Lifting Gear Hire Jacking

Lifting Gear Hire Jacking All rental equipment is available throughout North America. For specific product information, refer to the group of equipment within this section s overview on the following page for that product s corresponding page number. Rentals@RentLGH.com Jacking Equipment Lifting Gear Hire stocks a complete range of equipment for virtually any lifting or moving application. Some of the industries we serve: Energy Utilities Construction Maintenance Transportation Marine/Ship Building Petrochemical Pharmaceutical 134

Jacking Section Overview Jacking Types Manufacturer(s) Pages Reel Jacks, Ratchet Jacks, Superjacks Simplex 136 138 Air Bags Mat Jack 139 Hydraulic s 5 100 Ton Single-Acting, Spring Return Hydraulic s 5 100 Ton Single-Acting, Spring Return, Low-Profile Hydraulic s 60 600 Ton Single-Acting, Load Return, Pancake Lock Nut Hydraulic s 50 1,000 Ton Single-Acting, Load Return, Lock Nut Hydraulic s 30 150 Ton Double-Acting, Center Hole Hydraulic s 150 500 Ton Double-Acting Hydraulic s 50 200 Ton Double-Acting Hydraulic s 50 300 Ton Single-Acting, Load Return Hydraulic s 400 1000 Ton Single-Acting, Load Return Enerpac 140 Simplex 150 152 Enerpac 141 Simplex 154 Enerpac 142 Enerpac 143 Enerpac 144 Enerpac 145 Enerpac 146 Enerpac 147 Enerpac 148 Hydraulic s Enerpac 149 12 100 Ton Single-Acting, Spring Return, Center Hole Simplex 157 Hydraulic s 5 150 Ton Single-Acting, Spring Return, Low-Profile Simplex 153 Hydraulic s 10 1,000 Ton Double-Acting Simplex 155 Hydraulic s 30 1,000 Ton Single-Acting, Load Return, Lock Nut Simplex 156 Hydraulic s 30 1,000 Ton Single-Acting, Load Return Simplex 158 Hand Pumps, Gas Pumps, Electric Pumps Simplex, Enerpac 159 162 Accessories Simplex 163 166 Spreader Jacks, Toe Jacks Simplex, Tangye 167 169 Hydra-Pac Synchronous Pump & Heavy Track Skidding System Hydra-Slide 170 172 Sync Lift Enerpac 173 174 www.rentlgh.com Jacking Equipment 135

Mechanical Jacks 5 20 Ton Reel Jack 321B Using A1029-R and A1029-L, utilities can easily handle large reels. The large wooden bases and low handle efforts enhance safety and reduce operator fatigue. Simplex Reel Jacks are also an excellent choice for wire rope and sling manufacturers. Rentals@RentLGH.com Jacking Equipment 320B With three hooks; top fits up to 2-1 /2 inch spindles; side hooks fit up to 2 inch spindles. 321B (shown above) With five hooks; top fits up to 3-1 /2 inch spindles, next hook down fits up to 3 inch spindles, and lowest three fit up to 2-3 /8 inch spindles. This model is recommended for use on firm surfaces. A1029 The A1029 has a light weight aluminum alloy housing and three hooks; top fits up to 3 inch spindles, side hooks fit up to 2 3 /8 inch spindles. Equipped with right or left-handed t-base, supported by three adjustable steel rods to provide a sturdy, non-rocking foundation for outside use. Caps swivel for easy reel mounting. Steel lever bars are ordered separately. per Pair Side Hooks (Tons) Top Hooks (Tons) Handle Effort per Ton Stroke Reel Dia. Top Hook Order Number Steel Lever Bars Length Diameter 320B 5 10 32 10 20-60 21 51 10640 36 1 8 321B 10 20 22 12 20-96 34 1 /2 128 *10665 60 1 1 /4 17 A1029-R 10 20 22 11 5 /8 36-84 31 1 /8 86 *10665 60 1 1 /4 17 A1029-L 10 20 22 11 5 /8 36-84 31 1 /8 86 *10665 60 1 1 /4 17 *Lever bar 10675 can be substituted resulting in lower handle effort. 136

Mechanical Jacks 5 20 Ton Ratchet Jack 22B 85A 85A is used to lift a CNC machine for installation. Five ton lifting capacity, low toe height and light weight make the models 84A, 85A, & 86A universal tools. Ten ton models 1017 & A1022 are used extensively by structural movers, riggers & maintenance crews. 5 Ton Ratchet Jacks These units are all mechanically identical and vary only in stroke and height. 10 Ton Ratchet Jacks The 1017 and 22B incorporate a ductile iron housing for maximum durability. The A1022, which is identical to the 22B except for an aluminum housing, is the ideal choice when portability is important. These jacks are often selected for lifts of 10 tons or less because of their low handle effort. Supporting Cap. (Tons) Lifting Cap. (Tons) Stroke Handle Effort per Ton Cap Min. Steel Toe Min. Base Size 84A 5 5 7 32 14 1 3 /4 5 x 7 3 /8 28 85A 5 5 10 32 17 1 3 /4 5 x 7 3 /8 30 86A 5 5 13 32 20 1 3 /4 5 x 7 3 /8 35 1017 10 10 9 1 /2 30 17 1 /4 2 6 x 8 3 /4 40 A1022 10 10 12 30 21 5 /8 2 1 /4 6 1 /2 x 10 1 /4 42 22B 10 10 12 30 21 5 /8 2 1 /4 6 1 /2 x 10 1 /4 70 A1538 15 8 22 32 8 x 8 1 /4 62 24A 20 15 13 32 23 1 /4 2 1 /4 8 x 10 1 /4 93 2029 20 15 18 32 28 1 /4 2 1 /4 8 x 11 104 Pivot Bases are included on model A1538. Optional for the A1538 are I-Beam Base (#10800) and Chain (#10760). Order Number Lever Bars Length Diameter 10640 36 1 8 10665 60 1 1 /4 17 10675 72 1 1 /4 20 www.rentlgh.com Jacking Equipment 137

Mechanical Jacks 15 50 Ton Superjack Outdoor use and weld splatter can shorten the life of standard jacks. We chose Simplex Superjacks for the bullet proof construction and holding power. They provide trouble-free service in the roughest applications. Superjacks Rentals@RentLGH.com Jacking Equipment (Tons) Min. Stroke Handle Effort Per Ton Base Diameter A1510C 15 10 1 /4 5 9 5 1 /2 28 2510C 25 10 1 /4 5 6 5 1 /2 43 A2510C 25 10 1 /4 5 6 5 1 /2 34 A2515C 25 15 9 6 5 1 /2 43 3510D 35 10 1 /4 5 5 5 1 /2 44 A3510D 35 10 1 /4 5 5 5 1 /2 34 5010B 50 10 5 /16 4 4 7 1 /4 80 A5010B 50 10 5 /16 4 4 7 1 /4 61 Order Number Steel Lever Bars Length Diameter 10640 36 1 8 10660 56 1 1 /8 16 138

Air Bags 1.5 70 Ton Airbag & Accessories 202 Dual Controller 291 Single Controller Max Lifting Cap. (Tons) Lifting Ht. (Steel) (Kevlar) Max Working Pressure (p.s.i.) Dimensions Length Width Collapsed Ht. (Steel) (Kevlar) 1.5 2.0-101k 120 6 6.75 N/A 2 3.3 3.0-103k 120 12 6.75 N/A 3 6 4.5 106s 106k 120 10 10 1 6 4 13 7.5 113s 113k 120 15 15 1 15 11 22 9.5 122s 122k 120 20 20 1 28 22 32 12 132s 132k 120 21 25 1 35 28 50 15 150s 150k 120 29 29 1 63 45 70 18 170s 170k 120 34 34 1 81 60 All lifting capacities mentioned in the charts are measured at the maximum effective lifting area (A). As the air bag is inflated (B), this effective area decreases (C) due to the rounded shape of the air bag. Lifting capacity also decreases (see performance chart). Stack up two jacks together to increase effective lifting height. www.rentlgh.com Jacking Equipment 139

Hydraulic s 5 100 Ton Single-Acting, Spring Return RC256 RC506 Rentals@RentLGH.com Jacking Equipment Cap. Tons (Max) Stroke Effective Oil Cap. Area (in. 3 ) (in. 2 ) Collapsed A Extended B Outside Dia. D Bore Dia. E Plunger Dia. F Base to Adv. Port H Saddle Dia. J Saddle Protrusion from Plngr. K Collar Thread W Collar Thread Length X RC-50**.63.99.62 1.63 2.25 2.31 1.13 1.00.75 ** ** 2.2 RC-51 1.00.99.99 4.34 5.34 1.50 1.13 1.00.75 1.00.25 1 1 /2-16 1.13 2.3 RC-53 5 3.00.99 2.98 6.50 9.50 1.50 1.13 1.00.75 1.00.25 1 1 /2-16 1.13 3.3 RC-55* (4.9) 5.00.99 4.97 8.50 13.50 1.50 1.13 1.00.75 1.00.25 1 1 /2-16 1.13 4.1 RC-57 7.00.99 6.96 10.75 17.75 1.50 1.13 1.00.75 1.00.25 1 1 /2-16 1.13 5.3 RC-59 9.13.99 9.07 12.75 21.88 1.50 1.13 1.00.75 1.00.25 1 1 /2-16 1.13 6.1 RC-101 1.00 2.24 2.24 3.53 4.53 2.25 1.69 1.50.75 2 1 /4-14 1.06 4.0 RC-102* 2.13 2.24 4.75 4.78 6.91 2.25 1.69 1.50.75 1.38.25 2 1 /4-14 1.13 5.1 RC-104 4.13 2.24 9.23 6.75 10.88 2.25 1.69 1.50.75 1.38.25 2 1 /4-14 1.06 7.2 RC-106* 10 6.13 2.24 13.70 9.75 15.88 2.25 1.69 1.50.75 1.38.25 2 1 /4-14 1.13 9.8 RC-108 (11.2) 8.00 2.24 17.89 11.75 19.75 2.25 1.69 1.50.75 1.38.25 2 1 /4-14 1.06 12 RC-1010* 10.13 2.24 22.65 13.75 23.88 2.25 1.69 1.50.75 1.38.25 2 1 /4-14 1.13 14 RC-1012 12.00 2.24 26.84 15.75 27.75 2.25 1.69 1.50.75 1.38.25 2 1 /4-14 1.06 15 RC-1014 14.00 2.24 31.31 17.75 31.75 2.25 1.69 1.50.75 1.38.25 2 1 /4-14 1.06 18 RC-151 1.0 3.14 3.14 4.88 5.88 2.75 2.00 1.63.75 1.50.38 2 3 /4-16 1.19 7.2 RC-152 2.00 3.14 6.28 5.88 7.88 2.75 2.00 1.63.75 1.50.38 2 3 /4-16 1.19 9 RC-154* 4.00 3.14 12.57 7.88 11.88 2.75 2.00 1.63.75 1.50.38 2 3 /4-16 1.19 11 RC-156* 15 6.00 3.14 18.85 10.69 16.69 2.75 2.00 1.63 1.00 1.50.38 2 3 /4-16 1.19 15 RC-158 (15.7) 8.00 3.14 25.13 12.69 20.69 2.75 2.00 1.63 1.00 1.50.38 2 3 /4-16 1.19 18 RC-1510 10.00 3.14 31.42 14.69 24.69 2.75 2.00 1.63 1.00 1.50.38 2 3 /4-16 1.19 21 RC-1512 12.00 3.14 37.70 16.69 28.69 2.75 2.00 1.63 1.00 1.50.38 2 3 /4-16 1.19 24 RC-1514 14.00 3.14 43.98 18.69 32.69 2.75 2.00 1.63 1.00 1.50.38 2 3 /4-16 1.19 26 RC-251 1.00 5.16 5.16 5.50 6.50 3.38 2.56 2.25 1.00 2.00.41 3 5 /16-12 1.94 13 RC-252* 2.00 5.16 10.31 6.50 8.50 3.38 2.56 2.25 1.00 2.00.41 3 5 /16-12 1.94 14 RC-254* 4.00 5.16 20.63 8.50 12.50 3.38 2.56 2.25 1.00 2.00.41 3 5 /16-12 1.94 18 RC-256* 25 6.25 5.16 32.23 10.75 17.00 3.38 2.56 2.25 1.00 2.00.41 3 5 /16-12 1.94 22 RC-258 (25.8) 8.25 5.16 42.55 12.75 21.00 3.38 2.56 2.25 1.00 2.00.41 3 5 /16-12 1.94 27 RC-2510 10.25 5.16 52.86 14.75 25.00 3.38 2.56 2.25 1.00 2.00.41 3 5 /16-12 1.94 31 RC-2512 12.25 5.16 63.18 16.75 29.00 3.38 2.56 2.25 1.00 2.00.41 3 5 /16-12 1.94 36 RC-2514* 14.25 5.16 73.49 18.75 33.00 3.38 2.56 2.25 1.00 2.00.41 3 5 /16-12 1.94 39 RC-308 30 (32.4) 8.25 6.49 53.56 15.25 23.50 4.00 2.88 2.25 2.25 2.00.41 3 5 /16-12 1.94 40 RC-502 2.00 11.04 22.09 6.94 8.94 5.00 3.75 3.13 1.31 2.81.11 5-12 2.19 33 RC-504 50 4.00 11.04 44.18 8.94 12.94 5.00 3.75 3.13 1.31 2.81.11 5-12 2.19 42 RC-506* (55.2) 6.25 11.04 69.03 11.13 17.38 5.00 3.75 3.13 1.38 2.81.11 5-12 2.19 51 RC-5013 13.25 11.04 146.34 18.13 31.38 5.00 3.75 3.13 1.38 2.81.11 5-12 2.19 83 RC-756 75 6.13 15.90 97.41 11.25 17.38 5.75 4.50 3.75 1.19 2.81.23 5 3 /4-12 1.75 65 RC-7513 (79.5) 13.13 15.90 208.74 19.38 32.50 5.75 4.50 3.75 1.19 2.81.23 5 3 /4-12 1.75 130 RC-1006 6.63 20.63 136.67 14.06 20.69 7.00 5.13 4.13 1.63 2.81.11 6 100 (103.1) /8-12 1.75 130 RC-10010 10.25 20.63 211.45 17.69 27.94 7.00 5.13 4.13 1.63 2.81.11 6 7 /8-12 1.75 160 *Available as a set. **RC-50 cylinder has non-removable grooved saddle and no collar thread. ***D1=1.63 inch, L =.81 inch, M = 1.00 inch. 140

