ILLUSTRATED PARTS LIST MFG. ID NO. 96051005000 CUSTOMER CATALOG NO. M15-9HRB PRODUCT NO. 960 51 00-50 53 44-19 Rev. 8
MAX +_90N MAX +_150N TRACTOR - - MODEL NO. M15-9HRB (96051005000), PRODUCT NO. 960 51 00-50 DECALS 14 14 5 8 10 1 3 6 0 53 19 68-41 Decal Warning Eng. Sym. 3 53 18 8- Decal Deck Enviro. 5 53 43 9-66 Decal Wheel Steering 6 53 18 04-3 Decal 100 DBA 53 44-0 Decal Side Panel 8 53 44 55-03 Decal Warning TCRD 10 53 43 8-5 Deck Hood Predator RH/LH Set 53 18 1-66 Decal Mower Cut Finger Symbol 14 53 15 9-36 Decal Chassis Hot Muffler 0 53 44 09-01 Decal Bypass Fender CRD 1 53 44-89 Decal Belt Sch CRD - - 53 4 59-8 Pad Footrest RH - - 53 4 59-6 Pad Footrest LH - - 53 44-14 Manual Operator's (Euro) - - 53 44-15 Manual Operator's (Scan) - - 53 44-16 Manual Operator's (E-Bloc) - - 53 44-1 Manual Operator's (Baltic) WHEELS & TIRES 1 5,8 6 4,10 3,9 1 53 05 91-9 Cap Valve Tire 53 06 51-39 Stem Valve 3 53 10 6- Tire F Ts 15 x 6 0-6 Service 4 53 05 99-04 Tube Inner Front #35060 5 53 1 51-51 Rim Asm 6" Front Silver Service 6 53 1 49-5 Fitting Grease 53 1 49-59 Bearing Flange 8 53 1 51- Rim Asm 8" Rear Silver Service 9 53 4 05-31 Tire R.Ts-LT 18 x 9.5-8 C Ser. 10 53 1 49-6 Tube Rear 9 5 x 8 Service 53 1 50-39 Cap Axle Blk 1 50 x 1 00 - - 53 14 43-34 Sealant, Tire (10 oz. Tube) wheel_1 NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm
SCHEMATIC 38 SCH1 FUSE RED BATTERY 8 RED C1 SOLENOID RED STARTER M WHITE WHITE S B M A1 G L A BLK/WHT BLUE RED GREEN WHITE C1 5 6 CLUTCH/BRAKE (PEDAL UP) GRAY ATTACHMENT CLUTCH (CLUTCH OFF) REVERSE SWITCH (NOT IN REVERSE) BLK/WHT GREEN YELLOW YELLOW SEAT SWITCH (NOT OCCUPIED) 3 1 GREEN 6 GRAY 9 C1 BAG FULL SWITCH (NOT FULL) SHORTING CONNECTOR BAG PRESENT SWITCH (BAG ATTACHED) NOTE YOUR TRACTOR IS EQUIPPED WITH A SPECIAL ALTERNATOR SYSTEM. THE LIGHTS ARE NOT CONNECTED TO THE BATTERY, BUT HAVE THEIR OWN ELECTRICAL SOURCE. BECAUSE OF THIS, THE BRIGHTNESS OF THE LIGHTS WILL CHANGE WITH ENGINE SPEED. AT IDLE THE LIGHTS WILL DIM. AS THE ENGINE SPEED IS INCREASED, THE LIGHTS WILL BECOME THEIR BRIGHTEST. /WHITE BLUE FULL BAG BUZZER BLUE FUEL LINE FUEL SHUT-OFF SOLENOID (IF SO EQUIPPED) BLUE IGNITION UNIT (OPTIONAL) HOUR METER CHARGING SYSTEM OUTPUT 3 AMP DC @ 3600 RPM SPARK PLUGS GAP ( PLUGS ON TWIN CYL. ENGINES) BLUE 1V POWER OUTLET (OPTIONAL) 8 VOLTS AC MIN. @ 3600 RPM (CHARGING SYSTEM DISCONNECTED) LIGHT SWITCH BROWN LIGHTING SYSTEM OUTPUT 5 AMP AC @ 3600 RPM ALTERNATOR DIODE ORANGE 14 VOLTS AC MIN. @ 3600 RPM (LIGHTS OFF) 4 BROWN C1 IGNITION SWITCH HEADLIGHTS POSITION CIRCUIT OFF M+G+A1 RUN/OVERRIDE B+A1 RUN B+A1 START B+S+A1 MAKE L+A 1 3 4 5 6 8 9 CHASSIS HARNESS CONNECTOR (C1) (MATING SIDE) 3 1 6 5 4 9 8 DASH HARNESS CONNECTOR (C1) (MATING SIDE) WIRING INSULATED CLIPS NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR SERVICING OF UNIT, THEY SHOULD BE RE-INSTALLED TO PROPERLY SECURE YOUR WIRING. NON-REMOVABLE CONNECTIONS REMOVABLE CONNECTIONS 3
