Mitsubishi ETACS - Smart Wiring System (SWS) Webpage Contents, click to jump to the location... Adjustment function - User Mode - These settings can be changed by the user, without a dealer. Adjustment function - Dealer Mode - These settings can only be modified by a dealer with a MUTII/III unit. Registering Transmitter Keys with ETACs These settings can be done by the user, without a dealer. Enabling/Disabling the hazard light answerback function can be changed by the user. Enabling/disabling the horn answerback function can be changed by the user. Adjustment function (User Mode) By setting the various switches to match the conditions for entering adjustment mode, you can switch the security alarm function on and off, or adjust the warning output. Any adjustments made are saved, even when the battery is disconnected. 1. Entering adjustment mode (1) Set the following switches as indicated. Driver s door switch: ON (driver s door open) Key reminder switch: ON (ignition key removed) Lighting switch: OFF (2) If the windscreen washer switch is switched on continuously for 10 seconds or more (by pulling the wiper lever towards you), then the ETACS ECU buzzer will sound once, and the system will enter adjustment mode. In this state (and keeping the wiper lever pulled towards you) the setting can be changed each time you press the unlock switch on the transmitter. 2. Adjusting the security alarm functions You can switch the security alarm function on and off, and change the alarm time, in the following sequence. (After option c, the sequence starts again from a.) a. Security alarm function OFF. (Initial state): Buzzer sounds once. b. Security alarm function ON. (Hazard and horn used for alarm): Buzzer sounds 3 times. c. Security alarm function ON. (Horn only used for alarm): Buzzer sounds 5 times. 3. Cancelling adjustment mode The adjustment mode is cancelled when any one of the following conditions is met. Driver s door switch: OFF (Driver s door closed) Key reminder switch: OFF (ignition key inserted) Lighting switch: ON Windscreen washer switch: OFF If 30 seconds have elapsed without the unlock switch being pressed. Note 1 / 31
1. Although the wiper washer switch and transmitter are operated during adjustment mode, the wiper/washer and keyless entry system are not activated by these operations. 2. This adjustment function is also described in the Owner s Manual, so that users are able to perform the adjustment procedure themselves. 3. The user s wishes should be confirmed fully before setting up this function. Adjustment function (Dealer mode) The following functions can be adjusted from the MUT-II/III. Any adjustments made will be saved, even if the battery is disconnected. Door ajar warning. If any one of the doors, including the boot, is open whilst the vehicle is travelling, then this function warns the driver that a door is open by sounding a buzzer and causing a door ajar indicator light to flash on the combination meter.. Turn indicator buzzer This function causes a buzzer to sound in synchronization with the hazard lights and turn indicator lights. Keyless entry system hazard light answer back function This function allows the driver to confirm a lock/unlock operation, even when he or she is away from the car. The hazard lights flash when a lock or unlock operation is performed by the keyless entry transmitter. Operation of electric window and sunroof by multi-mode keyless entry system This function causes the electric window and sunroof to close when the keyless entry transmitter is operated, even when the driver is away from the car. Timer lock delay after keyless entry unlock If any door, including the boot, is not opened after the doors have been unlocked by operation of the keyless entry transmitter, then after a prescribed time delay, the doors are automatically locked again. Electric window and sunroof timer function. This function allows the electric window and sunroof to be operated for a prescribed time, even after the ignition switch has been set to the LOCK (OFF) position. Electric window lock driver operation This function allows electric windows other than the driver s window to be operated by the electric window main switch, when the electric window lock switch built into the electric window main switch has been pressed. Vehicle speed sensitive wiper function This function changes the intermittent wiper period in accordance with the intermittent wiper adjustment knob and the vehicle speed, when the windscreen wiper switch is set to the intermittent position. Rear wiper intermittent period When the rear wiper switch is on, the rear wipers work intermittently. This function sets the rear wiper to continuous operation, when the rear wiper 2 / 31
switch is operated continuously. Automatic return function for motorised retractable door mirror This function opens the door mirrors automatically if the vehicle is travelling with the door mirrors retracted. Other methods can also be used to perform the retract / return operation of the door mirrors. Head light automatic cut-off function This function automatically turns off the head lights if the driver s door is opened when the lighting switch is set to the TAIL, AUTO, or HEAD position, and the ignition switch is set to LOCK (OFF). Interior light delayed switch off period This function causes the interior lights to switch off automatically after a prescribed delay, when the door has been closed with the ignition switch in the LOCK (OFF) position. Interior light automatic cut-off function This function automatically switches off the interior lights after a specified time delay if they have been left on with the ignition switch in the LOCK (OFF) position. Security alarm Switches the security alarm function on and off. Adjustment during electric window key off timer This function allows electric windows other than the driver s window to be operated during operation of the electric window timer. Initialise all functions (return to initial settings) This function returns all the adjusted functions to their original factory settings. Item No. MUT item displayitem MUT adjustment displaydetails of adjustm 2 HD auto cut-off Head light 3 / 31
