ENWARE-ORAS SINGLE LEVER MIXER Installation and Maintenance Instructions

ENWARE-ORAS SINGLE LEVER MIXER Installation and Maintenance Instructions CUBISTA - SLM800 Series VEGA - SLM600 Series VIVA - SLM300A Series I00061_Oct 17 Call 1300 369 273 www.enware.com.au/oras Enware Australia Pty Limited 9 Endeavour Rd Caringbah NSW 2229 Australia Ph: +61 2 8556 4000 Fax: +61 2 8556 4055

contents page page PRODUCT DESCRIPTIONS 2 TECHNICAL DATA 4 INSTALLATION COMPLIANCE 5 BEFORE PROCEEDING WITH INSTALLATION 5 BASIN AND SINK MOUNT TAP 6 INSTALLATION INSTRUCTIONS Fitting of Temperature Indicator Clips 8 (VEGA only) Detaching and Attaching the Lever Handle 8 Temperature Limiter Adjustment 9 Limiting the Flow Rate 9 Spout Swivel Parameters 10 RECESSED SHOWER INSTALLATION 12 PRODUCT COMPONENTS SPARE PARTS CUBISTA 14 VEGA 16 VIVA 18 Spare Parts 20 SERVICE AND MAINTENANCE Troubleshooting 21 Replacing Cartridge 22 Changing Spout Seals 22 Product Warranty for Australia 23 product description Enware-Oras Mixer Taps feature a modern Scandinavian design with smooth, seamless style that incorporates reliable technology through decades of experience. These versatile range of robust single lever mixers are made for demanding applications, and makes these mixers brilliant for almost any application. Internally the strong cartridge provides easy control whilst the metallic handle connection and dual fixing points provide improved durability. Renown for its strength and unique design, the Oras cartridge is replaceable and like most of the mixer components, they are available as spare parts for an even longer service life. By sharing a single cartridge type, inventory needs, maintenance costs and complexity are reduced. Features Cartridge with metal connection improves mixer strength and vandal resistance. Temperature colour indicators supplied with Hot/Cold and Warm/Cold. Bright Chrome finish. In-built flow rate limiter for increased water efficiency. Hob-Mount Mixer Concealed flow-controlled aerator technology for a clean look and WELS compliance Dual fixing points to help reduce risk of rotation. Flexible hose with reverse thread into mixer body prevents mixer connection loosening while connecting to water supply. Integral check valve and mesh strainer included for each water supply connection. O-ring surface mount sealing for improved fit and watertightness. In-Wall Shower Mixer The in-wall shower mixer has a concealing wall plate that covers and provides easy access to the operating cartridge. The recess mixer components come complete within a self contained plastic housing that is easy to install and reduces the risk of water leaks within the wall cavity. Supplied with enclosed box for easier installation and servicing. Depth into wall cavity -minimum 65mm to maximum 85mm. Shower mixer is available with bath diverter option. 2 Call 1300 369 273 www.enware.com.au

SLM800 series cubista Oras Cubista has been strongly inspired by cubist art, which seamlessly connects modern style with timelessness. Its modern design with geometrically clear lines can be easily placed in different environments and connects with different interior designs. SLM806 Cubista Basin Mixer SLM806D Cubista Basin Mixer with Extended Lever SLM806L Cubista Basin Mixer with Assist Handle SLM807 Cubista Extended Basin Mixer SLM807D Cubista Extended Basin Mixer with Extended Lever Handle SLM807L Cubista Extended Basin Mixer with Assist Handle SLM808 Cubista Shower Mixer SLM809 Cubista Sink Mixer with Gooseneck Spout SLM810 Cubista Shower Mixer with Diverter SLM600 series vega The Oras VEGA single-lever mixer incorporates a full range of commercial quality products to suit any application. Specifically designed to suit health and aged care environments, it has clear visual coloured temperature indication and modern aesthetics to suit. SLM606 Vega Basin Mixer SLM606D Vega Basin Mixer with Extended Lever Handle SLM606ES Vega Basin Mixer with Extended Spout SLM606ESD Vega Basin Mixer with Extended Spout and Extended Lever Handle SLM607 Vega Sink Mixer SLM607D Vega Sink Mixer with Extended Lever Handle SLM608 Vega Shower Mixer SLM608L Oras Shower Mixer with Assist Handle SLM609 Vega Sink Mixer with Gooseneck Spout SLM609D Vega Sink Mixer with Gooseneck Spout and Extended Lever Handle* SLM610 Vega Shower Mixer with Diverter * Note: For SLM609D model, the spout may interfere with the handle when turned on, depending on the position of handle and spout. The spout base can be turned to adjust the position and orientation of spout to avoid interference. www.enware.com.au Call 1300 369 273 3