ELECTRICAL 3 TC03S With Service Minder Option 9 1 30 33 34 46 18 8 With Charge Indicator Option 14 6 143 40 (+) (-) 16 1 10 105 9 41 43 8 55 108 5 10 83 4
ELECTRICAL 3 1 53 43 1-5 Battery 53 44 09-3 Screw Hex Hd Cap M6 x 1.1mm 16 53 1 61-38 Switch Interlock 1 53 40 0-5 Harness Asm Light w/415j 53 00 41-5 Bulb Light #56 5 53 43 1-6 Cable Battery 4" 8 AWG Red 6 53 1 51-58 Fuse 83 51 04-00 Nut Keps Hex 1/4-0 unc 8 53 43 1-63 Cable Ground 8 AWG 18" Black 9 53 40 15-45 Switch Seat 30 53 19 33-50 Switch Ignition 33 53 41 19-35 Key/Chain 34 53 0-1 Switch Light 40 53 4 10-0 Harness Ignition 43 53 19 5-0 Solenoid 55 81 06 05-1 Screw 5/16-18 x 3/4 1 53 44 08-0 Harness Chassis 9 53 1 5-4 Socket Asm. 83 53 43 6-4 Nut Square M6 x 1 x 8.5 x mm 8 53 4 10-60 Switch Railmount 99 81 04-08 Screw 1/4-0 x 1/ 10 53 40 44-54 Harness Reverse 105 53 40 5-68 Switch Reverse 10 53 18 03-9 Switch Full Bagger Indicator 108 53 4 10-6 Switch Snapmount NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm 5
CHASSIS AND ENCLOSURES 39 9 153 14 18 130 3 191 5 16 5 3 16 150 16 1 18 159 83 199 8 84 36 194 68 36 194 16 36 15 35 130 68 130 35 34 130 151 13 310 68 18 319 16 8 8 16 8 3 183 68 183 36 180 343 68 68 309 3 159 8 189 34 156 194 189 1 308 19 156 5 340 338 8 341 chassis-tex crd_tex LT PRED_8 19 339 34 15 189 189 6
CHASSIS AND ENCLOSURES 39 5 53 40 95-9 Dash 14 53 40 95-98 Hood 18 53 4 65- Grille 34 53 44-53 Plate Engine 36 81 06 05-1 Screw 5/16-18 x 3/4 3 53 43 96-4 Fender 5 83 68 05-00 Nut Crown Lock 5/16 68 81 49 05-08 Screw Thdrol. 5/16-18 x 1/ 130 53 41 63-58 Screw #10 x 0.50 BOS Thread 150 53 40 89-56 Air Duct 151 53 18 5-68 Bracket Pivot Hood 15 53 19 95-35 Shield Browning 153 53 44 4-64 Lens 156 8 14 06-14 Bolt 3/8-16 unc x 1-3/4 159 81 00 06-1 Screw Kexwsh Thdr 3/8-16 x 3/4 16 53 14 4-3 Screw Hex Wsh. Hi-Lo 1/4 x 1/ unc 53 44 1-89 Extension Bagger Full 15 53 19 94- Crossmember 16 53 40 0-6 Screw 10-4 x 5/8 1 53 19 5-8 Bushing Steering 19 53 16 89-3 Nut Push 180 53 43 54- Chassis 18 53 40 1-6 Dash Lower 183 84 5 05-0 Bolt 5/16-18 x 1-1/4 189 81 00 05-1 Screw 5/16-18 x 3/4 191 53 41 65-0 Insert Reflective RH 194 83 90 05-00 Nut Lock Hex Flange 5/16-18 199 53 41 8-39 Plate Deck Lift 13 84 6 05-1 Bolt 5/16-18 x 3/4 1 53 40 91-6 Rod Pivot Hood 18 53 19 63-95 X-Piece Hood Stop 5 53 44 58-5 Bumper Grille 8 53 19 51-61 Stud Fastener 35 53 40 61-9 Spacer Fender 36 83 93 05-00 Nut Lock 5/16-18 unc 3 53 40 3-04 Plug Mount Cargo 8 53 41 41-10 Clip Retainer 83 53 44 03-61 Console Deck Lift 84 53 44 1-9 Console Shift 8 81 60 04-06 Screw Hex Washead 1/4-0 x 3/8 9 53 40 18- Insert