ASMECourseCatalog.

Similar documents
Dominion Energy Questar Pipeline LLC Contractor Covered Task List Last updated 10/3/2017

Enbridge Gas Transmission and Midstream and Enbridge Liquid Pipelines (Express-Platte) Contractor Covered Task List Last updated 8/30/2018

Boardwalk Pipeline Partners, LP Contractor Covered Task List Last updated 9/17/2018

Noble Energy Contractor Covered Task List Last updated 2/20/2019

EnLink Midstream Contractor Covered Task List Last updated 11/8/2017

Energy Transfer Partners LP Contractor Covered Task List Last updated 12/10/2018

Howard Midstream Energy Partners LLC Contractor Covered Task List Last updated 10/11/2013

Appendix A Kinder Morgan Operator Qualification Program List of Covered Tasks - Natural Gas - Part 192 Revised 12/13/2017

Black Hills Energy Contractor Covered Task List Last updated 10/10/2018

Williams Contractor Covered Task List Last updated 11/7/2017

Northern Natural Gas Contractor Covered Task List Last updated 4/26/2018

Columbia Pipeline Group Contractor Covered Task List Last updated 1/8/2018

Epic Consolidated Operations LLC Contractor Covered Task List Last updated 9/6/2018

Energy Transfer Partners LP Contractor Covered Task List Last updated 3/2/2018

Southern Star Central Gas Pipeline Contractor Covered Task List Last updated 8/15/2018

Saddle Butte Rockies Midstream LLC Contractor Covered Task List Last updated 12/6/2017

TransCanada US Contractor Covered Task List Last updated 9/27/2018

DCP Midstream Contractor Covered Task List Last updated 7/11/2018

Appendix B Kinder Morgan Operator Qualification Program List of Covered Tasks Hazardous Liquid Pipelines Part 195 revised 12/12/2017

Appendix B Kinder Morgan Operator Qualification Program List of Covered Tasks Hazardous Liquid Pipelines Part 195 revised 8/24/2018

COVERED TASK Conduct Cathodic Protection Surveys 1 DESCRIPTION ELEMENTS OF TASK 4 PART QUESTION NOTES ABNORMAL OPERATING CONDITIONS

Florida City Gas Contractor Covered Task List

Operator Qualification (OQ) Report

PIPELINE CORROSION CONTROL

PHMSA Office of Pipeline Safety Dave Mulligan Western Region

PROCEDURE EXTRUDED HOT TAP & LINE STOP TEES DESIGN & MANUFACTURING VALIDATION

LIQUID MEASUREMENT STATION DESIGN Class No

PTFE Lined Pipe and Fittings

Operating & Maintenance Manual For Steam Conditioning Valve

SECTION PIPING SPECIALTIES PART 1 GENERAL 1.1 SUMMARY

HOT TAPPING & PLUGGING SOLUTIONS

PRESSURE RELIEF / SURGE ANTICIPATOR CONTROL VALVE

BULLETIN August 2009 PERMASEAL PLUG VALVE. ISO 9001:2008 Certified QMS. SMG Valves A Unit of Southern Manufacturing Group, Inc.

High-Pressure Pipeline Equipment

SECTION DOMESTIC-WATER PACKAGED BOOSTER PUMPS

LAR Training. Series 8000 Pneumatic Safety Shut Off Valves Mark Lampe May,

Routine Compressor Maintenance

Underground Storage Tank Guidance for Commercial Building Inspectors

ElectricCourseCatalog.

Biogas safety control equipment

The Use of Conduction Tracers Vs Bare Tracers Metric Version

SECTION DOMESTIC-WATER PACKAGED BOOSTER PUMPS

AIRCRAFT ENGINE MECHANIC, 8602

FINAL REPORT CATHODIC PROTECTION EVALUATION. 42-Inch Water Transmission Pipeline Contract 1 Station 0+00 to South Texas Water Authority

TRADE EXPERIENCE LOG BOOK CANADIAN PETROLEUM CONTRACTORS ASSOCIATION. Petroleum Mechanic Training & Certification

Highway Crossings - Cased or Uncased

Atmos Energy DOT Report-Distribution Leaks Cause of Leak WTX LA MS CO KS KY M-TX TN VA Total

PRESSURE RELIEF / SUSTAINING CONTROL VALVES

Defender Series. Overfill Prevention Valve. Automatic Shutoff for USTs. Installation, Operation and Maintenance Series

STP-MLD. Installation and Owner s Manual

Broetje-Automation Company Standard Structural component specification for welded parts

LANDFILL GAS ELEVATED (CANDLESTICK) FLARE SYSTEM

GALLI&CASSINA. Plug Valves. Conical

PIGGING PRODUCTS. Capex supply. PIG LAUNCHER and RECEIVER

BUREAU OF STANDARDS. Effective Date: 8/19/2016 Section No. 4. Version: 1.2 Procedure No. 3

FLOAT CONTROL VALVES

TAM International, Inc. QI Visible Magnetic Particle Inspection

KEYSTONE OPTISEAL F14/16-15/17 AND BREWSEAL BUTTERFLY VALVES INSTALLATION AND MAINTENANCE INSTRUCTIONS

Installation, Operation & Maintenance of the In-Line Flame Arrestor Model L76L-UF

STAMANT-Safety Pipe. System Description SMR

FUNDAMENTALS OF INSERTION TURBINE METERS Les Bottoms Thermo Electron Corporation, Flow Systems

LACT MEASUREMENT. Total Head = Or PSI = S.G. 2.31

Yukon Oil Inspection Survey Results and Recommendations

Safety Guidelines. Handling instructions. the swiss power source

ROOTS Meters Series B3 Meter Models 8C175-56M175

MSC Manifolds - DIN for Steam Distribution and Condensate Collection Installation and Maintenance Instructions

Monthly Checklist For Depot

DELUGE VALVE MODEL: SD-DVA TECHNICAL DATA : VALVE OPERATION TRIM DESCRIPTION DESCRIPTION PRESSURE THREADED OPENING

Asset Protection Cathodic Protection Testing of Insulating Joints. Work Instruction No.:

Package Contents Part A (3) I-Beam (1) Base (2) Other parts

Focus Area Level Report Including Knowledge and Skills, and Performance Indicators

Bus and coach engineering technician standard: Employer Occupational Brief

GT-200 GATE VALVES PN16, Screwed end

COMBINATION PRESSURE REDUCING AND SOLENOID SHUTOFF CONTROL VALVES 2.01 COMBINATION RESSURE REDUCING AND SOLENOID SHUTOFF CONTROL VALVE

RULE 448 GASOLINE TRANSFER INTO STATIONARY STORAGE CONTAINERS Adopted (Amended , , , , , ) INDEX

ALTITUDE CONTROL VALVES FOR ONE WAY FLOW

Radiation Safety Requirements for the Use of Non-Medical X- Ray.

