NELES R-SERIES SEGMENT VALVE Flanged RE and Wafer RE1

NELES R-SERIES SEGMENT VALVE Flanged RE and Wafer RE1 Metso's Neles RE series control valves are economical, high performance valves in a quarterturn design. They are offered with a variety of trim options from standard and low Cv trims for general applications to noise/cavitation Q-Trim for reducing aerodynamic noise and preventing cavitation. Standard units are equipped with either diaphragm or cylinder actuators and ND9 intelligent valve controllers for precise control, reliability and performance monitoring on-line. FEATURES Integral body construction Integrally flanged R-Series valves feature one piece body construction with no flange rings, inserts or end caps to create potential leak paths, even if the valve is subjected to pipe bending forces. Seating capabilities are totally unaffected by pipeline forces, which assures reliable valve operation. Accurate Control Carefully designed V-ported segmented ball, low torque requirements and backlash-free movement results in exceptional control performance. This design provides steady and gental contact between the seat and segment at all times to minimize friction while at the same time providing exceptional control characteristics. Bearings are located inside the valve body providing larger bearing areas, lower bearing loads and longer bearing life. Economical Low torque operation reduces wear, resulting in better reliability. In addition, standard designs carry hard chromium facing on the segment and a stellited seat, which has been designed to avoid flow impingement. Together with a low load bearing design and liveloaded packing, operational life is improved and maintenance needs are minimized. Low torque combined with a well integrated actuator design provides a lower cost valve assembly. Safety and Environmental Rotary operation reduces fugitive emissions dramatically compared to sliding stem designs. The R-series stem seal design meets the US clean Air Act and German TA-Luft requirements. Durable metal seat The seat of the R-series V-port segment valve is firm and uniquely durable. The seat is designed in such a way that its sealing surface is not located directly in the flow stream. This gives the seat an extended service life. The working principle is a pressure-aided seat which enables good sealing properties at a low pressure difference. The seat is located inside the valve, which prevents forces from the pipe system influencing the sealing effect. Two-way tight seat is available as an option. Low flow and noise attenuation/cavitation Q-Trim options 1" valves feature five different segment sizes. They extend the valves application range to very low-flow and high accuracy services, such as additive and coloring lines, pilot plants etc. Cavitation and aerodynamic noise are reduced with the patented Q-Trim option. This self-cleaning design handles contaminated flows (impure steam, river water, etc.) without plugging. Reliable actuators Quadra-Powr spring diaphragm operators provide safe, reliable operation even with minimal supply pressures are available. B-Series piston actuators are available in either double acting or spring return versions. 3 R 25 US 12/1

METSO 3 R 25 US EXPLODED VIEW A SEAT 4 4 7 5 8 5 4 2 19 17 18 17 35 35 RE15-8 RE25- E SEAT T SEAT 12 1S SEAT 14 3 15 4B 5 4A 4 22 4 5 S SEAT (standard construction) 1 11 13 1 1 9 24 32 25 DETAIL A 1) Alternative materials * The parts are not in number order since certain parts have dedicated part numbers. PARTS LIST (standard construction)* Part Name BODY MATERIAL Stainless steel Carbon steel 1 Body ASTM A351 gr. CF8M ASTM A21 gr. WCB 3 V-port segment AISI 329 + chromium / CG8M + chromium 1) AISI 329 + chromium / CG8M + chromium 1) 4 Seat AISI 31 + Cobalt based alloy / PTFE 1) AISI 31 + Cobalt based alloy / PTFE 1) 4A Back ring AISI 31 AISI 31 4B Support ring AISI 31 AISI 31 5 Lock spring INCONEL 25 INCONEL 25 Back seal Stainless steel + PTFE / Viton GF / Graphite Stainless steel + PTFE / Viton GF / Graphite 7 Retaining ring EN 28-1.4571 EN 28-1.4571 8 Support ring AISI 31 AISI 31 9 Gland follower ASTM A351 gr. CF8M ASTM A351 gr. CF8M Blind flange ASTM A351 gr. CF8M ASTM A351 gr. CF8M 11 Drive shaft AISI 329 / 17-4PH 1) AISI 329 / 17-4PH 1) 12 Shaft AISI 329 / 17-4PH 1) AISI 329 / 17-4PH 1) 13 Key AISI 329 AISI 329 14 Cylindrical pin AISI 329 / 17-4PH 1) AISI 329 / 17-4PH 1) 15 Cylindrical pin AISI 329 / 17-4PH 1) AISI 329 / 17-4PH 1) 1 Bearing PTFE + SS net / cobalt based alloy 1) PTFE + SS net / cobalt based alloy 1) 17 Bearing PTFE + SS net / cobalt based alloy 1) PTFE + SS net / cobalt based alloy 1) 18 Thrust bearing Cobalt based alloy 1) Cobalt based alloy 1) 19 Sealing plate Graphite / PTFE Graphite / PTFE Packing Graphite / PTFE Graphite / PTFE 22 Filling ring (only low Cv 1"/DN 25) Stainless Steel AISI 31 Stainless Steel AISI 31 24 Stud ISO 35 A4-8/B8M ISO 35 A4-8/B8M 25 Hexagon nut ISO 35 A4-8/B8M ISO 35 A4-8/B8M 2 Hexagon bolt ISO 35 A4-8/B8M ISO 35 A4-8/B8M Retainer plate AISI 31 AISI 31 32 Spring stack SIS 2324 & CrMo Steel + ENP SIS 2324 & CrMo Steel + ENP 35 Identification plate AISI 31 AISI 31 2 TECHNICAL BULLETIN 12/1