Reflective LH 308 53 1 18- Bolt 5/16-18 unc x 3/4 309 53 43 66-6 Backplate Bagger 310 53 44 66-36 Bracket Hangar Bag LH 3 53 44 66-3 Bracket Hangar Bag RH 319 53 1 46-6 Bracket Actuator 338 53 43 66-40 Bolt Shoulder 339 53 44 1-88 Lever Bagger Full 340 53 44 09-31 Door Battery Tray 341 53 43 66-38 Latch Battery Door 34 53 43 59-38 Support Fender 343 53 44 0-49 Clip NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm
DRIVE 40 56 315 68 63 5 335 185 143 80 36 50 315 335 315 364 6 351 354 315 50 103 184 1 35 353 38 33 161 195 15 15 6 143 339 355 6 339 35 15 63 15 15 4 64 160 03 16 159 186 49 3 15 165 189 90 314 333 330 331 348 188 99 166 50 51 5 14 141 140 16 313 354 33 183 05 3 3 319 * 61 30 1 319 9 6 15 159 38 15 360 360 360 356 3 31 140 313 1 3 183 3 05 9 309 143 3 33 drive-tex CRD_K46_fender_1_r1 8
DRIVE 40 1 Transaxle, Tufftorq K46DC (43639) (Order parts from transaxle manufacturer.) 53 1 35-83 Key Square 6 53 1 40-8 Bushing Snap 15 819 13 13-16 Washer 13/3 x 13/16 x 16 Ga. 1 53 43 6- Spring, Brake 53 44 3-46 Rod Shift 3 53 10 69-33 Knob 9 53 43 58-81 Rod, Brake 33 81 00 00-01 Ring E 35 53 40 10-31 Rod, Brake, Park 3 53 1 1-49 Washer 38 53 16 96-13 Nyliner Snap In 4 53 1 48- Cover, Foot Pedal 49 8 06-14 Bolt 3/8-16 x 1-3/4 Gr. 5 50 53 43 68-1 Pulley Idler Flat 51 83 90 06-00 Lock Nut 3/8-16 5 53 19 43-6 Idler V-Groove 56 53 44 18-34 V-Belt, Drive 61 53 43-88 Pulley Transaxle 64 53 19 6-00 Shaft Asm. Pedal Brake Control 3 84 49 05-56 Bolt Hex 5/16-18 x -1/ G5 90 53 44 36-05 Keeper Belt Clutching 99 53 44 39-4 Rod Spring Bypass 103 83 35 05-00 Nut Hex Jam 5/16-18 unc 6 83 90 05-00 Nut Lock Hex Flange 5/16-18 15 81 00 05-1 Screw 5/16-18 x 3/4 16 53 16 60-0 Washer Srrtd. 5/16 ID x 1 x.15 140 810 04 04-00 Washer Lock 1/4 141 819 09 1-10 Washer 9/3 x 3/4 x 10 Ga. 143 81 49 05-08 Screw Thdrol 5/16-18 x 1/ 159 86 0 04-1 Pin Cotter 1/8 x 3/4 160 53 16 94-84 Retainer Clip 161 53 10 5-09 Spring, Return, Clutch 165 53 19 6-1 Nyliner 166 53 4 91-64 Nut Push.65 16 53 40 5-5 Latch Brake Parking 14 53 19-89 Nut Push 15 53 44 18-3 Shaft Asm Shift 183 53 13 0-5 Spacer Axle 184 53 44 14-0 Handle Parking Brake 185 8 06- Bolt 3/8 x -3/4 Gr. 5 186 53 19 43-1 Spacer Retainer 188 53 19 43-3 Link Clutch Ground Drive 189 53 43 36- Bellcrank Ground Drive 195 53 43 58-65 Bracket Rod Brake 03 819-16 Washer /3 x /16 x 16 Ga. 05 53 1 1-48 Washer 5/3 x 1-5/8 x 16 Ga. 1 53 40 31-8 Retainer Spring 6 53 40 15-64 Bracket Mount Torque 81 49 05-1 Screw Thdrol 5/16-18 x 3/4 63 81 00 06-1 Screw Thdr 3/8-16 x 3/4 68 53 18 4-0 Guard Muffler 5 819 13 16-14 Washer 13/3 x 1 x 14 Ga. 9 53 44 4-83 Sub Asm Link 80 819 10-1 Washer /3 x 5/8 x 1 Ga. 309 53 16 55-81 Plate Fstnr. Cross 3 53 16 98-45 Washer Nylon 31 53 16 56-14 Hub Tapered 313 84 8 04-16 Bolt