ROUND BALERS Rev 03-07 Part No. 4903WP PART'S MANUAL An Operator's Manual was shipped with the equipment in the Manual Canister. This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator's Manual is not with the equipment, contact your dealer or M&W (800-446-5158) to obtain a Free copy before operating the equipment. MODEL 4500 SERIAL NUMBERS 10820 - CURRENT MODEL 4590 SERIAL NUMBERS 10904 - CURRENT M&W 1020 South Sangamon Ave. Gibson City, Illinois 60936 217-784-4261 2007 Alamo Group Inc.
TO THE OWNER/OPERATOR/DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. BEFORE YOU START!! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense! WARRANTY INFORMATION: Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic failure with possible injury or death.
Parts Section 1 PARTS SECTION
PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required. 2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered. 3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number, and the basic name of the part. 4. The Manufacturer reserves the right to substitute parts where applicable. 5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order. 6. The Manufacturer reserves the right to change prices without prior notice. NOTE: Please refer to The Safety Section in the front of this Manual for the proper Part Number when ordering Replacement Safety Decals. For maximum safety and to guarantee optimum product reliability, always use genuine Alamo Group Parts. The use of inferior replacement parts may cause premature or catastrophic failure which could result in serious injury or death. Direct any questions regarding parts to: M&W 1020 South Sangamon Ave. Gibson City, Illinois 60936 217-784-4561 2007 Alamo Group Inc. Parts Section 2
PART NAME INDEX BALE BUMPER RAMP EXTENTION - 4590 BALER... 67 BALE COUNT SENSOR - MODEL 4590... 53 DECAL LOCATION GUIDE... 4 DUAL TWINE DRIVE ASSEMBLY... 28 DUAL TWINE TIE SYSTEM... 24 ELECTRICAL SCHEMATIC - MODEL 4500... 55 ELECTRICAL SCHEMATIC - MODEL 4590... 57 ELECTRICAL SYSTEM - MODEL 4500... 49 ELECTRICAL SYSTEM - MODEL 4590... 51 ELEVATOR... 20 FRONT CHAMBER... 6 GEARBOX... 43 GEARBOX *... 45 HYDRAULIC CYLINDER... 37 HYDRAULIC CYLINDER *... 35 HYDRAULIC SYSTEM... 39 HYDRAULIC SYSTEM - 1450438 (4500 OPTION & 4590 STANDARD EQUIPMENT)... 58 IID SHAFT ASSEMBLY... 47 M&W ROUND BALER MODEL 4500 BALER BALE BUMPER INSTALLATION INSTRUCTIONS... 65 OPTIONAL - WINDROW GATHERING WHEEL (KIT #1450437)... 72 PICK-UP... 41 REAR CHAMBER Rev 03-07... 10 ROUND BALER OPTIONAL BALE GRABBER KIT PART NO. 1450404 INSTALLATION INSTRUCTIONS... 63 ROUND BALER OPTIONAL HYDRAULIC LIFT PICK-UP KIT PART NO.1450438 INSTALLATION INSTRUCTIONS... 59 ROUND BALER OPTIONAL SAFETY CHAIN KIT PART NO. 1450402 INSTALLATION INSTRUCTIONS... 69 SAFETY LIGHTS... 61 UNDERSIDE... 14 WIRE HARNESS ROUTING... 70 WRAP ROLL MOUNTING SYSTEM - MODEL 4590... 34 WRAP SYSTEM ASSEMBLY - MODEL 4590... 30 2007 Alamo Group Inc. Parts Section 3
DECAL LOCATION GUIDE 2007 Alamo Group Inc. Parts Section 4
DECAL LOCATION GUIDE ITEM PART NO. QTY. DESCRIPTION 1410409-4500 DECAL KIT # 1410410-4590 DECAL KIT # 1 D103 1 PTO SPEED (540 RPM) 2 1428302 2 FILL LINE DECAL 3 1438333 3 GREASE DECAL. 10 HRS 4 1438303 1 PICK-UP PIN 5 1438310 2 LARGE M & W 6 1438319 4 OIL DECAL 7 1438321 1 CONTROL HOUSING DECAL (NOT SHOWN) 8 1438326 1 DOG CLUTCH DECAL 9 1438327 1 ELEVATOR CHAIN ADJUSTMENT DECAL 10 1438330 1 CAUTION OPERATING DECAL 11 1438339 3 DANGER - SHARP KNIFE DECAL 12 1458367 1 DOOR SAFETY LOCK VALVE 13 1458363 1 DOUBLE TWINE INSTALLATION INSTRUCTION DECAL 14 1458310 1 PICK-UP CRANK DIRECTION DECAL 15 1458311 1 PICK-UP HEIGHT POSITION DECAL KIT 16 1458382 4 HAND PINCH DECAL 17 0296276 4 PINCH POINT DECAL 18 1458316 2 SAFETY OPERATION 19 1458317 4 DANGER - TAILGATE 20 1458332 1 M & W LOGO, RH 21 1458333 1 M & W LOGO, LH 22 1458334 1 MODEL NO. 4500, RH 1458336 1 MODEL NO. 4590, RH 23 1458335 1 MODEL NO. 4500, LH 1458337 1 MODEL NO. 4590, LH 24 1458338 1 FRONT STRIPE DECAL 25 1458339 2 REAR STRIPE DECAL 26 00756059 3 OIL LEAK DECAL 27 2738332 2 RED OBLONG DEFLECTOR 28 5W118 1 SLOW MOVING VEHICLE 29 2738315 1 IID SHIELD (OUTER DECAL) 30 2738320 1 IID SHIELD (INNER DECAL) 31 1458380 1 MADE IN USA 32 1458362 1 WARNING - BALER UPSET 33 00773723 1 DRIVELINE - SPANISH TRANSLATION 34 00776031 1 CANISTER MANUAL 35 32901C 2 LOCKNUT 36 00024100 4 FLATWASHER 37 00021400 2 BOLT 38 4903WC 1 MANUAL FOR CANISTER 39 00776481 1 INSTRUCT DECAL - MANUAL OPERATOR S INSIDE Indicates Decal Located 2007 Alamo Group Inc. Parts Section 5
FRONT CHAMBER 2007 Alamo Group Inc. Parts Section 6
