INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 38137-38714 Accessory HandsFreeLink 2008 ODYSSEY Issue Date JAN 2008 PARTS LIST Attachment Kit P/N 08E02-SHJ-100B trim Fuse label Fuse (2 A) bracket 6 EPT sealers harness 8 Wire ties subharness 4 Self-tapping screw, 3 x 10 mm 2 Washer screws, 4 x 12 mm 2 Double-faced tapes Self-tapping screw retainer Bush Ground bolt Template Rubber bumper 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38137-38714 (0801) 08E02-SHJ-1B00-91 1 of 12
Blue Tooth Kit P/N 08E00-E10-100 Illustration of the Installed on the Vehicle Switch SWITCH CONTOROL UNIT HARNESS Control unit FUSE (2 A) Accessory User's Information Manual 7518071E INSTALLATION TOOL AND SUPPLIES REQUIRED #2 Phillips screwdriver 10 mm Combination wrench 10 mm and 14 mm Socket Pushpin Ratchet 3 mm, 4.5 mm, 6 mm, 9 mm, and 10 mm Drill bit Eye protection (face shield, safety goggles, etc.) File Diagonal cutters Scissors Masking tape Tape measure Cardboard Isopropyl alcohol Shop towel 19 mm Holesaw Drill Utility knife T15 Torx bit Felt-tip pen Plastic trim tool SILTRIMTL10 Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the preset buttons. 2. Disconnect the negative cable from the battery. 2 of 12 AII 38137-38714 (0801) 2008 American Honda Motor Co., Inc. - All Rights Reserved.
3. Disengage eight retaining tabs and remove left and right lens from the roof console. 7. Using a flat-tip screwdriver, push the hook and turn the holder. Remove the holder. S PLASTIC TRIM TOOL SUNVISOR HOLDER SUNGLASS HOLDER (Open.) RIGHT LENS COVER RETAINING TAB LEFT SUNVISOR 2 SCREWS 4 RETAINING TABS LEFT LENS 2 BOLTS 4. Open the sunglass holder. 4 RETAINING TABS 2 BOLTS 5. Remove four bolts and lower the roof console. 6. Disconnect the two vehicle connectors and remove the roof console. 7517010E 8. Disengage two screws and remove the left sunvisor. 9. Pull away the weatherstrip from the left front A- pillar trim. Release the side curtain air bag clip by using the plastic trim tool and remove the left front A-pillar (two clips). PLASTIC TRIM TOOL WEATHERSTRIP SIDE CURTAIN AIR BAG CLIP LEFT FRONT A-PILLAR TRIM CLIP 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38137-38714 (0801) 3 of 12
10. Remove the left front door sill trim (three clips). 12. Attach the fuse label (2 A) to the fuse case of the subharness. LEFT FRONT DOOR SILL TRIM 3 CLIPS FUSE LABEL (2 A) FUSE CASE 7821100B 4301210B 11. Pull away the weatherstrip from the left kick panel. Remove the left kick panel (three clips). 13. Plug the subharness 6-pin connector into the 6-pin opening in the fuse box. WEATHERSTRIP 3 CLIPS LEFT KICK PANEL 4301221B FUSE BOX 6-PIN 7517042E 4 of 12 AII 38137-38714 (0801) 2008 American Honda Motor Co., Inc. - All Rights Reserved.
