INSTLLTION INSTRUTIONS FOR PRT 99-786 PPLITIONS Honda Pilot 00-008 006-008 (Without Factory Navigation) 99-786 KIT FETURES Recessed DIN Pocket ISO Head Unit Provision With Pocket KIT OMPONENTS ) L Radio Housing ) E Radio Housing ) Pocket D) Rear Support racket E) ISO rackets F) ISO Trimplate G) () # 8x/8 Phillips Truss Head Screws H) () # 8x/8 Phillips Pan Head Screws D E F G H WIRING ND NTENN ONNETIONS (Sold Separately) Harness: 70-7 - Honda/cura harness 998-up ntenna dapter: 40-HD0 - Honda antenna adapter 005-up TOOLS REQUIRED: Small Flat lade Screwdriver/ Panel Removal Tool Phillips Screwdriver Socket Set -800--09 www.metraonline.com OPYRIGHT 004-009 METR ELETRONIS ORPORTION REV. 06-9-09
99-786 TLE OF ONTENTS Dash Disassembly Honda Pilot 00-008................................. Honda Pilot 006-008 (Without Factory Navigation).......... Kit ssembly....................................... DIN Head Unit Provision With Pocket...................... 4 ISO Head Unit Provision With Pocket...................... 5 Final ssembly........................................6 KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-54-678 for more information and take steps toward a better tomorrow.
99-786 DSH DISSSEMLY HOND PILOT 00-008 Disconnect the negative battery terminal to prevent an accidental short circuit. Using a small flat blade screwdriver remove the blank plate from upper right side of radio trim panel. (Figure ) Unsnap radio trim panel. Unplug switches and remove panel. (Figure ) 4 Remove (4)0mm bolts securing radio, unplug and remove radio. (Figure )
99-786 DSH DISSSEMLY HOND PILOT 006-008 (Without Factory Navigation) Disconnect the negative battery terminal to prevent an accidental short circuit. Remove () screws from the top of the instrument panel trim. Unclip and remove the instrument panel trim. (Figure ) 4 5 Unclip and remove the left center trim panel. (Figure ) Unclip the radio trim panel. Unplug and remove the panel. (Figure ) Remove the (4) screws securing the radio. Unplug and remove the radio. (Figure D) ontinue to kit assembly. D
99-786 KIT SSEMLY HOND PILOT 00-008 006-008 (Without Factory Navigation) Select the proper radio housing for your vehicle. EX models use radio housing (E) and LX models use radio housing (L). The radio housings are labeled on one of the mounting tabs. (Figure ) Mount the pocket to the back of the radio housing with the () #8x/8 phillips pan head screws supplied. (Notches on the pocket must be on top.) (Figure ) Mount the rear support bracket to the back of the pocket with the () #8x/8 Phillips truss head screws supplied. (Figure )
99-786 KIT SSEMLY DIN HED UNIT PROVISION WITH POKET Slide DIN cage (supplied with radio) into the assembled radio housing from the front. (Figure ) Secure DIN cage to radio housing by bending the locking tabs outward. (Figure ) Slide the radio into the DIN cage until it snaps into place. (Figure ) 4
99-786 KIT SSEMLY ISO HED UNIT PROVISION WITH POKET lign the holes in the ISO brackets with the holes in the radio. Mount the brackets to the radio using screws supplied with the radio. (Figure ) Slide the radio/bracket assembly into the assembled radio housing until it snaps into place. (Figure ) Snap the ISO trimplate onto the front of the assembled radio and housing. (Figure ) NOTE: To remove the radio unsnap and remove the ISO trimplate. Using a flat blade screwdriver disengage ISO brackets from the radio housing and slide radio out of radio housing. 5
99-786 FINL SSEMLY FINL SSEMLY ) Strip wire ends back /" ) Twist ends together ) Solder D) Tape D Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disassembly. FINL WIRING ONNETIONS Make wiring connections using the EI color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit. METR / EI WIRING ODE V Ignition / cc... Red Dimmer.......... Orange / White V att / Memory.. Yellow Right Front (+)..... White Ground........... lack* Left Front (-)....... White / lack Power ntenna..... lue Right Rear (+)...... Violet mp Turn-On...... lue / White Right Rear (-)...... Violet / lack mp Ground....... lack / White Left Rear (+)....... Green Illumination........ Orange Left Rear (-)....... Green / lack *NOTE: When lack a wire is not present, ground radio to vehicle chassis. ll colors may not be present on all leads due to manufacturer s specifications. -800--09 www.metraonline.com Rev. 06/9/09 OPYRIGHT 004-009 METR ELETRONIS ORPORTION INST99-786 6