automatic cut-off function Function ON (A) Function ON: The tail lights are automatically switched off, 4 / 31
if turned on when the ignition switch is at the LOCK (OFF) position. 5 / 31
Function ON (D) Function ON: The tail lights are not automatically switched off, if turned on 4 Speed sensitive wiper function Vehicle speed sensitive wiper function Function ON Function ON (initial setting) Function OFF Function OFF 5 Door mirror Motorised 6 / 31
retractable door mirror: automatic return function Speed sensitive 7 / 31
function ON Vehicle speed sensitive deployment (initial setting) IG operated function ON Linked to ignition Keyless operated function ON Linked to keyless entry Function OFF No function 6 (*1) Keyless (horn) Keyless entry 8 / 31
horn answer back Lock operated Sounds at each lock operation Lock operated twice Sounds when lock is operated twice consecutively (within 1 second) Function OFF Function OFF 8 (*1) Keyless (horn) 9 / 31
night time Keyless entry horn answerback: 10 / 31
night time disabling Normal Operates according to keyless entry horn answerback 11 / 31
adjustment function setting Night time operation disabled Operates according to keyless entry horn answerback adjustment function setting, 12 / 31
but horn sound disabled during night time 9 Keyless (hazard) Keyless entry system: hazard 13 / 31
answer back function Light up on lock, unlock Function ON for both lock and unlock (initial setting) Light up on lock only Function ON for lock only Light up on unlock only Function ON for unlock only Function OFF Function OFF 10 Keyless (P/W) Multi-mode 14 / 31
keyless entry system: Electric window and sunroof operation Open and close Both close and open 15 / 31
operations (open operation for windows only) Close only Close operation only (initial setting) Function OFF Function OFF 11 Security alarm Security alarm Horn and hazard Hazard only Function ON: Hazard only Function OFF Function OFF (initial setting) 16 / 31
15 Turn indicator buzzer Turn indicator light operating sound function Function ON Function ON Function OFF Function OFF (initial setting) 16 Interior light response time Interior light delayed switch 17 / 31
off time 60 s 60 s 30 s 30 s 15 s 15 s 7.5 s 7.5 s NO delayed switch off 0 s (no delay operation) 18 Key off timer period Electric window & sunroof timer 18 / 31
function period Timer function OFF Timer function OFF 30 s 30 s (initial setting) 3 min. 3 min. 10 min. 10 min. 19 P/W key off timer Operational adjustment 19 / 31
during electric window key off timer (*2) Normal operation Accepts normal operation 20 / 31
during timer period (initial setting) Main S/W operation prohibited Prohibits operation of electric windows (except driver s) from electric window main switch, during timer period 21 / 31
24 Keyless timer lock T Timer lock time after keyless entry unlock 30 s 30 s (initial setting) 60 s 1 min. 120 s 2 min. 180 s 3 min. 26 Door ajar Function buzzerdoor ajar warning function Function ON Function ON (initial setting) 22 / 31
Function OFF Function OFF 28 Rear wiper INT period Rear wiper intermittent period 8 s 8 s: No continuous operation 23 / 31
(initial setting) 4 s (continuous ON) 4 s (continuous ON) 8 s (continuous ON) 8 s (continuous ON) 16 s (continuous ON) 16 s (continuous ON) Continuous operation Continuous operation (no intermittent operation) Note 1. *1 optional: Can only be adjusted when the smart entry system is fitted. After fitting the smart entry system, a list of adjustable functions will be displayed when the entry system is operated for the first time. If all the functions are initialised, then the adjusted items will be deleted, but by activating the smart entry system, the list of adjusted functions will be displayed again. 2. *2 This adjustment item restricts the operation of the electric window timer 24 / 31
function, and is used when performing Inspection procedure D-8 Electric window comes down automatically. Registering Transmitter Keys with ETACs Each individual secret code is registered inside the transmitter, and so it is necessary to register these codes with the EEPROM inside the receiver in the following cases. When the transmitter or ETACS-ECU is replaced If more transmitters are to be used If it appears that a problem is occurring because of faulty registration of a code. A maximum of four different codes can be stored in the EEPROM memory (four different transmitters can be used). When the code for the first transmitter is registered, the previously registered codes for all transmitters are cleared. Therefore, if you are using four transmitters or are adding more transmitters, the codes for all transmitters must be registered at the same time. 25 / 31
