7 R Rotary Mower 9-5 PART'S MANUAL An Operator's Manual was shipped with the equipment in the Manual Canister. This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator's Manual is not with the equipment, contact your dealer or Servis-Rhino (800-6-558) to obtain a Free copy before operating the equipment. Quick Hitch Standard RHINO 00 S. Sangamon Ave. Gibson City, IL 60936 800-6-558 Email: parts@servis-rhino.com 00 Alamo Group Inc.
TO THE OWNER/OPERATOR/DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. BEFORE YOU START!! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense! WARRANTY INFORMATION: Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic failure with possible injury or death.
PARTS SECTION
PARTS ORDERING GUIDE RHINO 00 S. Sangamon Ave. Gibson City, IL 60936 800-6-558 Email: parts@servis-rhino.com 00 Alamo Group Inc. Parts Section
PART NAME INDEX A-FRAME QUICK HITCH ASSEMBLY... A-FRAME QUICK HITCH ATTACHMENT... 5 A-FRAME STANDARD ASSEMBLY... 6 A-FRAME STANDARD ATTACHMENT... 7 BLADE PAN ASSEMBLY... 8 CASTER FORK WHEEL ASSEMBLY... 0 CHAINGAURD ASSEMBLY - FRONT... CHAINGAURD ASSEMBLY - REAR... DEFLECTOR ASSEMBLY - FRONT... 3 DEFLECTOR ASSEMBLY - REAR... DRIVELINE ASSEMBLY - (SLIPCLUTCH)... 5 DRIVELINE ASSEMBLY - S/N 0000-6385... 6 DRIVELINE ASSEMBLY - S/N 6386-CURRENT... 8 GEARBOX ASSEMBLY - S/N 0,000-5535... 9 GEARBOX ASSEMBLY - S/N 5537-6385... GEARBOX ASSEMBLY - S/N 6386-9000... 3 GEARBOX ASSEMBLY - S/N 8600-9999... 5 GEARBOX ASSEMBLY - S/N 30,000-CURRENT... 7 GEARBOX ATTACHMENT - S/N 0,000-5535... 9 GEARBOX ATTACHMENT - S/N 5537 - CURRENT... 30 SLIPCLUTCH... 3 TAILWHEEL ASSEMBLY... 3 TAILWHEEL HUB ASSEMBLY... 33 7 00 Alamo Group Inc. Parts Section -3
A-FRAME QUICK HITCH ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 00780550 FLAT, REAR BRACE 00780563 FLAT, A-FRAME 3 00780603 BAR, BRACE 00009500 BOLT-HEX 3/ NC -/ PL5 5 0758550030 SPACER 6 0003700 NUT TOPLOCK 7 905 CARB 5/8- NC 8 530 BUSHING, ORDER 780 MIN HT 9 00756077 WASHER,5/8 HARDENED 0 0069500 NUT,TOPLOCK 5/8 NC PLB 0070300 HEXB 0078059 BUSHING, A-FRAME TOGGLE 3 085500 HEXB 3/ NC PLC PL5 5/8- UNC -3/ PL 5/8 NC PL5 7 00 Alamo Group Inc. Parts Section -
A-FRAME QUICK HITCH ATTACHMENT ITEM PART NO. QTY. DESCRIPTION 007753 PIN WRIST CAT & 96 CLIP (LYNCH PIN), 3/3 DIA. 3 00780663 FLAT, DRIVELINE STORAGE 0000800 LOCKNUT TLM 5 007883 HHCS /-3UNC -/ PL5 6 085500 HEXB 7 00756077 WASHER,5/8 HARDENED 8 0078508 BUSHING, OD X /6 IDX.57WA 9 0730000 BUSHING 0 0069500 NUT,TOPLOCK 5/8 NC PLB 0078538 BUSHING,CAT. II QUICK HITCH / 5/8 NC NC PLB PL5 7 00 Alamo Group Inc. Parts Section -5
A-FRAME STANDARD ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 0078087 FLAT, REAR BRACE 0078087 FLAT, A-FRAME 3 0075799 BAR TOP LINK BD80 00757953 BUSHING -/X7/3X3 A-FRAME 5 0078598 HEXB 3/-0UNC 5-/ 6 0003700 NUT TOPLOCK PL5 3/ NC PLC 7 00 Alamo Group Inc. Parts Section -6
