over headline over headline 3Style onnectors
annon 3Style Series,, onnectors TT annon connectors set the industry standard for performance and reliability in the most demanding conditions and harshest environments. Our 3Style Series,, onnectors are designed to withstand the extreme shock, exposure and vibration that are commonplace in Defense and ommercial erospace applications. We offer lightweight, spacesaving solutions to our military customers, coupled with high bandwidth and high power for severe service application needs. ore than a century of experience, coupled with unparalleled engineering and testing resources, has established TT annon as one of the premier providers of interconnect solutions worldwide. With a proven track record for engineering and manufacturing excellence, TT annon continues to deliver a broad range of innovative products and solutions that enable our customers to meet their most demanding design requirements, where impeccable reliability and safety are essential. xample pplication reas Defense ilitary aircraft ilitary communication systems Hand held and vehicle platforms ilitary ground support systems ilitary computer systems Harsh environment platforms lind mate applications High density, low signal platforms Hand held and vehicle platforms Unmanned systems erospace ircraft engines General electric testing equipment ommercial business aviation erospace launch vehicles
3Style onnectors: recision ngineered, Lightweight & Rugged TT annon s 3Style Series,, onnectors are designed to tackle the most extreme conditions with exceptional versatility in the harshest environments. Small, lightweight and highly reliable, our D3 Style connectors deliver consistency and performance when it matters most. D3Style Series (KJL) TT annon KJL 3Style Series connectors offer highdensity contact arrangements in a lightweight miniature circular connector. TT annon KJL series connectors are an industry standard for military and aerospace applications. The environmentally sealed KJL series features quickmating, threepoint bayonet coupling and operates across a wide temperature range. D3Style Series (KJ) TT annon KJ 3Style Series are a weightreduced and low profile circular connector ideally suited for avionic applications where space and weight are prime considerations. t offers highdensity contact arrangements in a lightweight miniature circular connector. TT annon KJ series connectors feature a quickmating, threepoint bayonet coupling, are environmentallysealed and operate across a wide temperature range. TT annon KJ series mil spec connectors were originally designed for military vehicles and are now industry standard aerospace and military connectors. 3Style Series (KJ) The defacto standard circular connector for use in harsh military and aerospace environments, TT annon's KJ 3Style Series onnectors offer highdensity contact arrangements in a lightweight miniature circular connector. TT annon's KJ series connectors have quickmating, triplelead threaded, selflocking coupling, are environmentallysealed and operate across a wide temperature range. These connectors were originally designed for military vehicles and are now use for multiple applications throughout the erospace & Defense ndustry. 3Style Series omposite (KJ) lightweight standard circular connector for use in military and aerospace environments with significant weight savings over aluminiumbodied D3Style. High density layouts with up to data connections and power contacts rated up to. eatures a triplestart coupling with antidecoupling ratchet for high vibration applications, admium and lectroless ickel platings, 0 percent scoopproof contacts and rated to 00 mating cycles.
Table of ontents Specifications and Test Data...35 3Style Series...6 3StyleSeries... 3Style Series...1 3Style Series omposite... olarizing ositions...... ontact rrangements... ontacts...27 Torque Values / Wire Dimensions...2 ackshells...231 Tools...32 ssembly nstructions...33 Specifications...34 roduct Safety and Warranty...35 bout TT annon...36 n addition to our 3style series, we also offer these connectivity solutions: ombo DSub roduct offering includes ability to integrate signal and coax, high power, and high voltage. ayonet Signal and power connectors with exceptional sealing against the ingress of fluids and will withstand the effects of high vibrations. icrominiature High performance and reliability with exceptional versatility. vailable in rectangular, circular and strip configurations, many of our connectors are designed to be comparable to the LDTL35 specification. 2
3Style Series,, onnectors* SRS SRS SRS GROUDG GRS (Standard on Series connector) SHLL HRDWR is aluminum alloy SULTOR TO SHLL SL LOSD TRY SOKT OTT DSG HGH STRGTH ULTLT TL RTG L assures positive retention with inwardly deflected tines that lock securely behind contact shoulder SL, STROGR OTTS are designed to resist bending and are crimp terminated OOLO SRT WR SLG GROT HGH STRGTH ULTLT TL RTG L assures positive retention with inwardly deflected tines that lock securely behind contact shoulder SULTOR TO SHLL SL WR SLG GROTS WR SLG GROTS SL, STROGR OTTS are designed to resist bending and are RHRL SLG GSKT crimp terminated RHRL SLG GSKT LOSD TRY SOKT OTT TRL SL RHRL SL around the connector interface is designed to minimize compression set when connectors are mated DSG SLR, STROGR OTTS are designed to resist bending and are crimp terminated RSLT TRL SLS feature individual raised seal barriers around each pin contact HGH STRGTH ULTLT TL RTG L assures positive retentin with inwardly deflected tines that lock securely behind contact shoulder TRL SL GROUDG GRS orrosion and zinc resistant shells of aluminum alloy with cadmium and zinc over nickel plating withstand a 500 hour salt spray exposure Rear release crimp snapin contacts High contact density Standard L302 contacts, L6 application tools and LSTD 60 insert arrangements Special/custom capabilities 0% scoopproof Series and Light weight /Low rofile Series Operates under severe high temperature vibration testing through 0 engineered for high density circuitry Series nterfacial seal helps prevent electrolytic erosion of contacts Series Superior shielding provides outstanding protection up to 65d at GHZ. Series Specification omparison Design riteria Series Series Series (luminum) Series (omposite) Low rofile/light Weight no yes no yes Scoop roof yes no yes yes oupling System ayonet ayonet Triple Start Thread Triple Start Thread lectrolytic rosion no no yes yes Durability (ycles) 500 0 500 00 High mpact Shock yes no yes yes xternal ending oment 650 in/lbs 0 in/lbs 00 in/lbs 00 in/lbs Random Vibration "J" 4.5G, mbient 43.7G, mbient 4.5G, mbient 4.5G, mbient Sine Vibration 60G 60G 60G Sand, Dust, ce yes yes yes ontact Rating ontact D ** ** Test urrent D Test mperage 5 3 5 7.5 aximum illivolt Drop* 40 30 40 35 rimp Well Data Well Well Diameter Depth.0345 ±.00.7/.1.020 ±.00.7/.1.0365 ±.00.7/.1.0470 ±.00./..0670 ±.00./..00 ±.00./. * aximum millivolt drop data is determined by measuring resistance of mated contacts from end to en ** or reference only *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent. 3
3Style Series,, onnectors* erformance and aterial Specifications *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent. TRLS D SHS luminum Receptacle Grounded lug luminum alloy luminum alloy* nsulator High grade plastic High grade plastic ontacts opper alloy, gold plate opper alloy, gold plate Grommet and Seal Silicone base elastomer Silicone base elastomer Jam ut luminum alloy Grounding Spring eryllium copper *inish as noted in How To Order sections. omposite Receptacle Grounded lug Thermoplastic Thermoplastic High grade plastic High grade plastic opper alloy, gold plate opper alloy, gold plate Silicone base elastomer Silicone base elastomer eryllium copper LTRL DT ontact : D, *, *,, and ontact Rating and Wire ccomodation ontact and Test mps Wire D * * 2 26 1 1.5 2.0 3.0 5.0 1.5 2.0 3.0 2.0 3.0 5.0 3.0 5.0 7.5 7.5.0.0.0.0 *or reference only Service Rating Service Rating ltitude ated Unmated Sea Level 00 00 50,000 ft. 00 550 70,000 ft. 00 350 0,000 ft. 00 0 Service Rating ated Unmated 00 00 600 400 600 260 600 0 Test voltage, (rms), work voltage to be determined by application Service Rating ated Unmated 0 0 00 600 00 400 00 0 Service Rating ated Unmated 00 00 00 00 00 500 00 0 Test Data Test Description Durability Temperature Range Vibration Shielding ffectiveness orrosion Resistant luid mmersion High mpact Shock ltitude Other nvironments arameters 500 cycles of mating and unmating, 0 cycles for Series with spring fingers lass, ; 65º (5º) to + 0º (+32º) lass ; 65º (5º) to + 0º (+302º) lass,w: 65º (5º) to + 5º (+347º) ated connectors are vibrated with weights to simulate rear accessory loads to the following levels: Sine Vibration: Up to 60 G's Series & (at rated temperature Series ) ot applicable for Series. Random Vibration: 43.7 Grms at rated temperature Series 4.5 Grms at mbient Temperature Series & 43.7 Grms at mbient Temperature Series lass : leakage attenuation, greater than 0d at 0hz, greater than 65d at GHz. to shell conductivity, 1.0 millivolt max. resistance. lass W: leakage attenuation, greater than 0d at 0 Hz, greater than 50d at GHz. to shell conductivity, 2.5 millivolt max. lass, W, and Z will withstand 500 hours salt spray. lass,,, will withstand 4 hours salt spray. onnectors are fluid resistant to many fuels, solvents, coolants and oils. ated conectors terminated with L cable and environmentally sealed backshells will withstand high impact shock per LS01. pplicable to Series & only. Designed to operate between sea level and 0,000 ft. above sea level. ated connectors shall withstand sand and dust per method 0 of LSTD2 and be ice resistant. pplicable to Series & only. OT: or hermetic standard or test data please consult TT. *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent. 4
