INSTRUCTION MANUAL CONVERTIBLE BOOSTER SEAT Suitable for 6 month to approx 8 years of age or until the child s shoulders reach the upper height marker Model: GM 2010 & GMA 2010 Illustrations are representative only. Design and style may vary. IMPORTANT: KEEP THIS BOOKLET IN THE PLACE PROVIDED ON THE CHILD RESTRAINT
Before You Start Thank you for purchasing this child seat. This product is suitable for toddlers and older children. We welcome you as a valued customer, and trust that your child will enjoy many years of comfort and safety. No child restraint can guarantee absolute protection from a crash. However proper use of this restraint may reduce the risk of injury or death! Table of Contents Page Page Page Page Page Page 3-5 Warnings 6 Warnings To Parents And Other Users 7-10 Anchorage Fitting Installation 11 Correct Vehicle Position 12 Tether Strap / Headrest Adjustments 13 Reclining Backrest Page 14-15 Features For Toddler Mode Page 16-20 Preparation For Use Toddler Page 21 Correct Shoulder Height Marker Page 22-23 Features For Booster Mode Page 24 Remove Harness System Page 25-26 Installation For Booster Mode Page 27 The next seat for your child Page 28-31 Care And Maintenance 2
WaRnInG IMPORTANT: RETAIN FOR FUTURE REFERENCE THESE INSTRUCTIONS DETAIL THE SAFE USE, FITMENT AND MAINTENANCE OF THE SEAT. PLEASE READ THESE INSTRUCTIONS CAREFULLY AND ENSURE THAT THEY ARE FOLLOWED AT ALL TIMES. NO SAFETY SEAT CAN GUARANTEE PROTECTION FROM INJURY HOWEVER, PROPER USE OF THIS SEAT REDUCES THE RISK OF SERIOUS INJURY OR DEATH TO YOUR CHILD. THIS RESTRAINT MUST BE ATTACHED TO A CHILD RESTRAINT ANCHORAGE POINT IN THE CAR. REFER TO CAR OWNER S HANDBOOK FOR LOCATION OF ANCHORAGE POINTS. REFER TO A CHILD RESTRAINT FITTING STATION IF NO ANCHORAGE POINTS ARE IN THE MOTOR CAR. Follow the manufacturer s instructions at all times. Use the restraint exactly as shown in the instructions. To be used in forward-facing position by children whose shoulders are above the lower shoulder height marker (approximately 6 months of age) until their shoulders reach the middle shoulder height marker (approximately 4 years of age). Then to be used with a lap-sash seatbelt until their shoulders reach the upper shoulder height marker (approximately 6 to 8 years of age). Continue to use this child restraint until the child reaches this limit. Children are safest in a booster seat until their shoulders reach the upper shoulder height marker of the booster seat. Do not use this restraint until child s shoulders are above the lower shoulder height marker. Just using a seatbelt is not recommended for children that have outgrown this seat. Use a larger booster seat. 3
General WaRnInG Supervision of children is needed because they may be able to undo buckles. Use the restraint exactly as shown in the instructions. Do not alter or modify this restraint. Repairs must only be done by the manufacturer or agent. Do not allow the restraint to come into contact with polishes, oils, bleach and other chemicals. Destroy the restraint if it has been in a severe crash, even if no damage is visible. Straps may be damaged by unsecured cargo in a collision. Secure or remove hazardous cargo before using this restraint. Hatch-back or Wagon: Do not use the child restraint where this strap may fall into a split in the seat back. Always attach hook and remove slack. FAILURE TO PROPERLY USE THIS SAFETY SEAT INCREASES THE RISK OF SERIOUS INJURY OR DEATH IN A SHARP TURN, SUDDEN STOP OR CRASH. THIS RESTRAINT MUST BE USED IN CAR WITH FORWARD FACING SEATS WITH A LAP-SASH SEATBELT. THIS RESTRAINT IS NOT SUITABLE FOR USE WHERE THE ANCHORAGE STRAP MAY FALL INTO A SPLIT IN THE SEAT BACK (E.G. HATCHBACK OR WAGON). DO NOT USE THIS RESTRAINT WITHOUT THE COVER. Contact Dorel (Australia) for genuine replacement part on 1300 809 526 Seat belt extenders should not be used if the seatbelt is not long enough to secure the child restraint. TO BE USED WITH A LAP-SASH -ONLY SEATBELT IN THE FRONT/BACK OF MOST CARS WITH FORWARD FACING SEATS 4