Hex Fin 1/4-0 unc x 1 Gr. 5 314 53 44 4-13 Belt Keeper 315 81 58 05-0 Screw Thdrol 5/16-18 x 1.5 319 53 43 6-94 Spacer Transaxle 30 53 18 6-90 Washer Spacer 38 53 43 5-58 Shaft Shift Front 330 53 16 95-93 Washer Nyliner 331 53 44 36-06 Hub Shift 333 53 1 08-68 Washer Spring Wave 335 53 19 95-34 Idler V Pulley Grnd. Dr. 33 53 43 59-3 Bracket Support Shift 339 53 43 68-6 Strap Torque 348 53 44 36-0 Arm Clevis 351 53 43 69-98 Bracket Deck Sway 35 53 43 58-19 Bracket Idler 353 53 43 65- Bracket Idler RH 354 81 49 05-10 Screw 5/16-18 x 5/8 355 53 43 56-69 Strap Torque 356 53 43 64-64 Link Shift Cross Shaft 360 53 44 4-14 Nut 36 53 43 68-1 Idler Flat 364 53 44 30-3 Bracket V-Idler * Parts supplied by manufacturer NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm 9
ENGINE 4 1 1 0 45 84 1 9 18 9 15 96 1 69 3 8 3 4 9 90 85 9 OPTIONAL EQUIPMENT Spark Arrester engine-tex_bs_35 10
ENGINE 4 1 Engine Briggs Model 1980-340-B1 (438614) (Order parts from engine manufacturer.) 53 1 9-58 Muffler 9 53 19 43-0 Keeper Belt Engine 1 53 40 54-1 Pulley Engine 15 53 40 5-45 Tank Fuel 18 53 43 0-0 Cap Fuel 0 53 41 1-4 Control Throttle 1 53 41 63-58 Screw #10 x 0.50 53 41 1-5 Control Choke 8 53 13 0-40 Line Fuel 9 53 13 1-80 Kit Spark Arrester (Flat Scrn) 3 53 1 34-8 Clamp Hose Blk 4 810 04 0-00 Washer Lock /16 45 83 51-04-00 Nut Keps Hex 1/4-0 unc 69 53 16 5-91 Gasket Muffler 9 53 19 3-34 Screw 5/16-18 x.5 84 81 06 06-0 Screw 3/8-16 x 1-1/4 85 53 1 39-3 Bolt /16-0 x 4 x Gr. 5-1.5 THR 90 81 00 06-16 Screw 3/8-16 x 1 96 819 09 14-16 Washer 9/3 x /8 x 16 Ga. 9 81 6 04-1 Screw Hexwsh Thdrol 1/4-0 x 3/4 1 53 4 19- Extension Drain Oil NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm Engine Power Rating Information The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of Automotive Engineers) code J1940 (Small Engine Power & Torque Rating Procedure), and rating performance has been obtained and corrected in accordance with SAE J1995 (Revision 00-05). Torque values are derived at 3060 RPM; horsepower values are derived at 3600 RPM. Actual gross engine power will be lower and is affected by, among other things, ambient operating conditions and engine-to-engine variability. Given both the wide array of products on which engines are placed and the variety of environmental issues applicable to operating the equipment, the gas engine will not develop the rated gross power when used in a given piece of power equipment (actual on-site or net power). This difference is due to a variety of factors including, but not limited to, accessories (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions (temperature, humidity, altitude), and engine-toengine variability. Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for this Series engine.