FRONT CHAMBER ITEM PART NO. QTY. DESCRIPTION 1 1458703 2 RUBBER STOP 2 1452391 1 TWINE BOX FLOOR 3 5E805 2 TYRAP 4 1450200 1 TONGUE 5 1451562 7 TWINE DIVIDER ROD 6 1458702 1 RUBBER HOLD DOWN STRAP 7 1410133 1 DIVIDER PANEL (UPPER) 8 6D9016 34 FLANGED WHIZLOCK NUT 9 1458601 2 GAS SPRING ASSEMBLY W/BALL STUDS 10 1450371 1 TWINE BOX COVER 11 1452317 1 FRONT CHAIN GUARD 12 00023500 13 FLATWASHER 13 31102H5C 23 BOLT 14 6D9001 4 SHEET METAL SCREW 15 1450206 1 FRONT HOUSING 16 40010000 1 COTTER PIN 17 1431565 1 IID SHAFT TRANSPORT SUPPORT 18 3267F4C 10 PHILLIPS FLATHEAD SCREW 19 42066 2 ROLL PIN 20 1432500 2 HINGE PIN 21 49072 2 COTTER PIN 23 10119000 2 BOLT 24 32902C 2 HEX LOCKNUT 25 32943C 2 ELASTIC STOP NUT 26 1436016 2 CAM YOKE ROLLER BEARING 27 312010H8C 2 BOLT 28 49208 2 HAIRPIN COTTER 29 1431625 2 SPRING WASHER 30 1437433 2 COMPRESSION SPRING 31 1431222 2 SPRING BAR 32 1438604 1 JACK STAND 33 02845500 2 BOLT 34 1432535 1 JACK PIN 35 1436782 1 PLASTIC KNOB 36 1432534 1 KNOB STUD 37 1437425 1 COMPRESSION SPRING 38 300619H5C 2 BOLT 39 32947C 4 ELASTIC STOP NUT 40 33007C 2 HEX NUT 41 1451525 2 ADJUSTING BLOCK 42 30068H5C 2 BOLT 43 00001400 2 FLATWASHER 44 1455801 1 TWINE BOX HINGE 45 1450286 1 TWINE BOX LID 46 3263N4C 18 PHILLIPS PANHEAD SCREW 47 329023C 18 HEX LOCKNUT 49 02025700 1 BOLT 50 00757908 1 SAFETY CHAIN 51 00002701 1 FLATWASHER 52 32908C 1 HEX LOCKNUT 53 1452049 REF DIVIDER PANEL, LOWER 54 1451936 1 END PLATE, RH BLANK 55 00011700 7 LOCKWASHER 56 37021H5C 4 CARRIAGE BOLT 57 00021800 6 HEX NUT 58 1430263 1 HINGE PLATE 59 3263N13C 4 PANHEAD SCREW 60 1458413 2 FLEXIBLE DRAW LATCH 61 360015C 4 EXT. TOOTH LOCKWASHER 62 330213C 4 HEX MACHINE NUT 63 1431556 2 TWINE GUIDE BUSHING 64 1438203 2 RETAINING RING 2007 Alamo Group Inc. Parts Section 7
FRONT CHAMBER 2007 Alamo Group Inc. Parts Section 8
FRONT CHAMBER ITEM PART NO. QTY. DESCRIPTION 65 1452076 1 BALE SIZER - RIGHT (NOT SHOWN) 1452077 1 BALE SIZER - LEFT 66 37021H5C 6 BOLT 67 00011700 6 LOCKWASHER 68 00021800 6 HEX NUT 2007 Alamo Group Inc. Parts Section 9
REAR CHAMBER Rev 03-07 2007 Alamo Group Inc. Parts Section 10
REAR CHAMBER Rev 03-07 ITEM PART NO. QTY. DESCRIPTION 1 6D9001 18 SHEET METAL SCREW 2 1452313 1 REAR UPPER CHAIN GUARD 3 00023500 22 FLATWASHER 4 00011700 10 LOCKWASHER 5 00035900 14 BOLT 6 1410112 1 REAR MIDDLE CHAIN GUARD (INCLUDES ITEM 58) 7 1410111 1 REAR LOWER CHAIN GUARD (INCLUDES ITEM 58) 8 3263N9C 2 PHILLIPS PANHEAD SCREW, NO. 9 600321 2 CLAMP, SUPPORT 10 1427302 2 VINYL TUBE 11 1426784 2 "Y" CONNECTOR 12 360015C 4 EXTERNAL TOOTH LOCKWASHER 13 63121700 4 NUT 14 11D9005 8 FLANGED WHIZ NUT 15 1428302 2 FILL LINE DECAL 16 1420105 1 TANK ASSEMBLY, LH 17 1420104 1 TANK ASSEMBLY, RH 18 00002700 4 FLATWASHER 19 1431566 2 SPRING ANCHOR PIN 20 1451210 2 SPRING ADJUST LEVER 21 33115C 2 HEX JAM NUT 22 1437428 2 LATCH SPRING ASSEMBLY 23 37033C 2 CARRIAGE BOLT 24 6D9017 4 FLANGED WHIZLOCK NUT 25 00011100 6 FLATWASHER 26 32905C 2 HEX LOCKNUT 27 1451044 2 LATCH BAR 28 1434868 2 LATCH PIVOT BUSHING 29 00001400 2 FLATWASHER 30 00752658 2 BOLT 31 00010300 2 LOCKWASHER 32 00007000 2 BOLT 34 1438449 2 ADJUSTABLE YOKE END 35 02816800 2 HEX NUT 36 1452518 2 CLEVIS ROD 37 1437126 2 HYDRAULIC CYLINDER 38 32915C 2 HEX LOCKNUT 39 1451248 2 UNLATCH ROD CLEVIS 40 02959924 2 HEX TOP LOCKNUT 41 000640 2 HEX LOCKNUT 42 1452522 2 UPPER CYLINDER PIN 43 310010H5C 2 BOLT 44 15B1600 8 SAE FLATWASHER 45 30067H5C 1 HEX TAP BOLT 46 33007C 2 HEX NUT 47 02030700 2 BOLT 48 31408C 4 BOLT 49 1422182 4 MOUNTING STRAP 50 00021400 8 BOLT 51 1435500 2 BEARING CASTING 52 15B800 4 FLATWASHER 53 00001800 4 LOCKNUT 54 3267F4C 10 PHILLIPS FLATHEAD SCREW 55 6D9016 10 FLANGED WHIZLOCK NUT 56 42066 1 ROLL PIN 57 1432515 1 HINGE PIN 58 1458417 10 HEX INSERT 59 300518H5C 2 HEX TAP BOLT 60 40010000 2 COTTER PIN 61 41954 2 CLEVIS PIN 62 380413C 2 SAE FLATWHASHER 63 1426783 AR CAP 2007 Alamo Group Inc. Parts Section 11
REAR CHAMBER Rev 03-07 2007 Alamo Group Inc. Parts Section 12
REAR CHAMBER Rev 03-07 ITEM PART NO. QTY. DESCRIPTION 64 1452388 1 CHAIN DOOR, RH 65 1452387 1 CHAIN DOOR, LH 66 1458413 2 FLEXIBLE DRAW LATCH 67 3263N13C 2 PANHEAD MACHINE SCREW 71 32902C 12 HEX NUT 73 1450207 1 REAR HOUSING 1450420 INSERT TOOL KIT (INCLUDES TOOL AND 5 INSERTS) 74 00749130 2 BOLT 75 1470239 1 WDMT,RIGHT GUARD MOUNTING 76 1470240 1 WDMT,LEFT GUARD MOUNTING 77 6D9007 6 HEX FLG WHIZ TYP B 5/16 X 1/2 2007 Alamo Group Inc. Parts Section 13
UNDERSIDE 2007 Alamo Group Inc. Parts Section 14
UNDERSIDE ITEM PART NO. QTY. DESCRIPTION 1 1452500 1 TIE ROD, 60" 2 1410221 2 SPINDLE 3 00000200 9 HEX NUT 4 00001200 20 HEX NUT 5 1431563 2 COVER MOUNT STUD 6 1410159 1 CROSS BEAM COVER 7 380434C 1 SAE FLATWASHER 8 1458610 1 NYLON STRAP 9 1450284 1 SUPPORT BRACKET 10 02023900 2 HEX JAM NUT 11 3906A3C 2 SQUAREHEAD CUP POINT SETSCREW 12 1436017 2 SPHERICAL BEARING 13 1432512 1 REAR ROLLER AXLE 14 1430344 1 REAR ROLLER 15 1436203 1 ROLLER CHAIN 16 40641.5 1 KEY 17 1430223 1 FRONT ROLLER 18 40641.25 2 KEY 19 6D5206 1 CONNECTING LINK 20 6D5210 1 OFFSET LINK 21 000640 18 HEX LOCKNUT 22 1435504 2 BEARING HOUSING 23 6D5105 2 BEARING CARTRIDGE 24 1450282 1 PICK-UP HOLDER, LH 25 1430327 1 PICK-UP HOLDER, RH 26 6D5249 2 CONNECTOR LINK 27 1430320 2 WHEEL ARM 28 00001300 24 LOCKWASHER 29 00002700 4 FLATWASHER 30 02030700 4 BOLT 31 49053 2 COTTER PIN 32 380010C 4 FLATWASHER 33 1437601 2 WHEEL 34 00019700 6 FLATWASHER 35 1434871 2 SPACER 36 1431222 2 SPRING BAR 37 1438448 6 HEX FLANGE BOLT 39 00011100 10 FLATWASHER 40 1427420 1 COMPRESSION SPRING 41 1457422 1 PICK-UP IDLER ARM LEAF SPRING 42 0538401 12 STUD NUT 43 TR415 2 VALVE STEM 44 0527600 2 WHEEL 45 0527802 2 TIRE 46 1430126 2 MOUNTED TIRE ASSY. 47 0536700 2 HUB CAP 48 33099C 2 HEX SLOTTED NUT 49 0536003 2 BEARING CONE 50 380451C 2 SAE FLATWASHER 51 0536002 2 BEARING CUP 52 0530179 2 HUB & CUP ASSY. 53 0538400 12 DRIVE STUD 54 0536004 2 BEARING CUP 55 0536005 2 BEARING CONE 56 0536800 2 SEAL 57 35009C 6 LOCKWASHER 59 31206C 2 BOLT 60 02892000 4 BOLT 61 1436352 1 SPROCKET 62 00007000 6 BOLT 63 1431206 1 STRIPPER 64 317013H5C 4 BOLT 2007 Alamo Group Inc. Parts Section 15