WaRnInG WHEN USED AS A CHILD RESTRAINT (6 months to 4 years approximately) Fit the restraint firmly to the car seat. Fit the harness firmly to the child. A loose restraint or harness is dangerous. Ensure the belt webbing is not twisted. WHEN USED AS A BOOSTER SEAT (4 years TO approximately 6 TO 8 YEARS) DO NOT USE WITH JUST A LAP BELT. You must use with a lap-sash belt or with a seat belt. The lap part of the seatbelt must be firmly across the thighs and the sash straps fitted diagonally across the chest and on the shoulder. THIS BOOSTER SEAT IS NOT SUITABLE FOR USE WITH A CHILD HARNESS. WaRnInG DO NOT LEAVE CHILDREN UNATTENDED IN THE CAR. 5
WaRnInG to parents and other users DO NOT MODIFY YOUR CONVERTIBLE BOOSTER SEAT or use any accessories or parts supplied by other manufacturer s. NEVER USE CONVERTIBLE BOOSTER SEAT IF IT HAS DAMAGED OR MISSING PARTS. DO NOT use a cut, frayed or damaged vehicle seat belt. THE CONVERTIBLE BOOSTER SEAT CAN BECOME VERY HOT IF LEFT IN THE SUN. Always lightly touch the surface of any metal or plastic parts to check their temperature BEFORE putting your child in the Booster Seat. Contact with these parts can burn your child s skin. The restraint should not be purchased or sold as a second hand item. It is recommended not to use child restraints older than 10 years as the protection in an accident may be reduced ALWAYS ENSURE THAT BOOSTER SEAT HAS TETHER STRAP ATTACHED, AND THE VEHICLE S SEAT BELTS ARE USED TO SECURE THE BOOSTER SEAT TO THE VEHICLE EVEN WHEN NO CHILD IS IN THE SEAT. 6
WaRnInG ANCHORAGE FITTING INSTALLATION Read and follow all of the installation instructions for maximum protection. If you have any questions regarding the installation or use of this restraint, please contact Dorel Australia or agent, or a child restraint fitting station authorised by the relevant transport authority, or in New Zealand, to consult the agent for the vehicle. Do not modify or alter this restraint in any way. Use only Dorel Australia recommended parts and accessories. Protect all webbing from possible damage by sharp edges and corners. Check your vehicle owner s handbook for the location of correct anchorage points and possible need for spacers. If a suitable anchorage point cannot be found, contact a child restraint fitting station for recommendations about your vehicle. Some vehicles may have anchor points which are recessed below the vehicle trim, spacers are supplied to raise the anchor point if required. An extension strap may be needed for vehicles without a fixed parcel shelf. Extension straps and extra fittings are available from various stores. Note : Extension straps 300mm ref no. 014398, 600mm ref no. 014399 and an anchor bolt kit, ref no. 014400. Seat belt extenders should not be used if the seat belt is not long enough to secure the child. 7
IMPORTANT Child restraints must be used correctly to provide proper protection for your child. The new type of clip anchorage system on child restraint must be used in the correct way. Be especially careful to use the clip in the following way. RIGHT Make sure there is no slack in the top strap and the attachment clip is upright in the anchorage fitting. WRONG The clip must not lie flat on the anchorage fitting. FLOOR MOUNTED ANCHORAGES ANCHORAGES IN VERTICAL PANEL AT REAR OF VEHICLE 8
