SERIES 7000/000 3 PIEE FU PORT B VVES SERIES 7000 Stainless Steel SERIES 000 arbon Steel mm - 0mm 69 bar 0mm - mm 27 bar BRY.O (¼ - 1,000 psi WOG) (6-00 psi WOG) TE IG PERFORNE OPNY
FETURES & BENEFITS FOW-TE S SERIES 7000 N 000 ball valves offer the highest flexibility in selection of end connections, seat materials in a 3 piece design. To meet customer demands for a valve with the widest possible range of applications, these valves can be fitted with control or tri-ported balls (for full cavity drainage), as well as cavity fillers for special service requirements. The Series 7000/000 is designed with extensive interchangeability of balls, stems, stem packing, handles and mounting hardware between valve sizes and series members. This system reduces parts inventory and maintenance costs. The 3 piece body design allows the body to swing-out for ease of in-line maintenance. It also makes it possible to offer a wide variety of end connections. Stem Nut Tab ok Washers Belleville Washers Packing Gland Peek Protector Stem Packing Tek-Fil Thrust Washer PEE Protector nti-static evices NE Flow-Tek handles feature a standard Safety Trigger to prevent accidental movement of ball position. Operation is easily made with one hand. The trigger locks the handle in the open or closed position. The handle lock can be bypassed, if needed, with a small bolt through the handle in the bypass position. n nti- Tamper Padlock can be used to secure the handle in position, preventing unwanted access. Travel stops limit the movement of handle to set intervals, preventing over travel of the ball. 9 EN ONNETIONS Full range of interchangeable connections including threaded, socket weld, butt weld, SE lass 0 flanged and extended weld in place. SRT STE mm to 65mm (¼ to 2½ ) Flow-Tek s interchangeable family of valves feature strong large diameter stems with live-loaded, selfadjusting stem seal utilising Belleville washers which automatically adjust to compensate for changes in temperature and wear. The assembly is secured by a saddle-type tab lock washer which prevents stem nuts from unthreading in high cycle automation applications. STE SSEBIES Flow-Tek manufactures heavy duty, high quality stems with double connection to ball and operator mounting. Stems are mated with the ball to ensure positive contact. ll Flow- Tek stems are internal entry and blowout proof for maximum safety. 65mm, 0mm, 0mm (2½, 3 and ) valves feature a NUR stem slot for ease of limit switch mounting. STE PING n adjustable V-ring design creates a multiple seal between the stem and body. Each stem assembly is composed of three or four (dependent on valve size) rings providing a very high cycle life by resisting creep and cold flow. The Thrust Washer and the Thrust Washer Protector combine to provide a primary seal, reduce torque and prevent galling. 13 NTI-STTI PROTETION Series 7000/000 valves feature anti-static grounding devices as standard. These devices ensure electrical continuity between valve ball, stem and body, thus eliminating the possibility of static electrical charges creating sparks within the valve. STE ESIGN 0mm - mm (3 ) The stem is guided by the valve body and the gland, ensuring smooth operation even in high torque service. The packing gland is adjustable and all stems are polished to reduce torque. Optional Belleville washers can be added for a self-adjusting, live loaded stem packing assembly. FETURES & BENEFITS 1 B Flow-Tek balls are solid metal, precision machined and mirror finished for bubble-tight shut off with less operating torque. Ball edges have machined curvatures to reduce wear and provide high cycle life. 2 BOY Valve bodies are investment cast and solution annealed/normalised for the highest quality and added strength. Body castings are marked with a foundry heat number for full traceability. arbon steel bodies are phosphate coated for increased corrosion resistance. 