Grove YB5520 Product Guide ASME B30.5 Imperial 85%, Metric 85% and DIN/ISO

Grove YB552 Product Guide ASME B3.5 Imperial 85%, Metric 85% and DIN/ISO Features 18 t (2 USt) capacity 16,6 m (54.5 ft) four-section, four-plate full power boom 9,7 t (1 USt) deck carrying capacity Exclusive pivoting boom nose

Features Steering The YB552 comes standard with three steering modes: front (two-wheel), four-wheel coordinated, and four-wheel crab steer with electronic self alignment. Operators can choose between modes using a three-position rocker switch located on dash panel. The reach and capacity to get the job done The 5,64 m - 16,61 m (18.5 ft - 54.5 ft) four-section boom can be enhanced with optional boom extensions. The 4,6 m (15 ft) fixed swingaway extension offers a maximum tip height of 23,1 m (76 ft) while the 4,6 m - 7,6 m (15 ft - ft) telescopic extension provides a maximum tip height of 26,2 m (86 ft). Both extensions can be offset, -15, and -3 via the pivoting boom nose. Outriggers The YB552 outriggers are two position ( and 1 ) beam/jack style with inverted jack cylinders and pivoting pad. Pivoting boom nose Three-position mechanically offset (, 4, and 8 ), lowers boom nose head height by 4,5 cm (1.33 ft) when pivoted fully forward. Negative pivoting of,, and 3 allows boom extension offset capability. Operator cab New operator control layout with hydraulic proportional joystick controls, tilt steering wheel, and automotive dash panel gauges and indicator lights.

Contents Specifications 4 Dimensions 7 Dimensions and weights 8 Range diagram 9 Load chart 1 Metric 85% range diagram 12 Metric 85% load chart 13 DIN/ISO range diagram 15 DIN/ISO load chart 16 Rigging chart 18 Symbols glossary 19

Specifications Superstructure 5,64 m 16,61 m (18.5 ft 54.5 ft) four-section full power boom. Maximum tip height: 19,2 m ( ft) *Optional boom extensions 4,6 m (15 ft) fixed swingaway extension. Maximum tip height: 23,1 m (76 ft) 4,6 m 7,6 m (15 ft ft) telescopic swingaway extension. Maximum tip height: 26,2 m (86 ft) Both extensions can be offset, -15, and -3 via pivoting boom nose. nose Two sheave, quick reeve type with three- pinned pivoting (, +4, and +8 ) design to minimize head space requirements. Lowers head height 4,5 cm (1.33 ft) when nose is pivoted fully forward. elevation Two double acting hydraulic cylinders with integral holding valve. Elevation: to 8. Anti-two block device Standard anti-two block device (hard wired), which, when activated, provides an audible and visual warning to the operator and locks out all functions whose movement can cause two-blocking. Rated Capacity Indicator (RCI) Black and white, graphical display of boom angle, boom length, boom radius, rated load, and calculated load. Allows for operator inputs to set the crane configuration. RCI system is hardwired and calculates load via pressure transducers in the lift cylinder. Display includes a color coded light bar and audible alarm with function cut-out if load exceeds the load chart parameters. Swing Ball bearing swing circle with 36 continuous rotation. Worm gear and pinion driven by hydraulic motor. Spring applied, hydraulic released brake. Equipped with swing enable control. Maximum speed: 2.5 rpm Hydraulic system One pressure compensated variable displacement axial piston pump, with load sensing. Maximum output of: 155 LPM (41. GPM) Maximum operating pressure: 276 bars (4 p.s.i.) Six-section valve bank, chassis mounted, operated via dash mounted pilot pressure hydraulic joystick controllers. 151,4 L (4 gal) steel hydraulic reservoir with sight level gauge and steel side plating to guard against side impact. Return line replaceable filter with by-pass protection and service indicator. Cartridge filter rating of three micron. Hoist specifications Two speed gear motor driven hoist with automatic spring applied / hydraulically released wet brake. Smooth drum with cable follower and third wrap indication with function cut out. An electronic drum rotation indicator in hoist joystick control and hoist directional indicator light on the cab dashboard are also included Maximum hoist pull (first layer):,6 kn (14,3 lb) Maximum permissible single line pull:,5 kn (1, lb.) (3.5:1 design factor) Maximum single line speed: 64 m/min (21 fpm) Rope construction: 6 x 19 XXIPS / IWRC Rope diameter: 14 mm (9/16 in) Rope length: 97,5 m (32 ft) *Optional RCI system includes a full color graphical display, work area definition (WADS), and a datalogger. 4 *Denotes optional equipment

