Sales Administration Use Only Quote Name Quote Revision Shop Order Number Serial Number(s) Date Customer : Customer Name Salesperson Model : Salesperson Name Part / Drawing Number : 725-1021 : ST 9300 DT S4, Standard Duty Petroleum Trailer Customer Furnished Tractor Data Required Weights to Include Driver, Fuel, Tools, Equipment, etc. Enable Track Changes on the Review Tab to identify deviation from the Base Model Specification A. VESSEL A1. Shell Material Aluminum - 5454 alloy. All sizes/gauges are nominal. Top: 0.182in front section, 0.194in center section, 0.182in rear section Sides: 0.182in Bottom: 0.204in A2. Shell and Head Finish Enhanced mill finish bulk trailer sheet. A3. Shape Elliptical, Double Taper (DT) 50/50 Split with 6in pitch A4. Specification DOT 406 A5. Vapor Testing Tested at 5 PSI rated at 3.3 PSI. Vapor tested and certified to EPA Method 27-CA Air Resources Board standards and manholes sealed. A6. Nominal Capacity 9,300 Gallons plus 3% outage. 60 gallons is the minimum outage for any size compartment. A7. Compartments 4 Compartments, front to rear - 3500/2000/1100/2700 A8. Bulk Heads Aluminum - 5454 alloy. All sizes/gauges are nominal. Configuration: Front: Rear: Compartments: All single heads between compartments. 0.204in stiffened and shoed 0.204in stiffened and shoed 0.204in unstiffened A9. Surge Heads Aluminum - 5454 alloy. All sizes/gauges are nominal. All surge heads are dished & flanged with (1) 20" man way center, (2) 12" drain holes 6 and 12 o'clock, and (2) 3" emergency drain holes @ 3 and 9 o'clock. Over Kingpin: 0.204in stiffened and shoed Over Rungear: 0.186in stiffened and shoed Middle of Tank: 0.186in unstiffened A10. Flashing Full length, double leg extrusions. Dams front and rear with transverse overturn protection rails as required by code. Page 1 of 6
A11. Documentation Computer generated calibration charts 1/2" increments. HM-183 documentation w/markings on front head. Vapor test decal with documentation. Unit hydrostatically tested. A12. Operating -20 F to 180 F Temperature A13. Lading Gasoline, Diesel Fuel, or similar A14. Miscellaneous B. TANK FITTINGS AND PIPING B1. Manholes (1) 16" Civacon offset manhole per compartment. Includes NV3000 PV Valve,10 aluminum vent, and Buna N gaskets. Meets HM 183 and CFR49 178.364-10 venting requirements. B2. Capacity Indicators Indicator Rods: Additional Discs: If ordered, each capacity indicator rod will come with one disc. Additional discs may be ordered. B3. Internal Ground (1) 1/8" stainless steel static ground wire per compartment. B4. Venting DOT406 venting in manhole. B5. Cleanouts/ Fill Covers B6. Vapor Recovery Vent Materials: B7. Vapor Recovery Connection B8. Vapor Recovery Piping (1) 3" Civacon air operated inward opening sequential vent per compartment. Located in each manhole cover. Aluminum vent with stainless trim & Viton seats. Black Nylon vapor recovery nipple connected to flashing rail A hose connects the vapor recovery vent to the vapor recovery nipple 4" Aluminum Internal vapor line from flashing rail through mid-tank. Line to continue to the following locations: (1) curbside outlet 15" to rear of last discharge valve. (4" outlet). (1) curbside outlet to rear of rear head. (4" outlet). B9. Vapor Recovery Fittings (1) 4in adapter and dust cap, curbside, 15" to rear (1) 4in adapter and dust cap, curbside, rear of rear head All vapor adapters are eight (8) bolt TTMA flange mounted and located per API RP 1004, where applicable. Page 2 of 6
B10. Additional Venting B11. Emergency Valve (1) Civacon 5 x 4 MaxAir II TM, internal cylinder, EV per compartment Materials: Aluminum body with Teflon seat. Splash shield-vortex breaker over each EV. B12. Operator System Civacontrol II air control kit. To simplify piping, a straight valve may be used in place of an elbow style. Mounted in EVO cabinet One emergency trip located street side, front of tank. B13. Piping/Piping Gasket Flanged: Grooved: Grooved: 4" Schedule #10 aluminum discharge piping with large radius formed sweeps to curbside of tank, located per API standards. Viton gaskets on flanged piping connections Dixon Aluminum couplers on groove-groove connections Baylast gaskets on groove-groove connections B14. Discharge Valve (1) 4" Civacon openable adapter per compartment B15. Discharge Accessories Materials: Aluminum handle and Viton seals (2) 4" API to 4" cam style hose adapters and caps (2) API dust caps. B16. Streetside Discharge B17. Pump Off-Line B18. Overfill System Civacon ROM II system with enhanced controller which includes an electro-pneumatic switch for sequential venting. Monitor Probe: Socket: Socket Mounted on trailer frame. (1) top probe per compartment Installed in manhole cover (1) Optic socket (Ref. SJ6W-WOGA). On bracket adjacent to monitor, not in enclosure. Ground proving device is included with the socket. Socket: Socket (1) Thermistor socket (Ref. SJ6S). On bracket adjacent to monitor, not in enclosure. Ground proving device is included with the socket B19. Brake Interlock Safety interference bar with lock down pin handle over discharge valves and vapor outlet(s). Activates (1) brake interlock valve. Page 3 of 6
