Parts Manual for MID-MOUNT ZERO TURNING HYDRO DRIVE SERIES 0 & 1 MODEL CZT19480KWV CZT19481KWV HZT21480BV HZT21481BV McDonough, GA, 30253 U.S.A. Briggs & Startton Yard Power Products Group Copyright 2007 Briggs & Startton Corporation Milwaukee, WI USA. All Rights Reserved Revision 3, 4/26/2007 Manual No. 7006935
Table Of Contents PAGE GROUP 4 CASTER WHEEL ASSEMBLY 6 DRIVE TIRE & WHEEL ASSEMBLY 8 FRAME ASSEMBLY 10 FUEL TANK ASSEMBLY, LH 12 FUEL TANK ASSEMBLY, RH (Series 0) 14 FUEL TANK ASSEMBLY, RH (Series 1) 16 SEAT ASSEMBLY (Ferris) 18 SEAT ASSEMBLY (Milsco) 20 MUFFLER GUARD ASSEMBLY 22 TWIN STICK CONTROL ASSEMBLY (R.H.) 24 TWIN STICK CONTROL ASSEMBLY (L.H.) 26 PARKING BRAKE ASSEMBLY 28 LIFT SYSTEM ASSEMBLY 30 ENGINE SUB-ASSEMBLY 32 HYDRO IDLER ASSEMBLY 34 PUMPS, PULLEYS & MOTORS 36 HYDRO RESERVOIR & FILTER ASSEMBLY 38 ROLL BAR PROTECTIVE STRUCTURE 40 48" CUTTING DECK ASSEMBLY (Sub Assy) 42 48" CUTTING DECK ASSEMBLY (Final Assy) 44 48" SPINDLE ASSEMBLY 46 DECALS 48 CONTROL PANEL ASSEMBLY 50 ELECTRICAL COMPONENTS (except wiring) 52 WIRING HARNESS (Briggs Engines) 54 WIRING HARNESS (Kawasaki Engines) 56 WIRING SCHEMATIC (Briggs) 58 WIRING SCHEMATIC (Kawasaki) MID-MOUNT SERIES 0 & 1 3 Manual No. 7006935
CASTER WHEEL ASSEMBLY Manual No. 7006935 MID-MOUNT 4 SERIES 0 & 1
CASTER WHEEL ASSEMBLY Item Part No Qty Description Note 1 7072730 2 WELDMENT, Caster (Black textured) used on CZT models 1 7400052 2 WELDMENT, Caster (Red) used on HZT models 2 7012709 2 RING, 1 External Retaining 3 7091772 2 SCREW, 7/16-14 x 6 Hex Head Cap, GR 5 4 7091917 2 NUT, 7/16-14 Hex Nyloc 5 7023747 2 BUSHING, 1 Machine 6 7035359 2 TUBE, Caster Wheel (5/8 O.D. x 4.510) 7 7029141 2 BALL BEARING, Flanged, 1 I. D. x 2 x 5/8 LUTCO #64F64P2 8 7059090 2 ASSY, Front Wheel & Tire (incl. items 9-13) 9 7012234 1 AIR VALVE STEM & CAP, Snap-In 10 7035358 2 BALL BEARING,.625 I.D. x 1.38 11 7035618 1 TIRE, 11 x 4.00-5, Smooth Tread 12 7039477 1 RIM, 5.00 Dia. x 3.00 13 7029275 1 FITTING, Lube (1/4-28 thread) ALEMITE #3038-B 14 7090361 2 SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap 15 7036578 2 CAP, Caster Shaft (Black) used on CZT models 15 7300190 2 CAP, Caster Shaft (Red) used on HZT models 16 7074720 2 BUSHING, Idler PM Footnotes: MID-MOUNT SERIES 0 & 1 5 Manual No. 7006935
DRIVE TIRE & WHEEL ASSEMBLY Manual No. 7006935 MID-MOUNT 6 SERIES 0 & 1
DRIVE TIRE & WHEEL ASSEMBLY Item Part No Qty Description Note 1 7071838 2 WHEEL ASSY, 20 x 10-10 4 Ply used on HZT models (incl. items 2A, 3A & 4) 1 7100110 2 WHEEL ASSY, 22 x 10-10 4 Ply used on CZT models (incl. items 2B, 3B & 4) 2A 7071837 1 TIRE, 20 x 10-10 4 Ply 2B 7100209 1 TIRE, 22 x 10-10 4 Ply Turfmaster 3A 7071836 1 RIM, 10 x 7.00 4/4 3B 7100208 1 RIM, 10 x 7.00 4 7012234 1 VALVE STEM & CAP 5 7027192 8 LUG NUT, 1/2-20 Tapered Seat 6 7078222 2 BRAKE DRUM also shown on Parking Break Assembly page 7 7091793 PIN, 9/64 x 1-1/2 Cotter included as part of wheel motor 8 7013861 KEY, #11 Woodruff included as part of wheel motor 9 7091828 NUT, 3/4-20 Slotted Hex included as part of wheel motor Footnotes: MID-MOUNT SERIES 0 & 1 7 Manual No. 7006935
FRAME ASSEMBLY Manual No. 7006935 MID-MOUNT 8 SERIES 0 & 1
FRAME ASSEMBLY Item Part No Qty Description Note 1 7072786 1 WELDMENT, Frame (Black Textured Finish) used on CZT19480KWV 1 7400064 1 WELDMENT, Frame (Black Textured Finish) used on CZT19481KWV 1 7050442 1 WELDMENT, Frame (Red Finish) used on HZT21480BV 1 7400065 1 WELDMENT, Frame (Red Finish) used on HZT21481BV 2 7072523 1 WELDMENT, Pusher Bar 3 7091328 4 SCREW, 3/8-16 x 1-1/4 Hex Head Cap, GR 5 4 7091299 4 NUT, 3/8-16 Hex Nyloc 5 7034087 1 PLATE, Frame Support 6 7090361 4 SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap 7 7078220 1 FAN GUARD 8 7091318 2 SCREW, 5/16-18 x 3/4 Hex Head Cap, GR 5 9 7090188 4 WASHER, 5/16 Flat 10 7091298 2 NUT, 5/16-18 Hex Nyloc 11 7078171 1 MAT, Floorpan, CZT 12 7078181 1 MAT, Footrest, CZT 13 7045151 1 FLOORPAN 14 7041818 2 PAD, Floor Pan 15 7014669 2 LUBE FITTING, 3/16 Footnotes: MID-MOUNT SERIES 0 & 1 9 Manual No. 7006935
FUEL TANK ASSEMBLY, LH Manual No. 7006935 MID-MOUNT 10 SERIES 0 & 1