A-FRAME STANDARD ATTACHMENT ITEM PART NO. QTY. DESCRIPTION 007753 PIN WRIST CAT & 96 CLIP (LYNCH PIN), 3/3 DIA. 3 085500 HEXB 0069500 NUT,TOPLOCK 5/8 NC PLB 5 3707B PIN TOP LINK CAT (PLATED) 6 3707B3 CLIP-X HAIR PIN 7 00780663 FLAT, DRIVELINE STORAGE 8 0000800 LOCKNUT TLM 9 007883 HHCS /-3UNC -/ PL5 5/8 NC / PL5 NC PLB 7 00 Alamo Group Inc. Parts Section -7
BLADE PAN ASSEMBLY 7 00 Alamo Group Inc. Parts Section -8
BLADE PAN ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION 00785567 BLADE, FAN CCW, 5-/ CTR-TIP 0078656 WELDMENT, BLADE PAN 7 - S/N 30,000-CURRENT & 5537-8600 0078877 WELDMENT, BLADE PAN 7 - S/N 8600-9999 0078 WELDMENT, BLADE PAN 7 - S/N 0000-5535 3 007506 NUT TOPLOCK 7/8 NF PLC 0076535 WASHER-7/8 STR PLAIN 5 007830 BLADE BOLT 7/8 DIA X 3 LG 7 00 Alamo Group Inc. Parts Section -9
CASTER FORK WHEEL ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 00776 FORK CASTER ASSEMBLY 00036900 PIN-COTTER / X -/ 3 5B000 WASHER SAE / PLATED 007767 WASHER FLAT 06 X 0 X FLAT 5 00776 NUT SPINDLE M X 6 007760 PIN,COTTER 5/3X-/ PL 7 00776 BOLT SPINDLE M X X 86 8 007766 BOLT M X.5 X 5 9 00759635 FLATWASHER / HRDED NONPLTD 0 0078038 ASSY, TAILWHEEL HUB 08500 FLATWASHER PL STD 3730H TIRE & WHEEL ASSEMBLY 7 00 Alamo Group Inc. Parts Section -0
CHAINGAURD ASSEMBLY - FRONT ITEM PART NO. QTY. DESCRIPTION 00785 - CHAINGUARD ASSEMBLY FRONT 0030700 9 HHCS /-3UNC -/ PL5 0000700 9 FLATWASHER 3 0000800 9 LOCKNUT TLM / PL STD / NC PLB 7 00 Alamo Group Inc. Parts Section -
CHAINGAURD ASSEMBLY - REAR ITEM PART NO. QTY. DESCRIPTION 007853 - CHAINGUARD ASSEMBLY REAR 007883 9 HHCS /-3UNC -/ PL5 0000700 9 FLATWASHER 3 0000800 9 LOCKNUT TLM / PL STD / NC PLB 7 00 Alamo Group Inc. Parts Section -
DEFLECTOR ASSEMBLY - FRONT ITEM PART NO. QTY. DESCRIPTION 00780656 FRONT RUBBER DEFLECTOR 0030700 9 HHCS /-3UNC -/ PL5 3 0000700 9 FLATWASHER 0000800 9 LOCKNUT TLM / PL STD / NC PLB 7 00 Alamo Group Inc. Parts Section -3
DEFLECTOR ASSEMBLY - REAR ITEM PART NO. QTY. DESCRIPTION 00785 REAR RUBBER DEFLECTOR 007835 REAR DEFLECTOR STRAP 3 007883 9 HHCS /-3UNC -/ PL5 0000700 9 FLATWASHER 5 0000800 9 LOCKNUT TLM / PL STD / NC PLB 7 00 Alamo Group Inc. Parts Section -
DRIVELINE ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 007687B DRIVELINE, SP 0076500A ASY,YOKE COLLAR - COMPLETE 007563 CROSS & BEARING KIT SERIES 0 3 0075969 PIN ROLL 8MM X 60MM 0075965 PIN ROLL INNER TUBE 5 0077739A YOKE, -3/8 BORE SP 6 0076506 COLLAR-INNER-GUARD-RETAINER 7 0075330 6 BOLT, NYLON - SAFETY SHIELD] 8 0076507 COLLAR-OUTER-GUARD-RETAINER 9 0077079 KIT,SLIDE COLLAR REPAIR 0 0077953 COMPLETE SHIELD KIT 7 00 Alamo Group Inc. Parts Section -5
DRIVELINE ASSEMBLY - S/N 0000-6385 7 00 Alamo Group Inc. Parts Section -6
DRIVELINE ASSEMBLY - S/N 0000-6385 ITEM PART NO. QTY. DESCRIPTION 0076868B DRIVELINE, SC 0076500A ASY,YOKE COLLAR - COMPLETE 007563 CROSS & BEARING KIT SERIES 0 3 0075969 PIN ROLL 8MM X 60MM 0075965 PIN ROLL INNER TUBE 5 00773087 CLUTCH -3/8 BORE, SERIES 0 6 0076506 COLLAR-INNER-GUARD-RETAINER 7 0075330 6 BOLT, NYLON - SAFETY SHIELD] 8 0076507 COLLAR-OUTER-GUARD-RETAINER 9 0077079 KIT,SLIDE COLLAR REPAIR 0 0077953 COMPLETE SHIELD KIT 0075968 YOKE, OUTER TUBE 0076895 YOKE, INNER TUBE 7 0075303 SPRING 7 00773080 FLANGED YOKE 73 0077308 BUSH 7 00773085 LINING RING 75 0077308 SPECIAL HUB F0 76 00773083 PRESSURE PLATE 77 007536 8 BOLT AND NUT M0 X 80 7 00 Alamo Group Inc. Parts Section -7