Specifications Carrier Fuel tank capacity Chassis High strength alloy frame constructed with integral outrigger housings; front and rear lifting, tie-down, and towing lugs. 6.2 m2 (66.3 ft2) carrydeck size with 972 kg (2, lb) deck only carrying capacity. Deck coated with anti-skid treatment. Steel with side impact plate. Capacity: 151,4L (4 gal). Transmission Powershift with four speeds forward and four reverse. Steering column mounted shifter. Outriggers Single stage hydraulic telescoping beam with oblique style jack cylinder on all four corners. Provides extended and down and retracted and down lifting capabilities. Integral holding valve on both beam and jack. Outrigger positioning indicator located in dash display. Outrigger pad size: 222 mm x 4 mm (8.75 in x 1 in) Maximum outrigger pad load: 15 876 kg (35, lb). Outrigger controls Independent outrigger control rocker switches for beam or jack selection with a separate extend /retract rocker selector switch. 36 level bubble located inside cab. Engine (Tier IV) Cummins QSB 3,3 L four cylinder / turbo-charged diesel rated at 75 kw (1 hp) at 26 rpm. Includes standard 12V engine block heater and air intake Grid heater. Engine hourmeter located in dash display. Alternator: 12 amp. Maximum Torque: 414 Nm (35 ft/lb). Fuel requirements: Maximum of 15 ppm sulphur content Requires Ultra Low diesel fuel. NOTE: Tier IV required for sale in North America and European Union countries. Engine (Tier III) Cummins QSB 3.3L four cylinder / turbo-charged diesel rated at 74 kw (99 hp) at 26 r.p.m. Includes std. 12V engine block heater and air intake Grid heater. Engine hourmeter located in dash display. Alternator: 9 amp. Maximum Torque: 415 Nm (36 ft/lb). NOTE: Required for sale outside of North America and European Union countries. Operators control station Frame mounted, open air style control station with cab shell includes all crane functions and driving controls and equipped with overhead safety glass. Other standard equipment includes a suspension seat with seat belt, sight level bubble and 1,1 kg (2.5 lb) fire extinguisher, and tilt steering wheel. The dash panel will display the fuel level gauge, water temperature gauge, engine r.p.m., battery voltage, and hour meter. Indicator lights will display parking brake, low transmission pressure, low brake pressure, outrigger position, headlights, work lights (if ordered), and hoist 3rd wrap (if ordered). Crane function indicator and turn signal indicators are also included. The load indicator display will be mounted on the top of the dash panel for direct line of sight for the operator. *Operators control station enclosed Includes the standard cab shell and all controls and indicators noted above, with the addition of front, rear, and right side glass, a split (two-piece) hinged door with sliding glass, front windshield wiper and washer, hot water heater and defroster with fan and cab dome light. Electrical system One heavy duty maintenance free 12V battery, 82CCA at F. Drive Two-wheel (front-wheel) as standard with four-wheel drive as an option. Drive axles supplied with planetary hubs and limited slip differential. *Denotes optional equipment Grove YB552 5

Specifications Carrier continued Steer Standard three steering modes. Front (two-wheel), four-wheel coordinated, and four-wheel crab steer with electronic self alignment. Three position rocker switch located on dash panel. Outside Turning Radius: Two wheel steer: 6,2 m (2 ft 4.8 in) Four wheel steer: 3,9 m (13 ft 1 in) Suspension/axles Front: Drive / steer in both two-wheel drive and four-wheel drive Rear: non-drive with steer in two-wheel drive, drive/ steer in four-wheel drive. Front axle is rigid mounted to frame. Rear axle offers 1.5 of oscillation. Brakes Hydraulic actuated internal wet-disc service brake acting on each drive wheel. Dash mounted rocker switch with indicator light for activating or release of the dry disc parking brake mounted on the transmission output yoke. Tires Tubeless type, semi-aggressive tread. 12. R2 Lights Full LED lighting includes turn indicators, head, tail, brake, and hazard warning lights recessed mounted. Maximum speed 33,8 km/h (21. mph) Gradeability (theoretical) 68%...(to drive train stall) NO LOAD 4%...(to drive train stall) with 972 kg (2, lb) DECK LOAD Gross vehicle weight (G.V.W.) 16 494 kg (36,364 lb) basic unit with Tier IV engine. Miscellaneous standard equipment 18 t (2 USt) two-sheave low profile galvanize coated hook block with quick reeve design, back-up motion alarm, outrigger motion alarm, no-skid decking, front and rear lifting, towing, and tie-down lugs. *Optional equipment Auxiliary Lighting: Includes cab mounted amber flashing light and dual base boom mounted LED work lights. Convenience Package: Includes front and rear pintle hitch, dual rear view mirrors, head and tail light metal mesh grille covers. Enclosed Cab Package: Includes heater and defroster, cab dome light, all window glass, and two-piece split door. Four-wheel drive Below deck hydraulic tow winch with 4536 kg (1, lb) capacity. 4,6 m (15 ft) fixed boom extension 4,6 m 7,6 m (15 ft ft) telescopic boom extension Air conditioning (closed cab option required) 36 swing lock C.E. compliant package 6 *Denotes optional equipment

Dimensions Dimensions Two-wheel steer A B C D E 35 mm (11 ft 1 in) 658 mm (19 ft 1.5 in) 6218 mm (2 ft 4.8 in) 6675 mm (21 ft 1.8 in) 747 mm (24 ft 3.6 in) 114 mm (.9") 8 1431 mm (56.3") 4 Four-wheel steer 1722 mm (5 ft 8 in) 3841 mm (12 ft 7 in) 3993 mm (13 ft 1 in) 81 mm (14 ft 8 in) 538 mm (17 ft 8 in) 2472 mm (97.3") 1283 mm (5.5") Radius B Radius E Radius D Radius C Radius A R 2148 mm (84.6") 179 mm (7.") 7121 mm (28.3") Retracted 5648 mm (222.3") Retracted 16 612 mm (654.") Extended 2465 mm (97.") 1546 mm (6.9") 242 mm (9.5") 919 mm (36.2") 755 mm (29.7") 24 175 mm (42.3") 24 69 mm (11.1") Dimensions are shown in mm (in). 1195 mm (47.") 242 mm (95.3") 1994 mm (78.5") 42 mm (158.3") 2283 mm (89.9") 4597 mm (181") 2313 mm (91.1") 4658 mm (183.4") Grove YB552 7

