PerformancePipe.com YELLOWSTRIPE 8300 BIMODAL HDPE PIPE DATA SHEET Yellowstripe 8300 Pipe meets or exceeds: ASTM D2513 CAN/CSA-B137.4 UPC ASTM D3350, cell classification PE445574C and PE445576C PPI TR-4 designation PE4710 (PE3408) and PE100 Yellowstripe 8300 Pipe for: Natural Gas Distribution, LPG and Propane Gas Distribution, Yard Gas Iron Pipe OD (IPS) ½ to 24, Copper Tube OD (CTS) ½ to 1 ¼ Coils available up through 6 Bulletin: PP109 / Sep 2014 Outdoor Storage up to Ten (10) years per ASTM D2513 NOMINAL PIPE PROPERTIES (1) UNIT TEST METHOD VALUE Density gms / cm 3 ASTM D1505 0.961 (black) Melt Index (HLMI) 190ºC / 21.6 kg gms / 10 minutes ASTM D1238 9.0 Hydrostatic Design Basis 73º F (23º C) psi ASTM D2837 1600 Hydrostatic Design Basis 140º F (60º C) psi ASTM D2837 1000 Minimum Required Strength (MRS) @ 20ºC (68ºF) Mpa (psi) ISO 9080 >10 (>1450) Rapid Crack Propagation (3) Bar (psi) ISO 13478 >46 bar (>667 psi) Full Scale, 0ºC (32ºF) Color: UV Stabilizer [C] --- ASTM D3350 Min 2% Carbon Black Pipe Test Category --- ASTM D2513 CEE NOMINAL MATERIAL PROPERTIES (1) (2) UNIT TEST METHOD VALUE Flexural Modulus @ 2% Strain psi ASTM D790 140,000 Tensile Strength at Yield Elongation at Break 2 in / min., Type IV Bar 2014 Chevron Phillips Chemical Company LP Performance Pipe, a division of Chevron Phillips Chemical Company LP 5085 W. Park Blvd Suite 500 Plano, TX 75093 Phone: 800-527-0662 Fax: 972-599-7348 psi ASTM D638 Type IV >3500 % ASTM D638 >800 Hardness Shore D ASTM D2240 65 PENT hrs ASTM F1473 >2000 Vicat Softening Temperature ºF ASTM D1525 255 Brittleness Temperature ºF ASTM D746 <-103 Thermal Expansion in / in / ºF ASTM D696 1.0 x 10-4 1. This is not a product specification and does not guarantee or establish specific minimum or maximum values or manufacturing tolerance for material or piping products to be supplied. 2. Values obtained from tests taken from actual piping product may vary from these typical values. 3. Calculated value per correlation equation in ISO 4437 based on S4 test data on 10 DR 11. 4. Melt Index (MI) value determined in accordance with ASTM D3350 Cell Classification is <0.15 gm/10 min at 2.16kg. 5. Melt Index (MI) value determined in accordance with ASTM D3350 Cell Classification is <0.15 gm/10 min at 2.16kg condition. This data sheet provides typical properties for Performance Pipe DriscoPlex pipe and fittings. Before using this product, the user is advised and cautioned to make their own determination and assessment of the safety and suitability of the product for the specific use in question and is further advised against relying on the information contained herein as it may relate to any specific use or application. It is the ultimate responsibility of the user to ensure that the product is suited and the information is applicable to the user s specific application. Chevron Phillips Chemical Company LP does not make, and expressly disclaims, all warranties, including warranties of merchantability or fitness for a particular purpose, regardless of whether oral or written, express or implied, allegedly arising from any usage of any trade or from any course of dealing in connection with the use of information contained herein or the product itself. The user expressly assumes all risk and liability, whether based in contract, tort or otherwise, in connection with the use of the information contained herein or the product itself. Further, information contained herein is given without reference to any intellectual property issues, as well as federal, state or local laws which may be encountered in the use thereof. Such questions should be investigated by the user. The data sheet may change periodically. Visit www.performancepipe.com for the most current data sheet. Page 1 of 1