SLM300 series viva The new Oras VIVA single-lever mixer, with its modern design, successfully incorporates reliable technology developed through decades of experience. The easy to use Viva series provides all the reliability, durability and easy water control you would expect from an Oras mixer at an economical price. SLM306A Viva Basin Mixer SLM306AD Viva Basin Mixer with Extended Lever Handle SLM307A Viva Sink Mixer SLM308A Viva Shower Mixer SLM309A Viva Sink Mixer with Gooseneck Spout SLM310A Viva Shower Mixer with Bath Diverter technical data Inlet Connection Static Inlet Pressure Recommended Working Pressure Range* Flow Rate 15mm (1/2 BSP) 50-1000 kpa Maximum 1600kPa for testing purposes only 50-500 kpa (* In accordance with AS/NZ3500) Hot and cold water inlet pressures should be balanced 8.0 L/min (3 Star WELS standard) 6.2 L/min (4 Star WELS products with code -4 ) 5.0 L/min (5 Star WELS products with code -5 ) 3.4 L/min (6 Star WELS products with code -6 ) Operating Temperature Range 0-80 C Recommended Maximum Temperature** Hob Mount Tap Basin / Sink Cut Out Size Maximum Bench Thickness Basin Mixer Maximum Bench Thickness Sink Mixer In-Wall Shower Body Wall Depth 50 C for residential 45 C for Healthcare & Accessible Design (AS3500) 33 35 mm diameter 30mm (60mm with optional extension) 40mm (70mm with optional extension) Min 65 Max 85 mm from finished wall For use with potable water only. The more stars the more The more stars the more The more stars the more The more stars the more water efficient water efficient water efficient water efficient WATER RATING www.waterrating.gov.au WATER RATING www.waterrating.gov.au WATER RATING www.waterrating.gov.au WATER RATING www.waterrating.gov.au litres per 4 minute litres per 5.5 minute litres per 6.5 minute litres per 8 minute WM40054 4 Call 1300 369 273 www.enware.com.au

installation compliance Enware products are to be installed in accordance with the Plumbing Code of Australia (PCA), AS/NZS3500 and the manufacturer s instructions. Installations not complying with PCA, AS/NZS 3500 or the manufacturer s instructions may void the product and performance warranty provisions. This product must be installed and commissioned by a qualified plumber. The following clauses must be observed for a compliant installation and correct operation of Enware tapware. WATER SERVICES Plumbing Code of Australia: Part B1 Cold Water Services AS / NZS 3500.1-2003 Water Services; Section 1.6(a) Facilities for people with Disabilities Section 3.3.2 Pressure at outlets (min 50kPa) Section 3.3.4 Maximum pressure within buildings (500kPa static) Section 3.4 Velocity Requirement (Max 3.0m/s) Section 16 Testing and Commissioning; Flushing, Hydrostatic testing, cleaning and disinfection of water services. HEATED WATER SERVICES Plumbing Code of Australia: Part B2 Heated Water Services AS / NZS 3500.4-2003 Heated Water Services; Section 1.9 Water Temperature 1.9.1 Storage Temperature 1.9.2 Sanitary fixtures delivery temperature 1.9.3 Acceptable solutions for control of delivery temperatures Section 10 Heated Water Services for People with Disabilities Section 11 Testing and Commissioning ** Heated Water Supply AS/NZS 3500.4: All heated water installations for sanitary fixtures used primarily for personal hygiene purposes shall deliver heated water at a temperature not exceeding: a) 45 C for healthcare and aged care buildings, early childhood centres, primary and secondary schools and nursing homes, or similar facilities for the aged, the sick, children, or people with disabilities; and b) 50 C for all other situations (Laundries and kitchen sinks are not required to have heated water at a maximum of 50 C) For shower mixers with a flexible hose outlet: Where required, an appropriate backflow prevention device must be installed before a shower hose, according to the cross-connection hazard rating as per AS/NZS 3500. (e.g. in situations where a shower hose is installed over a bath, the shower outlet is installed at a low height, or a shower hose is long enough to reach the floor, bidet or a WC pan.) Refer to AS3500.1 - Section 4. before proceeding with installation Before proceeding with installation, ensure all operating and dimensional specifications are suitable for the intended installation. All supply lines must be flushed thoroughly to remove debris prior to the installation of this product, as per AS/NZS 3500.1. Strainers (40 mesh) are recommended if debris is an ongoing problem. A Pressure reduction valve may be required to comply with the recommended maximum supply pressure and/or balanced pressure requirements. It is recommended that isolation valves are installed on both hot and cold supplies prior to the tap and that these are easily accessible. For basin mixers, the maximum bench thickness is 30mm. (With optional extension (part SLMS609) - maximum bench thickness is 60mm.) Bench drill hole size: 33-35mm. For sink mixers, the maximum bench thickness is 40mm. (With optional extension (part SLMS609) - maximum bench thickness is 70mm.) Bench drill hole size: 33-35mm. Recessed shower mixers minimum wall thickness required is 65mm; maximum 85mm from finished wall. www.enware.com.au Call 1300 369 273 5