IMILV01 Carry out routine light vehicle maintenance

AST REGISTRATION PIPE INSPECTION PE REQUIREMENTS. David D. Bradeson, P.E. Chemung Contracting Corporation

Compressed Natural Gas Vehicle Fuel System Inspection Guidance

TECHNICAL DATA. Table 1: Model F1 Dry Valve Part Numbers and Specifications

COMPANY. Pneumatic Flow Meters Installation, Operating & Maintenance Manual AW-Lake Company. All rights reserved. Doc ID:PNEUMAN082516

Cathodic Protection for AST s. Why is Cathodic Protection Important?

Lorri Grainawi Steel Tank Institute. PA NISTM April 25, 2013 Harrisburg, PA

ONYX VALVE CO MODEL DAO-PFC Installation & Maintenance

SECTION 3.00 WARNING WARNING ENGINE STARTUP AND SHUTDOWN PRESTART INSPECTION

Hydro Plant Risk Assessment Guide

M-22 DUAL FUEL ENGINE

DELUGE VALVE DATA SHEET

CONTENTS. Foreword...iii. 1. Introduction...1

Installation, Operation & Maintenance Manual

LINE STOPPING. Extending and modifying your existing pressurized system while it s under full operating conditions.

Inspection and Maintenance of Flame Arresters

PRESSURE REDUCING CONTROL VALVES

Urea Reactor Height Extension to Increase Capacity

User Guide IM/TORBAR-EN Rev. D. Averaging pitot tubes

A new approach to the results of internal inspection

MODULATING FLOAT CONTROL VALVE

Swing Piston Compressors and Vacuum Pumps

ONYX VALVE CO MODEL DAO-ADA Installation & Maintenance

Transcription:

ASMECourseCatalog www.energyu.org www.midwestenergy.org

ASME Abnormal Operating Conditions... 6 ASME GAS01 Hazards of Natural Gas and Prevention of Accidental Ignition... 6 ASME 0001 Measure Structure-to-Electrolyte Potential... 6 ASME 0011 Conduct Close Interval Survey... 7 ASME 0021 Measure Soil Resistivity... 7 ASME 0031 Inspect and Monitor Galvanic Ground Beds/Anodes... 8 ASME 0041 Installation and Maintenance of Mechanical Electrical Connections... 8 ASME 0051 Installation of Exothermic Electrical Connections... 9 ASME 0061 Inspect or Test Cathodic Protection Bonds... 9 ASME 0071 Inspect or Test Cathodic Protection Electrical Isolation Devices... 9 ASME 0081 Install Cathodic Protection Electrical Isolation Devices... 10 ASME 0091 Troubleshoot In-Service Cathodic Protection System... 10 ASME 0101 Inspect Rectifier and Obtain Readings... 11 ASME 0111 Maintain Rectifier... 11 ASME 0121 Collect Sample for Internal Corrosion Monitoring... 12 ASME 0131 Insert and Remove Coupons/Probes for Internal Corrosion Monitoring... 12 ASME 0141 Visual Inspection for Atmospheric Corrosion... 13 ASME 0151 Visual Inspection of Buried Pipe and Components When Exposed... 13 ASME 0161 Visual Inspection for Internal Corrosion... 13 ASME 0171 Measure External Corrosion... 14 ASME 0181 Measure Internal Corrosion... 14 ASME 0191 Measure Atmospheric Corrosion... 15 ASME 0201 Visual Inspection of Installed Pipe and Components for Mechanical Damage... 15 ASME 0211 Measure and Characterize Mechanical Damage on Installed Pipe and Components... 16 ASME 0221 Inspect, Test and Maintain Sensing Devices... 16 ASME 0231 Inspect, Test and Maintain Programmable Logic Controllers... 16 ASME 0241 Inspect, Test and Maintain Liquid Leak Detection Flow Computers... 17 ASME 0251 Inspection and Testing, Corrective and Preventive Maintenance Overfill Protection Systems... 18 ASME 0261 Inspection and Testing, Corrective and Preventive Maintenance Tank Gauges For Leak Detection... 18 ASME 0271 Prove Flow Meters for Hazardous Liquid Leak Detection... 18 ASME 0281 Maintain Flow Meters for Hazardous Liquid Leak Detection... 19 ASME 0291 Inspect, Test and Maintain Gravitometers/Densitometers for Hazardous Liquid Leak Detection... 20 March 2017 Page 1 of 75

ASME 0301 Manually Opening and Closing Valves... 20 ASME 0311 Adjust and Monitor Flow or Pressure-Manual Valve Operation... 21 ASME 0321 Valve Corrective Maintenance... 21 ASME 0331 Valve-Visual Inspection and Partial Operation... 21 ASME 0341 Valve Preventive Maintenance... 22 ASME 0351 Pneumatic Actuator/Operator Inspection and Testing, Preventive and Corrective Maintenance... 22 ASME 0361 Electric Actuator/Operator Inspection and Testing, Preventative and Corrective Maintenance... 23 ASME 0371 Hydraulic Actuator/Operator Inspection and Testing, Preventive and Corrective Maintenance... 23 ASME 0381 Spring Loaded Pressure Regulating Device-Inspection and Testing, Preventive and Corrective Maintenance... 24 ASME 0391 Pilot Operated Pressure Regulating Device-Inspection, Testing, Preventive and Corrective Maintenance... 24 ASME 0401 Controller Type Pressure Regulating Device - Inspection, Testing, Preventive and Corrective Maintenance... 24 ASME 0411 Spring Loaded Pressure Limiting and Relief Device-Inspection, Testing, Preventive and Corrective Maintenance... 25 ASME 0421 Pilot Operated Pressure Limiting and Relief Device-Inspection, Testing, Preventive and Corrective Maintenance... 25 ASME 0431 Pneumatic Loaded Pressure Limiting and Relief Device-Inspection, Testing, Preventive and Corrective Maintenance... 26 ASME 0441 Compressor Start-Up and Shutdown - Manual... 26 ASME 0451 Pump - Start-up and Shutdown - Manual... 27 ASME 0461 Compressor Preventive Maintenance... 27 ASME 0471 Reciprocating Compressor Inspection, Testing and Corrective Maintenance... 28 ASME 0481 Centrifugal Compressor Inspection, Testing and Corrective Maintenance... 28 ASME 0491 Rotary Compressor Inspection, Testing and Corrective Maintenance... 29 ASME 0501 Pump Preventive Maintenance... 29 ASME 0511 Centrifugal Pump Inspection and Testing and Corrective Maintenance... 30 ASME 0521 Reciprocating Pump Inspection and Testing and Corrective Maintenance... 30 ASME 0531 Rotary Pump Inspection and Testing and Corrective Maintenance... 31 ASME 0541 Screw Pump Inspection and Testing and Corrective Maintenance... 31 ASME-0551 Explosive Atmospheric Detection and Alarm System Performance Test and Corrective Maintenance 32 ASME 0561 Pressure Test Non-Liquid Medium Test Pressure Less Than 100 psi... 32 ASME 0571 Pressure Test Non-Liquid Medium Test Pressure Greater Than or Equal to 100 psi... 33 ASME 0581 Pressure Test Liquid Medium... 33 March 2017 Page 2 of 75

