technosubtp series centrifugal auto prime trash pumps
4tSTap standard trash auto prime FEATURES Technosub Standard Trash Auto Prime pumps are specifically designed to effectively handle a wide range of liquids from water to sewage and sludge that can contain solids and other material. Technosub Standard Trash Auto Prime pumps provide a dependable, highly efficient solution in a completely automatic priming pump. The model 4TSTAP is capable of achieving maximum flows of 12 gpm (284 m³/hr) and maximum total head of 116 (35 m) while handling solids up to 3 (75 mm) in diameter. The standard 4TSTAP is powered by a watercooled, 4-cylinder diesel engine. Alternative drives are available, including other diesel engines or electric motor options. - Technosub s rugged, heavy duty pumps are engineered specifically for portable application - Fully automatic priming system allows the pump to prime and re-prime while running - Compressor-fed, venturi priming system provides rapid, reliable priming - Mechanical seal with biodegradable glycol quench allows the pump to start and run dry - Non-return valve uses only a single moving part to allow full flow with minimal restriction - Pump casings are hydrostatically tested to psig (345 kpa) above the peak casing design pressure - Standard engine control panel provides preset emergency shutdown protection and allows the addition of automatic level control - Skid-mounted formats with tie downs, lifting bail, and fork pockets Options - Fuel tanks for extended run times and/or remote location - Modular trailer kit - Trailer brakes and lights - Sound attenuated enclosure - Hose racks, accessory containers and other custom features available - Wide range of suction and discharge fittings including Technosub s own QD Quick Disconnect fittings and accessories
4tstapstandard trash auto prime 131.88 (3349.63) 141.88 (3603.63) 76. (1943.19) 36.47 (926.) 40.00 (1016.00) 71.75 (1822.45) 20.00 (8.00) 83.00 (2108.20) 83.00 (2108.20) 75 1 m³/hr 1 175 200 2 2 275 120 2200 rpm 35 110 2000 rpm 90 80 70 60 1800 rpm 1600 rpm 20 meters 1400 rpm 15 40 10 200 0 400 0 600 700 US gpm 800 900 0 1 1200 specifications - Connections: 4 ( mm) ANSI Flanges - Maximum Pump Speed: 2200 rpm - Maximum Flow: 12 gpm (284 m 3 /h) - Maximum Head: 116 (35 m) - Maximum Static Priming Lift: 28 (8.5 m) - Water Temperature Limit: 160 F (70 C) - Solids Handling Capability: 3 (75 mm) - Maximum Casing Pressure: 1 psig (862 kpa) - Fuel Tank: 110 gallons (416 liters) pump materials - Casing: Cast Iron (CD4MCu is an option) - Impeller: Cast Iron (CD4MCu is an option) - Bearing Housing: Cast Iron - Bearing Lubrication: Grease - Shaft: Steel - Seal: Silicon Carbide on Silicon Carbide - Chassis/Fuel Cell: Steel - Non-Return Valve: Nitrile Fitted Cast Iron Specifications and illustrations are subject to revision without notice. Technosub is not liable for any consequential, incidental or indirect damages relating to these specifications. 1 866 797-30 technosub.net
6tSTap standard trash auto prime FEATURES Technosub Standard Trash Auto Prime pumps are specifically designed to effectively handle a wide range of liquids from water to sewage and sludge that can contain solids and other material. Technosub Standard Trash Auto Prime pumps provide a dependable, highly efficient solution in a completely automatic priming pump. The model 6TSTAP is capable of achieving maximum flows of 27 gpm (6 m³/h) and maximum total head of 165 ( m) while handling solids up to 3 (75 mm) in diameter. The standard 6TSTAP is powered by a watercooled, 4-cylinder diesel engine. Alternative drives are available including natural gas as well as electric motors. - Technosub s rugged, heavy duty pumps are engineered specifically for portable application - Fully automatic priming system allows the pump to prime and re-prime while running - Compressor-fed, venturi priming system provides rapid, reliable priming - Mechanical seal with biodegradable glycol quench allows the pump to start and run dry - Non-return valve uses only a single moving part to allow full flow with minimal restriction - Pump casings are hydrostatically tested to psig (345 kpa) above the peak casing design pressure - Standard engine control panel provides preset emergency shutdown protection and allows the addition of automatic level control - Skid-mounted formats with tie downs, lifting bail, and fork pockets Options - Fuel tanks for extended run times and/or remote location - Modular trailer kit - Trailer brakes and lights - Sound attenuated enclosure - Hose racks, accessory containers and other custom features available - Wide range of suction and discharge fittings including Technosub s own QD Quick Disconnect fittings and accessories
6tstapstandard trash auto prime 156. (3975) 102.00 (91) 156. (3975) 89.54 (2274) 38.27 (972) 73.00 (1854) 78. (1988) 54.38 (1381) 46. (1181) 23. (591) 102.00 (91) drawing shown with optional modular trailer kit 97.63 (2480) 1 200 2 0 m³/hr 3 400 4 0 5 600 6 2000 rpm 1 1900 rpm 1 1800 rpm 1700 rpm 40 1600 rpm meters 75 20 2 0 7 0 12 10 US gpm 17 2000 22 20 27 10 specifications - Connections: 6 (1 mm) ANSI Flanges - Maximum Pump Speed: 2000 rpm - Maximum Flow: 27 gpm (6 m 3 /h) - Maximum Head: 165 ( m) - Maximum Static Priming Lift: 28 (8.5 m) - Water Temperature Limit: 160 F (70 C) - Solids Handling Capability: 3 (75 mm) - Maximum Casing Pressure: 1 psig (862 kpa) - Fuel Tank: 110 gallons (416 liters) pump materials - Casing: Cast Iron (CD4MCu is an option) - Impeller: Cast Iron (CD4MCu is an option) - Bearing Housing: Cast Iron - Bearing Lubrication: Grease - Shaft: Steel - Seal: Silicon Carbide on Silicon Carbide - Chassis/Fuel Cell: Steel - Non-Return Valve: Nitrile Fitted Cast Iron Specifications and illustrations are subject to revision without notice. Technosub is not liable for any consequential, incidental or indirect damages relating to these specifications. 1 866 797-30 technosub.net
8tSTap standard trash auto prime FEATURES Technosub Standard Trash Auto Prime pumps are specifically designed to effectively handle a wide range of liquids from water to sewage and sludge that can contain solids and other material. Technosub Standard Trash Auto Prime pumps provide a dependable, highly efficient solution in a completely automatic priming pump. The model 8TSTAP is capable of achieving maximum flows of 3400 gpm (772 m³/h) and maximum total head of 165 ( m) while handling solids up to 4 ( mm) in diameter. The standard 8TSTAP is powered by a watercooled, 4-cylinder diesel engine. Alternative drives are available including natural gas as well as electric motors. - Technosub s rugged, heavy duty pumps are engineered specifically for portable application - Fully automatic priming system allows the pump to prime and re-prime while running - Compressor-fed, venturi priming system provides rapid, reliable priming - Mechanical seal with biodegradable glycol quench allows the pump to start and run dry - Non-return valve uses only a single moving part to allow full flow with minimal restriction - Pump casings are hydrostatically tested to psig (345 kpa) above the peak casing design pressure - Standard engine control panel provides preset emergency shutdown protection and allows the addition of automatic level control - Skid-mounted formats with tie downs, lifting bail, and fork pockets Options - Fuel tanks for extended run times and/or remote location - Modular trailer kit - Trailer brakes and lights - Sound attenuated enclosure - Hose racks, accessory containers and other custom features available - Wide range of suction and discharge fittings including Technosub s own QD Quick Disconnect fittings and accessories