DRIVELINE ASSEMBLY - S/N 6386-CURRENT ITEM PART NO. QTY. DESCRIPTION 00786899 0076500A 007563 30 0078773 3 0076506 33 0075330 6 37 0076507 0 007877 7 0075303 8 7 0078775 73 0077308 7 0076837 75 0075903 76 007537 77 0076836 78 007536 8 00 0077079 COMPLETE DRIVELINE COMPLETE COLLAR YOKE C CROSS JOURNAL SET FRICTION CLUTCH GUARD RETAINING COLLAR FOR OUTER TUBE BOLT GUARD RETAINING COLLAR FOR INNER TUBE COMPLETE GUARD WITH INSTRUCTION MANUAL SPRING FLANGED YOKE BUSH LINING RING BOLT & NUT MX65 HUB F PRESSURE PLATE BOLT & NUT M0X80 KIT COLLAR FOR YOKES 3/8" 7 00 Alamo Group Inc. Parts Section -8
PAGE LEFT BLANK INTENTIONALLY
GEARBOX ASSEMBLY - S/N 0,000-5535 7 00 Alamo Group Inc. Parts Section -9
GEARBOX ASSEMBLY - S/N 0,000-5535 Continued... ITEM PART NO. QTY. DESCRIPTION 0078065 - GEARBOX 007873 HOUSING 00775859 CAP,INPUT 3 0056600 INPUT GEAR 00563700 BEARING, BALL 5 005600 OIL SEAL 6 00775860 SHAFT,INPUT 7 005600 3 RING, RETAINING 8 007875 GEAR SPACER 9 0078098 - INPUT GASKET (0.30) 0 0078097 - INPUT GASKET (0.3) 0076099 - GASKET,OUTPUT (0.30) 0076098 - GASKET,OUTPUT CAP (0.3) 3 0075595 0 LOCKWASHER M0 6368C8 0 M0X.5X5 GR.8.8-FT HEX CAPSC 5 0075869 NUT,- FLANGED HEX SLOTTED 6 00606000 PIN-COTTER 3/6 X 7 00563500 SEAL, OIL OUTPUT 8 00757683 CAP, OUTPUT 9 007596 BEARING 3008 0 007876 OUTPUT BEARING SPACER 007878 5 TOOTH OUTPUT SHAFT & PINION 00758739 - SHIM,GEAR ADJUSTMENT.500 3 00758738 - SHIM,PINION ADJUSTMENT 0.30 0075867 - SHIM,0. STEEL GEAR BACKLASH 5 0056800 BEARING,BALL 6 007693 WASHER,SEALING,7.8MXMX3M 7 00770737 LEVEL PLUG M8 X.5 8 007839 SEAL PROTECTOR 9 79 SNAP RING -/ OD X -5/6 ID 30 0076 PLUG,VENT W/WASHER 8M-P.5 7 00 Alamo Group Inc. Parts Section -0
GEARBOX ASSEMBLY - S/N 5537-6385 7 00 Alamo Group Inc. Parts Section -
GEARBOX ASSEMBLY - S/N 5537-6385 Continued... ITEM PART NO. QTY. DESCRIPTION 007857 ASY,GEARBOX (GIF) - (LF-0J) 50 RPM,NON-LUBED,:.7 RATIO 0078686 KIT,BEVEL GEAR - TWO GEARS 3 0078687 KIT,ROLLER BEARING 0078688 KIT,SEAL & SHIM 5 007868 SHAFT,INPUT - -3/8" SMOOTH 8 0078689 NUT,CASTLE M0 X.0 0 007786 WASHER,FLAT - 5 X X 0075777 NUT,CASTLE M X.0 007869 WASHER,FLAT - X 37 X 3 7 0078685 SHAFT,OUTPUT - D.P. 8/6 Z 3 7087 COTTER PIN - X 0 5 636C8 HEXB M0 X 6 PL8 6 00755633 3 PLUG,SOLID GAS - 3/8" 7 7659 PLUG,BREATHER GAS - 3/8" 8 7097 COTTER PIN - 5 X 50 7 00 Alamo Group Inc. Parts Section -
GEARBOX ASSEMBLY - S/N 6386-9000 7 00 Alamo Group Inc. Parts Section -3