ANCHORAGE FITTING INSTALLATION (continue) If the car is fitted with a child restraint anchorage point. Locate the anchorage points behind the rear seating position (consult the car owner s handbook for the location of the anchorage point). Remove the thread plug from the parcel shelf / floor/ roof and install the attachment bolt as shown in Fig 1. WaRnInG CAUTION: DO NOT OVERTIGHTEN THE ATTACHMENT BOLT. MAXIMUM TORQUE 20 Newton Metre. Attachment Bolt Lock Washer Anchor Fitting Spacers (if required) Vehicle Trim Front of vehicle Fig 1 Vehicle Metal Structure If the car is not fitted with a child restraint anchorage point. For sedans only Drill a 9mm diameter hole in the parcel shelf on the centre line of the seating position as shown in Fig 2 (page 10). Install the anchor bolt as shown in Fig 3 (page 10). For vehicles other than sedans In Australia, consult your nearest child restraint fitting station or traffic authority for vehicle inspection to find the best, correct position for the placement of anchorage point, and for the correct attachment bolt length and use of spacers. In New Zealand, consult the agent for the vehicle. WaRnInG CHILD RESTRAINTS MUST NOT BE ATTACHED TO UNSOUND METAL OR TO WOOD OR SYNTHETIC STRUCTURES. WHEN DRILLING THE 9MM HOLE DO NOT DRILL THROUGH FUEL LINES, FUEL TANKS, ELECTRICAL WIRING, OR RADIO SPEAKERS. WEBBING STRAPS MUST BE PROTECTED FROM SHARP CORNERS AND EDGES. THE ANCHOR FITTINGS MUST BE USED ONLY AS DESCRIBED ABOVE. IT MUST NOT BE HOOKED ONTO ANY OTHER OBJECT. 9
Centre-line of seating position Attachment bolt Front of vehicle fig 2 Spacers (if required) Vehicle Trim Reinforcing Washer fig 3 Front of vehicle Anchor Fitting Vehicle Metal Structure Lock Washer Securing Nut WaRnInG VEHICLE SEAT LOCATION IMPROPER PLACEMENT OF THE SAFETY SEAT INCREASES THE RISK OF SERIOUS INJURY OR DEATH. Some seating positions in your vehicle may NOT be safe for this safety seat. Some vehicles do not have any seating positions that can be used safely with the seat. If you are not sure where to place the Booster Seat in your vehicle, consult your vehicle s owner s handbook. 10
CORRECT VEHICLE POSITION CoRReCT Use CoRReCT Use InCoRReCT Use 11
TETHER STRAP AND HEADREST ADJUSTMENT Button Adjust anchorage strap and remove slack. Pull loose end of strap to tighten. Press on the adjuster button with thumb and pull strap back through to loosen anchorage strap using strap which is attached to the seat. GENERAL INSTRUCTIONS TOP ANCHORAGE STRAP To attach the anchorage strap, Place one knee in the child seat and push down firmly then attach hook to anchor in vehicle. anchor hook Vehicle anchor kit ADJUSTING THE HEADREST HEIGHT The Seat is fitted with headrest Height Adjustment Lock which is RED in colour. Pushing it in unlocks the headrest to move it up or down into the desired height position. 5 Height positions are available. 12
RECLINING BACKREST TO RECLINE BACKREST Push the backrest of the seat to recline it backward for greater comfort if needed. FOR UPRIGHT POSITION Pull the backrest of the seat forward in the upright position. GENERAL INSTRUCTIONS 13
FEATURES - TODDLER RESTRAINT WITH 6 POINT HARNESS FRONT VIEW TODDLER RESTRAINT WITH BUILT IN HARNESS 6 7 8 9 10 1. Forward Facing Belt Path Indicators (Yellow) 2. Belt Mates (If Fitted) 3. Quick Release Buckle 4. Centre Front Adjuster Lever 5. Harness Adjuster Strap *opening slit in trim 1 2 3 4 5 6. Air Protect (If Fitted) 7. Harness Slot 8. Armrest/Cover (If Fitted) 9. Insert (If Fitted) To be used from 6 months to approximately 1 year) 10. Cup Holder (Both Sides) 14
FEATURES - toddler RESTRAINT WITH 6 POINT HARNESS BACK VIEW 11 17 12 13 18 14 19 15 16 Trim style and design may vary. 11. Headrest/Trim 16. Pocket (Instruction Manual) 12. Adjustable Headrest 17. Booster Seat Belt Path Button (5 Positions) Indicators (Red) 13. Tether Strap 18. Adjuster (Tether Strap) 14. Hook 19. Anchorage Fitting 15. Splitter Plate Toddler restraint with built in harness 15
toddler shoulder height marker Toddler restraint with built in harness LABEL 3 LABEL 2 LABEL 1 shoulders MUsT be above THIs line CHanGe To booster MoDe WHen shoulders ReaCH THIs line LABEL 1 LABEL 2 To be used in forward-facing position by children whose shoulders are above the lower shoulder height marker LABEL 1 (approximately 6 months of age) until their shoulders reach the middle shoulder height marker LABEL 2 (approximately 4 years of age). Then convert the child restraint to booster mode and use a lap sash belt only. See page 22 to 26. 16