3 SET Flow-Tek s seat design ensures bidirectional, bubble-tight sealing while providing the lowest possible torque. This seat design reduces friction, minimises seat wear and reduces operating torque. SET TERIS Flow-Tek offers the following standard seat materials for the Series 7000/000: RPTFE, TF-1600, Stainless Steel/PTFE (/), UWPE, Virgin PTFE, Tek-Fil, and avity Fillers. Other seat materials are available. 5 OUBE O NUT ESIGN Standard on the Series 7000/000, the double lock nuts allow handles to be easily and safely removed while the valve is under full line pressure. 6 IVE-OE STE SES The standard (up to 65mm; up to 2½ ) live-loaded stem seals with Belleville washers considerably increase the number of cycles between maintenance adjustments. 7 SEURE OUNT The integrally cast top flange ensures positive actuator mounting. Secure ount eliminates unwanted actuator movement during high cycle or continuous duty applications. ctuation equipment can be easily and safely removed while the valve is under full line pressure. esigned to ISO 52 bolting pattern standards. PRESSURE/TEPERTURE Pressure [psi] 00 0 00 700 600 0 00 0 Temperature ( ) [ ] 0 0 0 0 3 0 0 00 0 600 700 Temperature ( F) [ F] Note: Series 7000 stainless steel valves are limited to -5 ( F) Series 000 carbon steel valves are limited to -29 ( F). 70 60 0 30 Pressure (bar) [bar] PRESSURE RTINGS Threaded, Socket Weld and Butt Weld: SIZES: mm - 0mm (¼ ) 0mm - mm (6 ) Flanged: SE B16.3 lass 0 Steam Rating: Vacuum Rating: TF: bar (0 psi WSP) Tek-Fil: 29 bar ( WSP) 1,01 bar (29.9 in. g gauge) egend: > UWPE: mm - 0mm (¼ - ) > RPTFE/TF: mm - 0mm (¼ - ) > / SS Filled TFE: mm - 0mm (¼ - ) > Tek-Fil: mm - 0mm (¼ - ) > RPTFE: 0mm - mm (6 - ) Butt Weld > SE lass 0 Flanged WOG: 00 psi 00 psi 2 BRY ONTT T. + 1 59 BU.SES@BRY.O SERIES 7000/000 3 PIEE FU PORT BRY.O 3
TERIS OF ONSTRUTION SPEI OPTIONS/SERVIES EXPOE VIEW 65 ( 1 21 2 ) > avity Fillers > eadman andles > Vented Balls > Polished Internals > Special leaning > Silicone Free > hlorine Service Optional avity Fillers 2 OPONENTS N TERIS 65 ( 1 21 2 ) ITE ESRIPTION STINESS STEE RBON STEE QTY 1 Body ST 351 Gr F ST 216 Gr WB 1 2 End ap 1 ST 351 Gr F 1 ST 216 Gr WB 2 29 3 Ball ST 351 Gr F 1 Seat % RPTFE 2 2 5 Stem ST 79 Type 316 1 1 6 Body Seal TF 2 2 7 Spring ock Washer SS30 Body Nut SS30 9 Body Bolt / Stud SS30 nti-static evice (not shown) SS316 2 Thrust Washer/Packing Protector PEE 2 2 Thrust Washer TE-FI 1 2 Stem Packing % RPTFE 3 2 Packing Gland Sleeve SS30 1 1 Belleville Washer SS301 2 0 05 2 23 09 0 01 Tab ock Washer SS30 1 23 Travel Stop Set Sleeve SS30 1 2 Travel Stop Bolt SS30 1 andle SS30 1 Extended Butt Weld End onnection Stem Nut SS30 2 2 andle Sleeve Vinyl 1 29 ocking evice SS30 1 1) Weld Ends use F3 2) Recommended spare parts that are available as a packaged repair kit ) Number of Nuts and Spring Washers: mm mm (¼ 2 ) valves ; 65mm (2½ ) valves 0 03 07 Socket Weld End onnection Note: Other End ap connections are available. BRY ONTT T. + 1 59 BU.SES@BRY.O SERIES 7000/000 3 PIEE FU PORT BRY.O 5
