INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory ACCESSORY HANDSFREELINK Application 2010 ACCORD 2 AND 4-DOOR Publications No. AII 42231 Issue Date AUG 2009 PARTS LIST HFL retainer HFL Attachment Kit P/N 08E02-TA0-100 HFL trim Template HFL bracket HFL harness Fuse label Fuse (2 A) HFL sub harness 7 EPT sealers (1 Not used) 2 Double-sided tapes A 26 Wire ties (4 Not used) Double-faced tape B (Some may not used) 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42231 (0908) 08E02-TA0-1000-91 1 of 25

4 Self-tapping screws, 3 x 10 mm HFL Kit P/N 08E00-E10-100 Switch 2 Washer screws, 4 x 10 mm Ground bolt Control unit Clip Accessory User s Information Manual 2 Bushings 2 Self-tapping screws (Black) Bumper rubber TOOLS AND SUPPLIES REQUIRED #2 Phillips screwdriver Flat-tip screwdriver Shop towel Diagonal cutters Ratchet 10 mm Socket 10 mm Combination wrench Utility Knife T15 Torques Felt-tip pen Tape Pushpin Drill 3 mm, 4.5 mm, 9 mm, and 10 mm Drill bit 20 mm Hole saw Wire 2 of 25 AII 42231 (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

Illustration of the HFL Installed on the Vehicle CONTROL UNIT HFL SWITCH Removing the vehicle parts 3. Disengage the eight retaining tabs and remove the left and right lens from the roof console. With Long Roof Console HFL SUB 4 RETAINING TABS SHOP TOWEL RIGHT LENS INSTALLATION 752905AB LEFT LENS 4 RETAINING TABS Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 1. Make sure you have the anti-theft code for the audio unit and the navigation system, then write down the radio presets. 2. Disconnect the negative cable from the battery. FLAT-TIP SCREWDRIVER With Short Roof Console 7302010B SHOP TOWEL 4 RETAINING TABS RIGHT LENS LEFT LENS 4 RETAINING TABS FLAT-TIP SCREWDRIVER 761802AB 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42231 (0908) 3 of 25

4. Open the sunglass holder. 5. Remove the two screws (Black) and the two screws (Silver) and let the roof console drop down. Disconnect the three vehicle connectors and remove the roof console. Long Roof Console 6. Turn the sunvisor holder 90, and remove the two sunvisor holders. SUNVISOR HOLDER CONNECTOR Turn. SUNVISOR HOLDERS SUNGLASS HOLDER Open. 2 SCREWS (Black) Short Roof Console 2 SCREWS (Silver) CONNECTORS 730202AB 7. Turn the left sunvisor toward the driver s door. 8. Locate the slot in the sunvisor holder, and insert a flat-tip screwdriver into the slot. Push in and hold the retaining tab. 9. While holding the retaining tab, push up on the left sunvisor holder and turn the left sunvisor back to its original position to remove it. If the retaining tab does not stay pushed in, return the sunvisor to its original position and repeat steps 7 and 9. HOLDER FLAT-TIP SCREWDRIVER 6D1806BY Push and hold tab. Rotate towards the door. SUNGLASS HOLDER Open. 2 SCREWS (Black) 2 SCREWS (Silver) 761803AB Push upward. LEFT SUNVISOR Turn rearward. 761804AB 4 of 25 AII 42231 (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

2-door model: Perform steps 10 and 11. 10. Pull away the weatherstrip from the left A-pillar trim. 11. Using a small rubber mallet and a shop towel, gently tap the left A-pillar trim at the SIDE CURTAIN AIRBAG mark to release the clip. Go to step 14. LEFT A-PILLAR 4-door model: Perform steps 12 and 13. 12. Pull away the weatherstrip from the left front A-pillar trim. 13. Using a small rubber mallet and a shop towel, gently tap the left A-pillar trim just below the SIDE CUR- TAIN AIRBAG mark. LEFT A-PILLAR PIN LEFT A-PILLAR TRIM CLIP STRIKE POINT SHOP TOWEL RUBBER MALLET PIN LEFT A-PILLAR TRIM CLIP STRIKE POINT SHOP TOWEL RUBBER MALLET WEATHERSTRIP CLIP LEFT A-PILLAR TRIM 732820AY WEATHERSTRIP CLIP LEFT A-PILLAR TRIM 711110AY 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42231 (0908) 5 of 25