toddler RESTRAINT INSTALLATION USING LAP-SASH ONLY The shoulder straps must be in the slots which are nearest to the child s shoulders, but not more than 25 mm below the child s shoulders. To be used with a lap sash belt only. NOTE: If the baby s neck muscles are unable to support their head, then the child should remain in a rear facing seat. Toddler restraint with built in harness 17
PREPARING SEAT TO FIT YOUR CHILD You MUST make these adjustments with your child before you install the child restraint in the vehicle. Please adjust harness according to the infants shoulder height prior to installation. Toddler restraint with built in harness 2 4 1 5 SPLITTER PLATE 3 TO ADJUST SHOULDER STRAP HEIGHT: 1. Press the harness release lever at the front of seat. 2. Pull both shoulder straps simultaneously to lossen. 3. Undo the straps from the splitter plate on the back of the child restraint. Re-thread the shoulder straps through the desired slots. Reconnect the straps to the splitter plate. 4. Press red button to release buckle assembly for ease of child fitment. Place child in seat. To tighten: 5. Fasten buckle assembly (See Page 19). Pull the adjuster belt at the front of the seat until the harness belt lies firmly against the child. 18
PREPARING SEAT TO FIT YOUR CHILD step 1 step 2 step 3 Step 1 : Insert one buckle tongue as shown above. Step 2 : Insert the second buckle tongue as illustrated above. Listen for a CLICK. Step 3 : Remember to always pull up on the harness straps to make sure buckle is locked properly. WaRnInG DO NOT USE SHOULDER STRAPS OF UNEQUAL HEIGHTS. Toddler restraint with built in harness CORRECT USE INCORRECT USE Ensure the harness is attached to the splitter plate. Ensure the harness is pulled through the plastic mould & trim all the way and correctly tensioned. Ensure harness straps and adjuster strap is not twisted. 19
toddler USE INSTALLATION Toddler restraint with built in harness 2 1 4 FORWARD FACING SEAT INSTALLATION: 1. Thread the vehicle lap-sash belt through the yellow belt path indicators. 2. Position the lap part around the armrest as illustrated. 3. Thread the lap-sash belt between the seat back and trim. Thread the lap sash belt through the opening. Refer to illustration. 4. Position the lap sash belt around the armrest and lock the car buckle. Listen for CLICK and gently pull to ensure buckle is locked. NOTE: Ensure that the tether strap is attached at all times. Refer to page 12 for fitment. Place one knee on the child restraint and push down firmly while pulling up on belt to tighten. Ensure all slack is taken out. With weakest hand, tilt and push the child restraint forward and back, and from side to side. If the seat belt does not loosen, your child seat should be secure. If not : Change seat position. 3 20
CHILD shoulder height marker LABEL LABEL LABEL CHanGe To booster MoDe WHen shoulders ReaCH THIs line shoulders MUsT be below THIs line LABEL 2 LABEL 3 CHILD USE AS A BOOSTER SEAT To be used as a booster mode when the child shoulders are above the middle height marker LABEL 2 until their shoulders reach the upper height marker LABEL 3 (approximately 6 to 8 years). Then the child needs to be moved into the next form of restraint when they reach the top shoulder height marker. See page 27 21
FEATURES - CHILD BOOSTER SEAT FRONT VIEW 1 CHILD USE AS A BOOSTER SEAT 5 6 7 8 *opening slit in trim 2 3 4 1. Headrest/Trim 2. Car Lap-Sash Belt 3. Storage for buckle 4. Storage for Harness Adjuster Strap 5. Air Protect (If Fitted) 6. Seat Trim 7. Booster SeatBelt Path Indicators (Both Sides) 8. Cup Holder (Both Sides) 22
FEATURES - CHILD BOOSTER SEAT BACK VIEW 13 14 15 16 12 Trim style and design may vary. 9 10 *Thread the straps for storage 11 CHILD USE AS A BOOSTER SEAT 9. Adjustable Headrest Button (5 position) 10. Tether Strap 11. Hook 12. Shoulder Straps Storage 13. Booster SeatBelt Path 14. Adjuster (Tether Strap) 15. Pocket (Storage for Instruction manual) 16. Anchorage Fitting Indicators (red) 23