3 R 25 US NELES R-SERIES SEGMENT VALVE Flanged RE and Wafer RE1 Type Integrally flanged V-ported ball, quarter-turn valve Pressure ratings are as follows: Body: ASME 15 -, see page 5. Trim: See tables on page 5. Sizes RE1; 1", 1 1/2", 2", 3", 4", ", 8" RE; 1", 1 1/2", 2", 3", 4", ", 8", ", 12", 14", 1", ", 24", 28", 32" Wafer (RE1) Flanged (RE, RE13) End Connections TECHNICAL SPECIFICATIONS Shut-off classification ANSI/FCI 7.2 Class IV - Standard with metal seats. Tested with 5 psig water. ANSI/FCI 7.2 Class V - Standard with soft seats. Tested with psig water. 1/th ANSI/FCI 7.2 Class IV (Not Available with Low Cv Trims) - Optional with metal seats. Tested with 5 psig air. E-Seat is non-tight See table on this page. Flow capacity Face-to-face dimensions ASME/ISA S75.4, IEC 534-3-2. IEC 534-3-2. Optional B1. with spool piece construction. Temperature range -5 C... + C / -58 +5 F with soft bearings -5 C... +315 C / -58 + F with metal bearings in sizes 2" - " -5 C... +425 C / -58 +8 F with metal bearing and high temperature seats in sizes 2" - ". Inherent flow characteristic Standard V-port: Equal percentage. Q-Trim: Modified equal percentage. Fire safety Fire safe design to meet API 7, 3rd edition. Clockwise to close. Valve trim rotation OPTIONS Q-trim: Inch 2", 3", 4", ",8", ", 12", 14", 1", ", 24", 28", and 32" Reduced Cv trim: For 1" valve only. Valve body and seat test All valves manufactured by Metso undergo pressure testing. The test pressure of R-series valve body is 1.5 x the pressure rating and the standard test pressure of seat is 1.1 x the maximum permissible shut-off pressure or lower depending on size and material. The test medium is water containing a corrosion inhibitor. Seat design options shown on the next page. 1) % corresponds to 95 turning angle 2) For Q-R-valves, % corresponds to 9 turning angle Maximum C V Coefficients for R-Series Valves Size Metal Seat, S Q-Trim S Seat Metal Seat, 1S Q-Trim 1S Seat Soft Seat, T Q-Trim, T Seat Metal Seat, A Q-Trim, A Seat INCH DN C V % 1) C V % 2) C V % C V % C V % C V % C V % C V % 1 25 45-24 - 21 - - 1.5 1-58 - 1 - - 2 5 18 47 115 1 29 1 39 2.5 5 28 9 2 72 215 74 - - 3 8 4 342 1 3 1 35 15 4 25 5 2 5 2 5 2 15 1 5 1 5 7 459 1 5 8 88 19 8 17 73 18 835 25 32 15 5 14 28 1331 14 12 449 21 43 7 8 1945 - - 14 35 4 3 2 5 575 2821 - - 1 85 418 83 9 7 3748 - - 5 1 125 37 117 591 - - 24 - - 197 92 - - - - 28 7 - - 25 137 - - - - 32 8 - - 1181 - - - - TECHNICAL BULLETIN 12/1 3

METSO 3 R 25 US S Metal seat T Soft seat SEAT DESIGNS S Metal seat Seat: 31 SS + Cobalt based hard facing, sizes 1" - 32" / DN 25-8 Spring: Inconel 25 Seat seal: Filled PTFE lipseal / SS Elgiloy spring Temp. Range: -5 C... +315 C / -58 F + F Service: General Flow direction E Non-tight metal seat Flow direction 1S 2-way tight metal seat T Soft seat Seat: 31 SS with PTFE + X-treme, sizes 1" - " 31 SS with PTFE + C25 % insert, sizes 8" - 32" Spring: Inconel 25 Seat seal: Filled PTFE lipseal Back seal: PTFE Temp. Range: -5 C... + C / -58 F +5 F Service: General service with tight shut-off. E Non-tight metal seat Seat: Cobalt based alloy Temp. Range: 5 C... +425 C / -58 F +8 F Service: Extremely erosive applications, non-tight. NOTE! Flow direction is reversed. Flow direction A High temp. metal seat Flow direction 1S 2-way tight metal seat Seat: 31 SS + Cobalt based hard facing, sizes 1" - 32" / DN 25-8 Spring: Inconel 25 Seat seal: Viton GF Temp. range: - C... + C / -22 F +392 F Service: General Flow direction A High temp. metal seat Seat: A: SS 31 + Cobalt based hard facing A1: SS 31 + CrC facing (with K segment) Spring: Inconel 25 Seat seal: Graphite Temp. range: -5 C... +425 C, -58 F... +8 F Service: General service Size: NPS 2" - " / DN 5-25: Note: Available with model code A only (11. sign) CONSTRUCTION OPTIONS Low C v trims Reduced C v trims are available on the 1" valve to control very low flows with high accuracy. The narrow orifice is a selfflushing design because the trim orifice is continually increasing. Q-trim valve trim for cavitation/noise abatement Liquid cavitation and aerodynamic noise problems can be solved with the patented Q-Trim valve trim. This design employs the two well-known principles of dividing the pressure drop into a series of small pressure drops and of separating the flow stream into many small jet streams. The use of these two principles combined with the rotation of the attenuator elements provides a combination of cavitation/noise abatement with high rangeability, high capacity and the capability to handle impure fluids. Erosion resistant version This heavy duty erosion resistant design handles contaminated flows and abrasive media at a favorable cost/useable life ratio. The seat is machined from cobalt chromium alloy and the seat design is changed from normal to reverse flow for maximum abrasion resistance. This version should not be used for isolation service since the seat is not in contact with the segment. 4 TECHNICAL BULLETIN 12/1