3Style Series,, onnectors* nsert vailability and dentification DSLR:Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent. Series 35 5 35 3 4 35 5 1 35 7 6 26 35 1 12 130 132 135 35 3 41 23 25 4 2 35 61 Series & 35 4 5 4 35 5 1 35 7 6 26 35 2 30 32 35 35 3 41 75 32 35 53 55 4 2 35 37 43 46 42 61 64 66 Service Rating, Twinax Twinax, oax, Twinax, oax Total ontact ontacts D 6 6 3 4 5 6 7 3 4 5 1 37 6 26 55 2 30 32 66 7 3 41 4 32 0 53 55 56 2 37 43 46 30 42 61 64 66 37 55 66 7 0 40 53 3 4 5 6 7 1 26 26 2 32 37 41 32 53 55 4 40 3 61 2 3 4 5 1 4 2 2 1 2 2 37 4 6 4** 6 4*** 2*** *** 3*** 4* * oax for RG cables ** oax for RG4,, or 3 cables *** Twinax for /600002 cables (check factory for other cable applications) *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent. 5
3Style Series onnectors* How To Order ilitary omenclature DSLR:Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent. S UR SHLL STYL LSS SHLL SZ HRDWR SH OTT RRGT OTT STYL S27467Style T 35 S S UR SHLL STYL S27466 Wall ounting Receptacle S2746 Jam ut Receptacle S27467 Grounded lug S27656 Wall ounting Receptacle (back panel mounting) S27505 ox ounting Receptacle (back panel) (lass ) LSS nactive for new design. Superseded by lass T. G nvironmental resistant Space Grade nvironment resistant with straight potting cup accessories T nvironment resistant with accessory threads and teeth, except S27505 (without rear accessory) (lass T not applicable to S27505) OLRZG OSTO SHLL SZ,,,,,,,, and HRDWR SH STDRD right cadmium over electroless nickel plate, 5º to +302º (65º to +0º) Olive drab cadmium over electroless nickel plate, 5º to +347º (65º to +5º) lectroless nickel, 5º to +32º (65º to +0º) OTT RRGT See pages and. OTT STYL in S Socket * Less in ontact * Less Socket ontact *Used only when other than power contacts are to be installed (i.e. shielded, thermocouple, etc.) OLRZG OSTO,,, and D. (o letters required for normal). See page. ote: To order S connectors less standard power contacts, purchase order must state Less ontacts annon omenclature SRS RX KJL Series Scoop proof SHLL STYL 0 Wall mounting receptacle 3 Wall mounting receptacle (back panel mounting) 4 Thru bulkhead receptacle* 5 ox mounting receptacle (back panel mounting) 6 Straight plug, grounded 7 Jam nut receptacle LSS nactive for new design. Superseded by lass T. G nvironmental resistant Space Grade nvironment resistant with strain relief accessory nvironment resistant with straight potting cup accessory T nvironment resistant (without rear accessory) (lass T not applicable to KJL5) *onsult factory for availability SRS RX SHLL STYL LSS SHLL SZ HRDWR SH OTT RRGT OTT STYL OLRZG OSTO ODTO OD SHLL SZ,,,,,,, and HRDWR SH STDRD right cadmium over electroless nickel plate, 5º to +302º (65º to +0º) Olive drab cadmium over electroless nickel plate, 5º to +347º (65º to + 5º) lectroless nickel, 5º to +32º (65º to +0º) Z Zinc ickel, lack (Dash) When using a finish modification code OTT RRGT See pages and. KJL 6 T 35 S OTT STYL in S Socket S insocket ( style 4 only) OLRZG OSTO (normal),,,, D. See page. ODTO OD L Less contacts, not stamped on connector Outgassed S space graded connector linch uts installed 440, 632 ) 27 Outgassed, standard connector 26 lack Zinc obalt, RoHS ompliant *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent. 6
3Style Series onnectors* Wall ounting Receptacle S27466Style (S service class,, T) KJL0 J D. X. OLRZG KYWY 1.0 (31.50) X. L H T THRD D. LU D (DTS RR RLS OTT RTTO SYST) OT: or backshell dimensions and configurations, see pages 2 and 31. Overall Length With ackshells Dia. ax..573 (.55).701 (.1).51 (.62).76 (.7) 1.1 (27.7) 1. (30.6) 1.333 (33.6) 1.45 (37.03) 1.53 (40.) H ax..0 (2.54).0 (2.54).0 (2.54).0 (2.54).0 (2.54).0 (2.54).0 (3.30).0 (3.30).0 (3.30) J Dia. ax..662 (.1). (.57).60 (.3) 1.05 (27.56) 1.0 (30.73) 1.3 (33.45) 1.442 (36.63) 1.567 (3.0) 1.62 (42.) L ax..632 (.05).632 (.05).632 (.05).632 (.05).632 (.05).632 (.05).602 (.2).602 (.2).602 (.2) ax..5 (.33) 1.051 (26.70) 1.5 (2.0) 1. (31.47) 1.332 (33.3) 1.45 (37.03) 1.52 (40.1) 1.70 (43.3) 1.32 (46.53) T...7 (1.26). (.62).06 (.01).6 (.61) 1.062 (26.7) 1.6 (2.36) 1.0 (31.75) 1.375 (34.3) 1.500 (3.) Dia. ax.. (3.51) (3.51). (3.51). (3.51). (3.51). (3.51). (3.51).7 (3.).7 (3.) T Thread 7/2U2 /U2 /U2 /U2 /U2 /1U2 /1U2 /1U2 /1U2 able lamp 1.46 (46.) 1.46 (46.) 1.46 (46.) 1.46 (46.) 1.66 (4.4) 1.66 (50.70) 1.66 (50.70) 1.66 (50.70) 1.66 (50.70) otting ax. 1.451 (36.6) 1.451 (36.6) 1.451 (36.6) 1.451 (36.6) 1.451 (36.6) 1.451 (36.6) 1.451 (36.6) 1.451 (36.6) 1.451 (36.6) Wall ounting Receptacle (ack anel) S27656Style (S service class,, T) KJL3 J D. X. OLRZG KYWY 1.7 (31.67) X. L H T THRD D. LU D (DTS RR RLS OTT RTTO SYST) X. L THKSS (including mounting hardware) OT: or backshell dimensions and configurations, see pages 2 and 31. Dia. ax..573 (.55).701 (.1).51 (.62).76 (.7) 1.1 (27.7) 1. (30.6) 1.333 (33.6) 1.45 (37.03) 1.53 (40.) ax..4 (5.4).4 (5.4).4 (5.4).4 (5.4).4 (5.4).4 (5.4).4 (5.1).4 (5.1).3 (4.0) H ax..0 (2.54).0 (2.54).0 (2.54).0 (2.54).0 (2.54).0 (2.54).0 (3.30).0 (3.30).0 (3.30) J Dia. ax..662 (.1). (.57).60 (.3) 1.05 (27.56) 1.0 (30.73) 1.3 (33.45) 1.442 (36.63) 1.567 (3.0) 1.62 (42.) L ax.. (.3). (.3). (.3). (.3). (.3). (.3).70 (.07).70 (.07).70 (.07) ax..5 (.33) 1.051 (26.70) 1.5 (2.0) 1. (31.47) 1.332 (33.3) 1.45 (37.03) 1.52 (40.1) 1.70 (43.3) 1.32 (46.53) T...7 (1.26). (.62).06 (.01).6 (.61) 1.062 (26.7) 1.6 (2.36) 1.0 (31.75) 1.375 (34.3) 1.500 (3.) Dia. ax.. (3.51) (3.51). (3.51). (3.51). (3.51). (3.51). (3.51).7 (3.).7 (3.) T Thread 7/2U2 /U2 /U2 /U2 /U2 /1U2 /1U2 /1U2 /1U2 Overall Length With ackshells able lamp 1.05 (45.5) 1.05 (45.5) 1.05 (45.5) 1.05 (45.5) 1.35 (4.0) 1.55 (4.66) 1.55 (4.66) 1.55 (4.66) 1.55 (4.66) otting ax. 1.4 (35.1) 1.4 (35.1) 1.4 (35.1) 1.4 (35.1) 1.4 (35.1) 1.4 (35.1) 1.4 (35.1) 1.4 (35.1) 1.4 (35.1) erformance Specificationsages 3 and 4. ontacts, Sealing lugs, ssembly Tools ages, 31, and 32. ontact rrangements ages and. *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent. 7
3Style Series onnectors* ox ounting Receptacle (ack anel) S27505Style (S service class ) KJL5 H L K X. J D. X. OLRZG KYWY.060 (1.52) X. GROT D. LU D (DTS RR RLS OTT RTTO SYST) X. L THKSS (LUDG OUTG HRDWR) OT: This connector does not accommodate backshells. Dia. ax..573 (.55) ax..4 (5.4) H ax..0 (2.54) J Dia. ax..662 (.1) K ax.. (5.56) L ax.. (.3) ax..5 (.33) T...7 (1.26) Dia. ax.. (3.51).701 (.1).4 (5.4).0 (2.54). (.57). (5.56). (.3) 1.051 (26.70). (.62) (3.51).51 (.62).4 (5.4).0 (2.54).60 (.3). (5.56). (.3) 1.5 (2.0).06 (.01). (3.51).76 (.7).4 (5.4).0 (2.54) 1.05 (27.56). (5.56). (.3) 1. (31.47).6 (.61). (3.51) 1.1 (27.7).4 (5.4).0 (2.54) 1.0 (30.73). (5.56). (.3) 1.332 (33.3) 1.062 (26.7). (3.51) 1. (30.6).4 (5.4).0 (2.54) 1.3 (33.45). (5.56). (.3) 1.45 (37.03) 1.6 (2.36). (3.51) 1.333 (33.6).4 (5.1).0 (3.30) 1.442 (36.63).0 (6.35).70 (.07) 1.52 (40.1) 1.0 (31.75). (3.51) 1.45 (37.03).4 (5.1).0 (3.30) 1.567 (3.0).0 (6.35).70 (.07) 1.70 (43.3) 1.375 (34.3).7 (3.) 1.53 (40.).3 (4.0).0 (3.30) 1.62 (42.).0 (6.35).70 (.07) 1.32 (46.53) 1.500 (3.).7 (3.) Straight lug Grounded S2746Style (S service class,, T) KJL6 J D. OLRZG KYWY L T THRD D. G D. X. LU D (DTS RR RLS OTT RTTO SYST) OT: or backshell dimensions and configurations, see pages 2 and 31. ax. G Dia. ax. J Dia. ax. (lass T) L ax. T Thread Overall Length With ackshells able lamp otting ax..55 (.6).5 (.2).43 (.27) 1.4 (31.34) 7/2U2 1.73 (45.54) 1.671 (42.44).7 (1.).4 (.).6 (.52) 1.4 (31.34) /U2 1.73 (45.54) 1.671 (42.44).66 (.00) 1.6 (2.36).760 (.30) 1.4 (31.34) /U2 1.73 (45.54) 1.671 (42.44).0 (.) 1.21 (32.54).5 (.4) 1.4 (31.34) /U2 1.73 (45.54) 1.671 (42.44) 1.5 (2.32) 1.406 (35.71) 1.0 (.65) 1.4 (31.34) /U2 1. (4.5) 1.671 (42.44) 1.2 (31.04) 1.5 (3.51) 1.5 (2.32) 1.4 (31.34) /1U2 1.43 (4.35) 1.671 (42.44) 1.347 (34.) 1.641 (41.6) 1.0 (31.50) 1.4 (31.34) /1U2 1.43 (4.35) 1.766 (44.6) 1.472 (37.3) 1.766 (44.6) 1.365 (34.67) 1.4 (31.34) /1U2 1.43 (4.35) 1.766 (44.6) 1.57 (40.56) 1.1 (4.03) 1.40 (37.5) 1.4 (31.34) /1U2 1.43 (4.35) 1.766 (44.6) erformance Specificationsages 3 and 4. ontacts, Sealing lugs, ssembly Tools ages, 31 and 32. ontact rrangements ages and. *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent.
3Style Series onnectors* Jam ut Receptacle S2746Style (S service class,,t) KJL7 U X. HX OLRZG KYWY. (.37) X. X..062 (1.57). L THKSS H T THRD S J D. D D. D. V THRD LU D (DTS RR RLS OTT RTTO SYST) OT: or backshell dimensions and configurations, see pages 2 and 31. Overall Length With ackshells Dia. ax. D ax..573 (.55).655 (.64).701 (.1).755 (.1).51 (.62).42 (.3).76 (.7) 1.066 (27.0) 1.1 (27.7) 1.1 (30.) 1. (30.6) 1.3 (33.43) 1.333 (33.6) 1.441 (36.60) 1.45 (37.03) 1.566 (3.7) 1.53 (40.) 1.61 (42.5) H ax..1 (3.05).1 (3.05).1 (3.05).1 (3.05).1 (3.05).1 (3.4).1 (3.4).1 (3.4).1 (3.4) J Dia. ax..662 (.1). (.57).60 (.3) S Dia. ax. 1.4 (30.5) 1.31 (35.33) 1.5 (35.51) 1.05 (27.56) 1.641 (41.6) 1.0 (30.73) 1.766 (44.6) 1.3 (33.45) 1.54 (4.63) 1.442 (36.63) 2.07 (52.7) 1.567 (3.0) 2.4 (55.) 1.62 (42.) 2.32 (5.) T Thread 7/2U2 /U2 /U2 /U2 /U2 /1U2 /1U2 /1U2 /1U2 U ax. Hex..2 (.66) V Thread lass 2 /U 1.0 (.3) /U 1.5 (30.61) 1U 1.32 (33.76) /1U 1.455 (36.6) /41U 1.57 (40.) /1U 1.705 (43.31) /U 1.2 (46.46) /1U. (51.) /41US able lamp 1.46 (46.) 1.46 (46.) 1.46 (46.) 1.46 (46.) 1.66 (4.4) 1.6 (50.70) 1.6 (50.70) 1.6 (50.70) 1.6 (50.70) otting ax. 1.451 (36.6) 1.451 (36.6) 1.451 (36.6) 1.451 (36.6) 1.451 (36.6) 1.451 (36.6) 1.451 (36.6) 1.451 (36.6) 1.451 (36.6) erformance Specificationsages 3 and 4. ontacts, Sealing lugs, ssembly Tools ages, 31, and 32. ontact rrangements ages,. anel utouts lange ounted Receptacles Jam ut Receptacles ±.005 (0.) 4 HOLS R (T.) +.0 (0.).000 (0.00) Dia..665 (.). (.62).65 (.51) 1.05 (27.55) 1.0 (31.75) 1.3 (33.57) 1.447 (36.75) 1.56 (3.5) 1.703 (43.) Dia.. (3.). (3.). (3.). (3.). (3.). (3.). (3.).4 (3.1).0 (3.1) (lass T) R.7 (1.26). (.62).06 (.01).6 (.61) 1.062 (26.7) 1.6 (2.36) 1.0 (31.75) 1.375 (34.3) 1.500 (3.) tg. Screw #4 #4 #4 #4 #4 #4 #4 #6 #6 +.0 (.).000 (.00).700 (.7). (.6) 1.0 (.65) 1.5 (2.3) 1.260 (32.00) 1.35 (35.1) 1.5 (3.35) 1.635 (41.53) 1.760 (44.70) +.000 (.00).0 (.).670 (.02).771 (.5).55 (.26) 1.05 (27.56) 1.0 (30.73) 1.335 (33.1) 1.460 (37.0) 1.55 (40.26) 1.7 (43.43) *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent.