8tstapstandard trash auto prime 156. (3975) 102.00 (91) 156. (3975) 89.54 (2274) 22.44 (570) 38.99 (990) 73.00 (1854) 78. (1988) 59.88 (1521) 46. (1181) 23. (591) 102.00 (91) Estimated Dry Weight = 5,200 lbs (2,359 kg) drawing shown with optional modular trailer kit 97.63 (2480) 0 10 20 40 60 70 80 90 110 l/s 120 1 140 1 160 170 180 190 200 210 220 2 0 1 200 2 0 3 m³/hr 400 4 0 5 600 6 700 7 800 1900 rpm 1 1800 rpm 1 1600 rpm 40 1400 rpm meters 75 1200 rpm 20 10 2 0 7 specifications 0 12 10 17 2000 22 20 27 US gpm pump materials 00 32 - Connections: 8 (200 mm) ANSI Flanges - Maximum Pump Speed: 1900 rpm - Maximum Flow: 3400 gpm (772 m 3 /h) - Maximum Head: 165 ( m) - Maximum Static Priming Lift: 28 (8.5 m) - Water Temperature Limit: 160 F (70 C) - Solids Handling Capability: 4 ( mm) - Maximum Casing Pressure: 1 psig (862 kpa) - Fuel Tank: 110 gallons (416 liters) - Casing: Cast Iron (CD4MCu is an option) - Impeller: Cast Iron (CD4MCu is an option) - Bearing Housing: Cast Iron - Bearing Lubrication: Grease - Shaft: Steel - Seal: Silicon Carbide on Silicon Carbide - Chassis/Fuel Cell: Steel - Non-Return Valve: Nitrile Fitted Cast Iron Specifications and illustrations are subject to revision without notice. Technosub is not liable for any consequential, incidental or indirect damages relating to these specifications. 1 866 797-30 technosub.net
12tSTap standard trash auto prime FEATURES Technosub Standard Trash Auto Prime pumps are specifically designed to effectively handle a wide range of liquids from water to sewage and sludge that can contain solids and other material. Technosub Standard Trash Auto Prime pumps provide a dependable, highly efficient solution in a completely automatic priming pump. The model 12TSTAP is capable of achieving maximum flows of 80 gpm (1886 m³/h) and maximum total head of 117 (35 m) while handling solids up to 4 ( mm) in diameter. The standard 12TSTAP is powered by a watercooled, 6-cylinder diesel engine. Alternative drives are available, including other diesel engines or electric motor options. - Technosub s rugged, heavy duty pumps are engineered specifically for portable application - Fully automatic priming system allows the pump to prime and re-prime while running - Compressor-fed, venturi priming system provides rapid, reliable priming - Fully guarded coupling - Mechanical seal with biodegradable glycol quench allows the pump to start and run dry - Non-return valve uses only a single moving part to allow full flow with minimal restriction - Pump casings are hydrostatically tested to psig (345 kpa) above the peak casing design pressure - Standard engine control panel provides preset emergency shutdown protection and allows the addition of automatic level control - Skid-mounted formats with tie downs, lifting bail, and fork pockets Options - Technosub s Environmental Box captures venturi blow by, separates and silences air exhaust and returns liquid to the pump suction. - Fuel tanks for extended run times and/or remote location as required - Highway trailer with integral fuel cell/chassis, lights, fenders, tie downs, lifting bail, front and rear jacks - Trailer brakes can be offered as required - Sound attenuated enclosure options - Hose racks, accessory containers and other custom features available as required - Wide range of suction and discharge fittings including Technosub s own QD Quick Disconnect fittings and accessories
12tstapstandard trash auto prime m 3 /h 200 0 400 0 600 700 800 900 0 1 1200 10 1400 10 1600 1700 1800 1900 1200 rpm 35 1 rpm 0 rpm Head - ft 75 900 rpm 20 meters 800 rpm 15 10 0 0 10 2000 20 00 4000 40 00 50 6000 60 7000 70 8000 80 US gpm specifications - Connections: 12 (0 mm) ANSI Flanges - Maximum Pump Speed: 1200 rpm - Maximum Flow: 80 gpm (1886 m 3 /h) - Maximum Head: 117 (35 m) - Maximum Static Priming Lift: 28 (8.5 m) - Water Temperature Limit: 160 F (70 C) - Solids Handling Capability: 4 ( mm) - Maximum Casing Pressure: 1 psig (862 kpa) - Fuel Tank: 215 gallons (814 liters) pump materials - Casing: Cast Iron (CD4MCu is an option) - Impeller: Cast Iron (CD4MCu is an option) - Bearing Housing: Cast Iron - Bearing Lubrication: Grease - Shaft: Steel - Shaft sleeve: Stainless Steel - Seal: Silicon Carbide on Silicon Carbide - Chassis/Fuel Cell: Steel - Non-Return Valve: Nitrile Fitted Cast Iron - Environmental Box (Optional): Steel Specifications and illustrations are subject to revision without notice. Technosub is not liable for any consequential, incidental or indirect damages relating to these specifications. 1 866 797-30 technosub.net
