INSTLLTION INSTRUCTIONS FOR PRT 95-733 PPLICTIONS 00-006 Hyundai Elantra 003-008 Hyundai Tiburon 00-005 Hyundai Sonata 00-006 Kia Optima (006 Early Production Models Only) 95-733 KIT FETURES DDIN Head Unit Provision STCKED ISO DIN Head Unit Provision KIT COMPONENTS ) DDIN Trim Plate ) DDIN rackets TOOLS REQUIRED: Flat lade Screwdriver I Phillips Screwdriver
00-006 HYUNDI ELNTR 3 4 5 Disconnect the negative battery terminal to prevent an accidental short circuit. Remove () Phillips screws from under the instrument cluster. Remove ashtray then remove () Phillips screws in ashtray cavity. Unclip and remove panel surrounding radio. (Figure ) Remove (4) Phillips screws securing radio. DSH DISSSEMLY
003-008 HYUNDI TIURON DSH DISSSEMLY 3 Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip and remove the radio trim panel starting with the bottom edge. (Figure ) Remove () Phillips screws securing radio.
00-005 HYUNDI SONT 00-005 KI OPTIM 3 4 Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip and remove entire panel surrounding radio. (Figure ) Remove (4) Phillips screws securing radio. The rear support bar in the sub dash will need to be cut and removed for aftermarket radio clearance. (Figure ) DSH DISSSEMLY
006 KI OPTIM(006 Early Production Models Only) DSH DISSSEMLY 3 4 5 Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip and remove panel surrounding shifter. (Figure ) Remove () Phillips screws at bottom of panel surrounding radio and climate control then unclip and remove entire panel. (Figure,C) Remove (4) Phillips screws securing radio. (Figure D) The rear support bar in the sub dash will need to be cut and removed for aftermarket radio clearance. (Figure E) D C E
DOULE DIN HED UNIT PROVISION Slide the appropriate bracket into the trim plate aligning the holes in the trim plate to the clips on the bracket. (Figure ) Slide the DDIN radio unit into the trim plate bracket assembly and secure the unit to the kit using the screws supplied with the head unit. (Figure ) KIT SSEMLY NOTE: For the 003-008 Hyundai Tiburon applications you will need to cut and remove the bottom mounting tabs on the DDIN brackets. (Figure C) C CUT CUT
STCKED ISO DIN HED UNIT PROVISION KIT SSEMLY Slide the appropriate bracket into the trim plate aligning the holes in the trim plate to the clips on the bracket. (Figure ) Slide the stacked ISO DIN units into the trim plate bracket assembly and secure the unit to the kit using the screws supplied with the head unit. (Figure ) NOTE: For the 003-008 Hyundai Tiburon applications you will need to cut and remove the bottom mounting tabs on the DDIN brackets. (Figure C) C CUT CUT
FINL SSEMLY Locate the factory wiring harness in the dash and make the connection as shown. Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly. FINL WIRING CONNECTIONS 95-733 FINL SSEMLY Make wiring connections using the EI color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit. C ) Strip wire ends back /" ) Twist ends together C) Solder D) Tape D METR / EI WIRING CODE V Ignition / cc... Red V att / Memory.. Yellow Ground........... lack* Power ntenna..... lue mp Turn-On...... lue / White mp Ground....... lack / White Illumination........ Orange Dimmer.......... Orange / White Right Front (+)..... Gray Right Front (-)...... Gray / lack Left Front (+)...... White Left Front (-)....... White / lack Right Rear (+)...... Violet Right Rear (-)...... Violet / lack Left Rear (+)....... Green Left Rear (-)....... Green / lack *NOTE: When lack a wire is not present, ground radio to vehicle chassis. ll colors may not be present on all leads due to manufacturer s specifications. METR CCESSORIES STEREO DSH KITS