NOTE: If another accessory is already plugged into the 6-pin connector, remove the dummy connector from the 6-pin connector taped to the subharness. Plug the 6-pin connector from the other accessory harness into the 6-pin connector from the subharness you just unplugged and plug the subharness into the fuse box. FUSE BOX 16. Remove the vehicle bolt (discard) and install the ground bolt with subharness ground terminal as shown. 6-PIN FUSE BOX FUEL OPENER GROUND BOLT BOLT (Discard.) GROUND TERMINAL DUMMY HOOD OPENER 7517051E OTHER ACCESSORY 6-PIN 4319060B 14. Route the subharness to the left front pillar trim opening. 17. Disconnect the vehicle harness 1-pin connector and connect it to the subharness 1-pin connector. HARNESS 1-PIN 1-PIN WIRE TIE HARNESS CLIP GREEN TAPE HARNESS EPT SEALER LEFT FRONT PILLAR TRIM OPENING 15. Route the subharness and secure the harness to the vehicle harness with a wire tie above the vehicle clip as shown. 7517031E EPT SEALER Cut in half. CONNECTION PART 7517072E 18. Connect the subharness 1-pin connector to the vehicle 1-pin connector. 19. Wrap the cut one half of the EPT sealer on the subharness connection part. 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38137-38714 (0801) 5 of 12
20. Secure the subharness to the vehicle harness with a wire tie. 23. Cut the template into template A and template B. PANEL EPT SEALER TEMPLATE A TEMPLATE WIRE TIE TEMPLATE B 7517091E HARNESS 7517061E 21. Using isopropyl alcohol on a shop towel, clean the area where the EPT sealer will attach. Attach a EPT sealer to secure the subharness to the vehicle panel. 22. Secure the subharness to the vehicle harness with three wire tie. 24. Remove the damper (two tapping screws). BUSHES SUNGLASSES HOLDER PIN TAPPING SCREW 3 WIRE TIES 2 RETAINING TABS CAMSET LOCK HARNESS 2 TAPPING SCREWS DAMPER 7517101E 25. Remove the sunglasses holder (tapping screw and vehicle bushes). 26. Remove the pin and remove the camset lock (two retaining tabs). 7517080E 6 of 12 AII 38137-38714 (0801) 2008 American Honda Motor Co., Inc. - All Rights Reserved.
27. Remove the console light from the roof console (four retaining tabs). 29. Attach masking tape to the roof console as shown. MASKING TAPE 4 RETAINING TABS 7716020X LIGHT 7523030E 30. Attach template A with masking tape to the roof console at the indicated position. 28. Enlarge the hole on the roof console with 9 mm drill bit. PUSHPIN CENTER OF THE FELT-TIP PEN MARK MASKING TAPE 2 MARKS TEMPLATE A 7517112E DRILL BIT (9 mm) 7524060E 31. Using a felt-tip pen, mark the center of the roof console as shown. 32. Use a pushpin to mark the roof console at two locations according to template A. 33. Remove template A. 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38137-38714 (0801) 7 of 12
34. Drill 4.5 mm holes at the two locations marked on the roof console in step 32. After drilling, remove any burrs. 39. Drill a 3 mm hole at the four locations marked on the roof console in step 36. DRILL BIT (4.5 mm) 19 mm HOLE SAW DRILL BIT (3 mm) 4 MARKS DRILL BIT (3 mm 6 mm 10 mm) 2 MARKS 7517120E 35. Attach template B with masking tape on the roof console at the indicated position. DRILL 7517141E PUSHPIN 4 MARKS FELT-TIP PEN TEMPLATE B 40. Enlarge the two 3 mm holes drilled in step 39 with a 6 mm drill bit and with a 10 mm drill bit as shown. 41. Enlarge the other two 3 mm holes drilled in step 39 with a 19 mm hole saw as shown. MASKING TAPE CENTER OF THE PUSHPIN 7517131E 36. Use a pushpin to mark the roof console at four locations according to template B. 37. Use a felt-tip pen and mark the roof console along the template B. 38. Remove template B. 8 of 12 AII 38137-38714 (0801) 2008 American Honda Motor Co., Inc. - All Rights Reserved.