3 R 25 US NELES R-SERIES SEGMENT VALVE Flanged RE and Wafer RE1 BODY PRESSURE RATINGS Pressure bar 5 ASME PN PN25 ASME 15 PN1 PN CF8M 122 212 2 392 482 572 2 752 842 87 5 15 25 35 45 725 Pressure bar WCB 122 212 2 392 482 572 2 752 842 87 ASME 5 725 PN PN25 ASME 15 PN1 PN 5 15 25 35 45 Maximum operating pressure differential in shut-off service 5 DN25-8/1"-3" AISI 329 Shaft 122 212 2 392 482 572 2 87 725 Pressure Bar DN-15/4"-" DN-25/8"-" DN-7/12"-28" 5 15 25 35 17-4PH Shaft 122 212 2 392 482 572 2 752 842 87 Pressure Bar 5 DN25-8/1"-3" DN-15/4"-" DN-25/8"-" DN-7/12"-28" 725 5 15 25 35 45 TECHNICAL BULLETIN 12/1 5

METSO 3 R 25 US Max operating pressure differential in control service, RE opening range %-7 % 122 212 2 392 482 572 2 752 842 87 Pressure Bar 5 DN25-8/1"-3" DN-15/4"-" DN-25/8"-" DN-7/12"-28" 725 5 15 25 35 45 35 DN25-8/1" - 3" Max operating pressure differential in control service, RE opening range 7 %- % 122 212 2 392 482 572 2 752 842 25 DN - /4" - 8" Pressure Bar 15 DN25/" DN-7/12" - 28" 5 5 15 25 35 45 TECHNICAL BULLETIN 12/1

3 R 25 US NELES R-SERIES SEGMENT VALVE Flanged RE and Wafer RE1 Max operating pressure differential in control service, Q-RE opening range %- % 122 212 2 392 482 572 2 752 842 87 Pressure Bar 5 DN5-8/2"-3" DN-15/4"-" DN-25/8"-" DN-/12"-24" DN7/28" 725 5 15 25 35 45 Max operating pressure differential in control service, Q-RE opening range % - % 122 212 2 392 482 572 2 752 842 87 Pressure Bar 5 DN5&8/2"&3" DN5/2,5" DN/4" DN15/" DN/8" DN25/" DN-/12"-24" DN7/28" 725 5 15 25 35 45 35 DN5-8/2"-3" Max operating pressure differential in control service, Q-RE opening range %- % 122 212 2 392 482 572 2 752 842 Pressure Bar 25 15 DN/4" DN15/" 5 DN25/" DN-/12"-24 DN7/28" 5 15 25 35 45 Note: 1) RE-valves are not recommended for applications with high on-off cycling rate. X- or L-series valves should be used in these cases. 2) Please observe body rating for material in question when determining maximum allowable shut-off pressure differential. Given maximum allowable throttling differential pressures are based on mechanical strength of the parts only. Nelprof analysis determines actual throttling dp capability, taking into account trim velocity, exit velocity, noise and cavitation. TECHNICAL BULLETIN 12/1 7

METSO 3 R 25 US SELECTION OF STANDARD ACTUATORS, QUADRA POWR VALVE SIZE inch ACTUATOR SIZE SPRING RATE psi MAX SHUT-OFF DP psi RE, Q-RE MAX CONTROL DP psi RE MAX CONTROL DP psi Q-RE ND Intelligent Valve Controller Recommmended model NP Pneumatic Positioner Recommmended model 1 QP1C 727 59 57 ND 93 NP 729 1 1/2 QP1C 727 59 57 ND 93 NP 729 2 QP1C 727 59 57 ND 93 NP 729 3 QP1C 3 3 319 ND 93 NP 729 3 QP2B 41 59 59 57 ND 93 NP 729 3 QP2C 727 59 57 ND 93 NP 729 3 QP2D 8 727 59 57 ND 93 NP 729 4 QP2C 59 34 21 ND 93 NP 729 4 QP2D 8 582 34 21 ND 93 NP 729 4 QP3B 41 582 34 21 ND 93 NP 724 4 QP3C 582 34 21 ND 93 NP 724 QP3B 41 3 3 21 ND 93 NP 724 QP3C 7 34 21 ND 93 NP 724 QP3D 8 582 34 21 ND 93 NP 724 QP4B 41 582 34 21 ND 9 NP 724 QP4C 582 34 21 ND 9 NP 724 8 QP3C 233 233 217 ND 93 NP 724 8 QP4B 41 7 34 217 ND 9 NP 724 8 QP4C 59 34 217 ND 9 NP 724 8 QP4D 8 59 34 217 ND 9 NP 724 QP4C 291 291 ND 9 NP 724 QP4D 8 7 291 ND 9 NP 724 QP5B 41 45 291 ND 9 NP 72 QP5C 59 291 ND 9 NP 72 12 QP5B 41 218 11 ND 9 NP 72 12 QP5C 34 11 ND 9 NP 72 12 QP5D 8 43 11 ND 9 NP 72 14 QP5C 174 11 ND 9 NP 72 14 QP5D 8 247 11 ND 9 NP 72 1 QP5C 11 11 11 ND 9 NP 72 1 QP5D 8 189 11 ND 9 NP 72 NOTES 1) Maximum shut-off differential pressures for valves are given considering clean media. Safety margins between % - 25 % are typically recommended for cases where media is sticky or has tendency to built-up inside the valve. 2) Selection is based on supply pressures as per relevant spring rate. 3) Maximum shut-off differential pressures are given at ambient temperature, see curves on page 5. 4) Maximum control differential pressures must not be based on values in this table only. Nelprof calculation, taking into account noise level, inlet/outlet velocity, existence of cavitation, and actuator load factors must be observed when determing valves' differential pressure capability. 8 TECHNICAL BULLETIN 12/1