Hydraulic s 5 100 Ton Single-Acting, Spring Return, Low-Profile RCS302 RCS-Series RSM-Series RCS1002 Cap. Tons (Max) Stroke Effective Area (in 2 ) Oil Cap. (in 3 ) Collapsed A Extended B Outside Diameter D Bore Diameter E Plunger Diameter F Base to Advance Port H Plunger Protrusion from Base K Plunger to Base L Plunger to Mtg. Hole M 5 (4.9).25 RSM-50*.99.25 1.28 1.53 2.31 x 1.63 1.13 1.00.63.04.81.88 2.3 10 (11.2).44 RSM-100 2.24.98 1.69 2.13 3.25 x 2.19 1.69 1.50.75.04 1.09 1.34 3.1 20 (22.1).44 RSM-200 4.43 1.94 2.03 2.47 4.00 x 3.00 2.38 2.00.75.04 1.56 1.56 6.8 30 (32.4).50 RSM-300 6.49 3.25 2.31 2.81 4.63 x 3.75 2.88 2.50.75.08 1.88 1.75 10 50 (48.1).63 RSM-500 9.62 6.01 2.63 3.25 5.50 x 4.50 3.50 2.75.75.08 2.25 2.13 15 75 (79.5).63 RSM-750 15.90 9.94 3.13 3.75 6.50 x 5.50 4.50 3.25.75.08 2.75 2.63 25 100 (98.1).63 RSM-1000 19.63 12.27 3.38 4.00 7.00 x 6.00 5.00 3.63.75.08 3.00 2.94 32 150 (153.4).63 RSM-1500 30.68 19.17 3.94 4.56 8.50 x 7.50 6.25 4.50.94.08 3.75 3.25 58 10 (11.2) 1.50 RCS-101** 2.24 3.35 3.47 4.97 2.75 1.69 1.50.69.20 9 20 (22.1) 1.75 RCS-201** 4.43 7.75 3.88 5.63 3.63 2.38 2.00.69.13 11 30 (32.4) 2.44 RCS-302** 6.49 15.82 4.63 7.06 4.00 2.88 2.62.75.13 15 50 (48.1) 2.38 RCS-502** 9.62 22.85 4.81 7.19 4.88 3.50 2.75.94.08 24 100 (98.1) 2.25 RCS-1002** 19.63 44.18 5.56 7.81 6.50 5.00 3.63 1.25.06 50 * RSM-50 is fitted with an AR-400 coupler. ** Available as a set. www.rentlgh.com Jacking Equipment 141

Hydraulic s 60 600 Ton Single-Acting, Load Return, Pancake Lock Nut CLP Series Note: These cylinders have tilt saddles. Rentals@RentLGH.com Jacking Equipment Cap. Tons (Max) Stroke Effective Area (in 2 ) Oil Cap. (in 3 ) Collapsed A Extended B Outside Diameter D Bore Diameter E Plunger Diameter F (mm) Base to Advance Port H Saddle Diameter J Saddle Protrusion from Plunger K Saddle Max. Tilt Angle R Lock Nut S 60 (67.1) 1.97 CLP-602 13.42 26.42 4.92 6.89 5.51 4.13 Tr 104 x 4.75 3.78.24 5 1.10 33 100 (113.7) 1.97 CLP-1002 22.75 44.78 5.39 7.36 6.89 5.38 Tr 136 x 6.83 4.96.31 5 1.22 57 160 (179.2) 1.77 CLP-1602 35.85 63.51 5.83 7.60 8.66 6.76 Tr 171 x 6 1.06 6.30.35 5 1.57 97 200 (221.3) 1.77 CLP-2002 44.27 78.43 6.10 7.87 9.65 7.51 Tr 190 x 6 1.18 7.09.39 5 1.69 125 250 (284.2) 1.77 CLP-2502 56.85 100.72 6.26 8.03 10.83 8.51 Tr 216 x 6 1.26 7.87.43 5 1.73 163 400 (433.6) 1.77 CLP-4002 86.72 153.64 7.01 8.78 13.78 10.51 Tr 266 x 6 1.54 9.84.43 4 2.17 295 500 (566.2) 1.77 CLP-5002 113.25 200.63 7.56 9.33 15.75 12.01 Tr 305 x 6 1.89 11.42.39 3 2.44 416 600 2 CLP6002D101ID 1327 265 9.89 11.89 16.93 n/a n/a 2.07 12.20.45 3 2.70 630 142

Hydraulic s 50 1,000 Ton Single-Acting, Load Return, Lock Nut Optional Tilt Saddle CLL Series Cap. Stroke Tons (Max) 50 (59.1) 100 (102.9) 150 (153.9) 200 (206.1) 250 (284.0) 300 (353.6) 400 (433.9) 500 (566.3) 600 (662.9) 800 (911.6) 1000 (1136) Effective Oil Cap. Area (in 3 ) (in 2 ) Collapsed A Extended B Outside Dia. D Bore Dia. E Plunger Dia. F Base to Adv. Port H Stand. Saddle Diam. J Saddle Protrusion from Plgr. K Depth of Plunger Hole L Lock Nut S 1.97 CLL-502 10.99 21.63 6.46 8.43 4.92 3.74 Tr 95 x 4 1.18 2.80.08.51 1.42 35 3.94 CLL-504 10.99 43.25 8.43 12.36 4.92 3.74 Tr 95 x 4 1.18 2.80.08.51 1.42 46 5.91 CLL-506 10.99 64.88 10.39 16.30 4.92 3.74 Tr 95 x 4 1.18 2.80.08.51 1.42 57 7.87 CLL-508 10.99 86.51 12.36 20.24 4.92 3.74 Tr 95 x 4 1.18 2.80.08.51 1.42 68 9.84 CLL-5010 10.99 108.14 14.33 24.17 4.92 3.74 Tr 95 x 4 1.18 2.80.08.51 1.42 79 11.81 CLL-5012 10.99 129.76 16.30 28.11 4.92 3.74 Tr 95 x 4 1.18 2.80.08.51 1.42 90 1.97 CLL-1502 20.57 40.50 7.36 9.33 6.50 5.12 Tr 130 x 6 1.18 2.80.08.51 1.73 68 3.94 CLL-1004 20.57 81.00 9.33 13.27 6.50 5.12 Tr 130 x 6 1.18 2.80.08.51 1.73 87 5.91 CLL-1006 20.57 121.50 11.30 17.20 6.50 5.12 Tr 130 x 6 1.18 2.80.08.51 1.73 106 7.87 CLL-1008 20.57 162.00 13.27 21.14 6.50 5.12 Tr 130 x 6 1.18 2.80.08.51 1.73 125 9.84 CLL-10010 20.57 202.50 15.24 25.08 6.50 5.12 Tr 130 x 6 1.18 2.80.08.51 1.73 143 11.81 CLL-10012 20.57 242.99 17.20 29.02 6.50 5.12 Tr 130 x 6 1.18 2.80.08.51 1.73 162 1.97 CLL-1502 30.78 60.58 8.23 10.20 8.07 6.26 Tr 159 x 6 1.54 5.12.08.98 1.73 117 3.94 CLL-1504 30.78 121.17 10.20 14.13 8.07 6.26 Tr 159 x 6 1.54 5.12.08.98 1.73 146 5.91 CLL-1506 30.78 181.75 12.17 18.07 8.07 6.26 Tr 159 x 6 1.54 5.12.08.98 1.73 174 7.87 CLL-1508 30.78 242.33 14.13 22.01 8.07 6.26 Tr 159 x 6 1.54 5.12.08.98 1.73 203 9.84 CLL-15010 30.78 302.92 16.10 25.94 8.07 6.26 Tr 159 x 6 1.54 5.12.08.98 1.73 231 11.81 CLL-15012 30.78 363.50 18.07 29.88 8.07 6.26 Tr 159 x 6 1.54 5.12.08.98 1.73 260 1.97 CLL-2002 41.17 81.04 9.57 11.54 9.25 7.24 Tr 184 x 6 1.97 5.12.08.98 1.97 183 5.91 CLL-2006 41.17 243.13 13.50 19.41 9.25 7.24 Tr 184 x 6 1.97 5.12.08.98 1.97 260 11.81 CLL-20012 41.17 486.27 19.41 31.22 9.25 7.24 Tr 184 x 6 1.97 5.12.08.98 1.97 376 1.97 CLL-2502 56.75 111.70 9.80 11.77 10.83 8.50 Tr 216 x 6 1.97 5.91.08.98 2.20 256 5.91 CLL-2506 56.75 335.11 13.74 19.65 10.83 8.50 Tr 216 x 6 1.97 5.91.08.98 2.20 359 11.81 CLL-25012 56.75 670.22 19.65 31.46 10.83 8.50 Tr 216 x 6 1.97 5.91.08.98 2.20 515 1.97 CLL-3002 70.71 139.19 11.61 13.58 12.20 9.49 Tr 241 x 6 2.32 5.47.20.98 2.36 382 5.91 CLL-3006 70.71 417.56 15.55 21.46 12.20 9.49 Tr 241 x 6 2.32 5.47.20.98 2.36 514 11.81 CLL-30012 70.71 835.11 21.46 33.27 12.20 9.49 Tr 241 x 6 2.32 5.47.20.98 2.36 712 1.97 CLL-4002 86.79 170.84 13.19 15.16 13.78 10.51 Tr 266 x 6 2.76 6.26.20.98 2.76 553 5.91 CLL-4006 86.79 512.51 17.13 23.03 13.78 10.51 Tr 266 x 6 2.76 6.26.20.98 2.76 721 11.81 CLL-40012 86.79 1,025.02 23.03 34.84 13.78 10.51 Tr 266 x 6 2.76 6.26.20.98 2.76 972 1.97 CLL-5002 113.25 222.99 14.76 16.73 15.75 12.01 Tr 305 x 6 3.15 7.05.20.98 3.15 809 5.91 CLL-5006 113.25 668.77 18.70 24.61 15.75 12.01 Tr 305 x 6 3.15 7.05.20.98 3.15 1,029 11.81 CLL-50012 113.25 1337.55 24.61 36.42 15.75 12.01 Tr 305 x 6 3.15 7.05.20.98 3.15 1,360 1.97 CLL-6002 132.57 260.97 15.55 17.52 16.93 12.99 Tr 330 x 6 3.35 7.64.20.98 3.35 985 5.91 CLL-6006 132.57 782.90 19.49 25.39 16.93 12.99 Tr 330 x 6 3.35 7.64.20.98 3.35 1,241 11.81 CLL-60012 132.57 1,565.81 25.39 37.20 16.93 12.99 Tr 330 x 6 3.35 7.64.20.98 3.35 1,625 1.97 CLL-8002 182.42 359.09 17.91 19.88 19.88 15.24 Tr 387 x 6 3.94 8.82.20.98 3.94 1,565 5.91 CLL-8006 182.42 1,077.27 21.85 27.76 19.88 15.24 Tr 387 x 6 3.94 8.82.20.98 3.94 1,918 11.81 CLL-80012 182.42 2,154.55 27.76 39.57 19.88 15.24 Tr 387 x 6 3.94 8.82.20.98 3.94 2,446 1.97 CLL-10002 227.30 447.43 19.49 21.46 22.05 17.01 Tr 432 x 6 4.33 9.80.20.98 4.33 2,094 5.91 CLL-10006 227.30 1,342.30 23.43 29.33 22.05 17.01 Tr 432 x 6 4.33 9.80.20.98 4.33 2,517 11.81 CLL-100012 227.30 2,684.59 29.33 41.14 22.05 17.01 Tr 432 x 6 4.33 9.80.20.98 4.33 3,151 CLL-50 to CLL-250 CLL-300 to CLL-1000 www.rentlgh.com Jacking Equipment 143