installation instructions basin and sink CAUTION - REVERSE THREAD FITTING OF FLEXIBLE HOSES INTO MIXER BODY 1. If the tap hole needs to be drilled out of bench or sink, drill a hole with size 33-35mm diameter. Note maximum bench thickness (Basin mixer: 30mm, sink mixer: 40mm, optional extension adds +30mm). 2. Place base sealing washer / O-ring on the base of tap body and press firmly. SEE IMAGE 1 3. Feed the flexible hoses through the hole in the basin/ sink, and position the tap on the basin/ sink. SEE IMAGE 1 Base sealing washer Ensure sealing washer sits flat between basin and base of mixer IMAGE 1 fixing plate fixing nuts Place fixing plate over screws and secure using Fixing nut 4. Align the angle and position of the spout and handle in relation to the basin/ sink. Ensure sealing washer is positioned flat between the basin/ sink surface and the mixer base. NOTE: For additional support for a sink mixer, the Supporting Plate (SLMS608) can be used between the underside of the sink and the fixing plate. E.g. for stainless steel sinks. SEE IMAGE 2 5. Place the Fixing Plate onto the Fixing Screws and put the Fixing Nuts on. Hand tighten the fixing nuts up to press the fixing plate against the underside of the basin. 6. Check the mixer position and alignment again and tighten the nuts up further to secure the mixer onto the basin/sink. Do not over-tighten. NOTE: NOTE: Do not use the handle to align mixer in centre position after tightening the fixing bolt nut. To align the tap, loosen fixing nuts first. If there is any gap in the tap base because of uneven basin/sink surfaces, apply a small bead of silicone sealant to seal the gap and to prevent water leaking through the tap hole. IMAGE 2 ø 33-35 max 40 ( basin: max 30 ) * Image shows sink mixer model Optional Supporting Plate SLMS609 ( max 70, basin: max 60 ) 6 Call 1300 369 273 www.enware.com.au

7. Screw on the G3/8-1/2 Adaptors to the Hot and Cold Outlets, ensuring the Mesh strainer is in position between the Outlet and Adaptor. 8. Connect the flexible hoses to the G3/8-1/2 Adaptors that are now connected to the water supply outlets. Make sure the hot water is connected to the hot water hose. Flexible hoses should be connected directly to isolation valves installed at this position. NOTE: Do not twist or kink the flexible hose. Do not bend the flexible hose beyond its limit. Maximum radius it can bend to is 30mm, and the hose is not to deform more than 15% of its width. SEE IMAGE 3 CAUTION: Reverse thread fitting of flexible hoses into mixer body.! F-Model Oval<15% R R>30mm IMAGE 3 9. Turn water on and test for leaks. Test the mixer tap and check for correct operation. 10. Limits on lever positions for maximum flow and maximum hot water temperature can be adjusted if required. Refer to Temperature Limiter Adjustment and Flow Limiter Adjustment, on page 9. 11. The angle of spout swivel can be adjusted on some models if required. SEE SPOUT SWIVEL PARAMETERS ON PAGE 10. www.enware.com.au Call 1300 369 273 7

FITTING OF TEMPERATURE INDICATOR CLIPS (VEGA MODELS ONLY) 1. Select the correct coloured Temperature Indicator Clips for the specific application out of the 3 colours provided in the pack. The pack should contain 1 blue (cold water) indicator for the right hand side and 1 yellow (warm water)and 1 red (hot water) for the left hand side. 2. Push the two selected indicators together ensuring the leading edge of the left hand side indicator snaps tight within the right hand side one. SEE IMAGES 4 and 5. 3. Place the snap fit connector on the underside of the indicator clips onto the cylindrical lug which is centrally located inside the void in the back of the handle. Once connected, press down firmly so the back of the clips fit within the handle void. It is a firm fit so the clips are difficult to remove by vandals when installed. SEE IMAGES 6, 7 and 8 4. To remove the Temperature Indicator clips, first remove the lever handle (see instructions below) and using a flat head screw driver, lever them off from the underside of the handle against the end of the stem sleeve. IMAGE 4 IMAGE 5 IMAGE 6 IMAGE 7 IMAGE 8 IMAGE 9 IMAGE 10 IMAGE 11 IMAGE 12 IMAGE 13 DETACHING /ATTACHING LEVER HANDLE 1. Using a small flat screwdriver, pry off the temperature indicator cover being careful not to scratch the chrome finish on the handle. SEE IMAGE 10 2. Undo the locking screw and detach the lever handle by pulling it up off the cartridge stem. SEE IMAGE 11 3. Place the new handle over the cartridge stem and push down firmly. If using the extended lever handle, place the white plastic Stem Attachment sleeve over the cartridge stem first. Then place the extended handle over the white plastic stem attachment sleeve and press down firmly. SEE IMAGES 12 and 13 4. Secure the handle in place by using the locking screw to fix it to the cartridge stem. 8 Call 1300 369 273 www.enware.com.au

TEMPERATURE LIMITER ADJUSTMENT The temperature of the hot water can be limited by restricting the swing angle of the lever. This can be done without closing the water inlet to the Faucet. 1. Detach the lever handle and covering cap. 2. Detach the black retaining ring on cartridge with screwdriver. SEE IMAGE 14 3. Pull out the regulating shaft with its limiters. White limiter pins have been installed in the factory to numbers 0 and 10-11. SEE IMAGE 15 4. A shift of 1 point limits the lever s swing angle about 30. SEE IMAGE 16 5. To reduce the hot water limit, move the limiter pin facing the front towards increasing numbers, past 11. LIMITING THE FLOW RATE The flow rate of mixer can be mechanically adjusted by winding in Adjustment screw on the brass stem of the cartridge, which limits the travel of the lever handle. This process can be carried out without turning the water supply off, but note that it would be easier to take the handle off at the full open position. 1. Remove the mixer handle by firstly prying off the indicator button from the front of the handle. Use a flat head screwdriver to unscrew the handle locking screw and remove screw, and then handle. 2. Using a small flathead screwdriver, carefully lever the Covering Cap from under its inside edge and remove it from tap body. 3. Now that the cartridge spindle is exposed, locate the small adjusting screw near the bottom of the brass spindle. Use a small flat head screwdriver to turn the screw in to desired flow limit position. SEE IMAGE 17 4. Re-assemble the covering cap, handle and indicator button. IMAGE 14 IMAGE 15 IMAGE 16 IMAGE 17 www.enware.com.au Call 1300 369 273 9