18tSTap standard trash auto prime FEATURES Technosub Standard Trash Auto Prime pumps are specifically designed to effectively handle a wide range of liquids from water to sewage and sludge that can contain solids and other material. Technosub Standard Trash Auto Prime pumps provide a dependable, highly efficient solution in a completely automatic priming pump. The model 18TSTAP is capable of achieving maximum flows of 120 gpm (2840 m 3 /h) and maximum total head of 138 (42 m) while handling solids up to 4 ( mm) in diameter. The standard 18TSTAP is powered by a watercooled, 6-cylinder diesel engine. Alternative drives are available, including other diesel engines or electric motor options. - Technosub s rugged, heavy duty pumps are engineered specifically for portable application - Fully automatic priming system allows the pump to prime and re-prime while running - Compressor-fed, venturi priming system provides rapid, reliable priming - Fully guarded coupling - Mechanical seal with biodegradable glycol quench allows the pump to start and run dry - Non-return valve uses only a single moving part to allow full flow with minimal restriction - Pump casings are hydrostatically tested to psig (345 kpa) above the peak casing design pressure - Standard engine control panel provides preset emergency shutdown protection and allows the addition of automatic level control - Skid-mounted formats with tie downs, lifting bail, and fork pockets Options - Technosub s Environmental Box captures venturi blow by, separates and silences air exhaust and returns liquid to the pump suction. - Fuel tanks for extended run times and/or remote location as required - Highway trailer with integral fuel cell/chassis, lights, fenders, tie downs, lifting bail, front and rear jacks - Trailer brakes can be offered as required - Sound attenuated enclosure options - Hose racks, accessory containers and other custom features available as required - Wide range of suction and discharge fittings including Technosub s own QD Quick Disconnect fittings and accessories
18tstapstandard trash auto prime m 3 /h 1200 rpm 75 1 1 175 200 2 2 275 1 1 rpm 40 35 0 rpm Head -ft 75 900 rpm 800 rpm 20 meters 15 10 0 2000 00 4000 00 6000 7000 8000 9000 00 10 12000 100 specifications - Connections: 18 (4 mm) suction x 14 (356 mm) discharge ANSI Flanges - Maximum Pump Speed: 1200 rpm - Maximum Flow: 120 gpm (2840 m 3 /h) - Maximum Head: 138 (42 m) - Maximum Static Priming Lift: 28 (8.5 m) - Water Temperature Limit: 160 F (70 C) - Solids Handling Capability: 4 ( mm) - Maximum Casing Pressure: 1 psig (862 kpa) - Fuel Tank: 2 gallons (946 liters) pump materials - Casing: Cast Iron (CD4MCu is an option) - Impeller: Cast Iron (CD4MCu is an option) - Bearing Housing: Cast Iron - Bearing Lubrication: Grease - Shaft: Steel - Shaft sleeve: Stainless Steel - Seal: Silicon Carbide on Silicon Carbide - Chassis/Fuel Cell: Steel - Non-Return Valve: Nitrile Fitted Cast Iron - Environmental Box (Optional): Steel Specifications and illustrations are subject to revision without notice. Technosub is not liable for any consequential, incidental or indirect damages relating to these specifications. 1 866 797-30 technosub.net