ASME 0591 Leak Test at Operating Pressure... 34 ASME 0601 NDT Radiographic Testing... 34 ASME 0611 NDT Liquid Penetrant Testing... 35 ASME 0621 NDT Magnetic Particle Testing... 35 ASME 0631 NDT Ultrasonic Testing... 36 ASME-0641 Visually Inspect Pipe and Components - Prior to Installation... 36 ASME 0651 Routine Visual Inspection of Breakout Tanks... 37 ASME 0661 Inspection of Breakout Tanks... 37 ASME 0671 Joining of Plastic Pipe Solvent Cement... 37 ASME 0681 Joining of Plastic Pipe Stab Fittings... 38 ASME 0691 Joining of Pipe Non-Bottom Out Compression Couplings... 38 ASME 0701 Joining of Pipe Bottom Out Compression Couplings... 39 ASME 0711 Joining of Pipe Compression Couplings... 39 ASME 0721 Joining of Pipe Threaded Joints... 40 ASME 0731 Joining of Pipe Flange Assembly... 40 ASME 0741 Joining of Copper Pipe - Brazing or Soldering... 41 ASME 0751 Joining of Plastic Pipe Butt Heat Fusion: Manual... 41 ASME 0761 Joining of Plastic Pipe Butt Heat Fusion: Hydraulic Machine... 41 ASME 0771 Joining of Plastic Pipe Sidewall Heat Fusion... 42 ASME 0781 Joining of Plastic Pipe Electrofusion... 42 ASME 0791 Joining of Plastic Pipe Socket... 43 ASME 0801 Welding... 44 ASME 0811 Visual Inspection of Welding and Welds... 44 ASME 0821 Tubing & Fitting Installation Instrument, Control and Sampling... 45 ASME 0831 Cast Iron Caulked Bell and Spigot Joints Installation and Maintenance of Mechanical Leak Clamp(s)... 45 ASME 0841 Cast Iron Joints... 46 ASME 0851 Internal Sealing Cast Iron and Ductile Iron... 46 ASME 0861 Installation of Steel Pipe in a Ditch... 47 ASME 0871 Installation of Steel Pipe in a Bore... 47 ASME 0881 Installation of Steel Pipe Plowing/Pull-in... 47 ASME 0891 Field Bending of Steel Pipe... 48 ASME 0901 Installation of Plastic Pipe in a Ditch... 48 March 2017 Page 3 of 75

ASME 0911 Installation of Plastic Pipe in a Bore... 49 ASME 0921 Installation of Plastic Pipe Plowing/Pull-in... 49 ASME 0931 Installation of Plastic Pipe by Plowing/Planting... 50 ASME 0941 Install Tracer Wire... 50 ASME 0951 Installation of Pipe Above Ground... 51 ASME 0961 Above Ground Supports and Anchors Inspection, Preventive and Corrective Maintenance... 51 ASME 0971 Installation and Maintenance of Casing Spacers, Vents and Seals... 51 ASME 0981 Backfilling... 52 ASME 0991 Coating Application and Repair Brushed or Rolled... 52 ASME 1001 Coating Application and Repair Sprayed... 53 ASME 1011 External Coating Application and Repair Wrapped... 53 ASME 1021 Apply or Repair Internal Coating Other Than By Brushing, Rolling or Spraying... 54 ASME 1031 Install or Repair Internal Liner... 54 ASME 1041 Install Mechanical Clamps and Sleeves Bolted... 55 ASME 1051 Fit-up of Weld Type Repair Sleeve... 55 ASME 1061 Install Composite Sleeves... 55 ASME 1071 Repair of Steel Pipe By Grinding... 56 ASME 1081 Tapping a Pipeline (Tap Diameter 2 Inch and Less)... 56 ASME 1091 Tapping a Pipeline (Tap Diameter Greater than 2 Inch)... 57 ASME 1101 Tapping a Pipeline with a Built-in Cutter... 57 ASME 1111 Tapping Cast and Ductile Iron Pipe, and Low Pressure Steel Pipe... 58 ASME 1121 Bagging and Stopping Low Pressure Pipe... 58 ASME 1131 Stopper (Stopple) Pipe... 59 ASME 1141 Squeeze off Plastic Pipe... 59 ASME 1151 Squeeze off Steel Pipe... 60 ASME 1161 Installation of Customer Meters and Regulators Residential and Small Commercial... 60 ASME 1171 Installing Customer Meters Large Commercial and Industrial... 61 ASME 1181 Installing and Maintaining Customer Pressure Regulating, Limiting, and Relief Device Large Commercial & Industrial... 61 ASME 1191 Maintenance of Service Valves Upstream of Customer Meter... 62 ASME 1201 Temporary Isolation of Service Lines and Service Discontinuance... 62 ASME 1211 Odorization Periodic Sampling... 63 ASME 1221 Odorization Odorizer Inspection, Testing, Preventive and Corrective Maintenance... 63 March 2017 Page 4 of 75

ASME 1231 Inside Gas Leak Investigation... 64 ASME 1241 Outside Gas Leak Investigation... 64 ASME 1251 Hazardous Liquid Leak Investigation... 64 ASME 1261 Walking Gas Leakage Survey... 65 ASME 1271 Mobile Gas Leakage Survey Flame Ionization... 65 ASME 1281 Mobile Gas Leakage Survey Optical Methane... 66 ASME 1291 Locate Underground Pipelines... 66 ASME 1301 Install and Maintain Pipeline Markers... 67 ASME 1311 Inspect Pipeline Surface Conditions Patrol Right of Way or Easement... 67 ASME 1321 Damage Prevention During Excavation Activities By or On Behalf of the Operator... 68 ASME 1331 Damage Prevention Inspection during Third Party Excavation of Encroachment Activities as Determined Necessary by Operator... 68 ASME 1341 Provide or Assure Adequate Pipeline Support during Excavation Activities... 69 ASME 1351 Vault Inspection and Maintenance... 69 ASME 1361 Station Emergency Shutdown System Inspection, Testing and Corrective Maintenance... 70 ASME 1371 Operate Gas Pipeline System Control Center Operations... 70 ASME 1381 Operate Gas Pipeline Local Facility Remote Control Operations... 71 ASME 1391 Operate Liquids Pipeline System Control Center Operations... 71 ASME 1401 Operate Liquids Pipeline Local Facility Remote Control Operations... 72 ASME 1411 Indirect Inspection Techniques... 72 ASME 1421 Direct Examination Techniques... 73 ASME 1631 Launching-Receiving Pigs for Lines Out-of-Service... 73 ASME 1641 Launching-Receiving Pigs for Lines In-Service... 74 ASME 1651 Purging of Flammable or Inert Gas... 74 ASME 1661 Purge: Hazardous Liquids... 75 March 2017 Page 5 of 75