SPOUT SWIVEL PARAMETERS The swivel spout has a pre-set swing angle allowing freedom to rotate but limiting it from travelling past the sink. SLM307A SLM309A SLM607 SLM609 / SLM809 SLM807 Spout restricted to approx. 100 (50 each way). Stopper clip (limiter pin) cannot be cut, but can be removed to make it swivel 360. To set to a smaller swivel angle an optional limiter pin (SLMS618) needs to be installed. See Adjustment of the Spout Swivel Parameters in the following section. Spout swivels 360 degrees. Cannot be restricted. Spout restricted to approx. 100 (50 each way). Stopper clip (limiter pin) cannot be cut, but can be removed to make it swivel 360 degrees. To set to a smaller swivel angle an optional limiter pin (SLMS618) needs to be installed. See Adjustment of the Spout Swivel Parameters in following section. Spout restricted to approx. 120. To set to a smaller swivel angle of 60, an optional spout stopper (SLMS625) needs to be installed. See Adjustment of the Spout Swivel Parameters (Goose Neck Spout) next page. Spout is fixed and cannot be made to swivel. IMAGE 18 IMAGE 19 ADJUSTMENT OF SPOUT SWIVEL PARAMETERS The swivel range can be adjusted on the following models SLM307A / SLM607 Spout s swing angle is factory pre-set to 100. Spout adjustment can be done without closing the water inlet to the faucet. 1. Detach the lever and the cap. 2. Detach the upper collar ring and detach the spout. Use T-Key or a small Allen key to push the limiter s pin at the back of the faucet and simultaneously lift the spout. SEE IMAGES 18 and 19 3. Remove the limiter pin or change it to a new one that has been cut to fit the desired angle. SEE IMAGE 20. See cutting diagrams for corresponding angle required. SEE IMAGE 21 4. Cutting the limiter pin to different sizes you can change the swing angle. 5. Reassemble the faucet SLM609 The Gooseneck spout can be positioned to suit 3 different alignments for the mixer, i.e. the spout at the back or on either side. SEE IMAGE 28 IMAGE 20 IMAGE 21 10 Call 1300 369 273 www.enware.com.au

SLM809 Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Base cannot be rotated, only the spout swivel angle can be changed. (Steps 2-4 are not applicable) Using the Service key or a small Allen key, push to disengage the Spout locking clip and pull out Gooseneck spout. SEE IMAGE 22 & 23 Using a service key or an Allen key, loosen Allen key locking grub screw on mixer body. SEE IMAGE 24 Rotate mixer body to its desired position. SEE IMAGE 25 Secure mixer body into position using Allen key grub screw on Mixer body At the base of the Gooseneck Spout, locate the removable locking device and pull out using pliers. SEE IMAGE 26 Rotate the spout locking device so it allows the Gooseneck spout to swing within its desired position. IMAGE 28 (If a smaller swivel angle (60 ) is required, use optional part SLMS625) Push Gooseneck spout into mixer body untill locking clip engages. IMAGE 27. If spout does not have the desired swing angle, repeat steps 1, 5 6 & 7 until correct IMAGE 22 IMAGE 23 IMAGE 24 IMAGE 25 IMAGE 26 IMAGE 27 SLMS616 3 mm IMAGE 28 www.enware.com.au Call 1300 369 273 11

installation instructions recessed shower IN-WALL BODY COMPONENT 1. Isolate water supply before commencing installation. Ensure plumbing lines are flushed prior to installation as debris in cartridge will void warranty. The Shower Box has a protective cover which should be left on until the wall is finished. IMAGE 29 2. Secure the Shower Box to the internal cavity within the wall. The Shower Box can be fixed to a masonry wall or wall frame by using the fixing lugs on the side of the box and four screws suitable for the fixing method. When mounting the Shower Box on the wall, take note of the dimensions shown so that the nogging is correctly positioned and takes into account the thickness of the finished wall. IMAGE 29 Wall depth: min 60mm max 85mm from finished wall surface. Finished wall markings are indicated on the side of shower box. This shower cannot be installed sideways, or upside down. The mixer body must be installed in the correct direction, with the shower & bath outlets aligned in the vertical plane to ensure the handle points downwards. The handle can only be installed in one way once the mixer body is installed the handle cannot be flipped upside down or sideways contrary to the mixer body in wall. For shower models the body is supplied with the bath outlet already plugged off by a plug fitted in the bath diverter housing. SEE IMAGE 30 A check valve is fitted on the shower outlet of the mixer. However this is does not qualify as a backflow prevention device. Where required, the installer must install an appropriate backflow prevention device before a shower hose according to the crossconnection hazard rating. (E.g. in cases where a shower hose is installed over a bath, the shower outlet is installed at a low height, or a shower hose is long enough to reach the floor, bidet or a WC pan.) Refer to AS3500.1 - Section 4. For dual check valve shower outlet, use Enware Part SP267 Wall Elbow with Dual Check from Enware. MIXED WATER OUTLET HOT INLET OPTIONAL BATH OUTLET (NORMALLY PLUGGED) COLD INLET PLUG (CAN BE TAKEN OUT FOR OPTIONAL BATH DIVERTER) IMAGE 30 85 60 min. 85 max. 35-60 ø 52 3. Connect water supply to the hot and cold inlets. The hot inlet connector is marked with a red sticker on the Shower box. 4. Connect the mixer shower outlet to the riser leading to shower rose/outlet. 4 IMAGE 31 WARNING: Heat must not be applied to the inlets and outlet of the mixer as this will result in damage to the cartridgend void the warranty. 1 For showers with bath diverter option first, take off the protective cover of Shower Box, take the plug out of the diverter housing on the body (the hex part just below cartridge. SEE IMAGE 31 and 32, then install the diverter assembly in its place. Make the plumbing connection to the bath outlet. 2 IMAGE 32 12 Call 1300 369 273 www.enware.com.au