TERIS OF ONSTRUTION SPEIFITION EXPOE VIEW 0mm mm (3 ) Valve Sizes mm mm (¼ ) esign SS-SP-0 *NUBER OF BOY BOTS Threaded End onnection SE B1..1 NPT. Socket Weld End onnection SE B16. Butt Weld End (sch 0) onnections SS SP-72 /SE B16. SIZE 65mm, 0mm 3, QTY mm and mm (" and ") Flanged End onnections SE lass 0 Valve body and end cap connections are high quality investment cast and solution annealed/normalised. Body and end cap wall thickness meets SE B16.3 Valve stems are blow-out proof for maximum safety and meet SE B16.3 specification ll valves are factory tested to SS SP-72 and PI 59 0mm 6 mm 0mm mm 2 0 17 B 16 27 22 OPONENTS N TERIS 0mm mm (3 ) ITE ESRIPTION STINESS STEE RBON STEE QTY 1 Body ST 351 Gr F ST 216 Gr WB 1 13 21 2 End ap 1 ST 351 Gr F 1 ST 216 Gr WB 2 3 Ball ST 351 Gr F 1 Seat % RPTFE 2 2 B Seat Support ST 351 Gr F ST 216 Gr WB 2 5 Stem ST 79 Type 316 1 6 Body Seal PTFE 2 2 9 Body Bolt SS30 * nti-static evice (not shown) SS316 2 B 05 09 B Thrust Washer/Packing Protector PEE 2 2 01 Thrust Washer TE-FI 1 2 09 13 Stem Bearing % RPTFE 1 2 Stem Packing % RPTFE 2 Packing Gland SS30 arbon Steel 1 16 Packing Follower ST 351 Gr F ST 216 Gr WB 1 17 Gland Bolt SS30 arbon Steel 2 03 0mm 0mm (3" 6") Stop ousing ST 351 Gr F ST 216 Gr WB 1 21 ousing Bolt SS30 arbon Steel 22 Travel Stop SS30 arbon Steel, Zinc Plated 1 andle uctile Iron/arbon Steel 1 B andle unction uctile Iron 1 27 andle Bolt arbon Steel 2 30 Snap Ring (not shown) Nickel Plated arbon Steel 1 27 1) Weld Ends use F3 2) Recommended spare parts that are available as a packaged repair it ) Seat Supports for 0mm (6 ) and larger valves ) 3 or rings depending on valve size 6 BRY ONTT T. + 1 59 BU.SES@BRY.O SERIES 7000/000 3 PIEE FU PORT BRY.O 7
Ux Ux Ux Ux IENSIONS TENI TSEET Secure¼ ount: - 2 ½ VVES Secure ount: - 2 ½ ¼ VVES Secure3 ount: 3 - VVES Secure ount: - VVES IENSIONS Flow-Tek s 3 piece valve is offered with a center body and a large selection of end connections. This versatile design offers easy customising to meet most special application requirements. 65mm ¼ mm - 2 ½ VVES 1/" 21/2" 0mm 0mm 3 - VVES 3" " øe1 øf2 øe2 øf2 øe2 N x øt N x øt øf3 øs øe3 øf3 øs øe3 SOET WE EN 7/ S 0 BUTT WE EN 7/ FNGE EN 700/00 øe1 TREE EN 70/0 0mm mm 6 - VVES 6" " Ux 1 1 1 Ux øf5 øe1 øf5 øe1 øf2 øe2 øf2 øe2 SEURE Secure ount: ¼ -OUNT 2 ½ VVES mm 65mm 1/" 21/2" SEURE Secure ount: 3 OUNT - VVES S. 0 EXTENE BUTT WE EN 73E00/3E00 EXTENE SOET WE EN 72E00/2E00 0mm mm 3" " Extended End connections may be fabricated from pipe and fittings. IENSIONS [mm] N x øt SIZE NPT, SW, BW Extended Extended FG SW BW øe1 1,5 5 1 9,5 39,7 39,9 229,5 7,2, 236,2 1,7 271,9 20,7, øf2 øe2 P øf3 øs øe3 UN U 6, -2 29.7 6, -2 39 29.7 6, -2 7 2,1 6, -2 7 52,9 1/-,9 1/- 56 1 3 5 0 9,5 9,5 23 9,5,7 5/16-1 0 9,5 øf2 øe2 0 9,5 23 9,5,7 5/16-1 17,5 29 5/16-1 0 2, 29, 0 3 299,2 2 65,5 0 229,6 317 øf5 øe1 272,6, 5 75 30, 65 6 2 6,5 30, 76 163 9,5 3 7,6,5 7 17 2 0 230 353 30, 1 0,5 3 7,6,5 7 17 2 0 57,2 39 2 3 00 5,7 5,7 2 3,5 5,7 57 33 2 00 5,7 5,7 2 3,5 0 55, 533 0 373 3 00 5 5 96 35 55 5/- 635 6 13 293 00 5 5 96 35 55 5/- Note: Flanged Face-Face dimension on sizes mm 0mm (1/2" ") are manufacturer s standard; 0mm mm (5 ) meet SE B16. long pattern BRY ONTT T. + 1 59 BU.SES@BRY.O VVE IENSIONS [mm] Nm kg SIZE E1 E2 E3 F2 F3 F5 N S T v Torque Weight 9, 13,7 22,,7 6, 0, 17,5,5 17,2 22,,7 6, 0, 21,7,. 2 21,3,9 29 22,,7 2,5 1,2 60,5,6 6, 0, 27,1,93 35,7 9,6 37,9,3 57 5, 69,9,6 5,7 1,1 33,,6 2 33, 7 5 27,1,9 57 7,1 7,6 5, 1,5 2,6 35,1 52 2,2 55 31,6 17,5 9 22 2,2 0,6 0,9 3 60,3 7 62,5 73 1,6 9,6,6 275 35,6 3.5 61,1 52,5, 7 60,3 2, 7 36,2 22,2 0 3,7 1,7 0 57,6 5,2 65 73, 62,5 6 73 9,5 70, 9,9 0 9, 76 76 1 1,5 77,3 2, 1,,3.7 0 5, 1 135 1,5 22,6 53 30 1,5 1,5 2,1,7 2, 0,1 2 16,3 279, 3,6 21,3 22, 5 69 1 2,7 2,9 1,9 1 29,5 22, 9,6 700,5 171 0,5 0 273,1, 1, 2,5 362, 1,1 27 303,2 3,6 2,6 130,5 31,, 21 2,6 F Note: mm 0mm (¼" ") weights are based on threaded end connection. 0mm mm (6" ") weights are based on lass 0 flanged ends. Torque values are at maximum rated pressures, clean water, RPTFE seats. Refer to Tech Bulletin 05 for complete torque information. SERIES 7000/000 3 PIEE FU PORT For am ock, Tube O. (Outside iameter). and Flush Bottom Tank connection dimensions and for other available End onnections, please consult the Flow-Tek factory. End connections are fully interchangeable and can be used in any combination. BRY.O 9