B20. Overfill Interlock B21. Miscellaneous C. ACCESSORIES Rear vapor outlet to have separate interlock valve C1. Ladder Rear aluminum ladder, center of head, with serrated rungs and platform top step. Step below bumper C2. Walkway Adhesive backed, skid-resistant tape between flashing rails. Walkway drains through rear ladder C3. Hose Carriers (1) Double hose tube kit. Size: Material: Door: 7in x 21ft Aluminum, reinforced for extended wear Curbside rear Single door at front C4. Stick Tube C5. Cabinets (1) 16"W x 24"H x 20"D aluminum, EVO cabinet, single door, stainless steel hinge Mounted curbside in front of piping. C6. Splash Guard Front and rear, HEIL, anti-sail, anti-spray flaps. C7. Fenders (2) Single contour front fenders. (2) Double contour rear fenders. C8. Placards\Doc. Holders C9. Lights 12 Volt Truck Lite flange mount LED lamp system complying to FMVSS with conspicuity markings each side and rear. Combination mid-tank clearance and turn signals, one each side One oval third stop light, located rear center of trailer. (2) Aluminum light boxes at rear, one each side of tank. C10. Wiring (1) 7 way ATA (#SAE J560) connector in nose box Located at lower streetside front head C11. Miscellaneous D. CHASSIS 12 Volt system, 7 wire, molded conduit throughout All connections made in junction boxes Page 4 of 6
D1. Upper Fifth Hi-tensile steel, bolted and adjustable with 2" forged kingpin. Wheel D2. Skid Plate Aluminum skid plate. D3. Landing Legs Jost model A-HEIL magnum 2-speed, sealed gear box with arctic grade grease, 70,000 lbs. rated lift capacity with 10 x 12 sand shoes and street side crank. D4. Landing Legs Finish Powder coat gray finish for improved durability. D5. Suspension Heil s R2R value package includes Hendrickson AANT 23K air ride suspension & brake system, 71.5" track 5.75 diameter axle, parallel spindle, 23,000 lb. beam rating, 49" spacing, with single leveling valve. D6. Suspension Finish D7. Suspension Frame Bumper: (RIG) Underride: D8. Suspension Frame Finishing Suspension Towers painted DuPont Imron Gray Integrated axle painted DuPont Imron Gray Aluminum suspension sub frame. Suspension bolted to sub frame with electrolysis barrier. Aluminum DOT compliance bumper per FMVSS223 Underride is typically not required per wheels back exemption; however, it will be added if required by suspension location. Natural aluminum surface finish. D9. Brake System Aluminum tank air system meeting FMVSS 121 requirements ECU: Configuration: Glad Hands: Constant Power: WABCO RSS 4S/2M ABS with Roll Stability 16.5" x 7" (quick change) S-cam type drum brake system Philips "Quick Release" glad hand on service line. Auxiliary, blue circuit, center pin of SAE J560 7-way. D10. Brake Chamber OEM type 30-30 parking-emergency spring brake D11. Brake Lining OEM brake lining D12. Slack Adjuster OEM slack adjuster D13. Drums (4) Centrifuse - outboard mount brake drums (16.5" x 7"). D14. Axles (2) Integral with air ride D15. Paint Unless otherwise specified, steel parts will be painted DuPont Imron 5000 series gray. D16. Accessories Page 5 of 6
D17. Miscellaneous E. Wheel End E1. Warranty Heil s R2R 5C warranty package which includes ConMet s five-year wheel end warranty E2. Hubs (4) ConMet aluminum preset 10 Stud, hub pilot (single nut mount) hub for outboard drum E3. Oil Seals Preset bearings with premium oil seals for Heil's R2R package F. WHEELS F1. Wheels 0 G. TIRES G1 Tires 0 H. MISCELLANEOUS H1. Customer Supplied Parts H2. Warranty Heil s standard four year warranty - one year bumper to bumper coverage with some areas (e.g., barrel and frame) being extended on a pro-rated basis out as much as 4 years. Heil s value package includes Jost s 5 year maintenance free landing gear warranty. Heil s value package includes Civacon s 3 year System3 component warranty. Heil s value package includes Dupont s prorated 3 year warranty on painted steel parts and prorated 4 year warranty on painted aluminum parts. H3. Notes Operational manual and information CD is included and shipped with each trailer. H4. Other Page 6 of 6