ASME Abnormal Operating Conditions TNG - MEA11519 KNT - MEA11520 This course covers Abnormal Operating Conditions (AOCs) related to equipment and procedures in the pipeline industry. Personnel working on natural gas and hazardous liquid pipelines must be able to identify when an abnormal or potentially hazardous condition exists, and then react appropriately. Identify abnormal pipeline operations vs. abnormal conditions. Recognize and react appropriately to standard pipeline AOCs and anticipated problems. Implement make safe procedures. Properly document and report AOCs and potentially hazardous conditions. ASME GAS01 Hazards of Natural Gas and Prevention of Accidental Ignition TNG MEA11524 KNT MEA11523 Natural gas is a fossil fuel, made up primarily of methane. It may have by-products that include ethane, propane, butanes, pentanes, hydrocarbons, sulfur, and carbon dioxide. It is processed and refined to become a simple, clean burning source of energy to power homes, business, and industry. This course discusses the hazards of natural gas and how to prevent accidental ignition. How natural gas is formed, is extracted and refined, and used. The chemical make-up of natural gas, its properties and behaviors. The potential dangers of natural gas. How to locate and eliminate sources of natural gas ignition on the job site in the event of a gas leak. Procedures and requirements for responding to natural gas leaks. ASME 0001 Measure Structure-to-Electrolyte Potential TNG - MEA11139 KNT MEA1813 PEF MEA1976 March 2017 Page 6 of 75

This course discusses activities associated with using measurement equipment to take a reading of the potential between a pipe or tank and the soil. Performing checks on test equipment. Identifying and locating correct test points. Measuring structure-to-electrolyte potential. Documentation and record keeping. ASME 0011 Conduct Close Interval Survey TNG MEA11140 KNT MEA1814 PEF MEA1977 This course discusses activities associated with gathering electrical potential readings along the pipeline at specified intervals. Performing checks on test equipment. Identifying and locating correct test points. Performing interval surveys. Completing required documentation. ASME 0021 Measure Soil Resistivity TNG MEA11141 KNT MEA1815 PEF MEA1978 This course discusses taking soil resistivity measurements for use in verifying adequate cathodic protection level. Identifying requirements for soil resistivity testing. Identifying and locating correct test points. Taking measurements and recording data. March 2017 Page 7 of 75

Ensuring accuracy of test results. Performing test equipment checks. ASME 0031 Inspect and Monitor Galvanic Ground Beds/Anodes TNG MEA11142 KNT MEA1816 PEF MEA1979 This course discusses activities associated with inspecting and monitoring the electric potential of galvanic groundbeds and anodes. Performing checks on test equipment. Identifying and locating correct test points. Measuring current output of anodes and groundbeds. Maintaining records and documentation. ASME 0041 Installation and Maintenance of Mechanical Electrical Connections TNG MEA11143 KNT MEA1817 PEF MEA1980 In general, all buried steel pipelines require the use of cathodic protection systems as a form of corrosion control. This course discusses requirements for installing and maintaining the electrical connections required for cathodic protection, such as tracer wire, test leads, bonds and shunts. Electrical connection requirements. Checking test equipment. Installing and maintaining electrical connections using mechanical fittings. Verifying mechanical integrity and electrical continuity. March 2017 Page 8 of 75

ASME 0051 Installation of Exothermic Electrical Connections TNG MEA11144 KNT MEA1818 PEF MEA1981 This course discusses making exothermic (e.g., thermite, cadweld and pin-brazing) connections of tracer wire, test leads, bonds, shunts, etc. Exothermic connection requirements. Checking test equipment. Making weld connections. Verifying mechanical integrity and electrical continuity. ASME 0061 Inspect or Test Cathodic Protection Bonds TNG MEA11145 KNT MEA1819 PEF MEA1982 This course discusses the inspection and testing of cathodic protection bonds. For metallic pipelines, bonds are installed across all joints, across any electrically discontinuous connections, and across all other pipe and structures (with other than welded or threaded joints) included in the cathodic protection system. The basics of cathodic protection (CP). Requirements for inspection and testing of CP bonds. Test equipment operation. Recognizing and reacting to abnormal conditions. ASME 0071 Inspect or Test Cathodic Protection Electrical Isolation Devices TNG MEA11146 KNT MEA1820 PEF MEA1983 March 2017 Page 9 of 75

This course discusses activities associated with inspecting and testing of electrical isolation devices used as part of cathodic protection systems for buried pipelines. The basics of cathodic protection. General inspection and testing requirements. Test equipment calibration and operation. Maintaining records and documentation. ASME 0081 Install Cathodic Protection Electrical Isolation Devices TNG MEA11147 KNT MEA1821 PEF MEA1984 Electrical isolation is the condition of being electrically separated from other metallic structures within the environment. It is often necessary to install electrical isolation devices in order to ensure proper cathodic protection of a pipeline. General cathodic protection requirements. Electrical isolation requirements. Installing electrical isolation devices. ASME 0091 Troubleshoot In-Service Cathodic Protection System TNG MEA11148 KNT MEA1822 PEF MEA1985 Cathodic protection systems use electrical current to prevent the corrosion of buried metallic structures. In pipelines, this can prevent rust and deterioration, lowering the risk of dangerous leaks and extending the life of the pipeline. This course discusses requirements and procedures for troubleshooting in-service cathodic protection systems. March 2017 Page 10 of 75

General information on cathodic protection. Inspection and testing requirements. Operating test equipment. Troubleshooting and analyzing test results. ASME 0101 Inspect Rectifier and Obtain Readings TNG MEA11149 KNT MEA1823 PEF MEA1986 This course discusses inspecting the rectifier for damage and deterioration, and obtaining readings as specified. Inspection requirements. Performing test equipment check. Obtaining voltage and current output readings. ASME 0111 Maintain Rectifier TNG MEA11150 KNT MEA1824 PEF MEA1987 Rectifiers are used to convert alternating current to direct current for use in cathodic protection of buried pipelines. This course discusses verification that a rectifier is functioning within specified parameters after it has been hung and AC power applied, prior to (or during) placing in service. This course also discusses actions to repair or replace in-service rectifiers or components. Identifying maintenance requirements. Performing test equipment checks. Testing and troubleshooting procedures. Repair or replacement of defective components. Placing the rectifier in service. March 2017 Page 11 of 75

Adjusting rectifier output. ASME 0121 Collect Sample for Internal Corrosion Monitoring TNG MEA11151 KNT MEA1825 PEF MEA1988 This course discusses the collection and handling of samples (gas, liquid, solids) for internal corrosion monitoring, including preventing contamination of the samples. Types of corrosion. Methods of inspection. Collection methods. Monitoring procedures. ASME 0131 Insert and Remove Coupons/Probes for Internal Corrosion Monitoring TNG MEA11152 KNT MEA1826 PEF MEA1989 This course discusses inserting and removing coupons/probes for internal corrosion monitoring, and preventing contamination or damage of the coupons/probes. Corrosion basics. Coupon preparation. Inserting and removing coupons. Preparing coupons for shipment. March 2017 Page 12 of 75