14. Remove the left A-pillar trim (two clips). LEFT A-PILLAR TRIM 2 CLIPS 16. Remove the driver s dashboard lower cover (eight clips, two hooks, and disconnect the vehicle connector). CONNECTOR DRIVER S DASHBOARD LOWER COVER WEATHERSTRIP 2 HOOKS 6D18070Y 15. Remove and discard the clip from the left A-pillar trim, and install a new clip (supplied) on the left A-pillar trim. NEW CLIP 8 CLIPS 17. V6 Model only: Remove the driver s dashboard under cover (three clips and one pin). 6D1803AY 3 CLIPS CLIP (Discard.) LEFT A-PILLAR TRIM 6D18080Y PIN DRIVER S DASHBOARD UNDER COVER 6D18040Y 6 of 25 AII 42231 (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

18. Pull away the weatherstrip, then remove the left dashboard side cover (seven retaining tabs). 20. Pull up the front side of the left front door sill trim (four clips and retaining tab). 7 RETAINING TABS LEFT DASHBOARD SIDE COVER 4 CLIPS FRONT RETAINING TAB 3 HOOKS WEATHERSTRIP 6D1805BY 19. Remove the cover from the trunk lid/fuel fill door opener (two hooks and four retaining tabs), then remove one self-tapping screw. Make sure the trunk lid/fuel fill door opener is unlocked. LEFT FRONT DOOR SILL TRIM 21. Pull away the weatherstrip, and remove the left kick panel (two clips). WEATHERSTRIP 2 CLIPS 760501AE FRONT HOOKS COVER LEFT KICK PANEL 7111080Y SELF TAPPING SCREW 4 RETAINING TABS Unlock. KEY TRUNK LID/FUEL FILL DOOR OPENER 711104CY 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42231 (0908) 7 of 25

If the vehicle is M/T Model, continue with step 22; if not, go to step 24. M/T Model 22. Push down on the shift boot (two retaining tabs). Remove the shift knob by turning it counterclockwise. A/T Model 24. Remove the cup holder (12 clips and disconnect the vehicle connector). 12 CLIPS CUP HOLDER SHIFT KNOB 2 RETAINING TABS SHIFT BOOT Turn counterclockwise. 752101AY 23. Remove the center console panel (12 clips and disconnect the vehicle connector). Go to step 25. With Navigation, continue with step 25; Without Navigation, go to step 27. With Navigation 25. Remove the pocket (four bolts). CONNECTOR 7115010Y 12 CLIPS CENTER PANEL POCKET CONNECTOR 752102AY 4 BOLTS 752103AY 8 of 25 AII 42231 (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

26. Remove the CD changer (two bolts, two clips, and disconnect the vehicle connector). Go to step 28. 28. Remove the left lower cover (one clip and three clips). 2 CLIPS CONNECTOR 3 CLIPS 2 BOLTS Without Navigation CD CHANGER 27. Remove the pocket (four bolts). POCKET 752104AY CLIP 752805AB Installing the Control Unit and Routing the Harness If the vehicle is equipped with the long roof console, continue from step 29; if not, go to step 46. Long Roof Console 29. Using scissors, cut out template A and template B. For VINs beginning with 1HG: TEMPLATE A TEMPLATE Line a 4 BOLTS 711502BY TEMPLATE B 730205AB 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42231 (0908) 9 of 25

For VINs beginning with JHM: 31. Remove the roof console garnish from the roof console (four retaining tabs). TEMPLATE A TEMPLATE Line B 4 RETAINING TABS TEMPLATE B 752101AB 30. Remove the sunglass holder from the roof console (one screw, one spacer, and one spring). SUNGLASS HOLDER 32. Remove the console light from the roof console (four retaining tabs). GARNISH 733001BB SPRING 4 RETAINING TABS SCREW (Discard.) SPACER (Discard.) 730203CB LIGHT 733002AB 10 of 25 AII 42231 (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

If the VIN begins with 1HG, continue with step 33; if not, go to step 34. 36. While wearing eye protection, drill the two marked locations to 4.5 mm. Remove any burrs. 33. While wearing eye protection, widen the sunglass holder installation hole on the roof console with 9 mm drill bit. Make sure to drill at the correct position. DRILL BIT (4.5 mm) 2 MARKS DRILL BIT (9 mm) 752102AB 7302070B 37. Tape the template B to the roof console at the indicated position. 38. Using a pushpin, mark the roof console as indicated on the template. Using a felt-tip pen, mark the roof console around the template. Remove the template. 34. Tape the template A to the roof console at the indicated position. 35. Using a pushpin, mark the roof console as indicated on the template. Remove the template. PUSHPIN FELT-TIP PEN PUSHPIN 4 MARKS TEMPLATE B TAPE PUSHPIN 730208AB TEMPLATE A MARK TAPE 7302060B 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42231 (0908) 11 of 25