UNDERSIDE 2007 Alamo Group Inc. Parts Section 16
UNDERSIDE ITEM PART NO. QTY. DESCRIPTION 65 1450248 1 CHAIN TENSIONER ARM 66 1457421 1 COMPRESSION SPRING 67 00023500 5 FLATWASHER 68 000130 1 BOLT 69 63092200 1 BOLT 71 1450247 1 SUPPORT BRACKET, LH 72 1431415 2 GUIDE BAR 73 31405C 4 BOLT 74 00749130 4 BOLT 75 49033 2 COTTER PIN 76 1430321 1 PICK-UP SHIELD 77 710840 1 METRIC KEY 78 1436210 1 ROLLER CHAIN 79 1436360 1 SPROCKET 80 1436353 1 SPROCKET 81 1450112 1 PICK-UP LIFT SCREW CRANK ASSY. 82 42121 3 ROLL PIN 83 1435502 5 CABLE PULLEY 84 1430333 1 PICK-UP 85 700219C 1 HEX NUT 86 60042 5 WIRE ROPE CLAMP 87 1438445 2 HEX FLANGE BOLT 88 1432034 2 WASHER 89 29N132 3 CABLE THIMBLE - 4500 2 CABLE THIMBLE - 4590 90 1434660 2 PICK-UP CABLE SPACER 91 31203C 6 BOLT 92 1431161 2 SUPPORT PLATE 93 613717C8 1 BOLT 94 710850 1 METRIC KEY 95 1456402 1 SHAFT COUPLING 96 00013901 2 HEX NUT 97 3902A6C 2 SQ. HD CP PT SETSCREW 98 49029 1 COTTER PIN 105 1430217 1 TINE BAR 106 700216C 1 HIGH HEX NUT 107 613618C8 1 BOLT 109 1438408 1 QUICK PIN 110 1452523 1 DRIVE SHAFT 111 40631.25 1 KEY 113 42109 1 ROLL PIN 114 1436363 1 SPROCKET 115 1456200 1 ROLLER CHAIN 116 1436776 2 CHAIN GUIDE 117 311011C 4 BOLT 118 32902C 4 HEX LOCKNUT 119 1457407 1 PICK-UP CABLE - 4500 1457408 1 PICK-UP CABLE - 4590 120 00059900 2 BOLT 121 42124 1 ROLL PIN 122 00007800 1 BOLT 123 00002701 6 FLATWASHER 124 1437523 6 FLATWASHER 125 1436351 1 SPROCKET 126 31709H5C 1 BOLT 127 1430204 1 CHAIN TENSIONER 128 1457423 1 SPRING 129 300317C 1 HEX TAP BOLT 130 1436005 4 BEARING 131 1438205 2 RETAINING RING 132 1436357 2 IDLER SPROCKET 133 1430109 2 IDLER SPROCKET ASSY. 2007 Alamo Group Inc. Parts Section 17
UNDERSIDE 2007 Alamo Group Inc. Parts Section 18
UNDERSIDE ITEM PART NO. QTY. DESCRIPTION 134 1451162 1 CHAIN SHIELD SUPPORT ANGLE 135 6D90174 FLANGED WHIZLOCK NUT 136 37031C7 CARRIAGE BOLT 138 1452185 1 ROLLER DRIVE SHIELD 140 1450244 1 PICK-UP CRANK 141 42058 1 ROLL PIN 142 31002C2 BOLT 143 1451109 1 CRANK FACE PLATE 144 11D9005 2 FLANGED WHIZ NUT 145 1451557 1 PICK-UP LIFT INPUT ROD 146 1450241 1 PICK-UP LIFT HOUSING 147 1458403 1 GEAR KIT W/GROOVED PINS 149 1455806 1 DRIVE SCREW 150 1450242 1 PICK-UP LIFT CABLE ARM 154 03101646 2 LOCKWASHER 155 31907H8C 4 SOCKETHEAD BOLT 156 1436014 2 BEARING FLANGETTE 157 1436011 1 BEARING 158 1451252 1 IDLER SPACER GUIDE 159 1431738 1 WASHER 160 1458420 9 MACHINE BUSHING 161 6D5250 1 HALF LINK 162 00726195 1 PIPE 163 380422C 2 FLATWASHER 164 0035900 2 BOLT 165 1462384 1 COVER, HAND HOLE 166 1458417 A/R HEX INSERT (INCLUDED IN ITEM #6) NOTE: For 4590 2007 Alamo Group Inc. Parts Section 19
ELEVATOR 2007 Alamo Group Inc. Parts Section 20
ELEVATOR ITEM PART NO. QTY. DESCRIPTION 1 1435511 2 SLIDING BRACKET 2 420913 2 ROLL PIN 3 1431445 2 CHAIN TENSIONER BRACKET 4 1438440 4 WAVE SPRING WASHER 5 1430220 2 CHAIN GUIDE 6 1438442 6 MACHINED BUSHING 7 1438446 AR MACHINED BUSHING 8 1436009 4 BEARING W/LOCK COLLAR 9 1438200 5 RETAINING RING 10 1435506 2 IDLER SPROCKET 11 1436010 2 LOCKING COLLAR 12 00011700 11 LOCKWASHER 13 00021800 17 HEX NUT 14 1434865 7 PIPE SPACER 15 370211C 7 CARRIAGE BOLT 16 1431890 1 REAR SHAFT COVER 17 1432518 1 ELEVATOR IDLER SHAFT 18 1432524 27 CHAIN CROSS BAR 19 1438202 108 RETAINING RING 20 1437503 162 WASHER 21 1456027 54 BEARING 22 1436205 2 ELEVATOR CHAIN W/CONNECTOR LINK 23 1416200 AR CONNECTING LINK 24 1416201 AR ONE BAR CHAIN SECTION 25 00752658 4 BOLT 26 00010300 4 LOCKWASHER 27 1437432 2 SPRING 28 1432539 2 ELEVATOR CHAIN TENSION SCREW 29 380442C 2 SAE FLATWASHER 30 33007C 8 HEX NUT 31 3922C3C 1 SETSCREW 32 1452502 1 SPRING CAP 33 1457420 1 SPRING SPRING 34 1435502 3 CABLE PULLEY 35 42121 3 ROLL PIN 36 1450235 2 PULLEY MOUNT 37 6D9007 4 SHEET METAL SCREW 39 00023500 4 FLATWASHER 41 37051C 8 CARRIAGE BOLT 42 1436015 4 BEARING FLANGETTE 43 32905C 11 HEX LOCKNUT 44 1436013 2 BEARING 45 1435505 2 DRIVE SPROCKET 46 3920A29C 8 SETSCREW 47 1430261 2 BEARING 48 40642.25 2 KEY 49 1432313 2 STRIPPER PLATE 50 3267F4C 10 PHILLIPS FLATHEAD SCREW 51 1452543 1 ELEVATOR DRIVE SHAFT 52 1430260 1 FRONT SHAFT COVER 53 1438430 6 CUPPED SPRING WASHER 54 40641.75 1 KEY 55 1435512 2 CHAIN LIMITER 56 00011100 4 FLATWASHER 57 00754577 4 LOCKWASHER 58 00754764 4 BOLT 59 1436358 1 SPROCKET 61 1457400 1 CLUTCH CABLE 63 1436355 1 SPROCKET 68 7D5118 1 ROLLER CHAIN CONNECTOR LINK 69 00007800 1 BOLT 70 00002701 4 FLATWASHER 2007 Alamo Group Inc. Parts Section 21
ELEVATOR 2007 Alamo Group Inc. Parts Section 22