FUEL TANK ASSEMBLY, LH Item Part No Qty Description Note 1 7092089 3 SCREW, 7/16-14 x 2 Hex Head Cap, GR 5 2 7090250 3 WASHER, 1/2 Flat SAE 3 7091917 3 NUT, 7/16-14 Hex Nyloc 4 7027175 1 BOLT, 5/16-18 x 2-1/2 Hex Head w/lock patch 5 7090188 1 WASHER, 5/16 Flat 6 7091298 1 NUT, 5/16-18 Hex Nyloc 7 7050443 1 ASSEMBLY, L.H. Tank CZT (incl. 6 items shown below) 7A 7042924 1 FUEL TANK, LH (SNAPPER PRO printed on tank) 7B 7075135 1 CAP, Fuel, 3-1/2 Kelch part no. 201906 7C 7074835 1 ELBOW, 90-degree Dapco part no. 11942 7D 7046804 1 DIP TUBE,.261 I.D. x 24-1/4 7E 7012337 1 GROMMET, Dip Tube Dapco part no. 10672 7F 3 SPACER 8 7050445 1 ASSEMBLY, L. H. Tank HZT (incl. 6 items shown below) 8A 7078035 FUEL TANK, LH (SNAPPER printed on tank) 8B 7075135 1 CAP, Fuel, 3-1/2 Kelch part no. 201906 8C 7074835 1 ELBOW, 90-degree Dapco part no. 11942 8D 7046804 1 DIP TUBE,.261 I.D. x 24-1/4 8E 7012337 1 GROMMET, Dip Tube Dapco part no. 10672 8F 3 SPACER 9 7074687 2 BRACKET, Auxiliary Fuel Valve 10 7012222 6 CLAMP, Fuel Hose 11A 7078221 1 FUEL HOSE, 1/4 I. D. x 49 (RH) 11B 7033693 1 FUEL HOSE, 1/4 I.D. x 17 long 11C 7074690 1 FUEL HOSE, 1/4 I.D. x 1' Long 12 7044681 1 ASSEMBLY, 3-Way Fuel Valve 13 7091640 5 BOLT, 3/8-16 x 1 Square Neck Carriage, GR 5 14 7091299 5 NUT, 3/8-16 Hex Nyloc 15 7053476 1 WELDMENT, L.H. Tank Bracket 16 7015861 1 CLIP, Harness 17 7091909 1 WELL-NUT, 1/4-20 x 53/64 18 7012080 5 CABLE TIE, 7 not shown Footnotes: MID-MOUNT SERIES 0 & 1 11 Manual No. 7006935
FUEL TANK ASSEMBLY, RH (Series 0) Manual No. 7006935 MID-MOUNT 12 SERIES 0 & 1
FUEL TANK ASSEMBLY, RH (Series 0) Item Part No Qty Description Note 1 7092089 3 SCREW, 7/16-14 x 2 Hex Head Cap, GR 5 2 7090250 3 WASHER, 1/2 Flat SAE 3 7091917 3 NUT, 7/16-14 Hex Nyloc 4 7027175 1 BOLT, 5/16-18 x 2-1/2 Hex Head w/lock patch 5 7090188 1 WASHER, 5/16 Flat 6 7091298 1 NUT, 5/16-18 Hex Nyloc 7 7050444 1 ASSEMBLY, R.H. Tank CZT (incl. 10 items shown below) 7a 7042925 1 FUEL TANK, RH (SNAPPER PRO printed on tank) 7b 7075135 1 CAP, Fuel, 3-1/2 Kelch part no. 201906 7c 7074835 1 ELBOW, 90-degree Dapco part no. 11942 7d 7046804 1 DIP TUBE,.261 I.D. x 24-1/4 7e 7012337 1 GROMMET, Dip Tube Dapco part no. 10672 7f 3 SPACER 7g 7090825 2 SCREW, 1/4-20 x 1-1/4 Hex Head Cap, GR 5 7h 7027223 2 WASHER, 1/4 Split Lock 7i 7091294 2 WASHER, 1/4 Flat 7j 7046324 1 LID, Fuel Tank NOTE: Warning text is printed on part. 8 7050446 1 ASSEMBLY, R. H. Tank HZT (incl. 10 items shown below) 8a 7078036 1 FUEL TANK, RH (SNAPPER printed on tank) 8b 7075135 1 CAP, Fuel, 3-1/2 Kelch part no. 201906 8c 7074835 1 ELBOW, 90-degree Dapco part no. 11942 8d 7046804 1 DIP TUBE,.261 I.D. x 24-1/4 8e 7012337 1 GROMMET, Dip Tube Dapco part no. 10672 8f 3 SPACER 8g 7090825 2 SCREW, 1/4-20 x 1-1/4 Hex Head Cap, GR 5 8h 7027223 2 WASHER, 1/4 Split Lock 8i 7091294 2 WASHER, 1/4 Flat 8j 7046324 1 LID, Fuel Tank NOTE: Warning text is printed on part. 9 7091640 5 BOLT, 3/8-16 x 1 Square Neck Carriage, GR 5 10 7091299 5 NUT, 3/8-16 Hex Nyloc 11 7053518 1 WELDMENT, R.H. Tank Bracket 12 7074687 1 BRACKET, Auxiliary Fuel Valve 13 7091909 1 WELL-NUT, 1/4-20 x 53/64 Footnotes: MID-MOUNT SERIES 0 & 1 13 Manual No. 7006935
FUEL TANK ASSEMBLY, RH (Series 1) Manual No. 7006935 MID-MOUNT 14 SERIES 0 & 1
FUEL TANK ASSEMBLY, RH (Series 1) Item Part No Qty Description Note 1 7092089 3 SCREW, 7/16-14 x 2 Hex Head Cap, GR 5 2 7090250 3 WASHER, 1/2 Flat SAE 3 7091917 3 NUT, 7/16-14 Hex Nyloc 4 7027175 1 BOLT, 5/16-18 x 2-1/2 Hex Head w/lock patch 5 7090188 1 WASHER, 5/16 Flat 6 7091298 1 NUT, 5/16-18 Hex Nyloc 7 7100214 1 ASSEMBLY, R.H. Tank CZT (incl. 10 items shown below) 7a 7042925 1 FUEL TANK, RH (SNAPPER PRO printed on tank) 7b 7075135 1 CAP, Fuel, 3-1/2 Kelch part no. 201906 7c 7074835 1 ELBOW, 90-degree Dapco part no. 11942 7d 7046804 1 DIP TUBE,.261 I.D. x 24-1/4 7e 7012337 1 GROMMET, Dip Tube Dapco part no. 10672 7f 3 SPACER 7g 7090825 2 SCREW, 1/4-20 x 1-1/4 Hex Head Cap, GR 5 7h 7027223 2 WASHER, 1/4 Split Lock 7i 7091294 2 WASHER, 1/4 Flat 7j 7100211 1 LID, Fuel Tank NOTE: Warning text is printed on part in English and Spanish. 