiator front area m 2 1.3 1.3 1.3 1.3 Coolant pump flow dm 3 /min 350 350 350 350 Fan type Pusher Pusher Pusher Pusher Ø mm 912 912 912 912 power losses kw 11 11 11 11 speed ratio 1:0.8 1:0.8 1:0.8 1:0.8 Air flow free air flow m 3 /s 7.8 7.8 7.8 7.8 pressure reserve mm Wc 33 27 26 20 2007:1 Scania Industrial & Marine Engines Part No. 1 588 879 23
Latest modification date: 060701 Basic dimensions DC12 Function of xyz-coordinates is found in Equipment data. 1. Fuel inlet (insert conn. for plastic pipe Ø12 mm) 2. Fuel return (insert conn. for plastic pipe Ø12 mm) x -303 y -213 z +137 x -774 y -300 z +400 3. Air intake (Ø101.6 mm) x -584 y +294 z +627 4. Exhaust outlet x -830 y +294 z +627 5. Connection to charge air cooler x -648 y +112 z +734.5 6. Connection from charge air cooler x -1298 y +225 z +625 7. Water inlet (Ø57 mm) x -1261.5 y +365 z +79 8. Water outlet (Ø57 mm) x -1111 y +278 z +464 9. Oil filler x -1082 y -71 z +688 10. Oil dipstick 11. Oil drain plug x -635 y -58 z -437 12. Drain tap for coolant 13. Conn. for engine speed sensor (2x) 14. To cab heater inlet. (M22 x 1.5) 15. From cab heater outlet. (M22 x 1.5) 16. Oil pressure sensor 17. Connection for coolant temperature sensor/monitor (2 x M14 x 1.5) 18. Connection for expansion tank, for venting. (pipe Ø10 mm) 19. Connection for expansion tank (pipe Ø32 mm) x -1177 y +287 z +337 16 x+ x x- 2 14 11 3 17 10 1 4 9 z- z z+ x- x x+ 8 19 15 7 12 18 5 y+ y y- 13 z- z z+ 6 x- x x+ y- y y+ 24 Part No. 1 588 879 Scania Industrial & Marine Engines 2007:1
Optional design 27.5 Dimensional drawing DC12 Latest modification date: 060701 Optional design 402 394.5 Drawing No. 1 721 515 This sketch is intended only as general sales information and must not be used for any installation purposes. See also General * The values for center of gravity applies for engines with standard equipment including coolant. Cooling equipment such as fan, fanring and protective grille are not included. ~0* ~210* 379 365.5 (2x) 69,5 355±5 355±5 (2x) 1130 For removal of oil pan, min 692 ~610* 387 360 437 2007:1 Scania Industrial & Marine Engines Part No. 1 588 879 25
Latest modification date: 070301 Equipment list Ref Description Requirements Drw No. Remark 10J PACKING -01 Packing on pallet with plastic covering 25A CABLE HARNESS EMS - B1 (6.3m) -00 S Without, but with connector kit B1 1 737 283-01 O With 1 845 822 25C LEVEL MONITOR -00 S Without -01 O 1-pole, normally open Req. radiator Req. 28F-01, -02, -03 or -04 Not with 74-11 -02 O 2-pole, normally closed. Req. 74-11 Req. 28F-01, -02, -03 or -04-04 O 2-pole, normally closed. Req. 28F-01, -02, -03 or -04 Delivered separately -05 O Prepared for level monitor, Req. 28F-01, -02, -03 or -04 normally open. -06 O Prepared for level monitor, Req. 28F-01, -02, -03 or -04 normally closed. 25D STARTER -00 O Without -01 S 1-pole, 5.5 kw 1 447 911-02 O 1-pole, 6.7 kw 1 358 639 25E ALTERNATOR -00 O Without -01 S 1-pole, 65A 1 394 969-02 O 1-pole, 100A 1 516 176-03 O 2-pole, 65A 1 397 038 25F ENGINE HEATER -00 S Without -01 O 1100 W / 220 V, plug in type 1 412 624-02 O 500 W / 220 V, external 1 407 215-03 O 1500 W / 220 V, external 1 407 215 26A FINE TUNE POTENTIOMETER -00 S Without -01 O With Req. 26B-01, -02 26B COORDINATOR -00 S Without -01 O With, incl. connector kit Req. 26K-01, -02, -03 or -04 1 505 545-02 O With, incl. cable harness and connector,3m 26G INSTRUMENT PANEL -00 S Without -05 O Instrument kit, containing gauges for oil pressure and coolant temp. monitoring Req. 26K-01, -02, -03 or -04 1 505 545 26 Part No. 1 588 879 Scania Industrial & Marine Engines 2007:1
