K16 DOORS K16.14 01.06.2017 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com
CONTENTS 1. General... K16.14.03 1.1. General information K16.14.03 1.2. Explanation dimensions K16.14.03 1.3. Explanation normal type and VI type K16.14.03 1.4. Care tips K16.14.03 2. Door pulls... K16.14.04 2.1. 1870/1871 K16.14.04 2.2. 1770/1771 K16.14.04 2.3. 1875/1876 K16.14.05 2.4. 1776 K16.14.05 2.5. 1863/1864 K16.14.06 2.6. 1867/1868 K16.14.06 2.7. 1873/1874 K16.14.07 2.8. 1878/1879 K16.14.07 2.9. 1882/1883 K16.14.08 2.10. 1884/1885 K16.14.08 2.11. 1861/1862 K16.14.09 2.12. 1888/1889 K16.14.09 2.13. 1887 K16.14.10 2.14. 1787/1788 K16.14.10 2.15. 1869 K16.14.11 3. Fixing sets...k16.14.12 3.1. Single-sided fixing K16.14.12 3.2. Double-sided fixing K16.14.13 3.3. Single-sided fixing at 30 on aluminium or timber doors K16.14.14 3.4. Double-sided fixing at 30 on aluminium or timber doors K16.14.14 3.5. Invisible fixing K16.14.15 K16.14.02
1. General 1.1. General information The SOBINOX door pulls are manufactured from high-grade stainless steel AISI 304. The SOBINOX door pulls are supplied with a satin finish. These door pulls can be used in many different sectors due to their aesthetic, practical, maintenance friendly and hygienic properties: e.g. private houses, hospitals, catering, industry,... The fixing sets must be ordered separately and are available for different section depths. You will find more information about the fixing sets on pages K16.14.12 to K16.14.16. The door pulls are non-handed. 1.2. Explanation dimensions A = length between fixing holes B = depth C = width D = diameter E = side L = overall length VI = with invisible fixing (non-threaded and can only be used with small press screws) 1.3. Explanation normal type and VI type VI type normal type inside outside 1.4. Care tips Maintenance should be carried out at suitable intervals to prevent surface corrosion and for reasons of hygiene. Normal maintenance Clean the stainless steel parts regularly Treat the surface with soapy water or with a mild detergent Rinse of the detergent with clean water Polish with a soft cloth or sponge Never use Scouring powders Steel wool or steel brushes Highly abrasive materials K16.14.03
2. Door pulls 2.1. 1870/1871 Order code A (mm) B (mm) C (mm) D (mm) 1870-250 250 75 100 25 1870-250 VI 250 75 100 25 1870-300 300 75 100 25 1870-300 VI 300 75 100 25 1870-350 350 75 100 25 1870-350 VI 350 75 100 25 1870-400 400 75 100 25 1870-400 VI 400 75 100 25 1871-300 300 85 125 30 1871-300 VI 300 85 125 30 1871-350 350 85 125 30 1871-350 VI 350 85 125 30 1871-400 400 85 125 30 1871-400 VI 400 85 125 30 This type is available made to measure with diameter 25 or 30 mm and with hole centres (A) from 200 to 2000 mm. 2.2. 1770/1771 Order code A (mm) B (mm) D (mm) 1770-300 300 75 25 1770-300 VI 300 75 25 1770-500 500 75 25 1770-500 VI 500 75 25 1771-300 300 77 30 1771-300 VI 300 77 30 1771-500 500 77 30 1771-500 VI 500 77 30 This type is available made to measure with diameter 25 or 30 mm and with hole centres (A) from 200 to 2000 mm. K16.14.04
2.3. 1875/1876 Order code A (mm) B (mm) C (mm) D (mm) 1875-200 200 75 140 25 1875-200 VI 200 75 140 25 1875-300 300 75 190 25 1875-300 VI 300 75 190 25 1876-300 300 85 210 30 1876-300 VI 300 85 210 30 2.4. 1776 Order code A (mm) B (mm) D (mm) 1776-300 300 89.5 30 1776-300 VI 300 89.5 30 K16.14.05