Hydraulic s 30 150 Ton Double-Acting, Center Hole RRH Series Double-acting hollow plunger Rentals@RentLGH.com Jacking Equipment 30 60 Stroke Max Effective Area (in. 2 ) Oil (in. 3 ) Advance Retract Advance Retract Advance Retract 7.00 RRH-307 36 24 7.22 4.71 50.55 32.99 10.13 RRH-3010 36 24 7.22 4.71 73.12 47.71 3.50 RRH-603 64 42 12.73 8.37 44.57 29.21 6.50 RRH-606 64 42 12.73 8.37 82.77 54.24 10.12 RRH-6010 64 42 12.73 8.37 128.94 84.49 1.50 RRH-1001 103 68 20.63 13.54 30.94 20.32 100 3.00 RRH-1003 103 68 20.63 13.54 61.88 40.64 6.00 RRH-1006 103 68 20.63 13.54 123.76 81.29 10.13 RRH-10010 103 68 20.63 13.54 208.84 137.17 150 8.00 RRH-1508 158 80 31.62 15.91 252.97 127.23 30 60 100 Collapsed A Extended B Out. Dia. D Bore Dia. E Plunger Diam. F Cyl. Base to Adv. Port H Cyl. Top to Return Port I Saddle Diam. J Saddle Protrusion from Plngr. K Plunger Thread Length P Collar Thread W Collar Thread Length X Center Hole Diam. Y 13.00 20.00 4.50 3.50 2.50 1.00 2.38 2.50.38.88 4 1 /2 12 1.66 1.31 48 17.00 27.13 4.50 3.50 2.50 1.00 2.38 2.50.38.88 4 1 /2 12 1.66 1.31 60 9.75 13.25 6.25 4.88 3.63 1.25 2.63 3.61.50.75 6 1 /4 12 1.91 2.13 62 12.75 19.25 6.25 4.88 3.63 1.25 2.63 3.61.50.75 6 1 /4 12 1.91 2.13 78 17.25 27.38 6.25 4.88 3.63 1.25 2.63 3.61.50.75 6 1 /4 12 1.91 2.13 101 6.50 8.00 8.38 6.50 5.00 1.50 1.75 4.97.50 1.00 3.13 85 10.00 13.00 8.38 6.50 5.00 1.50 3.38 4.97.50 1.00 8 3 /8 12 2.38 3.13 135 13.50 19.50 8.38 6.50 5.00 1.50 3.38 4.97.50 1.00 8 3 /8 12 2.38 3.13 175 18.13 28.25 8.38 6.50 5.00 1.50 3.38 4.97.50 1.00 8 3 /8 12 2.38 3.13 235 150 13.75 21.75 9.75 7.50 6.00 1.50 2.38 5.00.19 1.00 3.13 245 144

Hydraulic s 150 500 Ton Double-Acting capacity Stroke Cyl. effect Area (in. 2 ) Oil Cap (in. 3 ) Collap. A Ext. B Outside Diam D Cyl. Bore Diam E Plngr. Diam. F Cyl. Base to Advance port H 2.25 RR-1502 30.71 69.11 7.19 9.44 8.00 6.25 4.50.88 3.67.06 - - - - 2.63 110 150 6.13 RR1506 30.71 188 15.19 21.31 8.00 6.25 4.50 1.94 4.49.75 3 3 /8 1.38 8 2.36 3.31 205 13.13 RR15013 30.71 403 22.20 35.31 8.00 6.25 4.50 1.94 4.49.75 3 3 /8 1.38 8 2.36 3.31 275 32.13 RR-15032 30.71 986 43.94 76.06 8.00 6.25 4.50 3.00 4.49.75 3 3 /8 1.38 8 2.36 3.50 525 6.00 RR-2006 44.21 265 16.94 22.94 9.75 7.50 5.25 2.25 5.25.88 - - - - 3.81 325 13.00 RR-20013 44.21 574 23.94 36.94 9.75 7.50 5.25 2.25 5.25.88 2.5 2.50 9 3 /4 2.13 3.81 440 200 18.00 RR-20018 44.21 795 30.13 48.13 9.75 7.50 5.25 3.38 5.25.88 2.5 2.50 9 3 /4 2.13 4.00 450 24.00 RR-20024 44.21 1,061 36.13 60.13 9.75 7.50 5.25 3.38 5.25.88 2.5 2.50 9 3 /4 2.13 4.00 616 36.00 RR-20036 44.21 1,592 48.13 84.13 9.75 7.50 5.25 3.38 5.25.88 2.5 2.50 9 3 /4 2.13 4.00 845 48.00 RR-20048 44.21 2,122 60.13 108.13 9.75 7.50 5.25 3.38 5.25.88 2.5 2.50 9 3 /4 2.13 4.00 1,065 6.00 RR-3006 70.93 426 19.13 25.13 12.25 9.50 6.50 3.50 6.50 1.13 2.5 3.25 12 1 /4 2.31 4.50 441 12.00 RR-30012 70.93 851 25.13 37.13 12.25 9.50 6.50 3.50 6.50 1.13 2.5 3.25 12 1 /4 2.31 4.50 608 300 18.00 RR-30018 70.93 1,277 31.13 49.13 12.25 9.50 6.50 3.50 6.50 1.13 2.5 3.25 12 1 /4 2.31 4.50 776 24.00 RR-30024 70.93 1,702 37.13 61.13 12.25 9.50 6.50 3.50 6.50 1.13 2.5 3.25 12 1 /4 2.31 4.50 1,034 36.00 RR-30036 70.93 2,553 49.13 85.13 12.25 9.50 6.50 3.50 6.50 1.13 2.5 3.25 12 1 /4 2.31 4.50 1,385 48.00 RR-30048 70.93 3,405 61.13 109.1 12.25 9.50 6.50 3.50 6.50 1.13 2.5 3.25 12 1 /4 2.31 4.50 1720 6.00 RR-4006 95.09 571 21.19 27.19 14.13 11.00 7.50 4.25 7.50 1.13 3 3.75 14 1 /8 2.56 5.25 670 12.00 RR-40013 95.09 1,141 27.19 39.19 14.13 11.00 7.50 4.25 7.50 1.13 3 3.75 14 1 /8 2.56 5.25 880 400 18.00 RR-40018 95.09 1,712 33.19 51.19 14.13 11.00 7.50 4.25 7.50 1.13 3 3.75 14 1 /8 2.56 5.25 1,000 24.00 RR-40024 95.09 2,282 39.19 63.19 14.13 11.00 7.50 4.25 7.50 1.13 3 3.75 14 1 /8 2.56 5.25 1,317 36.00 RR-40036 95.09 3,423 51.19 87.19 14.13 11.00 7.50 4.25 7.50 1.13 3 3.75 14 1 /8 2.56 5.25 1,746 48.00 RR-40048 95.09 4,564 63.19 111.2 14.13 11.00 7.50 4.25 7.50 1.13 3 3.75 14 1 /8 2.56 5.25 2,162 6.00 RR-5006 113.15 679 22.75 28.75 15.63 12.00 8.00 4.75 8.00 1.13 3 1 /4 4.25 15 5 /8 3.13 6.00 953 12.00 RR-50012 113.15 1,358 28.75 40.75 15.63 12.00 8.00 4.75 8.00 1.13 3 1 /4 4.25 15 5 /8 3.13 6.00 1,300 500 18.00 RR-50018 113.15 2,037 34.75 52.75 15.63 12.00 8.00 4.75 8.00 1.13 3 1 /4 4.25 15 5 /8 3.13 6.00 1,500 24.00 RR-50024 113.15 2,716 40.75 64.75 15.63 12.00 8.00 4.75 8.00 1.13 3 1 /4 4.25 15 5 /8 3.13 6.00 1,800 36.00 RR-50036 113.15 4,074 52.75 88.75 15.63 12.00 8.00 4.75 8.00 1.13 3 1 /4 4.25 15 5 /8 3.13 6.00 2,210 48.00 RR-50048 113.15 5,431 64.75 112.8 15.63 12.00 8.00 4.75 8.00 1.13 3 1 /4 4.25 15 5 /8 3.13 6.00 2,700 Stroke Maximum Operating Pressure Number (psi) Maximum Effective Area Oil Push Pull Push Pull Push Pull 500 4.00 10,000 CLR-5004 500 193 113.5 38.60 445.5 152 791 Collapse A Extend B Outside Dia. D Bore Dia. E Plunger Dia. F Base to Advance Port H Top to Retract Port I Standard Saddle Dia. J Saddle Protr. from Plgr. K Depth of Plunger Hole L 15.75 19.75 15.75 12.01 9.76 3.15 6.61 7.05.20.98 Saddle Diam. J Saddle Protrusion from plngr K Plunger Internal Thread O Plunger Thread Length P Collar Thread W Collar Thread Length X Top to Return Port www.rentlgh.com Jacking Equipment 145

Hydraulic s 50 200 Ton Double-Acting Rentals@RentLGH.com Jacking Equipment Stroke capacity 50 100 150 200 Number Maximum Effective Area (in. 2 ) Oil (in. 3 ) Collap. A Ext. B Outside Diam. D Cyl. Bore Diam. E Plunger Diam. F Base Mounting Hole Dimensions / (ton) Base to Advance Port H Top to Retract Port I Bolt Circle U Standard Saddle Diam. J Saddle Protrusion from Plngr K Thread Size V (mm) Depth of Plunger Hole L Push Pull Push Pull Push Pull 1.97 CLRG-502 59.1 29 11.81 5.85 23.25 11.51 6.38 8.35 5.12 3.88 2.76 1.65 1.29 1.97.04.75 37 3.94 CLRG-504 59.1 29 11.81 5.85 46.50 23.02 8.35 12.28 5.12 3.88 2.76 1.65 1.29 1.97.04.75 44 5.91 CLRG-506 59.1 29 11.81 5.85 69.75 34.52 10.31 16.22 5.12 3.88 2.76 1.65 1.29 1.97.04.75 51 7.87 CLRG-508 59.1 29 11.81 5.85 93.00 46.03 12.28 20.16 5.12 3.88 2.76 1.65 1.29 1.97.04.75 60 9.84 CLRG-5010 59.1 29 11.81 5.85 116.25 57.54 14.25 24.09 5.12 3.88 2.76 1.65 1.29 1.97.04.75 68 11.81 CLRG-5012 59.1 29 11.81 5.85 139.50 69.05 16.22 28.03 5.12 3.88 2.76 1.65 1.29 1.97.04.75 75 1.97 CLRG-1002 102.9 48 20.57 9.59 40.50 18.87 7.16 9.13 6.50 5.12 3.74 2.13 1.89 2.95.04.75 42 3.94 CLRG-1004 102.9 48 20.57 9.59 81.00 37.74 9.13 13.06 6.50 5.12 3.74 2.13 1.89 2.95.04.75 64 5.91 CLRG-1006 102.9 48 20.57 9.59 121.50 56.61 11.09 17.00 6.50 5.12 3.74 2.13 1.89 2.95.04.75 88 7.87 CLRG-1008 102.9 48 20.57 9.59 162.00 75.49 13.06 20.94 6.50 5.12 3.74 2.13 1.89 2.95.04.75 110 9.84 CLRG-10010 102.9 48 20.57 9.59 202.50 94.36 15.03 24.87 6.50 5.12 3.74 2.13 1.89 2.95.04.75 134 11.81 CLRG-10012 102.9 48 20.57 9.59 242.99 113.23 17.00 28.81 6.50 5.12 3.74 2.13 1.89 2.95.04.75 157 1.97 CLRG-1502 153.9 75 30.78 14.96 60.58 29.44 7.72 9.69 8.07 6.26 4.49 2.40 2.22 3.70.04.75 86 3.94 CLRG-1504 153.9 75 30.78 14.96 121.17 58.88 9.69 13.62 8.07 6.26 4.49 2.40 2.22 3.70.04.75 115 5.91 CLRG-1506 153.9 75 30.78 14.96 181.75 88.32 11.65 17.56 8.07 6.26 4.49 2.40 2.22 3.70.04.75 143 7.87 CLRG-1508 153.9 75 30.78 14.96 242.33 117.76 13.62 21.50 8.07 6.26 4.49 2.40 2.22 3.70.04.75 172 9.84 CLRG-15010 153.9 75 30.78 14.96 302.92 147.20 15.59 25.43 8.07 6.26 4.49 2.40 2.22 3.70.04.75 203 11.81 CLRG-15012 153.9 75 30.78 14.96 363.50 176.64 17.56 29.37 8.07 6.26 4.49 2.40 2.22 3.70.04.75 231 1.97 CLRG-2002 206.1 98 41.22 19.68 81.13 38.74 8.50 10.47 9.25 7.24 5.24 2.62 2.22 4.45.04.94 121 5.91 CLRG-2006 206.1 98 41.22 19.68 243.40 116.23 12.44 18.35 9.25 7.24 5.24 2.62 2.22 4.45.04.94 201 11.81 CLRG-20012 206.1 98 41.22 19.68 486.79 232.46 18.35 30.16 9.25 7.24 5.24 2.62 2.22 4.45.04.94 322 Minimum Thread Depth Z CLRG-50 2.56 M12.87 CLRG-100 3.74 M12.87 CLRG-150 5.12 M12.87 CLRG-200 6.50 M12.87 CLRG-250 7.48 M12 1.42 CLRG-300 7.09 M16 1.42 CLRG-400 8.07 M16 1.50 CLRG-500 9.84 M24 1.50 CLRG-600 10.83 M24 1.50 CLRG-800 12.99 M24 1.50 CLRG-1000 14.76 M24 1.50 146