Ref Description Requirements Drw No. Remark 26K COORDINATOR SETTINGS -00 S Without -01 O Fine tune potentiometer active, without alarm at 0 rpm -02 O Fine tune potentiometer active, with alarm at 0 rpm -03 O Fine tune potentiometer inactive, with alarm at 0 rpm -04 O Fine tune potentiometer inactive, without alarm at 0 rpm 28B ENGINE TEMP. REACTION (EMS parameter setting) -01 S Only alarm (default value) Note! -02 O Torque reduction on low limit Alarm is always included regardless of option. -03 O Engine stop on high limit Override possibility refer to engine stop -04 O Engine stop on high limit and torque reduction on low limit only, not torque reduction. -05 O Engine stop on high limit (with override possibility) -06 O Engine stop on high limit (with override possibility) and torque reduction on low limit 28C TEMP. LIMIT HIGH (EMS parameter setting) -01 O 95 C Note! It is not possible to choose a lower -02 O 96 C limit for the temp. limit high value (price ref. 28C) than the temp. limit low value -03 O 97 C (price ref. 28D). -04 O 98 C The high temp limit value must be -05 O 99 C identical or above the low temp. limit -06 O 100 C value. -07 O 101 C -08 O 102 C -09 O 103 C -10 O 104 C -11 S 105 C (default value) S = Standard - O = Optional. For illustrations and technical data of references, see Equipment data section 7. 2007:1 Scania Industrial & Marine Engines Part No. 1 588 879 27
Ref Description Requirements Drw No. Remark 28D TEMP. LIMIT LOW (EMS parameter setting) -01 O 85 C Note! It is not possible to choose a higher -02 O 86 C limit for the temp. limit low (price ref. 28D) than the temp. limit high value -03 O 87 C (price ref. 28C). -04 O 88 C The low temp. limit value must be -05 O 89 C identical or below the high temp limit -06 O 90 C value. -07 O 91 C -08 O 92 C -09 O 93 C -10 O 94 C -11 S 95 C (default value) -12 O 96 C -13 O 97 C -14 O 98 C -15 O 99 C -16 O 100 C -17 O 101 C -18 O 102 C -19 O 103 C -20 O 104 C 28E LOW OIL PRESSURE REACTION (EMS parameter setting) -01 S Only alarm (default value) -02 O Torque reduction, ~30% -03 O Engine stop -04 O Engine stop with override 28F LOW COOLANT LEVEL REACTION (EMS parameter setting) -00 S Without (default value) -01 O Only alarm Req. 25C-01, -02, -04, -05 or -06 (level monitor) -02 O Torque reduction, ~30% as ref. 28F-01-03 O Engine stop as ref. 28F-01 S = Standard - O = Optional. For illustrations and technical data of references, see Equipment data section 7. 28 Part No. 1 588 879 Scania Industrial & Marine Engines 2007:1