3Style Series onnectors* How To Order ilitary omenclature DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent. S UR SHLL STYL S27472 Wall ounting Receptacle S27473 Straight lug S27474 Jam ut Receptacle S2744 Grounded lug S2747 Wall ounting Receptacle (back panel mounting) S275 ox ounting Receptacle S274 ox ounting Receptacle (lass ) S2750 ox ounting (back panel mounting) (lass ) LSS nvironment resistant with rear accessory (without strain relief) G nvironmental resistant wall mount and jam nut receptacle and plug types. Space Grade. nironment resistant with straight potting cup accessories T nvironment resistant (without rear accessory). (lass T not applicable to S274, S275, and S2750.) S UR SHLL STYL LSS SHLL SZ HRDWR SH OTT RRGT OTT STYL OLRZG OSTO SHLL SZ,,,,, 1,,,. HRDWR SH STDRD right cadmium over electroless nickel plate, 5º to + 302º ( 65º to + 0º) Olive drab cadmium over electoless nickel plate, 5º to + 347º ( 65º to + 5º) lectroless nickel, 5º to + 32º (65º to + 0º) OTT RRGT See pages and. OTT STYL in S Socket * Less in ontact * Less Socket ontact S27473Style T 1 35 S *Used only when other than power contacts are to be installed (i.e. shielded, thermocouple, etc.) OLRZG OSTO,,, and D (no letter required for normal). See page. ote: To order S connectors less standard power contacts, purchase order must state Less ontacts. TT omenclature SRS RX KJ Series Low rofile SHLL STYL 0 Wall mounting receptacle 2 ox mounting receptacle 3 Wall mounting receptacle (back panel mounting) 5 ox mounting receptacle (back panel mounting) 6 Straight plug G6 Straight plug, grounded 7 Jam nut receptacle LSS nvironment resistant with rear accessory (without strain relief) nvironment resistant with strain relief acccessory G nvironmental resistant wall mount and jam nut receptacle and plug type. Space Grade. nvironment resistant with straight potting cup accessory R nvironment resistant with full grommet seal without rear accessory; shell styles 2 and 5 only T nvironment resistant (without rear accessory). (lass T not applicable to KJ2, KJ2R, KJ5 and KJ5R.) SRS RX SHLL STYL LSS SHLL SZ HRDWR SH OTT RRGT OTT STYL OLRZG OSTO ODTO OD ote KJ supplied with exact complement of contacts. SHLL SZ,,,,, 1,,, and. HRDWR SH STDRD right cadmium over electroless nickel plate, 5º to + 302º ( 65º to + 0º) Olive drab cadmium over electroless nickel plate, 5º to + 347º ( 65º to + 5 ) lectroless nickel, 5º to + 32º (65º to + 0º) Z Zinc ickel, lack (Dash) When using a finish modification code OTT RRGT See pages and. OTT STYL in S Socket KJ 6 T 1 35 S OLRZG OSTO (normal),,,, D, see page. ODTO OD L Less contacts, not stamped on connector Outgassed S space graded connector linch uts installed (440 ) 27 Outgassed, standard connector 26 lack Znc obalt, RoHS ompliant *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent.
3Style Series onnectors* Wall ounting Receptacle S27472Style (S service class,, T) KJ0 OLRZG KYWY.3 (.) X. T THRD J X. D. D. LU D (DTTS RR RLS OTT RTTO SYST).06 (1.74) X. OT: or backshell dimensions and configurations, see pages 2 and 31. 1 Dia. ax..474 (.04).51 (.01).751 (.0).76 (.) 1.001 (.43) 1.6 (2.60) 1.1 (31.7) 1.376 (34.5) 1.501 (3.) J Dia. ax..563 (.30).60 (.27).5 (.2).4 (.) 1. (2.) 1.3 (31.32) 1.35 (34.4) 1.43 (37.67) 1.6 (40.) ax..2 (.03).54 (.) 1.047 (26.5) 1.1 (2.) 1.4 (31.34) 1.32 (33.73) 1.453 (36.1) 1.57 (3.0) 1.703 (43.26) T..54 (.0).7 (1.26). (.62).06 (.01).6 (.61) 1.062 (26.7) 1.6 (27.36) 1.0 (31.76) 1.375 (34.2) +.005 (0.).0 (0.).2 (3.6) T Thread 7/2U2 /U2 /U2 /U2 /U2 /1U2 /1U2 /1U2 /1U2 Straight.50 (.5).50 (.5).50 (.5).50 (.5).50 (.5).50 (.5).50 (.5).50 (.5).50 (.5) Overall length With ackshells able lamp 1.555 (3.50) 1.555 (3.50) 1.555 (3.50) 1.70 (45.47) 1.70 (45.47) 1.70 (45.47) 1.70 (45.47) 1.30 (4.02) 1.00 (4.26) otting ax. 1.0 (.1) 1.0 (.1) 1.0 (.1) 1.0 (.1) 1.0 (.1) 1.0 (.1) 1.0 (.1) 1.0 (.1) 1.00 (27.43) ox ounting Receptacle S274Style (S service class ) KJ2 OLRZG KYWY.3 (.) X. L J X. D. G D. D. LU D (DTTS RR RLS OTT RTTO SYST).06 (1.74) X. OT: This connector does not accommodate backshells 1 Dia. ax..474 (.04).51 (.01).751 (.0).76 (.) 1.001 (.43) 1.6 (2.60) 1.1 (31.7) 1.376 (33.5) 1.501 (3.) G Dia. ax..4 (.6).542 (.77).667 (.4).71 (.0). (.27) 1.034 (26.26) 1. (2.41) 1.23 (32.5) 1.40 (35.76) J Dia. ax..563 (.30).60 (.27).5 (.2).4 (.) 1. (2.) 1.3 (31.32) 1.35 (34.4) 1.43 (37.67) 1.6 (40.) L ax..3 (7.2).3 (7.2).3 (7.2).3 (7.2).3 (7.2).3 (7.2).3 (7.2).3 (7.2).3 (7.2) ax..2 (.03).54 (.) 1.047 (26.5) 1.1 (2.) 1.4 (31.34) 1.32 (33.73) 1.453 (36.1) 1.57 (40.0) 1.703 (43.26) T...54 (.0).7 (1.26). (.62).06 (.01).6 (.61) 1.062 (26.7) 1.6 (27.36) 1.0 (31.75) 1.375 (34.3) +.005 (0.).0 (0.).2 (3.6) erformance Specificationsages 3 and 4. ontacts, Sealing lugs, ssembly Tools ages, 31, and 32. ontact rrangements ages and. *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent.
3Style Series onnectors* ox ounting Receptacle S275Style (S service class ) KJ2R.3 (.) X. L.463 (.76) X. OLRZG KYWY J X. D. G D. LU D (DTS RR RLS OTT RTTO SYST).06 (1.74) X. D. 1 Dia. ax..474 (.04).51 (.01).751 (.0).76 (.) 1.001 (.43) 1.6 (2.60) 1.1 (31.7) 1.376 (33.5) 1.501 (3.) G Dia. ax..4 (.6).542 (.77).667 (.4).71 (.0). (.27) 1.034 (26.26) 1. (2.41) 1.23 (32.5) 1.40 (35.76) OT: This connector does not accommodate backshells J Dia. ax..563 (.30).60 (.27).5 (.2).4 (.) 1. (2.) 1.3 (31.32) 1.35 (34.4) 1.43 (27.67) 1.6 (40.) L ax..3 (7.2).3 (7.2).3 (7.2).3 (7.2).3 (7.2).3 (7.2).3 (7.2).3 (7.2).3 (7.2) ax..2 (.03).54 (.) 1.047 (26.5) 1.1 (2.) 1.4 (31.34) 1.32 (33.73) 1.453 (36.1) 1.57 (40.0) 1.703 (43.26) T...54 (.0).7 (1.26). (.62).06 (.01).6 (.61) 1.062 (26.7) 1.6 (27.36) 1.0 (31.75) 1.375 (34.3) +.005 (0.).0 (0.).2 (3.5) Wall ounting Receptacle S2747Style (S service class,, T) KJ3.2 (3.01) X. L THKSS (including mounting hardware).477 (.35) X..3 (.) X. T THRD D. OLRZG KYWY D. D. J D. LU D (DTS RR RLS OTT RTTO SYST).06 (1.74) X. OT: or backshell dimensions and configurations, see pages 2 and 31. 1 Dia. ax..474 (.04).51 (.01).751 (.0).76 (.) 1.001 (.43) 1.6 (2.60) 1.1 (31.7) 1.376 (34.5) 1.501 (3.) Dia. ax..5 (.26).63 (.).0 (.52).35 (.75) 1.05 (26.7) 1.13 (30.05) 1.30 (33.) 1.433 (36.40) 1.56 (3.3) J Dia. ax..563 (.30).60 (.27).5 (.2).4 (.) 1. (2.) 1.3 (31.32) 1.35 (34.4) 1.43 (37.67) 1.6 (40.) ax..2 (.03).54 (.) 1.047 (26.5) 1.1 (2.) 1.4 (31.34) 1.32 (33.73) 1.453 (36.1) 1.57 (40.0) 1.703 (43.26) T..54 (.0).7 (1.26). (.62).06 (.01).6 (.61) 1.062 (26.7) 1.6 (2.36) 1.0 (31.75) 1.375 (34.3) +.005 (0.).0 (0.) T Thread 7/2U2 /U2 /U2 /U2 /U2 /1U2 /1U2 /1U2.2 (3.6) /1U2 Overall Length With ackshells Straight able lamp.55 (.72) 1.570 (3.).55 (.72) 1.570 (3.).55 (.72) 1.570 (3.).55 (.72) 1.70 (45.).55 (.72) 1.70 (45.).55 (.72) 1.70 (45.).55 (.72) 1.70 (45.).55 (.72) 1.60 (4.7).55 (.72) 1.60 (4.7) otting ax. 1.0 (.1) 1.0 (.1) 1.0 (.1) 1.0 (.1) 1.0 (.1) 1.0 (.1) 1.0 (.1) 1.0 (.1) 1.00 (27.43) erformance Specificationsages 3 and 4. ontacts, Sealing lugs, ssembly Tools ages, 31, and 32. ontact rrangements ages and. *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent.
3Style Series onnectors* ox ounting Receptacle (ack anel) (S service class ) S2750Style (S service class ) KJ5.447 (.35) X..3 (.) X. L D. OLRZG KYWY J D. G D. LU D (DTS RR RLS OTT RTTO SYST).06 (1.74) X. K X. L THKSS (including mounting hardware) 1 Dia. ax..474 (.04).51 (.01).751 (.0).76 (.) 1.001 (.42) 1.6 (2.60) 1.1 (31.77) 1.376 (34.5) 1.501 (3.) Dia. ax..5 (.26).63 (.).0 (.52).35 (.75) 1.05 (26.7) 1.13 (30.05) 1.30 (33.) 1.433 (36.40) 1.56 (3.3) OT: This connector does not accommodate backshells G Dia. ax. J Dia. ax. K ax. L ax. ax..4 (.6).563 (.30).7 (3.73). (4.70).2 (.03).542 (.77).60 (.27).2 (3.6). (4.70).54 (.).667 (.4).5 (.2).2 (3.6). (4.70) 1.047 (26.5).71 (.0).4 (.).2 (3.6). (4.70) 1.1 (2.). (.27) 1. (2.).2 (3.6). (4.70) 1.4 (31.) 1.034 (31.34) 1.3 (31.32).2 (3.6). (4.70) 1.32 (33.73) 1. (34.52) 1.35 (34.4). (4.55). (4.70) 1.453 (36.1) 1.23 (32.5) 1.43 (37.67). (4.55). (4.70) 1.57 (40.0) 1.40 (35.76) 1.6 (40.). (4.2). (4.70) 1.703 (43.66) T..54 (.0).7 (1.26). (.62).06 (.01).6 (.61) 1.062 (26.7) 1.6 (2.36) 1.0 (31.75) 1.375 (34.2) +.005 (0.).0 (0.).2 (3.6) ox ounting Receptacle (ack anel) o S part number KJ5R.447 (.35) X. L D. OLRZG KYWY..3 (.) X..33 (.5) X. J D. G D. LU D (DTS RR RLS OTT RTTO SYST).06 (1.74) X. K X. L THKSS (including mounting hardware) OT: This connector does not accommodate backshells 1 Dia. ax..474 (.04).51 (.01).751 (.0).76 (.) 1.001 (.42) 1.6 (2.60) 1.1 (31.77) 1.376 (34.5) 1.501 (3.) Dia. ax..5 (.26).63 (.).0 (.52).35 (.75) 1.05 (26.7) 1.13 (30.05) 1.30 (33.) 1.433 (36.40) 1.56 (3.3) G Dia. ax..4 (.6).542 (.77).667 (.4).71 (.0). (.27) 1.034 (31.34) 1. (34.52) 1.23 (32.5) 1.40 (35.76) J Dia. ax..563 (.30).60 (.27).5 (.2).4 (.) 1. (2.) 1.3 (31.32) 1.35 (34.4) 1.43 (37.67) 1.6 (40.) K ax..7 (3.73).2 (3.6).2 (3.6).2 (3.6).2 (3.6).2 (3.6). (4.55). (4.55). (4.2) L ax.. (4.70). (4.70). (4.70). (4.70). (4.70). (4.70). (4.70). (4.70). (4.70) ax..2 (.03).54 (.) 1.047 (26.5) 1.1 (2.) 1.4 (31.) 1.32 (33.73) 1.453 (36.1) 1.57 (40.0) 1.703 (43.66) T..54 (.0).7 (1.26). (.62).06 (.01).6 (.61) 1.062 (26.7) 1.6 (2.36) 1.0 (31.75) 1.375 (34.2) +.005 (0.).0 (0.).2 (3.6) erformance Specificationsages 3 and 4. ontacts, Sealing lugs, ssembly Tools ages, 31, and 32. ontact rrangements ages and. *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent.