Hydraulic s 50 300 Ton Single-Acting, Load Return capacity 50 100 150 200 250 300 Stroke Cyl. effect Area (in2) Oil Cap (in3) Collap. A Ext. B Outside Diam D Cyl. Bore Diam E Plngr. Diam. F Cyl. Base to Advance port H Saddle Diam. J Saddle Protrusion from plngr K Depth of Plunger Hole L Base Mounting Holes 1.97 CLSG-502 11.81 23.25 6.38 8.35 5.12 3.88 2.76 2.05 1.97.04.75 2.56 M12.87 37 3.94 CLSG-504 11.81 46.50 8.35 12.28 5.12 3.88 2.76 2.05 1.97.04.75 2.56 M12.87 44 5.91 CLSG-506 11.81 69.75 10.31 16.22 5.12 3.88 2.76 2.05 1.97.04.75 2.56 M12.87 51 7.87 CLSG-508 11.81 93.00 12.28 20.16 5.12 3.88 2.76 2.05 1.97.04.75 2.56 M12.87 60 9.84 CLSG-5010 11.81 116.30 14.25 24.09 5.12 3.88 2.76 2.05 1.97.04.75 2.56 M12.87 68 11.81 CLSG-5012 11.81 139.50 16.22 28.03 5.12 3.88 2.76 2.05 1.97.04.75 2.56 M12.87 75 1.97 CLSG-1002 20.57 40.50 7.16 9.13 6.50 5.12 3.74 2.13 2.95.04.75 3.74 M12.87 42 3.94 CLSG-1004 20.57 81.00 9.13 13.06 6.50 5.12 3.74 2.13 2.95.04.75 3.74 M12.87 64 5.91 CLSG-1006 20.57 121.50 11.09 17.00 6.50 5.12 3.74 2.13 2.95.04.75 3.74 M12.87 88 7.87 CLSG-1008 20.57 162.00 13.06 20.94 6.50 5.12 3.74 2.13 2.95.04.75 3.74 M12.87 110 9.84 CLSG-10010 20.57 202.50 15.03 24.87 6.50 5.12 3.74 2.13 2.95.04.75 3.74 M12.87 134 11.81 CLSG-10012 20.57 243.00 17.00 28.81 6.50 5.12 3.74 2.13 2.95.04.75 3.74 M12.87 157 1.97 CLSG-1502 30.78 60.60 7.72 9.69 8.07 6.26 4.49 2.40 3.70.04.75 5.12 M12.87 86 3.94 CLSG-1504 30.78 121.20 9.69 13.62 8.07 6.26 4.49 2.40 3.70.04.75 5.12 M12.87 115 5.91 CLSG-1506 30.78 181.70 11.65 17.56 8.07 6.26 4.49 2.40 3.70.04.75 5.12 M12.87 143 7.87 CLSG-1508 30.78 242.30 13.62 21.50 8.07 6.26 4.49 2.40 3.70.04.75 5.12 M12.87 172 9.84 CLSG-15010 30.78 302.90 15.59 25.43 8.07 6.26 4.49 2.40 3.70.04.75 5.12 M12.87 203 11.81 CLSG-15012 30.78 363.50 17.56 29.37 8.07 6.26 4.49 2.40 3.70.04.75 5.12 M12.87 231 1.97 CLSG-2002 41.22 81.13 8.50 10.47 9.25 7.24 5.24 2.62 4.45.04.94 6.50 M12.87 121 5.91 CLSG-2006 41.22 243.40 12.44 18.35 9.25 7.24 5.24 2.62 4.45.04.94 6.50 M12.87 201 11.81 CLSG-20012 41.22 486.80 18.35 30.16 9.25 7.24 5.24 2.62 4.45.04.94 6.50 M12.87 322 1.97 CLSG-2502 56.80 111.80 9.25 11.22 10.83 8.50 6.50 2.87 5.71.04.94 7.48 M12.87 196 5.91 CLSG-2506 56.80 335.40 13.19 19.09 10.83 8.50 6.50 2.87 5.71.04.94 7.48 M12.87 300 11.81 CLSG-25012 56.80 670.80 19.09 30.91 10.83 8.50 6.50 2.87 5.71.04.94 7.48 M12.87 456 1.97 CLSG-3002 70.71 139.20 12.28 14.25 12.20 9.49 7.76 3.98 6.97.04.75 7.09 M16 1.42 406 5.91 CLSG-3006 70.71 417.50 16.22 22.13 12.20 9.49 7.76 3.98 6.97.04.75 7.09 M16 1.42 511 11.81 CLSG-30012 70.71 835.10 22.13 12.20 12.20 9.49 7.76 3.98 6.97.04.75 7.09 M16 1.42 688 Bolt Cir. Diam U Thread V Thread Depth X www.rentlgh.com Jacking Equipment 147

Hydraulic s 400 1000 Ton Single-Acting, Load Return Optional Tilt Saddle Rentals@RentLGH.com Jacking Equipment 400 500 600 800 1000 Stroke Cyl. Effect Area (in. 2 ) Oil Cap (in. 3 ) Collap. A Ext. B Outside Diam D Cyl. Bore Diam E Plngr. Diam. F Cyl. Base to Advance Port H Saddle Diam. J J1 Saddle Protrusion from Plngr K K1 Depth of Plunger Hole L Base Mounting Holes 1.97 CLSG-4002 86.78 170.80 14.74 16.71 13.78 10.51 8.50 4.49 7.72 n/a.12 n/a 1.06 8.07 M16 1.42 595 5.91 CLSG-4006 86.78 512.50 18.68 24.59 13.78 10.51 8.50 4.49 7.72 7.59.12 2.00 1.06 8.07 M16 1.42 728 11.81 CLSG-40012 86.78 1,025.00 24.59 36.40 13.78 10.51 8.50 4.49 7.72 n/a.12 n/a 1.06 8.07 M16 1.42 928 1.97 CLSG-5002 113.25 222.90 16.50 18.46 15.75 12.01 9.76 4.49 8.98 n/a.12 n/a 1.06 9.84 M24 1.42 884 5.91 CLSG-5006 113.25 668.70 20.43 26.34 15.75 12.01 9.76 4.49 8.98 n/a.12 n/a 1.06 9.84 M24 1.42 1,058 11.81 CLSG-50012 113.25 1,337.00 26.34 37.15 15.75 12.01 9.76 4.49 8.98 n/a.12 n/a 1.06 9.84 M24 1.42 1,321 1.97 CLSG-6002 132.57 260.90 16.89 18.86 16.93 12.99 10.51 4.49 9.72 n/a.12 n/a 1.06 10.83 M24 1.50 1,045 5.91 CLSG-6006 132.57 782.90 20.83 26.73 16.93 12.99 10.51 4.49 9.72 n/a.12 n/a 1.06 10.83 M24 1.50 1,246 11.81 CLSG-60012 132.57 1,565.00 26.73 38.54 16.93 12.99 10.51 4.49 9.72 n/a.12 n/a 1.06 10.83 M24 1.50 1,545 1.97 CLSG-8002 182.32 358.90 18.66 20.63 19.88 15.24 12.48 5.87 11.69 n/a.12 n/a 1.06 12.99 M24 1.50 1,634 5.91 CLSG-8006 182.32 1,076.00 22.60 28.50 19.88 15.24 12.48 5.87 11.69 n/a.12 n/a 1.06 12.99 M24 1.50 1,914 11.81 CLSG-80012 182.32 2,153.00 28.50 40.31 19.88 15.24 12.48 5.87 11.69 n/a.12 n/a 1.06 12.99 M24 1.50 2,332 1.97 CLSG-1002 227.19 447.20 22.20 24.17 22.05 17.01 13.50 6.85 12.72 n/a.12 n/a 1.06 14.76 M24 1.50 2,341 5.91 CLSG-1006 227.19 1,341.00 26.14 32.05 22.05 17.01 13.50 6.85 12.72 n/a.12 n/a 1.06 14.76 M24 1.50 2,674 11.81 CLSG-100012 227.19 2,683.00 32.05 43.86 22.05 17.01 13.50 6.85 12.72 n/a.12 n/a 1.06 14.76 M24 1.50 3,172 Bolt Cir. Diam U Thread V Thread Depth X 148

Hydraulic s 12 100 Ton Single-Acting, Spring Return, Center Hole Stroke capacity 12 [13.8] 12 [13.8] 12 [13.8] 12 [13.8] 20 [23.6] 20 [23.6] 30 [36.1] 30 [36.1] 60 [63.6] 60 [63.6] Cyl. effect Area (in2) Oil Cap (in3) Collap. A Ext. B Outside Diam D Cyl. Bore Diam E Plngr. Diam. F Cyl. Base to Advance port H Saddle Diam. J Saddle Protrusion from plngr K Plunger Internal Thread O Plunger Thread Length P Collar Thread W Collar Thread Length X Top to Return Port 0.31 RCH-120 2.76 0.86 2.19 2.50 2.75 2.13 1.38.38 - - 3/4.63 2 3 /4 1.19.77 3.2 1.63 RCH-121 2.76 4.49 4.75 6.38 2.75 2.13 1.38.75 - - - - 2 3 /4 1.19.77 6.2 1.63 RCH-1211 2.76 4.49 4.75 6.38 2.75 2.13 1.38.75 - - 3/4.63 2 3 /4 1.19.77 6.2 3.00 RCH-123 2.76 8.29 7.25 10.25 2.75 2.13 1.38.75 - - - - 2 3 /4 1.19.77 9.8 2.00 RCH-202 4.73 9.46 6.38 8.38 3.88 2.88 2.13.75 2.13.27 1 9 /16.75 3 7 /8 1.50 1.06 17 6.10 RCH-206 4.73 28.67 12.05 18.11 3.88 2.88 2.13.75 2.13.27 1 9 /16.75 3 7 /8 1.50 1.06 31 2.50 RCH-302 7.22 18.05 7.03 9.53 4.50 3.50 2.50.85 2.50.38 1 13 /16.88 4 1 /2 1.66 1.31 24 6.13 RCH-306 7.22 44.23 13.00 19.13 4.50 3.50 2.50 1.00 2.50.38 1 13 /16.88 4 1 /2 1.66 1.31 48 3.00 RCH-603 12.73 38.20 9.75 12.75 6.25 4.88 3.63 1.25 3.61.50 2 3 /4.75 6 1 /4 1.91 2.12 62 6.00 RCH-606 12.73 76.41 12.75 18.75 6.25 4.88 3.63 1.25 3.61.50 2 3 /4.75 6 1 /4 1.91 2.12 78 100 [103] 3.00 RCH-1003 20.63 61.88 10.00 13.00 8.38 6.00 5.00 1.50 4.97.50 4 1.00 8 3 /8 2.38 3.11 132 www.rentlgh.com Jacking Equipment 149