HOW TO REGISTER SECRET CODE 1.Insert the ignition key into the key cylinder and check that the doors have been locked normally when the ignition key is turned. 2.Insert the ignition key into the key cylinder. 3a.Turn the ignition switch to the "LOCK" (OFF) position and then connect data link connector terminal 1 to ground. 3b.Connect the OBDII vehicle data link connector terminal 1 to ground (pin4 or pin5). NOTE: Connecting terminal 1 of the data link connector to ground will put the system in secret code registration standby mode. 4.Push the hazard warning light switch six times within 10 seconds. NOTE: At this time the code registration monitor request is output and becomes registration mode (all doors locked and then all doors unlocked). NOTE: The hazard warning light switch is turned on and off alternately whenever it is pushed. 5.Press the transmitter button, and then press it two times within 10 seconds of the first press. This will register the code. 26 / 31
6.When registration is completed, the code registration monitor request is output (all doors locked and then all doors unlocked). 7.If you are using two or more transmitters or have added a second transmitter, the next transmitter should be registered within one minute after registering the code for the previous transmitter. The registration procedure is common for all the transmitter. 8.Registration mode will be canceled under the following conditions: When the secret code for four transmitters has been registered; When passing one minute after finishing the registration of all transmitters; When no secret codes have been registered for more than one minute after the registration mode is entered; When the data link connector terminal 1 to ground is disconnected; When the ignition key is removed from the ignition key cylinder; 9.After the registration is completed, carry out the following. Turn the ignition switch to the "LOCK" (OFF) position and then disconnect data link connector terminal 1 from ground. 10.Disconnect data link connector terminal 1 from ground. 11.Remove the ignition key from ignition key cylinder. 27 / 31
12.Close all of the doors. 13.Verify the keyless entry system operates normally. 1.enter the hazard answerback customize mode by observing one of the following steps. If the etacs-ecu enters the customize mode, its tone alarm will sound once. Caution turn the ignition switch to the "lock" (off) position and then connect data link connector terminal 1 to ground. (1)connect the data link connector terminal 1 to ground. (2)close the driver's side door. (3)leave the windshield washer switch on for at least ten seconds. Then the etacs-ecu tone alarm will sound once. 2.if the transmitter "lock" button is pushed consecutively twice within two seconds, the etacs-ecu tone alarm will sound, indicating that the hazard answerback function can be enabled or disabled when the doors are locked. enable the hazard answerback function when the doors are locked: The etacs-ecu tone alarm will sound once. 28 / 31
disable the hazard answerback function when the doors are locked: The etacs-ecu tone alarm will sound twice. 3.if the transmitter "unlock" button is pushed consecutively twice within two seconds, the etacs-ecu tone alarm will sound, indicating that the hazard answerback function can be enabled or disabled when the doors are unlocked. enable the hazard answerback function when the doors are unlocked: The etacs-ecu tone alarm will sound once. disable the hazard answerback function when the doors are unlocked: The etacs-ecu tone alarm will sound twice. 4.exit the hazard answerback customize mode by observing one of the following steps. Caution turn the ignition switch to the "lock" (off) position and then disconnect data link connector terminal 1 from ground. (1)disconnect data link connector terminal 1 from ground. (2)turn the ignition switch to position other then "lock" (off), or remove the ignition key. (3)open the driver's side door. Note: 29 / 31
If any operation is not done for at least three minutes after the etacs-ecu has entered the customize mode, the hazard answerback customize mode will be canceled automatically. Enabling/Disabling the hazard answerback function. 1.remove the ignition key. 2. Push the "unlock" button and then push the "lock" button after 4 seconds to 10 seconds. 3.release the "unlock" button and then release the "lock" button within 10 seconds after step 2. The etacs-ecu tone alarm will sound, indicating that the hazard answerback function can be enabled or disabled when the door are unlocked. enable the hazard answerback function when the doors are unlocked: The etacs-ecu tone alarm will sound once. disable the hazard answerback function when the doors are unlocked: The etacs-ecu tone alarm will sound twice. Enabling/disabling the horn answerback function 30 / 31
1.remove the ignition key. 2. Push the "lock" button and then push the "unlock" button after 4 seconds to 10 seconds. 3.release the "lock" or "unlock" button and then release the "unlock" or "lock" button within 10 seconds after step 2. The etacs-ecu tone alarm will sound, indicating that the horn answerback function can be enabled or disabled. enable the horn answerback function*: The etacs-ecu tone alarm will sound once. disable the horn answerback function: The etacs-ecu tone alarm will sound twice. enable the horn answerback function**: The etacs-ecu tone alarm will sound three times. Note: *: The horn will sound if "lock" button is pressed with the doors locked. **: The horn will sound if the doors are locked with the keyless entry system. 31 / 31