5. Turn on water to the mixer and test for leaks. Take off the protective cover and loosely place lever handle on stem of mixer cartridge to test the outlet line.( For models with bath diverter option, test the diverter function as well.) Maximum static pressure - 1600 kpa for pressure testing purposes only. 1 2 FIT-OFF FACIA AND HANDLE 6. After the wall is finished, remove the protective front cover from Shower Box. 7. Trim the Shower Box so it is flush with the finished wall, using a sharp utility knife. SEE IMAGE 33 8. Seal any gaps between the wall cut-out and Shower Box with appropriate silicone sealant. SEE IMAGE 33 9. Firmly slide Cartridge Sleeve over mixer body and press, until it clicks into position. Then fit Covering Cap onto top edge of the mixer body. 10. Press the Cover plate over the Cartridge Sleeve and push firmly against the wall. Secure in place using the 2 Allen key fixing screws provided. SEE IMAGE 34 11. Position lever handle onto the cartridge stem. Place the screw through the hole under the handle lever, and tighten to fix the handle in place. SEE IMAGE 32 (previous page) Refer to following sections for instructions on fitting the handle and optional settings: Fitting of Temperature Indicator Clips (VEGA models) - Page 8 Detaching and Attaching the Lever Handle - Page 8 Temperature Limiter Adjustment - Page 9 Limiting the Flow Rate - Page 9 12. Push in the Temperature indication cover onto handle. Align the hot/warm and cold correctly. 13. Turn water on and test for leaks. 14. Test the mixer tap and check for correct operation. Test for correct water temperature (AS3500.4). 15. For models with a Bath Diverter, screw on the push button onto the diverter stem. Test for correct diverter operation. IMAGE 33 IMAGE 34 IMAGE 35 www.enware.com.au Call 1300 369 273 13

product components and spare parts cubista 7. 11. 12. 1. 6. 3. 5. 4. 2. 10. SLM806 PARTS 1 8L/M Aerator SLMS643 2 Fixing plate with nuts SLMS605 3 Cartridge Fixing nut SLMS606 4 Fixing screw (10-pack) SLMS613 5 Oras Cartridge SLMS690 6 Cubista Covering Cap -Basin SLMS641 7 Enware Cubista Lever Handle SLMS638 8 Check valve x 2 ENMS213 9 G3/8-G1/2 Adaptor /Mesh Strainer SLMS611 10 SPEX - Flexible Hoses (Pair) SLMS612 11 Indicator cover - Red/Blue SLMS635 12 Indicator Cover - Yellow/Blue SLMS642 8. 9. 7. 11. 12. 1. 6. 3. 5. 4. 2. 10. 8. SLM807 PARTS 1 8L/M Aerator SLMS643 2 Fixing plate with nuts SLMS605 3 Cartridge Fixing nut SLMS606 4 Fixing screw (10-pack) SLMS613 5 Oras Cartridge SLMS690 6 Cubista Covering Cap -Basin SLMS641 7 Enware Cubista Lever Handle SLMS638 8 Check valve x 2 ENMS213 9 G3/8-G1/2 Adaptor /Mesh Strainer SLMS611 10 SPEX - Flexible Hoses (Pair) SLMS612 11 Indicator cover - Red/Blue SLMS635 12 Indicator Cover - Yellow/Blue SLMS642 9. 14 Call 1300 369 273 www.enware.com.au

product components and spare parts cubista SLM809 PARTS 15. 1. 11. 12. 3. 5. 14. 7. 6. 17. 18. 16. 4. 13. 2. 10. 8. 9. 1 8L/M Aerator SLMS620 2 Fixing plate with nuts SLMS605 3 Cartridge Fixing nut SLMS606 4 Fixing screw (10-pack) SLMS613 5 Oras Cartridge SLMS690 6 Cubista Covering Cap -Basin SLMS641 7 Enware Cubista Lever Handle SLMS638 8 Check valve x 2 ENMS213 9 G3/8-G1/2 Adaptor /Mesh Strainer SLMS611 10 SPEX - Flexible Hoses (Pair) SLMS612 11 Indicator cover - Red/Blue SLMS635 12 Indicator Cover - Yellow/Blue SLMS642 13 Extension Fixing Kit (pair) SLMS609 14 Support Plate SLMS608 15 Cubista Gooseneck Spout SLMS639 16 Gooseneck Spout Sealing Kit SLMS616 17 GN Spout Overturning stopper 120 SLMS624 18 GN Spout Overturning Stopper 60 /0 SLMS625 8 5 SLM808 PARTS 3 4 1 Cartridge Fixing Nut SLMS606 2 Oras Cartridge SLMS690 3 Covering Cap- Cubista SLMS641 4 Enware Cubista Lever Handle SLMS638 5 Cover parts for concealed faucet SLMS626 6 Indicator cover - Red/Blue SLMS635 7 Indicator cover - Yellow/Blue SLMS642 8 Facia and handle only SLM808AP 6 ; 7 2 1 www.enware.com.au Call 1300 369 273 15