8 7100216 1 ASSEMBLY, R. H. Tank HZT (incl. 10 items shown below) 8a 7078036 1 FUEL TANK, RH (SNAPPER printed on tank) 8b 7075135 1 CAP, Fuel, 3-1/2 Kelch part no. 201906 8c 7074835 1 ELBOW, 90-degree Dapco part no. 11942 8d 7046804 1 DIP TUBE,.261 I.D. x 24-1/4 8e 7012337 1 GROMMET, Dip Tube Dapco part no. 10672 8f 3 SPACER 8g 7090825 2 SCREW, 1/4-20 x 1-1/4 Hex Head Cap, GR 5 8h 7027223 2 WASHER, 1/4 Split Lock 8i 7091294 2 WASHER, 1/4 Flat 8j 7100212 1 LID, Fuel Tank NOTE: Warning text is printed on part. 9 7091640 5 BOLT, 3/8-16 x 1 Square Neck Carriage, GR 5 10 7091299 5 NUT, 3/8-16 Hex Nyloc 11 7053518 1 WELDMENT, R.H. Tank Bracket 12 7074687 1 BRACKET, Auxiliary Fuel Valve 13 7091909 1 WELL-NUT, 1/4-20 x 53/64 Footnotes: MID-MOUNT SERIES 0 & 1 15 Manual No. 7006935
SEAT ASSEMBLY (Ferris) Manual No. 7006935 MID-MOUNT 16 SERIES 0 & 1
SEAT ASSEMBLY (Ferris) Item Part No Qty Description Note 1 5023184 1 * SEAT (Ferris) (Milsco # 5673089BB Model XB- 180) used on HZT21480BV 2 7046303 1 SEAT PLATE 3 7046269 1 PIVOT BRACKET, Seat Hinge 4 7045149 1 CROSS PLATE 5 7023191 2 KNOB, Three Prong (5/16-18) 6 7090187 2 WASHER, 5/16 Split Lock 7 7013849 2 SPACER,.33 x.63 x.156 8 7091038 2 SCREW, 5/16-18 x 1/2 Hex Washer Machine w/nyloc Patch 9 7015761 2 SHOULDER BOLT, 5/16-18 10 7090951 2 NUT, 5/16-18 Large Flange Hex Center Lock 11 7091640 5 BOLT, 3/8-16 x 1 Square Neck Carriage, GR 5 12 7091299 5 NUT, 3/8-16 Hex Nyloc 13 7090361 4 SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap 14 7074218 2 SPRING, Compression- Seat Support 15 7090122 2 WASHER, 3/8 SAE Flat 16 1716368 1 ASSEMBLY, Seat Switch (NC) (includes switch p/n 17590) 17 1960536 2 SCREW Footnotes: Note* For Arm Rest components contact Milsco, P.O. Box 245021 909 N. 51st Street Milwaukee, WI 53224 ph. 414-354- 0500 MID-MOUNT SERIES 0 & 1 17 Manual No. 7006935
SEAT ASSEMBLY (Milsco) Manual No. 7006935 MID-MOUNT 18 SERIES 0 & 1
SEAT ASSEMBLY (Milsco) Item Part No Qty Description Note 1 7071841 1 * SEAT (Milsco) w/ Urban Gray Vinyl (Milsco # 06632A) used on CZT19480KWV 2 7046303 1 SEAT PLATE 3 7046269 1 PIVOT BRACKET, Seat Hinge 4 7045149 1 CROSS PLATE 5 7023191 2 KNOB, Three Prong (5/16-18) 6 7090187 2 WASHER, 5/16 Split Lock 7 7013849 2 SPACER,.33 x.63 x.156 8 7091038 2 SCREW, 5/16-18 x 1/2 Hex Washer Machine w/nyloc Patch 9 7015761 2 SHOULDER BOLT, 5/16-18 10 7090951 2 NUT, 5/16-18 Large Flange Hex Center Lock 11 7091640 5 BOLT, 3/8-16 x 1 Square Neck Carriage, GR 5 12 7091299 5 NUT, 3/8-16 Hex Nyloc 13 7090361 4 SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap 14 7074218 2 SPRING, Compression- Seat Support 15 7090122 2 WASHER, 3/8 SAE Flat 16 1716368 1 ASSEMBLY, Seat Switch (NC) (includes switch p/n 17590) 17 1960536 2 SCREW Footnotes: Note* For Arm Rest components contact Milsco, P.O. Box 245021 909 N. 51st Street Milwaukee, WI 53224 ph. 414-354- 0500 MID-MOUNT SERIES 0 & 1 19 Manual No. 7006935
MUFFLER GUARD ASSEMBLY Manual No. 7006935 MID-MOUNT 20 SERIES 0 & 1
MUFFLER GUARD ASSEMBLY Item Part No Qty Description Note 1 7041929 2 BRACKET, Lower Guard Mount 2 7041930 2 BRACKET, Upper Guard Mount 3 7074143 1 REAR SUPPORT, Muffler Guard 4 7074693 1 BACK PLATE, Muffler Guard 5 7075073 1 GUARD, Muffler 6 7091299 20 NUT, 3/8-16 Hex Nyloc 7 7091640 20 BOLT, 3/8-16 x 1 Square Neck Carriage, GR 5 Footnotes: MID-MOUNT SERIES 0 & 1 21 Manual No. 7006935
TWIN STICK CONTROL ASSEMBLY (R.H.) Manual No. 7006935 MID-MOUNT 22 SERIES 0 & 1
TWIN STICK CONTROL ASSEMBLY (R.H.) Item Part No Qty Description Note 1 7015363 2 BEARING, 3/4 I.D. Flange 2 7023355 1 SWITCH, DPDT (NC/NO) 3 7029617 2 WASHER,.77 I.D. Flat 4 7029738 1 RETAINING RING, 3/4 External WALDES #5160-75 5 7034566 1 PLATE, Speed Control 6 5022978 1 DAMPENER, Hydraulic C16-22472 SUPSA 7 7043889 1 COVER, Right Hand 8 7046587 1 TWIN BLOCK 9 7071825 1 BRACKET, Handle Adjustment 10 7071839 1 LEVER 11 7072212 1 GRIP, Twin Stick 12 7072780 1 WELDMENT, Stick Control 13 7075405 1 WELDMENT, Twin Stick 14 1 ASSEMBLY, Pump Control Linkage (Includes item #'s 16, 29 & 30) 15 7074661 1 HANDLEBAR, Twin Stick 16 7074144 1 LINKAGE, Pump Control (5/16-24 threads) per 7059118 linkage assembly 17 7090188 11 WASHER, 5/16 Flat 18 7090361 5 SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap 19 7090585 4 NUT, 5/16-18 Hex Flange Lock 20 7090588 