3 R 25 US NELES R-SERIES SEGMENT VALVE Flanged RE and Wafer RE1 DIMENSIONS RE1-Series RE1-Series INCH DN RE1-Series Dimensions (inch) Shaft Dimensions (inch) (RE_A Keyed Shaft) Flange Dimensions & Weights A1 A C ød K S T U L H E R øo M P N øb Ibs 1 25 2.1 4.2 2.2 1.3 7.17 2.7 - M.1 3.15 8.15 4.13.59.19.7.98 2.52 9 1.5 2.24 4.49 2.5 1.93 7.42 2.7 - M.1 3.15 8.41 4.13.59.19.7.98 3.23 11 2 5 2.44 4.88 3.58 2.3 7.85 2.7 - M.1 3.15 8.84 4.13.59.19.7.98 3.94 18 3 8 3.25.5 4.25 3.5 9.13 3.54 - M12.3 3.54.51 4.92.79.19.87 1.38 5.12 31 4 3.82 7.4 4.72 4.45 9.49 3.54 - M12.3 3.54.87 4.92.79.19.87 1.38.22 15 4.51 9.2.85.4 11.42 4.33 1.2 M12.87 3.54 13.19 5.31.98.25 1.9 1.81 8.5 84 8 4.39 9.57 7.91 8.7 13.58 5.12 1.2 M12.87 4.33 15.55.3 1.18.25 1.3 2.1.55 143 INCH DN Dimensions (mm) Shaft Dimensions (mm) (RE_A Keyed Shaft) Flange Dimensions & Weights A1 A C ød K S T U L H E R øo M P N øb kg 1 25 51 2 5 33 182 7 - M 15.5 8 7 5 15 4.7 17 25 4 4 1.5 57 114 5 49 188.5 7 - M 15.5 8 213.5 5 15 4.7 17 25 82 5 2 5 2 124 91 199.5 7 - M 15.5 8 224.5 5 15 4.7 17 25 8 3 8 82.5 15 8 89 232 9 - M12 1 9 27 125 4.7 22.2 35 1 14 4 97 194 1 113 241 9 - M12 1 9 27 125 4.7 22.2 35 158 18 15 114.5 229 174 14 1 32 M12 22 9 335 135 25.35 27.8 4 21 38 8 111.5 243 1 5 345 1 32 M12 22 1 395.35 32.9 51 28 5 TECHNICAL BULLETIN 12/1 9

METSO 3 R 25 US Series RE M 1"-4" S M "-" S U 24"-32" S S2 RE_A 1"-32" (KEY) P øo C DN ød øb K (L) E H R N M T T A A1 Valve is shown in closed position Series RE INCH DN Dimensions (inch) Shaft Dimensions (inch) (RE_A Keyed Shaft) Flange Dimensions & Weights ASME 15 ASME A1 A C ød K S/S2 T U L H E R øo M P N øb lbs øb lbs 1 25 2.1 4.2 2.2 1.29/1.49 1) 7.17 2.7 - M.1 3.15 8.15 4.13.59.19.7.98 4.25 8 4.88 11 1.5 2.24 4.49 2.5 1.93 7.42 2.7 - M.1 3.15 8.41 4.13.59.19.7.98 5 11.1 17 2 5 2.44 4.88 3.58 2.3 7.85 2.7 - M.1 3.15 8.84 4.13.59.19.7.98 5.98 17.5 21 2.5 5 2.85 5.71 3.82 2.95 8.7 2.7 - M.1 3.15 9.9 4.13.59.19.7.98 7.28 29 7.28 29 3 8 3.25.5 4.25 3.5 9.13 3.54 - M12.3 3.54.51 4.92.79.19.87 1.38 7.52 31 8.27 42 4 3.82 7.4 4.72 4.45 9.49 3.54 - M12.3 3.54.87 4.92.79.19.87 1.38 9.2 47 4 15 4.51 9.2.85.4 11.42 4.33 1.2 M12.87 3.54 13.19 5.31.98.25 1.9 1.81.98 8 12.52 119 8 4.39 9.57 7.91 8.7 13.58 5.12 1.2 M12.87 4.33 15.55.3 1.18.25 1.3 2.1 13.5 137 15 183 25 5.45 11.9 9.88.2 15.24 5.12 1.2 M12 1.2 4.33 17.52.1 1.38.38 1.54 2.28 15.98 1 17.72 12. 13.31.59 11.81 17.52.3 1.57 M1 1.2 4.72 19.9 7.4 1.57.38 1.74 2.8 19.2 313.47 438 14 35.89 15.75 12.24 13.78 19.13.3 1.57 M1 1.14 4.72.2 7.87 1.77.5 1.98 3.15 21.2 447 22.99 25 1.3 15.75 13.9 15.75 21.77.3 2.17 M 1.14 5.51 22.99 9. 1.97.5 2.19 3.54 23.5 581 25.51 781 5 9.17 1.54 19.9 24.33 9. 3.54 M27 1.57 7.9 28.2 11.5 2.7.75 3.8 4.9 27.52 12.51 13 24 13.98 24.2 19.29 23.2 27.72 13/12 4.72 M 1.57 8. 32.99 13.94 2.95.75 3.22 5.28 32.9 2128 3.2 253 28 7 11.1 27.95 21.22 27.5.24 13/12 4.72 M 2.17 8. 35.98 14.41 3.35.88 3.75 5.75 3.42 2748.75 3327 32 8 14.9 33.7 25 31.5 34.31 13/12 4.72 M 2.17 8. 41.42 15.83 4.13 1 4.51 7.9 41.73 7 45.28-1) 1.49" (38 mm) for low capacity segment (eg C5-RE) Series RE INCH DN Dimensions (mm) Shaft Dimensions (mm) (RE_A Keyed Shaft) Flange Dimensions & Weights ASME 15 ASME A1 A C ød K S/S2 T U L H E R øo M P N øb kg øb kg 1 25 51 2 5 33/38 1) 182 7 - M 15.5 8 7 5 15 4.7 17 25 8 3. 124 4.9 1.5 57 114 5 49 188.5 7 - M 15.5 8 213.5 5 15 4.7 17 25 127 4. 155 7.5 2 5 2 124 91 199.5 7 - M 15.5 8 224.5 5 15 4.7 17 25 152 7.4 15 9.5 2.5 5 72.5 97 75 5 7 - M 15.5 8 231 5 15 4.7 17 25 185 13 185 13 3 8 82.5 15 8 89 232 9 - M12 1 9 27 125 4.7 22.2 35 191 14 2 19 4 97 194 1 113 241 9 - M12 1 9 27 125 4.7 22.2 35 229 21 254 29 15 114.5 229 174 14 1 32 M12 22 9 335 135 25.35 27.8 4 279 39 318 54 8 111.5 243 1 5 345 1 32 M12 22 1 395.35 32.9 51 343 2 381 83 25 138.5 297 251 259 387 1 32 M12 2 1 445 18 35 9.53 39.1 58 91 45 139 12 154 338 29 445 M1 2 1 485 188 9.53 44.2 8 483 142 5 199 14 35 175 311 35 48 M1 29 1 513 45 12.7 5.4 8 534 3 584 284 1 353 553 55 M 29 1 584 2 5 12.7 55.5 9 597 24 48 355 5 233 58 4 5 18 2 9 M27 18 727 292 7 19.5 78.2 119 99 55 775 24 355 49 74 3/4.7 1 M 2 838 354 75 19.5 81.9 134 815 97 915 115 28 7 295 7 539 7 78 3/4.7 1 M 55 2 914 3 85 22.23 95.3 14 925 1249 35 1512 32 8 38 8 35 8 871.5 3/4.7 1 M 55 2 52 2 5 25.4 114.5 18 185 115-1) 1.49" (38 mm) for low capacity segment (eg C5-RE) TECHNICAL BULLETIN 12/1