39. While wearing eye protection, drill the four marked locations to 20 mm. First drill with a 3 mm drill bit and finish with a 20 mm hole saw. 20 mm HOLE SAW DRILL BIT (3 mm) 42. Using isopropyl alcohol on a shop towel, clean the areas where the double-sided tape A will attach. Remove the adhesive backing from double-sided tape A and attach the double-sided tape A at the measurements shown. Remove the adhesive backing. DOUBLE-SIDED TAPE A 4 MARKS DRILL BIT (3 mm) CONTROL UNIT 10 mm Remove the adhesive backing. 20 mm HOLE SAW 730209AB 40. Using a utility knife, cut along the marking made on the roof console in step 38. After cutting, remove any burrs. 41. Reinstall the console light, garnish and unit to the roof console. Mark made in step 38. 10 mm 730211BB 43. Plug the HFL harness 22-pin connector into the control unit. 44. Using isopropyl alcohol on a shop towel, clean the areas where the double-sided tape A will attach. Remove the removing adhesive backing from the double-sided tape A and attach the control unit to the roof console as indicated. UTILITY KNIFE CONTROL UNIT CONTROL UNIT CENTER Cut out. 730210AB Remove the adhesive backing. HFL HFL 22-PIN CONNECTOR 730212AB 12 of 25 AII 42231 (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

45. Using the holes drilled in step 36 and secure the HFL bracket to the roof console with two 4 x 10 mm washer screws. Go to step 67. 47. Remove the sunglass holder from the roof console (two screws, two spacers, and one spring). SUNGLASS HOLDER SPRING SCREW (Discard.) SPACER (Discard.) 2 WASHER SCREWS, 4 x 10 mm Holes drilled in step 36. HFL BRACKET 7302130B With Short Roof Console 46. Using scissors, cut out template A and template B. SCREW (Discard.) 48. Remove the console light from the roof console (four retaining tabs). SPACER (Discard.) 752104BB TEMPLATE A TEMPLATE Line c 4 RETAINING TABS TEMPLATE B LIGHT 752105AB 752103AB 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42231 (0908) 13 of 25

If the VIN begins with 1HG, continue with step 49; if not, go to step 52. VINs beginning with 1HG: 49. While wearing eye protection, enlarge the sunglass holder installation hole on the roof console with 9 mm drill bit. Make sure to drill at the correct position. 50. Measure and pierce six location on the roof console with a pushpin as shown. Drill with 3 mm drill bit on six pierced points. Widen the hole with 10 mm drill bit. 5 mm 5 mm 5 mm 5 mm 5 mm 5 mm CENTER 5 mm 5 mm 5 mm 5 mm 5 mm 5 mm PUSHPIN DRILL BIT (9 mm) 752106AB DRILL DRILL BIT (3 mm 10 mm) 752901BB 51. Using an utility knife, cut along the marked line on the roof console. Go to step 54. UTILITY KNIFE MARKED LINE 752902BB 14 of 25 AII 42231 (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

VINs beginning with JHM: 52. Pierce six locations on the roof console with a pushpin as shown. Drill with 3 mm drill bit on six pierced points. Widen the hole using a 10 mm drill bit. 54. Tape the template A to the roof console at the indicated position. 55. Using a pushpin, mark the roof console as indicated on the template. Remove the template. PUSHPIN PUSHPIN TEMPLATE A DRILL DRILL BIT (3 mm 10 mm) 752903AB 53. Using a utility knife, cut along the marked line on the roof console. 2 MARKS TAPE 752107AB 56. While wearing eye protection, drill the two marked locations to 4.5 mm. Remove any burrs. DRILL BIT (4.5 mm) UTILITY KNIFE MARKED LINE 752904AB MARKS 752108AB 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42231 (0908) 15 of 25

57. Tape the template B to the roof console at the indicated position. 58. Using a pushpin, mark the roof console as indicated on the template. Using a felt-tip pen, mark the roof console around the template. Remove the template. 60. Using a utility knife, cut along the marking made on the roof console in step 58. After cutting, remove any burrs. 61. Reinstall the console light, garnish and unit to the roof console. PUSHPIN FELT-TIP PEN Mark made in step 58. 4 MARKS TEMPLATE B UTILITY KNIFE TAPE PUSHPIN Cut out. 752109AB 752111AB 59. While wearing eye protection, drill the four marked locations to 20 mm. First drill with a 3 mm drill bit and finish with a 20 mm hole saw. 20 mm HOLE SAW DRILL BIT (3 mm) DRILL BIT (3 mm) 62. Using isopropyl alcohol on a shop towel, clean the areas where the double-sided tape A will attach. Remove the adhesive backing from double-sided tape A and attach the double-sided tape A at the measurements shown. Remove the adhesive backing. 2 DOUBLE-SIDED TAPES A Remove the adhesive backing. 4 MARKS 20 mm HOLE SAW 752110AB CONTROL UNIT 10 mm 752112BB 16 of 25 AII 42231 (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