Dimensions and weights 2729 mm (17.4") 2729 mm (17.4") 748 mm (29.4") 2729 mm (17.4") 1873 mm (73.7") 975 mm (38.4") 1951 mm (76.8") 116 mm (45.7") 232 mm (91.3") 2472 mm (97.3") 1964 mm (77.3") 1262 mm (49.7") 92 mm (3.6") 2439 mm (95.9") 2671 mm (15.2") 122 mm (48.") 1336 mm (52.6") 439 mm (159.") 4271 mm (168.1") 2136 mm (84.1") 22 mm (79.5") Weights Basic machine: Including 16,6 m (54.5 ft) main boom, main hoist with 97,5 m (32 ft) of wire rope, 18 t (2 USt) hook block, full counterweight, Tier IV engine Add: 4,6 m (15 ft) fixed swingaway extension and extension carrier brackets and downhaul weight GVW Front Rear kg lb kg lb kg lb 16 494 36,364 6175 13,614 1 319 22,75 246 543 8 833-132 -29 Crane weight 16 74 36,97 6553 14,7 1 187 22,46 Basic machine: Including 16,6 m (54.5 ft) main boom, main hoist with 97,5 m (32 ft) of wire rope, 18 t (2 USt) hook block, full counterweight, Tier IV engine 16 494 36,364 6175 13,614 1 319 22,75 Add: Enclosed cab, heater and glass 85 187 82 48 15 Crane weight 16 579 36,551 6212 13,696 1 367 22,855 Basic machine: Including 16,6 m (54.5 ft) main boom, main hoist with 97,5 m (32 ft) of wire rope, 18 t (2 USt) hook block, full counterweight, Tier IV engine Add: 4,6 m - 7,6 m (15 ft - ft) telescopic swingaway extension and extension carrier brackets and downhaul weight 16 494 36,364 6175 13,614 1 319 22,75 392 8 577 1,271-185 -48 Crane weight 16 886,227 6752 14,885 1 134 22,342 8

Working range imperial 85% 88 86 84 82 8 78 76 74 72 7 68 66 64 62 6 58 56 54 52 5 48 46 42 4 38 36 34 32 3 28 26 24 22 2 18 16 14 12 1 8 6 4 2 8 6 4 2 2 4 6 8 1 12 14 16 18 2 22 24 26 28 3 32 34 36 38 4 42 46 48 5 52 54 56 58 6 62 64 66 68 7 72 74 76 79.5' with ' jib 69.5' with 15' jib 3.5' 42.5' 54.5' 18.5' 8 75 7 65 6 55 5 45 4 35 3 8 6 4 2 2 4 6 8 1 12 14 16 18 2 22 24 26 28 3 32 34 36 38 4 42 46 48 5 52 54 56 58 6 62 64 66 68 7 72 74 76 78 2 1 5 88 86 84 82 8 78 76 74 72 7 68 66 64 62 6 58 56 54 52 5 48 46 42 4 38 36 34 32 3 28 26 24 22 2 18 16 14 12 1 8 6 4 2 Height from the ground in feet Operating radius in feet from axis of rotation THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. Grove YB552 9

Load chart imperial 85% Radius (ft) 6 8 1 12 14 15 16 18 2 22 24 26 27 28 3 32 34 36 38 39 4 42 46 48 51 Radius (ft) 6 8 1 12 14 15 16 18 2 22 24 26 27 28 3 32 34 36 38 39 4 42 46 48 51 MAIN BOOM LOAD RATINGS ON OUTRIGGERS Extended and Down 36 or Retracted and Down Front/Rear 1 8.5 ft BOOM 3.5 ft BOOM 42.5 ft BOOM 54.5 ft BOOM Rated Rated Rated Rated Angle Load Angle Load Angle Load Angle Load (deg) (lb) (deg) (lb) (deg) (lb) (deg) (lb) 65 57.5 49.5 39.5.5 MAIN BOOM LOAD RATINGS ON OUTRIGGERS Retracted and Down 36 1 8.5 ft BOOM 3.5 ft BOOM 42.5 ft BOOM 54.5 ft BOOM Rated Rated Rated Rated Angle Load Angle Load Angle Load Angle Load (deg) (lb) (deg) (lb) (deg) (lb) (deg) (lb) 65 57.5 49.5 39.5.5 4 3385 31 2695 2355 18 9 4 3385 248 17 9 1 5 122 7 5.5 7 1.5 67.5 58.5 56.5 54 49 43.5 29.5 19 7 5.5 7 1.5 67.5 58.5 56.5 54 49 43.5 29.5 19 24 24 24 24 24 2 21 1845 1 141 5 12 17 15 24 24 2295 17 95 145 13 11 7 5 97 8 8 7 4 67 527 493 7 7.5 75 72 69 67.5 66 6 56.5 53 49.5 47.5 45.5 41.5 31.5 1 6 7 7.5 7 5 7 2 69 67.5 66 6 56.5 53 49.5 47.5 45.5 41.5 31.5 16 2365 21 55 1985 185 17 1655 15 14 133 122 17 5 11 5 96 862 7 7 9 79 647 592 568 2365 21 1 167 5 1 5 126 11 5 959 81 5 7 3 61 2 538 55 47 5 423 8 338 34 27 4 26 7 9 7 7 74.5 73.5 72.5 7 68 65.5 6.5 59.5 58 55.5 53 5 47 42.5 4.5 33 28.5 23 7 9 7 7 7 4.5 7 3.5 7 2.5 7 68 65.5 6.5 59.5 58 55.5 53 5 47 42.5 4.5 33 28.5 23 168 1535 141 135 13 121 11 155 994 938 91 2 888 843 82 73 668 61 3 589 565 523 485 45 4 1 8 6 168 1535 13 11 95 11 5 956 836 7 36 643 568 535 55 452 45 365 33 298 284 27 1 246 224 23 184 158 1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied. 2) The rated loads shown on outriggers do not exceed 85% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator. 3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See above. 4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting. 5) Ratings on rubber depend on 12.R2 tire capacity, condition of tires and proper inflation pressure (13 psi). Loads on rubber may be transported at a maximum seed of 2.5 mph on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. For 36 ratings on rubber, rear axle oscillation locks must be in place. Do not use jib with crane on rubber. 6) For operating radius not shown, use load rating of next larger radius. 7) The maximum deck load only is 2, lb. Combined boom and deck loads are not permitted on rubber. 8) Do not induce any external side loads to boom or jib. NOTES: SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING. OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY. 3 3 FRONT REAR 1 THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.