A - Minimum Ht. B - Extended Ht. Hydraulic s 5 10 Ton Single-Acting, Spring Return Spring Return s Base Mounting Holes 5 Ton (except R-50) 1/4-20 UNC-2B THD On a 1.00 Dia B.C.,.56" dp. D F 10 Ton (except R101) 5/16-18 UNC-2B THD. On a 1.56 Dia. B.C.,.50" dp. G C See page 17 for R50 mounting dimensions. E Rentals@RentLGH.com Jacking Equipment Cap. Stroke Oil Cap. Req d (cu. in.) Ram Bore Dia. Effect Area (sq. in.) Pres. @ Cap. (psi) A B C D E F G Piston Piston Body Piston Base to Collar Min. Ht. Ext. Ht. I.D. Thrds O.D. O.D. Port C/L Thrds Thrds Depth R50 5 5/8.6 1 1 /8 1 10,000 1 5 /8 2 1 /4 2 9 /16 1 3/4 ---- ---- ---- ---- 2.5 P41 R51 5 1 1 /8.99 1 1 /8 1 10,000 4 3 /8 5 5 /16 1 1 /2 1.0 3/4 3/4 --16 3/4 1 1 /2 -- 16 1 1 /8 2.3 P41 R53 5 3 1 /8 2.98 1 1 /8 1 10,000 6 35 /64 9 1 /2 1 1 /2 1.0 3/4 3/4 --16 3/4 1 1 /2 -- 16 1 1 /8 3.3 P41 R55 5 5 1 /4 4.97 1 1 /8 1 10,000 8 35 /64 13 5 /8 1 1 /2 1.0 3/4 3/4 --16 3/4 1 1 /2 -- 16 1 1 /8 4.1 P42 R57 5 7 1 /8 6.96 1 1 /8 1 10,000 10 25 /32 17 23 /32 1 1 /2 1.0 3/4 3/4 --16 3/4 1 1 /2 -- 16 1 1 /8 5.3 P42 R59 5 9 1 /8 9.07 1 1 /8 1 10,000 12 25 /32 21 23 /32 1 1 /2 1.0 3/4 3/4 --16 3/4 1 1 /2 -- 16 1 1 /8 6.1 P42 R101 10 1 1 /16 2.3 1 11 /16 2 1 /4 8,945 3 21 /32 4 19 /32 2 1 /4 1 1 /2 3/4 ---- ---- 2 1 /4 -- 14 1 1 /8 4 P42 R102 10 2 1 /8 4.18 1 11 /16 2 1 /4 8,945 5 1 /32 6 29 /32 2 1 /4 1 1 /2 3/4 1 -- 8 3/4 2 1 /4 -- 14 1 1 /8 5.1 P42 R104 10 4 1 /8 9.2 1 11 /16 2 1 /4 8,945 6 45 /64 10 23 /32 2 1 /4 1 1 /2 3/4 1 -- 8 3/4 2 1 /4 -- 14 1 1 /8 7.2 P42 R106 10 6.0 13.7 1 11 /16 2 1 /4 8,929 9 25 /32 15 19 /32 2 1 /4 1 1 /2 3/4 1 -- 8 3/4 2 1 /4 -- 14 1 1 /8 9.8 P42 R108 10 8.0 17.89 1 11 /16 2 1 /4 8,929 11 25 /32 19 19 /32 2 1 /4 1 1 /2 3/4 1 -- 8 3/4 2 1 /4 -- 14 1 1 /16 12 P42 R1010 10 10.0 22.65 1 11 /16 2 1 /4 8,929 13 25 /32 23 19 /32 2 1 /4 1 1 /2 3/4 1 -- 8 3/4 2 1 /4 -- 14 1 1 /8 14 P42 R1012 10 12.0 26.84 1 11 /16 2 1 /4 8,929 15 19 /32 27 19 /32 2 1 /4 1 1 /2 3/4 1 -- 8 3/4 2 1 /4 -- 14 1 1 /16 15 P42 R1014 10 14.0 31.31 1 11 /16 2 1 /4 8,929 17 25 /32 31 19 /32 2 1 /4 1 1 /2 3/4 1 -- 8 3/4 2 1 /4 -- 14 1 1 /16 18 P42 Collar Thru Lgth Wgt. Sugstd. Hand Pump 150

Hydraulic s 15 25 Ton Single-Acting, Spring Return Spring Return s Large steel coils that were damaged in handling are reshaped using a Simplex R256 cylinder and PE70 Series pump. Cap. Stroke Oil Cap. Req d (cu. in.) Ram Bore Dia. Effect Area (sq. in.) Pres. @ Cap. (psi) A B C D E F G Piston Body Piston Base to Piston I.D. Min. Ht. Ext. Ht. Thrds Collar Thrds O.D. O.D. Port C/L Thrds Depth R152 15 2 1 /8 6.28 2.0 3 9 /64 9,554 5 53 /64 7 19 /32 2 3 /4 1 5 /8 3/4 1 -- 8 1 2 3 /4 -- 16 1 3 /16 9 P42 R154 15 4 1 /8 12.57 2.0 3 9 /64 9,554 7 53 /64 11 45 /64 2 3 /4 1 5 /8 3/4 1 -- 8 1 2 3 /4 -- 16 1 3 /16 11 P42 R156 15 6 3 /8 19.0 2.0 3 9 /64 9,554 11 1 /32 17 5 /32 2 3 /4 1 5 /8 1 1 -- 8 1 2 3 /4 -- 16 1 3 /16 15 P42 R1510 15 10 3 /8 31.4 2.0 3 9 /64 9,554 15 1 /32 25 5 /32 2 3 /4 1 5 /8 1 1 -- 8 1 2 3 /4 -- 16 1 3 /16 21 P140 R1514 15 14 3 /8 44.0 2.0 3 9 /64 9,554 19 1 /32 33 5 /32 2 3 /4 1 5 /8 1 1 -- 8 1 2 3 /4 -- 16 1 3 /16 26 P140 R251 25 1.0 5.16 2 9 /16 5 5 /32 9,690 5 15 /32 6 7 /32 3 1 /2 1 5 /8 1 1 1 /2 -- 16 1 1 /8 3 5 /16 -- 12 1 15 /16 13 P42 R252 25 2.0 10.31 2 9 /16 5 5 /32 9,690 6 15 /32 8 7 /32 3 1 /2 1 5 /8 1 1 1 /2 -- 16 1 1 /8 3 5 /16 -- 12 1 15 /16 14 P42 R254 25 4.0 20.63 2 9 /16 5 5 /32 9,690 8 15 /32 12 7 /32 3 1 /2 1 5 /8 1 1 1 /2 -- 16 1 1 /8 3 5 /16 -- 12 1 15 /16 18 P42 R256 25 6 1 /4 32.23 2 9 /16 5 5 /32 9,690 10 47 /64 16 47 /64 3 1 /2 1 5 /8 1 1 1 /2 -- 16 1 1 /8 3 5 /16 -- 12 1 15 /16 22 P42 R258 25 8 1 /4 42.55 2 9 /16 5 5 /32 9,690 12 47 /64 20 47 /64 3 1 /2 1 5 /8 1 1 1 /2 -- 16 1 1 /8 3 5 /16 -- 12 1 15 /16 27 P140 R2510 25 10 1 /4 52.86 2 9 /16 5 5 /32 9,690 14 47 /64 24 47 /64 3 1 /2 1 5 /8 1 1 1 /2 -- 16 1 1 /8 3 5 /16 -- 12 1 15 /16 31 P140 R2512 25 12 1 /4 63.18 2 9 /16 5 5 /32 9,690 16 47 /64 28 47 /64 3 1 /2 1 5 /8 1 1 1 /2 -- 16 1 1 /8 3 5 /16 -- 12 1 15 /16 36 P140 R2514 25 14 1 /4 73.49 2 9 /16 5 5 /32 9,690 18 47 /64 32 47 /64 3 1 /2 1 5 /8 1 1 1 /2 -- 16 1 1 /8 3 5 /16 -- 12 1 15 /16 39 P140 Collar Thru Lgth Wgt. Sugstd. Hand Pump www.rentlgh.com Jacking Equipment 151

Hydraulic s 30 100 Ton Single-Acting, Spring Return Spring Return s Contractors called on the brute force of Simplex R5513 cylinders to lift and position highway ramps in San Diego. G6 provided the power and control in this rough outdoor application. Rentals@RentLGH.com Jacking Equipment Cap. Stroke Oil Cap. Req d (cu. in.) Ram Bore Dia. Effect Area (sq. in.) Pres. @ Cap. (psi) A B C D E F G Piston Body Piston Base to Piston I.D. Collar Min. Ht. Ext. Ht. Thrds O.D. O.D. Port C/L Thrds Thrds Depth R308 30 8 1 /4 53.6 2 7 /8 6 1 /2 9,245 15 1 /4 23 1 /2 4 2 1 /4 2 1 /4 1 1 /2 -- 16 1 3 5 /16 --12 1 15 /16 40 P82A R552 55 2.0 22.08 3 3 /4 11 1 /32 9,960 6 15 /16 8 13 /16 5 3 5 /8 1 3 /8 ---- ---- 5 -- 12 2 13 /16 33 P42 R554 55 4.0 44.16 3 3 /4 11 1 /32 9,960 8 15 /16 12 13 /16 5 3 1 /8 1 3 /8 ---- ---- 5 -- 12 2 13 /16 42 P82A R556 55 6 1 /4 69.0 3 3 /4 11 1 /32 9,960 11 1 /8 17 1 /4 5 3 1 /8 1 3 /8 ---- ---- 5 -- 12 2 13 /16 51 R5513 55 13 1 /4 146.34 3 3 /4 11 1 /32 9,960 18 1 /4 31 3 /8 5 3 1 /8 1 3 /8 ---- ---- 5 -- 12 2 13 /16 83 R756 75 6.0 95.4 4 1 /2 16 9,430 11 5 /8 17 3 /8 5 3 /4 3 3 /4 1 3 /16 ---- ---- 5 3 /4 -- 12 1 3 /4 65 R7513 75 13 1 /6 208.0 4 1 /2 16 9,430 18 5 /8 31 7 /16 5 3 /4 3 3 /4 1 3 /16 ---- ---- 5 3 /4 -- 12 1 3 /4 130 R1006 100 6 5 /8 137.0 5 1 /8 20 5 /8 9,695 13 1 /4 20 11 /16 7 4 1 /8 5/8 ---- ---- 6 7 /8 -- 12 1 3 /4 90 R10010 100 10 1 /4 212.0 5 1 /8 20 5 /8 9,695 16 7 /8 27 15 /16 7 4 1 /8 5/8 ---- ---- 6 7 /8 -- 12 1 3 /4 110 Power pumps are suggested for these units. Collar Thru Lgth Wgt. Sugstd. Hand Pump 152