2.5. 1863/1864 Order code A (mm) B (mm) D (mm) L (mm) 1863-200 200 75 25 300 1863-200 VI 200 75 25 300 1863-300 300 75 25 400 1863-300 VI 300 75 25 400 1863-400 400 75 25 500 1863-400 VI 400 75 25 500 1863-500 500 75 25 600 1863-500 VI 500 75 25 600 1864-400 400 85 30 500 1864-400 VI 400 85 30 500 1864-500 500 85 30 600 1864-500 VI 500 85 30 600 This type is available made to measure with diameter 25 or 30 mm and with hole centres (A) from 200 to 2000 mm. 2.6. 1867/1868 Order code A (mm) B (mm) D (mm) L (mm) 1867-200 200 75 25 300 1867-200 VI 200 75 25 300 1867-300 300 75 25 400 1867-300 VI 300 75 25 400 1867-400 400 75 25 500 1867-400 VI 400 75 25 500 1867-500 500 75 25 600 1867-500 VI 500 75 25 600 1868-400 400 85 30 500 1868-400 VI 400 85 30 500 1868-500 500 85 30 600 1868-500 VI 500 85 30 600 This type is available made to measure with diameter 25 or 30 mm and with hole centres (A) from 200 to 2000 mm. Note: this type is provided with a slanting support and is fixed on the door at an angle of 30. K16.14.06
2.7. 1873/1874 Order code A (mm) D (mm) 1873-300 300 25 1873-300 VI 300 25 1873-650 650 25 1873-650 VI 650 25 1874-300 300 30 1874-300 VI 300 30 1874-500 500 30 1874-500 VI 500 30 1874-650 650 30 1874-650 VI 650 30 1874-770 770 30 1874-770 VI 770 30 2.8. 1878/1879 Order code A (mm) B (mm) D (mm) 1878-300 300 75 25 1878-300 VI 300 75 25 1878-650 650 75 25 1878-650 VI 650 75 25 1879-300 300 85 30 1879-300 VI 300 85 30 1879-500 500 85 30 1879-500 VI 500 85 30 1879-650 650 85 30 1879-650 VI 650 85 30 1879-1000 1000 85 30 1879-1000 VI 1000 85 30 This type is available made to measure with diameter 25 or 30 mm and with hole centres (A) from 200 to 2000 mm. K16.14.07
2.9. 1882/1883 Order code A (mm) B (mm) D (mm) 1882-300 300 75 25 1882-300 VI 300 75 25 1882-500 500 107 25 1882-500 VI 500 107 25 1883-300 300 75 30 1883-300 VI 300 75 30 1883-500 500 107 30 1883-500 VI 500 107 30 2.10. 1884/1885 Order code A (mm) B (mm) D (mm) 1884-300 300 45 25 1884-300 VI 300 45 25 1884-500 500 55 25 1884-500 VI 500 55 25 1885-300 300 47 30 1885-300 VI 300 47 30 1885-500 500 58 30 1885-500 VI 500 58 30 Note: this type is provided with a slanting support and is fixed on the door at an angle of 30. K16.14.08
2.11. 1861/1862 Order code A (mm) B (mm) D (mm) 1861-300 300 75 25 1861-300 VI 300 75 25 1861-350 350 75 25 1861-350 VI 350 75 25 1861-400 400 75 25 1861-400 VI 400 75 25 1862-300 300 85 30 1862-300 VI 300 85 30 1862-350 350 85 30 1862-350 VI 350 85 30 1862-400 400 85 30 1862-400 VI 400 85 30 This type is available made to measure with diameter 25 or 30 mm and with hole centres (A) from 200 to 2000 mm. 2.12. 1888/1889 Order code A (mm) E (mm) 1888-300 300 25 1888-300 VI 300 25 1888-500 500 25 1888-500 VI 500 25 1889-300 300 30 1889-300 VI 300 30 1889-500 500 30 1889-500 VI 500 30 1889-650 650 30 1889-650 VI 650 30 This type is available made to measure with side 25 or 30 mm and with hole centres (A) from 200 to 2000 mm. K16.14.09
2.13. 1887 Order code A (mm) L (mm) 1887-350 350 500 1887-350 VI 350 500 1887-500 500 700 1887-500 VI 500 700 This type is available made to measure with diameter 30 mm and with hole centres (A) from 200 to 2000 mm. 2.14. 1787/1788 Order code A (mm) B (mm) C (mm) D (mm) 1787-350 350 75 47 25 1787-350 VI 350 75 47 25 1788-500 500 85 69 30 1788-500 VI 500 85 69 30 K16.14.10