3Style Series onnectors* Straight lug S27473Style (S service class,, T) KJ6 OLRZG KYWY T THRD D. D. G D. LU D (DTS RR RLS OTT RTTO SYST) OT: or backshell dimensions and configurations, see pages 2 and 31. 1 Dia. ax..45 (.32).606 (.3).765 (.43).0 (.61) 1.0 (.76) 1.0 (2.6) 1.264 (32.) 1.3 (35.2) 1.5 (3.46) G Dia. ax..74 (.02).5 (.7) 1.030 (26.) 1.5 (2.34) 1.20 (32.51) 1.405 (35.6) 1.530 (3.6) 1.640 (40.66) 1.765 (44.3) Dia. ax..630 (.00).752 (.). (.50) 1.050 (26.67) 1.2 (2.77) 1.304 (33.) 1.435 (36.45) 1.560 (3.62) 1.6 (42.) T Thread 7/2U2 /U2 /U2 /U2 /U2 /1U2 /1U2 /1U2 /1U2 Overall Length With ackshells Straight able lamp otting ax. 1.026 (26.06) 1.555 (3.50) 1.0 (.1) 1.026 (26.06) 1.555 (3.50) 1.0 (.1) 1.026 (26.06) 1.555 (3.50) 1.0 (.1) 1.026 (26.06) 1.70 (45.47) 1.0 (.1) 1.026 (26.06) 1.70 (45.47) 1.0 (.1) 1.026 (26.06) 1.70 (45.47) 1.0 (.1) 1.026 (26.06) 1.70 (45.47) 1.0 (.1) 1.026 (26.06) 1.30 (4.02) 1.0 (.1) 1.4 (2.04) 1.30 (4.02) 1.00 (27.43) Straight lug Grounded S2744Style (S service class,, T) KJG6 OLRZG KYWY T THRD D. D. G D. LU D (DTS RR RLS OTT RTTO SYST) OT: or backshell dimensions and configurations, see pages 2 and 31. Dia. ax. G Dia. ax. Dia. ax. 1.45 (.32).606 (.3).765 (.43).0 (.61) 1.0 (.76) 1.0 (2.6) 1.264 (32.) 1.3 (35.2) 1.5 (3.46).74 (.02).5 (.7) 1.030 (26.) 1.5 (2.34) 1.20 (32.51) 1.405 (35.6) 1.530 (3.6) 1.640 (40.66) 1.765 (44.3).630 (.00).752 (.). (.50) 1.050 (26.67) 1.2 (2.77) 1.304 (33.) 1.435 (36.45) 1.560 (3.62) 1.6 (42.) erformance Specificationsages 3 and 4. ontacts, Sealing lugs, ssembly Tools ages, 31, and 32. ontact rrangements ages and. T Thread 7/2U2 /U2 /U2 /U2 /U2 /1U2 /1U2 /1U2 /1U2 Overall Length With ackshells Straight able lamp otting ax. 1.026 (26.06) 1.555 (3.50) 1.0 (.1) 1.026 (26.06) 1.555 (3.50) 1.0 (.1) 1.026 (26.06) 1.555 (3.50) 1.0 (.1) 1.026 (26.06) 1.70 (45.47) 1.0 (.1) 1.026 (26.06) 1.70 (45.47) 1.0 (.1) 1.026 (26.06) 1.70 (45.47) 1.0 (.1) 1.026 (26.06) 1.70 (45.47) 1.0 (.1) 1.026 (26.06) 1.30 (4.02) 1.0 (.1) 1.4 (2.04) 1.30 (4.02) 1.00 (27.43) *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent.
3Style Series onnectors* Jam ut Receptacle S27474Style (S service class,, T) KJ7 G. (2.77) X. L THKSS T THRD R OLRZG KYWY V THRD LU D (DTS RR RLS OTT RTTO SYST).5 (2.66) X. S D. J D. D OUTG LT OT: or backshell dimensions and configurations, see pages 2 and 31. 1 Dia. ax. D ax. G ax. J ax. ax. R ax. Hex. S Dia. ax. T Thread.474 (.04).51 (.01).1 (.7).42 (.3).5 (3.6).5 (3.6).563 (.30).60 (.27).443 (.).443 (.) 1.07 (27.41) 1.5 (30.61) 1.31 (35.0) 1.506 (3.) 7/2U2 /U2.751 (.0).76 (.) 1.066 (27.0).5 (3.6) 1.1 (30.).5 (3.6).5 (.2).4 (.).443 (.).443 (.) 1.32 (33.76) 1.455 (36.6) 1.631 (41.43) 1.756 (44.60) /U2 /U2 1.001 (.43) 1.3 (33.55).5 (3.6) 1. (2.).443 (.) 1.57 (40.) 1.44 (4.3) 5/U2 1.6 (2.60) 1.441 (36.60).5 (3.6) 1.1 (31.7) 1.566 (3.7).1 (4.34) 1.376 (33.5) 1.61 (42.5).1 (4.34) 1.501 (3.) 1. (46.).1 (4.34) 1.3 (31.32).443 (.) 1.35 (34.4).46 (.1) 1.43 (37.67).46 (.1) 1.6 (40.).46 (.1) 1.705 (43.31) 1.2 (46.46) 2.0 (51.) 2.2 (54.41) 2.0 (51.36) 2.7 (54.53) 2.271 (57.6) 2.36 (60.6) /1U2 /1U2 /1U2 /1U2 erformance Specificationsages 3 and 4. ontacts, Sealing lugs, ssembly Tools ages, 31, and 32. ontact rrangements ages and. V Thread 7/U2 1U2 /1U2 /41U2 /1U2 /U2 /1U2 /41US2 /1US2 Overall length With ackshells Straight.40 (.34).40 (.34).40 (.34).40 (.34).40 (.34).40 (.34).40 (.34).40 (.34).60 (.4) able lamp 1.555 (3.50) 1.555 (3.50) 1.555 (3.50) 1.70 (45.47) 1.70 (45.47) 1.70 (45.47) 1.70 (45.47) 1.30 (4.02) 1.00(4.26) otting ax. 1.0 (.1) 1.0 (.1) 1.0 (.1) 1.0 (.1) 1.0 (.1) 1.0 (.1) 1.0 (.1) 1.0 (.1) 1.00 (27.43) anel utouts lange ounted Receptacle +_.005 (0.) 4 HOLS Jam ut Receptacle R (T..) +.000 (0.00).0 (0.) +.0 (0.).000 (0.00) +.0 (0.).000 (0.00) 1 Dia..6 (.4).734 (1.64).60 (.4).5 (.02) 1.0 (2.) 1.4 (31.34) 1.360 (35.54) 1.44 (37.6) 1.6 (40.2) Dia..2 (3.6) R.54 (.0).7 (1.26). (.62).06 (.01).6 (.61) 1.062 (26.7) 1.6 (2.36) 1.0 (31.75) 1.375 (34.3) fg. Screw #4 #4 #4 #4 #4 #4 #4 #4 #6 1 Dia..5 (.4) 1.0 (.65) 1.5 (2.2) 1.260 (32.00) 1.35 (35.1) 1.5 (3.35) 1.635 (41.53) 1.760 (44.70) 1.5 (47.) Dia..30 (.0).55 (.26) 1.05 (27.56) 1.0 (30.73) 1.335 (33.1) 1.460 (37.0) 1.55 (40.26) 1.7 (43.43) 1.35 (46.61) *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent.
3Style Series onnectors* How To Order ilitary omenclature D3Style 35 OTOR TY DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/ QL. ilspec part numbers are only for cross reference to the ommercial quivalent. SHLL STYL SRV LSS (HRDWR SH) SHLL SZ OTT RRGT OTT STYL OLRZG OSTO OTOR TY D3Style Series SHLL STYL D3/Style Wall mount receptacle D3/Style Jam nut receptacle D3/26Style Straight lug, Grounded SRV LSS (Hardware inish) lectroless nickel 5º to +32º (65º to +0º) G lectroless nickel plated. Space Grade. W Olive drab cadmium over electroless nickel plate, 5º to +347º (65º to +5º) OTT RRGT See pages,. OTT STYL in contacts S Socket contact Less in contacts* Less Socket contact* * Used only when other than power contacts are to be installed (i,e., shielded, thermocouple, etc.) OLRZG OSTO (normal),,,, D,. See page. SHLL SZ D G H J ilitary Designation ote: To order S connectors less standard power contacts, purchase order must state Less ontacts. annon Designation annon omenclature SRS RX SHLL STYL LSS SHLL SZ HRDWR SH OTT RRGT OTT STYL OLRZG OSTO ODTO OD KJ 0 T 35 L SRS RX KJ/KJ* Series Scoop proof, threaded coupling SHLL STYL 0 Wall mount receptacle 5 ox mount receptacle* 6 Straight plug 7 Jam nut receptacle LSS T nvironmentresistant (without rear accessory) * onsult factory for availability SHLL SZ annon Designation D G H J ilitary Designation HRDWR SH lectroless nickel, 5º to +32º (65º to +0º) G lectroless nickel plated. Space Grade. W Olive drab cadmium over electroless nickel plate, 5º to +347º (65º to +5º) Z Zinc ickel, lack (Dash) When using a finish modification code OTT RRGTS See pages and. *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent. OTT STYL in contacts S Socket contacts OLRZG OSTO (normal),,, D,. See page. ODTO OD L Less contacts, not stamped on connector Outgassed S space graded connector linch uts installed (440, 632 ) 27 Outgassed, standard connector 26 lack Zinc obalt, RoHS ompliant See page 26 for ordering Standoff ontacts using modification codes.