Ref Description Requirements Drw No. Remark 28H DROOP SETTING (EMS parameter setting) -01 O 0% The droop setting value is defined as how -02 O 0.5% much the engine speed increases from full load to zero load, in % in relation to -03 O 1.0% nominal speed. -04 O 1.5% -05 O 2.0% Mathematically it can be expressed as: -06 O 2.5% High _ Nominal -07 O 3.0% Speed droop % = idling speed x100 Nominal speed -08 O 3.5% -09 S 4.0% (default value) Example: -10 O 4.5% _ 1560 1500-11 O 5.0% 4 % = 1500 x100-12 O 5.5% -13 O 6.0% -14 O 6.5% -15 O 7.0% -16 O 7.5% -17 O 8.0% -18 O 8.5% -19 O 9.0% -20 O 9.5% -21 O 10.0% 28I GOVERNOR SETTING (EMS parameter setting) -01 S Normal (default value) Note! The optional serttings 28I-02 and - -02 O Soft 28I-03 should not be chosen without consulting after sales services, these -03 O Stiff options may only come into question after tests have been made at the site. 28J RAMP START DELAY (EMS parameter setting) -01 S 0 seconds (default value) At start this is the time the engine speed -02 O 1 seconds shall remain at low idle speed before starting the ramp up to nominal -03 O 2 seconds operational speed. -04 O 3 seconds -05 O 4 seconds -06 O 5 seconds -07 O 10 seconds -08 O 20 seconds -09 O 30 seconds -10 O 60 seconds -11 O 90 seconds -12 O 120 seconds 28K RAMP UP RATE (EMS parameter setting) -01 O 100 rpm / seconds This is the rate by which the engine speed -02 O 200 rpm / seconds ramps up, starting from low idle up to nominal operational speed after the delay -03 O 300 rpm / seconds value defined in Ramp start delay -04 O 400 rpm / seconds (Price ref. 28J) -05 S 500 rpm / seconds (default value) S = Standard - O = Optional. For illustrations and technical data of references, see Equipment data section 7. 2007:1 Scania Industrial & Marine Engines Part No. 1 588 879 29
Ref Description Requirements Drw No. Remark 28N LOW IDLE SPEED (EMS parameter setting) -02 O 500 rpm -03 O 550 rpm -04 O 600 rpm -05 O 650 rpm -06 O 700 rpm -07 O 750 rpm -08 O 800 rpm -09 O 850 rpm -10 O 900 rpm -11 O 950 rpm -12 S 1000 rpm (default value) -13 O 1050 rpm 28O THROTTLE SETTINGS (EMS parameter setting) -06 S Nominal speed 1500 / 1800 rpm (default value) -07 O Fine tune of nominal speed always active Note! price ref. 28O-07 is intended for customers that wishes to mount a potentiometer directly to the EMS for fine tuning of the nominal engine speed. 28Q EMS CONTROLLED STARTER (EMS parameter setting) -00 O Without Note! if both starter and alternator are -01 S With (default value) specified, the control option must be controlling both or controlling none, e.g. 28Q-00 + 28R-00 or 28Q-01 + 28R-01 28R EMS CONTROLLED ALTERNATOR (EMS parameter setting) -00 O Without Note! if both starter and alternator are -01 S With (default value) specified, the control option must be controlling both or controlling none, e.g. 28Q-00 + 28R-00 or 28Q-01 + 28R-01 45 FLYWHEEL -15 S 14, pilot hole Ø 80mm 1 390 317 46 FLYWHEEL HOUSING -01 S Measurements according to SAE1 1 403 464 Material: Silumin 49 ENGINE SUSPENSION -01 S Fixed suspension, low 1 402 865 Front brackets only -19 O Fixed suspension, low Not with 51-14 and 51-47 1 402 865-21 O Fixed suspension, power pack type 1 402 865-22 O Fixed suspension, power pack type 1 402 865 Front brackets only -25 O Stiff rubber suspension, low Not with 51-14 and 51-47 1 402 865-26 O Stiff rubber suspension, low 1 402 865 Front brackets only -27 O Stiff rubber suspension, 1 402 865 power pack type -28 O Stiff rubber suspension, power pack type 1 402 865 Front brackets only S = Standard - O = Optional. For illustrations and technical data of references, see Equipment data section 7. 30 Part No. 1 588 879 Scania Industrial & Marine Engines 2007:1