Hydraulic s 5 150 Ton Single-Acting, Spring Return, Low-Profile Flat Jacks Simplex RFS Series are designed specifically for near impossible lifting, clamping or positioning jobs where space is at a premium. Ideal for break loose or start up spreading jobs. These mini-monsters pack up to 150 tons of force into a convenient, portable package. Mounting Hole Dimensions H I Base Mounting Hole Dimensions 5 Ton 1 1 1 /8 7/32 through x 23/64 C Bore (1/4 Deep) 10 Ton 1 11 /32 1 13 /32 9/32 through x 27/64 C Bore (5/16 Deep) 20 Ton 1 9 /16 1 15 /16 25/64 through x 5/8 Bore (25/64) A Stroke B Min. Ht. C Ext Ht. Ram Bore Dia. Effect Area (sq. in.) Pres. @ cap. (psi) Oil Cap. Req d (cu.in.) D Body O.D. E Piston O.D. F Base To Port C/L G Piston O.D. Spring Ret. R50 5 5/8 1 5 /8 2 1 /4 1 1 /8.99 10,000.6 2 9 /16 1 5 /8 1 2.5 RFS10 10 1 11 /16 2 1 /8 1 11 /16 2.24 8,940 1.0 3 1 /4 2 3 /16 3/4 3.3 7/16 RFS20 20 2 1 /32 2 15 /32 2 3 /8 4.43 9,030 1.9 4 3 1 1 /8 6.0 RFS30 30 1/2 2 5 /16 2 13 /16 2 7 /8 6.49 9,250 3.2 4 1 /2 3 3 /4 3/4 1 3 /8 8.5 RFS50 50 2 5 /8 3 1 /4 3 1 /2 9.62 10,400 6.0 5 1 /2 4 1 /2 1 3 /4 14.3 RFS75 75 5/8 3 1 /8 3 3 /4 4 1 /2 15.90 9,440 10.0 6 1 /2 5 1 /2 2 1 /8 24.5 RFS100 100 3 3 /8 4 5 19.63 10,200 12.3 7 6 2 1 /2 31.0 RFS150 150 9/16 3 15 /16 4 1 /2 6 1 /4 30.66 9,785 17.2 8 1 /2 7 1 /2 15/16 3 50.5 Sugstd. Hand Pump P41/P71 P42/P72 www.rentlgh.com Jacking Equipment 153

Hydraulic s 10 100 Ton Single-Acting, Spring Return, Low-Profile Low Profile s Simplex RLS Series provides the ideal fit & force required for most bridge lifting and pier cap maintenance jobs. Compact, light weight & tough as nails, Simplex cylinders are at home on any construction site. Rentals@RentLGH.com Jacking Equipment A Stroke B Min. Ht. C Ext Ht. Ram Bore Dia. Effect Area (sq. in.) Pres. @ cap. (psi) Oil Cap. Req d (cu.in.) D Body O.D. E Piston O.D. F Base To Port C/L RLS101 10 1 1 /2 3 15 /32 4 31 /32 1 11 /16 2.23 8,940 3.4 2 3 /4 1 1 /2 9 11/16 RLS201 20 1 3 /4 3 7 /8 5 5 /8 2 3 /8 4.43 9,030 7.8 3 5 /8 2 11 RLS302 30 2 7 /16 4 5 /8 7 1 /16 2 7 /8 6.49 9,250 15.8 4 2 5 /8 3/4 15 RLS502 50 2 3 /8 4 13 /16 7 3 /16 3 1 /2 9.62 10,400 22.8 4 7 /8 2 3 /4 15/16 24 RLS1002 100 2 1 /4 5 9 /16 7 13 /16 5 19.63 10,200 44.2 6 1 /2 3 5 /8 1 1 /4 50 P140 Sugstd. Hand Pump P42/P72 154

Hydraulic s 10 1,000 Ton Double-Acting Double-Acting Push Cap. Pull Cap. Stroke A Min. Ht. B Ext. Ht. Pull Effect Area (sq. in.) Push Effect Area (sq. in.) Pres. @ Cap. (psi) Oil Cap. Req d (cu. in.) C Body O.D. Ram D Piston Bore O.D. Dia. RDA1010 10 4 10 16 1 /8 26 1 /8 0.80 2.23 8,960 22 2 7 /8 1 3 /8 1 11 /16 1 8 1 2 1 /4 14 1 1 /16 28 RDA308 8 1 /8 15 3 /4 23 3 /4 34 2 7 30 5 3.00 6.51 9,250 4 2 1 /8 40 /8 1 1 /2 16 1 3 5 /16 12 1 15 /16 RDA3014 14 1 /2 21 5 /8 36 1 /8 92.70 2 7 /8 64 RDA556 6 1 /8 13 1 /8 19 1 /4 46 3 3 /4 68 RDA5512 55 17 12 19 1 /8 31 1 /8 3.40 11.05 9,955 92 5 3 1 /8 3 3 /4 1 12 1 1 /2 5 12 1 3 /4 114 RDA5524 24 31 5 /8 55 5 /8 184 3 3 /4 201 RDA1006 6 1 /16 13 7 /8 19 15 /16 77 5 1 /4 140 100 45 9.08 21.65 9,239 7 4 3 1 /4 12 2 1 /2 7 12 2 1 /2 RDA10012 12 19 7 /8 31 7 /8 151 5 1 /4 187 RDA1506 150 67 6 1 /16 15 7 /16 21 1 /2 13.55 33.18 9,041 120 8 1 /2 5 6 1 /2 3 1 /2 12 2 3 /4 8 1 /2 12 2 3 /16 218 RDA15012 150 67 12 21 1 /2 33 1 /2 13.55 33.18 9,041 236 8 1 /2 5 6 1 /2 3 1 /2 12 2 3 /4 8 1 /2 12 2 3 /16 295 RDA2002 2 11 7 /16 13 7 /16 66 232 RDA2006 200 6 15 7 /16 21 7 /16 15.91 44.18 9,054 170 10 6 7 1 /2 9 3 /4 12 1 7 /8 315 RDA20013 13 22 7 /16 35 7 /16 368 440 RDA3002 2 13 1 /4 15 1 /4 101 277 RDA3006 335 6 17 1 /4 23 1 /4 20.62 70.9 10,000 302 12 8 9 1 /2 441 RDA30012 12 23 1 /4 35 1 /4 605 688 RDA4002 2 12 3 /8 14 3 /8 127 530 RDA4006 565 6 16 5 /8 22 5 /8 49.48 113 10,000 382 14 1 /2 9 12 670 RDA40012 12 22 7 /8 34 7 /8 762 880 RDA5002 2 16 1 /2 18 1 /2 156 722 RDA5006 500 6 20 1 /2 26 1 /2 54.19 132 10,000 471 16 10 13 953 RDA50012 12 26 1 /2 38 1 /2 942 1,300 RDA6002 2 15 17 158 917 RDA6006 664 6 19 25 44.17 122.71 10,000 472 17 10 12 1 /2 1,188 RDA60012 12 25 37 944 1,595 RDA8002 2 16 18 226 1,166 RDA8006 800 6 21 1 /2 27 1 /2 52.03 165.13 9,690 991 18 1 /2 10 14 1 /2 1,461 RDA80012 12 26 38 1,360 1,776 RDA10002 2 16 18 354 1,558 RDA10006 1000 6 20 26 50.27 227 8,810 1,071 21 15 17 2,058 RDA100012 12 27 39 2,142 2,808 Piston I.D. Thrds. F Piston Thrd. Depth Collar Thrds. G Collar Thrd. Lgth. www.rentlgh.com Jacking Equipment 155

Hydraulic s 30 1,000 Ton Single-Acting, Load Return, Lock Nut Lock Nut s 5% Note: 100 ton models have removable lifting eye bolts in lieu of carrying handles. Note: Eye bolts are removable. Rentals@RentLGH.com Jacking Equipment A Stroke B Min. Ht. C Ext. Ht. Ram Bore Dia. Effect Area (sq. in.) Pres. @ Cap. (psi) Oil Cap. Req d (cu. in.) D Body O.D. E Piston O.D. F Base To Port C/L RLN302 2 6 3 /8 8 3 /8 13.0 21.0 30 2 7 /8 6.49 9,240 4 2 7 /16 3/4 RLN306 6 10 3 /8 16 3 /8 38.9 35.0 RLN502 2 6 3 /4 8 3 /4 22.1 38.0 RLN506 50 6 10 3 /4 16 3 /4 3 3 /4 11.05 9,054 66.2 5 3 3 /16 25/32 63.0 RLN5010 10 14 3 /4 24 3 /4 133.0 100.0 RLN1002 2 8 10 40.0 87.0 RLN1006 100 6 12 18 5 19.63 10,200 118.0 6 3 /8 4 5 /16 1 1 /4 132.0 RLN10010 10 16 26 196.0 202.0 RLN1502 2 8 10 66.4 149.0 RLN1506 150 6 12 1 /4 18 6 1 /4 30.68 9,780 199.0 8 1 /2 5 9 /16 1 15 /16 221.0 RLN15012 12 18 30 398.0 311.0 RLN2002 2 9 1 /2 11 1 /2 88.4 233.0 RLN2006 200 6 13 1 /2 19 1 /2 7 1 /4 41.28 9,054 265.0 10 6 9 /16 2 1 /16 332.0 RLN20012 12 19 1 /2 31 1 /2 530.0 479.0 RLN3002 2 11 1 /2 13 1 /2 120.0 357.0 RLN3006 300 6 15 1 /2 21 1 /2 8 3 /4 60.13 9,978 361.0 12 7 13 /16 2 7 /16 485.0 RLN30012 12 21 1 /2 33 1 /2 722.0 677.0 RLN4002 2 13 13 /16 15 13 /16 174.00 520.0 RLN4006 400 6 17 13 /16 23 13 /16 10 1 /2 86.59 9,238 520.0 14 9 5 /16 3 675.0 RLN40012 12 23 13 /16 25 13 /16 1,040.0 905.0 RLN5002 2 14 3 /4 16 3 /4 208.0 927.0 RLN5006 500 6 18 3 /4 24 3 /4 11 1 /2 103.87 9,628 623.0 16 10 5 /16 3 3 /16 1,041.0 RLN50012 12 24 3 /4 36 3 /4 1,246.0 1,383.0 RLN6002 2 15 5 /8 17 5 /8 246.0 985.0 RLN6006 600 6 19 5 /8 25 5 /8 12 1 /2 122.79 9,778 738.0 17 1 /2 11 5 /16 3 1 /2 1,232.0 RLN60012 12 27 5 /8 39 5 /8 1,476.0 1,603.0 RLN8002 2 16 15 /16 18 15 /16 330.0 1,148.0 RLN8006 800 6 21 15 /16 27 15 /16 14 1 /2 165.13 9,690 991.0 18 13 5 /16 4 1 /8 1,407.0 RLN80012 12 27 15 /16 39 15 /16 1,982.0 1,795.0 RLN10002 2 19 5 /8 21 5 /8 402.0 1,818.0 RLN10006 1,000 6 23 5 /8 29 5 /8 16 201.06 9,950 1,206.0 21 14 13 /16 4 1 /4 2,178.0 RLN100012 12 29 5 /8 41 5 /8 2,412.0 2,178.0 156

Hydraulic s 12 100 Ton Single-Acting, Spring Return, Center Hole Single Acting Base Mounting Holes Size Thread Depth Bolt Circle Dia. 12 Ton 5/16 18 5/16 2 20 Ton 3/8 16 7/16 3 1 /4 30 Ton 3/8 16 3/8 3 5 /8 60 Ton 1/2 13 7/16 5 1 /8 100 Ton 5/8 11 3/4 7 Cap. Stroke A Min. Ht. B Ext. Ht. Effect Area (sq. in.) Pres.@ Cap. (psi) Oil Cap. Req d (cu. in.) C Body O.D. D Piston O.D. E Base To Port C/L F Center Hole Dia. H Collar Collar Thrd. Thrds. Lgth. Piston Thrds. RC120 3/4 16 5/16 2 3 /16 2 1 /2.90 7/16 RCQ120 3/4 10 G Piston Thrd. Lgth. RC121 12 2.36 10,185 2 3 /4 1 3 /8 49/64 2 3 /4 16 1 13 /16 1 5 /8 4 3 /4 6 3 /8 4.5 RC1211 25/32 3/4 16 5/8 5/8 3.5 RC123 3 7 1 /4 10 1 /4 8.3 10 RC202 2 6 3 /16 8 3 /16 11 17 20 5.30 7,545 4 2 1 /8 51/64 1 1 /16 3 7 /8 12 1 1 /2 1 9 /16 16 3/4 RC206 6 11 3 /16 17 3 /16 32 31 RC302 2 1 /2 7 9 1 /2 22 26 30 8.64 6,950 5 2 1 /2 1 5 /16 4 1 /2 12 1 3 /4 1 13 /16 16 7/8 RC306 6 1 /8 12 1 /4 18 3 /8 64 52 13/16 RC603 3 8 21 /32 11 21 /32 44 68 60 14.58 8,230 6 3 /4 4 2 1 /8 6 1 /4 12 2 2 3 /4 16 3/4 RC606 6 12 21 /32 18 21 /32 88 80 RC1003 100 3 9 12 20.60 9,700 62 8 1 /4 5 1 3 1 /8 4 16 1 99 6.5 www.rentlgh.com Jacking Equipment 157