1 SCREW, 3/8-16 x 2 Hex Head Cap, GR 5 21 7090669 4 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 22 7090913 2 SCREW, #10-24 x 1/2 Hex Washer Self-Tap (Torx) 23 7091003 2 SCREW, 1/4-20 x 1-3/4 Hex Head Cap, GR 5 24 7091298 3 NUT, 5/16-18 Hex Nyloc 25 7091299 1 NUT, 3/8-16 Hex Nyloc 26 7091527 1 SCREW, 5/16-18 x 1-1/4 Hex Head Cap, GR 5 27 7091603 2 NUT, 1/4-20 Hex Nyloc 28 7092091 1 GROOVE PIN, 1/4 x 1-1/4 long 29 7027139 2 BALL JOINT, Pump Control Linkage (5/16-24 thread) per 7059118 linkage assembly 30 7091297 2 NUT, 5/16-24 Hex, GR 5 per 7059118 linkage assembly Footnotes: MID-MOUNT SERIES 0 & 1 23 Manual No. 7006935
TWIN STICK CONTROL ASSEMBLY (L.H.) Manual No. 7006935 MID-MOUNT 24 SERIES 0 & 1
TWIN STICK CONTROL ASSEMBLY (L.H.) Item Part No Qty Description Note 1 7015363 2 BEARING, 3/4 I.D. Flange 2 7023355 1 SWITCH- DPDT (NC/NO) 3 7029617 2 WASHER,.77 I.D. Flat 4 7029738 1 RETAINING RING, 3/4 External WALDES #5160-75 5 7034566 1 PLATE, Speed Control 6 7041986 1 COVER, Left Hand 7 5022978 1 DAMPENER, Hydraulic C16-22472 SUPSA 8 7046587 1 TWIN BLOCK 9 7071825 1 BRACKET, Handle Adjustment 10 7071839 1 LEVER 11 7072212 1 GRIP, Twin Stick 12 7072780 1 WELDMENT, Stick Control 13 7072809 1 WELDMENT, Twin Stick 14 1 ASSEMBLY, Pump Control Linkage (Includes item #'s 16, 29 & 30) 15 7074661 1 HANDLEBAR, Twin Stick 16 7074144 1 LINKAGE, Pump Control (5/16-24 threads) per 7059118 linkage assembly 17 7090188 9 WASHER, 5/16 Flat 18 7090361 5 SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap 19 7090585 4 NUT, 5/16-18 Hex Flange Lock 20 7090588 1 SCREW, 3/8-16 x 2 Hex Head Cap, GR 5 21 7090669 4 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 22 7090913 2 SCREW, #10-24 x 1/2 Hex Washer Self-Tap (Torx) 23 7091003 2 SCREW, 1/4-20 x 1-3/4 Hex Head Cap, GR 5 24 7091298 3 NUT, 5/16-18 Hex Nyloc 25 7091299 1 NUT, 3/8-16 Hex Nyloc 26 7091527 1 SCREW, 5/16-18 x 1-1/4 Hex Head Cap, GR 5 27 7091603 2 NUT, 1/4-20 Hex Nyloc 28 7092091 1 GROOVE PIN, 1/4 x 1-1/4 long 29 7027139 2 BALL JOINT, Pump Control Linkage (5/16-24 thread) per 7059118 linkage assembly 30 7091297 2 NUT, 5/16-24 Hex, GR 5 per 7059118 linkage assembly Footnotes: MID-MOUNT SERIES 0 & 1 25 Manual No. 7006935
PARKING BRAKE ASSEMBLY Manual No. 7006935 MID-MOUNT 26 SERIES 0 & 1
PARKING BRAKE ASSEMBLY Item Part No Qty Description Note 1 7010935 6 WASHER,.77 I.D. Flat 2 7015363 4 BEARING, 3/4 I.D. Flange 3 7091593 4 PIN, 3/8 Self Locking Cotter Was 24159 4 7024586 1 SWIVEL, Brake Link-PM 5 7028620 2 SPACER,.340 I.D. x.63 O.D. x.310 Thick 6 7010746 2 RETAINING RING, 3/4 External Was 29738, WALDES #5160-75 7 7041915 2 BRACKET, Brake 8 7046299 2 ROD, Brake Adjustment (3/8-16 thread) 9 7046692 1 BRACKET, Brake Support 10 7046835 1 LINKAGE, Park Brake (3/8-16 thread) 11 7072727 1 WELDMENT, Brake Rod 12 7072728 2 WELDMENT, Brake Hub Rear 13 7072813 1 WELDMENT, Brake Handle 14 7078222 2 BRAKE DRUM 15 7078223 2 ASSEMBLY, Brake Hub 16 7078238 2 SPRING, Brake 17 7078252 2 BRAKE ASSY, (6 inch) 18 7090122 9 WASHER, 3/8 SAE Flat 19 7090187 8 WASHER, 5/16 Split Lock 20 7091122 2 SCREW, 1/4-20 x 1/2 Hex Washer Self-Tap Was 90539 21 7027168 10 SCREW 5/16-18 x 1 Hex Head Cap, GR 5 Was 90636 22 7091298 2 NUT, 5/16-18 Hex Nyloc 23 7091299 3 NUT, 3/8-16 Hex Nyloc 24 7092091 4 GROOVE PIN, 1/4 x 1-1/4 long 25 1722302 1 HANDLE GRIP (Simplicity) 26 7023355 1 SWITCH- DPDT (NC/NO) 27 7090913 2 SCREW, #10-24 x 1/2 Hex Washer Self-Tap (Torx) Footnotes: MID-MOUNT SERIES 0 & 1 27 Manual No. 7006935
LIFT SYSTEM ASSEMBLY Manual No. 7006935 MID-MOUNT 28 SERIES 0 & 1