Ref Description Requirements Drw No. Remark 51 AIR CLEANER -01 S Without -14 O Light duty with paper insert and rain 1 388 470 For mounting on flywheel housing protection cap. Filter area 10.6 m 2-25 O Light duty with paper insert and rain 1 399 298 For separate mounting protection cap. Filter area 10.6 m 2-45 O Medium duty with paper insert, precleaner and rain protection cap. Filter area 16 m 2 1 399 298 For separate mounting -47 O Medium duty with paper insert, precleaner and rain protection cap. Filter area 16 m 2 1 388 470 For mounting on flywheel housing 51A SAFETY CARTRIDGE FOR AIR CLEANER -00 S Without -01 O With safety cartridge Req. 51-45 or 51-47 1 399 298 56 EXHAUST BEND -00 S Without, Req. 57-00 1 383 334 but with turbo mounted flange -21 O 90 bend, adjustable direction Not with 57-00 1 383 334 57 EXHAUST FITTINGS -00 S Without -41 O Flange, Ø 114 mm Req. 56-21 1 383 334-42 O Flange, Ø 130 mm Req. 56-21 1 383 334-43 O Flange, Ø 155 mm Req. 56-21 1 383 334-51 O Compensator and flange, Ø 114 mm Req. 56-21 1 383 334-52 O Compensator and flange, Ø 130 mm Req. 56-21 1 383 334-53 O Compensator and flange, Ø 155 mm Req. 56-21 1 383 334 58 SILENCER, shipped loose -00 S Without -31 O Truck type with clamps, Ø 115 mm 1 331 676-32 O Truck type with flanges, Ø 115 mm 1 331 676-33 O Truck type with flanges, Ø 130 mm 1 331 676-34 O Truck type with flanges, Ø 155 mm 1 331 676-36 O Industrial type with flanges, 1 379 683 straight outlet Ø 130 mm -37 O Industrial type with flanges, 1 379 683 straight outlet Ø 155 mm 60 OIL SUMP -05 S Deep front oil sump 1 422 908 Oil dipstick on left or right hand side. Drain plug on low left hand side. -06 O Deep front oil sump 1 422 908 Oil dipstick on right hand side. Drain plug on low left hand side. Equipped for checking oil level with running engine. -07 O Low oil sump 1 422 908 Oil dipstick on left or right hand side. Drain plug on low right hand side. S = Standard - O = Optional. For illustrations and technical data of references, see Equipment data section 7. 2007:1 Scania Industrial & Marine Engines Part No. 1 588 879 31
Ref Description Requirements Drw No. Remark 60A OIL DIPSTICK -01 S On right hand side in oil pan 1 407 418-02 O On right hand side in engine block Not with 60-07 1 407 418 61 OIL FILLER -01 S In valve cover, cyl. 1 1 403 464-01A O In valve cover, cyl. 5-02 O On left hand side in engine block Not with 60A-02 1 407 419-03 O In valve cover, (cyl. 1) and on left hand side in engine block Not with 60-07 1 407 419-03A O In valve cover, (cyl. 5) and on left Not with 60-07 hand side in engine block 62 OIL DRAINING -01 S Magnetic drain plug in oil pan 1 403 464-01A O Magnetic drain plug in oil pan, Req. 60-07 1 422 908 left hand side -01B O Magnetic drain plug in oil pan, right hand side Req. 60-07 1 422 908-10 O Hand pump, right hand side 1 407 848 (delivered loose) -11 O Hand pump, left hand side 1 407 848 (delivered loose) -12 O Hand pump, right hand side. 1 407 848 (delivered loose) Incl. 3-way cock 66 CRANKSHAFT PULLEY -00 S Without -14 O With 2 extra grooves, Ø 260 mm Req. fan ratio 1:1.08 1 404 595-15 O With 