STEERING ASSEMBLY 41 6 33 45 1 1 0 1 16 64 63 13 8 8 60 63 5 9 19 35 59 1 8 6 66 9 8 1 58 6 6 6 61 4 14 15 6 5 13 69 14 8 68 0 15 13 steering-tex_husqsr_3_r1 53 1
STEERING ASSEMBLY 41 1 53 4 45-43 Wheel, Steering 53 19 59-68 Axle Asm., Front 4 53 40 30-8 Spindle Asm., LH 5 53 40 30-88 Spindle Asm., RH 6 53 1 49-31 Bearing, Race Thrust Harden 53 1 1-48 Washer 5/3 x 1-5/8 x 16 Ga. 8 81 00 00-9 Ring, Klip #T5304-5 9 53 1 1-3 Cap, Spindle 13 53 1 1-49 Washer 5/3 x 1-1/4 x 16 Ga. 14 810 04 06-00 Washer, Lock Hvy Hlcl Spr 3/8 15 83 54 06-00 Nut, Crown Lock 3/8-4 unf 16 53 4 93-3 Shaft Steering 19 53 19 4-9 Plate Steering 0 53 40 9-63 Boot, Steering 1 53 18 6-3 Adapter, Wheel Steering 53 4 05-3 Strg. Supt. Lower 6 53 4 41-4 Insert, Wheel Steering 8 81 00 06-1 Screw 3/8-16 x 3/4 33 810 04 05-00 Washer Lock 5/16 35 53 19 4-3 Gear, Sector Plate 45 819 38-1 Washer /3 x 3/8 x 1 Ga. 53 53 18 89-6 Washer Hardened.93 x 1.63 x.060 5 53 40 4-65 Bracket Upstop 58 53 19 4-4 Bolt Shoulder Sector Pivot CFM 59 53 19 4-48 Washer Thrust Sector Steering 60 83 9 10-00 Nut Flange Lock 5/8-61 53 19 4-40 Draglink, LH 6 53 19 4-41 Draglink, RH 63 81 00 05-1 Screw 5/16-18 x 3/4 64 53 19 98-49 Retainer Clip Spring Steering 66 81 0 0-48 Bolt Hex Fghd /16-14 x 3 Serr 6 53 19 4-3 Bushing PM Front Axle 68 83 90 0-00 Nut Lock Flange /16-14 Gr. 5 69 53 19 91-6 Washer 1.5 x.505 x.8 0 53 19 61-9 Bracket Deck Susp. Front 1 53 19 0-5 Shaft Extension Steering 53 4 89-8 Bolt Fin Hx 5/16-18 x 4 1 53 44 49-6 Cap Gear Sector NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm 13
MOWER DECK 44 0 6 1 15 3 16 5 101 43 10 10 90 89 91 95 9 40 98 13 95 14 105 15 43 5 16 84 18 18 91 16 1 6 1 13 14 8 4 1 3 9 6 4 0 5 96 9 14 5 0 19 11 19 0 3 6 5 10 103 9 1 0 104 101 93 0 5 94 3 16 91 18 1 13 100 19 130 131 98 99 3 99 33 45 100 34 14 106 35 88 8 86 85 tex-deck_crd_1 36 14
MOWER DECK 44 1 53 43 69-0 Deck Weldment 3 83 90 05-00 Nut Lock Hex Flange 5/16-18 5 81 00 05-10 Bolt 5/16-18 53 41 63-58 Screw #10 x 0.50 BOS Thread 53 13-9 Screw Thd Roll 1/4-0 X 5/8 13 8 06-1 Bolt Carr Sh 3/8-16 X 1-1/ Gr. 5 14 53 15 60-85 Keeper Belt Idler 16 83 90 06-00 Nut Lock FlG 3/8-16 unc 1 53 40 0-34 Nut Flange Lock Top 18 53 18 