Multi Function utomobile Emergency JUMP STRT Tough Carstart Versatile Mobile power Emergency Compact supply lighting Product Instruction For HYP PRO Series 4V Multi Function utomobile Emergency JUMP STRT
. WRNING MUST RED: Please read this instruction carefully before you make any operation on your vehicle. This device contains battery product that may cause personal injuries. If you are uncertain or have questions about this device, please consult your dealer or reseller before use. Product is designed for land use ONLY, other applications are use at your own risk. THIS IS FOR 4V SYSTEM ONLY, DMGES CUSE Y IMPROPER USE WILL SOLELY E USER S RESPONSIILITIES. MUST DO: Do not crank start your vehicle for more than 5 sec, or longer. This will damage your vehicle starting system and over heat the JUMP STRT LiPo battery. s a precaution, please allow JUMP STRT to rest for min., before starting your vehicle. efore using the JUMPSTRT, read and follow the instructions carefully. lso pay close attention to the cautionary statements on the vehicle battery and any other equipment. NOTE: s a safety measure, there is NO VOLTGE present at the clamp ends. The product automatically detects when it is hooked up correctly to a battery, LCD displays the voltage of vehicles battery if the voltage is within 8V~8.4V. Only if JUMP STRT button is pressed, will then deliver the voltage to the clamps. Do not use the device in wet conditions. Unit is not waterproofs. The functionality of device might be affected. Keep the device away from where the children can access. Never attempt to alter or disassemble the product. If there is a problem with the product please contact your dealer for further assistance. Do not allow metal to come in contact with the battery poles. It may spark or shortcircuit the battery and cause an explosion. Stop using the jumpstart when you hear the alarm or cannot turn on the JUMPSTRT. The reason may be from: The jumpstart device voltage is less than V Charge the jumpstart to prevent battery failure. Low battery LED should be lighted, If LED flashes, unit will shut down. The device temperature is higher than F (50 C) Cool the jumpstart to at least 04 F (40 C). 3The jumpstart is connected backwards, incorrectly connected or short connected. Correctly connect the clamps. If VEHICLE battery is less than 4V, there is no safety check to prevent incorrect polarity hook up.
.PRODUCT FUNCTIONS ND FETURES HYP 4V 0 4 7 3 6 3 5 4 Charger Input(4V/) Daul US Power Outlet(5V/.) 3 V Cigarette Port 4 Power utton ON/OFF 5 Jump Start utton 6 Light Mode Selector 7 LCD Display 8 LED Work Light 5 8 9 9 ooster Cable Connector 0 Charging LED & S.O.S. Jump Start, Vehicle or Car Charging Voltage Jump Start attery Status 3 Jump Start Ready Icon 4 Polarity Check Icon 5 Temperature Warning Icon 3.SPECIFICTIONS attery Type Charging Outputs Weight Product Size LiPo 00VC Charger OR VDC IN CR Charger Peak mps: HYP900X:000 VDC 5 Output (with 6 overload protection) US 5VDC,. High Intensity LED W(WH) HYP900X:.9Kg 06mm x 53mm x 0mm Features Self contain power unit to boost or jump start your vehicle dead battery under emergency situation. Reverse polarity alarm warning, short circuit, low voltage and overtemperature protections builtin. V/5 DC power outlet with overload protection provides power for car memory saver (OD II) and other V devices. (if equipped) Charge with a 4V/ C charger and optional V/0.5 DC DUL US 5V/. provides power for small electrical appliances (iphone, ipad, NDROID, PD etc.) High intensity LED light can be used for emergency lighting and flash. LCD display shows the both LiON and vehicle leadacid battery status with voltage test functions. Sparkproof design: Once the vehicle engine has successfully been ignited, this JUMP STRT product will cut off the output power within 3s, therefore the clamps will not be live when remove from battery. Sleep mode: When the device has idled for minutes after turn on, the main power of the device will automatically shut off. 3