ASME 0141 Visual Inspection for Atmospheric Corrosion TNG MEA11153 KNT MEA1827 PEF MEA1990 This course discusses the inspection of pipe and pipeline components, exposed to the atmosphere, for the purpose of detecting atmospheric corrosion. The causes and signs of atmospheric corrosion. Monitoring requirements. Visual inspection requirements. ASME 0151 Visual Inspection of Buried Pipe and Components When Exposed TNG MEA11154 KNT MEA1828 PEF MEA1991 This course discusses inspection of buried pipe and pipeline components when exposed for the purpose of detecting external corrosion and evaluating coating integrity. Types of corrosion. Inspecting coating. Inspecting pipe surfaces. ASME 0161 Visual Inspection for Internal Corrosion TNG MEA11155 KNT MEA1829 PEF MEA1992 March 2017 Page 13 of 75

This course discusses inspection of the internal surface of pipe and pipeline components, including tapping coupons, when exposed for the purpose of detecting internal corrosion. Visual inspection requirements. Inspecting protective coating. Inspecting internal pipe surfaces, components and tapping coupons. ASME 0171 Measure External Corrosion TNG MEA11156 KNT MEA1830 PEF MEA1993 This course discusses activities to measure and characterize external corrosion, including investigation to determine the extent of corrosion and recording data. This course applies to buried pipelines; measurement of atmospheric corrosion on aboveground pipelines is covered in a separate course. Identifying various types of corrosion. Corrosion measurement preparation. Taking external corrosion measurements. ASME 0181 Measure Internal Corrosion TNG MEA11157 KNT MEA1831 PEF MEA1994 This course discusses activities to measure and characterize internal corrosion, including investigation to determine the extent of corrosion and recording data. Surface preparation. Performing test equipment check. March 2017 Page 14 of 75

Taking measurements. Identifying characteristics of corrosion. ASME 0191 Measure Atmospheric Corrosion TNG MEA11158 KNT MEA1832 PEF MEA1995 This course discusses activities to measure and characterize atmospheric corrosion, including investigation to determine the extent of corrosion and recording data. Surface preparation. Performing test equipment check. Taking measurements. Identifying characteristics of corrosion. ASME 0201 Visual Inspection of Installed Pipe and Components for Mechanical Damage TNG MEA11159 KNT MEA1833 PEF MEA1996 To reduce the possibility of failure, pipe must be properly inspected. Damage to pipe and its components can occur during installation, accidents, excavation activities, or during routine maintenance. Each length of pipe and each pipe component must be visually inspected at the site of installation to ensure that it has not sustained any visually determinable damage that could impair its serviceability. Exposed pipe must be inspected for evidence of corrosion or manufacturing defects associated with mechanical damage. Visual Inspection of pipe. Visual Inspection of pipeline components. March 2017 Page 15 of 75

ASME 0211 Measure and Characterize Mechanical Damage on Installed Pipe and Components TNG - MEA11160 KNT - MEA1834 PEF MEA1997 This course discusses activities to measure and characterize mechanical damage (e.g. dents, gouges, cracks) on installed pipe and components, including investigation to determine the extent of damage and recording data. Surface preparation requirements. Taking measurements. Characterizing damage. Recording damage. ASME 0221 Inspect, Test and Maintain Sensing Devices TNG MEA11161 KNT MEA1835 PEF MEA1998 This course discusses the proper procedures to locate, inspect, test, maintain, and replace sensing devices such as pressure switches and pressure, temperature, and differential transmitters. Prior knowledge base required. Verifying proper operation prior to or during placing in service. Verifying proper operation after installation. Adjusting sensing device set points and defective components. ASME 0231 Inspect, Test and Maintain Programmable Logic Controllers TNG MEA11162 KNT MEA1836 PEF MEA1999 March 2017 Page 16 of 75

Pipelines transport product that the world needs and are present almost everywhere. Pipelines are controlled by supervisory control and data acquisition systems (SCADA) to provide product and guard against damaging leaks. Programmable Logic Controllers (PLCs) are a component of a SCADA system. PLCs provide dependable and economical high-speed control and monitoring in pipeline applications. This course identifies procedures to inspect, test and maintain PLCs. Remove PLCs from service. Perform test equipment checks. Perform a PLC visual inspection. Perform PLC test and maintenance procedures. Properly return PLC to service. Recognize and react to Abnormal Operating Conditions. ASME 0241 Inspect, Test and Maintain Liquid Leak Detection Flow Computers TNG MEA11163 KNT MEA1837 PEF MEA11000 This course discusses verification that the flow computer, when used in a computational pipeline monitoring leak detection system, is functioning within specified parameters. This includes prior to, during, and after placing the flow computer in service. Procedures for verifying proper functioning of flow computer. Placing flow computer in manual mode. Removing flow computer from service. Visually inspecting flow computer. Procedures to repair or replace flow computers and components. Adjusting flow computer set points. Conducting flow computer performance tests. March 2017 Page 17 of 75

ASME 0251 Inspection and Testing, Corrective and Preventive Maintenance Overfill Protection Systems TNG MEA11164 KNT MEA1838 PEF MEA11001 This course discusses requirements for inspection and testing, corrective and preventive maintenance for overfill protection systems. Inspecting and testing system components. Troubleshooting device failures. Performing preventive and corrective maintenance. ASME 0261 Inspection and Testing, Corrective and Preventive Maintenance Tank Gauges For Leak Detection TNG MEA11165 KNT MEA1839 PEF MEA11002 Tank gauges are an important part of monitoring storage tank inventory in order to detect potentially dangerous leaks. This course discusses inspection, testing, corrective and preventive maintenance of tank gauges used for leak detection. Identifying and performing pre-test procedures. Performing visual, external, and internal inspections of tank gauge systems. Performing preventive and corrective maintenance on tank gauge systems. ASME 0271 Prove Flow Meters for Hazardous Liquid Leak Detection TNG MEA11166 KNT MEA1840 PEF MEA11003 March 2017 Page 18 of 75

Flow meters measure the flow of product moving through a pipe. Measurements are used to analyze the quality and rate of flow. Decrease in flow can indicate problems such as dangerous leaks. Inaccurate flow meters or the failure to take measurements can have serious consequences. Proving is the process for verifying the accuracy of flow meters for leak detection purposes. By comparing known standards to measurements of individual flow meters, workers are able to evaluate a flow meters accuracy and repeatability. Functions and types of flow meters. Factors that affect flow meters. Process and calculations of proving flow meters. Different proving methods of flow meters. Proving flow meter calculations. Proving process notifications. Proving operating parameters, requirements and procedures. Documentation requirements. ASME 0281 Maintain Flow Meters for Hazardous Liquid Leak Detection TNG MEA11167 KNT MEA1841 PEF MEA11004 This course covers verification of flow meters (e.g. line integrity meters) for hazardous leak detection. Flow meters measure the quantity or flow of products moving through a pipe. Their measurements are used to analyze flow quality and flow rates. Drops in flow rate can indicate problems such as dangerous leaks. Inaccurate flow meters or failure to take measurements can have serious consequences. Complete an inspection and performance evaluation of flow meters. Identify conditions out of parameters or specifications. Troubleshoot performance issues and determine proper actions to resolve conditions. Maintain flow meters, including adjusting outputs, repair, or replacement. Recognize and react to abnormal operating conditions. March 2017 Page 19 of 75