2 extra grooves, Ø 192 mm Req. fan ratio 1:1.08 1 404 595-17 O For poly-v belt, Ø 260 mm Req. fan ratio 1:1.08 1 404 595 72 FAN -01 S Without fan and fan drive Req. 74-01, -02-28 O Prepared for fan, ratio 1:1 Req. 74-01, -02 1 386 303 Req. 25E-01, -02 or -03-32 O Prepared for fan, ratio 1:0.8 Req. 74-01, -02 1 386 303 Req. 25E-01, -02 or -03-35 O Ø 787 mm, pusher, ratio 1:1.08 Req. 92A-00 1 386 303-36 O Ø 912 mm, puller, ratio 1:0.8 Req. 25E-01, -02 or -03 1 386 303-37 O Ø 912 mm, pusher, ratio 1:0.8 Req. 25E-01, -02 or -03 1 386 303-38 O Ø 912 mm, pusher (plastic), Req. 25E-01, -02 or -03 1 386 303 ratio 1:0.8-39 O Ø 912 mm, puller, ratio 1:1 Req. 25E-01, -02 or -03 1 386 303-40 O Ø 912 mm, pusher, ratio 1:1 Req. 25E-01, -02 or -03 1 386 303-41 O Ø 912 mm, pusher (plastic), ratio 1:1 Req. 25E-01, -02 or -03 1 386 303 S = Standard - O = Optional. For illustrations and technical data of references, see Equipment data section 7. 32 Part No. 1 588 879 Scania Industrial & Marine Engines 2007:1
Ref Description Requirements Drw No. Remark 74 CHARGE AIR COOLER AND RADIATOR -01 S Without charge air cooler and radiator. 1 721 515 Charge air pipe pointing upwards -02 O Without charge air cooler and radiator. Charge air pipe pointing downwards 1 721 515-11 O Charge air cooler and radiator 1.3 m 2 incl. fan cover, side supports, protective grating and expansion tank -26 O Charge air cooler and radiator 1.0 m 2 incl. fan cover and expansion tank -28 O Charge air cooler and radiator 1.0 m 2 incl. fan cover, side supports, protective grating and expansion tank -35 O Charge air cooler and radiator 1.2 m 2 incl. fan cover and expansion tank -36 O Charge air cooler and radiator 1.2 m 2 incl. fan cover, side supports, protective grating and expansion tank 76 FAN RING -00 S Without Req. 72-38 or 72-41 Req. 76-00 -21 O Fan ring with sealing Not with 72-01, -28 or -32 Not with 74-11 -22 O Fan ring with sealing, protective grating and drive belt cover 1 722 031 Req. 72-35 1 407 843 Note! this option is not available for DC12 52A, DC12 53A and DC12 56A Req. 72-35 1 407 844 Note! this option is not available for DC12 52A, DC12 53A and DC12 56A Not with 72-35 1 413 544 Note! this option is not available for DC12 52A, DC12 53A and DC12 56A Not with 72-35 1 413 545 Note! this option is not available for DC12 52A, DC12 53A and DC12 56A Not with 72-01, -28 or -32 Not with 74-11 1 407 845 1 407 846 1 407 845 1 407 846 for fan Ø 787 for fan Ø 912 for fan Ø 787 for fan Ø 912 91 SIDE MOUNTED POWER TAKE-OFF -00 S Without -13 O SAE B (J744), 2-hole, 13 teeth. Gear ratio 1:1.19, counter clockwise 1 784 540 Note! max. torque 400 Nm -13A O Prepared for side mounted power 1 376 355 take-off -15 O SAE A (J744), 2-hole, 9 teeth. Gear ratio 1:1.7, counter clockwise Req. 93-00 Note! max. torque 100 Nm (continuous) max. torque 125 Nm (intermittent) 92 AIR COMPRESSOR -00 S Without -01 O AC-Compressor 2-cylinder, water cooled incl. unloader 1 520 638 Note! for information on air capacity, see section 7 92A AC COMPRESSOR -00 S Without -01 O With Not with 72-34 and 72-35 1 404 227 93 HYDRAULIC PUMP -00 S Without -12 O Capacity: 16 l/min at 150 bar int., 1 757 131 Note! Without pressure reduction valve 25-30 bar cont. -13 O Capacity: 22 l/min at 150 bar int., 25-30 bar cont. 1 757 131 Note! Without pressure reduction valve S = Standard - O = Optional. For illustrations and technical data of references, see Equipment data section 7. 2007:1 Scania Industrial & Marine Engines Part No. 1 588 879 33