3Style Series onnectors* Wall ount Receptacle D3/Style KJ0/KJ0 S Z R 1 R 2 THRD W X. V THRD TT 4 LS T 4 LS LU D (DTS RR RLS OTT RTTO SYST) RD D (ULLY TD DTOR D).0 X L THKSS (including mounting hardware).5 (.) X S size ode Thread lass 2 (lated).600..3lts +.000 (.000).005 (.0). (.3) R 1 R 2.7 (1.26).54 (.0) T TT S +_.0 (.300) +.004 (.0) +.004 (.0).002 (.050).002 (.050).3 (.3). (3.).2 (5.4) etric V Thread (lated) Xg0.0R W ax..0 (2.50) Z +.005 (.0).0 (.0) 1.5 (31.36).75000..3LTS. (.3). (.62).7 (1.26) 1.031 (26.). (3.).4 (4.3) Xg0.0R.0 (2.50) 1.5 (31.36).7500..3LTS. (.3).06 (.01). (.62) 1.5 (2.5). (3.).4 (4.3) 1Xg0.0R.0 (2.50) 1.5 (31.36) D 1.00000..3LTS. (.3).6 (.61).06 (.01) 1. (30.6). (3.).3 (4.3) Xg0.0R.0 (2.50) 1.5 (31.36) 1.50..3LTS. (.3) 1.062 (26.7).6 (.61) 1.3 (33.32). (3.).4 (4.3) Xg0.0R.0 (2.50) 1.5 (31.36) 1.000..3LTS. (.3) 1.6 (2.36) 1.062 (26.7) 1.43 (36.53). (3.).4 (4.3) 2Xg0.0R.0 (2.50) 1.5 (31.36) G 1.37500..3LTS.70 (.07) 1.0 (31.75) 1.6 (2.36) 1.562 (3.67). (3.).4 (4.3) 31Xg0.0R.6 (3.) 1.5 (31.36) H 1.50000..3LTS.70 (.07) 1.375 (34.2) 1.0 (31.75) 1.6 (42.).4 (3.1).2 (6.) 34Xg0.0R.6 (3.) 1.5 (31.36) J 1.600..3LTS.70 (.07) 1.500 (3.) 1.375 (34.2) 1. (46.02).4 (3.1).2 (6.) 37Xg0.0R.6 (3.) 1.5 (31.36) Straight lug Grounded D3/26Style KJ6/KJ6 L Q D THRD W K.4 (6.)+.0 (0.30).000 (0.00) LU D (DTS RR RLS OTT RTTO SYSTS V THRD. (4.70) +_.0 (0.40) S size ode D G H J +.00 (.0).000 (.000).7 (1.40).31 (.) 1.000 (.40) 1.0 (2.70) 1.26 (32.) 1.374 (34.0) 1.500 (3.) 1.61 (41.40) 1.744 (44.30) D Thread lass 2 (lated).600..3lts.75000..3lts.7500..3lts 1.00000..3LTS 1.50..3LTS 1.000..3LTS 1.37500..3LTS 1.50000..3LTS 1.600..3LTS K ax..74 (.00).62 (.0) 1.027 (26.) 1.3 (2.30) 1.21 (32.0) 1.3 (35.50) 1.5 (3.70) 1.642 (41.70) 1.76 (44.0) L ax. 1.4 (31.34) 1.4 (31.34) 1.4 (31.34) 1.4 (31.34) 1.4 (31.34) 1.4 (31.34) 1.4 (31.34) 1.4 (31.34) 1.4 (31.34) Q Dia ax..5 (.2).6 (.61) 1.1 (2.) 1.266 (32.) 1.31 (35.53) 1.500 (3.) 1.6 (41.2) 1.750 (44.45) 1.75 (47.62) etric V Thread (lated) Xg0.0R Xg0.0R 1Xg0.0R Xg0.0R Xg0.0R 2Xg0.0R 31Xg0.0R 34Xg0.0R 37Xg0.0R W +.00 (.0).004 (.0).760 (.30).760 (.30).760 (.30).760 (.30).760 (.30).760 (.30).760 (.30).760 (.30).760 (.30) erformance Specificationsages 3 and 4. ontacts, Sealing lugs, ssembly Tools ages, 31, and 32. ontact rrangements ages and. *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent.
3Style Series onnectors* Jam ut Receptacle D3/Style KJ7/KJ7 S LT S THRD Z LU D (DTS RR RLS OTT RTTO SYST).5 (.2) X. RD D (ULLY TD DTOR D) V THRD R THRD.062 (1.57)./ X. L THKSS S size +.0 (.0) ode.005 (.0).4 (2.64).4 (2.64).4 (2.64) D.4 (2.64).4 (2.64).5 (3.43) G.5 (3.43) H.5 (3.43) J.5 (3.43) Thread lass 2 (lated).600..3lts.75000..3lts.7500..3lts 1.00000..3LTS 1.50..3LTS 1.000..3LTS 1.37500..3LTS 1.50000..3LTS 1.600..3LTS +.004 (.0).0 (.0).651 (.53).751 (.07).3 (.2) 1.062 (26.7) 1. (30.) 1.3 (33.32) 1.437 (36.50) 1.562 (3.67) 1.67 (42.5) erformance Specificationsages 3 and 4. ontacts, Sealing lugs, ssembly Tools ages, 31, and 32. ontact rrangements ages and. Z +.005 (.0).040 (.0) 1.3 (31.57) 1.3 (31.57) 1.3 (31.57) 1.3 (31.57) 1.3 (31.57) 1.3 (31.57) 1.3 (31.57) 1.3 (31.57) 1.3 (31.57) +.005 (.0).004 (.0).71 (.).71 (.).7 (.30).7 (.30).7 (.30).7 (.30).7 (.30).7 (.30).7 (.30) anel utouts +.0 (.4).004 (.0).555 (.).555 (.).563 (.30).563 (.30).563 (.30).563 (.30).563 (.30).563 (.30).563 (.30) S 1.062 (26.7) 1.0 (31.75) 1.375 (34.2) 1.500 (3.) 1.6 (41.2) 1. (46.02) 1.3 (4.) 2.062 (52.37) 2.1 (55.3) etric R Thread (lated) Xg0.0R Xg0.0R Xg0.0R 2Xg0.0R 32Xg0.0R 35Xg0.0R 3Xg0.0R 41Xg0.0R 44Xg0.0R etric V Thread (lated) Xg0.0R Xg0.0R 1Xg0.0R Xg0.0R Xg0.0R 2Xg0.0R 31Xg0.0R 34Xg0.0R 37Xg0.0R Wall ounted Receptacle Jam ut Receptacle +.0 (.).000 (.00).63 (.6). (.6) 1.0 (.65) 1.5 (2.3) 1.260 (32.00) 1.35 (35.1) 1.5 (3.35) 1.635 (41.53) 1.760 (44.70) +.000 (.00)*.0 (.).657 (.70).771 (.5).55 (.26) 1.05 (27.56) 1.0 (30.73) 1.335 (33.1) 1.460 (37.0) 1.55 (40.26) 1.7 (43.43) ØH1 (in.).656 (.66).76 (.). (.42) 1.047 (26.5) 1. (30.6) 1.27 (32.4) 1.4 (36.) 1.547 (3.2) 1.672 (42.47) ØH2 (in.).5 (.).6 (.).750 (.05).06 (.01) 1.0 (.1) 1.1 (2.) 1.266 (36.) 1.375 (34.2) 1.44 (37.6) R (T).7 (1.26). (.62).06 (.01).6 (.61) 1.062 (26.7) 1.6 (2.36) 1.0 (31.75) 1.375 (34.2) 1.500 (3.) ØT ±.050 (.). (3.). (3.). (3.). (3.). (3.). (3.). (3.).4 (31).0 (3.1) * or Dimension, only, tolerance is ±.004 (.) *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent. 1
3Style Series omposite onnectors* How To Order ilitary omenclature D3Style 35 DSLR:Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent. OTOR TY SHLL STYL SRV LSS (HRDWR SH) SHLL SZ OTT RRGT OTT STYL OLRZG OSTO OTOR TY D3/ 3Style Series SHLL STYL D3/ Wall mount receptacle D3/26 Straight lug, Grounded SRV LSS (Hardware inish) J Olive drab cadmium over electroless nickel plate, 5º to +347º (65º to +5º) lectroless nickel 5º to +32º (65º to +0º), RoHS ompliant OTT RRGT See pages,. OTT STYL H in conatcts (00 cycle) J Socket contacts (00 cycle) in conatcts S Socket contact Less in contacts* Less Socket contact* * Used only when other than power contacts are to be installed (i,e., shielded, thermocouple, etc.) SHLL SZ D G H ilitary J Designation annon Designation OLRZG OSTO (normal),,,, D,. See page. ote: To order S connectors less standard power contacts, purchase order must state Less ontacts. annon omenclature SRS RX KJ* Series Scoop proof, threaded coupling SHLL STYL 0 Wall mount receptacle 6 Straight plug LSS T nvironmentresistant (without rear accessory) * onsult factory for availability SRS RX SHLL STYL LSS SHLL SZ HRDWR SH OTT RRGT OTT STYL OLRZG OSTO ODTO OD SHLL SZ annon Designation D G H J ilitary Designation HRDWR SH J Olive drab cadmium over electroless nickel plate, 5º to +347º (65º to +5º) lectroless nickel, 5º to +32º (65º to +0º), RoHS ompliant OTT RRGTS See pages and. KJ 0 T 35 L OTT STYL H in conatcts (00 cycle) J Socket contacts (00 cycle) in contacts S Socket contacts OLRZG OSTO (normal),,, D,. See page. ODTO OD L Less contacts, not stamped on connector *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent.
3Style Series omposite onnectors* Wall ount Receptacle D3/Style KJ0T S Z R 1 R 2 THRD W X. V THRD TT 4 LS T 4 LS LU D (DTS RR RLS OTT RTTO SYST) RD D (ULLY TD DTOR D).0 X L THKSS (including mounting hardware).5 (.) X S size ode Thread lass 2 (lated).600..3lts +.000 (.000).005 (.0).76 (.50) R 1 R 2.7 (1.26).54 (.0) T TT S +_.0 (.300) +.004 (.0) +.004 (.0).002 (.050).002 (.050).3 (.3). (3.).2 (5.4) etric V Thread (lated) Xg0.0R W ax..3 (3.63) Z +.005 (.0).0 (.0) 1.5 (32.00).75000..3LTS.76 (.50). (.62).7 (1.26) 1.031 (26.). (3.).4 (4.3) Xg0.0R.3 (3.63) 1.5 (32.00).7500..3LTS.76 (.50).06 (.01). (.62) 1.5 (2.5). (3.).4 (4.3) 1Xg0.0R.3 (3.63) 1.5 (32.00) D 1.00000..3LTS.76 (.50).6 (.61).06 (.01) 1. (30.6). (3.).3 (4.3) Xg0.0R.3 (3.63) 1.5 (32.00) 1.50..3LTS.76 (.50) 1.062 (26.7).6 (.61) 1.3 (33.32). (3.).4 (4.3) Xg0.0R.3 (3.63) 1.5 (32.00) 1.000..3LTS.76 (.50) 1.6 (2.36) 1.062 (26.7) 1.43 (36.53). (3.).4 (4.3) 2Xg0.0R.3 (3.63) 1.5 (32.00) G 1.37500..3LTS.736 (1.70) 1.0 (31.75) 1.6 (2.36) 1.562 (3.67). (3.).4 (4.3) 31Xg0.0R.1 (4.35) 1.5 (32.00) H 1.50000..3LTS.736 (1.70) 1.375 (34.2) 1.0 (31.75) 1.6 (42.).4 (3.1).2 (6.) 34Xg0.0R.1 (4.35) 1.5 (32.00) J 1.600..3LTS.736 (1.70) 1.500 (3.) 1.375 (34.2) 1. (46.02).4 (3.1).2 (6.) 37Xg0.0R.1 (4.35) 1.5 (32.00) Straight lug Grounded D3/26Style KJ6T Q D THRD L LU D (DTS RR RLS OTT RTTO SYSTS V THRD S size ode D G H J erformance Specificationsages 3 and 4. ontacts, Sealing lugs, ssembly Tools ages, 31, and 32. ontact rrangements ages and. +.00 (.0).000 (.000). (.6).2 (.6) 1. (2.2) 1. (31.3) 1.35 (34.5) 1.46 (37.3) 1.5 (40.5) 1.72 (43.7) 1.4 (46.) L ax. 1. (31.5) 1. (31.5) 1. (31.5) 1. (31.5) 1. (31.5) 1. (31.5) 1. (31.5) 1. (31.5) 1. (31.5) Q Dia ax..5 (.).4 (.0) 1.7 (2.4) 1.27 (32.5) 1.40 (35.7) 1.51 (3.5) 1.64 (41.7) 1.76 (44.) 1. (4.0) *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent.
3Style Series,, onnectors* olarizing ositions D Series 5º R ront face of receptacle (plug opposite). nsert arrangement does not rotate with main keykeyway. The master key is rotated to provide shell polarization; the minor keys remain fixed. ormal D 5º 5º 5º 5º 5º 5º 5º 5º 5º ngle of Rotation (Degrees) 77º 1º 75º 74º 77º 77º 77º 0º 0º 67º 63º 61º 65º 65º 65º 6º 6º 3º 7º º 5º 5º 5º 1º 1º 1º º 5º 1º 1º 1º 1º 0º 0º D Series º R ront face of receptacle (plug opposite). nsert arrangement does not rotate with main keykeyway. The master key is rotated to provide shell polarization; the minor keys remain fixed. D ormal 1 0º 0º 0º 0º 0º 0º 0º 0º 0º ngle of Rotation (Degrees) 2º 6º 0º 7º 2º 2º 2º 5º 5º 72º 6º 66º 70º 70º 70º 74º 74º º 2º 4º 0º 0º 0º 6º 6º º 4º 1º 1º º º º 5º 5º RTL (ront face shown) R S LUG (ront face shown) D S R S KY Series R S KYWY S S DR S S OTS 1. ll ngles are S 2. The insert arrangement does not rotate with main key/keyway 3. ll minor keys are rotated to provide shell polarization, the master key remains fixed at twelve o clock position. 4. olarization is different from Series and. and and and Key & Keyway rrangement identification Letter D D D D Rº or º S 5 2 0 35 64 1 5 1 0 53 51 0 5 4 66 62 7 0 5 4 66 62 7 Key Locations Rº Rº or or º º S S 0 5 2 0 0 5 5 4 1 7 1 6 12 5 5 6 2 6 6 1 2 6 0 0 0 0 0 5 3 7 2 6 0 0 0 0 0 5 3 7 DRº or Dº S 265 3 3 275 304 0 6 2 5 2 2 23 3 4 7 20 272 23 3 4 7 20 272 *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent.