63. Plug the HFL harness 22-pin connector into the control unit. 64. Using isopropyl alcohol on a shop towel, clean the areas where the double-sided tapes A will attach. Remove the removing adhesive backing from the double-sided tape A and attach the control unit to the roof console as indicated. HFL HFL 22-PIN CONNECTOR 65. Using isopropyl alcohol on a shop towel, clean the areas where the double-sided tape B will attach. Attach a double-sided tape B to the HFL bracket. 66. Use the holes drilled in step 56 and secure the HFL bracket with two 4 x 10 mm washer screws to the roof console. CONTROL UNIT WASHER SCREWS, 4 x 10 mm CENTER Holes drilled in step 56. DOUBLE-SIDED TAPE B 10 mm Remove the adhesive backing. CONTROL UNIT 40 mm 752113AB HFL BRACKET Switch Installation Remove the adhesive backing. 752114AB 67. Push down the switch cover as shown and remove it. Remove the switch cover in the order shown. SWITCH COVER (Set aside) SWITCH COVER 1 SWITCH 3 Push down. 2 SWITCH 730214AB 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42231 (0908) 17 of 25

68. Insert the bumper rubber to the HFL retainer. 69. Assemble HFL retainer, switch, and HFL trim with four 3 x 10 mm self-tapping screws. With Long Roof Console With Short Roof Console HFL TRIM HFL TRIM SWITCH SWITCH HFL RETAINER HFL RETAINER 4 SELF-TAPPING SCREWS, 3 x 10 mm 4 SELF-TAPPING SCREWS, 3 x 10 mm HFL RETAINER HFL RETAINER BUMPER RUBBER 771012BB BUMPER RUBBER 730215BB 18 of 25 AII 42231 (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

70. Plug the HFL harness 20-pin connector into the switch. 71. Install the switch assembly in step 69 to the roof console with two self-tapping screws (Black) and two bushings. With Long Roof Console 72. Wrap two EPT sealers in the position shown to the HFL sub harness around the corrugated tube. HFL SUB SELF-TAPPING SCREW, 3 x 10 mm (Black) SWITCH END OF THE CORRUGATED TUBE BUSHING HFL 20-PIN CONNECTOR With Short Roof Console SELF-TAPPING SCREW, 3 x 10 mm (Black) HFL SWITCH BUSHING SELF- TAPPING SCREW, 3 x 10 mm (Black) 730216AB CORRUGATED TUBE 73. Wrap a wire to the sub harness as shown. Route a wire and pull the sub harness through the driver s dash board under cover opening to the left A-pillar opening. HFL SUB EPT SEALERS LEFT A-PILLAR OPENING 730217AB BRACKET BUSHING BUSHING DRIVER S DASHBOARD LOWER COVER OPENING HFL 20-PIN CONNECTOR SELF-TAPPING SCREW, 3 x 10 mm HFL (Black) 752115AB WIRE HFL SUB 3-PIN CONNECTOR TAPE DRIVER S DASHBOARD UNDER COVER OPENING 752116AB 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42231 (0908) 19 of 25

74. Route the HFL sub harness along the A-pillar, and align the green tape on the HFL sub harness with the vehicle clip. 75. Secure the HFL sub harness to the vehicle harness with one wire tie at this location. 76. Secure the HFL sub harness to the vehicle harness with the four wire ties. 78. With an assistant holding the roof console near the roof console opening, plug the HFL harness 3-pin connector into the HFL sub harness 3-pin connector, and secure the connector to the vehicle bracket with one wire tie. WIRE TIE BRACKET LINING CLIP GREEN TAPE ON HFL SUB WIRE TIE HFL SUB 3-PIN CONNECTOR Front 4 WIRE TIES HFL SUB GREEN CONNECTOR OPENING LEFT A-PILLAR HFL 3-PIN CONNECTOR 77. Route the HFL sub harness to the roof console opening. HFL SUB 7302190B OPENING 730221CB 79. Using isopropyl alcohol on a shop towel, clean the areas where the EPT sealers will attach. Under the roof liner, secure the HFL sub harness to the roof panel with four EPT sealers. EPT SEALERS LINING HFL SUB 730220AB LINING PANEL 7302220B 20 of 25 AII 42231 (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