ASME 0291 Inspect, Test and Maintain Gravitometers/Densitometers for Hazardous Liquid Leak Detection TNG MEA11168 KNT MEA1842 PEF MEA11005 Gravitometers and densitometers are pipeline industry tools that measure and monitor product density and specific gravity of liquids and gases for many purposes, including hazardous liquid leak detection. The performance of a hazardous liquid leak detection monitoring systems is limited by the accuracy of the instrumentation. To keep leak detection instrumentation such as gravitometers and densitometers in top performance, regular inspection, testing, and maintenance is necessary. Understand operating principles of gravitometers and densitometers. Identify inspection, testing, and maintenance requirements and procedures. Maintaining component(s). Recognize and react to potential problems and abnormal operating conditions (AOC s). ASME 0301 Manually Opening and Closing Valves TNG MEA11169 KNT MEA1843 PEF MEA11006 This course discusses manually opening and closing valves (e.g., pipeline startup and shutdown, flow direction, pigging, tank switching, etc.) at the valve site, either manually or using the valve actuator. Also included is information on valve identification, notifications and pressure verification. This course does not induce operation of valves for adjusting and monitoring flow or pressure or temporary isolation of service lines and service discontinuance. Verifying valve identification. Understanding the procedure for opening and closing valves. March 2017 Page 20 of 75

ASME 0311 Adjust and Monitor Flow or Pressure-Manual Valve Operation TNG MEA11170 KNT MEA1844 PEF MEA11007 This course covers the adjustment of flow or pressure, either manually or using the valve actuator at the valve site. This includes valve identification, notifications and pressure verification. Requirements for flow or pressure adjustment. Valve and segment identification and verification. Manual valve operation for adjusting and maintaining pressure or flow. Notification requirements. ASME 0321 Valve Corrective Maintenance TNG MEA11171 KNT MEA1845 PEF MEA11008 Valves are used extensively in pipeline transmission systems to interrupt, divert, or regulate the flow of product. This course discusses the repair, replacement, alternation or refurbishment of pipeline valves. Identify valve maintenance requirements. Verify valve identification. Perform valve maintenance and lubrication procedures. Recognize and react to abnormal operating conditions. ASME 0331 Valve-Visual Inspection and Partial Operation TNG MEA11172 KNT MEA1846 PEF MEA11009 March 2017 Page 21 of 75

This course discusses visual inspection, partial operation (function test), and lubrication of valves, except for the temporary isolation of service lines and service discontinuance (See ASME-1191). Identify inspection requirements. Verify valve identification. Visually inspect and partially operate valves. Lubricate valves. ASME 0341 Valve Preventive Maintenance TNG MEA11173 KNT MEA1847 PEF MEA11010 This course discusses activities involved with preventive maintenance of valves. Verifying valve identification. Performing preventive maintenance of valves. ASME 0351 Pneumatic Actuator/Operator Inspection and Testing, Preventive and Corrective Maintenance TNG MEA11174 KNT MEA1848 PEF MEA11011 Pneumatic actuators/operators are an important part of successful pipeline operation. They allow for the remote and automatic operation of valves, which is extremely important during a crisis as well as day-to-day work. Therefore, inspection, testing, preventive and corrective maintenance is essential to verify these components are fail safe. March 2017 Page 22 of 75

Understanding actuators. Identifying procedures for inspection, testing, and maintenance. ASME 0361 Electric Actuator/Operator Inspection and Testing, Preventative and Corrective Maintenance TNG MEA11175 KNT MEA1849 PEF MEA11012 Electric actuators/operators are an important part of successful pipeline operation. They allow for the remote and automatic operation of valves, which is extremely important during a crisis as well as day-to-day work. Therefore, inspection, testing, preventive and corrective maintenance is essential to verify these components are fail safe. Understanding actuators. Identifying procedures for inspection, testing, and maintenance. ASME 0371 Hydraulic Actuator/Operator Inspection and Testing, Preventive and Corrective Maintenance TNG MEA11176 KNT MEA1850 PEF MEA11013 Hydraulic actuators/operators are an important part of successful pipeline operation. They allow for the remote and automatic operation of valves, which is extremely important during a crisis as well as day-to-day work. Therefore, inspection, testing, preventive and corrective maintenance is essential to verify these components are fail safe. Understanding actuators. Identifying procedures for inspection, testing, and maintenance. March 2017 Page 23 of 75

ASME 0381 Spring Loaded Pressure Regulating Device-Inspection and Testing, Preventive and Corrective Maintenance TNG MEA11177 KNT MEA1851 PEF MEA11014 This course discusses activities involved with inspection and testing, and preventive and corrective maintenance of spring-loaded pressure regulators. Understanding the importance of regulating pressure in a pressurized pipeline. Understanding the types and components of pressure regulators. Identifying the requirements for inspection and testing, and preventive and corrective maintenance. ASME 0391 Pilot Operated Pressure Regulating Device-Inspection, Testing, Preventive and Corrective Maintenance TNG MEA11178 KNT MEA1852 PEF MEA11015 This course discusses activities involved with inspection and testing, and preventive and corrective maintenance of pilot-operated pressure regulators. Understanding the importance of regulating pressure in a pressurized pipeline. Understanding the types and components of pressure regulators. Identifying the requirements for inspection and testing, and preventive and corrective maintenance. ASME 0401 Controller Type Pressure Regulating Device - Inspection, Testing, Preventive and Corrective Maintenance TNG MEA11179 KNT MEA1853 PEF MEA11016 March 2017 Page 24 of 75

This course discusses activities involved with inspection and testing, and preventive and corrective maintenance of controller type pressure regulators. Understanding the importance of regulating pressure in a pressurized pipeline. Understanding the types and components of pressure regulators. Identifying the requirements for inspection and testing, and preventive and corrective maintenance. ASME 0411 Spring Loaded Pressure Limiting and Relief Device-Inspection, Testing, Preventive and Corrective Maintenance TNG MEA11180 KNT MEA1854 PEF MEA11017 This course discusses activities involved with inspection and testing, and preventive and corrective maintenance of spring-loaded pressure limiting and relief devices. Understanding the importance of regulating pressure in a pressurized pipeline. Understanding the types and components of pressure regulators. Identifying the requirements for inspection and testing, and preventive and corrective maintenance. ASME 0421 Pilot Operated Pressure Limiting and Relief Device-Inspection, Testing, Preventive and Corrective Maintenance TNG MEA11181 KNT MEA1855 PEF MEA11018 This course discusses activities involved with inspection and testing, preventive and corrective maintenance of pilotoperated pressure limiting and relief devices. March 2017 Page 25 of 75