YELLOWSTRIPE 8300 Series and Dimension Sheet CTS = COPPER TUBE SIZE Outside Diameter Minimum Wall Dimension Ratio MAOP (psig per CFR Part 192 @73.4 F or less) Weight per 100 ft Coil / Joint (feet) Packing Dimensions ID / OD / Width Coils / Joints Per Pallet or Footage s Per 0.062 DR 10.1 4.8 500 30 / 38 / 6 6,000 156,000 1/2.0625 100 or 12 26 0.090 DR 6.9 6.6 1000 30 / 44 / 6 12,000 312,000 3/4 0.875 0.090 DR 9.7 100 9.7 500 30 / 38 / 11 6 3,000 26 78,000 0.090 DR 12.5 89 13 0.101 DR 11.4 100 14 1 1.125 0.102 DR 11.0 100 14 0.121 DR 9.3 123 17 500 30 / 42 / 11 8 4,000 26 104,000 0.125 DR 9.0 125 17 0.161 DR 7.0 125 21 1 1/4 1.375 0.090 DR 15.3 72 16 0.121 DR 11.4 99 21 500 32 / 45 / 14 1/2 6 3,000 24 72,000 48 ft. IPS = IRON PIPE SIZE Dimension Ratio Outside Diameter Minimum Wall MAOP (psig per CFR Part 192 @ 100 F or less) Weight per 100 ft Coil / Joint (feet) Packing Dimensions ID / OD / Width Coils / Joints Per Pallet or Footage s Per 1/2 DR 9.3 0.840 0.090 123 9 500 30 / 44-6 14 7,000 26 182,000 DR 7 0.150 19 125 3/4 DR 9 1.050 0.117 15 500 30 / 44 / 10 7 3,500 26 91,000 DR 11 0.095 100 13 1 DR 9.3 0.141 123 23 1.315 DR 11 0.120 100 20 500 30 / 44 / 12 6 3,000 26 78,000 1 1/4 DR 7 0.237 125 46 1.660 DR 11 0.151 100 31 500 48 / 72 / 7-1/2 12 6,000 7 42,000 DR 7 0.339 125 95 2 DR 9 2.375 0.255 125 75 500 52 / 78 / 13 7 3,500 7 24,500 DR 11 0.216 100 64 40 3 DR 11 3.500 0.318 100 140 500 DR 9 0.500 125 276 40 4 4.500 DR 11 0.409 100 230 500 6 8 12 16 18 DR 9 0.736 125 598 DR 11 6.625 0.602 100 501 DR 13.5 0.491 82 416 DR 9 0.958 125 1013 DR 11 8.625 0.784 100 849 DR 13.5 0.639 82 705 DR 11 1.159 100 1855 DR 15.5 12.750 0.823 71 1357 DR 21 0.607 51 1021 DR 11 1.455 100 2921 16.000 DR 17 0.941 64 1961 DR 11 1.636 100 3697 DR 13.5 18.000 1.333 82 3071 DR 17.0 1.059 64 2482 40 500 soft bundles 70 / 96 / 23 3/4 soft bundles 70 / 93 / 41 soft bundles 84 / 120 / 50 50 4 29 3 13 Upright 2,000 1,160 1,000 520 Upright 14 6 14 6 14 8 48 ft. 28,000 12,000 16,240 6,000 7,280 4,000 40 soft bundles 9 360 10 3,600 40 bulk packs 8 jts/layer 320 6 1,920 40 bulk packs 6 jts/layer 240 5 1,200 Available upon request Other sizes and packaging configurations may be available. Pipe weights are calculated in accordance with PPI TR-7. Performance Pipe, a division of www.performancepipe.com Phone: 800-527-0662 Chevron Phillips Chemical Company LP Fax: 972-599-7348 Bulletin: PP 159 Page 1 of 1 August 2013 Supersedes all previous publications 2012 Chevron Phillips Chemical Company LP
IPS Gas Soft Sided s PERFORMANCE PIPE IPS PRODUCTS SOFT-SIDED BUNDLES (20,40 & 50 Joints) (Note 1) Style Pipe OD Joints Per s Per 20 /40 /50 Joints Per 20 /40 /50 DR 20 Joints 40 Joints 50 Joints 20 / 10 / NA 1,000 / 500 / NA 7 20,000 20,000 N/A 3 Soft 3.500 50 26 / 13 / NA 1,300 / 650 / NA 9 26,000 26,000 N/A 28 / 14 / NA 1,400 / 700 / NA 11-19 28,000 28,000 N/A 22 / 11 / 9 638 / 319 / 261 7 12,760 12,760 13,050 4 Soft 4.500 29 28 / 14 / 11 812 / 406 / 319 9 16,240 16,240 15,950 28 / 14 / 13 812 / 406 / 377 11 16,240 16,240 18,850 28 / 14 / 14 812 / 406 / 406 13.5-19 16,240 16,240 20,300 22 / 11 / 9 286 / 143 / 117 7 5,720 5,720 5,850 6 Soft 6.625 13 28 / 14 / 11 364 / 182 / 143 9 7,280 7,280 7,150' 28 / 14 / 14 364/ 182 / 182 11-19 7,280 7,280 9,100 8 Soft 8.625 9 20 / 10 / 10 180 / 90 / 90 11-19 3,600 3,600 4,500 Note 1: GAS DISTRIBUTION When travelling in states with a 13 6 maximum height restriction shipping 13 or 14 bundles of 3 or 6 may exceed the height restriction unless the trailer height is 58or below (depending on the thickness of the bottom board utilized). Revised: 02/27/2013 Page 1 of 5