LIFT SYSTEM ASSEMBLY Item Part No Qty Description Note 1 7010746 1 RING, 3/4 External Retaining 2 7010935 1 WASHER,.77 I.D. Flat 3 7012802 2 PIN, 1/2 x 1-1/8 Clevis 4 7014669 1 LUBE FITTING, 3/16 5 7043200 1 LINK, Lift 6 7043803 4 BRACKET, Deck Support 7 7044870 8 SHIM PLATE 8 7045115 1 PLATE, Height Support 9 7046156 1 TIE ROD, Lift (1/2-13 thread) 10 7053562 2 ASSY, Chain and Eyebolt 11 7059173 2 CHAIN LINKS 12 7072731 1 WELDMENT, Deck Lift Front 13 7072909 1 WELDMENT, Deck Lift Rear 14 7073429 1 WELDMENT, Deck Handle Support 15 7074580 2 SPACER, Lift Adjuster 16 7074716 1 CLIP, 1/2 Roll Pin 17 7075086 1 TETHER STRAP 18 7075320 1 WELDMENT, Lift Arm 19 7075330 1 GRIP (Plastic Cover) 20 7075782 2 SWIVEL, Rod (1/2-13 thread) or 44858 21 7090361 5 SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap 22 7090543 4 SCREW, 1/2-13 x 2 Hex Head Cap, GR 5 23 7091298 8 NUT, 5/16-18 Hex Nyloc 24 7091299 2 NUT, 3/8-16 Hex Nyloc 25 7091501 2 SCREW, 3/8-16 x 2-1/2 Hex Head Cap, GR 5 26 7091516 2 COTTER PIN, 5/32 x 1 27 7091544 10 NUT, 1/2-13 Hex Flange Lock, GR 5 28 7091587 4 WASHER,.531 I.D. Flat 29 7091894 3 NUT, 1/2-13 Hex Center Lock, GR 5 30 7091928 8 BOLT, 5/16-18 x 1-1/4 Square Neck Carriage, GR 5 Footnotes: MID-MOUNT SERIES 0 & 1 29 Manual No. 7006935
ENGINE SUB-ASSEMBLY Manual No. 7006935 MID-MOUNT 30 SERIES 0 & 1
ENGINE SUB-ASSEMBLY Item Part No Qty Description Note 1 1 * ENGINE 19 HP Vert Shaft, Kawasaki Elec. Start Mod. FH580V- (shown) AS01 1 1 * ENGINE 19 HP Vert Shaft, Kawasaki Elec. Start Mod. FH580V- KAI BS31R 1 1 * ENGINE 21 HP Briggs & Stratton Mod. 385777-0115-E1 (not shown) 2 7027972 1 ASSEMBLY, Oil Valve 3 7091706 5 NUT, 5/16-18 Hex Top Lock, GR B 4 7078234 1 CLAMP ASSEMBLY used on Briggs engines only 5 7091928 1 BOLT, 5/16-18 x 1-1/4 Square Neck Carriage, GR 5 6 7091601 1 NUT, 5/16-18 Hex Flange, GR 5 7 7078154 1 MUFFLER used on Kawasaki engines only 8 7091640 2 BOLT, 3/8-16 x 1 Square Neck Carriage, GR 5 9 7090188 4 WASHER, 5/16 Flat 10 7091540 4 SCREW, 5/16-18 x 1-1/2 Hex Head Cap, GR 5 11 7078270 1 KEY, 1/4 Square x 3-1/4 Long 12 7059099 1 PULLEY, Engine, Hydro Drive 13 7034829 1 BRACKET, Clutch 14 7013847 2 RETAINER, 3/8 Bolt 15 7091299 2 NUT, 3/8-16 Hex Nyloc 16 7075672 1 CLUTCH, Electric (Ogura Model # GT2.5-RM01) 17 7029704 1 BUMPER, Electric Clutch 18 7034448 1 WASHER, Rectangular Steel 19 7091527 1 SCREW, 5/16-18 x 1-1/4 Hex Head Cap, GR 5 20 7075082 1 WASHER,.468 x 1.85 x.25 Flat 21 7091301 1 WASHER, 7/16 Split Lock 22 7092071 1 SCREW, 7/16-20 x 2-1/2 Hex Head Cap, GR 5 with locking patch 23 7078297 1 FUEL HOSE, 1/4 I. D. x 2-1/2 24 7029900 2 CLAMP, Fuel Line 25 7074954 1 O-RING Kawasaki p/n 670D-2016 26 7022486 1 OIL DRAIN, Short (.375 NPT) 27 7078134 1 MUFFLER used on Briggs engines only 28 7091021 2 SCREW, 5/16-24 x 3/4 Hex Head Cap, GR 5 29 7078141 1 BRACKET, Muffler (Briggs) 30 7090187 2 WASHER, 5/16 Split Lock 31 7091297 2 NUT, 5/16-24 Hex, GR 5 32 7078060 1 EXHAUST MANIFOLD, Vanguard 33 7078136 1 HEAT SHIELD, Briggs 34 7091016 1 SCREW, 1/4-20 x 5/8 Hex Head Self-Tap w/free spinning washer Footnotes: NOTE: * Purchase engine components directly from engine manufacturer dealer. MID-MOUNT SERIES 0 & 1 31 Manual No. 7006935
HYDRO IDLER ASSEMBLY Manual No. 7006935 MID-MOUNT 32 SERIES 0 & 1
HYDRO IDLER ASSEMBLY Item Part No Qty Description Note 1 7014409 2 BEARING, 9/16 I.D. Flange 2 7014669 1 LUBE FITTING, 3/16 3 7018574 1 FLAT IDLER, 4.12 O.D. 4 7028620 1 SPACER,.340 I.D. x.63 O.D. x.310 Thick 5 7035816 1 IDLER STUD (3/8-24) 6 7059094 1 WELDMENT, Idler Arm Hydro Drive 7 7073992 1 SPRING, Extension 8 7075078 1 SWIVEL, Adjustable 9 7075109 1 * BELT, Traction Drive (HA Section, 47.5 Effective Length) Series 0 Moodels 9 7100177 1 * BELT, Traction Drive (4L Section, 48.3 Effective Length) Series 1 Models 10 7078063 1 EYEBOLT, 5/16-18 11 7090118 1 WASHER, 3/8 Split Lock 12 7090122 3 WASHER, 3/8 SAE Flat 13 7091298 1 NUT, 5/16-18 Hex Nyloc 14 7091497 2 SCREW, 3/8-16 x 1-1/2 Hex Head Cap, GR 5 15 7091503 1 HAIR PIN, 3/32 x 1-1/2 16 7091511 1 NUT, 5/16-18 Hex, GR 5 or B 17 7091585 2 NUT, 3/8-16 Hex Center Lock 18 7091598 1 COTTER PIN, 1/8 x 3/4 19 7091619 1 NUT, 3/8-16 Hex Flange Lock 20 7091630 1 NUT, 3/8-24 Hex, GR B 21 7091804 2 WASHER, 9/16 Flat (Type Narrow) Footnotes: NOTE: * The Snapper part is number stamped on belt. MID-MOUNT SERIES 0 & 1 33 Manual No. 7006935
PUMPS, PULLEYS & MOTORS Manual No. 7006935 MID-MOUNT 34 SERIES 0 & 1
