Diesel & Biodiesel Testing Solutions Laboratory Instruments for quality control, analysis and calibration

Diesel & Biodiesel Testing Solutions Laboratory Instruments for quality control, analysis and calibration

Diesel & Biodiesel Testing Solutions Flash Point PM-93 Pensky-Martens Closed Cup Flash Point Tester (35000-0) ASTM D93 Procedures A, B and C; EN ISO 2719; IP 34 Strict conformance to international test methods Easy 3-step to test operation involving minimal operator intervention Unique SafeFlash fire extinguishing system Large touch screen Single action lifting pod Small, compact footprint Seta Ignite - robust and long lasting ignitor 30 programmable test profiles, test methods & sample names Rapid fan assisted cooling Optional barcode reader available The Seta PM-93 is a fully automated Pensky-Martens Closed Cup Flash Point Tester which combines strict method conformance with state of the art control technology and safety systems to provide the next generation of automated precision flash point instruments. View a demo video at: www.stanhope-seta.co.uk/4756/pm-93-pensky-martens-flash-point-tester 35000-0 82000-0 Setaflash Series 8 ActiveCool Closed Cup Tester (Flash/No Flash & Ramp Modes) ASTM D3278; ASTM D3828; ASTM D7236; ASTM E502; IP 523; IP 534; ISO 3679; ISO 3680 (obs) Corrosion Resistant cup option Electric ignitor (with gas option) Automatic dipping and flash detection ActiveCool electronic Peltier cooling 64 Test memory & RS232 interface 2 or 4ml sample Barometric pressure correction View a demo video at: www.stanhope-seta.co.uk/setaflash.html Seta Part No: 82100-0 82150-0 82000-0 Temperature Range: Air: 10 to 130 C (50 to 266 F) Air: 10 to 130 C (50 to 266 F) Ambient +5 to 300 C (Ambient +9 to 572 F) Water Assisted: -20 to 130 C (-4 to 266 F) Water Assisted: -20 to 130 C (-4 to 266 F) Test Modes: Rapid Equilibrium and Ramp Rapid Equilibrium and Ramp Rapid Equilibrium and Ramp Sample Size: 2 or 4ml according to method 2 or 4ml according to method 2 or 4ml according to method Test Duration: (Rapid Equilibrium Mode) FAME 1 minute or user defined 1 to 99 minutes FAME 1 minute or user defined 1 to 99 minutes FAME 1 minute or user defined 1 to 99 minutes Ramp Rate: 2 C/min ramp 2 C/min ramp 2 C/min ramp Cup material: Aluminium Corrosion resisting steel Aluminium Heating/Cooling Method: Peltier Cell Peltier Cell Ceramic Pad, Forced Air (post-test cooldown) 25 x 34 x 38cm / 8kg 25 x 34 x 38cm / 8kg 25 x 34 x 38cm / 8kg Setaflash Series 3 (Rapid Equilibrium And Ramp Tests) ASTM D3278; D3828; D7236; IP 523; IP 534; ASTM E502; ISO 3679; ISO 3680 (obs) ActiveCool Sub-Ambient Tests and Rapid Cool Down Temperature range 10 to 130 C or Ambient to 300 C (Depending on model) Rapid Equilibrium and Ramp tests Corrosion Resistant option 1 Minute Flash / No Flash and Actual Flash Point 2/4ml Sample Size View a demo video at: www.stanhope-seta.co.uk/setaflash.html 30000-2 Seta Part No: 33200-2 ActiveCool 33250-2 ActiveCool 33000-2 30000-2 Temperature Range: 10 to 130 C (50 to 266 F) 10 to 130 C (50 to 266 F) Ambient to 300 C (572 F) *(0 to 300 C with coolant module) Ambient to 300 C (572 F) *(0 to 300 C with coolant module) Test Modes: Rapid Equilibrium and Ramp Rapid Equilibrium and Ramp Rapid Equilibrium and Ramp Rapid Equilibrium Sample Size: 2 or 4ml according to method 2 or 4ml according to method 2 or 4ml according to method 2 or 4ml according to method Test Duration: (Rapid Equilibrium Mode) FAME 1 minute or user defined 1 to 99 minutes FAME 1 minute or user defined 1 to 99 minutes FAME 1 minute or user defined 1 to 99 minutes FAME 1 minute or user defined 1 to 99 minutes Ramp Rate: 2 C/min ramp 2 C/min ramp Variable up to 5.5C/min ramp Cup material: Aluminium Corrosion resisting steel Aluminium Aluminium 26 x 28 x 26cm / 5kg 26 x 28 x 26cm / 5kg 26 x 28 x 26cm / 4kg 26 x 28 x 26cm / 4kg 2