4.USING THE OOSTER FUNCTION 4.USING THE OOSTER FUNCTION WRNING Ensure that you are using this on a 4 VOLT SYSTEM ONLY, otherwise the battery could explode. Please strictly follow the following steps, otherwise, it could cause damage to the jumpstart, the vehicle or personal injury and death! USING JUMP STRT OPERTION STEPS Put the black clip () terminal attach to LCD displays the voltage and capacity the battery negative post or chassis ground, put the red clip () terminal of device battery, must be >3V for attach to the battery negative post. best results. Firmly insert the end of * larm will beep if polarity is wrong. the cable into the JUMP STRT. (First utton will flash in RED, and LCD icon time use might feel some resistance to POLRITY CHECK" will flash. ** If car battery is completely dead, Go be pushed in all the way.) to Step 3. Step 5 Step 6 Once vehicle started successfully Remove the clamps Step Hookup the vehicle battery Step Press Power button WRNING Once vehicle started, JUMPSTRT Make sure the JUMPSTRT is off, then ① First to remove the black clip () will turn off within 3 sec. ② Next to remove the red clip () Understand your JUMPSTRT ①Turn ignition to ON and ensure all onboard electronics and /C is off. ②DO NOT allow both (RED & LCK) clamps to contact each Step 3 Ready to crank the vehicle others. Step 4 Starting the vehicle ③If clamps are hooked up in wrong polarity, safety alarm will Press JUMP STRT button to initiate Make sure the is highlighted and boost function, and button will stay solid battery status > 3V. Start the vehicle RED. and should see 8.V as indicated. If start failed, repeat Step 3 process again. Seek other help if start process has been repeated > 5 times. Indication: the is highlight Go to Step 4 Step 4 Step 3 This applies to DED battery(<8v) situation Safety check passed; then power will be ONLY. ready for starting. Correct the polarity if it Hold & press JUMP STRT LIGHT is wrong. If start failed, repeat Step 3 buttons for 3 sec to initiate "phantom" polarity check. If polarity is wrong, the alarm process again. Seek help if start process has been repeated > 5 times. will sound. 4 activate. Onboard relay will be disabled for safety and no power will be provided. ④Only use on vehicles with a 4V system. ⑤Under low temperature(< 0 C/4 F),performance of LiPo battery is deeply affected. fter a few attempts to generate power to start car, the LiPo battery should warm up to a desire temperature to yield maximum electrical performance. ⑥If vehicle doesn't start, wait minutes before attempting to restart. If car can't start more than 5 times, STOP and seek other help. ⑦Disconnect both clamps immediately once vehicle starts. ⑧fter each use, always recharge the JUMPSTRT battery fully. 5
5.CHRGING USING C OR DC CHRGER CUTION 6.USING THE 5V V DC OUTPUT POWER SOURCES. Charge via C battery charger. Charge via DC daptor Connect C battery charger to Connect the DC adaptor to the Device s 4V DC inlet devices 4V DC inlet. ttach the C battery charger to ttach the DC adaptor to car C mains, the charge of device l i g h t e r s o c k e t. C h a r g e w i l l will commence automatically Commence automatically 3.Charging Indications Please refer to the table of LCD indications as below for showing the charge status and battery capacity. Once charging is completed, LCD will be Green. LCD indications battery voltage attery Capacity 4.5V~5.V 00% Press power on button, all output sources 5/V are ready to go. Note: The maximum power of the V is 75W. If the power of your appliance is more than 75W, the socket output will shut down automatically. The maximum power of the 5V is 5W. If the power of your appliance is more than 5W, the US output will shut down automatically. 7. USING THE VOLTGE TEST FUNCTION Press power on button. Ensure engine is OFF. 3The clamps connected with battery of vehicle, the V of LCD will flash. Voltage at the LCD is the car battery currents status. 3.7V~4.4V 80%.9V~3.6V 60%.V~.8V 40%. 0V 0% Use only the brand certified charger included with your jumpstart to recharge. Nonstandard products will shorten the life of the battery, void the warranty and might post other risks. Charge your JUMPSTRT battery for 4 hours before using for the first time. 3Recharge the jumpstart battery after each use if possible, and thereafter, at least every 6 months. 4Cannot charge outside at <5 to >40 range, alarm will beep and LCD icon TEMP" will flash. 6 8. MINTENNCE lways inspect the JUMPSTRT before use to ensure the cables are in perfect condition and the clamps are clean and free from corrosion. Keep your JUMPSTRT clean by wiping with a damp cloth. DO NOT use solvents as a cleaning agent. 3Recharge your JUMPSTRT every 6 months for FULL battery. 7
9. PERFORMNCE OF HYPSERIES @ 7.5 C TO 5 C 0. CCESSORIES (if equipped) Diesel Engine Model 6LL >5L 0% attery 50% attery 0% attery 50% attery HYP90004 Device has sufficient power to crank vehicle engine by itself. Device may have adequate power to crank the vehicle engine depends onthe vehicle battery and environment conditions. Device DOES NOT have enough power to crank the vehicle engine. US LED Lamp Notes:. attery status "0% or 50%" listed in the table above is referred as the vehicle's own battery.. Test results are measured under STP condition, 5 & atm. lligator Clamps m Car Charger DC/C Inverter V LED lighting C dapter lligator Clamps m 8 9