3 R 25 US NELES R-SERIES SEGMENT VALVE Flanged RE and Wafer RE1 RE/RE1-QPX RE/RE1-QPX INCH DN QPX Size Dimensions (inch) Weight Weight Weight A E F G H I J K X Pipe d 15# (lbs) # (lbs) RE1 (lbs) 1 25 1 4.2 5. 15.4 13 15.28.3 8.8 7.17 8.39 9. 42 4 33 1.5 1 4.49 5. 15.4 13 15.91.3 9.14 7.45 8.39 9.5 44 51 38 2 5 1 4.89 5. 15.4 13 17.37.3 9.57 7.88 8.39.44 49 55 42 3 8 2.5 5. 15.4 13 19.93.78 11.19 9.14 8.39 13 84 95 73 4 2 7.4.15 18.9 15.32.75.78 11.54 9.49 8.98 13.78 99 117 82 15 2 9.2.15 18.9 15.32 24.81 7.52 13.47 11.42 8.98 17.72 139 172 12 3 9.2 7.49 22.25 17.5 25.87 8.43 13.3 11.42.79 1.15 172 5 157 8 3 9.57 7.49 22.25 17.5 29.1 7.52 15.79 13.59 9.73.48 223 29 21 4 9.57 8.98 25 19.49.24 8.43 1.3 13.59 12. 19.1 27 313 25 4 11.7 8.98 25 19.49 33.8 8.43 17.8 15.24 12. 22.45 3 43-5 11.7.87.24 23.94 35.7 9.57 18.27 15.24 15.4 21.2 451 557-12 5 13.31.87.24 23.94 38.7 8.43.5 17.52 15.4 25. 54 89-14 35 5 15.75.87.24 23.94 41.93 9.57 22.17 19.14 15.4 28.94 98 87-1 5 15.75.87.24 23.94 4.23 9.57 24.81 21.78 15.4 34.2 832 34 - RE/RE1-QPX INCH DN QPX Size Dimensions (mm) Weight Weight Weight A E F G H I J K X Pipe d 15# (lbs) # (lbs) RE1 (lbs) 1 25 1 2 142 382 3 388 225 182 213 2 19.5 15 1.5 1 114 142 382 3 4 232 189 213 245 23 17 2 5 1 124 142 382 3 441 243 213 25 22 25 19 3 8 2 15 142 382 3 5 172 284 232 213 3 38 43 33 4 2 194 15 48 389 527 172 293 241 228 35 45 53 37 15 2 229 15 48 389 191 342 228 45 3 78 57 15 3 229 19 55 44 57 214 34 274 4 78 93 71 8 3 243 19 55 44 739 191 1 345 247 5 1 122 98 8 4 243 228 35 495 78 214 7 345 3 485 121 142 118 25 4 297 228 35 495 8 214 449 387 3 57 15 198-25 5 297 27 78 8 9 243 44 387 382 5 5 253-12 5 338 27 78 8 982 214 522 445 382 5 25 313-14 35 5 27 78 8 5 243 53 48 382 735 317 398-1 5 27 78 8 1174 243 553 382 87 378 47 - TECHNICAL BULLETIN 12/1 11