IPS Gas Soft Sided s Soft Sided Style: For encasing all straight lengths between 3.500 OD and 8.625 OD. (1) Lumber s and Placement: (a) Will be constructed using 3 x 4 bottom boards for GAS DISTRIBUTION (SERIES 6500-8100-8300).( 3 x 4 boards actually have a thickness of approximately 2.5, not to be less than 2) Hardwood or softwood is acceptable. Grooved boards are preferable, but not mandatory as the banding will create a notch in some soft woods securing the banding in place. (b) The bottom board length requirement is that the bottom board must go past the center point of the outer joints but not extend past the outer edge of the outer joint. IPS Pipe Target Board Length 3 42 (+0.75, -0.00) 4 42 (+0.75, -0.00) 6 42 (+0.75, -0.00) 8 42 (+0.75, -0.00) (c) Bottom boards are spaced at three (3) equidistant locations for twenty-foot (20 ) joints. (d) Bottom boards are spaced at six (6) equidistant locations for forty-foot (40 ) joints. (e) Bottom boards are spaced at seven (7) or eight (8) equidistant locations for fifty-foot (50 ) joints depending on bundling cart and plant. (2) Top Boards: (a) Top boards may be used to increase the stability of 3 to 8 soft bundles at manufacturer s discretion or at the customer s request. (b) Top boards are placed on each end of the bundle, in line with the end bottom board. (Optional middle top boards are acceptable) (c) Top boards may be constructed of 2 X 6 boards. The thickness of the top board should not exceed the thickness of the bottom board. Hardwood or softwood is acceptable. (d) The top board length requirement is that the top board must go past the center point of the outer joints but not extend past the outer edge of the outer joint. IPS Pipe Target Board Length 3 42 (+0.75, -0.00) 4 42 (+0.75, -0.00) 6 42 (+0.75, -0.00) 8 42 (+0.75, -0.00) Revised: 02/27/2013 Page 2 of 5
IPS Gas Soft Sided s (3) Banding: It is important that each band on a soft-side bundle be tightened to the same tension. Air regulated or battery operated banding equipment is acceptable. Use at least one ¾ X.050 or 5/8 X.035 polyester banding per bottom board. If using 5/8 X.035 polyester place one band around pipe between boards. At the plant s discretion one band may please placed around the pipe on each end of the pack to help secure the caps/plugs and to stabilize the pack. (4) Storage: Soft-side bundles must be stacked plumb to prevent leaning. Special care must be taken when staging bundles in storage. Packs may be stacked in the plant yard on lumber to prevent the bottom of the pipe from coming in contact with the ground. (5) Transport: Performance Pipe Transport Strapping Policy (A.10 Pckg EXH2-Strapping Table) establishes minimum requirements regarding the number of trucker straps used by all transportation providers to secure bundles. The policy also contains conditions regarding the tightening of straps after a carrier leaves a Performance Pipe facility. (6) Tarping: All 6500-8100-8300 series bundles may be smoked tarped at least 8 back on top and 8 in front and on sides or full tarped depending on customer request. (7) End Caps: Place ventilated end caps (or plugs) on all 6500-8100-8300 series products. Revised: 02/27/2013 Page 3 of 5
IPS Gas Soft Sided s IPS Soft Sided s (Examples) 3 IPS 4 IPS 50 Joints Per 29 Joints Per 6 IPS 8 IPS 13 Joints Per 9 Joints Per GAS DISTRIBUTION ONLY Revised: 02/27/2013 Page 4 of 5
IPS Gas Soft Sided s IPS Soft Sided Patterns (20, 40 & 50 Joints) Pipe OD Style Height (Note 2) BTM Board Length (Note 1) Joints Per s Per 20 /40 /50 Pattern DR 20 40 50 3 (Note 3) 3.500 Soft 15.093 42 50 20/10/NA 7 1,000 2,000 N/A 26/13/NA 13/12/13/12 9 1,000 2,000 N/A 28/14/NA 11-19 1,000 2,000 N/A 22/11/9 7 580 1,160 1,450 4 4.500 Soft 14.794 42 29 28/14/11 9 580 1,160 1,450 10/9/10 28/14/13 11 580 1,160 1,450 28/14/14 13.5-19 580 1,160 1,450 6 6.625 (Note 3) 8 8.625 Soft 14.862 42 13 Note 1 : Figure is also top board length 22/11/9 7 260 520 650 28/14/11 7/6 9 260 520 650 28/14/14 11-19 260 520 650 Soft 18.594 42 9 20/10/10 5/4 11-19 180 360 450 Note 2 : height determined using 2 ½ thick boards. Note 3 : When travelling in states with a 13 6 maximum height restriction shipping 13 or 14 bundles of 3 or 6 may exceed the height restriction unless the trailer height is 58 or below (depending on the thickness of the bottom board utilized). Revised: 02/27/2013 Page 5 of 5