Load chart imperial 85% Angle (deg) 8 7 5 7 65 6 55 5 45 4 35 3 2 1 5 1 5 Angle (deg) 1 5 FT JIB CAPACITIES ON EXTENDED OUTRIGGERS Jib Offset Angle To 42.5 ft 93 855 7 95 7 4 695 65 535 455 45 345 33 31 5 3 28 deg 15 deg 3 deg To 54.5 ft 65 61 61 565 435 38 35 28 235 21 5 19 17 5 167 155 To 42.5 ft 7 4 695 65 535 455 45 345 3 31 5 3 28 To 54.5 ft 565 435 38 35 28 235 2 1 5 19 17 5 167 155 Any Length 35 28 235 2 1 5 19 17 5 167 155 1 5 FT - FT JIB CAPACITIES ON EXTENDED OUTRIGGERS 1 5 FT Length FT Length J ib Offset Angle J ib Offset Angle deg 15 deg 3 deg deg 15 deg 3 deg To 42.5 ft To 54.5 ft To 42.5 ft To 54.5 ft Any Length To 42.5 ft To 54.5 ft To 42.5 ft To 54.5 ft Any Length MAIN BOOM ON RUBBER Any Length Radius (ft) Front Rating (lb) 36 Rating (lb) 6 8 1 12 14 15 16 18 2 22 24 26 27 28 3 32 34 36 38 39 4 42 46 48 51 16 141 11 986 87 81 9 7 7 2 689 61 8 557 499 6 422 41 368 33 295 264 235 222 21 6 21 1 191 17 2 155 131 155 1355 18 888 7 42 68 5 589 57 4 6 3 31 281 269 8 2 1 3 189 165 154 142 13 11 7 13 9 7 3 8 75 7 65 6 55 5 45 4 35 3 2 15 1 5 85 699 594 51 9 327 281 242 29 183 1 149 1 1 1 1 855 665 558 47 7 41 354 36 264 229 199 17 5 156 143 1 1 128 128 51 9 327 281 242 29 183 1 149 1 1 1 1 47 7 41 354 36 264 229 199 17 5 156 143 1 1 128 1 36 264 229 199 17 5 156 143 1 1 128 1 583 51 2 433 1 31 9 27 4 235 22 17 3 148 129 11 4 14 1 1 9 8 58 486 47 346 297 6 22 189 1 141 123 19 99 95 95 9 8 1 31 9 27 4 235 22 17 3 148 129 11 4 14 1 1 9 8 346 297 6 22 189 1 141 123 19 99 95 95 9 8 22 189 1 141 123 19 99 95 95 9 8 NOTES: JIB CAPACITY IS LIMITED BY BOTH STRUCTURAL CAPACITY CHART AND MAIN CAPACITY CHART. SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING. OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY. 3 3 FRONT REAR 1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied. 2) The rated loads shown on outriggers do not exceed 85% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator. 3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See above. 4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting. 5) Ratings on rubber depend on 12.R2 tire capacity, condition of tires and proper inflation pressure (13 psi). Loads on rubber may be transported at a maximum seed of 2.5 mph on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. For 36 ratings on rubber, rear axle oscillation locks must be in place. Do not use jib with crane on rubber. 6) For operating radius not shown, use load rating of next larger radius. 7) The maximum deck load only is 2, lb. Combined boom and deck loads are not permitted on rubber. 8) Do not induce any external side loads to boom or jib. THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. Grove YB552 The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 11

