HWB HPP Power being equal our pump is the smallest, the lightest and the most economical in price worldwide! THE ULTIMATE COLD WATER HIGH PRESSURE SYSTEM HIGH PRESSURE HYDRAULICALLY DRIVEN PRESSURE WASHER COMPACT VERSATILE EXTREME PRESSURE TRANSFORMS AVAILABLE HYDRAULIC POWER INTO ANY FLUID MULTIPLYING THE PRESSURE Patented Primary fluid Oil, vegetable oil, emulsion 80-280 bar /1160-4060 psi Secondary fluid Oil, water, chemicals 50-1200 bar / 725-17400 psi DISTRIBUTOR www.neron.it E-mail:info@neron.it
HIGH PRESSURE WATER JETTING APPLICATIONS Service Vehilces: road cleaning, pipe cleaning Asphalt machines: immediate removal of hot asphalt Sweepers: high pressure cleaning; dust suppression Fork lifts: maintenance, high pressure cleaning Communal truck: all kinds of communal cleaning jobs Fire fighting vehicles: for civil protection Tractors: cleaning, sandblasting, flushing Fire fighting vehicles: pumps with water spray Industrial Drilling Rigs: cooling, cleaning joints and threads Sludge Suction Truck: cleaning pipes and outflows High pressure washing system: on vehicles for applying herbisides or pesticides Excavators: cleaning, drainage, sacrificial Concrete pumps: cleaning of the concrete hopper and tubes Concrete truck: removing concrete and solid debris Hydraulic lift: use hydraulic tools especially sevice on eletrical cables Forest fire fighting vehicles: to save vegitation in environment sensitive regions Fishing boats: cleaning sandblasting, net cleaning Power packs: for mobile application Maintenance of railway vehicles: rails cleaning Cleaning system with high pressure chemical injector: new cleaning system Dust suppression: with water sprays Tunnel cleaning and underground: cleaning of smoke, gas and dirt contamination from wall Pipe cleaning with canal jet: for sand and mug removal Machines: ease and lubricated oil pumping under pressure Cutting machines with water: for water cutting of plastic materials Plaster machines: cleaning of hard plaster and sacrificial Cleaning of fish farming and animal farming with chemical injector: with chemicals cleaning of environmental or animal, stables Environmental cleaning, food firms with chemical injector: for an accurate cleaning and disinfectation ROV application: system for maintenance, check-up, repair of special subsea machines, fluid injector pressure washer. (Bennex concession) SPECIAL APPLICATIONS Tube and hydroforming repair operation: tubes repair subsea system. (Snam-ENI concession) Test benches: for high performance tests, burst test and material deformation AND ANY OTHER CLEANING APPLICATIONS WITH COLD WATER HIGH PRESSURE
Water suction filter and self cleaning filter up to 2000 kpa (290psi) Water hose bard Selfrecoiling hose reel Single lances 3625psi, quick connectors and nozzle protection Sand blasters Calculated flow & pressure limiting valve block to be connected to the Neron pumps Rotating nozzles 2175-5075psi Pressure gauge 0-5800psi Spray guns 3600-5000psi Double lances 4060psi, quick connectors low pressure & high pressure nozzle, nozzle protection Low & high pressure nozzles Drain cleaning nozzles Canal jet, sewer cleaning 10-20 mt Hoses 5/16 R1-R2 Screw Swivel ends M22 F-M Spray foam nozzle Chemical injectors Rotating brush 3000psi bar 30 l/m = 7.9gpm Water ball type quick coupling Water ball type quick coupling Oil quick couplings SLUDGET PUMP The Neròn pump is connected directly on the output of the water Neron pump. The water at high pressure (from 1400psi to 2900psi) creates a vacuum in the sludge pump body, sucking by the Venturi principle some water, up to 52gpm and/or mug other solid substance with a diameter up to 1/2 Performance Chart USES - Emptying of foundation, conduits, mandole, basement - Tanks replenishment - Fire protection - Fire prevention - Pouring off any type of liquid - Special applications can be investigated in various diameters In order to avoid cavitation, do not exceed the allowed oil inlet flow values stated at Q1. Reduce the oil inlet flow of the main hydraulic system or install a flow limiting valve block to be flanged into the Neròn Pump oil inlet. Accessories are generally used with by-pass and automatic version