Hydraulic s 30 1,000 Ton Single-Acting, Load Return 5% Load Return Note: 100 ton models have removable lifting eye bolts in lieu of carrying handles. Note: Eye bolts are removable. Rentals@RentLGH.com Jacking Equipment A Stroke B Min. Ht. C Ext. Ht. Ram Bore Dia. Effect Area (sq. in.) Pres. @ Cap. (psi) Oil Cap. Req d (cu. in.) D Body O.D. E Piston O.D. F Base To Port C/L RLR306 30 6 9 3 /8 15 3 /8 2 7 /8 6.49 9,240 38.9 4 2 3/4 32.0 RLR502 2 5 7 /16 7 7 /16 22.1 30.0 RLR506 50 6 9 7 /16 15 7 /16 3 3 /4 11.05 9,054 66.3 5 3 25/32 55.0 RLR5010 10 13 7 /16 23 7 /16 133.0 92.0 RLR1006 100 6 10 9 /16 16 9 /16 118.0 90.0 5 19.63 10,200 6 3 /8 3 3 /8 1 1 /4 RLR10010 10 14 9 /16 24 9 /16 196.0 126.0 RLR1502 2 7 9 66.4 117.0 RLR1506 150 6 11 17 6 1 /4 30.68 9,778 199.0 9 5 9 /16 1 15 /16 189.0 RLR15012 12 17 29 398.0 297.0 RLR2002 2 8 10 88.4 184.0 RLR2006 200 6 12 18 7 1 /4 41.28 9,054 265.0 10 6 9 /16 2 1 /16 282.0 RLR20012 12 18 30 530.0 429.0 RLR3002 2 11 1 /2 13 1 /2 120.0 277.0 RLR3006 300 6 13 3 /4 19 3 /4 8 3 /4 60.13 9,978 361.0 12 7 13 /16 2 7 /16 405.0 RLR30012 12 19 3 /4 31 3 /4 722.0 597.0 RLR4002 2 11 1 /2 13 1 /2 174.0 455.0 RLR4006 400 6 15 1 /2 21 1 /2 10 1 /2 86.59 9,238 520.0 14 6 9 /16 3 612.0 RLR40012 12 21 1 /2 33 1 /2 1,040.0 842.0 RLR5002 2 12 5 /8 14 5 /8 208.0 627.0 RLR5006 500 6 16 5 /8 22 5 /8 11 1 /2 103.87 9,628 623.0 16 10 5 /16 3 3 /16 855.0 RLR50012 12 22 5 /8 34 5 /8 1,246.0 1,197.0 RLR6002 2 13 1 /2 15 1 /2 246.0 655.0 RLR6006 600 6 17 1 /2 23 1 /2 12 1 /2 122.71 9,778 738.0 17 1 /2 11 5 /16 3 1 /2 902.0 RLR60012 12 23 1 /2 35 1 /2 1,476.0 1,273.0 RLR8002 2 14 7 /16 16 7 /16 330.0 997.0 RLR8006 800 6 18 7 /16 24 7 /16 14 1 /2 165.13 9,690 991.0 18 13 5 /16 4 1 /8 1,256.0 RLR80012 12 24 7 /16 36 7 /16 1,982.0 1,644.0 RLR10002 2 16 1 /8 18 1 /8 402.0 1,523.0 RLR10006 1,000 6 20 1 /8 26 1 /8 16 201.96 9,950 1,206.0 21 14 15 /16 4 1 /4 1,883.0 RLR100012 12 26 1 /8 38 1 /8 2,412.0 2,423.0 158

Hydraulic Hand Pumps Light and Heavy Hand Pump P300 P140 P42 P20 P22 Speed 2 Pressure Rating (PSI) 1 Stage 200 2 Stage 2,850 1 Stage 200 2 Stage 10,000 Light Hand Pumps For Single-Acting s Oil Volume Per Stroke (cu. in.).82.16.23.06 Usable Oil (cu. in.) 20 A B C D E Slot Size F G 13 11 1 /2 2 5 /8 1 1 /2 19/32 5 3 /4 4 3 /4 13 1 /2 11 1 /2 2 5 /8 1 1 /2 19/32 5 3 /4 5 3 /4 P41 1 10,000.16 45 23 21 3 /4 5 5 3 /4 5 3 /4 18 1 Stage 200 P42 2 Stage 10,000 2 1 Stage 200 P82A 2 Stage 10,000.82.16.82.16 45 23 21 3 /4 5 5 3 /4 5 3 /4 19 145 23 17 1 /2 5 1 /2 5 1/2 6 5 /8 5 3 /4 24 Two Speed Hand Pumps For Single & Double Acting s Speed Pressure Rating (PSI) Oil Volume Per Stroke (cu. in.) Usable Oil (cu. in.) A B C 10 P140 2.8 175 24 13 /16 27 1 /4 23 5 /16 26 P300 Single 1 Stage 400.24 300 28 1 /2 31 26 1 /2 37 P230 Acting 2 Stage 10,000 7.7 230 9 49 25.3 /8 22 3 /4 P461 460 12 61 P140D 2.8 175 29 1 /2 31 1 /2 23 5 /16 30 P300D Double 1 Stage 400.24 300 32 11 /16 34 11 /16 26 1 /2 41 P230D Acting 2 Stage 10,000 7.7 230 9 49 25.3 /8 22 3 /4 P461D 460 12 61 www.rentlgh.com Jacking Equipment 159

Gasoline Hydraulic Pumps Gas Powered PG40/50 and G4 Series PGM4042 Reservoir Size (Gal.) Valve Style Function Motor Type Flow Rate PGTM8035 5 VP3 Standard 3 Position; 3 Way Manual Lever Advance/Hold/Retract Tecumsa; 8 HP PGTM8036 10 VP3 Standard 3 Position; 3 Way Manual Lever Advance/Hold/Retract Tecumsa; 8 HP PGTM8045 5 VP4 Standard 3 Position; 4 Way Manual Lever Advance/Hold/Retract Tecumsa; 8 HP PGTM8046 10 VP4 Standard 3 Position; 4 Way Manual Lever Advance/Hold/Retract Tecumsa; 8 HP 680 cu. in. @ 1,500 psi 140 cu. in. @10,000 psi 680 cu. in. @ 1,500 psi 140 cu. in. @10,000 psi 680 cu. in. @ 1,500 psi 140 cu. in. @10,000 psi 680 cu. in. @ 1,500 psi 140 cu. in. @10,000 psi 130 185 130 185 G4833 Rentals@RentLGH.com Jacking Equipment Pressure Rating (psi) 1st Stage 2nd Stage 1st Stage 2nd Stage C Output Flow (cu. in./min.) Motor Value Type Reservoir G4833 1,100 10,000 700 50 4 HP 3W, 3P 2.5 53 G4835 1,100 10,000 700 50 4 HP 3W, 3P 5 108 G4843 1,100 10,000 700 50 4 HP 4W, 3P 2.5 53 G4845 1,100 10,000 700 50 4 HP 4W, 3P 5 108 B A Usable Resevoir ; Gallons Dimensions A B C 1.5 15.13 8.75 22.34 2.5 17 9.75 22.34 5 25.10 11.75 19.54 10 25.10 11.75 23.97 20 28 19.60 22.84 160

Electric Hydraulic Pumps 50 and G6 Series Electric Pump PEM 5006 Pressure Rating (psi) Output Flow (cu. in. / min) Motor Spec. 1st Stage 2nd Stage 1st Stage 2nd Stage (vac) (amps) Valve Type Pendant Control Reservoir PEM5066 1,500 10,000 650 110 230 10 4w, 3P (L) - 40 221 B C D A E Usable Reservoir (gal.) G6335 C Usable Oil (cu. in.) A Dimensions B C D 40 9,200-12 5/16 - - - B D E A E Pressure Rating (psi) 1st Stage 2nd Stage Output Flow (cu.in./min.) 1st Stage 2nd Stage (vac) Motor (amps) Value Type Pendant Reservoir G6335 1,500 10,000 750 100 230 9.5 3W, 3P ---- 5 162 G6336 1,500 10,000 750 100 230 9.5 3W, 3P ---- 10 217 G6336L 1,500 10,000 750 100 230 9.5 3W, 3P (L) ---- 10 218 G6365 1,500 10,000 750 100 230 9.5 3W, 3P Solenoid 5 165 G6366 1,500 10,000 750 100 230 9.5 3W, 3P Solenoid 10 220 G6366L 1,500 10,000 750 100 230 9.5 3W, 3P (L) Solenoid 10 221 G6346 1,500 10,000 750 100 230 9.5 4W, 3P ---- 10 210 G6347 1,500 10,000 750 100 230 9.5 4W, 3P ---- 20 311 G6347L 1,500 10,000 750 100 230 9.5 4W, 3P (L) ---- 20 312 G6375 1,500 10,000 750 100 230 9.5 4W, 3P Solenoid 5 165 G6376 1,500 10,000 750 100 230 9.5 4W, 3P Solenoid 10 220 G6376L 1,500 10,000 750 100 230 9.5 4W, 3P (L) Solenoid 10 221 Dimensions Usable Reservoir ; Gallons Usable Oil (cu. in) A B C D E 5 1,150 19.62 11.75 20.52 8.46 25.10 10 2,300 19.62 11.75 24.76 12.71 25.10 25 4,600 23.50 19.60 24.51 12.46 28 www.rentlgh.com Jacking Equipment 161

Electric Hydraulic Pumps ZU Pump 2 Gallon 5 Gallon Rentals@RentLGH.com Jacking Equipment Usable Reservoir (gal) A B Dimensions C D E F 1.0 17.0 5.6 11.0 6.0 2.0 19.5 8.0 11.3 6.6 2.5 17.6 6.1 16.5 12.0 15.1 11.0 5.0 18.6 7.1 16.3 16.6 19.7 15.6 10.0 22.0 10.6 15.7 19.9 22.7 18.9 Motor Size (hp) 100 psi Output Flow Rate (in. 3 /min) 700 psi ZU4 Performance 5000 psi 10,000 psi 1.7 700 535 76 60 Motor Electrical Specification 115 1-50 /60 230 1-50 /60 Sound Level (dba) Relief Valve Adjustment Range (psi) 85-90 2,000-10,000 162

Hydraulic Accessories High Pressure Hoses & Accessories High Flow HD & HDC Series 3/8 I.D. hose is recommended to achieve higher retraction speeds and minimal flow restrictions. These heavy duty hoses are rated at 10,000 psi with a minimum burst pressure of 30,000 psi. Hydraulic Hoses Length (ft.) Hose End Hose End I.D. HD3 HD6 HD10 HD20 HD50 HDC3 HDC6 HDC10 HDC20 10 20 30 50 75 100 150 175 200 3/8 NPTF Male 3/8 NPTF Male 3/8 NPTF Male C213 Coupler* 3/8 HDC50 *All hoses with couplers includes CR215 Dust Cap. Note: Recommended for use with Suc-O-Matic Pumps. C213 Coupler* C213 Coupler* In this fixed outdoor application Simplex hand pumps and hoses are permanently attached to this mineral processing machine. The desert environment is tough on hydraulic equipment. Simplex provides us the reliability we need. www.rentlgh.com Jacking Equipment 163

Hydraulic Accessories Manifolds / Fittings & Oil High Pressure Manifolds Pump Mounted 4 Control Manifold Kit: The M1 control manifold incorporates (4) station shut-off/flow control valves, 18 hose, gauge port, (4) high flow couplers and pump mounting hardware. Two or more manifolds can be coupled together for larger systems. For replacement hose order #89521 Pump Mounted 4 Manifold Kit: The M2 manifold includes 18 hose and pump mounting hardware. Two or more manifolds can be coupled together for larger systems. For replacement hose order #89521 Pump Mounted 2 Control Manifold Kit: The M2A control manifold incorporates (2) station shut-off/flow control valves. Two or more manifolds can be coupled together for larger systems. 6 Port Inline Hex Manifold: The M3 inline hex manifold features (6) 3 /8 NPTF threaded ports & mounting holes. Pump Mounted 4 Control Manifold Kit: The M4 control manifold incorporates (4) station shut-off/flow control valves. Two or more manifolds can be coupled together for larger systems. Rentals@RentLGH.com Jacking Equipment Simplex Hydraulic Oil Number A01 A05 A055 Hydraulic Oil Qty. 1 Gallon 5 Gallon 55 Gallons 3/8 NPTF High-Pressure 10,000 PSI Fittings Hex Nipple 3 Nipple 6 Nipple 90 Elbow 90 St. Elbow 3/8 M to 1/4 F Special, high pressure formulated, premium grade oil for all Simplex hydraulic products. High viscosity index insures maximum lubricity over a wide range of operating temperatures. Tee Coupling Cross 1/4 M to 3/8 F F1 F3 F6 F7 F9 F10 F11 F13 F15 F17 Simplex Hydraulic Oil Viscosity Index 100 min. VIS, SSU @ 100 F 150-155 VIS, SSU @ 210 F 45 50 VIS, SSU @ 0 F < 15,000 Pour Point -50 F Flash Point 400 F Analine Point 204.8 F Includes: Anti-Foam, Anti-Rust and Low Temperature Additives 164