3Style Series,, onnectors* ontact rrangements (ngaging View in nsert) * Socket insert only ** in insert only (ot available in socket insert Series and ) ndicates layouts are available in all shell styles including S274, S2750, KJ2 and KJ5 onsult factory S27505/KJL5 insert availability Series Series Series o. of ontacts Service Ratings 3 # 35 35 35 6 #D 4 4 # 5 5 5 5 # 6 # 7 # 35 #D 3 3 # 4 4** 4 # # Series Series Series o. of ontacts Service Ratings # 35 35 35 #D 5 5 5 5 # #,1 # 1 1 1 1 # # 35 35 35 37 #D 31 42 Series Series Series o. of ontacts Service Ratings 7 7 7 #,4 # 6 6 6 6 # # 26 26 26 26 # 35 35 35 55 #D _ 42 _ 42 # ** #,2 # Series Series Series o. of ontacts Service Ratings 12 2** 26 #,2 # 130 30** 2 #, 1 # 1 # 32 132 32 32 # 35 135 35 66 #D Series Series Series o. of ontacts Service Ratings # # 35 35 35 7 #D 3 3 3 37 #,2 # 41 41 41 41 # Series Series Series o. of ontacts Service Ratings 75 75* 4 # Twinax # 32** 32 # 35 35 0 #D *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent.
3Style Series,, onnectors* ontact rrangements (ngaging View in nsert) * Socket insert only ** in insert only (ot available in socket insert Series and ndicates layouts are available in all shell styles including S274, S2750, KJ2 and KJ5 onsult factory for S27505/KJL5 insert availability *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent.
3Style Series,, onnectors* ontactsin (Series //) L302/5 1st D (WD) 2nd D (RROW) 3rd D (RROW) ontact D 1 olor ands 2 3 Orange lue lack Orange lue Orange Orange lue Yellow Orange lue Green annon 00007 00007 00000 00001 S302 ilitary S302/5360 S302/5363 S302/5364 S302/5365 L302/7 H ontacts (00 ycle) ontact D 1 olor ands 2 3 lue Red lack lue Red rown lue Red Red lue Red Orange annon 000032 000033 000034 000035 S302 ilitary S302/76 S302/76 S302/76 S302/76 ontact oax Twinax oax 5 Ohms 75 Ohms annon 6000 6001 6002 0000 0000 able ccomodations RG RG4,, 3 RG2 /600002 RG4,, 3 ontactssocket (Series ) L302/57 anufacture identification ode rea Typical all contacts KJ ontact D 1 olor ands 2 3 Orange Green Yellow Orange Green Violet Orange Green Gray Orange Green White annon 000074 000075 000076 000077 S302 ilitary S302/57354 S302/57357 S302/5735 S302/5735 ontactssocket (Series & ) L302/56 1st D (WD) 2nd D (RROW) 3rd D (RROW) ontact D 1 olor ands 2 3 Orange Yellow Gray Orange Green rown Orange Green Red Orange Green Orange annon 000070 000071 000072 000073 S302 ilitary S302/5634 S302/56351 S302/56352 S302/56353 L302/6 J ontacts (00 ycle) ontact D 1 olor ands 2 3 lue rown Yellow lue rown Green lue rown lue lue rown Violet annon 00003 00004 00005 00006 S302 ilitary S302/66 S302/66 S302/66 S302/66 ontact oax Twinax oax 5 Ohms 75 Ohms annon 5000 5001 5002 0000 0000 able ccomodations RG RG4,, 3 RG2 /600002 RG4,, 3 *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent.
3Style Series,, onnectors* ontactsrinted ircuit oard RTD RUT OTT XTSO RO RR O OTOR (X / ) OTT RT UR 0307002 0307006 030700 03070 0307006 03070 0307030 03050 03050 OTT SZ D D D D TL D. ±.001 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.062 0.062 S27466 S27467 KJL0 0.261 0.1 0.06 / 0.2 0.4 0.23 0.2 0.6 0.04 0.21 0. 0.364 0. 0.27 0.6 0. 0.046 S27656 S2746 KJL3 / KJL7 0.4 0.6 0.052 / 0. 0.1 0.276 0. 0. 0.01 0.264 0.6 0.347 0.27 0.261 0.3 0.1 0.033 S27505 KJL5 0.40 0.376 0.2 0. 0.363 0.331 0.440 0.40 0.3 0.21 0.42* 0.36* 0.5 0.47 0.4 0.33 0.265 0.3 S27472 S27474 KJ0 / KJ7 0.264 0.6 0.072 0.034 0. 0.11 0.26 0. 0. 0.1 0. 0.6 0.367 0.32 0.21 0.3 0.1 0.03 S274 S2750 KJ2 / KJ5 0.40 0.376 0.2 0. 0.363 0.331 0.440 0.40 0.3 0.21 0.42* 0.36* 0.5 0.47 0.4 0.33 0.265 0.3 S275 S2747 / O S KJ2R / KJ3 / KJ5R 0.264 0.6 0.072 0.034 0. 0.11 0.26 0. 0. 0.1 0. 0.6 0.367 0.32 0.21 0.3 0.1 0.03 D3/Style KJ0 KJ0 0.262 0.0 0.070 0.00 0.7 0.5 0. 0.2 0.7 0.5 0. 0.2 0.365 0.303 0.27 0.7 0. 0.057 D3/Style D3/Style KJ7 () 0.20 0.2 0.0 0.0 0.5 0.1 0.3 0. 0. 0.1 0.300 0.6 0.33 0.3 0.27 0.3 0.7 0.073 KJ7 () 0. 0. 0.066 0.006 0.3 0.3 0.20 0.0 0.3 0.3 0.27 0. 0.361 0.301 0.275 0.5 0.5 0.055 OTT XTSO G (S OT 5) OTT XTSO (KJL0/3/7 & KJ0/7) (KJL5 & KJ0/2/2R/3/5/5R/7) SOKT (SRS ) RTD RUT OTT XTSO RO RR O OTOR (X / ) OTT RT UR 0316006 03160 03160 03160 0340 0307 OTT SZ D D D D TL D. ±.001 0.0 0.0 0.0 0.0 0.0 0.062 S27472 S27474 KJ0 / KJ7 0. 0.1 0. 0.071 0.7 0. 0.262 0.2 0.7 0. 0.1 0.063 S274 S2750 KJ2 / KJ5 0.3 0.21 0.3 0.2 0.361 0.32 0.406 0.374 0.31* 0.35* 0.5 0.3 S275 S2747 / O S KJ2R / KJ3 / KJ5R 0. 0.1 0. 0.071 0.7 0. 0.262 0.2 0.7 0. 0.1 0.063 SOKT (SR & ) RTD RUT OTT XTSO RO RR O OTOR (X / ) OTT RT UR 0370 03703 037040 034040 03 OTT SZ D D D TL D. ±.001 0.0 0.0 0.0 0.0 0.02 S27466 S27467 KJL0 0.4 0.2 0. 0.06 0.43 0.366 0.46 0.4 0.272 0.0 S27656 S2746 KJL3 / KJL7 0.7 0. 0.1 0.03 0.4 0.353 0.46 0.401 0.5 0. S27505 KJL5 0.31* 0.35* 0.3* 0.23* 0.55* 0.553* 0.633 0.601 0.4 0.37 D3/Style KJ0 KJ0 0.5 0.13 0. 0.7 0.43 0.377 0.47 0.4 0.273 0.1 D3/Style D3/Style KJ7 () KJ7 () 0.1 0.11 0.5 0.5 0.435 0.375 0.43 0.4 0.263 0. 0. 0.3 0.457 0.33 0.505 0.441 0.21 0.7 0.26 0. OTS: ULSS OTHRWS SD. 1. OTTS HV GOLD LTG OVR SUTL UDRLT R L302 STO. 2. OTT XTSOS LY TO TT O OTORS OLY OR LL SHLL SZS. 3. / DTS O XTSO. 4. * DTS TL WTH ST XTDG RO RR O OTOR. 5. G D. S.031 +/.0 OR KJL5 D.1 +/.030 (SHLL SZS THRU ) D.00 +/.050 (SHLL SZ ) OR KJ0/2/2R/3/5/5R/7. 6. OR OTHR S OTT DT, OSULT TT, ST,, US. *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent.