Working range metric 85% 1,8,6,6 1,8 3, 4,3 5,5 6,7 7,9 9,1 1,4 11,6 12,8 14, 15,2 16,5 17,7 18,9 2,1 21,3 22,6 23,2 24,4 1,2 1,2 2,4 3,7 4,9 6,1 7,3 8,5 9,8 11, 12,2 13,4 14,6 15,8 17,1 18,3 19,5 2,7 21,9 23,2 23,8 26,8 26,8 26,2 26,2,6,6,, 24,4 24,4 23,8 23,8 23,2 23,2 22,6 22,6 21,9 21,9 21,3 21,3 2,7 2,7 2,1 2,1 19,5 19,5 18,9 18,9 18,3 18,3 17,7 17,7 17,1 17,1 16,5 16,5 15,8 8 15,8 75 15,2 7 15,2 14,6 65 14,6 6 14, 14, 13,4 55 13,4 12,8 5 12,8 12,2 45 12,2 11,6 11,6 11, 1,4 9,8 4 35 11, 1,4 9,8 9,1 8,5 3 9,1 8,5 7,9 7,9 7,3 7,3 2 6,7 6,7 6,1 6,1 5,5 5,5 4,9 4,3 1 4,9 4,3 3,7 3, 5 3,7 3, 2,4 2,4 1,8 1,8 1,2 1,2,6,6 1,2 1,2 2,4 3,7 4,9 6,1 7,3 8,5 9,8 11, 12,2 13,4 14,6 15,8 17,1 18,3 19,5 2,7 21,9 23,2 23,8 1,8,6,6 1,8 3, 4,3 5,5 6,7 7,9 9,1 1,4 11,6 12,8 14, 15,2 16,5 17,7 18,9 2,1 21,3 22,6 23,2 24,4 24,2 m BOOM WITH 7,6 m JIB 21,2 m BOOM WITH 4,6 m JIB 5,6 m BOOM 9,3 m BOOM 13, m BOOM 16,6 m BOOM Height from the ground in meters Operating radius in meters from axis of rotation 12 THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.

Load chart metric 85% Radius (m) 2, 2,4 3, 3,7 4,3 4,6 4,9 5,5 6,1 6,7 7,3 7,9 8,2 8,5 9,1 9,8 1,4 11, 11,6 11,9 12,2 12,8 13,4 14, 14,6 15,5 Radius (m) 2, 2,4 3, 3,7 4,3 4,6 4,9 5,5 6,1 6,7 7,3 7,9 8,2 8,5 9,1 9,8 1,4 11, 11,6 11,9 12,2 12,8 13,4 14, 14,6 15,5 MAIN BOOM LOAD RATINGS ON OUTRIGGERS Extended and Down 36 or Retracted and Down Front/Rear 5,6 m BOOM 9,3 m BOOM 13, m BOOM 16,6 m BOOM Rated Rated Rated Rated Angle Load Angle Load Angle Load Angle Load (deg) (kg) (deg) (kg) (deg) (kg) (deg) (kg) 58 5 38,5 24,5 MAIN BOOM LOAD RATINGS ON OUTRIGGERS Retracted and Down 36 5,6 m BOOM 9,3 m BOOM 13, m BOOM 16,6 m BOOM Rated Rated Rated Rated Angle Load Angle Load Angle Load Angle Load (deg) (kg) (deg) (kg) (deg) (kg) (deg) (kg) 58 5 38,5 24,5 18 15 35 13 65 12 2 1 5 857 18 15 35 11 55 7955 615 555 74,5 71,5 67,5 62,5 58,5 56 53,5 49 43,5 29,5 19,5 74,5 71,5 67,5 62,5 58,5 56 53,5 49 43,5 29,5 19,5 1 875 1 875 1 875 1 875 1 875 1 2 95 8365 739 6 556 495 461 1 875 1 875 1 55 7955 6455 585 55 438 15 3195 278 24 227 78 75 71,5 69 67,5 66 6 56,5 53 49,5 47,5 46 41,5 36,5 31 15,5 78 75 71,5 69 67,5 66 6 56,5 53 49,5 47,5 46 41,5 36,5 31 15,5 1 7 9775 9 8185 782 755 6915 646 5555 495 4 438 394 351 32 293 269 9 1 7 9695 743 6145 55 517 433 3695 32 2795 246 2315 2185 195 1715 154 139 15 12 79 76,5 74,5 73,5 72,5 7 68 65,5 61 59,5 58,5 56 52,5 5 47 42,5 4,5 33 28,5 23 79 76,5 74,5 73,5 72,5 7 68 65,5 61 59,5 58,5 56 52,5 5 47 42,5 4,5 33 28,5 23 762 696 95 612 5895 5485 51 4785 455 45 4135 4 382 36 33 32 278 267 65 2 22 245 195 1715 762 696 581 535 495 4285 55 331 29 65 242 2285 245 185 16 147 1335 127 121 11 15 915 83 7 1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied. 2) The rated loads shown on outriggers do not exceed 85% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator. 3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See reduction chart. 4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting. 5) Ratings on rubber depend on 12.R2 tire capacity, condition of tires and proper inflation pressure (8,96 bar). Loads on rubber may be transported at a maximum seed of 4, km/h on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. For 36 ratings on rubber, rear axle oscillation locks must be in place. Do not use jib with crane on rubber. 6) For operating radius not shown, use load rating of next larger radius. 7) The maximum deck load only is 972 kg. Combined boom and deck loads are not permitted on rubber. 8) Do not induce any external side loads to boom or jib. NOTES: SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING. OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY. 3 3 FRONT REAR THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. Grove YB552 The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 13