ELEVATOR ITEM PART NO. QTY. DESCRIPTION 71 1437523 2 FLATWASHER 72 1436356 1 IDLER SPROCKET 73 1456201 1 ROLLER CHAIN 74 37031C 3 CARRIAGE BOLT 75 1436011 1 BEARING 76 1436014 2 BEARING FLANGETTE 77 40631.5 1 KEY 78 000640 3 HEX LOCKNUT 79 00002700 1 FLATWASHER 80 1457424 1 COMPRESSION SPRING 82 1450246 1 CHAIN TENSIONER ADJUSTMENT 83 00001000 2 WIRE ROPE CLAMP 84 420511 2 ROLL PIN 85 420818 1 ROLL PIN 86 1438406 1 WIRE ROPE THIMBLE 87 1430213 1 LEVER 88 1435801 2 SPECIAL SOCKETHEAD BOLT 89 1432521 2 ROLLER RACE 90 3902A6C 2 SETSCREW 91 00013901 2 HEX NUT 92 1435507 1 DOG CLUTCH, SLIDING 93 1436006 1 BEARING 94 1435508 1 DOG CLUTCH 95 1437423 1 SPRING 96 1431620 1 WASHER 97 1432522 1 DRIVE SHAFT, LH 98 45051 2 GREASE FITTING 99 9D2010 2 LUBE BULKHEAD NUT 100 9D2009 2 LUBE BULKHEAD CONNECTOR 101 9903 2 PIPE NIPPLE 102 9902 1 PIPE NIPPLE 103 121010 1 PIPE ELBOW 105 1420216 1 DRIVE SHEAVE(4590 ONLY) 2007 Alamo Group Inc. Parts Section 23
DUAL TWINE TIE SYSTEM 2007 Alamo Group Inc. Parts Section 24
DUAL TWINE TIE SYSTEM ITEM PART NO. QTY. DESCRIPTION 1 1435501 3 BEARING HOUSING 2 1436005 6 BEARING 3 1436362 1 SPROCKET IDLER SHAFT 4 1438204 5 RETAINING RING 5 1436350 1 SPROCKET DRIVE SHAFT 6 1436425 1 GEAR SHAFT/PINION 7 1436001 2 BUSHING 8 1460155 1 RH TRAVEL PLATE ASSEMBLY (INCLUDES 1 OF ITEMS #9 & #10) 9 1458418 2 STUD 10 42082 2 ROLL PIN 11 1460156 1 LH TRAVEL PLATE ASSEMBLY (INCLUDES 1 OF ITEMS #9 & #10) 12 1450164 1 CHAIN COVER STUD SUB-ASSEMBLY (INCLUDES 4 OF ITEM #55) 13 1450324 1 RH TWINE TRAVEL LIMIT 14 1450325 1 LH TWINE TRAVEL LIMIT 15 1451174 4 KNIFE STRAP 16 31104H5C 2 BOLT 17 00021800 14 HEX NUT 18 37021H5C 4 CARRIAGE BOLT 19 6D9016 8 FLANGED WHIZLOCK NUT 20 1450363 1 CHAIN BEAM 21 1451048 2 TWINE HOOK-WHITE 22 1451173 2 LATCH, TRAVEL 23 1451175 2 KNIFE CARRIER 24 1451353 1 CHAIN GUIDE 25 1451569 2 SPACER, KNIFE CARRIER 27 1456215 2 ROLLER CHAIN 28 1456782 4 SLIDER 29 1457427 2 SPRING 30 1458409 1 CARRIAGE BOLT 31 10062000 8 BOLT 32 31102H5C 5 BOLT 33 00035900 4 BOLT 34 10119000 2 BOLT 35 10121000 2 BOLT 36 32901C 2 HEX LOCKNUT 37 32902C 8 HEX LOCKNUTT 38 32942C 2 ELASTIC STOP NUT 39 00024000 6 HEX NUT 40 33111C 2 HEX JAM NUT 41 00017000 6 LOCKWASHER 42 00011700 7 LOCKWASHER 43 370010C 4 INTERNAL TOOTH LOCKWASHERT 45 37022C 3 CARRIAGE BOLT 47 380419C 8 FLATWASHER 48 6D5206 2 CONNECTING LINK 49 6D5283 2 OFFSET LINK 50 1436775R 1 PLASTIC GEAR 51 1456783 1 DRIVE PULLEY 52 00023500 5 FLATWASHER 53 40621 1 KEY 54 1438204 2 KEEPER 55 1458419 4 STUD 56 4062.56 1 KEY 57 24022 1 SHOULDER BOLT 58 1457429 1 TORSION SPRING, COUNTER 59 1438606 1 COUNTER 60 1452192 1 COUNTER MOUNTING BRACKET 61 3272P5C 4 MACHINE SCREW 62 33025C 4 HEX MACHINE NUT 63 37003C 4 INTERNAL TOOTH LOCKWASHER 64 1452193 1 COUNTER COVER 65 1430193 2 KNIFE BLADE ASSY. 2007 Alamo Group Inc. Parts Section 25
DUAL TWINE TIE SYSTEM 2007 Alamo Group Inc. Parts Section 26
DUAL TWINE TIE SYSTEM ITEM PART NO. QTY. DESCRIPTION 66 3263R2C 4 PHILLIP HEAD SCREW 67 1450166 1 TWINE DRIVE ASSY. (SEE TWINE DRIVE) 68 1451930 1 TWINE GUIDE BRACKET 69 1431556 2 TWINE GUIDE BUSHING 70 1438203 2 RETAINING RING 71 00021400 2 BOLT 72 11D9005 2 FLANGED WHIZLOCK NUT 73 340211C 2 WING NUT 74 1437426 2 SPRING 75 1452184 2 DUAL TWINE BRAKE 76 1458409 2 CARRIAGE BOLT 77 1438205 3 RETAINING RING Items #58-2007 Alamo Group Inc. Parts Section 27
DUAL TWINE DRIVE ASSEMBLY 2007 Alamo Group Inc. Parts Section 28
DUAL TWINE DRIVE ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 1 11D9005 2 FLANGED WHIZ NUT 2 1426426 1 SPUR GEAR, 12 TEETH 3 1427050 1 ELECTRIC MOTOR 4 1451628 1 MOTOR MOUNT 5 330211C 2 HEX MACHINE NUT 6 360014C 2 EXT TOOTH LOCKWASHER 7 42035 1 ROLL PIN 8 1434851 2 BEARING CAGE 9 1436002 2 BEARING 10 1438200 2 RETAINING RING 11 1438202 2 RETAINING RING 12 1450367 1 LOWER IDLER ARM 13 1452532 2 IDLER SHAFT 14 31075C 2 BOLT 15 1450368 1 UPPER IDLER ARM 16 1436003 1 BEARING 17 1436005 1 BEARING 18 1452530 1 SHAFT, FEED ROLLER 19 1452531 1 FEED ROLLER, DUAL TWINE 20 1456425 1 MODIFIED SPUR GEAR, 60 TEETH 21 1458200 1 EXTERNAL RETAINING RING 22 10058000 3 BOLT 23 00017000 6 LOCKWASHER 24 1450366 1 MOUNTING BRACKET 25 1457428 2 SPRING 26 31002H5C 3 BOLT 27 314017C 1 BOLT 28 00001200 1 HEX NUT 30 1431556 2 TWINE GUIDE BUSHING 31 1438203 2 RETAINING RING 32 1451930 1 TWINE GUIDE BRACKET 34 37021H5C 2 CARRIAGE BOLT 33 00024100 2 FLATWASHER 35 6D9016 3 FLANGED WHIZ LOCKNUT 36 00021400 2 BOLT 2007 Alamo Group Inc. Parts Section 29
WRAP SYSTEM ASSEMBLY - MODEL 4590 2007 Alamo Group Inc. Parts Section 30