METSO 3 R 25 US RE-B1C NPT MOUNTING POSITION A (STANDARD) X NPT ød G F SUPPLY G 1/4 A A1 SIGNAL M X 1.5 V NPS øb (only RE) C J I H FLOW DIRECTION RE-B1C INCH DN B1C Dimensions (inch) REC_ASME 15 REC_ASME RE1 NPT Size A C ød F G X V J H Imax øb lbs øb lbs lbs 1 25 4.2 2.21 1.29/ 1.491) 15.75.24 3.55 1.42 9.45 13.43 12.21 1/4 8 27 124 27 18 1.5 4.49 2.5 1.93 15.75.24 3.55 1.42 9.73 14. 12.21 1/4 127 155 32 21 2 5 4.89 3.59 2.37 15.75.24 3.55 1.42.1 15.52 12.21 1/4 152 3 15 37 27 2.5 5 5.71 3.82 2.9 15.75.24 3.55 1.42.44 1.15 12.21 1/4 185 - - - 3 8.5 4.2 3.51 15.75.24 3.55 1.42 11.42 17.45 12.21 1/4 191 47 2 58 4 7.4 4.73 4.45 15.75.24 3.55 1.42 11.78 18.27 12.21 1/4 229 3 254 7 49 15.75.24 3.55 1.42 13.71 22.33 12.21 1/4 2 113 97 15 9 9.2.8.4 17.92 12.41 4.34 1.7 13.75 22.7 12.1 1/4 279 115 318 12 1 11 21.2 14.77 5.32 2.5 13.98 23.51 12.21 3/8 1 141 121 15.75.24 3.55 1.42 15.87 25.5 12.21 1/4 152 198 147 8 9 9.57 7.92 8.8 17.92 12.41 4.34 1.7 15.91 25.99 12.1 1/4 343 15 381 212 15 11 21.2 14.77 5.32 2.1 1.15 2.74 12.21 3/8 181 227 17 9 17.92 12.41 4.34 1.7 17.5 29.1 12.21 1/4 229 335-25 11 21.2 14.77 5.32 2.1 17.8.3 12.21 3/8 251 35-11.7 9.89.2 45 13 25 17.52.89 2.5 18.43 31.78 12.8 3/8 383-12 14 35 1 17.32 21.4 8.47 3.8 19.2 33.15 13.39 1/2 357 434-11 21.2 14.77 5.32 2.1 18.98 32.25 12.21 3/8 13 13.31. 11.82 25 17.52.89 2.5 19.1 33.7 12.8 3/8 483 39 5 515-357 482-17.32 21.4 8.47 3.8.2 35.4 13.39 1/2 4 5-13 25 17.52.89 2.5.24 35.95 12.8 3/8 524 72-17 15.75 12.25 13.78.32 21.4 8.47 3.8.83 37.29 13.39 1/2 534 575 584 753-33.8 22.4 8.47 3.82 21.58 38.8 13.98 1/2 1 795-17.32 21.4 8.47 3.8 23.23 41.38 13.39 1/2 15.75 13.9 15.75 33.8 22.4 8.47 3.82 23.98 42.17 13.98 1/2 597 753 48 953-711 911-25 42.33 28.55.44 4.77 24.89 44.2 15.3 1/2 88 81-5 25 1.93 19.9 42.33 28.55.44 4.77 28.47 5.3 15.3 1/2 7 1499 775 9-24 28 7 25 42.33 28.55.44 4.77 33.15 58.98 15.3 1/2 24 285-497 815 915 32 53.94 3.23 15.5.3 34.1 1.93 1.93 3/4 295 3131-32 53.94 3.23 15.5.3 37.17.38 1.93 3/4 3314 3894-7 547 7 925 35 5.75 45.28 19.89 7.4 39.1 9.14 17.72 3/4 3732 4312-1) 1.49" (38 mm) for low capacity segment (eg C5-RE) 12 TECHNICAL BULLETIN 12/1

3 R 25 US NELES R-SERIES SEGMENT VALVE Flanged RE and Wafer RE1 RE-B1C INCH DN B1C Dimensions (mm) REC_ASME 15 REC_ASME RE1 NPT Size A C ød F G X V J H Imax øb kg øb kg kg 1 25 2 5 33/38 1) 9 3 2 341 3 1/4 8 11.9 124 11.9 8.2 1.5 114 5 49 9 3 247 357 3 1/4 127 13.5 155 14.3 9.5 2 5 124 91 9 3 258 394 3 1/4 152 1.1 15 1.8 12 2.5 5 97 75 9 3 25 4 3 1/4 185 18 - - - 3 8 15 8 89 9 3 443 3 1/4 191 21 2 2 18 4 194 1 113 9 3 299 44 3 1/4 229 28.3 254 34.3 22 9 3 348 57 3 1/4 4.3 51.3 15 9 229 174 14 455 315 1 43 349 578 5 1/4 279 52 318 57 5 11 5 375 135 5 355 597 3 3/8 59 4 55 9 3 3 49 3 1/4 9 9 7 8 9 243 1 5 455 315 1 43 4 5 1/4 343 75 381 9 71 11 5 375 135 51 4 79 3 3/8 82 3 8 9 455 315 1 43 44 752 3 1/4 4 152-25 11 5 375 135 51 452 771 3 3/8 114 159-297 251 259 45 13 35 445 175 5 48 87 325 3/8 139 174-17 77 545 215 78 483 842 3 1/2 12 197-11 5 375 135 51 482 819 3 3/8 12 219-12 13 338 29 35 445 175 5 498 855 325 3/8 483 177 5 234-17 77 545 215 78 513 89 3 1/2 257-13 35 445 175 5 514 913 325 3/8 238 319-14 35 17 311 35 77 545 215 78 529 947 3 1/2 534 21 584 342-8 575 215 97 548 97 355 1/2 28 31-17 77 545 215 78 59 51 3 1/2 323 414-1 353 8 575 215 97 9 71 355 1/2 597 342 48 433-25 75 725 25 121 32 1118 39 1/2 491-5 25 58 4 5 75 725 25 121 723 128 39 1/2 7 81 775 731-24 25 75 725 25 121 842 1498 39 1/2 1 1298-497 815 915 32 137 9 395 153 879 1573 4 3/4 1225 1423-28 7 32 137 9 395 153 944 18 4 3/4 15 177-7 547 7 925 35 17 115 55 194 993 175 45 3/4 19 19-1) 1.49" (38 mm) for low capacity segment (eg C5-RE) TECHNICAL BULLETIN 12/1 13