Laboratory instruments for quality control, analysis and calibration Oxidation Stability Seta Oxidation Bath (16900-6) ASTM D2274; ASTM D7462; ISO 12205; IP 388 Ambient +5 C to 100 C temperature range 6 position oil bath Digital thermostir unit Seta Oxflo Controller & 6 flowmeters included Low liquid protection and over temperature cut out The Seta Oxidation Bath comprises of a 35 litre oil bath which can accept up to six sets of glassware. A Seta Oxflo control unit includes a gas inlet pressure regulator, pressure gauge and six precision flowmeters calibrated for oxygen at 3 litres/hour, 21 C and 0.4 bar pressure. Visit: www.stanhope-seta.co.uk/4462/oxidation-bath-with-oxflo-controller 16900-6 TOST Dry Block Bath 12 test stations (16640-0): www.stanhope-seta.co.uk/3478 TOST Dry Block Bath 6 test stations (16645-0): www.stanhope-seta.co.uk/3843 Seta 6 Way Window Oil Bath & Oxflo (16960-2): www.stanhope-seta.co.uk/4471 Seta Part No: 16640-0 16645-0 16900-6 16960-2 Window Bath Test Stations: 12 6 6 6 Temperature Range: Ambient to 100 C Ambient to 100 C Ambient +5 C to 120 C Ambient +5 C to 120 C Temperature Control @ 95 C: Uniformity 0.1 C Stability 0.03 C Uniformity 0.1 C Stability 0.03 C Uniformity 0.1 C Stability 0.1 C Uniformity 0.1 C Stability 0.1 C Bath Type: Solid Block Solid Block Oil Filled Oil Filled Bath Capacity: n/a n/a 35 Litres 35 Litres Power: 2Kw 2Kw 1.5Kw 1.5Kw Voltage: 220/240V, 60/60Hz 220/240V, 60/60Hz 110/120V, 50/60Hz, 220/240V 50/60Hz 110/120V, 50/60Hz, 220/240V 50/60Hz Size (HxWxD): Bath: 50 x 25 x 64cm Oxflo Control Unit: 44 x 35 x 26cm Bath: 50 x 25 x 64cm Oxflo Control Unit: 44 x 35 x 26cm Bath: 64 x 36 x 33cm Oxflo Control Unit: 44 x 35 x 26cm Bath: 64 x 36 x 33cm Oxflo Control Unit: 44 x 35 x 26cm Weight: Bath: 110kg Oxflo Control Unit: 11kg Bath: 80kg Oxflo Control Unit: 11kg Bath: 15kg Oxflo Control Unit: 11kg Bath: 15kg Oxflo Control Unit: 11kg Corrosion Seta Ag-Cu Corrosion Bath (11300-2) ASTM D130-IP 154; EN ISO 2160 Copper/Silver Corrosion tests 2 test stations Small footprint Integral circulation plate Safety feature for over temperature Rapid heating Seta s Copper Corrosion Bath is a stainless steel water or oil bath digitally temperature controlled to ±0.1 C over a temperature range of ambient +5 C to 120 C. The bath has two test stations, each with a lid and hook for suspending either a copper corrosion pressure test vessel or a test tube support. A circulation plate is fitted internally to assist in producing an even temperature throughout the bath. Due to the size of the bath and efficient heating system, high temperature can quickly be achieved. Visit: www.stanhope-seta.co.uk/4440/seta-ag-cu-corrosion-bath Silver & Copper Corrosion Bath 9 station (11400-7): www. stanhope-seta.co.uk/4444 Seta Copper Silver Block Bath (11310-0): www.stanhope-seta.co.uk/4951 Seta Part No: 11300-2 11400-7 Test Stations: 2 9 Temperature Range: Ambient +5 C to 120 C Ambient +5 C to 150 C Temperature Stability: ±0.1 C ±0.1 C Bath Fluid: Water or Oil Water or Oil Bath Capacity: 18 Litres 35 Litres Heater Power: 1200W 1500W 52 x 34 x 23cm / 9kg 52 x 45 x 33cm / 10kg 11300-2 3