product components and spare parts vega Vega Lever Handle Temperature Indication cover Cartridge Fixing nut Temperature indication clips Covering Cap-Basin Oras Cartridge SLM606 PARTS 8L/M Aerator Fixing plates with nuts Cartridge Fixing nut Fixing screw (10-pack) SLMS643 SLMS605 SLMS606 SLMS613 Oras Cartridge SLMS690 Aerator Washer set - Basin Fixing screw Covering Cap -Basin Vega Lever Handle SLMS600 SLMS695 Base Washer set -Basin (10 pack) SLMS601 Fixing plates with nuts G3/8-G1/2 Adaptor /Mesh Strainer SLMS611 SPEX - Hoses Adaptor /Mesh Strainer SPEX Flexible Hoses (Pair) Temperature indication cover (hot/cold) Temperature indication cover (warm/cold) Temperature indicator clips (hot/warm/cold) SLMS612 SLMS635 SLMS642 SLMS621 14 7 17 3 13 4 16 2 5 1 8 10 10 11 12 15 6 9 18 17 SLM607 PARTS 1 1 Vega Lever Handle SLMS695 2 Cartridge Fixing nut SLMS606 3 X-sealing set (2x spout lip seal rings/ grease pack) SLMS607 4 Supporting plate SLMS608 5 Oras Cartridge SLMS690 6 Extension screw kit (pair) SLMS609 7 Spout SLMS614 8 Sink Covering cap SLMS602 9 Fixing plate with nuts SLMS605 10 Spout Retaining Clip (each) SLMS615 11 Spout overturning stopper 100º SLMS617 12 Spout overturning stopper 40-80º SLMS618 13 Sink Base Washer (10 pack) SLMS610 14 Aerator 8 L/M SLMS620 15 Fixing screw (10-pack) SLMS613 16 SPEX Flexible Hoses (pair) SLMS612 17 Temp Indicator Clips (hot/warm/cold) SLMS621 18 G3/8-G1/2 Adaptor/strainer SLMS611 16 Call 1300 369 273 www.enware.com.au

product components and spare parts vega 7 14 2 5 10 10 3 4 16 17 1 8 11 12 19 15 13 6 9 18 SLM609 PARTS 1 Vega Lever Handle SLMS695 2 Cartridge Fixing nut SLMS606 3 X-sealing set (2x Spout lip seal rings/grease kit) SLMS607 4 Supporting plate SLMS608 5 Oras Cartridge SLMS690 6 Extension screw kit (pair) SLMS609 7 Gooseneck Spout SLMS619 8 Sink Covering cap SLMS602 9 Fixing plate with nuts SLMS605 10 Spout Retaining Clip (each) SLMS615 11 G/N Spout overturning stopper:120 SLMS624 12 G/N Spout overturning stopper:60-0 SLMS625 13 Sink Base Washer (10 pack) SLMS610 14 Aerator 8 L/M SLMS620 15 Fixing screw (10-pack) SLMS613 16 SPEX Flexible Hoses (pair) SLMS612 17 Temperature Indicator Clips (hot/warm/cold) SLMS621 18 G3/8-G1/2 Adaptor/strainer SLMS611 19 Gooseneck Spout sealing kit SLMS616 SLM608 & SLM610 PARTS 9 3 8 3 1 Cartridge Fixing Nut SLMS606 2 Oras Cartridge SLMS690 3 Covering Cap SLMS600 4 Vega Lever Handle SLMS695 5 Cover parts for concealed faucet w/ Diverter (SLM610) SLMS640 6 Temperature Indicator clips (hot/warm/cold) SLMS621 7 Oras Diverter Cartridge SLMS634 8 Cover parts for concealed faucet (SLM608) SLMS626 9 Facia and handle only SLM608AP 10 Facia and handle only (with diverter) SLM610AP 6 2 7 1 10 4 5 www.enware.com.au Call 1300 369 273 17