6-90 Washer Spacer Mandrel 19 53 04-85 Bearing Ball Mandrel 0 53 1 39-84 Screw Thread Roll 3 81 49 06-8 Screw Thdrol 3/8-16 X 1-3/4 10 81 00 06-16 Screw 3/8-16x1 smgml tap 53 43 9-6 V-Belt Drive 3 53 40 18- Spring Return Deck 33 53 18-81 Housing Mandrel 4pt Service 34 53 19 8- Shaft Asm Mndrl N/Greaseable38 35 53 4 9-84 Blade Mower LH 36 53 19 30-03 Bolt/Washer Asm /16-0 unf 3 819 13 13-16 Washer 13/3 x 13/16 x 16 Ga. 40 53 19-58 Keeper Belt Engine LH 4 81 00 05-1 Screw 5/16-18 x 3/4 43 53 19 4-3 Pulley Mandrel 45 53 13 1-5 Housing Mandrel 6 53 40 9-9 Handle Clutch Cable 0 53 40 1-46 Clutch Asm Manual LT Pred 53 44 68-10 Chute Upper 5 53 13 14-94 Pulley Idler Flat 6 53 41 55-98 Washout Port 84 53 43 5-0 Keeper Belt LH Mandrel 85 53 4 9-85 Blade Mower RH 86 53 18 1-13 Bolt 3/8-4 x 1.50 Gr. 8 8 810 03 06-00 Washer Lock Hvy 3/8 88 53 14 0-96 Washer Hard Blade Mower Vented 89 53 43 81-4 Arm Brake 9 LH 90 53 19 90-9 Spacer Retainer 91 819 13 0-1 Washer 13/3 x 1-1/4 x 1 Ga. 9 53 43 69-93 Rod Brake 93 53 43 81-5 Arm Brake RH 94 53 19-50 Bracket Clutch Cable 95 81 00 06-1 Screw 3/8-16 x 3/4 96 53 40 0-1 Spacer 9 53 18 0-61 Shield Idler Mower 98 53 19 51-61 Stud Fastener 99 53 19 51-86 Arm Suspension Mower Rear 100 53 19 65-39 Bolt Shoulder 101 83 68 09-00 Nut Crownlock 9/16-18 unc 10 53 40 5- Spacer Bearing Swing Plate 103 53 43 69-9 Guard Front Vent 104 53 44 14-9 Mandrel Cover RH 105 53 44 14-8 Mandrel Cover LH 106 53 19 3-16 Spring Brake Return 0 53 41 53-56 Gear Output 1 53 43 69-9 Gasket Gearcase 53 44 38-5 Shaft Gearcase 3 53 43 85-33 Plug Oil 4 53 43 85-34 Valve Relief 5 818 03 10-16 Screw Torx #10-4 x 1 6 8 04-14 Bolt 1/4-0 x 1.5 Gr. 5 83 90 04-00 Nut Hex Flange 1/4-0 unc 8 53 43 69-89 Arm Clutching 9 53 43 81-66 Gearcase Subasm 10 53 43 69-91 Keeper Belt RH 11 53 43 69-85 Washer 14 53 43 69-86 Non Greasable Mandrel Shaft 15 53 44 04-0 Bracket Idler Chasses 1 53 19 34-06 Bolt Shoulder 3/8-16 x 3-5/8 Gr. 5 18 53 1 48-3 Wheel Guage 19 53 40 48-51 Rod Anti-Sway 130 819 13 13-1 Washer 13/3 x 13/16 x 1 Ga. 131 53 19 4-08 Pin Cotter 5/16 Bow Tie Lock 13 53 1 88-99 Knob Handle 15 53 44 04-88 Cable Clutch Manual w/spring - - 53 19 8-0 Mandrel Assembly (Includes Housing, Shaft Assembly, And Bearing Only - Pulley/Nut/Washer And Blade Bolt/Washers Not Included) - - 53 44 8-19 Replacement Mower Complete NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm 15
