INSTLLTION INSTRUTIONS FOR PRT 99-80 PPLITIONS Toyota Tundra 007-008 Sequoia 008 99-80 KIT FETURES DIN Radio Provision with Pocket ISO Mount Radio Provision with Pocket Double DIN Radio Provision Stacked ISO Mount Units Provision KIT OMPONENTS ) Radio Housing ) ISO rackets ) ISO Trim Plate D) Double DIN rackets E) Double DIN Trim Plate F) Pocket D E F TOOLS REQUIRED: Small Flat lade Screwdriver/ Panel Removal Tool Phillips Screwdriver Socket Set -800--09 www.metraonline.com OPYRIGHT 007-009 METR ELETRONIS ORPORTION
99-80 TLE OF ONTENTS Dash Disassembly - Toyota Tundra (onsole Shift ) 007-008............., - Toyota Sequoia 008..., - Toyota Tundra (olumn Shift ) 007-008............. - Toyota Sequoia 008... Kit ssembly - DIN Radio Provision with Pocket.............................4 - ISO Mount Radio Provision with Pocket........................5 - Double DIN Radio Provision................................ 6 - Stacked ISO Mount Units Provision...........................7 Final ssembly...........................................8 *Note: Refer also to the instructions included with the aftermarket radio. KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-54-678 for more information and take steps toward a better tomorrow.
99-80 DSH DISSSEMLY TOYOT TUNDR (onsole Shift) 007-008 TOYOT SEQUOI 008 Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip and remove the top trim panel around cup holders. (Figure ) Remove () Phillips screw from shifter trim panel and remove panel. (Figure ) 4 Unclip, unplug and remove the climate control assembly. (Figure ) ontinue dash disassembly.
99-80 DSH DISSSEMLY 5 6 TOYOT TUNDR (onsole Shift) 007-008 Remove (4) 0 MM bolts securing the radio. (Figure D) Unclip the right side of the instrument panel trim and pull back the trim,then unclip,unplug and remove radio. (Figure E) ontinue to kit assembly. TOYOT SEQUOI 008 D E
99-80 DSH DISSSEMLY TOYOT TUNDR (olumn Shift) 007-008 TOYOT SEQUOI 008 4 5 6 7 Disconnect the negative battery terminal to prevent an accidental short circuit. Remove () plastic Phillips screws one from each side of the trim panel below the cup holder then unclip and remove the panel. (Figure ) Pull the cup holder out and depress the () clips on each side to slide cup holder out of cup holder panel. (Figure ) Remove (4) Phillips screws from cup holder panel assembly then unclip and remove assembly. (Figure ) Unclip and remove the climate control assembly. (Figure D) Remove (4) 0 MM bolts securing the radio. Unclip the right side of the instrument panel trim and pull back then unclip and remove radio. ontinue to kit assembly. D
99-80 KIT SSEMLY DIN MOUNT RDIO PROVISION WITH POKET *Note: Refer also to the instructions included with the aftermarket radio. Slide the DIN cage into the radio housing and secure by bending the metal locking tabs outward. (Figure ) Slide the aftermarket radio into the cage until it snaps into place. (Figure ) Snap the pocket into the radio housing. (Figure ) ontinue to final assembly. 4
99-80 KIT SSEMLY ISO MOUNT RDIO PROVISION WITH POKET *Note: Refer also to the instructions included with the aftermarket radio. Mount the ISO rackets to the radio using the screws supplied with the radio. (Figure ) Slide the radio into the radio housing until it snaps into place. (Figure ) Snap the trim plate onto the front of the Radio/Housing assembly. (Figure ) 4 Snap the Pocket into the radio housing. (Figure D) ontinue to final assembly. D 5
99-80 KIT SSEMLY DOULE DIN RDIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. ut and remove the center bar from the radio housing. (Figure ) Snap the Double DIN brackets to the inside edge of the radio housing. (Figure ) Slide the Double DIN radio into the bracket/radio housing assembly and secure the radio to the assembly using the screws supplied with the radio. (Figure ) 4 Snap the Double DIN trim plate onto the front of the radio/housing assembly. (Figure ) ontinue to final assembly. 6
99-80 KIT SSEMLY STKED ISO MOUNT UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. ut and remove the center bar from the radio housing. (Figure ) Snap the Double DIN brackets to the inside edge of the radio housing. (Figure ) Slide the stacked ISO mount units into the bracket/housing assembly and secure the units to the assembly using the screws supplied with the units. (Figure ) 4 Snap the Double DIN trim plate onto the front of the radio/housing assembly. (Figure ) ontinue to final assembly. 7
99-80 FINL SSEMLY FINL SSEMLY () Strip wire ends back /" ) Twist ends together ) Solder D) Tape D Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disassembly. FINL WIRING ONNETIONS Make wiring connections using the EI color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit. METR / EI WIRING ODE V Ignition / cc.......... Red V att / Memory......... Yellow Ground.................. lack* Power ntenna............ lue mp Turn-On............. lue / White mp Ground.............. lack / White Illumination.............. Orange Dimmer................. Orange / White Right Front (+)............ Gray Right Front (-)............. Gray/ lack Left Front (+)............. White Left Front (-).............. White / lack Right Rear (+)............ Violet Right Rear (-)............. Violet / lack Left Rear (+)............. Green Left Rear (-).............. Green / lack *NOTE: When a lack wire is not present, ground radio to vehicle chassis. ll colors may not be present on all leads due to manufacturer s specifications. 8
99-80 NOTES 9
99-80 INSTRUTIONS -800--09 www.metraonline.com REV. 0/6/09 OPYRIGHT 007-009 METR ELETRONIS ORPORTION INST99-80