Load chart metric 85% Angle (deg) 8 75 7 65 6 55 5 45 4 35 3 2 15 1 5 Angle (deg) 8 75 7 65 6 55 5 45 4 35 3 2 15 1 5 4,6 m FIXED J IB CAPACITIES ON EXTENDED OUTRIGGGERS (kg) Jib Offset Angle deg 15 deg 3 deg To 13, m To 13, m Any Length 4215 2945 3355 6 1585 3875 2765 315 197 127 365 2765 2945 172 165 3355 6 24 1585 975 315 197 26 127 86 2945 172 1835 165 79 24 1585 1565 975 76 26 127 1495 86 7 1835 1565 1495 14 136 127 165 975 86 79 76 7 14 136 127 79 76 7 4,6 m - 7,6 m TELE JIB CAPACITIES ON EXTENDED OUTRIGGGERS (kg) 4,6 m Length 7,6 m Length Jib Offset Angle Jib Offset Angle deg 15 deg 3 deg deg 15 deg 3 deg To 13, m 3855 317 269 231 1995 1715 148 1275 195 945 83 735 675 65 65 65 565 3875 315 3 216 186 165 1385 1195 135 9 79 75 645 62 62 58 565 To 13, m 231 1995 1715 148 1275 195 945 83 735 675 65 65 65 565 216 186 165 1385 1195 135 9 79 75 645 62 62 58 565 Any 1385 1195 135 9 79 75 645 62 62 58 565 To 13, m 264 232 196 168 15 124 165 915 785 67 585 515 47 45 45 45 36 2 22 1845 1565 1345 116 995 855 735 64 555 49 5 43 43 45 36 To 13, m 168 15 124 165 915 785 67 585 515 47 45 45 45 36 1565 1345 116 995 855 735 64 555 49 5 43 43 45 36 Any 995 855 735 64 555 49 5 43 43 45 36 MAIN BOOM ON RUBBER Any Length Radius (m) Front Rating (kg) 2, 6965 2,4 95 3, 51 3,7 7 4,3 3945 4,6 1 5 4,9 35 5,5 3 1 6,1 28 6,7 7,3 226 7,9 22 8,2 191 8,5 186 9,1 1665 9,8 1495 1,4 1335 11, 1195 11,6 165 11,9 15 12,2 98 12,8 955 13,4 865 14, 78 14,6 7 15,5 59 36 Rating (kg) 6735 6145 4895 4 3365 38 288 267 23 198 17 5 147 1365 127 5 122 11 7 965 855 7 45 695 64 59 53 465 45 33 NOTES: JIB CAPACITY IS LIMITED BY BOTH STRUCTURAL CAPACITY CHART AND MAIN CAPACITY CHART. SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING. OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY. 3 3 FRONT REAR 1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied. 2) The rated loads shown on outriggers do not exceed 85% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator. 3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See reduction chart. 4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting. 5) Ratings on rubber depend on 12.R2 tire capacity, condition of tires and proper inflation pressure (8,96 bar). Loads on rubber may be transported at a maximum seed of 4, km/h on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. For 36 ratings on rubber, rear axle oscillation locks must be in place. Do not use jib with crane on rubber. 6) For operating radius not shown, use load rating of next larger radius. 7) The maximum deck load only is 972 kg. Combined boom and deck loads are not permitted on rubber. 8) Do not induce any external side loads to boom or jib. 14 THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.

Working range DIN/ISO 1,8,6,6 1,8 3, 4,3 5,5 6,7 7,9 9,1 1,4 11,6 12,8 14, 15,2 16,5 17,7 18,9 2,1 21,3 22,6 23,2 24,4 1,2 1,2 2,4 3,7 4,9 6,1 7,3 8,5 9,8 11, 12,2 13,4 14,6 15,8 17,1 18,3 19,5 2,7 21,9 23,2 23,8 26,8 26,8 26,2 26,2,6,6,, 24,4 24,4 23,8 23,8 23,2 23,2 22,6 22,6 21,9 21,9 21,3 21,3 2,7 2,7 2,1 2,1 19,5 19,5 18,9 18,9 18,3 18,3 17,7 17,7 17,1 17,1 16,5 16,5 15,8 8 15,8 75 15,2 7 15,2 14,6 65 14,6 6 14, 14, 13,4 55 13,4 12,8 5 12,8 12,2 45 12,2 11,6 11,6 11, 1,4 9,8 4 35 11, 1,4 9,8 9,1 8,5 3 9,1 8,5 7,9 7,9 7,3 7,3 2 6,7 6,7 6,1 6,1 5,5 5,5 4,9 4,3 1 4,9 4,3 3,7 3, 5 3,7 3, 2,4 2,4 1,8 1,8 1,2 1,2,6,6 1,2 1,2 2,4 3,7 4,9 6,1 7,3 8,5 9,8 11, 12,2 13,4 14,6 15,8 17,1 18,3 19,5 2,7 21,9 23,2 23,8 1,8,6,6 1,8 3, 4,3 5,5 6,7 7,9 9,1 1,4 11,6 12,8 14, 15,2 16,5 17,7 18,9 2,1 21,3 22,6 23,2 24,4 24,2 m BOOM WITH 7,6 m JIB 21,2 m BOOM WITH 4,6 m JIB 5,6 m BOOM 9,3 m BOOM 13, m BOOM 16,6 m BOOM Height from the ground in meters Operating radius in meters from axis of rotation THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. Grove YB552 15