GEARBOX ASSEMBLY - S/N 6386-9000 Continued... ITEM PART NO. QTY. DESCRIPTION 0078678 ASY,GEARBOX (GIF) - (LF-0J) 50 RPM,NON-LUBED,:.7 RATIO 0078686 KIT,BEVEL GEAR - TWO GEARS 3 0078687 KIT,ROLLER BEARING 0078688 KIT,SEAL & SHIM 5 0078688 SHAFT,INPUT - -3/8-6 SPINE 8 0078689 NUT,CASTLE M0 X.0 0 007786 WASHER,FLAT - 5 X X 0075777 NUT,CASTLE M X.0 007869 WASHER,FLAT - X 37 X 3 7 0078685 SHAFT,OUTPUT - D.P. 8/6 Z 3 7087 COTTER PIN - X 0 5 636C8 HEXB M0 X 6 PL8 6 00755633 3 PLUG,SOLID GAS - 3/8" 7 7659 PLUG,BREATHER GAS - 3/8" 8 7097 COTTER PIN - 5 X 50 7 00 Alamo Group Inc. Parts Section -
GEARBOX ASSEMBLY - S/N 8600-9999 7 00 Alamo Group Inc. Parts Section -5
GEARBOX ASSEMBLY - S/N 8600-9999 Continued... ITEM PART NO. QTY. DESCRIPTION 007905 ASY, HD0 GEARBOX-:.7 NO-LUBE GEAR ADJ TO INPUT SHAFT 007907 CAP, INPUT SHAFT 3 007908 SHAFT, INPUT SHAFT - 6 SPLINE 0056800 BEARING, BALL (35 X 7 X 7) 607 5 00563700 BEARING, BALL (0 X 80 X 8) 6 00790986 KIT, GEAR/OUTPUTSHAFT 8,9,0 00790969 KIT, HD0 GEAR SHIM 00790980 SPACER, INPUT SHAFT 00790979 RING, RETAINING 3 007905 CAP, OUTPUT SHAFT 00790973 SEAL, OIL 5 X 3.95 X 0 5 007596 BEARING, TAPERED ROLLER 3008 7 0079097 SEAL, OIL 5 X 39.7 X 9.5 8 0079098 NUT, M-.0 SLOTTED FLANGE 9 00606000 PIN, COTTER 3/6 X " 0 0079098 SPACER, OUTPUT SHAFT 00790975 GASKET, INPUT CAP -.3 MM 00790976 GASKET, INPUT CAP -.30 MM 3 00790977 GASKET, OUTPUT CAP -.3 MM 00790978 GASKET, OUTPUT CAP -.30 MM 5 00790983 WASHER, SEALING M6 6 0079098 PLUG, LEVEL M6 X.5 7 00790985 PLUG, VENT M6 X.5 8 303 PLUG, SOCKET HEAD /"-8 NPT 9 0000 0 LOCKWASHER, 3/8 PL 3 00790997 RING, RETAINING-SW-0MM 30 00000 0 HHCS, 3/8"-6 X " PL5 33 007909 SPACER, HD0 OUTPUT 7 00 Alamo Group Inc. Parts Section -6
GEARBOX ASSEMBLY - S/N 30,000-CURRENT 7 00 Alamo Group Inc. Parts Section -7
GEARBOX ASSEMBLY - S/N 30,000-CURRENT Continued... ITEM PART NO. QTY. DESCRIPTION 0 007907 - ASSY, GEARBOX- :.7 ADJ TO INPUT SHAFT 007909 HOUSING, GEARBOX 0079030 CAP, HOUSING 3 007903 SHAFT, INPUT--3/8 6-SPL 0075753 SEAL, OIL - 35 X 7 X 0 5 7650 CAP, OIL-7 X 0 6 636C8 HHCS, M0-.5 X 6MM PL8 7 007903 PLUG, SAE ORING -6MB 8 0079033 SHAFT, OUTPUT 9 0075777 NUT, CASTLE M-.0 0 007786 WASHER, FLAT - 5 X X 007903 KIT, INPUT SHIM 0079035 KIT, OUTPUT SHIM 3 007909 KIT, GEAR- :.7 0056800 BEARING, BALL 607 (35X7X7) 5 7653 RING, SNAP -7 X 75 X.5 6 0075757 BEARING, ROLLER 3007 (35X7X8.5) 7 007905 NUT, CASTLE M0 X.5 8 00766 BEARING, ROLLER 30306 (30X7X0.75) 9 76658 BEARING, ROLLER 3008 (0X80X9.75) 0 00753 RING, SNAP DIN7-80 X.5 0075783 SEAL, OIL -0 X 80 X 0075773 SHIELD, PROTECTIVE - 0. X 79.9 X 3 7087 PIN, COTTER M X 0 7097 PIN, COTTER M5 X 50 5 00790985 PLUG, VENT M6-.5 6 00790983 SEALING WASHER 7 038609 DIPSTICK, OIL- EZ0 7 00 Alamo Group Inc. Parts Section -8
GEARBOX ATTACHMENT - S/N 0,000-5535 ITEM PART NO. QTY. DESCRIPTION 007798 SHIELD WELDMENT 0078087 WELDMENT, SHIELD BRACKET 3 5F830 / NC WING NUT 0003500 FLATWASHER,5/6,TYPE AW,ZP 5 095878 BOLT METRIC 8-P.5-0MM PL5 6 00756077 WASHER,5/8 HARDENED 7 085500 3 HEXB 8 7A83 HHCS /NC X 3 PL MUST BE GR FOR SHER BOLT 0075303 HHCS / NC 3 PL8 MUST BE GR8 FOR SLIPCLUTCH 0 0069500 NUT,TOPLOCK 5/8 NC PLB 9 0000800 LOCKNUT TLM 0000700 FLATWASHER 0076 PLUG,VENT W/WASHER 8M-P.5 5/8 NC / PL5 NC PLB / PL STD 7 00 Alamo Group Inc. Parts Section -9
