Technical data sheet R3..xx-S.. Characterised control valves, 3-way, with internal thread For closed cold and warm water systems For modulating water-side control of HU and heating systems ir bubble-tight (control path - ) Overview of types Type R30-P5-S R30-P4-S R30-P63-S R30--S R30-P6-S R30-P5-S R30-4-S R300-4-S R300-6P3-S R305-6P3-S R305-0-S R303-6-S3 R3040-6-S3 R3040-5-S4 R30-5-S4 R30-40-S4 R30-58-S4 www.syxthsense.com kvs [m³/h] DN ["] ps [kpa] n(gl) Sv min. 0.5 0.4 0.63.6.5 4 4 6.3 6.3 0 6 6 5 5 40 58 0 0 5 5 3 40 40 3/4 3/4 /4
R3..xx-S.. Technical data Functional data Media Cold and hot water, water with glycol up to max. % vol. Medium temperature -0 C... 0 C Medium temperature note The allowed media temperature can be limited, depending on the type of actuator. The correct values can be found in the respective actuator sheets. Closing pressure ps 400 kpa Differential pressure pmax 3 kpa Differential pressure note (00 kpa for low-noise operation) Flow characteristic Control path : equal percentage (in accordance with VDI/VDE 78) Leakage rate Control path, ir bubble-tight (EN 66-) Leakage class ypass Leakage Class I (DIN EN 349 and DIN EN 60534-4)... % of kvs, in relation to the highest value within the DN Pipe connectors Internal thread in accordance with ISO 7/ ngle of rotation with limitation 90 (operating range control path... 90, bypass... 70 ) Installation position Upright to horizontal (in relation to the spindle) Maintenance Maintenance-free Materials Valve Forged, nickel-plated brass body Valve cone Stainless steel Spindle Stainless steel Stem seal O-ring EPDM Valve seat PTFE, O-Ring EPDM (DN0 Viton) Characterising disk Path -: DN... DN TEFZEL (R3040-5-S4, R30-40-S4, R30-58-S4: Stainless Steel) Safety notes! The ball valve has been designed for use in stationary heating, ventilation and air-conditioning systems and is not allowed to be used outside the specified field of application, especially in aircraft or in any other airborne means of transport. Only authorised specialists may carry out installation. ll applicable legal or institutional installation regulations must be complied with during installation. The ball valve does not contain any parts that can be replaced or repaired by the user. The ball valve may not be disposed of as household refuse. ll locally valid regulations and requirements must be observed. When determining the flow rate characteristic of controlled devices, the recognised directives must be observed. Product features Principle of operation Flow characteristic The characterised control valve is adjusted by a rotary actuator. The actuator is controlled by a commercially available modulating or 3-point control system and moves the ball of the valve the throttling device to the position dictated by the positioning signal. Open the characterised control valve counterclockwise and close it clockwise. Equal percentage flow control is ensured by the integrated characterising disk.
R3..xx-S.. Installation instructions Recommended installation positions The ball valve can be installed upright to horizontal. The ball valve may not be installed in a hanging position, i.e. with the spindle pointing downwards. 90 90 Water quality requirements Maintenance Flow direction The water quality requirements specified in VDI 035 must be adhered to. Characterised control valves are regulating devices. The use of dirt filters is recommended in order to prolong their service life as modulating instruments. all valves and rotary actuators are maintenance-free. efore any kind of service work is carried out on the actuator, it is essential to isolate the rotary actuator from the power supply (by unplugging the electrical cable). ny pumps in the part of the piping system concerned must also be switched off and the appropriate slide valves closed (allow everything to cool down first if necessary and reduce the system pressure to ambient pressure level). The system must not be returned to service until the characterised control valve and the rotary actuator have been properly reassembled in accordance with the instructions and the pipeline has been refilled in the proper manner. The direction of flow, specified by an arrow on the housing, is to be complied with, since otherwise the ball valve could become damaged. Please ensure that the ball is in the correct position (marking on the spindle). = % = 0% ccessories Description Mechanical accessories Pipe connector for characterised control valve DN Pipe connector for characterised control valve DN 0 Pipe connector for characterised control valve DN 5 Pipe connector for characterised control valve DN 3 Pipe connector for characterised control valve DN 40 Pipe connector for characterised control valve DN Data sheet name ZR3 ZR30 ZR35 ZR33 ZR340 ZR3 3
R3..xx-S.. Dimensions / Weight Dimensional drawings min. Y min. X H 3) 4 L M DN Type Weight approx. [kg] ["] L L H M X Y R30-P5-S 0.7 67 3 35 36 30 90 R30-P4-S 0.7 67 3 35 36 30 90 R30-P63-S 0.7 67 3 35 36 30 90 R30--S 0.7 67 3 35 36 30 90 R30-P6-S 0.37 67 3 44 36 30 90 R30-P5-S 0.37 67 3 44 36 30 90 R30-4-S 0.37 67 3 44 36 30 90 0 R300-4-S 0.46 3/4 78 4 46 4.5 0 90 0 R300-6P3-S 0.46 3/4 78 4 46 4.5 0 90 5 R305-6P3-S 0.65 87 6 46 45 35 90 5 R305-0-S 0.65 87 6 46 45 35 90 3 R303-6-S3 0.95 /4 05 9.5 55.5 40 90 40 R3040-6-S3. 9.5 56 40 90 40 R3040-5-S4. 9 6 66.5 90 R30-5-S4.9 5 56 68 45 90 R30-40-S4.8 4 68 79 6 90 R30-58-S4.8 4 68 79 6 90 L: Maximum screwing depth. X/Y: Minimum distance with respect to the valve centre. The actuator dimensions can be found on the respective actuator data sheet. Further documentation Complete overview «The complete product range of water solutions» Data sheets actuators Installation instructions for actuators and/or ball valves, respectively Notes for project planning (hydraulic characteristic curves and hydronic circuits, installation instructions, commissioning, maintenance, etc.) 4
R..-S.. Y R3..-S.. H X 770-0000. L M L t p s 0... +0 C kpa DN mm 80 C C 0 C C 0 C KR.. TR.. LR.. NR.. SR.. TRF.. LRF.. NRF.. SRF.. mm L H M L X Y X Y X Y X Y X Y X Y X Y X Y X Y R0..-S R30..-S ¹/₂ 67 44 36 3 75 85 75 95 75 30 80 30 80 90 80 00 90 0 90 0 90 R00..-S R300..-S 0 ³/₄ 78 46 4.5 4 00 75 35 80 35 80 05 90 5 90 5 90 R05..-S R305..-S 5 87 46 45 6 00 75 35 80 35 80 05 90 5 90 5 90 R03..-S3 R303..-S3 3 ¹/₄ 05.5 55.5 9 40 80 40 80 30 90 30 90 R040..-S3 R3040..-S3 40 ¹/₂.5 56 9 40 80 40 80 30 90 30 90 R3040-5-S4 40 ¹/₂ 6 66.5 9 80 40 90 R0..-S4 R30..-S4 5 56 68 45 80 35 90 R30-40-S4 R30-58-S4 4 68 79 6 80 5 90
k v Y M4 % 0% p vmax <3 kpa M4 % 0% 0% % k v Y % 0% p vmax <0 kpa % 0% 0% % 90 90 % 0% 0% %