2.15. 1869 Order code A (mm) 1869-300 300 1869-300 VI 300 1869-500 500 1869-500 VI 500 K16.14.11
3. Fixing sets 3.1. Single-sided fixing Fixing on glass doors Fixing on aluminium or timber doors Parts 1) screw bolt for single-sided fixing M10 6) decorative nut 2) plastic washer 7) plastic washer 3) guide bush (for glass door) 8) threaded rod Order table Order code Material of the door Length threaded rod Section depth X Diameter door pull 1890-25 glass - - 25 1890-30 glass - - 30 1891-25-70 alu/timber 70 32-47 25 1891-30-70 alu/timber 70 32-47 30 1891-25-85 alu/timber 85 47-62 25 1891-30-85 alu/timber 85 47-62 30 1891-25-100 alu/timber 100 62-77 25 1891-30-100 alu/timber 100 62-77 30 1891-25-115 alu/timber 115 77-92 25 1891-30-115 alu/timber 115 77-92 30 K16.14.12
3.2. Double-sided fixing Fixing on glass doors VI type normal type Fixing on aluminium or timber doors VI type normal type Parts 2) plastic washer 3) guide bush (for glass doors) 4) screw bolt M10 for double-sided fixing 5) inner washer 9) screw bolt for double-sided fixing 10) hexagon socket screw M5 Order table Order code Material of the door * Total length of the screw bolt Length threaded rod Section depth X Diameter door pull P1890-25 glass - - 25 P1890-30 glass - - 30 P1891-25-90 alu/timber 90* 32-47 25 P1891-30-90 alu/timber 90* 32-47 30 P1891-25-105 alu/timber 105* 47-62 25 P1891-30-105 alu/timber 105* 47-62 30 P1891-25-120 alu/timber 120* 62-77 25 P1891-30-120 alu/timber 120* 62-77 30 P1891-25-135 alu/timber 135* 77-92 25 P1891-30-135 alu/timber 135* 77-92 30 P1891-25-150 alu/timber 150* 92-107 25 K16.14.13
3.3. Single-sided fixing at 30 on aluminium or timber doors The set contains 2 threaded rods, 2 decorative nuts and 2 fixing rings. This set is not available for glass doors. Order code Length B threaded rod Section depth A Diameter door pull 1894-50 50 23-33 1894-60 60 33-43 1894-70 70 43-53 1894-80 80 53-63 1894-90 90 63-73 1894-100 100 73-83 1894-110 110 83-93 25 or 30 3.4. Double-sided fixing at 30 on aluminium or timber doors VI type normal type The set contains 2 threaded rods for double-sided fixing and 4 fixing rings. Order code Length B threaded rod Section depth A Diameter door pull P1894-60 60 23-33 P1894-70 70 33-43 P1894-80 80 43-53 P1894-90 90 53-63 P1894-100 100 63-73 P1894-110 110 73-83 P1894-120 120 83-93 P1894-130 130 93-103 25 or 30 K16.14.14
3.5. Invisible fixing Invisible fixing on aluminium doors Parts 1) door pull 4) threaded rod 2) tensioning ring 5) clamping piece 3) spring washer 6) screw cap Order code Diameter door pull 1892-25 25 1892-30 30 Invisible fixing on timber doors Parts 1) door pull 7) threaded rod 2) tensioning ring 8) fixing screw 3) spring washer Order code Diameter door pull 1893-25 25 1893-30 30 K16.14.15
Invisible fixing set n 1896-.. on aluminium, PVC or timber doors The sets can only be used for door pulls type VI. Thread-cutting fixing screws in stainless steel. Drill holes with diameter 9.5 mm. A set contains 2 screws and the corresponding fixing rings. VI type Order code Diameter door pull 1896-25 25 1896-30 30 Invisible fixing set n 1897 with slanting support on aluminium, PVC or timber doors The set can only be used for door pulls type VI. Thread-cutting fixing screws in stainless steel. Drill holes with diameter 9.5 mm. A set contains 2 screws and the corresponding fixing rings. VI type K16.14.16