NAF ProCap Capping valve DN00-70, ANSI -0 PN6, ANSI Class 0 Fk.(0)GB 0.7 Primary characteristics NAF ProCap, Capping valve for automated filling of wood chips to the batch digester in Pulp industries. The design provides a reliable and tight shuttoff valve with long life time, supplied as standard in stainless steel for pressure ratings PN 6 and ANSI Class 0 and in sizes DN00/, DN600/ and DN70/0. The valve has: an unique design using the eccentric hubs to load the seat and provide a tight shutoff an inlet neck that is drilled and tapped to accept direct mounting of the chip chute an outlet flange in std dimension or customized to meet existing digester flange a stainless steel ball segment with welded overlay of Alloy in the seat area Alloy seat has sealed stems with O-rings in PFM that prevent build up and results in an increased life time NAF Turnex high performance pneumatic actuators used for operation and eccentric hub locking device, cylinders in stainless steel with spring to lock the valve for safe operation CE-marked according to Pressure Equipment Directive (PED /68/EU) module H, category III. For module H, category IV contact NAF Application NAF ProCap is a batch digester capping valve for chips filling in a safe and time saving way. Technical specification Material: EN.08 Size range: DN00, 600, 70,, 0 Outlet Flange DN700, 800, 90 8,, 8 or customized Pressure ratings: PN 6 ANSI Class 0 Max differential pressure: 6 bar Face to face: See page Valve design: ANSI B6. and EN 6 Temperature range: Test pressure: Tightness class: -0 - +0ºC, x PN at open valve According to EN 66- Leakage test with gas according to EN 66-, Rate A (no visible leakage) Other technical data will be specified by NAF for each individual application.
Working pressure, differential pressure and temperature The maximum working pressure and temperature in the body depends on pressure class according to respectively flange standards. For EN09-:0, see diagram. Max working pressure (Diagram ) 0 Pressure (P) bar 0 0 0 C 0 C 00 C 0 C 0 C 0 C Temperature (T) C PN6 body ANSI 0 body Max dp (Diagram ) 0 Pressure (P) bar 0 0 0 C 0 C 00 C 0 C 0 C 0 C Temperature (T) C
Material specification (Table ) (standard CF8M version) 9 8 7 9 7 9 7 6 0 0 6 8 8 6 0 6 6 7 7 9 0 8 Item Qty Part Material Body.08 Ball sector.08/alloy Stem, operating.60 Stem, tightening.60 Eccentric hub.60/hard Chrome 6 Eccentric hub.60 7 Seat ring.08/alloy 8 Clamp ring.08 9 Screw A-80 0 8 Screw A-70 Screw A-80 Cover.6 Cover.6 Lock segment.60/hard Chrome Stem bearing PTFE + Stainless steel 6 Stem bearing PTFE + Stainless steel 7 Washer PTFE + Stainless steel 8 Pin.60 9 Pin washer.60 Cyl. pin.60 Screw A-80 Jammer plate.6 Item Qty Part Material Hub.60/Hard Chrome Cylinder Piston.60 6 Distance block.6 7 Lid.6 8 Actuator plate.6 9 Key A 0 Key A 6 Screw A-80 6 Nut A-80 Screw A-80 Screw A-80 Gasket Graphite 6 Eccentric hub bearing TFE + Stainless steel 7 Screw A-80 8 Screw A-80 9 O-ring H-ELAST 0 O-ring H-ELAST O-ring H-ELAST O-ring H-ELAST O-ring H-ELAST Thread insert A-70
NAF ProCap Capping valve Application NAF ProCap capping valve for automated filling of wood chips to the batch digester in pulp industries. A unique design using the eccentric hubs to load the seat and provide a tight shutoff. Wood chips Capping valve Batch digester Blow valve
Dimensions and weight A E F D B G C Pneumatic actuators for DN00/700 are NAF 7990-0 and 7990- Pneumatic actuators for DN600/800 are NAF 7990-80 and 7990-0 Pneumatic actuators for DN70/90 are NAF 7990-80 and 7990-0 (Table ) DN Size A B C D E F G Weight Kg 00/700 /8 60 60 90 70 70 96 69 80 600/800 / 860 79 08 7 8 90 796 0 70/90 0 /8 080 0 00 7 90 700 Dimensions in mm NOTE: The outlet flange and the face-to-face of the valve can be customized to match an existing installation.
Limit switch box for Locking device 0 6 8 6 7 7 7 6 9 8 9 LIMIT SWITCHES LOCKED UNLOCKED BROWN BLUE BROWN BLUE Art. 9 7 0 SINGLE-POLE SWITCH FUNCTION: ACTIVATED: CONTACT -, - 6
NAF ProCap Capping valve NAF Control Valves Materials (Table ) Item Qty Part Material Cylinder Stainless Box ABS-plastic Limit switch Plastic (PBA) Terminal block Plastic (Gemin) Cable gland Polyamide 6 Nut A 7 Silencer Brass 9 Plate.0 0 Washer.0 Mounting plate.0 Mounting nut.0 Holder plate.0 Rod bulb.0 7 Screw A 8 Screw A 9 Screw A 6 Screw A Screw A 8 Nut A Nut A 8 Locking nut A Locking nut A 6 Washer A 7
Product code NAF ProCap valves Example: 86 8 9 0-600/800 Code 6. Valve type 86 Batch digester capping valve. Material (body) 8 ASTM A CF8M E ASTM A CG8M. Pressure rating PN6 ANSI 0. Stem seal 9 H-ELAST (same media resistance as EPDM), max t=0 C. Seals Seat rings Seat seal 0 Alloy H-ELAST (same media resistance as EPDM), max t=0 C 6. Size inlet / outlet DIN-version ANSI-version DN Size 00 00/700 /8 /8 600 600/800 / / 70 70/90 0/8 0 /8 Actuators to be ordered separately. NAF AB SE-8 87 Linköping Sweden Telephone +6 6 00 Facsimile +6 60 e-mail salesnaf@flowserve.com Website: www.naf.se 8 ISO 900 Certified We reserve the right to design modifications without prior notice