3-PIEE ESIGN 3 PIEE VVE BOY ESIGN 3 PIEE WE IN PE SERIES SOET-WE N BUTT-WE The unique body design of the Series 7000/000 offers many advantages, including installation flexibility, and ease of in line and out of line servicing. These time saving features are a big plus for process industries, automated valves and welded piping systems by reducing costly downtime. eavy duty hinges, throughout the entire size range, provide positive alignment of body to end connection during swing-out, in-line servicing. uring maintenance, the actuator and mounting assemblies remain on the valve body. The entire valve and actuator assembly is easily reinstalled. No actuator adjustment or reattachment is necessary. Flow-Tek offers extended end connections for the Series 7000/000 valves. These ends allow the customer to weld the valve in the piping system without valve and/ or actuator disassembly possibly damaging the seat or seals. Installation time and piping material is reduced. dditionally, the Weld In Place Series extended end connections limit potential installation errors. The valve is factory assembled and tested, then delivered to the customer for installation. IN INE SERVIING OUT OF INE SERVIING > To perform in line maintenance, remove one of the body bolts through one of the two body hinges, loosen the remaining bolts and swing the body up. The valve can swing to the left or right depending on which bolt is removed. ll body components can be serviced in this position without disturbing the pipe system. > For complete removal of valve from the line, remove the upper two bolts that go through the body hinges, loosen the lower two while keeping them in line, then lift the valve body out of the pipeline. The remaining two bolts help to keep the pipeline system in place and maintain alignment. The removed body can then be serviced and/or replaced. OWNO Please visit our website for our extensive product range, brochures, manuals and others supporting documents bray.com BRY ONTT T. + 1 59 BU.SES@BRY.O SERIES 7000/000 3 PIEE FU PORT BRY.O
TE IG PERFORNE OPNY O BRY ONTROS (U) IITE Subsidiary of Bray International, Inc. 16-1 Fountain rescent Inchinnan Business Park Inchinnan P 9RE Scotland T. + 1 59 F. + 1 69 bcuk.sales@bray.com www.bray.com BRY INTERNTION PRIRY SES N SERVIE OTIONS FRI ohannesburg IN angzhou, Zhejiang EXIO Zapopan, alisco SOUT ORE Seoul USTRI elbourne OOBI Bogotá IE EST ubai SOUTEST SI alaysia BENEUX eerhugowaard FRNE Voiron PERU ima UNITE INGO Glasgow BRZI Paulinia, Sao Paulo GERNY refeld PON Oświęcim US ouston, Texas N ontreal INI Vadodara RUSSI oscow IE Santiago ITY ilano SINGPORE Ubi Techpark FOW-TE RITE ORPORTION RESIST UGEN ÜER BRZI Paulinia, Sao Paulo N ontreal US ouston, Texas GERNY refeld IN angzhou, Zhejiang VVTRONI BRY/VS US ouston, Texas RGENTIN Buenos ires INI hennai ll statements, technical information, and recommendations in this bulletin are for general use only. Please contact us for the specific requirements and material selection for your intended application. The right to change or modify product design or product without prior notice is reserved. Patents issued and applied for worldwide. Bray is a registered trademark of Bray International, Inc. 17 Bray International. ll rights reserved. B-FT-2301_S7kk_EU-EN_17-0-30 EQURTERS BRY INTERNTION, IN. 13333 Westland East Blvd. ouston, Texas 7701 T. +1 21.9.55