Diesel & Biodiesel Testing Solutions Filter Blocking Tendencies Seta Cold Filter Blocking Tester (91670-2) ASTM D2068, IP 387, IP 618 Fully compliant to national annex to BS EN 590 Automatic calculation of CFBT and CSCFBT Portable design Easy to use, fully automated Fixed and programmable temperatures Typical 20 min test time for 2 temperatures The Seta CFBT is a small scale laboratory analyser which measures the Cold Filter Blocking Tendency (CFBT) of diesel and gas oils. The CFBT predicts how diesel fuel may behave at low ambient temperatures by replicating vehicle/engine field cold conditions and testing the fuel s filter tendency. Visit: www. stanhope-seta.co.uk/5426/seta-cold-filter-blocking-tester-(cfbt-&-cscfbt) 91670-2 Seta Multi Filtration Tester (91600-3) ASTM D2068; IP 387 (A, B); ASTM D7501; IP PM-EA Cold Soak Test Method for EN 590 Biofuel and EN 14214 FAME material; CEN N 403 Portable test for filterability/blocking tendency Test parameters for IP 387 and ASTM D2068 test are pre-programmed Automatic calculation of FBT and F-QF Simple calibration/verification of flow, pressure & temperature Compact and easy to use Result in less than 15 mins Interface for PC or Printer CFBT Pump Rate: Sample Size: Temperature Range: 20ml/min adjustable in software 750ml -5ºC to +40ºC 35.5 x 52 x 54cm / 15kg The MFT is a unique instrument designed to test the Filter Blocking Tendency (FBT) of diesel, biodiesel (B100 & B5/7/20/30), gas oil, gas turbine fuel and kerosene. Test parameters for IP 387 and ASTM D2068 are pre-programmed. FBT analysis is achieved by measuring the pressure differential across a disposable filter. Fuels which have a high FBT could potentially block filters in the distribution network or during use in a vehicle or power plant. The MFT is also used to determine the FBT for Biofuels which have been cold soaked at a temperature just above zero Celsius. During the 16 hour cold soak particles of saturated monoglycerides and sterol glucosides can be formed which do not dissolve when the temperature is raised back to ambient. The MFT procedure is able to detect fuels containing these particles. For further details please see the Cold Soak Test bath below. PC software is available which enables the pressure versus time plots to be stored dynamically, compared against one another and output in a variety of formats to enable data analysis in Excel for example. Visit: www. stanhope-seta.co.uk/3895/seta-multi-filtration-tester-(mft) FBT Verification Material (91668-0) Used to check calibration of the MFT, including verification of filters, according to IP 387 Procedure B and as referenced in IP PM-EA and CEN N 403. The methods recommend use of a certified verification fluid with a nominal FBT of 2.00, a certificate stating the precise value is supplied with the verification material. MFT Filter Blocking Tendency (FBT) Range: Maximum Pressure: Power Requirement: 1.0 to 30 (low number best) 200kPa 110/120Vac or 220/240Vac (switchable) 27 x 43 x 26cm / 10kg 91600-3 Seta Cold Soak Test Bath (91665-0) ASTM D7501; IP PM-EA; CGSB-3.0 No 142; CEN N 403; ASTM D6751; EN 14214 4 x 500ml Sample Bottle Capacity Pre-programmed Cold Soak test conditions Automatic warm up after 16 hours Integral Cooling and Heating, -20 to +80 C Suitable for pre-conditioning samples at 60 C View a demo video at: www.stanhope-seta.co.uk/cold-soak.html IP PM-EA, CEN N 403: +5 C for 16 hours 20 C for 2 hours ASTM D7501: +4.5 C for 16 hours 25 C for 2 or 4 hours CGSB-3.0: +1 C for 16 hours 25 C for 2 hours Temperature: Range: Temperature: Stability: Bath Liquid Capacity: Refrigerant: -20 to +80 C (-4 to +176 F) ±0.02 C 12 litres CFC free, Single Stage R507 Cool down time: Approx. 45 minutes from 25 to 1 C Ambient Temperature range: 15 to 30 C 91665-0 78 x 32 x 51cm / 46.6kg 4