Ref Description Requirements Drw No. Remark 95 DRIVE BELT COVER -01 S Without -04 O Drive belt cover (with alternator) Drive belt cover (without alternator) 96C STUDS IN FLYWHEEL HOUSING -00 O Without -01 S With 98B CORROSION PROTECTION -00 S Without -01 O 10 litre corrosion inhibitor 98C FUEL PRE-FILTER Req. 72-01 1 432 956 1 431 749 Note! for engines without fan and fan drive only. -00 O Without Note! Requires a pre-filter from an external manufacturer. If no filter is mounted the engine warranty is not valid. -01 S Fuel pre-filter with water separator 1 407 701-02 O fuel pre-filter with water separator 1 407 701 and heater 99E COLD START EQUIPMENT -00 S Without -01 O Cold start aid (flame start) 1 726 482 99L CRANKCASE VENTILATION -31 S Crankcase ventilation Open, direction downwards -36 O Crankcase ventilation 1 405 725 In valve cover, for external connection -38 O Crankcase ventilation Req. 61-01A or 61-03A 1 405 359 Internal ventilation (closed) 99N SCANIA INTERNATIONAL SERVICE GUIDE (SIS) -00 S Without -01 O With 99P EXTRA OPERATOR S MANUAL -01 S Without -02 O Extra operator s manual x1 Available languages are: -03 O Extra operator s manual x2 Brazilian / Portuguese, English, Finnish, French, German, Italian, Spanish and Swedish. Note! One copy is already included free of charge at delivery, if a preferred language is not specified when ordering the operator s manual will be delivered in English. 99Q SPARE PARTS CATALOGUE -00 S Without -31 O With spare parts catalogue x1-32 O With spare parts catalogue x2-33 O With spare parts catalogue x3 S = Standard - O = Optional. For illustrations and technical data of references, see Equipment data section 7. 34 Part No. 1 588 879 Scania Industrial & Marine Engines 2007:1
This page has intentionally been left empty. 2007:1 Scania Industrial & Marine Engines Part No. 1 588 879 35
This page has intentionally been left empty. 36 Part No. 1 588 879 Scania Industrial & Marine Engines 2007:1
This page has intentionally been left empty. 2007:1 Scania Industrial & Marine Engines Part No. 1 588 879 37
Ideas and opinions about this book? The ambition with this book is to give you all the information you may need working with Scania engines. However, there can be parts of this book that could be described in another way or some information you wish to be added. When you have suggestions for improvements, or you find faulty information, please copy this page, write down your opinions and send by telefax or mail to the adress below. Your remarks may help us to further improve the following editions. Thank you in advance for your co-operation Sender: Suggestion / Remark: Mail to Scania CV AB Industrial and Marine Engines Dept. KEMY S-151 87 Södertälje, Sweden Telefax Sales +46-8 55 38 29 93 (int) 08 55 38 29 93 (nat) After sales +46-8 55 38 98 12 (int) 08 55 38 98 12 (nat) Telephone +46-8 55 38 10 00 (int), 08 55 38 10 00 (nat) 38 Part No. 1 588 879 Scania Industrial & Marine Engines 2007:1