. STTEMENT OF LIMITED WRRNTY Our company warrants that each device ) is free from defects in materials and workmanship and ) conforms to our company's official Published Specifications which are available on request. The warranty period for the device starts on original date of purchased; one() year parts and labor for the entire unit except for the battery which has a six(6) months warranty. The date on your invoice or sales receipt is the date of purchased unless our company or your reseller informs your otherwise. Unless our company specifies otherwise, these warranties apply only in the country or region in which you purchased the device. THESE WRRNTIES RE YOUR EXCLUSIVE WRRNTIES ND REPLCE LL OTHER WRNTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, UT NOT LIMITED TO, THE IMPLIED WRRNTIES OR CONDITIONS OF MERCHNTILITY ND FITNESS FOR PRTICULR PURPOSE, SOME STTES OR JURISDICTIONS DO NOT LLOW THE EXCLUSION OF EXPRESS OR IMPLIED WRNTIES, SO THE OVE EXCLUSION MY NOT PPLY TO YOU. IN THE EVENT, SUCH WRRNTIES RE LIMITED IN THE DURTION TO THE WRRNTY PERIOD. NO WRRNTIES PPLY FTER THT PERIOD. SOME STTES OR JURISDICTIONS DO NOT LLOW LIMITTIONS ON HOW LONG N IMPLIED WRRNTY LSTS, SO THE OVE LIMITTION MY NOT PPLY TO YOU. This warranty does not cover the following: failure resulting from misuse, accident, modification, unsuitable physical or operating environment, or improper maintenance by you. failure caused by a product for which our company is not responsible; and any non our company approved products. The warranty is voided by removal or alternation of identifications labels on the device or its parts. This warranty does cover the following: For warranty claims or repair, please contact your local reseller or authorized distributor for further information. any manufacture defects that are under normal operation circumstance. 0. NSWERS FOR COMMON PROLEMS Q: How much time will it takes to charge the JUMP STRT? : First initial charge is suggested to be 4 hours. fter that in a normal situation, 6 hours should charge up completely. The JUMP STRT will shut down the charging circuit once it is fully charged (LCD will lighted in Green), so you will never over charge the device. Q: How to charge the JUMP STRT device? : You can either charge it with C adapter from the wall outlet. The adapter is a universal unit from 0 40V 50/60 Hz. Or you may have an additional optional V vehicle adapter as an accessory. Q: Car won't start, it seems there is no power provided from JUMP STRT. : Make sure polarities are align correctly. Make sure there is more than 3V battery power indicated on the LCD. Make sure you press the "JUMP STRT" button, otherwise, there will be no power transfer to the car. If JUMP STRT has been stored under extreme cold weather conditions, allow it to reach to a warmer temperature by starting your car for a few times. Q: Will the unit blow up if I short circuit the RED and LCK terminal together? : NO absolutely NOT! Unlike other products in the market place, the JUMP STRT has a builtin polarity safety circuit to shut itself down for your extra protection. Q: My car battery has zero power and JUMP STRT does not pass polarity test! : If you car battery has absolutely no power (<8V), you need to override the JUMP STRT safety polarity check circuit in order to send power to the car. First, make sure you put the correct polarity terminal onto to the battery, then hold and press the "JUMP STRT" "Light" button for 3 sec., this will allow the unit to enter safe mode. Then power will flow into the car battery and ready for starting. Q: I have tried to boost a vehicle but not successful. The JUMP STRT is now disabled with no LED work light or 5V US power. : In case of this situation, you might have triggered the safety protection circuit for the DC outputs and this locked out all output power functions. To unlock and reset the unit; simply charge the unit with C plug or DC car charger (if so equipped). The unit should take charge in a few minutes and return to a normal state. For any reason if this does restart, please contact factory or your authorized distributor.
3. WRRNTY CERTIFICTE Record the following information for safe keeping. Product model Purchase date Dealer name Dealer address Dealer phone no. Dealer email Cause of failure User name User phone no. User address User email M00E