42. Using a utility knife, cut along the marking made on the roof console in step 37. After cutting, remove any burrs. Mark made in step 37. UTILITY KNIFE 45. Connect the harness 22-pin connector to the control unit. CENTER CONTROL UNIT Cut out. CONTROL UNIT HARNESS Cut out. 43. Remove the masking tape attached in step 29. 7517152E 44. Using isopropyl alcohol on a shop towel, clean the areas where the double-faced tape will attach. Remove the adhesive backing from double-faced tape and attach the double-faced tape at the indicated position on the control unit. 2 DOUBLE-FACED TAPES Remove the adhesive backing. HARNESS 22-PIN 7517171E 46. Using isopropyl alcohol on a shop towel, clean the areas where the double-faced tape will attach. Remove the adhesive backing from the doublefaced tape attached to the control unit and attach to the roof console at the indicated position. 47. Use the holes drilled in step 34 and secure the bracket with two 4 x 12 mm washer screws to the roof console. Holes drilled in step 34. CONTROL UNIT 10 mm 10 mm 2 WASHER SCREWS, 4 x 12 mm CONTROL UNIT 7517161E BRACKET 7517180E 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38137-38714 (0801) 9 of 12
48. Bend the switch terminal as shown. 51. Connect the harness 20-pin connector to the switch. BACKSIDE OF THE SWITCH SWITCH SELF- TAPPING TERMINAL SCREW (Reuse.) (Bend.) SPEAKER SWITCH SWITCH TERMINAL TRIM SWITCH BUSHES (Reuse.) RETAINER HARNESS 20 -PIN BUSHES SELF- TAPPING SCREW 7517192E 52. Install the switch assembled in step 50 to the roof console with self-tapping screw, bushes, tapping screw removed in step 25 and vehicle bushes. 53. Reinstall the console light to the roof console. 4 SELF-TAPPING SCREWS, 3 x 10 mm 54. Using isopropyl alcohol on a shop towel, clean the area where the EPT sealer will attach. Cut an EPT sealer in half and attach one half to the vehicle bracket as shown. RETAINER RUBBER BUMPER 791209AB OPENING 49. Insert the rubber bumper to the retainer. 50. Assemble retainer, switch, and trim with four 3 x 10 mm self-tapping screws. BRACKET EPT SEALER (Cut in half.) EPT SEALER 7518010E 10 of 12 AII 38137-38714 (0801) 2008 American Honda Motor Co., Inc. - All Rights Reserved.
55. Hold the roof console close to the roof console opening and connect the harness 4-pin connector to the subharness 4-pin connector. 58. Connect the vehicle connectors to the roof console. Reinstall the roof console with the four bolts from step 5. GREEN WIRE TIE S BRACKET 4-PIN Vehicle front OPENING HARNESS 4-PIN 2 BOLTS 2 BOLTS 7518042E 7518020E 59. Install the fuse (2 A) into the fuse box at the indicated position. 56. Secure the connector with a wire tie to the vehicle bracket. 57. Using isopropyl alcohol on a shop towel, clean the area where the EPT sealer will attach. Secure the subharness to the vehicle roof panel inside the roof lining with three EPT sealers. 3 EPT SEALERS PANEL FUSE BOX FUSE (2 A) 2219080T 7518030E 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 38137-38714 (0801) 11 of 12
60. Attach the fuse label to the No. 33 slot on the fuse box cover. FUSE BOX COVER FUSE LABEL (OPITION FUSE 2 A) 61. Check that all wire harnesses are routed properly and that all connectors are plugged in. 62. Reinstall all removed parts. 63. Reconnect the negative cable to the battery. 64. Enter the customer s radio anti-theft code, and reset the radio station presets. 65. Reset the clock. NOTE: When the battery is disconnected, the driver s window AUTO function is disabled. Start the engine. Push down on the driver s window switch until the window is fully open. Pull up on the driver s window switch to close the window completely, then hold the switch for 1 second or more. No. 33 Lower and raise the driver s window to check operation of the driver s window AUTO function. 2219090T 12 of 12 AII 38137-38714 (0801) 2008 American Honda Motor Co., Inc. - All Rights Reserved.