MOWER LIFT 45 8 89 90 98 3 10 9 100 88 9 91 101* 89 8 lift-tex_34 *Key 91 may be substituted for Key 101 53 43 69-96 Deck Lift 3 53 19 5-31 Lever Asm., Lift RH 53 41 15-55 Grip, Lever 10 53 19 63-14 Spring Torsion 8 53 19 4-09 Pin Cotter /16 Bow Tie Lock 88 53 43 69-95 Spring Lift Assist 89 819 19 19-1 Washer 1/3 x 1-3/16 x 1 Ga. 90 53 19 4-08 Pin Cotter 5/16 Bow Tie Lock 91 53 19 51-81 Link Lift Susp Mower Rear 9 81 49 06-08 Screw 3/8-16 x 1/ 98 53 19 5-0 Link Lift Susp. Front Mower 100 83 93 06-00 Nut Centerlock 3/8-16 101 53 40 0-03 Link Asm Lift FXD NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm 16
SEAT ASSEMBLY 4 8 1 8 8 8 41 40 10 1 6 3 44 43 3 1 3 seat-tex_6.5sl_1_r1 1 53 41 14-05 Seat 53 18 01-66 Bracket Pnt Pivot Fender 3 53 14 06-5 Strap 6 83 80 06-00 Nut Lock Hex w/ins 3/8-16 53 1 41-81 Spring Seat Cprsn 50 Blk Zi 8 53 1 18- Bolt 5/16-18 unc x 3/4 10 53 19 69- Pan Pnt Seat 1 53 1 18-5 Bolt Shoulder 5/16-18 unc-a 3 83 80 05-00 Nut Hex Lock w/ins 5/16-18 40 53 19 6-61 Handle Slide 41 53 19 8-00 Spring Latch 43 84 6 06-1 Bolt 3/8-16 unc x 3/4 44 819 13 38-1 Washer 13/3 x -3/8 x 1 Ga. NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm 1
BAGGER 46 3 8 9 5 5 1 19 6 8 6 13 5 0 3 14 4 1 3 0 1 1 14 14 14 10 3 Bagger_TEX CRD_15_r1 18
BAGGER 46 1 53 4 86-10 Tube Handle Bagger 4 53 43 96-1 Frame Asm Bagger Top 5 53 41 6-3 Frame Asm Top Bagger 6 53 1 68-5 Rivet Drilled 83 90 04-00 Nut Hex Flange 1/4-0 unc 8 53 4 59-54 Cover Bagger 9 53 41 6-9 Insert Handle Bagger 10 53 43 6-0 Frame Front 53 43 6-1 Tubing Brace Bagger 1 53 4 1-93 Nut Square 1/4 13 53 4 1-80 Screw 1/4 x 1.150 14 53 4 18-00 Bolt Shoulder 1/ x 1.150 19 53 19 4-08 Cotter Pin 5/16 Bow Tie 0 585 36 88-01 Screw Hex Cap 1/4-0 x 1.35 1 53 44 83-0 Bag Asm 3 8 04 04-10 Bolt Carr. 1/4-0 5 53 4 16-14 Spring Latch Bagger 6 81 49 04-1 Screw Hex Wsh. Thdrol. 1/4-0 x 3/4 53 4 1-6 Grommet Rubber 8 53 16 5-8 Grip Handle Black NOTE: All component dimensions given in U.S. inches 1 inch = 5.4 mm 19
10.30.13 CL/TH