REMOVE HARNESS SYSTEM SPLITTER PLATE Undo the straps from the splitter plate on the back of the child restraint. Pull harness adjuster strap forward to the maximum. See feature (6) on page 14. CHILD USE AS A BOOSTER SEAT Roll the harness adjuster strap and store in the opening area under trim. See feature (4) on page 22. Press red button to release buckle assembly. Insert buckle in the opening area on the seat covered under the flap. See feature (3) on page 22. Remove both shoulder straps from the harness slots, See feature (8) on page 14. Thread the shoulder straps through the opening between the armrest and side of the seat, refer to illustration on page 23. Store the straps and (belt mates if fitted) in the opening area at the back on the seat, refer to feature (11) on page 23. 24
BOOSTER SEAT INSTALLATION USING LAP-SASH ONLY Securing Your Child In Vehicle Place the Booster Seat firmly against the back of a forward facing vehicle seat equipped with lap-sash belt. DO NOT place the Booster Seat in a vehicle without the tether strap attached to the vehicle s anchor fitting. Refer to page 12. Have your child sit in the safety seat with their back flat against its back. Position the sash belt through the shoulder belt guide in the headrest. The lap belt portion MUST be positioned low on the hips, Fasten buckle and pull up on shoulder belt to tighten. The vehicle s seat belts MUST NOT be twisted. CHILD USE AS A BOOSTER SEAT CORRECT INCORRECT INCORRECT WaRnInG A sash belt under the arm or behind the back is dangerous 25
BOOSTER SEAT INSTALLATION USING LAP-SASH ONLY Correct Shoulder Position CHILD USE AS A BOOSTER SEAT To ensure the correct head support is obtained, the bottom of the headrest MUST be even or slightly higher with the top of child s shoulders as illustrated. NOTE : If the vehicle seat belt lays across child s neck or face, then readjust the headrest height. CAUTION! In the event of a crash, a seat belt across the child s throat could cause a strangulation hazard. ACCESSORIES Using Cup Holders To use cup holders, simply rotate outward. To close cup holders, rotate inwards to close. Rotate 26
THE NEXT SEAT FOR YOUR CHILD LABEL 3 HEADREST AT HIGHEST POSITION shoulders MUsT be below THIs line The booster seat is unsuitable for the occupant when the shoulders are above the upper marker (LABEL 3). The child needs to be moved into the next form of child restraint (a bigger booster seat or a child harness) when they reach the top shoulder height marker. GENERAL INSTRUCTIONS NOTE: This illustration is representative only. Design and style may vary. CHILD HARNESS From 7 to 10 years of age BOOSTER SEAT Approx 4 to 10 years of age 27
CARE AND MAINTENANCE NOTE: Remove harness as described on page 24. Headrest cover: Adjust the booster seat headrest to its highest position. Separate velcro at the back of the headrest and remove cover. GENERAL INSTRUCTIONS Main body cover: Separate velcro at the back of the seat. Pull off the elastics around the armrest and remove cover off the seat. The seat covers can be machine washed in lukewarm water on the Delicate cycle. Tumble dry for 10-15 minutes on low heat. DO NOT BLEACH DO NOT DRY CLEAN DO NOT IRON Style and design may vary for the trim. Elastic Strap 28
CARE AND MAINTENANCE VELCRO The insert is to be used from 6 months to approximately 1 year) To Remove insert To remove the insert, separate the velcro 2 places. Refer to illustration above. Undo the buckle and pull the insert out. To replace insert Feed the crotch part of the buckle through the opening slot in the insert. Place the shoulder straps as illustrated and attach velcro 2 places. Fasten buckle assembly. Fitting the headrest cover Extend the booster seat headrest to its highest position then GENERAL INSTRUCTIONS headrest. Fitting the main body cover Starting at the shoulders, place the trim on and fasten the velcro at the back. Next, on each side of the trim you will see elastics, these elastics need to be threaded around the armrest and attached. Last step, pull cover over base. 29