80. Plug the vehicle connectors to the roof console. Reuse the two screws (Black) and the two screws (Silver) to reinstall the roof console. 82. Plug the HFL sub harness12-pin connector into the fuse box. CONNECTORS FUSE BOX FUSE BOX Front view Connection position HFL SUB 12-PIN CONNECTOR 2 SCREWS (Black; Reuse.) 2 SCREWS (Silver; Reuse.) 730223CB 81. Route the HFL sub harness down along the vehicle harness forward the fuse box as shown. Secure the HFL sub harness to the vehicle harness with two wire ties. 730225AB If another accessory is connected to the fuse box 12-pin connector, remove the dummy connector from the 12-pin connector of the accessory s harness and connect the 12-pin connector of the HFL subharness to the other accessory harness. HFL SUB DRIVER S DASHBOARD LOWER COVER OPENING FUSE BOX HFL SUB 12-PIN CONNECTOR WIRE TIES DUMMY CONNECTOR HFL SUB FUSE BOX 730224AB ACCESSORY 12-PIN CONNECTOR ACCESSORY 7214090E 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42231 (0908) 21 of 25

83. Remove the upper hood opener bolt, install the ground bolt with the HFL sub harness ground terminal into the upper hole of the hood opener, and tighten the ground bolt. 85. Install the 2 A fuse to the fuse box at the location shown. FUSE BOX Front view PANEL UPPER HOOD OPENER BOLT (Discard.) Connection position HOOD OPENER GROUND BOLT (Supplied.) HFL SUB GROUND TERMINAL 721410AE 2A FUSE FUSE BOX 730227AB 86. Attach the 2 A fuse label to the kick panel at the location shown. 84. Secure the HFL sub harness to the vehicle harness with two wire ties. FUSE BOX FUSE LABEL 2A FUSE LABEL WIRE TIES HFL SUB GROUND TERMINAL HFL SUB 730226BB 2 A FUSE LABEL 730228AB 22 of 25 AII 42231 (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

87. Route the HFL sub harness along the vehicle harness as shown. Loosely tighten it to the vehicle harness with three wire ties. FUSE BOX 89. Route the HFL sub harness as shown. Loosely tighten it to the vehicle harness with three wire ties. BRACKET HFL SUB HFL SUB WIRE TIES Loosely tighten. 752806BB 88. Route the HFL sub harness along the vehicle harness as shown. Loosely tighten it to the vehicle harness with two wire ties. STEERING TILT LEVER ACCELERATOR PEDAL 90. Route the HFL sub harness along the vehicle harness. Loosely tighten it to the vehicle harness with three wire ties. HFL SUB WIRE TIES Loosely tighten. 752808BB PARKING BRAKE STEERING SHAFT WIRE TIES Loosely tighten. HFL SUB 752807AB WIRE TIES Loosely tighten. 752809AB 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42231 (0908) 23 of 25

91. Disconnect the vehicle harness 1-pin connector and connect the HFL sub harness 1-pin connector in between. 93. Tighten three wire ties from step 90. HFL SUB PARKING BRAKE PARKING BRAKE 1-PIN CONNECTOR WIRE TIES HFL SUB 1-PIN CONNECTOR 1-PIN CONNECTOR 752810AB 92. Secure the HFL sub harness connection part with a wire tie. 94. Tighten three wire ties from step 89. BRACKET 752812AB HFL SUB PARKING BRAKE HFL SUB WIRE TIE HFL SUB CONNECTION PART 752811AB WIRE TIES 752813BB 24 of 25 AII 42231 (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

95. Tighten the three wire ties you attached in step 88. WIRE TIE STEERING TILT LEVER 97. Reconnect the connector. Insert the holder into the roof panel hole. Push up on the visor and rotate to its original position to lock into place. The connector should be tucked out of the visor holder. PANEL HOLE HFL SUB LOCK HFL SUB STEERING SHAFT WIRE TIE 752814AB LEFT SUNVISOR 96. Tighten the three wire ties you attached in step 87. HFL SUB 761902AB 98. Check that all wire harnesses are routed properly and all connectors are plugged in. 99. Reinstall all removed parts. Check that all clips and other fasteners are installed securely. 100. Reconnect the negative cable to the battery. 101. Enter the customer s radio anti-theft code, and reset the radio station presets. 102. Reset the clock. WIRE TIES 752815BB 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42231 (0908) 25 of 25