product components and spare parts viva 7. 11. 12. 1. 6. 3. 5. 4. 8. 2. 10 SLM306A PARTS 1 8L/M Aerator SLMS643 2 Fixing plates with nuts SLMS605 3 Cartridge Fixing nut SLMS606 4 Fixing screw (10-pack) SLMS613 5 Oras Cartridge SLMS690 6 Covering Cap -Basin SLMS600 7 Enware Viva Lever Handle SLMS636 8 Base Washer set -Basin (10 pack) SLMS601 9 G3/8-G1/2 Adaptor /Mesh Strainer SLMS611 10 SPEX Flexible Hoses (pair) SLMS612 11 Indicator cover - Red/Ble SLMS635 12 Indicator Cover - Yellow/Blue SLMS642 9. SLM307A PARTS 7. 11. 12. 1. 17. 18. 14. 10. 6. 3. 5. 15. 16. 4. 8. 13. 2. 9. 1 8L/M Aerator SLMS620 2 Fixing plates with nuts SLMS605 3 Cartridge Fixing nut SLMS606 4 Fixing screw (10-pack) 892345 SLMS613 5 Oras Cartridge SLMS690 6 Covering Cap -Sink SLMS602 7 Enware Viva Lever Handle SLMS636 8 Washer - Sink Base (10 pack) SLMS610 9 G3/8-G1/2 Adaptor /Mesh Strainer SLMS611 10 SPEX Flexible Hoses (pair) SLMS612 11 Indicator cover - Red/Blue SLMS635 12 Indicator Cover - Yellow/Blue SLMS642 13 Extension Fixing Screw Kit (pair) SLMS609 14 Sink Support Plate SLMS608 15 Spout overturning stopper 100* SLMS617 16 Spout overturning stopper 40-80 SLMS618 17 Spout Retaining Clip (each) SLMS615 18 X - Sealing Set (2x Spout lip seal rings/grease pack) SLMS607 18 Call 1300 369 273 www.enware.com.au

product components and spare parts viva 1, 7. 11. 12. 6. 3. 5. 10. 2. 4.. 8. SLM309A PARTS 1 8L/M Aerator SLMS620 2 Viva Gooseneck Spout SLMS637 3 Cartridge Fixing nut SLMS606 4 Spout sealing oring set SLMS645 5 Oras Cartridge SLMS690 6 Covering Cap SLMS600 7 Enware Viva Lever Handle SLMS636 8 Fixing Plate and nuts SLMS644 9 G3/8-G1/2 Adaptor /Mesh Strainer SLMS611 10 SPEX Flexible Hoses (pair) SLMS612 11 Indicator cover - Red/Blue SLMS635 12 Indicator Cover - Yellow/Blue SLMS642 9. 8 5 SLM308A PARTS 1 Cartridge Fixing Nut SLMS606 3 6 ; 7 4 2 Oras Cartridge SLMS690 3 Covering Cap SLMS600 4 Enware Viva Lever Handle SLMS636 5 Facia Plate Only SLMS626 6 Indicator cover - Red/Blue SLMS635 7 Indicator cover - Yellow/Blue SLMS642 8 Facia and handle only SLM308AP 1 2 www.enware.com.au Call 1300 369 273 19

spare parts Cartridge SLMS690 Oras Cartridge Key SLMS622 Oras T Service Allen Key 3mm SLMS631 Oras Cartridge Retaining Nut SLMS606 Handle Cubista SLMS638 Handle Vega SLMS695 Handle Viva SLMS636 Assist Handle SLMS697 Extended Lever Handle Vega for hob mounted taps only. Not suitable for showers. Temperature Indicator Clips for Vega SLMS696 SLMS621 Temperature Indication Cover SLMS635 (Hot/Cold), SLMS642 (Warm/Cold, includes stem attachment for extended lever handle and handle fixing screw) Handle fixing screw 672403 Flexible Hoses SPEX (pair) SLMS612 Aerator 8 L/min SLMS620 3/8 x 1/2 Adaptor with Check Valve & Strainer SLMS611 1/2 Mesh Strainer Only (2 in pack) SLMS629 Fixing Kit SLMS605 Oras Shower In-Wall Body Component Only (includes cartridge and fixing nut) SLM608B 20 Call 1300 369 273 www.enware.com.au

troubleshooting Refer to the following troubleshooting chart for specific problems and solutions. PROBLEM CAUSE RECTIFICATION Leaking from outlet. Water is leaking from top of mixer body. Cartridge is damaged or split. Supply pressures too high. Incorrect installation. Cartridge has debris caught in the mechanism. Locking ring is loose. Mixer body o rings are worn Cartridge seals are worn. Check pressure and install a pressure reduction valve. Replace cartridge. Cartridge locking ring has been over tightened. Replace cartridge. Remove cartridge and inspect. Remove debris and/or replace cartridge if damaged. Install an inline strainer Check cartridge bottom seal and tighten cartridge locking ring. Replace cartridge. Water is not flowing from tap. Water turned off. Turn water on. Water comes on when handle is pressed down. Hot water flows when handle is turned anti clockwise. Flexible inlet hose connector does not unscrew. Aerator or Flow control is blocked by debris. Mixer has been installed around the wrong way. Hot and cold connections are incorrect. Hose is turned in the wrong direction. Remove aerator and flow control from spout and clean debris. Install an inline strainer. Loosen locking nut and disconnect flexible hoses from supply. Turn mixer body 180 degrees. Reconnect supply and reposition handle correctly. Reconnect hot and cold supply correctly to mixer. Reverse thread onto mixer body. To unscrew, turn the hose connector clockwise. CLEANING Enware Product should be cleaned with a soft damp cloth using only mild liquid detergent or soap and water. Do not use cleaning agents containing a corrosive acid, scouring agent or solvent chemicals. Do not use cream cleaners, as they are abrasive. Epoxy coated surfaces should only be cleaned with a cloth and clear water or mild detergent. Use of unsuitable cleaning agents may damage the surface. Any damage caused in this way will not be covered by warranty. www.enware.com.au Call 1300 369 273 21