WRAP SYSTEM ASSEMBLY - MODEL 4590 ITEM PART NO. QTY. DESCRIPTION 1 1456300 1 PULLEY 2 3919A2C 2 SETSCREW 3 1456103 1 V BELT 4 00002700 4 FLATWATER 5 2F031 2 BELT, IDLER 6 00749130 2 BOLT 7 00999418 1 BOLT 8 32905C 4 LOCKNUT 9 1451270 1 IDLER PULLEY ARM 10 1454879 1 IDLER BUSHING RS 11 1457436 1 TORSION SPRINGS RS CLUTCH 12 1452049 1 PANEL, LOWER DIVIDER 13 00021800 39 NUT 14 00011700 37 LOCKWASHER 15 00002000 3 BOLT 16 03101646 5 LOCKWASHER 17 1432034 3 CLUTCH RETAINING WASHER 18 6D5103A 10 FLANGETTE 19 6D5113 5 BEARING 20 1451186 1 CLUTCH BRACKET 21 37021H5C 21 CARRRIAGE BOLT 22 1452533 1 CAM SHAFT 23 00035900 5 BOLT 24 1451121 1 BRACKET, HALL EFFECT 25 1457932 1 CLUTCH, MODIFIED 26 1454885 2 SPACER 27 1450195 1 CUT-OFF CAM ASSY 27A 1450372 1 CAM WELDMENT 27B 3919A9C 3 SETSCREW 27C 5C5180 3 JAM NUT 27D 42069 1 ROLL PIN 28 1452198 1 BRACKET, CAM SWITCH 29 00023500 5 FLATWASHER 31 6D9016 1 LOCKNUT 32 MWSN1192 2 SPRING 33 1450393 2 IDLER, ARM BASE 34 1450374 2 SWING ARM 35 1438203 2 RETAINING RING 36 1460103 1 IDLER ROLLER ASSY 36A 1456007 2 BEARING 36B 1454881 1 IDLER ROLLER 37 1450376 1 NET CHUTE 38 1450176 1 DRIVE ROLLER ASSY 39 1460208 1 END PLATE (RH) 40 10119000 2 BOLT 41 1460100 1 COUNTER RING ASSY 42 1450177 1 TRIP ARM ASSY. 42A 1436016 1 BEARING 42B 1450378 1 TRIP ARM 43 00023100 3 BOLT 44 000640 1 LOCKNUT 45 02044900 1 BOLT 46 1454884 1 STOP, TORSION SPRING 47 1458707 1 BUMPER 48 40010000 2 COTTER PIN 49 1457431 1 TORSION SPRING 50 1460102 1 CUTTER BAR ASSY 50A 1428350 4 KNIFE 50B 3981H1C 10 SCREW 50C 380419C 10 FLATWASHER 50D 1450373 1 CUTTER BAR 51 1454880 1 IDLER BUSHING (LH) 2007 Alamo Group Inc. Parts Section 31
WRAP SYSTEM ASSEMBLY - MODEL 4590 2007 Alamo Group Inc. Parts Section 32
WRAP SYSTEM ASSEMBLY - MODEL 4590 ITEM PART NO. QTY. DESCRIPTION 52 1457430 1 TORSION SPRING 53 1456104 1 V BELT 54 00748823 1 BOLT 55 1456011 2 FLANGETTE 56 1456012 1 BEARING 57 1457902 1 CLUTCH 58 312020H5C 1 BOLT 59 6D9017 3 LOCKNUT 60 1450188 1 END PLATE ASSY. (LH) 61 00011100 2 FLATWASHER 62 00013901 2 NUT 63 1454894 1 SPACER 64 1461207 1 IDLER PULLEY ARM, (RH) 65 380434C 1 FLATWASHER 66 1420216 1 DRIVE SHEAVE 67 3919A3C 1 SETSCREW 68 1451115 1 BELT TENSIONER BRACKET 2007 Alamo Group Inc. Parts Section 33
WRAP ROLL MOUNTING SYSTEM - MODEL 4590 ITEM PART NO. QTY. DESCRIPTION 1 00035900 6 BOLT 2 70014W 1 PLASTIC KNOB 3 1450275 1 ROLL LATCH HANDLE 4 1451561 1 TENSION ROD 5 1450276 1 HANDLE PIVOT BRACKET 6 6D9016 6 FLANGE LOCKNUT 7 42049 1 ROLL PIN 8 1455503 2 ROLL END STOP 9 1450271 1 ROLL LATCH 10 1438447R 1 HOIST EYE 11 00024000 2 HEX NUT 12 1427422 1 EXTENSION SPRING 13 11D9005 2 HEX FLANGE NUT 14 31006H5C 1 BOLT 15 1450600 2 ROLL TUBE MOUNTING 16 1450272 1 ROLL MOUNTING TUBE 17 1451916 3 SPACER WASHER 18 1426789 A/R ROLL/NETTING 2007 Alamo Group Inc. Parts Section 34
HYDRAULIC CYLINDER * ITEM PART NO. QTY. DESCRIPTION 43 1417121 1 BARREL 44 1417126 1 LOCKNUT 45 1417119 1 PISTON 46 2 BACK-UP 47 1 O-RING 48 1 O-RING 49 1417120 1 ROD 50 1 O-RING 51 1 BACK-UP 52 1417123 1 LOCKWIRE 53 1417122 1 HEAD 54 1 O-RING 55 1 BCK-UP 56 1 ROD WIPER HYDRAULIC CYLINDER P/N 2007 Alamo Group Inc. Parts Section 35
HYDRAULIC CYLINDER 2007 Alamo Group Inc. Parts Section 37
HYDRAULIC CYLINDER ITEM PART NO. QTY. DESCRIPTION 1 1417140 1 CYLINDER ROD 2 1417139 1 CYLINDER TUBE 3 1417138 1 CYLINDER HEAD 4 1417141 1 PISTON 5 5JRC12160 1 NUT 6 ------ 1 ROD SEAL 7 ------ 1 ROD WIPER 8 ------ 1 O-RING 9 ------ 1 SEAL 10 ------ 1 O-RING 11 ------ 1 SEAL PSP PISTON 13 00756059 1 DECAL, WARNING HYDRAULIC CYLINDER P/N 2007 Alamo Group Inc. Parts Section 38
HYDRAULIC SYSTEM 2007 Alamo Group Inc. Parts Section 39
HYDRAULIC SYSTEM ITEM PART NO. QTY. DESCRIPTION 1 1457117 1 HYDRAULIC LINE, UPPER RIGHT 2 1457118 1 HYDRAULIC LINE, LOWER RIGHT 3 1457119 1 HYDRAULIC LINE, UPPER LEFT 4 1457120 1 HYDRAULIC LINE, LOWER LEFT 5 1457214 1 HYDRAULIC HOSE(NEW STYLE) 1457209 1 HYDRAULIC HOSE(DISCONTINUED) 6 1457201 1 HYDRAULIC HOSE 7 1457208 1 HYDRAULIC HOSE 8 1457212 4 HYDRAULIC HOSE (NEW STYLE) 1457202 4 HYDRAULIC HOSE (DISCONTINUED) 9 1410149 2 HYDRAULIC CYLINDER (NEW STYLE -SEE PAGE 49) 1437126 2 HYDRAULIC CYLINDER (DISCONTINUED - SEE PAGE 49) 10 1457350 1 DOOR LOCK VALVE 11 1410153 1 PICK-UP HYDRAULIC CYLINDER (NEW STYLE) 1437100 1 PICK-UP HYDRAULIC CYLINDER(DISCONTINUED) 12 1438418 7 2-TWIN CLAMP HALVES 13 1438419 7 TWIN COVER PLATE 16 10121000 7 BOLT 17 1451248 2 UNLATCH ROD CLEVIS 18 00755153 4 COTTER PIN 19 1432525 2 CYLINDER PIN, LOWER 20 1452522 2 CYLINDER PIN, UPPER 21 15B1600 8 FLATWASHER 22 310010H5C 2 BOLT 23 02959924 2 HEX LOCKNUT 24 2437107 1 UNION TEE 25 311010C 2 BOLT 26 1457104 7 ELBOW, MALE 27 1438420 1 TWIN WELD PLATE 28 6D9016 2 FLANGE WHIZ LOCKNUT 29 17003 3 PIPE CAP 30 1458704 1 GROMMET 31 02960018 1 ELBOW ADAPTOR(NEW STYLE) 1457126 1 ELBOW ADAPTOR(DISCONTINUED) 32 32907C 2 HEX LOCKNUT 33 33007C 1 HEX NU 34 1451254 1 CABLE PLATE 35 00001000 1 WIRE ROPE CLAMP 36 1454864 1 TUBE SPACER 37 1451214 1 PICK-UP LIFT CONNECTOR 38 316011H5C 1 BOLT 39 00059900 1 BOLT 40 00011100 2 FLATWASHER 41 000640 1 HEX LOCKNUT 42 15007 1 PIPE BUSHING 57 1437428 2 LATCH SPRING 58 33115C 2 HEX JAM NUT 59 00002700 2 FLATWASHER 60 300518H5C 2 HEX TAP BOLT 61 1431566 2 SPRING ANCHOR PIN 62 420812 2 ROLL PIN 2007 Alamo Group Inc. Parts Section 40
PICK-UP 2007 Alamo Group Inc. Parts Section 41