Load chart DIN/ISO Radius (m) 2, 2,4 3, 3,7 4,3 4,6 4,9 5,5 6,1 6,7 7,3 7,9 8,2 8,5 9,1 9,8 1,4 11, 11,6 11,9 12,2 12,8 13,4 14, 14,6 15,5 Radius (m) 2, 2,4 3, 3,7 4,3 4,6 4,9 5,5 6,1 6,7 7,3 7,9 8,2 8,5 9,1 9,8 1,4 11, 11,6 11,9 12,2 12,8 13,4 14, 14,6 15,5 MAIN BOOM LOAD RATINGS ON OUTRIGGERS Extended and Down 36 or Retracted and Down Front/Rear 5,6 m BOOM 9,3 m BOOM 13, m BOOM 16,6 m BOOM Rated Rated Rated Rated Angle Load Angle Load Angle Load Angle Load (deg) (kg) (deg) (kg) (deg) (kg) (deg) (kg) 58 5 38,5 24,5 MAIN BOOM LOAD RATINGS ON OUTRIGGERS Retracted and Down 36 5,6 m BOOM 9,3 m BOOM 13, m BOOM 16,6 m BOOM Rated Rated Rated Rated Angle Load Angle Load Angle Load Angle Load (deg) (kg) (deg) (kg) (deg) (kg) (deg) (kg) 58 5 38,5 24,5 18 15 35 13 65 12 2 1 5 857 18 14 8 1 7 7955 615 555 74,5 71,5 67,5 62,5 58,5 56 53,5 49 43,5 29,5 19,5 74,5 71,5 67,5 62,5 58,5 56 53,5 49 43,5 29,5 19,5 1 875 1 875 1 875 1 875 1 4 977 8975 789 688 591 5145 45 4 1 875 1 875 9535 732 65 5595 511 438 15 3195 278 24 227 78 75 71,5 69 67,5 66 6 56,5 53 49,5 47,5 46 41,5 36,5 31 15,5 78 75 71,5 69 67,5 66 6 56,5 53 49,5 47,5 46 41,5 36,5 31 15,5 1 7 9775 9 8185 782 755 6915 646 592 5155 4545 4285 5 35 323 293 2675 245 2355 1 7 857 675 561 5215 479 4155 3645 32 2795 246 2315 2185 195 1715 154 139 15 12 79 76,5 74,5 73,5 72,5 7 68 65,5 61 59,5 58,5 56 52,5 5 47 42,5 4,5 33 28,5 23 79 76,5 74,5 73,5 72,5 7 68 65,5 61 59,5 58,5 56 52,5 5 47 42,5 4,5 33 28,5 23 762 696 95 612 5895 5485 51 4785 455 45 4135 4 1 335 35 275 243 233 215 199 1845 171 1535 762 6185 52 487 9 3915 3455 275 248 2355 224 235 185 16 147 1335 127 121 11 15 915 83 7 1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied. 2) The rated loads shown on outriggers do not exceed 8% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator. 3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See reduction chart. 4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting. 5) Ratings on rubber depend on 12.R2 tire capacity, condition of tires and proper inflation pressure (8,96 bar). Loads on rubber may be transported at a maximum seed of 4, km/h on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. For 36 ratings on rubber, rear axle oscillation locks must be in place. Do not use jib with crane on rubber. 6) For operating radius not shown, use load rating of next larger radius. 7) The maximum deck load only is 972 kg. Combined boom and deck loads are not permitted on rubber. 8) Do not induce any external side loads to boom or jib. NOTES: SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING. OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY. 3 3 FRONT REAR 16 THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.

Load chart DIN/ISO Angle (deg) 8 75 7 65 6 55 5 45 4 35 3 2 15 1 5 Angle (deg) 8 75 7 65 6 55 5 45 4 35 3 2 15 1 5 3855 317 269 231 1995 1715 148 1275 195 945 83 735 675 65 65 65 565 4,6mFIXED JIB CAPACITIES ON EXTENDED OUTRIGGGERS (kg) Jib Offset Angle deg 15 deg 3 deg To 13, m To 13, m Any Length 4215 3875 365 3355 315 29 24 26 1835 1565 1465 14 136 2945 2765 2765 6 197 172 1585 127 165 975 86 79 76 3355 315 2945 24 26 1835 1565 1495 14 136 127 6 197 172 1585 127 165 975 86 79 76 7 1585 127 165 975 86 79 76 7 127 7 4,6 m - 7,6 m TELE JIB CAPACITIES ON EXTENDED OUTRIGGGERS (kg) 4,6 m Length 7,6 m Length To 13, m Jib Offset Angle Jib Offset Angle deg 15 deg 3 deg deg 15 deg 3 deg 3875 315 3 216 186 165 1385 1195 135 9 79 75 645 62 62 58 565 To 13, m 231 1995 1715 148 1275 195 945 83 735 675 65 65 65 565 216 186 165 1385 1195 135 9 79 75 645 62 62 58 565 Any 1385 1195 135 9 79 75 645 62 62 58 565 To 13, m 264 232 196 168 15 124 165 915 785 67 585 515 47 45 45 45 36 2 22 1845 1565 1345 116 995 855 735 64 555 49 5 43 43 45 36 To 13, m 168 15 124 165 915 785 67 585 515 47 45 45 45 36 1565 1345 116 995 855 735 64 555 49 5 43 43 45 36 Any 995 855 735 64 555 49 5 43 43 45 36 Radius (m) 2, 2,4 3, 3,7 4,3 4,6 4,9 5,5 6,1 6,7 7,3 7,9 8,2 8,5 9,1 9,8 1,4 11, 11,6 11,9 12,2 12,8 13,4 14, 14,6 15,5 MAIN BOOM ON RUBBER Any Length Front Rating (kg) 6965 95 51 7 3945 15 35 3 1 28 2195 191 17 85 17 165 145 126 113 115 965 93 865 7 8 7 5 64 55 36 Rating (kg) 6735 6145 4895 4 3365 38 288 267 23 198 17 5 147 1365 127 5 122 117 965 855 7 45 695 64 59 53 465 45 33 NOTES: JIB CAPACITY IS LIMITED BY BOTH STRUCTURAL CAPACITY CHART AND MAIN CAPACITY CHART. SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING. OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY. 3 3 FRONT REAR 1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied. 2) The rated loads shown on outriggers do not exceed 8% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator. 3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See reduction chart. 4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting. 5) Ratings on rubber depend on 12.R2 tire capacity, condition of tires and proper inflation pressure (8,96 bar). Loads on rubber may be transported at a maximum seed of 4, km/h on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. For 36 ratings on rubber, rear axle oscillation locks must be in place. Do not use jib with crane on rubber. 6) For operating radius not shown, use load rating of next larger radius. 7) The maximum deck load only is 972 kg. Combined boom and deck loads are not permitted on rubber. 8) Do not induce any external side loads to boom or jib. THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. Grove YB552 The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 17