3Style Series onnectors* 3Style Series odification odes: Standoff ontacts installed How to Order odification ode 0 1 2 3 4 5 Definition Untinned contacts with extensions & 1 Lead tinned contacts with extensions & 1 Leadfree tinned contacts with extensions & 1 Untinned contacts with extensions & 2 Lead tinned contacts with extensions & 2 Leadfree tinned contacts with extensions & 2 KJ Wall ount with Standoff ontacts installed *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent. 1/2 UTD, LD TD OR LDR TD XU R 1/2 UTD, LD TD OR LDR TD XU R L R. L R. KJ0 WLL OUT KJ7 J UT ontact Style Dimension KJ7T (Jam ut) to.32 /.436 (.6 /.07) KJ0T (Wall ount) to.45 /.503 (.66 /.7) KJ0T (Wall ount) to.4 /.533 (.42 /.54) ontact D Ø ax..02 (.71) Ø in..044 (1.) 1.6 /.671 (.52 /.04).67 /.73 (. / 1.75).70 /.76 (. /.51).036 (.1).052 (1.32) 2.74 /.0 (.02 /.54). /.76 (.72 /.).46 /.06 (.4 /.01).06 (1.73).04 (2.).32 /.436 (.6 /.07).45 /.503 (.66 /.7).4 /.533 (.42 /.54) S 1.6 /.671 (.52 /.04).67 /.73 (. / 1.75).70 /.76 (. /.51) 2.74 /.0 (.02 /.54). /.76 (.72 /.).46 /.06 (.4 /.01 *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent. 26
3Style Series,, onnectors* ontact Sealing ushings Twinax Sealing ushing 335000 Used with the Twinax contact in Twinax layouts for sealing cable size /600002 oax Sealing ushing 334001 Used with the oax contact in Twinax layouts for sealing cable size RG Twinax Grommet oax Grommet (ushing only used with Twinax grommet) ontact Sealing ushing Sequence into Twinax Grommet *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent. 27
3Style Series,, onnectors Wire s and Diameters ontact D * * oax Twinax oax Wire inished wire outside dimensions size (WG) inimum aximum 2, 26,, 0.030 0.054 2, 26, 0.030 0.050 26,, 0.034 0.060,, 0.040 0.03, 1, 0.065 0., 0.07 0.2 RG 0.6 0.6 /600002 0.4 0.4 RG4,, 3 0.04 0.2 *or reference only Recommended Jam ut Torque Values 1 Series nch ounds 46/50 55/60 70/75 0/5 0/5 0/0 0/1 1/0 0/0 Series & nch ounds 30/36 40/46 55/60 70/75 0/5 0/5 0/0 0/1 1/0 oupling ut Torque Values (Series, and ) aximum engagement and disengagement nch ound 1 2 2 32 32 36 36 36 40 inimum disengagement nch ound 2 2 2 2 2 2 4 3 4 3 5 3 6 5 7 5 7 5 *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent. 2
3Style Series, onnectors* ackshell Type (Straight), Series only D. Series 1 Dia. ax..50 (.73).705 (.1).30 (.0).55 (.26) 1.00 (27.32) 1.5 (30.61).330 (33.7) 1.455 (36.6) 1.555 (3.50) Dia. ax..32 (.33).32 (.33).32 (.33).32 (.33).32 (.33).32 (.33).32 (.33).32 (.33).270 (6.6) How To Order inishes Series 1 admium/ickellear 0570776000 0570777000 057077000 057077000 057070000 0570700 0570700 057073000 057074000 admium/ickelo.d 0570600 057063000 057064000 057046000 057047000 05704000 05704000 057050000 0570500 nodic onond. 0570000 0570000 0570000 0570200 0570000 0570000 0570000 057026000 057027000 lectroless ickel 0570776002 0570777002 057077002 057077002 057070002 0570702 0570702 057073002 057074002 ackshell Type (able lamp) Z. D. 1 X X Y Series Series 1 ax. Dia. ax. X Dia. in. X 1 Dia. in. Y ax..50 (.73).5 (3.43).4 (5.4). (4.75).2 (.06).705 (.1). (5.03).27 (7.54). (4.75).1 (.63).30 (.0).3 (7.1).4 (.72).21 (7.) 1.0 (.1).55 (.26).35 (.7).547 (.).3 (.26) 1.1 (2.) 1.00 (27.43).5 (.5).60 (.47).356 (.04) 1.3 (30.56) 1.5 (30.61).635 (.).734 (1.64).456 (.5) 1.46 (37.31) 1.330 (33.7).635 (.).734 (1.64).5 (.1) 1.46 (37.31) 1.455 (36.6).760 (.30). (.42).5 (.1) 1.656 (42.06) 1.555 (3.50). (.57).4 (.).657 (.6) 1.750 (44.45) Z ax.. (.65). (.65). (.65). (.65).33 (.70).33 (.70).33 (.70).33 (.70).3 (.6) How To Order (S Version) S27506 ilitary Designation S27506 Type Straight with able lamp inish ad/ickel (lear) ad/ickel (O.D) ickel (lectroless) Series,,,,,,,, Series,,,,, 1,,, dapter Geometry 2 2 inishes Series Series S annon annon S annon S annon S 27506*2 0573005*** 0 0 0 27506*2 0573006*** 0 0 0 27506*2 0573007*** 0 0 0 27506*2 057300*** 0 0 0 27506*2 057300*** 0 0 0 1 27506*12 05730*** 0 0 0 27506*2 05730*** 0 0 0 27506*2 05730*** 0 0 01 27506*2 05730*** 0 0 0 * S inish *** annon inish *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent. 2
3Style Series onnectors* ackshell Series 504/ 3 S W ilitary Designator Type Straight able lamp 3 0 with able lamp 3 onfiguration Self Locking S onself Locking* *or onself locking, leave designator blank Series,,,,,,,, inish lectroless ickel OD admium over electroless nickel W 504/3 Straight able lamp onself Locking Series ilitary ickel 504/3W 504/3W 504/3W 504/3W 504/3W 504/3W 504/3W 504/3W 504/3W ilitary OD admium 504/3 504/3 504/3 504/3 504/3 504/3 504/3 504/3 504/3 Series Straight able lamp Self Locking ilitary ickel 504/3SW 504/3SW 504/3SW 504/3SW 504/3SW 504/3SW 504/3SW 504/3SW 504/3SW ilitary OD admium 504/3S 504/3S 504/3S 504/3S 504/3S 504/3S 504/3S 504/3S 504/3S 504/3 0 with able lamp onself Locking 0 with able lamp Self Locking Series ilitary ickel 504/3W 504/3W 504/3W 504/3W 504/3W 504/3W 504/3W 504/3W 504/3W ilitary OD admium 504/3 504/3 504/3 504/3 504/3 504/3 504/3 504/3 504/3 Series ilitary ickel 504/3SW 504/3SW 504/3SW 504/3SW 504/3SW 504/3SW 504/3SW 504/3SW 504/3SW ilitary OD admium 504/3S 504/3S 504/3S 504/3S 504/3S 504/3S 504/3S 504/3S 504/3S *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent. 30
3Style Series,, onnectors* ackshell Type (otting oot) D. Series Series 1 Dia. ax..5 (.).7 (1.36).47 (.51).6 (.61) 1.07 (27.61) 1.1 (30.76) 1.336 (33.3) 1.461 (37.) 1.56 (40.2) Dia. ax..434 (.02).54 (.2).673 (.0).7 (.27). (.3) 1.0 (26.01) 1.1 (2.) 1.274 (32.36) 1.3 (35.53) How To Order (S Version) S2746 1 S Designation Series,,,,,,,, Series,,,,, 1,,, 1 Straight up OT: When ordering the S version you must specify both S numbers for the otting oot and the dapter Ring. Series Series 1 S2746 2746**1 2746**1 2746**1 2746**1 2746**1 2746**1 2746**1 2746**1 2746**1 annon 0400000 0400000 04000000 040000 040000 04003000 04004000 04005000 04006000 ** Only even numbered shell size is applicable. otting oot dapter Ring How To Order (S Version) S2745 iltary Designation inish ad/ickel (lear) ad/ickel (O.D) ickel (lectroless) Series,,,,,,,, Series,,,,, 1,,, OT: When ordering the S version you must specify both S numbers for the otting oot and the dapter Ring. Series S2745 2745*** 2745*** 7074*** 2745*** 7075*** 2745*** 7076*** 2745*** 7077*** 1 2745*** 707*** 2745*** 707*** 2745*** 700*** 2745*** 701*** S inish Only even numbered shell size is applicable annon inish Series * ** *** admium/ickel lear inishes admium/ickelo.d lectroless ickel annon annon S annon S annon S 707*** 000 001 002 000 000 000 000 000 000 000 000 001 001 001 001 001 001 001 001 002 002 002 002 002 002 003 003 Wire Sealing lugs Series D Series & D annon S274 olor ode 2000 S2742 lack 20070000 S2742 Red 204000 S2742 Green 205000 S2742 Orange Wire sealing plugs meet S274 standards. The plugs are color coded according to size for easy identification. Wire sealing plugs may be ordered separately. *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent. 31
3Style Series,, onnectors* Tools rimp 2/1 T530 2/1 T565 ontact rimp Tool 2/1 2/1 2/1 2/1 2/1 in ontact Series // Locator or Turret 2/ 2/ 2/4 OR TH 2/4 OR TH 2/4 D or * * oax nner onductor rimp Tool rimp Tool Locator RG 2/1 50006 RG 4,, 3 2/1 50006 RG 2 2/1 50006 oax nner onductor rimp Tool rimp Tool Locator RG4,, 3 2/1 2/4 Twinax rimp Tool rimp Tool Locator enter ontact 2/1 K70 ntermediate ontact 2/501 Y631 Die losure Outer ontact 2/501 Y631 Die losure rimp Tool 2/1 2/1 2/1 2/1 2/1 Socket ontact Series Locator or Turret 2/6 2/6 2/4 2/4 2/4 rimp Tool 2/1 2/1 2/1 2/1 2/1 Socket ontact Series & Locator or Turret 2/7 2/7 2/4 2/4 2/4 Outer onductor rimp Tool rimp Tool Locator RG 2/501 2/53 RG 4,, 3 2/501 2/537 RG 2 2/501 2/5 Outer onductor rimp Tool rimp Tool Locator RG4,, 3 2/31 2/32 * or reference only Tools lastic nsertion/xtraction ontact D * annon Description TD01 TD01 T T03 T TT T oax/twinax oax nsertion tool not required for size annon 274704000 274704000 27470000 27470000 2747003000 37004001 2747003000 6 6/01 6/01 6/ 6/03 6/04 6/04 Superseded ilitary S27534D S27534D S27534 S27534 S27534 527534 nsertion olor Tip Green Green Red lue Yellow Yellow xtraction olor Tip White White Orange White White White Tools etal (S) nsertion xtraction * ontact D OR * * S2745 S2745 S2745 S2745 S2745 and o. 1 indicates tool size. and o. 2 indicates removal tool. or reference only nsertion TT O 50001 5000 5000 500032 olor and lack rown Red lue S2745 S2745 R S2745 R S2745 R S2745 R xtraction TT O 5000 5000 5000 500031 olor and o.1 lack rown Red lue o.2 White White White White *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent. 32
3Style Series,, onnectors* ssembly nstructions Wire Stripping Strip insulation from end of wire to be crimped. (See table for proper stripping dimensions.) Do not cut or damage wire strands. Wire D or *.1 (4.77).1 (4.77).1 (4.77) * or reference only ontact rimping VSUL STO HOL 1. nsert stripped wire into contact crimp pot. Wire must be visible thru inspection hole. 2. Using correct crimp tool and locator, cycle the tool once to be sure the indentors are open. nsert contact and wire into locator. Squeeze tool handles firmly and completely to insure a proper crimp. The tool will not release unless the crimp indentors in the tool head have been fully actuated. ontact nsertion 3. Release crimped contact and wire from tool. e certain the wire is visible thru inspection hole in contact. 1. Remove hardware from plug or receptacle and slip over wire bundle in proper order for reassembly. 2. Using proper plastic or metal insertion tool for corresponding contact, position wire in tip of the tool so that the tool tip butts up against the contact shoulder. 3. ress tool against contact shoulder and, with firm and even pressure, insert wired contact and tool tip into center contact cavity. slight click may be heard as metal retaining tines snap into place behind contact shoulder. ontact xtraction 4. Remove tool and pull back lightly on wire to make sure contact is properly seated. Repeat operation with remainder of contacts to be inserted, beginning with the center cavity and working outward in alternating rows. 5. fter all contacts are inserted, fill any empty cavities with wire sealing plugs, Ressemble plug or receptacle hardware. 1. Remove hardware from plug or receptacle and slide hardware back along wire bundle. 2. Using plastic or metal extraction tool with proper color code corresponding to contact size, place wire in tool. 3. nsert tool into contact cavity until tool tip bottoms against the contact shoulder, expanding clip retaining tines. 4. Hold wire firmly in tool and extract wired contact and tool. Repeat operation for all contacts to be extracted. 5. ill any empty wire cavities with wire sealing plugs, and 6. Reassemble plug or receptacle. *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent. 33
3Style Series,, onnectors* 3Style Specifications The following excerpts are some of the parameter requirements of the LDTL3 Specification. Test Description aragraph Reference ontact Retention 4 5 oupling Torque 4 5 6 Durability 4 5 7 nsulation Resistance 4 5 Vibration 4 5 Shock 4 5 Thermal Shock 4 5 4 ltitude mmersion 4 5 Solvent mmersion 4 5 2 orrosion 4 5 Dynamic Salt Spray 4 5 2 Temperature Durability 4 5 33 Requirements fter preloading to 3 pounds maximum, the force shall be applied at a rate of approximately 1 pound per second and maintained at full load for 5 seconds. o damage to contacts or insert shall result nor shall the contacts be dislocated from their normal position in the connector more than 0.0 inch under the given load. ailure to meet these requirements shall be cause for rejection. ontact * D * 1 Loads in ounds ± % or qualification testing, mating halves shall be coupled and uncoupled, measuring the torques necessary.the torques required to couple and uncouple mating connector halves shall fall within the limits specifications as follows: Torque ax. in. / 2 / 2 2 2 Torque ax. in. 4 3 4 3 Torque ax. in. 1 2 5 2 3 32 6 32 5 Torque ax. in. 36 7 36 5 36 7 40 5 onnector halves shall be mated and unmated 0 times for Series with ground fingers and 500 times for Series and at a rate not exceeding 300 cycles per hour. The test may be performed by hand or by mechanical means, but the coupling ring shall be operated as in normal service. ailure to complete this test because of mechanical malfunction shall be cause for rejection. n insulation resistance test shall be performed on unmated connectors in accordance with LSTD2, ethod 302, Test condition. easurement shall be made between three pairs of adjacent contacts and the shell. ailure to meet the minimum requirement of 50,000 megohms for lasses,,, R, and T shall be cause for rejection. Wired, mated connectors shall be subjected to the vibration test of LSTD2, ethod 4, Test ondition, except that the duration shall be one hour in each plane. Receptacles shall be mounted on the vibration fixture by normal means. ll contacts shall be wired in a series circuit and 0500 millamperes of current shall be allowed to flow through the series circuit during vibration. Suitable means shall be employed to monitor the current flow and to indicate any discontinuity of more than 1 microsecond. The wire bundle shall be damped to the nonvibrating points at least inches from the rear of the connector. urrent discontinuity of 1 microsecond or more, disengagement of the mated connectors, evidence of cracking, breaking, or loosening of parts shall be cause for rejection. Wired mated connectors shall be subjected to one shock in each direction in each of three mutually perpendicular axes. The pulse shall be approximate half sine wave of 300g ± % magnitude with a duration of 3 ± 1 milliseconds. Receptacles shall be mounted on a shock fixture by normal means. ll contacts shall be wired in a series circuit and 00 ma. of current shall flow through the series circuit during shock. Suitable means shall be employed to monitor the current flow and to indicate any discontinuity of more than 1 microsecond. The wire bundle shall be clamped to fixed points at feast inches from the rear of the connector, urrent discontinuity of 1 microsecond or more, disengagement of the mated connectors, evidence of cracking, breaking, or loosening of parts shall be cause for rejection. Unmated receptacles shall be subjected to cycles of thermal shock in the following manner: Step a The receptacle shall be suspended for + 1 0 minutes in the center of a cold water both with a volume of approximately one cubic foot. o dimension of the bath shall be less than inches. The water temperature shall not exceed 4º (3.