Understanding the importance of regulating pressure in a pressurized pipeline. Understanding the types and components of pressure regulators. Identifying the requirements for inspection and testing, and preventive and corrective maintenance. ASME 0431 Pneumatic Loaded Pressure Limiting and Relief Device-Inspection, Testing, Preventive and Corrective Maintenance TNG MEA11182 KNT MEA1856 PEF MEA11019 This course discusses activities involved with inspection and testing, and preventive and corrective maintenance of pneumatic-loaded pressure limiting and relief devices. Understanding the importance of regulating pressure in a pressurized pipeline. Understanding the types and components of pressure regulators. Identifying the requirements for inspection and testing, and preventive and corrective maintenance. ASME 0441 Compressor Start-Up and Shutdown - Manual TNG MEA11183 KNT MEA1857 PEF MEA11020 Compressors are used to increase the pressure in a gas pipeline, maintain the desired flow of gas through the pipeline and allow gas to flow from a lower pressure pipeline to a higher pressure pipeline. Therefore, compressors are an important part to ensuring pipeline capacity and efficiency. This course reviews pipeline compressors and their drivers and the appropriate activities associated with the manual process of compressor shutdown, removal from service, return to service and startup procedures. Pipeline compressor and driver types. Specifications for manual shutdown and startup of compressor stations. March 2017 Page 26 of 75

Procedures for compressor & driver shutdown, removal from service, return to service and startup. Process for change of compressor status. ASME 0451 Pump - Start-up and Shutdown - Manual TNG MEA11184 KNT MEA1858 PEF MEA11021 Pumps are used to increase the flow or maintain the desired flow of liquids through the pipeline and to allow liquids to flow from a lower pressure pipeline to a higher pressure pipeline. Therefore, pumps are an important part to ensuring pipeline capacity and efficiency. This course reviews pipeline pumps and their drivers and the appropriate activities associated with the manual process of pump startup, removal from service, return to service and shutdown procedures. Pump and driver types. Specifications for manual shutdown and startup of pump stations. Procedures for pump & driver shutdown, removal from service, return to service and startup. Process for change of pump status. ASME 0461 Compressor Preventive Maintenance TNG MEA11185 KNT MEA1859 PEF MEA11022 This course covers activities associated with preventive maintenance of pipeline compressor units. A well-structured compressor maintenance program provides improved safety, reliability, efficiency, run-time, housekeeping and environmental/regulatory compliance. The degree of compressor dependability is in direct proportion to the effectiveness of the preventive maintenance program. Therefore, it is very important to maintain compressors to ensure pipeline capacity and efficiency. It is also important as an operator to know how to recognize and properly react to an AOC should one occur during maintenance. March 2017 Page 27 of 75

Compressor station equipment and its operation. Compressor preventive maintenance program requirements. Actions for keeping compressor units operating safely and efficiently. Procedures for routine maintenance of compressor stations. Recognizing and reacting to compressor station abnormal operating conditions. ASME 0471 Reciprocating Compressor Inspection, Testing and Corrective Maintenance TNG MEA11186 KNT MEA1860 PEF MEA11023 Whether it's new, replaced or rebuilt, a reciprocating compressor needs to function within specified parameters. Typically, inspections and tests are used to confirm that both the compressor's components and its performance meet the required operating conditions. If conditions are not met, then corrective measures are needed. Reciprocating compressor inspection, testing and corrective maintenance specifications and procedures. Checking test equipment. Performing a visual inspection. Diagnosing/troubleshooting abnormal conditions. Performing corrective maintenance. Testing operating parameters. Documenting requirements. Recognizing and reacting to abnormal operating and anticipated conditions. ASME 0481 Centrifugal Compressor Inspection, Testing and Corrective Maintenance TNG MEA11187 KNT MEA1861 PEF MEA11024 Whether it is new, replaced, or rebuilt, a centrifugal compressor needs to function within specified parameters. Typically, inspections and tests are used to confirm that both the compressor's components and its performance meet the required operating conditions. If conditions are not met, then corrective measures are needed. March 2017 Page 28 of 75

Centrifugal compressor inspection, testing & corrective maintenance specifications and procedures. Checking test equipment. Performing a visual inspection. Diagnosing and troubleshooting abnormal conditions. Performing corrective maintenance. Testing operating parameters. Documenting requirements. Recognizing and reacting to abnormal operating and anticipated conditions. ASME 0491 Rotary Compressor Inspection, Testing and Corrective Maintenance TNG MEA11188 KNT MEA1862 PEF MEA11025 Whether it's new, replaced, or rebuilt, a rotary compressor needs to function within specified parameters. Typically, inspections and tests are used to confirm that both the compressor's components and its performance meet the required operating conditions. If conditions are not met, then corrective measures are needed. Rotary compressor inspection, testing & corrective maintenance specification and procedures Checking test equipment. Performing a visual inspection. Diagnosing/troubleshooting abnormal conditions. Performing corrective maintenance. Testing operating parameters. Documenting requirements. Recognizing and reacting to abnormal operating and anticipated conditions. ASME 0501 Pump Preventive Maintenance TNG MEA11189 KNT MEA1863 PEF MEA11026 A well-structured pump maintenance program provides improved safety, reliability, efficiency, run-time, housekeeping and environmental regulatory compliance. The degree of pump dependability is in direct proportion March 2017 Page 29 of 75

to the effectiveness of the preventive maintenance program. Therefore, it is very important to maintain pumps to ensure pipeline capacity, efficiency and safety. It is also important as an operator to know how to recognize and properly react to an AOC should one occur. Pump station equipment. Pump station maintenance programs. Pump station inspection, monitoring & maintenance requirements. Preventive maintenance procedures. Recognizing and reacting to abnormal operating conditions during maintenance activities. ASME 0511 Centrifugal Pump Inspection and Testing and Corrective Maintenance TNG MEA11190 KNT MEA1864 PEF MEA11027 Whether it is new, replaced, or rebuilt, a centrifugal pump needs to function within specified parameters. Typically, inspections and tests are used to confirm that both the pump's components and its performance meet the required operating conditions. If conditions are not met, then corrective measures are needed. Centrifugal pump inspection, testing and corrective maintenance specifications and procedures. Checking test equipment. Performing a visual inspection. Diagnosing/troubleshooting abnormal conditions. Performing corrective maintenance. Testing operating parameters. Documenting requirements. Preventive maintenance procedures. Recognizing and reacting to abnormal operating and anticipated conditions. ASME 0521 Reciprocating Pump Inspection and Testing and Corrective Maintenance TNG MEA11191 KNT MEA1865 PEF MEA11028 March 2017 Page 30 of 75