Hydraulic Accessories Couplers 3/8 NPTF C213-Hose Half Coupler 3/8 & 1/4 NPTF High-Flow Couplers These premium grade couplers provide maximum fluid flow and are plated to resist corrosion. Half Couplers have male 3/8 NPTF threads C211-Ram Half Coupler & high strength rubber dust caps; Hose Half Couplers have female 3/8 NPTF threads. CR215 Dust Cap C209 Coupler Complete with 2 Dust Caps 1/4 NPTF CT201-Ram Half Coupler CT202 Hose Half Coupler CT200 Coupler Complete with 2 DUst Caps For use on smaller tools, pumps and any tool with 1/4 threads. These couplers are plated to resist corrosion. Half Couplers have male 1/4 NPTF threads; Hose Half Couplers have female 1/4 NPTF threads. 3/8 & 1/4 NPTF Flush Face/No Spill Couplers 3/8 NPTF C513-Hose Half Coupler C515-Dust Cap Ram Half C516-Dust Cap Hose half Unique flush face design features push to connect operation with a sleeve lock, and non-spill dry disconnect operation. Easy cleaning minimizes system contamination. This coupler should be used where ever oil spillage constitutes a safety or environmental hazard. Couplers have 3/8 NPTF threads. C511-Ram Half Coupler 1/4 NPTF CT211 Ram Half Coupler with Dust Cap C509 Coupler Complete with 2 Dust Caps CT210 Hose Half Coupler with Dust Cap CT212 Coupler Complete with 2 Dust Caps Unique flush face design features push to connect operation with an auto lock sleeve on the CT211, and non-spill dry disconnect operation. Easy cleaning minimizes system contamination. This coupler should be used wherever oil spillage constitutes a safety or environmental hazard. Couplers have 1/4 NPTF threads. www.rentlgh.com Jacking Equipment 165

Hydraulic Accessories Analog & Digital Gauges Analog & Digital Gauges Gauge Description Dimensions G5 2.1/2 Gauge 500 PSI Increment 3/8 M 1/4 F GA1 Gauge Adapter 3/8 F The G5 is a high quality compact liquid filled gauge that reads in both PSI and Bar. Liquid filled to dampen needle vibration, the G5 is perfect for applications up to 10,000 psi. Liquid filled dampens needle vibration. +/-1% full scale accuracy. 500 psi increment. Stainless steel casing. G6 4 Gauge 500 PSI Increment GA1 Gauge Adapter The G6 is a larger, easy to read liquid filled gauge that s in both PSI and Bar with increments of 500 psi. The calibrated scale reads from 0-10,000 psi with 10,000 psi to 15,000 psi as a warning zone. Liquid filled dampens needle vibration. +/- 1% full scale accuracy. Large easy to read 4 face. Rubber blowout plugs for safety. Stainless steel casing. G7 4 Gauge 100 PSI Increment GA1 Gauge Adapter The G7 is a larger, easy to read liquid filled gauge that s in both PSI and Bar with increments of 100 PSI/10Bar. The calibrated scale reads from 0-10,000 psi. Liquid filled dampens needle vibration. +/- 1% full scale accuracy. Large easy to read 4 face. Rubber blowout plugs for safety. Stainless steel casing. Standard on all Simplex Torque Wrench Pumps. Rentals@RentLGH.com Jacking Equipment GD1 2 1/2 Digital Gauge GD2 4 Digital Gauge Tonnage Gauge GA1 Gauge Adapter GA1 Gauge Adapter GA1 Gauge Adapter The GD1 is designed for the high cycle pressure application where mechanical gauges don t hold up. The GD1 is a direct mount, compact gauge with an all stainless steel sensor that is vibration & shock resistant. Self powered Lithium batteries. Full 4 digit display. +/-.25% full scale accuracy. 10 million cycle life minimum. The GD2 digital gauge combines the best features of analog and digital instruments. The 0.75 high full 4 digit display is easily read at a distance and the analog bar graph allows instant estimation of changing pressures. The all stainless steel sensor is vibration and shock resistant. 0.75 characters and 270 bar graph analog readout. Splash proof phenolic housing. +/-.25% full scale accuracy. Keypad enable/disable of peak high or peak low hold. Calibrated Range Face (0-10,000 psi) Diameter s Used With and Tons GT5 0 5, 10, 15 All 5, 10 & 15 Ton s GT20 0 20, 50 All 20 RFS & RLS 50 Ton s GT25 0 25, 55, 100 All 25, 55 & RFS & RLS 100 Ton s GT30 0-30, 50, 100 4 30 Ton s, 50 & 100 RLR & RLN GT100 0-100, 150, 200 RDA100 & 200 Series, RLR & RLN 150 & 200 GTH12 0-12, 20, 30 12, 20 & 30 Ton RC & RCD Series GTH60 0-60, 100, 150 60, 100, & 150 Ton RC & RCD Series 166

Hydraulic Jacks.75 10 Ton Spreader Jack S3000A S2000A S2000A 5 Ton Hydraulic Spreader Gat R Jaw Spreaders Pressure @ (PSI) Oil Required (cu. in.) Width S2000A 1.61 2.01 5 10,000 S3000A.75 3.91 2.01 25 Suggested Hand Pump P42 S3000A Pres. @ Cap. Cap. (PSI) 5 Ton Hydraulic Spreader Oil Cap. Req. (cu. in.) Min. Spread Max. Suggested Hand Pump SF5 5 10,000 5 17.09 3 P22 610 10 Ton Push/Pull Jack 10 Ton Push/Pull & Ratchet Screw Assembly Cap. Offset Cap. Travel Screw Dia. Length 610-15 10 Ton Ratchet Screw Assembly Wgt. Order Number Steel Lever Bars Length Dia 610 10 2 4 1 /2 1 1 /4 10 13 5LB24 24 3/4 4 610-15 10 2 ---- 1 1 /4 ---- 5 5LB24 24 3/4 4 Wgt. www.rentlgh.com Jacking Equipment 167

Hydraulic Jacks 2 10 Ton Toe Jack TJH5 Heavy equipment movers have long realized the benefits of Simplex toe jacks. Truly a universal tool, hydraulic toe jacks can do a wide variety of jobs faster & safer than standard jacks. With toes heights starting at 1 and capacities up to 10 tons, Simplex hydraulic toe jacks are the first choice for transformer maintenance, heavy hauling, structural moving, and rigging. Rentals@RentLGH.com Jacking Equipment Cap. Stroke Minimum Toe Cap Base Area Max. Handle Effort Method of Return TJH2 2 4 7 /16 5/8 9 1 /4 4 59 /64 x 7 51 Load 18 TJH5 5 4 5 /8 1 11 3 /4 7 1 /4 x 10 5 /8 33 Spring 53 TJH10 10 5 7 /8 1 1 /4 13 1 /8 9 1 /2 x 11 1 /4 38 Spring 85 TJH109 10 9 2 1 /4 22 6 1 /2 x 10 80 Spring 56 TJH109LS 10 9 2 11 /16 16 1 /8 6 x 9 73 Spring 41 Note: Handles are included with all self-contained models. 168

Hydraulic Jacks 5 60 Ton Toe Jack PS1230C PS630C Claw Stroke (in) Lift Per Stroke (in) of Jack (lbs) of Claw (lbs) Working Pressure (PSI) Effort on Lever (max) (lbs) Oil (pints) Service Kit Number 9501W 5 5 7.21 40 8 99 995125 PS630C 30 12 6.026 34 11 9,350 115 1.5 133511 PS1230C 30 12 12.026 52 17 9,350 115 3 133511 PS660C 60 24 6.013 61 34.5 9,350 115 3 133518 PS1260C 60 24 12.013 97 47 9,350 115 5 133518 A Width B Center Ram to Claw C Base Length Dimensions D Overall Depth F Ram Diameter H Closed J Base to Claw K Claw Depth 9501W 4.5 3.17 8.66 10.35 2.24 12.8 1.61 2.05 PS630C 5.5 5.265 10.75 9.25 3 11.062 2.875 1.77 PS1230C 5.5 5.625 10.75 12.25 3 18.5 2.875 1.77 PS660C 7.5 7.125 13.375 11.25 4.25 12.875 2.875 1.89 PS1260C 7.5 7.125 13.375 15.125 4.25 21 2.875 1.89 www.rentlgh.com Jacking Equipment 169

Synchronus Hydraulic Pump Hydra-Pac 20-2-4D Sync System Rentals@RentLGH.com Jacking Equipment Engine Type HP Hydra-Pac Synchronous Power System Features Synchronized control of 4 lifting points. Ability to safely raise/lower multiple cylinders. Safe and efficient control. Accuracy of +/ 5% regardless of pressure. Easy to operate simple and user friendly. Mechanical operation - no wires or electronics. Standardized components. Ergonomic design. Removable wheels. **Always follow operating manual instructions and safe jacking practices.** No. of Ports Flow Rate per Active Port (GPM) All Ports 2 Ports Paired Maximum Pressure (PSI) Oil Reservior (GAL) (lb) Dimensions (LxWXH) 20-2-4D Diesel 20 4.5 1.0 10,000 30 1450 84 x 42 x 56 For use with standard 10,000 psi single or double acting cylinders. Ports can be paired to double flow rate at full pressure. 170

Heavy Track Skidding System HT500 Hydraulic Skidding System HT System Features A safer alternative to overhead lifting or rollers. No come-a-longs, winch lines, or hold backs required. Fully bi-directional track. Simple lug and pin connections. s automatically reset into ratchet tracks. Low profile perfect for areas with limited space/access. Leap frog tracks to move longer distances. Track will carry loads over unsupported spans. Durable low-maintenance graphite slide surface. Safety stop blocks. Can be operated with most 10,000 psi doubleacting pumps, but synchronous pumps are recommended. System (Tons) Hydra-Slide Skid System Width Track Section Length Track Section (lbs/ft) Load Bearing Track Skid Shoe Size Maximum Pressure (PSI) Skidding Speed (ft/hr) HT500 500 8 21 10 & 15 190 Yes 24 x 18 10,000 55* *Skidding speed determined using 20-2-4D HPU Note: There is a total of 50 of double track available for rent. www.rentlgh.com Jacking Equipment 171

Heavy Track Skidding System HT500 Hydraulic Skidding System Rentals@RentLGH.com Jacking Equipment 172

Synchronous Lifting 8 24 Point Lift System The solution for up to 8 24 lifting points with load control Features Control up to 24 lifting points Stroke and load controlled movement for positioning and weighing Accuracy of 0.040 between leading and lagging cylinders Data storage and recording capabilities Load and stroke alarms for optimal safety For use with standard single or double-acting cylinders Integrated 10,000 psi hydraulic pump and controls 3 Phase Ports 220V 440V 8-Port x x 12-Port x x 24-Port x Typical Synchronous Lifting Applications Bridge lifting and repositioning Bridge launching Lifting and lowering of heavy equipment Leveling of existing structures and buildings Structural Testing Lifting and weighing of oil platforms Tunnel Jacking and pushing www.rentlgh.com Jacking Equipment 173

Synchronous Lifting 8 24 Point Lift System The solution for up to 8 24 lifting points with load control Touch screen display for ESS Synchronous Lift Controller 1) Load Readings 2) On/Off 3) Absolute Sensor Position 4) Relative Sensor Position 5) Individual Load Readings 6) Manual Controls 7) Stroke Controls 8) Load Controls 9) Relative Position Reset Rentals@RentLGH.com Jacking Equipment Typical layout for a 4-point synchronous lifting system 1) Hydraulic Pump 2) PLC Control with Touch Screen 3) Hydraulic s 4) Stroke Sensors 5) Hydraulic Hoses 6) Sensor Cables 7) Solenoid Control Valves 8) Pressure Transducer 174

Need Additional Jacking Equipment? Please contact LGH today! 800-878-7305 or rentals@rentlgh.com Hand Pump Mechanical Jacks Hydraulic s High Tonnage s Toe Jacks Gas or Electric Pumps Sync Lift Flat Jack s Air Bags www.rentlgh.com Jacking Equipment 175