Bauart gepruft Sicherheit egelma ge od o s be wac g 600W Intelligent Single Output Charger PB600 series SPECIFICATION SAFETY & EMC (Note 3) SAFETY STANDARDS WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION MODEL PB60012 PB60024 PB60048 BOOST CHARGE VOLTAGE 14.4V 28.8V 57.6V FLOAT CHARGE VOLTAGE Vfloat 13.8V 27.6V 55.2V OUTPUT RECOMMENDED BATTERY 135 ~ 400AH CAPACITY(AMP HOURS)(Note 4) 70 ~ 210AH 35 ~ 105AH BATTERY TYPE Open & Sealed Lead Acid OUTPUT CURRENT 40A 21A 10.5A VOLTAGE RANGE FREQUENCY RANGE 0 ~ 264VAC 47 ~ 63Hz 127 ~ 370VDC POWER FACTOR (Typ.) 0.5/230VAC 0.8/115VAC at full load INPUT EFFICIENCY (Typ.) 86% 87% 8% AC CURRENT (Typ.) 6.8A/115VAC 3.4A/230VAC INRUSH CURRENT (Typ.) LEAKAGE CURRENT 25A/115VAC <3.5mA / 240VAC 50A/230VAC 16 ~ 18V 32 ~ 35V 64.5 ~ 6.5V OVER VOLTAGE PROTECTION Protection type : Shut down o/p voltage, repower on to recover OVER TEMPERATURE Protection type : Shut down o/p voltage, recovers automatically after temperature goes down REMOTE Open: Normal work Short: Stop LEAKAGE CURRENT FROM BATTERY (Typ.) 1mA FUNCTION FAST CHARGE 2 / 3 / 8 stage selectable CHARGER OK Relay contact (RY15) OUTPUT OK Relay contact (RY13) TEMPERATURE SENSE By NTC WORKING TEMP. 20 ~ 60 (Refer to "Derating Curve") WORKING HUMIDITY 20 ~ 0% RH noncondensing ENVIRONMENT STORAGE TEMP., HUMIDITY 40 ~ 85, 10 ~ 5% RH TEMP. COEFFICIENT ± 0.05%/ (0 ~ 50 ) VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes OTHERS NOTE EMC IMMUNITY UL1012, TUV EN603351, EN6033522 (except for 48V), EN60501(48V only) approved I/PO/P:3KVAC I/PFG:2KVAC O/PFG:0.5KVAC I/PO/P, I/PFG, O/PFG:100M Ohms / 500VDC / 25 / 70% RH Compliance to EN55022 class B (CISPR22), EN6100032,3 Compliance to EN6100042,3,4,5,6,8,11, EN55024; light industry level, criteria A MTBF 135.6K hrs min. MILHDBK217F (25 ) DIMENSION 230*158*67mm(L*W*H) PACKING 2.2Kg; 6pcs/14.2Kg/1.76CUFT www. tuv.com ID 2000000000
10 600W Intelligent Single Output Charger PB600 series Mechanical Specification Case No.805C Unit:mm 230 67 7 145 42.5 ON OFF ON/OFF SWITCH 158 67 33 48 Air flow direction AC INPUT INLET 24.1 LED Loading Indicator Status Table Status Color Red Steady Abnormal status Full Flashing Control Pin No. Assignment( ) : HRS DF1110DP2DS or equivalent 7 5 3 1 10 8 6 4 2 Mating Housing Terminal HRS DF1110DS or equivalent HRS DF11**SC or equivalent Pin No. Function Description 1,2 RY13 RY13 : Bank OK relay. Relay contact rating(max.) : 30V/1A resistive. ; "Short" when the battery is full, "Open" when the battery is still charging. RY15 : Charger OK relay. 5,6 RY15 Relay contact rating(max.) : 30V/1A resistive. ; "Short" when the unit is working properly, "Open" when the unit is failure or the protection function is activating. 7 8,10 NTC / : Temperature sense Temperature sensor comes along with the charger can be connected to the unit to allow temperature compensation of the NTC(5K Ω) charging voltage Remote ON/OFF function. RC / RC Turn the output on and off by electrical or dry contact between pin 10 (RC) and pin (RC). "Open" : Normal work ; "Short" : Stop charging
600W Intelligent Single Output Charger PB600 series Block Diagram PFC : 5KHz PWM fosc : 60KHz I/P EMI FILTER ACTIVE INRUSH CURRENT LIMITING RECTIFIER & PFC POWER SWITCHING RECTIFIER & FILTER V PFC AUX POWER PWM FAN OTP CURRENT DETECTION MCU REVERSE DETECTION 2/8 STAGE SELECT REMOTE RC Bank OK RY13 Charger OK RY15 Derating Curve Static Characteristics 100 80 60 100 0 80 70 LOAD (%) 40 20 LOAD (%) 60 50 40 20 0 10 20 30 40 50 60 70 (HORIZONTAL) AMBIENT TEMPERATURE ( ) 0 5 100 115 264 INPUT VOLTAGE (VAC) 60Hz Curve 2 Stage 3 Stage Start Start Vfloat 100% 100% Charge Current Constant Current 10% 10% Constant Voltage Charge Current Constant Current Constant Voltage Float stage 1 stage 2 stage 1 stage 2 stage 3 State Constant Current PB60012 14.4V PB60024 PB60048 40A 21A 10.5A 28.8V 57.6V Suitable for leadacid batteries (flooded, Gel and AGM) and Liion batteries (lithium iron and lithium manganese). State Constant Current Vfloat PB60012 14.4V 13.8V PB60024 28.8V 27.6V PB60048 40A 21A 10.5A 57.6V 55.2V Suitable for leadacid batteries (flooded, Gel and AGM) and Liion batteries (lithium iron and lithium manganese).
600W Intelligent Single Output Charger PB600 series 8 Stage Pulse Soft Start Constant Current Constant Voltage Analysis Recond Float Maintain Charge Current stage 1 stage 2 stage 3 stage 4 stage 5 stage 6 stage 7 stage 8 Loading Indicator Suitable for leadacid batteries (flooded, Gel and AGM). stage 1 (Pulse) and stage 2"(Soft Start) provide battery rescue function. 2,3, or 8 stage charging select (1)The charger features user selectable 2,3, or 8 stage charging. The charging profile is selected by moving the slide switch on the back panel. Switch mode Right 2 stage charging Middle 3 stage charging Left 8 stage charging (2)Please choose the "3 stage" selection when the charger is used to charge the batteries and power the loads in the same time. Function Manual 1.Remote Control The charger can be turned ON/OFF by using the "Remote Control" function. Between RC(pin10) and RC(pin) SW Open SW Short ON OFF 1 RY13 RY13 2 10 1 RY13 RY13 2 RC RC 10 RC RC SW
600W Intelligent Single Output Charger PB600 series 2.Charger OK Relay(RY15) Charger Work normally Failure or protection function activated Between pin5 and pin6(ry15) ON (Short) OFF (Open) 1 RY13 RY13 2 RC RC 10 RY15 3.Output OK Relay (RY13) 1.Bank OK (RY13) Bank Between pin1 and pin2(ry13) RY13 RY13 Full ON (Short) OFF (Open) RC RC 10 RY13 4.Temperature compensation Temperature sensor comes along with the charger can be connected to the unit to allow temperature compensation of the charging voltage. If the sensor is not used, the charger still works normally. 1 RY13 RY13 2 RC RC 10 NTC The temperature sensor can either be attached to the battery or placed in its surrounding environment. Installation Manual Please refer to the manual of PB600.