PUMPS, PULLEYS & MOTORS Item Part No Qty Description Note 1 7072522 1 PUMP, Hydro-Gear (Left Hand) BDP-10A-454 W/ RTN in Reverse (PG-3KCC-NC1X-XXX) 2 7072521 1 PUMP, Hydro-Gear (Right Hand) BDP-10A-331, W/ RTN in Reverse (PG-34CC-NE1X-XXX) 3 7027181 4 BOLT, 3/8-16 x 1-1/4 Short Neck Carriage, GR 5 4 7013847 4 RETAINER, 3/8 Bolt 5 7090122 4 WASHER, 3/8 SAE Flat 6 7091299 4 NUT, 3/8-16 Hex Nyloc 7 7074968 2 FAN, 7 Nylon, Counter-Clockwise 8 7034926 4 FITTING, Hydraulic Parker #8 F50X-S 9 7035648 4 FITTING, Hydraulic Parker #8-10 F50X-S 10 7034641 2 HOSE, 19 Hydraulic Parker #F4310637080808-19 11 7034667 2 HOSE, 22 Hydraulic Parker #F4310637080808-22 12 7100126 2 Pulley, Pump, Hydro Drive (5.00 O.D.) replaces 7078175 (4.50 O.D.) 13 7027199 2 KEY, M5 x M20 14 7091829 4 SET SCREW, 1/4-20 x 1/2 Socket Head w/ Patch Lock 15 7091627 2 WASHER, 1/4 x 1x 1/8 Flat 16 7090052 2 WASHER, 1/4 Split Lock 17 7091835 2 SCREW, M6 1.0 x 12mm Hex Head Cap 18 5023316 2 WHEEL MOTOR, Hydro Gear (HGM-12C-4005) Incl. Castle Nut & Woodruff Key (5/16 x 1 SAE J 502) 19 7091809 2 COTTER PIN, 1/8 x 1-1/4 20 7090544 8 SCREW,1/2-13 x 2-3/4 Hex Head Cap, GR 5 21 7091322 8 WASHER, 1/2 Split Lock 22 7091316 8 NUT, 1/2-13 Hex GR B 7074738 2 KIT, Fan Hub (Includes 1 each of 3 items shown below) (Hydro Gear p/n 7070632) for BDP-10A Pump w/thru Shaft HUB, Fan Mount WASHER, Belleville, Fan Mount NUT, Hex Nyloc Footnotes: MID-MOUNT SERIES 0 & 1 35 Manual No. 7006935
HYDRO RESERVOIR & FILTER ASSEMBLY Manual No. 7006935 MID-MOUNT 36 SERIES 0 & 1
HYDRO RESERVOIR & FILTER ASSEMBLY Item Part No Qty Description Note 1 7047141 1 ASSEMBLY, Hadraulic Tank Includes 4 items shown below 2 7074002 1 TANK, Hydraulic, NZM 3 7075289 1 CAP, Vented (Kelch # H4550D) 4 7075687 2 GROMMET (Dapco # 12078) 5 7011280 2 ELBOW FITTING (Dapco # 12784) 6 7015617 5 HOSE CLAMP 7 7090361 4 SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap 8 7090071 2 SCREW, 1/4-20 x 1/2 Hex Head Cap, GR 5 9 7090052 2 WASHER, 1/4 Split Lock 10 7041931 1 BRACKET, Filter 11 7090585 2 NUT, 5/16-18 Hex Flange Lock or 7091601 12 7034884 3 ELBOW FITTING, Hydraulic Parker #6 C50X-S 13 5023096 1 FILTER HEAD 14 1719168 1 FILTER 15 7034881 1 UNION TEE Parker #224-8 16 7034882 1 TEE FITTING, Hydraulic Parker #6 S50X-S 17 7035649 2 FITTING, Hydraulic Parker #6 V50X-S 18 7090548 2 SCREW, 1/4-20 x 1 Hex Head Cap, GR 5 or 7027230 19 7091294 4 WASHER, 1/4 Flat 20 7091603 2 NUT, 1/4-20 Hex Nyloc 21 7078077 1 BRACKET, Oil Tank 22 7034674 2 HOSE, 17-1/2 Hydraulic Parker R8010637060606-17.5 23 7034673 2 HOSE, 6 long Parker #R801NR39XX0606-6 24 7034706 1 * HOSE, 11.5 long Parker #R80137NR06XX06-11.5 25 7034703 1 * HOSE, 12 Long p/n 801-6-GRA-12 Footnotes: MID-MOUNT SERIES 0 & 1 37 Manual No. 7006935
ROLL BAR PROTECTIVE STRUCTURE Manual No. 7006935 MID-MOUNT 38 SERIES 0 & 1
ROLL BAR PROTECTIVE STRUCTURE Item Part No Qty Description Note 1 7400013 1 WELDMENT, LH Socket 2 7400012 1 WELDMENT, RH Socket 3 7100090 1 WELDMENT POST, LH 4 7100089 1 WELDMENT POST, RH 5 7100164 1 TOP LOOP, Folding, CZT 6 7100095 2 PIN, Hinge (ROPS) 7 7092123 6 SCREW, 1/2-13 x 3-1/4 Hex Head Cap, GR 5 8 7090975 11 NUT, 1/2-13 Hex Center Lock, GR 5 9 7100099 2 STAR KNOB (5/16-18 thread) 10 7091640 9 BOLT, 3/8-16 x 1 Square Neck Carriage, GR 5 11 7100228 1 SEAT BELT, w/metal Strap 12 7091585 1 NUT, 3/8-16 Hex Center Lock 13 7100227 1 RETRACTER, Seat Belt 14 7300139 1 BRACKET, Seat Belt, LH 15 7090646 5 SCREW, 1/2-13 x 1 Hex Head Cap, GR 5 16 7091299 8 NUT, 3/8-16 Hex Nyloc 17 7100284 1 * DECAL, ROPS Overhang 18 7100170 1 * DECAL, Caution ROPS 19 7100171 1 * DECAL, Caution ROPS (Spanish) 20 7100172 1 * DECAL, Warning ROPS 21 7100173 1 * DECAL, Warning ROPS (Spanish) Footnotes: NOTE: CZT Series 1 models equipped with Roll Bar Protective Structure. NOTE: * See Decal Page for pictoral representation. MID-MOUNT SERIES 0 & 1 39 Manual No. 7006935
48" CUTTING DECK ASSEMBLY (Sub Assy) Manual No. 7006935 MID-MOUNT 40 SERIES 0 & 1