PICK-UP ITEM PART NO. QTY. DESCRIPTION 1 K9379470 2 SPACER TUBE 2 K9007210 90 BOLT 3 K9100100 88 LOCKWASHER 4 K9379530 2 BEARING PLATE 5 K1437434 36 DOUBLE PICK-UP TINE 6 K9380520 36 CLIP 7 K9087060 36 LOCKNUT 8 K9085120 2 JAM NUT 9 K9105020 2 FLATWASHER 10 K9379280 1 COVER 11 K9080120 4 HEX NUT 12 1438431 4 LOCKWASHER 13 1410213 1 END PLATE, RH 13A 1410219 1 END PLATE, RH 14 K9340060 2 FLANGED BEARING 15 K9381330 1 STRIPPER BAR 16 K9002820 4 BOLT 17 K9381310 4 FLATWASHER 19 1410214 1 END PLATE, LH (LESS ITEMS 40 & 44) 19A 1410220 1 END PLATE, LH (LESS ITEMS 40 & 44) 22 K9124520 4 ROLL PIN 23 K9380800 4 ROLLER BOLT 24 K9380810 4 ROLLER BEARING 25 K9381350 4 ECCENTRIC ARM 26 K9098500 4 EXTERNAL TOOTH LOCKWASHER 27 K9085181 4 HEX NUT 29 K9380830 4 BUSHING, LH 30 K9359000 8 BUSHING 31 K9381050 4 TINE MOUNT BAR 32 K9381370 1 DRIVESHAFT 33 K9010460 36 BOLT 34 K9379601 36 CLIP 36 K9381320 20 SCRAPER 37 K9380680 4 BUSHING, RH 38 1431882 2 PICK-UP SHIELD 39 K9080120 2 HEX NUT 41 613620C8 2 BOLT 43 1431919 1 PICK-UP SHIELD EXTENDER, RH 44 1431920 1 PICK-UP SHIELD EXTENDER, LH 45 1438448 6 HEX FLANGE BOLT 46 1430333 1 PICK-UP COMPLETE, LESS ITEM #38,40,43, & 44 2007 Alamo Group Inc. Parts Section 42
GEARBOX 2007 Alamo Group Inc. Parts Section 43
GEARBOX ITEM PART NO. QTY. DESCRIPTION 1 1416658 1 CASING 2 2716659 2 SHIM 3 2716602 2 BEARING 4 1416659 1 SHAFT 5 2716740 1 SNAP RING 6 00752931 1 PLUG 7 2716658 2 BEARING 8 2716607 2 SNAP RING 9 2716660 3 OIL SEAL 10 1416660 1 CROWN WHEEL 11 2716662 2 SHIM 12 70809C8 4 BOLT 13 1416661 1 EXTENSION 14 1416662 1 PINION SHAFT 15 00756649 1 SNAP RING 16 61368C8 4 BOLT 17 1416657 1 PLUG, DIPSTICK 18 1416663 1 SHIM 19 2716557 1 PLUG 20 1456410 1 GEARBOX COMPLETE -LESS ITEMS 21-29 21 000130 2 BOLT 22 00011100 2 FLATWASHER 23 1456779 1 SAFETY SHIELD 24 03101646 2 LOCKWASHER 25 00013901 2 HEX NUT 26 61394C8 2 BOLT (TOP) 27 00010300 4 LOCKWASHER 28 710850 1 KEY 29 00756373 2 BOLT (BOTTOM) 4500 - Serial 4590 - Serial 2007 Alamo Group Inc. Parts Section 44
GEARBOX * 2007 Alamo Group Inc. Parts Section 45
GEARBOX * ITEM PART NO. QTY. DESCRIPTION 1 000130 2 BOLT 2 00011100 2 FLATWASHER 3 1456779 1 SAFETY SHIELD 4 03101646 2 LOCKWASHER 5 00013901 2 HEX NUT 6 K9363370 1 SEAL 7 1438202 1 RETAINING RING 8 K9111340 FLATWASHER K9111330 FLATWASHER K9111320 FLATWASHER K9111300 FLATWASHER 9 2716539 1 BALL BEARING 10 K9116680 1 RETAINING RING 11 K2730810 1 GEAR COVER 12 K1510420 1 GEARBOX GASKET 13 61368C8 6 BOLT 14 00754577 6 LOCKWASHER 15 61394C8 4 BOLT 16 00010300 4 LOCKWASHER 17 K9321930 1 BEARING 18 K9108910 FLATWASHER K9108900 FLATWASHER K9108890 FLATWASHER 19 K2730280 1 GEAR SHAFT 20 K2804351 1 GEAR HOUSING 21 710850 3 KEY 22 K2800042 1 DRIVESHAFT 23 K2730290 1 GEAR 24 K9363390 2 SEAL 25 K9116730 2 RETAINING RING 26 K9109640 FLATWASHER K9109630 FLATWASHER K9109620 FLATWASHER K9109650 FLATWASHER 27 K9301670 2 BALL BEARING 28 K9060400 2 PLUG 29 K9107270 1 FLATWASHER 30 1456401 1 GEARBOX, COMPLETE - LESS ITEMS #1-5, 15,16, & (2) #21 4500 - Serial 4590 - Serial 2007 Alamo Group Inc. Parts Section 46
IID SHAFT ASSEMBLY 2007 Alamo Group Inc. Parts Section 47
IID SHAFT ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 1 1416640 1 QUICK DISCONNECT REPAIR IT 2 1416585 1 QUICK DISCONNECT YOKE ASSEMBLY, 1-3/8 (6-SPLINE) 3 1416401 2 CROSS & BEARING KIT 4 1416402 1 INBOARD YOKE 5 703624W 2 SPRING PIN 6 1416404 1 INNER PROFILE 7 1416437 2 SHIELD CONE 8 1416438 2 SCREW 9 1416409 2 BEARING RING 10 1416410 1 OUTER SHIELD TUBE 11 2738315 1 IID SHIELD DECAL (OUTER DECAL) 12 1416587 1 IID HALF, TRACTOR END 13 1416405 1 OUTER PROFILE 14 1416411 1 INNER SHIELD TUBE 15 2738320 1 IID SHIELD DECAL (INNER DECAL) 16 1416412 1 SAFETY CHAIN 17 1416406 1 INBOARD YOKE 18 1416442 1 CLUTCH HOUSING 19 1416416 1 QUICK DISCONNECT HUB, 1-3/8 (6-SPLINE) 20 1416419 24 INNER SPRING 21 1416418 24 OUTER SPRING 22 1416417 24 CAM 23 1416443 1 SEAL RING 24 1416444 1 THRUST RING 25 1416422 1 RETAINER RING 26 1416424 1 COMPRESSION SPRING 27 1416425 1 LOCK COLLAR 28 1416423 3 BALL 29 1416426 1 FLANGED RING 30 1416427 1 CIRCLE CLIP 31 1416441 1 QUICK DISCONNECT FLANGE KIT (INCLUDES ITEMS 26-30) 32 1416436 1 RADIAL PIN CLUTCH, COMPLETE (INCLUDES ITEMS 18-30) 33 1416433 1 IID HALF, BALER END (INCLUDES ITEMS 3,5,7,8,9, 13-17) 34 1416400 1 QUICK DISCONNECT YOKE, 1-3/8 (6-SPLINE) 35 1416414 1 QUICK DISCONNECT PIN KIT (INCLUDES ITEM 34) 36 1436401 1 IID SHAFT COMPLETE NOTE: Two types 2007 Alamo Group Inc. Parts Section 48
ELECTRICAL SYSTEM - MODEL 4500 2007 Alamo Group Inc. Parts Section 49
ELECTRICAL SYSTEM - MODEL 4500 ITEM PART NO. QTY. DESCRIPTION 1 33029C 4 HEX NUT 2 37005C 8 LOCKWASHER 3 380413C 6 FLATWASHER 4 360015C 7 EXTERNAL TOOTH LOCKWASHER 5 3276H5C 4 HEX MACHINE SCREW 6 3274F10C 4 SLOTTED FLATHEAD MACHINE SCREW 7 1431170 2 SWITCH BRACKET 8 31102C 3 BOLT 9 600321 6 CLAMP 10 32902C 3 HEX LOCKNUT 11 1450249 2 SWITCH HARNESS 12 1457915 1 WIRE HARNESS, BALER END 13 5E805 11 TYRAP 14 0138629 1 TYRAP 15 1456778 4 BEADED TIE 16 1450175 1 CONTROL HOUSING ASSEMBLY 17 1451120 1 BRACKET-CONTROLLER 18 1456776 2 KNOB 19 1458708 2 ANTI-PIVOT WASHER 2007 Alamo Group Inc. Parts Section 50
ELECTRICAL SYSTEM - MODEL 4590 2007 Alamo Group Inc. Parts Section 51