CD4MCu BENEFITS cd4mcu corrosive and abrasive applications - Corrosion and pitting resistance - Higher strength than standard stainless steel - Improved ductility and weldability - Better resistance to embrittlement applications Pump wet end components made in CD4MCu offer superior corrosion resistance, hardness, and impact properties that make the alloy highly abrasion resistant in applications where pumps are subject to abrasive wear and chemical corrosion. Technosub offers CD4MCu as an option for its entire Auto Prime line of efficient, rugged, heavy duty pumps. Popular models in stock. Contact us for more information. Superior corrosion and abrasion ability make CD4MCu ideal for varied applications in these industries: - Mining - Industrial Process - Chemical / Petrochemical - Oil and Gas - Marine - Manufacturing - Paper and Pulp - Municipal - Food Processing - Fertilizer Technosub provides its full line of outstanding Trash and High Head pumps in CD4MCu, a high grade duplex stainless steel, for applications where corrosion and/or abrasion are a concern. CD4MCu is an Fe-Cr-Ni-Cu-Mo alloy with a duplex structure of ferrite and austenite. Moderately high strength and hardness are combined with good ductility and impact properties, resulting in an alloy with superior resistance to abrasion or erosion-corrosion. CD4MCu provides significantly better stress/corrosive cracking resistance, and less pitting than standard stainless steel. It has a higher strength and thus is more durable. Many factors must be evaluated when selecting pump end component materials including the liquid being pumped, specific gravity and ph level, GPM, Total Dynamic Head, pump type and speed, and whether the pump will run intermittent or continuous. Technosub engineers can help select the best solution for your application. specifications Standard Trash Auto Prime (TSTAP) - Max Flows from 12 to 120 gpm (284 to 2840 m³/hr) - Max Head from 116 to 165 ft (35 to m) High Trash Auto Prime (THTAP) - Max Flows from 1600 to 16000 gpm (363 to 3634 m³/hr) - Max Head from 174 to 238 ft (53 to 73 m) Standard High Head Auto Prime (TSHAP) - Max Flows from 1 to 40 gpm (2 to 1022 m³/hr) - Max Head from 3 to 380 ft (101 to 116 m) Hyper High Head Auto Prime (THHAP) - Max Flows from 4 to 7000 gpm (97 to 1590 m³/hr) - Max Head from 520 to 606 ft (159 to 185 m) Specifications and illustrations are subject to revision without notice. Technosub is not liable for any consequential, incidental or indirect damages relating to these specifications. 1 866 797-30 technosub.net
sound attenuated enclosure FEATURES - Standard Sound Attenuated Units reduce noise emissions to no more than 70 db at feet (9 meters) - Large, lockable doors provide easy access to the interior for operational controls, routine service and fueling - The entire enclosure, its individual panels and all doors are removable to allow complete access during maintenance or major overhauls - Technosub s innovative Environmental Box captures venturi blow by, separates and silences the air exhaust and returns liquid to the pump suction - DOT approved highway trailer with front and rear jacks, fenders and lights is an available option Technosub sound attenuated enclosures are ideally suited for operations in residential and other areas where noise reduction is an important consideration. Made of 12-gauge Galvannealed-Steel (or optional stainless steel), panels are insulated with a 1-1/4 inch thick fire retardant acoustical foam to reduce noise level to no more than 70 db at feet (9m). Custom db levels are available to meet design requirements. - Wide range of suction and discharge fittings including Technosub s own QD Quick Disconnect fittings and accessories - Technosub s Sound Attenuated Trash Auto Prime (TAP) pumps provide an economical, dependable and highly efficient automatic self-priming pumping solution enclosed in a neat and quiet enclosure - Other Technosub models of pumps, including Trash Vacuum Prime (TVP), High-Pressure Auto Prime (HAP), Centrifugal Wellpoint (CWP) and Rotary Wellpoint (RWP) are available with Sound Attenuated Enclosure options Designed for upward exhaust of combustion gases and cooling air. Panels are removable for maintenance and repair. Panel doors, with locks, provide easy access to the pump, engine, priming system, and controls for routine servicing, lubrication, and fueling. Specifications and illustrations are subject to revision without notice. Technosub is not liable for any consequential, incidental or indirect damages relating to these specifications. 1 866 797-30 technosub.net