Whether it's new, replaced or rebuilt, a reciprocating pump needs to function within specified parameters. Typically, inspections and tests are used to confirm that both the pump's components and its performance meet the required operating conditions. If conditions are not met, then corrective measures are needed. Reciprocating pump inspection, testing and corrective maintenance specifications and procedures. Checking test equipment. Performing a visual inspection. Diagnosing/troubleshooting abnormal conditions. Performing corrective maintenance. Testing operating parameters. Documenting requirements. Recognizing and reacting to abnormal operating and anticipated conditions. ASME 0531 Rotary Pump Inspection and Testing and Corrective Maintenance TNG MEA11192 KNT MEA1866 PEF MEA11029 Whether it's new, replaced or rebuilt, a rotary pump needs to function within specified parameters. Typically, inspections and tests are used to confirm that both the pump's components and its performance meet the required operating conditions. If conditions are not met, then corrective measures are needed. Rotary pump inspection, testing and corrective maintenance specifications and procedures. Checking test equipment. Performing a visual inspection. Diagnosing/troubleshooting abnormal conditions. Performing corrective maintenance. Testing operating parameters. Documenting requirements. Recognizing and reacting to abnormal operating and anticipated conditions. ASME 0541 Screw Pump Inspection and Testing and Corrective Maintenance TNG MEA11193 KNT MEA1867 PEF MEA11030 March 2017 Page 31 of 75

Whether it's new, replaced or rebuilt, a screw pump needs to function within specified parameters. Typically, inspections and tests are used to confirm that both the pump's components and its performance meet the required operating conditions. If conditions are not met, then corrective measures are needed. Screw pump inspection, testing and corrective maintenance specifications and procedures. Checking test equipment. Performing a visual inspection. Diagnosing/troubleshooting abnormal conditions. Performing corrective maintenance. Testing operating parameters. Documenting requirements. Recognizing and reacting to abnormal operating and anticipated conditions. ASME-0551 Explosive Atmospheric Detection and Alarm System Performance Test and Corrective Maintenance TNG MEA11194 KNT MEA1868 PEF MEA11031 A natural gas distribution and/or transportation pipeline system should have a gas detection and alarm system to monitor the risk of combustible gas. This course covers permanently installed systems used to detect gas in the atmosphere and their alarm systems. Identify gas detection systems and their functions. Maintain gas detection systems through performance tests. Recognize and react to abnormal operating conditions. ASME 0561 Pressure Test Non-Liquid Medium Test Pressure Less Than 100 psi TNG MEA11195 KNT MEA1869 PEF MEA11032 March 2017 Page 32 of 75

This course discusses pressure testing using a non-liquid medium with MAOP less than 100 psi. Understanding MAOP, system types, service lines and mains for pressurized pipelines. Identifying factors to consider when determining pressure testing requirements. Understanding required preparation for the pressure test. Describing steps required to perform the pressure test. ASME 0571 Pressure Test Non-Liquid Medium Test Pressure Greater Than or Equal to 100 psi TNG MEA11196 KNT MEA1870 PEF MEA11033 This course discusses pressure testing using a non-liquid medium with MAOP greater than or equal to 100 psi. Understanding MAOP, system types, service lines and mains for pressurized pipelines. Identifying factors to consider when determining pressure testing requirements. Understanding required preparation for the pressure test. Describing steps required to perform the pressure test. ASME 0581 Pressure Test Liquid Medium TNG MEA11197 KNT MEA1871 PEF MEA11034 This course discusses pressure testing using a liquid medium. Understanding MAOP, system types, service lines and mains for pressurized pipelines. Identifying factors to consider when determining pressure testing requirements. Understanding required preparation for the pressure test. March 2017 Page 33 of 75

Describing steps required to perform the pressure test. ASME 0591 Leak Test at Operating Pressure TNG MEA11198 KNT MEA1872 PEF MEA11035 This course covers activities associated with the detection of pipeline leaks at standard operating pressure either visually or with the use of leak detection equipment. Identifying leak test requirements. Preparing equipment for leak testing. Performing leak tests at operating pressure. ASME 0601 NDT Radiographic Testing TNG MEA11199 KNT MEA1873 PEF MEA11036 Welding is the most common way to join metals in many trades, and pipelines are no exception. Whether joining pipe sections, repairing pipe, or installing a pipeline component, welding provides a strong joining solution. But what happens when welds are defective? Pipes may burst, product may escape, and dangerous explosions may result. The field of nondestructive testing (NDT) provides a way to test completed welds and detect non-visible defects for the purpose of preventing these situations. This course covers radiographic testing, a form of NDT. Various nondestructive testing methods. Qualification of personnel performing NDT. Safety issues and precautions. Performing radiographic testing. Interpreting radiographic test results and identifying weld defects. Documentation requirements. March 2017 Page 34 of 75

ASME 0611 NDT Liquid Penetrant Testing TNG MEA11200 KNT MEA1874 PEF MEA11037 Welding is the most common way to join metals in many trades, and pipelines are no exception. Whether joining pipe sections, repairing pipe, or installing a pipeline component, welding provides a strong joining solution. But what happens when welds are defective? Pipes may burst, product may escape, and dangerous explosions may result. The field of nondestructive testing (NDT) provides a way to test completed welds and detect non-visible defects for the purpose of preventing these situations. This course covers liquid penetrant testing, a form of NDT. Various nondestructive testing methods. Qualification of personnel performing NDT. Safety issues and precautions. Performing liquid penetrant testing. Evaluating test results and identifying weld defects. Documentation requirements. ASME 0621 NDT Magnetic Particle Testing TNG MEA11201 KNT MEA1875 PEF MEA11038 Welding is the most common way to join metals in many trades, and pipelines are no exception. Whether joining pipe sections, repairing pipe, or installing a pipeline component, welding provides a strong joining solution. But what happens when welds are defective? Pipes may burst, product may escape, and dangerous explosions may result. The field of nondestructive testing (NDT) provides a way to test completed welds and detect non-visible defects for the purpose of preventing these situations. This course covers magnetic particle testing, a form of NDT. Various nondestructive testing methods. Qualification of personnel performing NDT. Safety issues and precautions. Performing magnetic particle testing. Evaluating test results and identifying weld defects. March 2017 Page 35 of 75

Documentation requirements. ASME 0631 NDT Ultrasonic Testing TNG MEA11202 KNT MEA1876 PEF MEA11039 Welding is the most common way to join metals in many trades, and pipelines are no exception. Whether joining pipe sections, repairing pipe, or installing a pipeline component, welding provides a strong joining solution. But what happens when welds are defective? Pipes may burst, product may escape, and dangerous explosions may result. The field of nondestructive testing (NDT) provides a way to test completed welds and detect non-visible defects for the purpose of preventing these situations. This course covers ultrasonic testing, a form of NDT. Various nondestructive testing methods. Qualification of personnel performing NDT. Safety issues and precautions. Performing ultrasonic testing. Interpreting ultrasonic test results and identifying weld defects. Documentation requirements. ASME-0641 Visually Inspect Pipe and Components - Prior to Installation TNG MEA11203 KNT MEA1877 PEF MEA11040 This course discusses requirements and procedures for visual inspection of pipeline and components prior to installation. Federal requirements for pre-installation inspection. Procedures for visually inspecting pipeline and components. Repair and replacement requirements as outlined in the Code of Federal regulations. March 2017 Page 36 of 75