VERY IMPORTANT: Only use this child restraint with the cover supplied or a manufacturer-authorized replacement cover with identical shoulder height markers. GENERAL INSTRUCTIONS CARE AND MAINTENANCE CLEANING METAL AND PLASTIC PARTS - Sponge clean with mild soap and cool water. NEVER clean with ammonia or bleach based, or spirit-type cleaners. DO NOT USE THIS SAFETY SEAT WITHOUT ITS COVER FROM TIME TO TIME CHECK THE SEAT for worn parts, torn material and stitching. If damage is found, DO NOT try to modify the safety seat. Replace the safety seat. IMPORTANT - Only genuine replacement parts supplied by Dorel Australia Pty Ltd can be used on the Convertible Booster Seat. 30
Follow the manufacturer s instructions at all times. Before removal, ensure you have carefully noted the way which the various parts are attached to the seat so as to facilitate reassembly. Your child car seat is equipped with a buckle designed to give your child maximum protection during proper use. When working properly, your buckle should always fasten with an audible click. If sticky liquids such as baby food, fruit juice, etc, get into the buckle it may become sluggish and you will not hear a click. The buckle should be cleaned by following the steps below. Place the buckle unit under running water (40 degrees Celsius) Let the water flow through the mouth of the buckle for one minute. Simultaneously latch and unlatch the tongues into the buckle several times until a strong audible click is heard. If you still cannot hear a strong audible click after latching the buckle several times, then repeat the process again. DO NOT oil any part of the buckle and allow buckle to dry. GENERAL INSTRUCTIONS IMPORTANT - Only genuine replacement parts supplied by IGC Dorel Pty Ltd can be used on the Convertible Booster Seat. 31
WARRANTY DOREL AUSTRALIA PTY LTD WARRANTS YOUR NEW PRODUCT TO BE FREE FROM DEFECTS IN MATERIALS AND WORKMANSHIP FOR 6 YEARS ON THE SEAT & 2 YEARS ON THE TRIM, FROM THE DATE OF PURCHASE, PROVIDED THAT THE PRODUCT IS USED IN ACCORDANCE WITH ACCOMPANYING RECOMMENDATIONS OR INSTRUCTIONS WHERE PROVIDED. THE BENEFIT OF THIS WARRANTY IS IN ADDITION TO YOUR RIGHTS UNDER THE AUSTRALIAN CONSUMER LAW AND TO OTHER RIGHTS AND RE MEDIES OF THE CONSUMER UNDER A LAW IN RELATION TO THE GOODS OR SERVICES TO WHICH THE WARRANTY RELATES. DOREL AUSTRALIA PTY LTD WILL PROVIDE YOU WITH YOUR CHOICE OF A REFUND, REPAIR OR EXCHANGE (WHERE POSSIBLE) FOR THIS PRODUCT IF IT BECOMES DEFECTIVE WITHIN THE WARRANTY PERIOD. DOREL AUSTRALIA PTY LTD WILL BEAR THE REASONABLE EXPENSE OF CLAIMING THE WARRANTY. THIS WARRANTY WILL NO LONGER APPLY WHERE THE DEFECT IS A RESULT OF ALTERATION, ACCIDENT, MISUSE, ABUSE OR NEGLECT. PLEASE RETAIN YOUR RECEIPT AS PROOF OF PURCHASE AND CONTACT OUR CUSTOMER SERVICE CENTRE ON PH: 1300 809 526 OR ALTERNATIVELY, VIA OUR WEBSITE AT WWW.DOREL.COM.AU FOR ANY DIFFICULTIES WITH YOUR PRODUCT. WARRANTY CLAIMS AND CLAIMS FOR EXPENSE INCURRED IN RETURNING THIS PRODUCT CAN BE ADDRESSED TO OUR CUSTOMER SERVICE CENTRE AT 655-685 SOMERVILLE ROAD, WEST SUNSHINE VIC 3020. FOR NEW ZEALAND PLEASE CONTACT CUSTOMER SERVICE CENTRE, 14 SIR WILLIAM AVENUE, EAST TAMAKI, AUCKLAND, 2013. AUCKLAND: (09) 274 1040 NZ WIDE: 0800 628 000 (TOLL FREE). HOURS: 8:00 AM - 4:00 PM, MONDAY TO FRIDAY. OUR GOODS COME WITH GUARANTEES THAT CANNOT BE EXCLUDED UNDER THE AUSTRALIAN CONSUMER LAW. YOU ARE ENTITLED TO A REPLACEMENT OR REFUND FOR A MAJOR FAILURE AND COMPENSATION FOR ANY OTHER REASONABLY FORESEEABLE LOSS OR DAMAGE. YOU ARE ALSO ENTITLED TO HAVE THE GOODS REPAIRED OR REPLACED IF THE GOODS FAIL TO BE OF ACCEPTABLE QUALITY AND THE FAILURE DOES NOT AMOUNT TO A MAJOR FAILURE. Australian Standard AS/NZS 1754 Lic 40071 SAI Global IMPORTANT: KEEP THIS BOOKLET IN THE POCKET PROVIDED AT THE REAR OF THE CHILD RESTRAINT REF # 014914 11/13