ELECTRICAL SYSTEM - MODEL 4590 ITEM PART NO. QTY. DESCRIPTION 1 1457932 1 CLUTCH, MODIFIED 2 1457942 1 HARNESS, HALL EFFECT 3 1460209 1 SWITCH 4 1450249 2 SWITCH - HARNESS 5 1457929 1 HARNESS 6 1427050 1 MOTOR 7 1457943 1 SENSOR HARNESS (SEE PARTS BREAKDOWN ON PAGE 64-65) 8 1457902 1 CLUTCH 9 33029C 8 HEX NUT 10 37005C 12 LOCKWASHER 11 3259N10C 4 PANHEAD SCREW 12 1457936 1 HARNESS, CONTROL CORD 13 1457945 1 CONTROL BOX 14 1451120 1 BRACKET, CONTROLLER 15 1458708 2 ANTI PIVOT WASHER 16 1456776 2 KNOB 17 1458424 2 NYLON JAM NUT 18 1431170 2 SWITCH BRACKET 19 3276H5C 4 HEX MACHINE SCREW 20 360015C 4 LOCKWASHER 21 380413C 4 FLATWASHER 22 3274F10C 4 MACHINE SCREW 23 31102C 3 BOLT 24 600321 6 CLAMP 25 32902C 3 HEX LOCKNUT 2007 Alamo Group Inc. Parts Section 52
BALE COUNT SENSOR - MODEL 4590 2007 Alamo Group Inc. Parts Section 53
BALE COUNT SENSOR - MODEL 4590 ITEM PART NO. QTY. DESCRIPTION 1 1454200 1 BRACKET, DOOR HINGE MAGNET 2 33005C 2 HEX NUT 3 1457928 1 ACTUATOR 4 3257N7C 2 MACHINE SCREW 5 38045C 2 FLATWASHER 6 37003C 2 LOCKWASHER 7 33025C 2 HEX MACHINE NUT 8 1457943 1 SENSOR, MAGNETIC 9 3257N7C 2 MACHINE SCREW 10 38045C 2 FLATWASHER 11 37003C 2 LOCKWASHER 12 33025C 2 HEX MACHINE NUT 13 1451125 1 BRACKET, DOOR OPEN SENSOR 14 3263N9C 2 MACHINE SCREW 15 380413C 2 FLATWASHER 16 360015C 2 LOCKWASHER 17 63121700 2 HEX MACHINE NUT 18 1451947 1 SHIELD, DOOR OPEN SENSOR 19 10058000 2 BOLT 20 00024100 2 FLATWASHER 21 11D9005 2 FLANGED LOCKNUT 3. Item #8 4. Verify that NOTES 1. Clearance between 2. Item #3 2007 Alamo Group Inc. Parts Section 54
ELECTRICAL SCHEMATIC - MODEL 4500 2007 Alamo Group Inc. Parts Section 55
ELECTRICAL SCHEMATIC - MODEL 4590 ITEM PART NO. QTY. DESCRIPTION 2007 Alamo Group Inc. Parts Section 57
HYDRAULIC SYSTEM - 1450438 (4500 OPTION & 4590 STANDARD EQUIPMENT) ITEM PART NO. QTY. DESCRIPTION 1 1457214 1 HYDRAULIC HOSE 2 1410153 1 HYDRAULIC CYLINDER, PICK-UP 3 1458704 1 GROMMET 4 02960018 1 90DEGREES ELBOW 5 32907C 2 HEX HEAD LOCKNUT 6 33007C 1 HEX NUT 7 1451254 1 CABLE PLATE 8 00001000 1 WIRE ROPE CLAMP 9 1454864 1 TUBE SPACER 10 1451214 1 PICK-UP LIFT CONNECTOR 11 316011H5C 1 BOLT 12 600343 1 SUPPORT CLAMP 13 15007 1 PIPE BUSHING 14 10119000 1 BOLT 15 32902C 1 LOCKNUT 16 EXISTING COMPONENTS (SEE UNDERSIDE PARTS DRAWING PAGE 36-39) 17 00726195 1 PIPE 2007 Alamo Group Inc. Parts Section 58
ROUND BALER OPTIONAL HYDRAULIC LIFT PICK-UP KIT PART NO.1450438 INSTALLATION INSTRUCTIONS 2007 Alamo Group Inc. Parts Section 59
SAFETY LIGHTS 2007 Alamo Group Inc. Parts Section 61
SAFETY LIGHTS ITEM PART NO. QTY. DESCRIPTION 1 1457937 1 DUAL LAMP (RH) 2 1457938 1 DUAL LAMP (LH) 3 10058000 8 BOLT 4 32901C 8 LOCKNUT 5 1457939 1 MAIN HARNESS 6 1457944 1 WISHBONE HARNESS 7 600343 3 SUPPORT CLAMP 8 5E805 8 TYRAP 9 2427905 1 MALE PLUG 10 2427904 1 SPRING 11 1417917 2 AMBER LENS 12 1417916 1 RED LENS 13 1417918 2 LIGHT BULB 14 1417919 1 BLACK BLANK 15 1417915 1 FRONT HOUSING 16 1417914 1 REAR HOUSING 2007 Alamo Group Inc. Parts Section 62
ROUND BALER OPTIONAL BALE GRABBER KIT PART NO. 1450404 INSTALLATION INSTRUCTIONS 2007 Alamo Group Inc. Parts Section 63
THIS PAGE WAS LEFT BLANK INTENTIONALLY
M&W ROUND BALER MODEL 4500 BALER BALE BUMPER INSTALLATION INSTRUCTIONS 2007 Alamo Group Inc. Parts Section 65
M&W ROUND BALER MODEL 4500 BALER BALE BUMPER INSTALLATION INSTRUCTIONS ITEM PART NO. QTY. DESCRIPTION 1 1421603 1 CROSS CHANNEL 2 1420730 1 MOUNT ANGLE, RH 3 1420731 1 MOUNT ANGLE, LH 4 1421210 2 BRACE STRAP 5 6D9017 4 FLANGED WHIZLOCK NUT 7 000130 4 BOLT 8 33007C 4 HEX NUT 9 00010300 4 LOCKWASHER 10 02675800 4 BOLT 11 32908C 2 HEX LOCKNUT 2007 Alamo Group Inc. Parts Section 66
BALE BUMPER RAMP EXTENTION - 4590 BALER 2007 Alamo Group Inc. Parts Section 67
BALE BUMPER RAMP EXTENTION - 4590 BALER ITEM PART NO. QTY. DESCRIPTION 1 1450398 1 RAMP PIPE 2 1450399 2 PIVOT PIN 3 1452546 2 SPRING ROD 4 1451582 2 SPRING, TRUNION 5 1454898 4 BUSHING, TRUNION 6 1450377 2 RAMP MOUNT 7 1457420 2 SPRING, COMPRESSION 8 1458705 2 RUBBER, CUSHION DONUT 9 45053 2 GREASE FITTING 10 00001400 2 FLATWASHER 11 32907C 4 LOCKNUT 12 00748823 4 HEX HEAD CAP SCREW 13 00001300 4 LOCKWASHER 14 00002700 4 FLATWASHER 15 000130 8 HEX HEAD CAP SCREW 16 03101646 2 LOCKWASHER 17 00013901 2 NUT 18 00011100 6 FLATWASHER 19 6D9017 6 WHIZ LOCKNUT 20 REF 1 BALE BUMPER CHANNEL 2007 Alamo Group Inc. Parts Section 68
ROUND BALER OPTIONAL SAFETY CHAIN KIT PART NO. 1450402 INSTALLATION INSTRUCTIONS ITEM PART NO. QTY. DESCRIPTION 1 02025700 1 BOLT 2 00757908 1 SAFETY CHAIN 3 00002701 1 FLATWASHER 4 32908C 1 HEX LOCKNUT Install the 3/4-10 2007 Alamo Group Inc. Parts Section 69
THIS PAGE WAS LEFT BLANK INTENTIONALLY
WIRE HARNESS ROUTING 2007 Alamo Group Inc. Parts Section 70
WIRE HARNESS ROUTING ITEM PART NO. QTY. DESCRIPTION 1 1457915 1 WIRE HARNESS - BALER END 2 1457944 1 WISHBONE WIRE HARNESS 3 5E805 15 TY-RAP 4 1462354 2 CHANNEL, HARNESS SUPPORT 2007 Alamo Group Inc. Parts Section 71
OPTIONAL - WINDROW GATHERING WHEEL (KIT #1450437) 2007 Alamo Group Inc. Parts Section 72