º) Step b The receptacle shall be suspended for 1 0 minutes in the center of a hot water bath with a volume of approximately one cubic foot. o dimension of the bath shall be less than inches. The water temperature shall be not less than 4º (1º). The time of transfer from one bath to the other shall not exceed 5 seconds. t the end of the tenth cycle, the receptacle shall have the excess moisture shaken off and shall then be dried in a forced air oven at 66±5 for ±1 minutes. ny evidence of damage resulting from this test shall be cause for rejection. ated connectors shall be placed in a container of water at approximately º and placed in an altitude chamber. ll wire ends shall be located within the chamber and exposed to the chamber atmosphere, but not submerged. The exposed wire ends shall not be sealed. quantity of salt, 5 percent by weight, shall be added to make the water conductive. The chamber pressure shall then be reduced to approximately one inch of mercury and maintained for thirty minutes. The chamber pressure shall then be slowly returned to atmospheric. This shall be considered one cycle. Two additional cycles shall be performed. t the end of the last cycle, while the mated connectors are still submerged, the nsulation Resistance Test (room temperature), and the High otential Test (sea level voltages) shall be performed upon the same circuits. ailure to meet an insulation resistance minimum of 2,000 megohms or any evidence of dielectric breakdown or flashover shall be cause for rejection. Unmated connectors shall be immersed fully in the applicable fluid specified below for hours. fter removal from the fluid, each connector shall remain for one hour in free air at room temperature. a.) Jet fuel J4 to LJ56 b.) ircraft lubricating oil to LL6 Unmated connectors and individual contact samples shall be subjected to the soft spray of LSTD2, ethod 1, Test ondition (tin plated, lass Y receptacles hours). mmediately after exposure, the surfaces of the specimens shall be thoroughly washed in tap water and dried in a circulatory oven at a temperature of 3 ±3º (0º) for a period of approximately hours. ny exposure of basis metal as a result of this test, shall be cause for rejection. (Series and, finish ; Series, class W). The wired assembled plugs and receptacles shall be mated and unmated 50 cycles at a rate of 300 cycles per hour maximum. The mating and unmating shall be accomplished so that the plug and receptacle are completely separated during each cycle. The connectors shall then be subjected to the salt spray test in accordance with method 01 of LSTD 44. The connectors shall be tested for 452 hours mated followed by 4 hours unmated. fter the salt spray exposure the remaining number of durability cycles specified in 4.7.7 shall be completed. Wired rated connectors shall be subjected to the indicated anbient temperature for a period of 1,000 hours Series and (finish ) +3º 0 (302º ) 0º Series and (finish ) +3º 5 (347º ) 0º Series (class W) +3º 5 0º (347º ) ll other finishes +3º 0 0º (32º ) * or reference only *DSLR: Our facility is not currently certified by the DL and this product is not covered by the QL/QL. ilspec part numbers are only for cross reference to the ommercial quivalent. 34
roduct Safety and Warranty 1. TRL OTT D HYSL OR lectrical connectors do not usually contain hazardous materials. lectrical connectors and individual components do not release or otherwise result in exposure to hazardous chemicals under normal conditions of use and fall under the definition of rticle, under the Hazard ommunication Standard, 2 R., and are not considered hazardous materials. Solder and fluxes can be hazardous if inhaled or absorbed through the skin and should only be used as recommended by the manufacturer. lease consult your solder and flux manufacturer for more specific application recommendations. 2. R HRTRSTS D LTR SHOK HZRD There is no fire hazard when the connector is correctly wired and used within the specified parameters. ncorrect wiring or assembly of the connector or careless use of metal tools or conductive fluids, or transit damage to any of the component parts may cause electric shock or burns. Live circuits must not be broken by separating mated connectors as this may cause arcing, ionization and burning. Heat dissipation is greater at maximum resistance in a circuit. Hot spots may occur when resistance is raised locally by damage, e.g. cracked or deformed contacts, broken strands of wire. Local overheating may also result from the use of the incorrect application tools or from poor quality soldering or slack screw terminals. Overheating may occur if the ratings in the product Data Sheet/atalog are exceeded and can cause breakdown of insulation and hence electric shock. f heating is allowed to continue it intensifies by further increasing the local resistance through loss of temper of spring contacts, formation of oxide film on contacts and wires and leakage currents through carbonization of insulation and tracking paths. ire can then result in the presence of combustible materials and this may release noxious fumes. Overheating may not be visually apparent. urns may result from touching overheated components. 3. HDLG are must be taken to avoid damage to any component parts of electrical connectors during installation and use. lthough there are normally no sharp edges, care must be taken when handling certain components to avoid injury to fingers. lways wear safety glasses to avoid potential injury to eyes during cleaning, soldering, fiber preparation, etc. lectrical connectors may be damaged in transit to the customers, and damage may result in creation of hazards. roducts should therefore be examined prior to installation/use and rejected if found to be damaged. roper lifting techniques shall be used for handling shipping cartons. 4. DSOSL lease recycle, reclaim or dispose of connectors and individual components in accordance with local, state and federal laws. ncineration of certain materials may release noxious or even toxic fumes.. 5. LTO onnectors with exposed contacts should not be selected for use on the current supply side of an electrical circuit, because an electric shock could result from touching exposed contacts on an unmated connector. Voltages in excess of 30 V ac or 42.5 V dc are potentially hazardous and care should be taken to ensure that such voltages cannot be transmitted in any way to exposed metal parts of the connector body. The connector and wiring should be checked, before making live, to have no damage to metal parts or insulators, no solder blobs, loose strands, conducting lubricants, swarf, or any other undesired conducting particles. ircuit resistance and continuity check should be made to make certain that there are no high resistance joints or spurious conducting paths. lways use the specified application tools, cleaning materials and assembly instructions documented in the Data Sheet/atalog. Do not permit untrained personnel to wire, assemble or tamper with connectors. or operation voltage please see appropriate national regulations. ORTT GRL ORTO (i) ir and creepage paths/operating voltage. The admissible operating voltages depend on the individual applications and the valid national and other applicable safety regulations. or this reason the air and creepage path data are only reference values. Observe reduction of air and creepage paths due to board and/or harnessing. (ii) Temperature ll information given are temperature limits. The operation temperature depends on the individual application. (iii) ressure ll pressure information given are differential pressure limits. The specific differential pressure limits, across the connector interface, are documented in the Data Safety/ catalog (iv) Other important information annon continuously endeavors to improve their products. Therefore, annon products may deviate from the description, technical data and shape as shown in this catalog and data sheets. ommodities in this catalog may be controlled for export or reexport under the xport dministration Regulations (R), uclear Regulatory ommission (R) Regulations, or by the nternational Traffic in rms Regulations (TR) when specifically designed, modified or configured for military use. TT annon manufactures high quality products. However, these products are intended to be used in accordance with the specifications in this publication. ny use or application that deviates from the stated operating specifications is not recommended and may be unsafe. o information and data contained in this publication shall be construed to create any liability on the part of TT. 35
TT annon TT is a focused multiindustrial company that designs and manufactures highly engineered critical components and customized technology solutions. Our customers in the energy, transportation and industrial markets depend on us to solve their most critical problems, and we focus on partnering with them to find solutions to their unique challenges. ounded in, TT is headquartered in White lains,.y., with employees in more than 35 countries. Our connector portfolio remains the most extensive in the industry, offering a reliable and cost effective range of interconnect solutions with the brands of annon, V and W onnector Systems. ontinuous investment in technology and research & development have enabled TT to provide new, innovative products and solutions to markets including: utomotive omputer & onsumer lectronics ndustrial/nstrumentation ilitary & erospace Oil & Gas Telecommunications/Wireless Handheld Devices Transportation When you specify a annon, V or W onnector Systems connector, you can rely on products that are designed, developed, and manufactured to the highest quality and reliability standards. This tradition of excellence is based on TT s corporate culture of operating its businesses under the principles of Six Sigma. t TT, Six Sigma is not just a quality philosophy but a complete corporate culture that drives the entire business. Our Value ased anagement and Value ased roduct Development systems are two cornerstones that allow for the development of both leadership and product engineering principles, ensuring our industry leading products are developed to the accepted market driven lead times. These principles have allowed TT to become the market leader in all of our business portfolios. Six Sigma anufacturing TT annon operates manufacturing facilities in the United States, Germany, taly, exico, hina and Japan, all of which have particular product area strengths allowing TT to offer a truly global footprint to our customers. Our facilities are world class and accommodate full vertical integration utilizing the latest manufacturing technologies including: automated and robotic machining centers, Super arket manufacturing cells, Kanban pull systems, and automated electrical, mechanical, and optical test and inspection equipment. The combination of our manufacturing strength and our advanced manufacturing facilities allows TT to offer products at market driven prices. Our capabilities, especially in robotics, computerized precision tooling, Kaizen roject anagement, Six Sigma tools, and testing, give TT the most optimized global manufacturing footprint in the interconnect industry. The ustom Difference s the industry leader in harsh environment interconnect applications, TT s world class engineering teams will work directly with our customers to design and develop cost effective solutions for their applications. n many cases we may modify one of our standard designs to ensure a highly reliable solution where timing is critical. Yet, in those cases where a complete custom interconnect solution is required, TT will work with our customer s ngineers to design an interconnect solution which will be cost effective yet highly reliable. s professional consultants, our ngineering teams will provide a thorough systems and mechanical analysis of any proposed solution. These analyses provide our customers with sophisticated electrical signal and mechanical characterizations to determine the best solution for their application. RoHS ompliance nformation TT has implemented a strict parts control plan for all TT electronics plants worldwide that allows the annon, V, and W onnector Systems product portfolios to meet the requirements of the uropean Union Directive 02/5/ better known as the Reduction of Hazardous Substances (RoHS) initiative. s appropriate, specific annon, V, and W onnector Systems products may be ordered with an R prefix number which insures our customers will receive RoHS compliant parts for their commercial electronics applications and equipment. Since most RoHS hazardous substances center around specific metal plating and lead solder coatings, TT s products for RoHS compliance are available in the following plating finishes: electroless nickel, stainless steel, anodize over aluminum and gold plating. t should be noted that gold plating would be recommended as the replacement for tinlead solder when ordering board mount connectors. 36
ircular/ilter/hermetic onnectors s a world leader in circular, filter, and hermetic connectors, TT can leverage its design and manufacturing expertise to fit virtually any application. Our expertise includes fast positive mating for a wide range of military applications, as well as numerous sizes and contact configurations for various harsh environments. DSubminiature onnectors annon invented Dsub connectors in 52. Our family of DSubs now includes combinations of signal, power and R, as well as severe service sealed connectors. annon DSubs are available with an extensive line of backshells and accessories and are one of the most economical shielded connector solutions available. iber Optic onnectors and able ssemblies annon fiber optic solutions provide an excellent performance/ cost value. erformance may be tailored to the end system, with our use of superior materials and bonding agents providing highly effective solutions. Our wide variety of products include fiber optic hybrid contacts, multichannel, rack and panel and hirel assemblies. icrominiature onnectors Developed first by annon in the 60s, icrominiature onnectors offer high performance and reliability with exceptional versatility. vailable in rectangular, circular and stripstyle configurations for countless applications, many of our highly engineered icrominiature connector products meet critical customer demands in multiple applications across the erospace & Defense industry. Rack and anel onnectors ioneered by annon during the 30s, our Rack & anel onnectors offer an unmatched variety of shell configurations and insert arrangements, as well as materials, plating and contact options. Today, we are recognized as an industry leader, offering an unparalleled range of offtheshelf and custom Rack & anel products to align with customer needs. R onnectors TT annon has been providing interconnect products to the icrowave and R industry since 63 (formerly The Sealectro orporation). The R 50 & 75 Ohm product lines cover UH band through Ku band requirements. These connectors and cable assemblies are available with a thread type, snap type, bayonet type or slide on coupling method. The frequencies range from D to 1+ GHz. TT annon is a leading global manufacturer of connector products serving international customers in the aerospace and defense, medical, energy, transportation and industrial end markets. Whether delivering critical specs to aircraft pilots, streaming data through communications satellites or enabling ultrasound technology that gives an expectant mother the first glimpse of her unborn child, annon connects the world s most important information with the people who need it. To learn more, visit