REPLACING CARTRIDGE The cartridge is a non serviceable part. A new cartridge must be used if the existing cartridge is damaged. 1. Turn water supply off and turn mixer handle on to drain water from fitting as much as possible. 2. Remove the mixer handle by firstly prying off the indicator button from the front of the handle. Use a flat head screwdriver to unscrew the handle locking screw and remove screw, and then handle. SEE IMAGE 10, 11 (page 8) 3. Using a small flathead screwdriver, carefully lever the Covering Cap from under its inside edge and remove it from tap body. 4. Locate the Oras Cartridge Socket or suitable 38mm Socket wrench on the flats of the cartridge fixing nut, unscrew the fixing nut and remove. SEE IMAGES 36 and 37 5. Pull up vertically on the stem of the cartridge until the seal is released. Remove the cartridge from the mixer body. SEE IMAGE 38 6. Inspect & replace as per trouble shooting chart & spare parts list. IMAGE 36 IMAGE 37 REASSEMBLING 1. Firmly press the cartridge into the tap body. Ensure bottom seal of cartridge is positioned correctly and when the cartridge is located in the mixer body that the locating lugs align correctly. 2. Screw cartridge fixing nut into mixer body and tighten using the Cartridge key or 38mm socket wrench. 3. Push on the Covering Cap so the black clips secure it against the tap body. 4. Position lever handle onto the cartridge stem. With the screw in place tighten the screw to secure the lever handle. 5. Push in the indicator button. 6. Turn water on and test for leaks. For specific problems such as a leaking tap refer to the trouble shooting guide for instructions. Spare part kits should be on hand before any complete service of the tap is undertaken. CHANGING SPOUT SEALS When kitchen faucet is leaking below or above the spout sleeve, the spout seals need to be replaced. Use Enware part SLMS607 (X-sealing set - 2x spout lip seal rings & grease pack). This can be done without closing the water inlet to the faucet. SEE IMAGE 39 1. Detach the lever and the cap. 2. Detach upper collar ring and detach the spout. 3. Remove old seals, be careful not to damage the sealing grooves in the faucet body. 4. Dry up and clean the grooves in the body and spout sleeve carefully with abrasive cloth. SEE IMAGE 40 5 Lubricate the sealings and put them on the body. 6. Reassemble the faucet. IMAGE 38 IMAGE 39 IMAGE 40 Seals in SLM609 Gooseneck Sink mixer are similar to SLM607 sink mixer pictured. 22 Call 1300 369 273 www.enware.com.au

product warranty for Australia Effective 1 September 2014 Enware Australia Pty Limited (ACN 003 988 314) ( we or us ) warrants that this product (also referred to as our goods ) will be free from all defects in materials and workmanship for 24 months* from the date of purchase. Our liability under this warranty is limited at our option to the repair or replacement of the defective product or part, the cost of repair of the defective product or part or the supply of an equivalent product or part, in each case if we are satisfied the loss or damage was due to a defect in the materials or workmanship of the product or part. All products must be installed in accordance with the manufacturer s instructions, the PCA, and AS/NZS3500 including any other applicable regulatory requirements. making a claim To make a claim under this warranty you must notify us in writing within 7 days of any alleged defect in the product coming to your attention and provide us with proof of your purchase of the product and completed the Online Product Service and Warranty Form available on website www.enware.com.au. All notifications and accompanying forms must be sent to us marked for the attention of the Enware Australia Pty Limited, 9 Endeavour Road, Caringbah NSW 2229. We can also be contacted by telephone (1300 369 273) or by email (info@enware.com.au). Your costs in making a claim under this warranty, including all freight, collection and delivery costs, are to be borne and paid by you. We also reserve the right at our cost to inspect any alleged defect in the product wherever it is located or installed or on our premises. *Conditional warranty: Jumper Valve Tapware - 2 Years: 1 year parts and labour on the complete assembly then a further 1 year parts only warranty is applicable Ceramic Disc Cartridge Tapware - 10 Years: 10 Year ceramic disc cartridges parts only; 1 Year parts and labour on complete assembly Outlets - 1 Year parts and labour on the complete assembly exceptions This warranty does not apply in respect of any damage or loss due to or arising from: a) Failure by you or any other person to follow any instructions for use (including instructions and directions relating to the handling, storage, installation, fitting, connection, adjustment or repair of the product) published or provided by us; b) Failure by you or any other person responsible for the fitting, installation or other work on the product to follow or conform to applicable laws, standards and codes (including the AS/NZ 3500 set of Standards, all applicable State and Territory Plumbing Codes, the Plumbing Code of Australia and directions and requirements of local and other statutory authorities); or c) Any act or circumstance beyond our control including faulty installation or connection, accident, abnormal use, acts of God, damage to buildings, other structures or infrastructure and loss or damage during product transit or transportation. other conditions Except as provided or referred to in this document, we accept no other or further liability for any damages or loss (including indirect, consequential or economic loss) and whether arising in contract, tort or otherwise. Any benefits available to you under this warranty are in addition to any non-excludable rights or remedies you may have under applicable legislation, including as a consumer under the Australian Consumer Law. To that extent you need to be aware that: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. www.enware.com.au Call 1300 369 273 23