OPTIONAL - WINDROW GATHERING WHEEL (KIT #1450437) ITEM PART NO. QTY. DESCRIPTION 1 1458709 2 GATHERING WHEEL 2 1451098 2 FLANGE CLAMP PLATE 3 1460312 2 WHEEL HUB 4 00007000 16 BOLT 5 000640 16 LOCKNUT 6 1460307 1 R. SPINDLE 1460308 1 L. SPINDLE 7 00013900 2 BOLT 8 32943C 2 ELASTIC STOP NUT 9 1461009 1 R. STRIPPER & HAY STRAP 1461010 1 L. STRIPPER & HAY STRAP 10 00023100 4 BOLT 11 00011100 8 FLATWASHER 12 03101646 8 LOCKWASHER 13 00013901 8 HEX NUT 14 1460310 1 R. WHEEL ARM 1460311 1 L. WHEEL ARM 15 1460315 2 PIVOT PIN 16 1460313 1 R. MOUNT BRACKET 1460314 1 L. MOUNT BRACKET 17 00753642 4 BOLT 18 10119000 2 BOLT 19 00011700 2 LOCKWASHER 20 00021800 2 HEX NUT 21 45051 4 GREASE FITTING 22 1456022 4 BUSHING 23 1456023 4 BUSHING 24 1452586 2 UPPER LIFT ROD 25 02816800 2 HEX NUT 26 1460309 2 LIFT TUBE 27 1452589 2 LOWER LIFT ROD (SHORT - 21") 28 1457440 2 SPRING 29 42088 2 ROLL PIN 30 40010000 2 COTTER PIN 31 00002700 2 FLATWASHER 32 49207 2 HAIR PIN COTTER 33 1458431 2 THRUST WASHER 34 1438442 2 MACHINE BUSHING 35 00034300 2 RETAINING RING 2007 Alamo Group Inc. Parts Section 73
LIMITED WARRANTY 1. LIMITED WARRANTIES 1.01.M&W warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser ( Purchaser ) and warrants for six months to the original commercial or industrial purchaser ( Purchaser ) that the goods purchased are free from defects in material or workmanship. 1.02.Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship. 1.03.This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal combustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically found in your Operator s Manual. 1.04.Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any nature on behalf of Manufacturer. 2. REMEDIES AND PROCEDURES. 2.01.This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer within 30 days of purchase. 2.02.Purchaser claims must be made in writing to the Authorized Dealer ( Dealer ) from whom Purchaser purchased the goods or an approved Authorized Dealer ( Dealer ) within 30 days after Purchaser learns of the facts on which the claim is based. 2.03.Purchaser is responsible for returning the goods in question to the Dealer. 2.04.If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and service due to defects in material or workmanship, Manufacturer will: (a) (b) Repair or replace the defective goods or part(s) or Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer) if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty by Manufacturer. The choice of remedy shall belong to Manufacturer. 2.05.Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s) from the Dealer to the designated factory. 3. LIMITATION OF LIABILITY. 3.01.MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. 3.02.MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR USE OF THE GOODS. 3.03.EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOT LIMITED TO, ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROM THE USE OR OPERATION OF THE GOODS OR ANY BREACH OF THIS WARRANTY. NOT WITHSTANDING THE ABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER S LIABILITY HEREUNDER FOR DAMAGES INCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE GOODS. 3.04.NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS OCCURRED. 4. MISCELLANEOUS. 4.01.Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County, Texas. 4.02.Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a waiver of any other term. 4.03.If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such provision shall not invalidate any other provisions herein. 4.04.Applicable law may provide rights and benefits to purchaser in addition to those provided herein. KEEP FOR YOUR RECORDS M&W ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine identification when applying for warranty. M&W Implement Model Serial Number Date Purchased Dealer ATTENTION: READ YOUR OPERATOR'S MANUAL M&W An Alamo Group Company 1020 South Sangamon Ave. Gibson City, Illinois 60936 217-784-4261
TO THE OWNER/OPERATOR/DEALER To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the information you need. The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety requirements of tractor operators: REQUIRED OF THE OWNER: 1. Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and 2. Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C; and 3. Ensure that each employee uses such Seatbelt while the tractor is moving; and 4. Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the protected area provided by the ROPS. REQUIRED OF THE OPERATOR 1. Securely fasten seatbelt if the tractor has a ROPS. 2. Where possible, avoid operating the tractor near ditches, embankments, and holes. 3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces. 4. Stay off slopes too steep for safe operation. 5. Watch where you are going - especially at row ends, on roads, and around trees. 6. Do not permit others to ride. 7. Operate the tractor smoothly - no jerky turns, starts, or stops. 8. Hitch only to the drawbar and hitch points recommended by the tractor manufacturer. 9. When the tractor is stopped, set brakes securely and use park lock, if available. Keep children away from danger all day, every day... Equip tractors with rollover protection (ROPS) and keep all machinery guards in place... Please work, drive, play and live each day with care and concern for your safety and that of your family and fellow citizens.
Round Balers Pub 09-01 Printed U.S.A. P/N 4903WP