GEARBOX ATTACHMENT - S/N 5537 - CURRENT ITEM PART NO. QTY. DESCRIPTION 00785575 SHIELD, GEARBOX 0078557 SUPPORT RING, GEARBOX SHIELD 3 0003500 FLATWASHER,5/6,TYPE AW,ZP 095878 BOLT METRIC 8-P.5-0MM PL5 5 085500 HEXB 5/8 NC PL5 6 00756077 WASHER,5/8 HARDENED 7 0069500 NUT,TOPLOCK 5/8 NC PLB 8 7659 PLUG,VENT 3/8" 9 7A83 HHCS /NC X 3 PL MUST BE GR FOR SHER BOLT 0075303 HHCS / NC 3 PL8 MUST BE GR8 FOR SLIPCLUTCH 0 0000800 LOCKNUT TLM / NC PLB 7 00 Alamo Group Inc. Parts Section -30
SLIPCLUTCH ITEM PART NO. QTY. DESCRIPTION 00773087 - CLUTCH -3/8 BORE, SERIES 0 00773080 YOKE FLANGED FOR 00773087 CLU CLUTCH 007893 SUPPORT W/-3/8 BORE (W/3MM HOLE) 3 0077308 BUSHING FOR 00773087 CLUTCH 00773083 PRESSURE PLATE FOR 00773087 5 00773085 LINING CLUTCH SERIES 0 6 0075303 8 SPRING FOR 00773087 CLUTCH 7 007536 8 NUT & BOLT M0X80 8 0077308 NUT & BOLT M0X65 7 00 Alamo Group Inc. Parts Section -3
TAILWHEEL ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 0078068 WELDMENT, T/W BEAM 60 007760 AG SE CASTER FORK WHEEL ASSY 3 0076375 HHCS /NC X 3-/ PL5 0000800 LOCKNUT TLM 5 085700 HHCS 6 0069500 NUT,TOPLOCK 5/8 NC PLB / 5/8 NC NC PLB PL5 7 00 Alamo Group Inc. Parts Section -3
TAILWHEEL HUB ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 0078038 - ASSY, TAILWHEEL HUB 00776 HUB BOLT 007708 NIPPLE, GREASE M8X 007763 BEARING 3 00759635 FLATWASHER / HARDND NONPLATD 00766 HEXB METRIC -P.75-5MM PL5 5 007707 BUSHING SPINDLE STEP 6 007708 DUST CAP 7 007769 SEAL OIL 0 X 6 X 8 7 00 Alamo Group Inc. Parts Section -33
LIMITED WARRANTY. LIMITED WARRANTIES.0.Servis-Rhino warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser ( Purchaser ) and warrants for six months to the original commercial or industrial purchaser ( Purchaser ) that the goods purchased are free from defects in material or workmanship..0.manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship..03.this limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal combustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically found in your Operator s Manual..0.Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any nature on behalf of Manufacturer.. REMEDIES AND PROCEDURES..0.This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer within 30 days of purchase..0.purchaser claims must be made in writing to the Authorized Dealer ( Dealer ) from whom Purchaser purchased the goods or an approved Authorized Dealer ( Dealer ) within 30 days after Purchaser learns of the facts on which the claim is based..03.purchaser is responsible for returning the goods in question to the Dealer..0.If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and service due to defects in material or workmanship, Manufacturer will: (a) (b) Repair or replace the defective goods or part(s) or Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer) if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty by Manufacturer. The choice of remedy shall belong to Manufacturer..05.Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s) from the Dealer to the designated factory. 3. LIMITATION OF LIABILITY. 3.0.MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. 3.0.MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR USE OF THE GOODS. 3.03.EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOT LIMITED TO, ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROM THE USE OR OPERATION OF THE GOODS OR ANY BREACH OF THIS WARRANTY. NOT WITHSTANDING THE ABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER S LIABILITY HEREUNDER FOR DAMAGES INCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE GOODS. 3.0.NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER THIS WARRANTY MAY BE BROUGHT MORE THAN TWO () YEARS AFTER THE CAUSE OF ACTION HAS OCCURRED.. MISCELLANEOUS..0.Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County, Texas..0.Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a waiver of any other term..03.if any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such provision shall not invalidate any other provisions herein..0.applicable law may provide rights and benefits to purchaser in addition to those provided herein. KEEP FOR YOUR RECORDS SERVIS-RHINO ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine identification when applying for warranty. Servis-Rhino Implement Model Serial Number Date Purchased Dealer ATTENTION: READ YOUR OPERATOR'S MANUAL RHINO 00 S. Sangamon Ave. Gibson City, IL 60936 800-6-558 Email: parts@servis-rhino.com R
TO THE OWNER/OPERATOR/DEALER R To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the information you need. The OCCUPATIONAL SAFETY AND HEALTH ACT (98.5 Subpart C) makes these minimum safety requirements of tractor operators: REQUIRED OF THE OWNER:. Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and. Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE JC; and 3. Ensure that each employee uses such Seatbelt while the tractor is moving; and. Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the protected area provided by the ROPS. REQUIRED OF THE OPERATOR. Securely fasten seatbelt if the tractor has a ROPS.. Where possible, avoid operating the tractor near ditches, embankments, and holes. 3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces.. Stay off slopes too steep for safe operation. 5. Watch where you are going - especially at row ends, on roads, and around trees. 6. Do not permit others to ride. 7. Operate the tractor smoothly - no jerky turns, starts, or stops. 8. Hitch only to the drawbar and hitch points recommended by the tractor manufacturer. 9. When the tractor is stopped, set brakes securely and use park lock, if available. Keep children away from danger all day, every day... Equip tractors with rollover protection (ROPS) and keep all machinery guards in place... Please work, drive, play and live each day with care and concern for your safety and that of your family and fellow citizens.
R 7 REV 05-3 Printed U.S.A. P/N 007800P