PRINCIPLE The hydraulic system energy is used to activate three axial Pistons which are directly coupled to output pressure pump pistons which directly and continuously transfer available hydraulic power. (P1 x Q1) Providing hydraulic pumping power transformed into outlet pressure (P2) at corresponding flows (Q2) to a fluid. This design allows for a compact high pressure reliable pumping system. DUAL FLUID ENERGY TRANSFORMATION Primary and secondary circuits are hemispherically separated to allow for different drive and driven fluids. Oil another liquid fluid (water) Oil inflammable fluid Oil Vegetable Oil Oil emulsion oil 1. BYPASS (HWB 150-200-250-300) Primary circuit (drive) Housing relief valve Optional flow/pressure compensation valve Secondary Circuit Adjustable pressure bypass valve Thermal valve protection Low pressure, bypass circuit Low power consumption in by pass mode 2. Automatic (HPP318-615-813-415-418-613) Primary circuit (drive) Housing relief valve Optional flow/pressure compensation valve Secondary circuit constant discharge pressure controlled by regulating primary oil flow Both primary and secondary pumps are over pressure protected. 3. Base (HP 812-810-808-1408 HPP 415-418-613) Primary circuit (drive) Housing relief valve Optional flow/pressure compensation valve Secondary Circuit Low pressure/high volume - high pressure/low volume staged system Pump will begin operation once a preset pressure has been achieved. Dual circuit allows for pump to be used as a boost system. HWB BY-PASS HPP 415-418-613 HPP 318-615-813 LEGEND: A = T2 Water inlet 3/4 ORB/Male B = P2 Water outlet M22M (HWB-HPP) + 1/4 GAS/F () C = T1 Oil return port tothe tank 1/2 ORB/Female D = P1 Oilpressure port 1/2 ORB/Female E = Oil protection valve F = Pressure limiting valve atp2 for version By-Pass /Base /Automatic G = Chemical injector H = Thermal valve or water by-pass totank SPECIFICATIONS: Max height 5 mt Max water temperature 80 C; 145 F Minimum oil flow at P1: 10 l/m; 2.6 gmp (HWB) - 20 l/m; 5.2 gpm (HPP-) Max oil temperature: 80 C; 145 F NERON, IN A CONTINUED COMMITMENT TO IMPROVE QUALITY, RESERVE THE RIGHT TO MAKE COMPONENT OR DESIGN CHANGES WHEN NECESSARY, WITHOUT NOTICE
PUMPS TYPES AND FEATURES HWB 100 15 l/m-3.9gpm 18 l/m-4.7gpm 20 l/m-5.2gpm 125 bar-1810 psi 180 bar-2610 psi 185 bar-2680 psi 18 l/m-4.7 gpm 22 l/m-5.8 gpm 24 l/m-6.3 gpm 70 bar-1015 psi 90 bar-1300 psi 100 bar-1450 psi 1.9 1.9 2.1 15 l/m-3.9gpm 22 l/m-5.8gpm 220 bar-3 190 psi 230 bar-3 330 psi 250 bar-3 620 psi 22 l/m-5.8 gp m 26 l/m-6.8 gp m 30 l/m-7.9 gp m 135 bar-1950 psi 145 bar-2100 psi 1.7 1.9 2.1 HWB 200 15 l/m-3.9gpm 170 bar-2460 psi 175 bar-2530 psi 145 bar-2100 psi 16 l/m-4.2gpm 21 l/m-5.5 gpm 25 l/m-6.6 gpm 125 bar-1810 psi 130 bar-1885 psi 110 bar-1600 psi 1.5 1.7 2.1 18 l/m-4.7gpm 23 l/m-6 gpm 135 bar-1 950 psi 14 l/m-3.7gpm 150 bar-2170 psi 1.2 190 bar-2 750 psi 215 bar-3 110 psi 16 l/m-4.2 gp m 18 l/m-4.7 gp m 225 bar-3260 psi 250 bar-3620 psi 1.2 1.15 HWB 300 HWB 250 18 l/m-4.7gpm 22 l/m-5.8gpm 150 bar-2170 psi 9 l/m-2.3gpm 12 l/m-3.2 gpm 13 l/m-3.4 gpm 185 bar-2680 psi 180 bar-2610 psi 215 bar-3115 psi 0.95 1.1 1.15 20 l/m-5.3gpm 23 l/m-6 gpm 110 bar-1 600 psi 110 bar-1 600 psi 150 bar-2 175 psi 7 l/m-1.85gpm 9 l/m-2.4 gpm 9 l/m-2.4 gpm 210 bar-3050 psi 200 bar-2900 psi 300 bar-4350 psi 0.80 0.90 0.8 HWB 150 HWB 400 * Testing & calibration performed at the factory on each pump. Different calibration upon customer request. Values are subject to the oil temperature of the hydraulic system. The HWB 150-200-250-300-400, HPP & pumps are available with the flow limiting valve block up to 80 l/m Use with fresh & salt water By changing the nozzle size with a smaller one the pump will self adjust: dust surpression (low pressure) & high pressure wash HWB- working with by-pass valve incorporated Integrated system fully lubricated Integrated pressure relief valve THE ABOVE DATA ARE THE EQUIVALENT OF AN AVERAGE BETWEEN THE THEORIC QUOTES AND THE TEST RESULTS.