Rigging chart YB552 RIGGING CHART LOAD DISTRIBUTION CHART 1 -PART -1,lb WIRE ROPE: 9/16" Diameter 6 X 19 Bright Minimum required breaking strength =, lb YB552 (DIN/ISO) 1-PART -4536 kg RIGGING CHART 4-PART -4, lb MAXIMUM PERMISSIBLE SINGLE LINE PULL = 1, lb YB552 (Metric 85%) 1-PART -4536 kg RIGGING CHART 4-PART -18,1 kg WIRE ROPE: 14 mm Diameter 6 X 19 Bright. Minimum required breaking strength = 18,143 kg MAXIMUM PERMISSIBLE SINGLE LINE PULL = 4536 kg 4-PART -18,1 kg 1 CAB PIVOT HOLE PATTERN PIVOT 2 +8 LOW HEADROOM OPERATION (35 MAX. BOOM ANGLE; SINGLE PART LINE ONLY) Maximum Allowable Uniformly Distributed Load AREA 1 2 4,1 m (43.2 sq.ft.) 5985 kg (13,195 lb) AREA 2 2 2,15 m (23.1 sq.ft.) 387 kg (685 lb) TOTAL 2 6,16 m (66.3 sq.ft.) 972 kg (2, lb) 1. Maximum travel speed with any or all loads - 4, km/h (2.5 MPH) 2. Loads to be transported on smooth level firm surfaces only. 3. must be retracted and in center forward position. 4. Any combination or total of areas 1 and 2 may be used. 5. Lifting is not permitted when carry deck is loaded except for loading and unloading carry deck. 6. Rated pick and carry loads may be transported on deck area 1 provided the load is cribbed directly on the frame rails. WIRE ROPE: 14 mm Diameter 8 X Galv. Minimum required breaking strength = 19,867 kg +4 LOW HEADROOM OPERATION (55 MAX. BOOM ANGLE) MAXIMUM PERMISSIBLE SINGLE LINE PULL = 4536 kg -3 - STANDARD HEADROOM OPERATION (8 MAX. BOOM ANGLE) NO OFFSET JIB OPERATION (75 MAX. BOOM ANGLE) OFFSET J IB OPERATION (8 MAX. BOOM ANGLE) G7 1699 Rating reductions for load handling devices installed kg (lb) From main boom From jib block 161 kg (356 lb)* Not applicable Hook and ball 48 kg (15 lb)* 48 kg (15 lb) Jib stowed No reduction Not applicable 4,6 m (15 ft) jib deployed 317 kg (7 lb) No reduction 4,6 m - 7,6 m (15 ft - ft) jib deployed 5 kg (12 lb) No reduction *Refer to rating plate for actual weight 18 THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.

Symbols glossary Axles Counterweight Grade Outriggers Drive Heavy duty jib Radius elevation Electrical system Hoist Rotation extension Engine H Hookblock Speed length Extension Hydraulic system Steering nose Frame Lights Suspension Brakes Fuel tank capacity Oil Swing Cab Gear Outrigger controls Tires Transmission Grove YB552 19

Manitowoc Cranes Regional headquarters Americas Manitowoc, Wisconsin, USA Tel: +1 92 684 6621 Fax: +1 92 683 6277 Shady Grove, Pennsylvania, USA Tel: +1 717 597 8121 Fax: +1 717 597 462 Europe, Middle East, Africa Dardilly, France Tel: +33 ()4 72 18 2 2 Fax: +33 ()4 72 18 2 China Shanghai, China Tel: +86 21 6457 66 Fax: +86 21 6457 4955 Greater Asia-Pacific Singapore Tel: +65 6264 1188 Fax: +65 6862 Regional offices Americas Brazil Alphaville Mexico Monterrey Chile Santiago Europe, Middle East, Africa France Baudemont Cergy Decines Germany Langenfeld Italy Lainate Netherlands Breda Poland Warsaw Portugal Baltar Russia Moscow South Africa Johannesburg U.A.E. Dubai U.K. Buckingham China Beijing Chengdu Guangzhou Xian Greater Asia-Pacific Australia Brisbane Melbourne Sydney India Chennai Delhi Hyderabad Pune Korea Seoul Philippines Makati City Singapore Factories Brazil Passo Fundo China TaiAn Zhangjiagang France Charlieu Moulins Germany Wilhelmshaven India Pune Italy Niella Tanaro Portugal Baltar Fânzeres USA Manitowoc Port Washington Shady Grove This document is non-contractual. Constant improvement and engineering progress make it necessary that we reserve the right to make specification, equipment, and price changes without notice. Illustrations shown may include optional equipment and accessories and may not include all standard equipment. 214 Manitowoc Form No. YB552 PG Part No. 13-3 /PDF/114 www.manitowoccranes.com