48" CUTTING DECK ASSEMBLY (Sub Assy) Item Part No Qty Description Note 1 7072703 1 WELDMENT, 48 Deck 2 7092000 3 BOLT, 3/8-16 x 2-3/4 Square Neck Carriage, GR 5 3 7027327 1 WELDMENT, Pivot Pin 4 7091922 6 NUT, 1/2-13 Hex Light Nyloc 5 7091299 18 NUT, 3/8-16 Hex Nyloc 6 7091822 2 BOLT, 1/2-13 x 5 Hex Head 7 7029355 4 BOLT, 1/2-13 x 3-3/4 Hex Head Cap, GR 5 8 7091790 14 BOLT, 3/8-16 x 1-1/4 Square Neck Carriage, GR 5 9 7034934 3 PULLEY, 6 O.D. Idler p/n AM0516 10 7036456 2 SPACER, Gage Wheel 11 7091544 4 NUT, 1/2-13 Hex Flange Lock, GR 5 12 7046328 2 BRACKET, Rear Pusher Bar 13 7050490 1 WELDMENT, Spring Tensioner 14 7091304 1 SCREW, 3/8-16 x 1 Hex Head Cap, GR 5 15 7059107 2 ASSEMBLY, Pusher Bar 16 7072417 3 SPACER, Pulley 17 7029258 4 BUSHING - Suspension 18 7029263 2 SLEEVE - Suspension 19 7059108 1 WELDMENT, Pusher Bar 20 7073142 3 ROLLER Low Density Polyethylene or 7079226 21 7074789 1 WHEEL BRACKET Front Right 22 7074790 1 WHEEL BRACKET Front Left 23 7075580 1 BRACKET, Front Deck Lift, Right Hand 24 7075581 1 BRACKET, Front Deck Lift, Left Hand 25 7090258 4 NUT, 1/2-13 Hex, GR 5 or B 26 7090509 4 WASHER, 1/2 Internal Tooth Lock 27 7090250 2 WASHER, 1/2 Flat 28 7090517 3 WASHER, 3/8 Flat 29 7029264 2 GAGE WHEEL, Polyethylene 30 7090543 2 SCREW, 1/2-13 x 2 Hex Head Cap, GR 5 Footnotes: MID-MOUNT SERIES 0 & 1 41 Manual No. 7006935
48" CUTTING DECK ASSEMBLY (Final Assy) Manual No. 7006935 MID-MOUNT 42 SERIES 0 & 1
48" CUTTING DECK ASSEMBLY (Final Assy) Item Part No Qty Description Note 1 7011219 1 * BELT, HB Sect. 150.00 nom., HD Deck Belt 2 7072495 1 SWIVEL, 3/8 w/thru hole or 7024586 3 1723805 2 SLEEVE BUSHING, 3/4 I. D. GV3031224 4 7091901 1 BOLT, 3/8-16 x 4-1/2 Square Neck Carriage, GR 5 5 7091299 20 NUT, 3/8-16 Hex Nyloc 6 7029277 1 PIN, Chute Hinge 7 7091675 4 WASHER,.34 x 1.0 x.09 Flat 8 7091640 18 BOLT, 3/8-16 x 1 Square Neck Carriage, GR 5 9 7500080 1 * PULLEY, 6 O.D. Idler (assembly) includes pulley (7100073) & bushing (7100072); replaces 7034934 10 7034878 2 BELT GUARD 11 7043265 1 WELDMENT, 48 Discharge Chute 12 7053551 1 WELDMENT, Deck Idler Arm 13 7072719 3 ASSEMBLY, 48 Spindle components are shown on 48 spindle assembly page 14 7072986 1 SPRING, CVT Brake 15 7073129 1 IDLER BOSS 16 7078050 1 ROD, Tensioner (3/8-16 threads) 17 7300027 1 * BELT GUIDE replaces 7078229 18 7090130 3 NUT, 3/8-16 Hex, GR 5 or B 19 7090361 4 SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap 20 7091313 1 PIN, 3/32 x 1 Cotter 21 7091503 2 HAIR PIN, 3/32 x 1-1/2 22 7091557 1 * SCREW, 3/8-16 x 2-3/4 Hex Head Cap, GR 5 was 7091560 23 7090517 4 WASHER, 3/8 Flat 24 7027950 1 SPRING, Chute 25 7050513 1 ASSY, Discharge Chute used on CZT19481KWV model only 26 7050590 1 WELDMENT, 48 Chute 27 7078133 1 DEFLECTOR, Bottom 28 7091790 4 BOLT, 3/8-16 x 1-1/4 Square Neck Carriage, GR 5 29 7100621 1 CHUTE, Rubber 48 Footnotes: NOTE: * The Snapper part is number stamped on belt. NOTE: * 7600011, Pulley Replacement Kit includes one each of items 9, 17 & 22. MID-MOUNT SERIES 0 & 1 43 Manual No. 7006935
48" SPINDLE ASSEMBLY Manual No. 7006935 MID-MOUNT 44 SERIES 0 & 1
48" SPINDLE ASSEMBLY Item Part No Qty Description Note 1 7013370 1 WASHER for brg. Pre-seal kit 2 7016440 2 WASHER, Beveled 3 7076998 1 LUBE FITTING, 1/4-28 Thread Forming Was 29275, ALEMITE #3038-B 4 7029384 1 GREASE VENT, Spindle ALEMITE #321839 5 7029422 2 BALL BEARING 6 7034885 1 PULLEY, Driven 48 CZT 7 7045086 1 SHAFT, Spindle 8 7045092 1 WELDMENT, 48 Spindle 9 7063237 2 NUT, 5/8-11 Hex Flange Lock, GR 5 10 7063238 1 SEAL, Nylos 11 7074401 1 WASHER, Spindle 12 7075771 1 BLADE, 16-1/2 13 7091154 2 RETAINING RING, Internal TRUARC N5000-244 Footnotes: MID-MOUNT SERIES 0 & 1 45 Manual No. 7006935
DECALS Manual No. 7006935 MID-MOUNT 46 SERIES 0 & 1
DECALS Item Part No Qty Description Note 1 7074862 2 DECAL, SNAPPER PRO (2.6 high) used on CZT 1 7100246 1 DECAL, SNAPPER PRO (2.25 high) used on CZT 2 7071916 2 DECAL, SNAPPER (2.75 high) used on HZT 2 7100247 1 DECAL, SNAPPER (2.25 high) used on HZT 3 7075433 1 DECAL, Reservoir Oil Level 4 7073596 1 DECAL, Danger- High Speed Rotating Parts 5 7045108 1 DECAL, Tank Selector, MMZ 6 7100236 1 DECAL, Park Brake, Eng/Span 6 7078084 1 DECAL, Parking Brake similar to 7100236 (shown above) 7 7100170 1 DECAL, Caution ROPS 8 7100171 1 DECAL, Caution ROPS (Spanish) 9 7100235 1 DECAL, Control Panel, Engl/Span 9 7078055 1 DECAL, Control Panel similar to 7100235 (shown above) 10 7100843 2 DECAL, Warning (SP) 11 5100683 2 DECAL, Warning, Rollbar 12 7046720 1 DECAL, Chute/Deflector 13 7100284 1 DECAL, ROPS Overhang 14 7013010 1 DECAL, Danger, Cut Finger (CPSC) 15 7078182 1 DECAL, Detent 16 7075039 1 DECAL, Motion Control Levers 16 7100265 1 DECAL, Motion Control Levers (English) similar to 7075039 (shown above) 17 7100172 1 DECAL, Warning ROPS 18 7100173 1 DECAL, Warning ROPS (Spanish) 19 7035846 1 DECAL, Fuse 20 7073647 2 DECAL, Danger- Guard Catcher 21 7075565 1 DECAL, 48 Deck, Silver 22 7011248 1 DECAL, Belt & Blade Information 23 7027733 1 DECAL, Ear Protection Footnotes: MID-MOUNT SERIES 0 & 1 47 Manual No. 7006935