PUMPS TYPES AND FEATURES 1 wand 2 wand 40 l/m10.5gpm 185 bar-2680 psi 40 l/m10.5gpm 185 bar 2680 psi 24 l/m-6.3 gpm 100 bar-1450 psi 1.9 100 bar-1450 psi 1.9-1.9 12+12l/m-3.15+3.15gpm PU MP TYP E W OR K IN G C ON D ITIO N 1818 1 wand 2525 1 wand 2 wand 2 wand O IL IN LET FLO W (Q 1) OIL IN LET PR ESS UR E (P 1) 200 bar- 2900psi 200 ba r-2900 psi 270 bar- 4000psi 270 ba r-4000 psi PUMP TYPE FLOW (Q1 ) PRESSUR E (P2) HPD 318 HPD 615 HPD 813 50 lm-13.2gpm 220 bar-3190 psi 36 l/m-9.5 gpm 250 bar-3600 psi 1.3 50 lm-13.2gpm 50 lm-13.2gpm 190 bar-2750 psi 180 bar-2600 psi 20 l/m-5.2 gpm 17 l/m-4.5 gpm 290 bar-4200 psi 330 bar-4800 psi 0.9 0.8 HPP 60 l/m- 16gpm 30+ 30 l/m-8+8 gpm 240 240 160 160 bar-3500 psi bar-3500 psi bar-2300 psi bar-2300 psi HPD HPP 415 11 l/m-2.9 gpm 180 bar-2610 psi 1.10 HPP 418 HPP 613 200 bar-2900 psi 16 l/m-4.2 gpm 16 0 bar 2320 psi 8,5 l/m-2.2 gpm 235 bar-3400 psi 300 bar-4350 psi 1.20 0.80 810 812 808 200 bar-2 900 psi 260 bar-3 750 psi 5.5 l/m-1.4gpm 800bar-11600 psi 8 l/m-2.15 gp m 750 bar-10875psi 25 l/m-6.6 pm 140 bar-2 030 psi 4 l/m-1.05 gp m 900 bar-13050psi FLOW (Q1 ) PRESSUR E (P2) HPP 318 HPP 615 HPP 813 220 bar-3190 psi 18 l/m-4.8 gpm 250 bar-3600 psi 1.3 190 bar-2750 psi 180 bar-2600 psi 10 l/m-2.6 gpm 8.5 l/m-2.2 gpm 290 bar-4200 psi 330 bar-4800 psi 0.9 0.8 HPP HWB 8-12 Kg WATEROUTPUT 8,5 Kg Fixing holes M8 HPP H 20 Kg Fixing holes M8 180 240 Fixing holes M8 20 l/m-5.3gpm 80 bar-1150 psi 1.1 l/m-0.3gpm 1100 bar-15950psi 25 l/m-5.3gpm 100 bar-1450 psi 1.3l/m-0.35 gpm 1250 bar-18120 psi PUMP TYPE 18 Kg 32 l/m -8.4gp m 1 6+1 6l/m -4.2 +4.2 gp m WA TER O U TPU T P RESS U RE (P 2) W A TER O UTP UT F LOW (Q2) PUMP TYPE PUMP TYPE 10 10 TECHNICAL CHANGES AND COPYRIGHT RESERVED