METSO 3 R 25 US RE-B1J / B1JA MOUNTING POSITION A (STANDARD) NPT X NPT ød G F SUPPLY G 1/4 A A1 SIGNAL M X 1.5 V NPS øb (only RE) C J I H FLOW DIRECTION RE-B1J / B1JA INCH DN B1J / B1JA Dimensions (inch) REC_ASME 15 REC_ASME RE1 NPT Size A C ød F G X V J H Imax øb lbs øb lbs lbs 1 25 4.2 2.21 1.29/1.49 1) 19.1 14.49 4.34 1.42 9.41 13.8 12.1 3/8 47 47 38 4.2 4.89 8 22.5 1.54 5.32 1.7 9.45 14.34 12.1 3/8 55 55 47 1.5 19.1 14.49 4.34 1.42 9.9 14.49 12.1 3/8 51 53 42 4.49 2.5 1.93 5.11 8 22.5 1.54 5.32 1.7 9.73 14.97 12.1 3/8 2 51 2 5 19.1 14.49 4.34 1.42.12 15.91 12.1 3/8 55 58 44 4.89 3.59 2.37 5.99.5 8 22.5 1.54 5.32 1.7.1 1.38 12.1 3/8 4 55 2.5 5 19.1 14.49 4.34 1.42.4 1.4 12.1 3/8 58 - - 5.71 3.82 2.9 7.29-8 22.5 1.54 5.32 1.7.44 1.93 12.1 3/8 - - 3 8 19.1 14.49 4.34 1.42 11.38 17.88 12.1 3/8 77 58.5 4.2 3.51 7.52 8.27 8 22.5 1.54 5.32 1.7 11.42 18.35 12.1 3/8 75 8 4 19.1 14.49 4.34 1.42 11.74 18.71 12.1 3/8 84 95 9 7.4 4.73 4.45 9.2 8 22.5 1.54 5.32 1.7 11.78 19.18 12.1 3/8 93 4 77 19.1 14.49 4.34 1.42 13.7 22.7 12.1 3/8 121 135 113 15 8 9.2.8.4 22.5 1.54 5.32 1.7 13.71 23.23 12.1 3/8.99 1 12.52 143 121 25. 19.3.89 2.1 13.98 24.3 8.8 3/8 159 17 154 19.1 14.49 4.34 1.42 15.87 2.3 12.1 3/8 172 218 15 8 8 22.5 1.54 5.32 1.7 15.91 2.5 12.1 3/8 181 227 17 9.57 7.92 8.8 13.51 15 25. 19.3.89 2.1 1.15 27.5 12.21 3/8 9 25 9 12 31.5 24.41 8.47 2.5 1.78 28.98 9.2 1/2 271 317 24 25. 19.3.89 2.1 17.8 31.11 12.21 3/8 273 379-25 12 11.7 9.89.2 31.5 24.41 8.47 2.5 18.43 32.5 12.8 1/2 15.99 319 17.72 4-1 38.98 29.93.44 3.8 19.2 34.14 13.39 1/2 48 557-12 31.5 24.41 8.47 2.5 19.1 34.45 12.8 1/2 447 572-12 1 13.31. 11.82 38.98 29.93.44 3.8.2 3.7 13.39 1/2 19.2 542.48 7-47.25 3.82 15.5 3.82 21.3 39.38.3 3/4 77 832-14 35 1 38.98 29.93.44 3.8.83 38.31 13.39 1/2 7 854-15.75 12.25 13.78 21.3 23 47.25 3.82 15.5 3.82 21.58 41.2 13.98 3/4 841 19-1 47.25 3.82 15.5 3.82 23.98 45.71 13.98 3/4 977 1177-15.75 13.9 15.75 23.51 25.52 25.24 47.25 19.89 4.77 24.89 48.75 15.3 3/4 134 155-5 25 1.93 19.9.24 47.25 19.89 4.77 28.47 55.3 15.3 3/4 27.52 198.52 9-24 32 24.2 19.57 23.3 74.22 5.5 21.2.3 34.1 2.9 1.82 1 32.9 8 3.3 44-28 7 32 27.9 21.54 27.5 74.22 5.5 21.2.3 37.13.58 1.82 1 3.42 4227.75 487-1) 1.49" (38 mm) for low capacity segment (eg C5-RE) 14 TECHNICAL BULLETIN 12/1