CONTROL PANEL ASSEMBLY Manual No. 7006935 MID-MOUNT 48 SERIES 0 & 1
CONTROL PANEL ASSEMBLY Item Part No Qty Description Note 1 7043390 1 DASH CONSOLE, Black 2 7074801 2 CONTROL LEVER, Throttle/Choke 3 7074804 1 CONTROL CABLE, Throttle (53.99" long) 4 7078143 1 CHOKE CABLE, Briggs, HZT (58.49" long) 4 7075046 1 CONTROL CABLE, Choke (Kawasaki)(53.49" long) 5 7091240 4 SCREW, #10-32 x 5/8 Hex Washer Self-Tap 6 7090376 4 NUT, #10-32 Hex Nyloc 7 7090361 4 SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap 8 7075086 1 TETHER STRAP also shown on Lift System Assembly Page 9 7091122 2 SCREW, 1/4-20 x 1/2 Hex Washer Self-Tap Was 90539 (also shown on Parking Brake Assembly Page) Footnotes: MID-MOUNT SERIES 0 & 1 49 Manual No. 7006935
ELECTRICAL COMPONENTS (except wiring) Manual No. 7006935 MID-MOUNT 50 SERIES 0 & 1
ELECTRICAL COMPONENTS (except wiring) Item Part No Qty Description Note 1 7072684 1 SWITCH, Ignition 2 7075622 1 SOLENOID, Super Trombetta (2 Terminal) vendor p/n 762-1221-210 3 7073406 1 KEY SET (2), G.C. Ignition not shown 4 7091122 2 SCREW, 1/4-20 x 1/2 Hex Washer Self-Tap Was 90539 5 1716368 1 ASSEMBLY, Seat Switch (NC) also shown on Seat Assembly pages 6 7091603 3 NUT, 1/4-20 Hex Nyloc 7 1960536 2 SCREW seat switch mount screws 8 7075132 1 SWITCH, PTO, Yellow 9 7074796 1 HOUR METER w/flash Alerts Sendec Corp. Model No. 804-204 10 7075911 1 BATTERY, 11 Plate 375CCA- Wet 11 7090072 2 SCREW, 1/4-20 x 5/8 Hex Head Cap, GR 5 12 7091294 2 WASHER, 1/4 Flat 13 7090372 2 NUT, 1/4-20 Hex Center Lock 14 7078086 1 BRACKET, Battery 15 7091240 2 SCREW, #10-32 x 5/8 Hex Washer Self-Tap 16 7090376 2 NUT, #10-32 Hex Nyloc 17 7012080 12 CABLE TIE, 7 not shown 18 7015861 1 CLIP, Harness 19 7023355 3 SWITCH- DPDT (NC/NO) also shown on Twin Stick Control and Parking Brake pages 20 7090361 8 SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap 21 7090913 6 SCREW, #10-24 x 1/2 Hex Washer Self-Tap (Torx) Footnotes: MID-MOUNT SERIES 0 & 1 51 Manual No. 7006935
WIRING HARNESS (Briggs Engines) Manual No. 7006935 MID-MOUNT 52 SERIES 0 & 1
WIRING HARNESS (Briggs Engines) Item Part No Qty Description Note 1 7078157 1 WIRE HARNESS, 21 HP Briggs 2 7075038 1 CABLE, Battery- Positive (6 Gage, 34 long) not shown 3 7035609 1 CABLE, Battery- Ground (6 Gage/14 Gage, 23 long) not shown 4 7075602 1 CABLE, Solenoid to Starter (6 Gage, 10 long) not shown 5 7075091 1 WIRE, Solenoid- Ground (10 Gage, 6-1/2 long) not shown Footnotes: MID-MOUNT SERIES 0 & 1 53 Manual No. 7006935
WIRING HARNESS (Kawasaki Engines) Manual No. 7006935 MID-MOUNT 54 SERIES 0 & 1
WIRING HARNESS (Kawasaki Engines) Item Part No Qty Description Note 1 7078156 1 WIRE HARNESS, 19 HP Kawasaki 2 7075038 1 CABLE, Battery- Positive (6 Gage, 34 long) not shown 3 7035609 1 CABLE, Battery- Ground (6 Gage/14 Gage, 23 long) not shown 4 7075602 1 CABLE, Solenoid to Starter (6 Gage, 10 long) not shown 5 7075091 1 WIRE, Solenoid- Ground (10 Gage, 6-1/2 long) not shown Footnotes: MID-MOUNT SERIES 0 & 1 55 Manual No. 7006935
WIRING SCHEMATIC (Briggs) Manual No. 7006935 MID-MOUNT 56 SERIES 0 & 1
WIRING SCHEMATIC (Briggs) Item Part No Qty Description Note 1 7078157 1 WIRE HARNESS, 21 HP Briggs Footnotes: MID-MOUNT SERIES 0 & 1 57 Manual No. 7006935
WIRING SCHEMATIC (Kawasaki) Manual No. 7006935 MID-MOUNT 58 SERIES 0 & 1
WIRING SCHEMATIC (Kawasaki) Item Part No Qty Description Note 1 7078156 1 WIRE HARNESS, 19 HP Kawasaki Footnotes: MID-MOUNT SERIES 0 & 1 59 Manual No. 7006935
Parts Manual for MID-MOUNT ZERO TURNING HYDRO DRIVE SERIES 0 & 1 IT IS THE POLICY OF BRIGGS & STRATTON CORP TO IMPROVE ITS PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS McDonough, GA, 30253 U.S.A. Briggs & Startton Yard Power Products Group Copyright 2007 Briggs & Startton Corporation Milwaukee, WI USA. All Rights Reserved Revision 3, 4/26/2007 Manual No. 7006935