3 R 25 US NELES R-SERIES SEGMENT VALVE Flanged RE and Wafer RE1 RE-B1J / B1JA INCH DN B1J / B1JA Dimensions (mm) REC_ASME 15 REC_ASME RE1 NPT Size A C ød F G X V J H Imax øb kg øb kg kg 1 25 2 5 33/38 1) 485 38 1 3 239 352 5 3/8 21 21 17 8 124 8 5 4 135 43 2 34 5 3/8 25 25 21 1.5 485 38 1 3 24 38 5 3/8 23 24 19 114 5 49 127 155 8 5 4 135 43 247 38 5 3/8 27 28 23 2 5 485 38 1 3 257 4 5 3/8 25 2 124 91 152 15 8 5 4 135 43 258 41 5 3/8 29 25 2.5 5 485 38 1 3 24 418 5 3/8 2 - - 97 75 185-8 5 4 135 43 25 4 5 3/8 - - 3 8 485 38 1 3 289 454 5 3/8 35 2 15 8 89 191 2 8 5 4 135 43 4 5 3/8 34 39 4 485 38 1 3 298 475 5 3/8 38 43 31 194 1 113 229 254 8 5 4 135 43 299 487 5 3/8 42 47 35 485 38 1 3 347 578 5 3/8 55 1 51 15 8 229 174 14 5 4 135 43 348 59 5 3/8 279 59 318 5 55 5 49 175 51 355 17 225 3/8 72 77 7 485 38 1 3 3 1 5 3/8 78 99 75 8 8 5 4 135 43 4 73 5 3/8 82 3 8 243 1 5 343 381 5 49 175 51 4 7 3 3/8 95 11 95 12 8 215 5 42 73 235 1/2 123 144 1 5 49 175 51 452 79 3 3/8 124 172-25 12 297 251 259 8 215 5 48 827 325 1/2 45-1 99 7 25 78 483 87 3 1/2 218 253-12 8 215 5 498 875 325 1/2 3-12 1 338 29 99 7 25 78 513 91 3 1/2 483 24 5 3-1 935 395 97 534 27 3/4 321 378-14 35 1 99 7 25 78 529 973 3 1/2 7 388-311 35 534 584 1 935 395 97 548 57 355 3/4 382 43-1 1 935 395 97 9 111 355 3/4 444 535-353 597 48 25 15 1 55 121 32 1238 39 3/4 711-5 25 58 4 5 15 1 55 121 723 1 39 3/4 99 9 775 95-24 32 497 1885 1 5 153 879 1577 427 1 815 1 915 1838-28 7 32 7 547 7 1885 1 5 153 943 191 427 1 925 1921 35 2185-1) 1.49" (38 mm) for low capacity segment (eg C5-RE) TECHNICAL BULLETIN 12/1 15

HOW TO ORDER Example: 1. 2. 3. 4. 5.. 7. 8. 9.. 11. - RE1 D A 3 D J J S T / - 1. Sign Trim codes --- standard V-port (no sign) Q- Low noise and anti-cavitation trim (for 2" and larger) C5- Maximum Cv =.5 (for 1" only) C15- Maximum Cv = 1.5 (for 1" only) C5- Maximum Cv = 5. (for 1" only) C15- Maximum Cv = 15. (for 1" only) 2. Sign Product series RE1 Flangeless body, face-to-face acc. to ISA S75.4 and DIN/IEC 534 Part 3-2. (Available in sizes 1" - 8") Flanged body, face-to-face acc. to ASME B1. ( spool piece RE13 constr.) (Available in sizes 1" - 12") RE Flanged body, face-to-face acc. to ISA S75.4 and DIN/IEC Part 3-2. (Available in sizes 1" - 32") 3. Sign Pressure rating (Note: See table 1 on page 3) C ASME 15 D ASME For RE1D use sign "D" for both 15# and # valves. 7. Sign Segment materials J Type AISI 329+HCr; ANSI 31+HCr for low Cv segments C CG8M + HCr S Type AISI 329 ( without chrome ). Used with soft seats, eg. RECA_CSJT2T 8. Sign Shaft, pin & bearing materials J Type AISI 329 Drive Shaft & PTFE on SS 31 net S 17-4 PH / Cobalt (2" - ") 9. Sign Seat design and materials 31 SS + cobalt based hard facing High temp. metal seat (2"- A ") only Stainless Steel+Cobalt Hard facing, S Inconel 25 spring, Filled PTFE/Elgiloy lipseal, - F +48 F ANSI/FCI 7-2 class IV, General services T2 Stainless Steel with PTFE+C25 % insert Cobalt based alloy, - F +48 F E Non-tight, extremely erosive services. 1S 31 SS + Cobalt based hard facing, 2-way metal seat 4. Sign Construction (Note: See table 2 on page 3) A Standard, drive shaft with ANSI keyway to actuator 5. Sign Size Inch 1", 1 1/2", 2", 2 1/2", 3", 4", ", 8", ", 12", 14", 1", ", 24", 28",32". Sign Body, blind flange & screw materials ASTM A351 gr. CF8M (standard for sizes 12" and larger as well A as # Class Flanged models) ASTM A21 gr. WCB / 1-19 (blind flange & gland bolting A4- D 8, corresponds to B8M) ASTM A351 gr. CG8M (blind flange & gland bolting A4-8, C corresponds to B8M) Note:- Gland material is always CF8M. Sign T G Stem packing & blind flange seal PTFE V-rings, live-loaded Graphite rings, live loaded (fire-safe) 11. Model Code Sign - Version A Version A -availability for high temperature construction 12. Sign / - Flange facing ASME B1.5 (Ra 3.2.3 / RMS 125-25) Cover EN92-1 Type B1 Subject to change without prior notice. Metso Flow Control Inc. Europe, Vanha Porvoontie 229, P.O. Box 4, FI-11 VANTAA, Finland. Tel. +358 483 15. Fax +358 483 151 North America, 44 Bowditch Drive, P.O. Box 844, Shrewsbury, MA 1545, USA. Tel. +1 58 852. Fax +1 58 852 8172 South America, Av. Independéncia, 25- Iporanga, 1887-1, Sorocaba-São Paulo, Brazil. Tel. +55 15 22 97. Fax +55 15 22 9748/49 Asia Pacific, 238B Thomson Road, #17-1 Novena Square Tower B, Singapore 785. Tel. +5 511 11. Fax +5 25 8 China, 11/F, China Youth Plaza, No.19 North Rd of East 3rd Ring Rd, Chaoyang District, Beijing, China. Tel. +8 5. Fax +8 5 2583. Middle East, Roundabout 8, Unit AB-7, P.O. Box 17175, Jebel Ali Freezone, Dubai, United Arab Emirates. Tel. +971 4 883 974. Fax +971 4 883 83 www.metso.com/valves