Laboratory instruments for quality control, analysis and calibration Water and Sediment Seta Oil Test Centrifuge for Sediment & Water ASTM D1796; D2709 Heated chamber, ambient to 80 C Static, near vertical bucket positioning 4 or 6 place swing out rotor Membrane touch control panel Pre-heat facility to ensure bowl is at test temperature prior to test Conforms to IEC 1010-1 & 1010-2-D safety requirements With a temperature range of 30 to 80 C and a rotational speed of up to 3000rpm, this heated chamber centrifuge is specifically designed for testing oils. The large diameter chamber, with four or six place rotor and cushioned adaptors, allows the use of 6 and 8 inch conical, pear-shaped, trace sediment and 12.5ml tubes as specified by the various test methods. The swing out rotor ensures that the samples are held near vertical when at rest allowing more precise measurement of sediment. An optional hazard reduction system extracts vapours and gases released from volatile samples. Visit: www.stanhope-seta.co.uk/3943/seta-oil-test-centrifuge 6 place Centrifuge is also available (90100-0) Visit: www.stanhope-seta.co.uk/4807/seta-6-oil-test-centrifuge Centrifuge Tubes Centrifuge Tubes 100ml Long & Short Cone, Trace Sediment, and 12.5ml Finger Tubes Manufactured in strict compliance to test methods Permanently etched graduations High visibility white lined markings Optional factory certified, 7 point, long cone tubes Product Reference: 4 place Centrifuge (90000-3) or 6 place Centrifuge (90100-0) Maximum RCF: 2214g Maximum RPM: 3000 Temperature Range: 30 to 80 C (± 1 C) (86 to 176 F) Timer Range: 1 to 60 minutes in 1 minute steps, Continuous Operation Rotor Capacity: 4 or 6 place samples (order reference 90100-0 for 6 place) Power Requirement: 230Vac (110V transformer option) 50/60Hz / 1kW 40 x 56 x 64cm / 86kg 90000-3 Ash Seta Ash Furnace (99220-2) ASTM D482-IP 4; ISO 6245; EN 7; ISO 3987 Pre-heated airflow system & extended chimney Maximum temperature 1100 C with over-temperature cut-out Door safety power cut off switch Features a digital temperature controller The Seta Ash Furnace has a maximum temperature of 1100 C, it incorporates pre-heated airflow system and extended chimney. The furnace is supplied with an Inconel tray complete with a detachable handle, it features a door safety power cut-off switch as well as an over-temperature cut out protection. The chambers of the furnace are ceramic muffles wound with resistance wire. Visit: www.stanhope-seta.co.uk/4038/seta-ash-furnace Capacity: Chamber Size (HxWxD): Size (HxWxD): 7 Litres 9 x 17 x 46cm 65 x 43 x 74cm / 63kg 99220-2 5

Diesel & Biodiesel Testing Solutions Conductivity Handheld Conductivity Meter (99708-0) ASTM D2624; IP 274 Higher accuracy AC measurement (± 1.5% of reading) Conductivity and temperature output capability Measure in any sample container No need to relax the fuel Calibration kit available Stores up to 8 data locations USB interface for ease of data transfer to user Fully temperature compensated measurement The Seta D2 Hand Held Conductivity Meter (D2 JF-1A-HH model) meets the requirements of ASTM D2624. It provides an accurate and rapid conductivity measurement of distillate fuels; and is specifically designed for testing low conductivity fluids such as such as aviation kerosene, ULSD, home heating fuel, Naphtha, and printing ink. The meter can measure fuel electrical conductivities between 0 and 2000 picosiemens/meter (ps/m), although it is optimised and normally used in the 0 to 500 ps/m range. Other ranges are available on request to measure lubricity oil and inks. Visit: www.stanhope-seta.co.uk/3963 99708-0 with accessories Conductivity Meter for Fuels (99708-0) 0-2000 ps/m ±2 ps/m (±1.5% of reading) Conductivity Meter for Lubricity Oils (99707-0) 0-2000 ps/cm ±1.5 ps/cm (±1.5% of reading) Conductivity Meter for Ink & Paints (99706-0) 0-10,000 ps/cm ±1 ps/m (±1.5% of reading) Resolution: 0.1 ps/m (99708-0), 0.1 ps/cm (99707-0) Temperature Range: 0 to 35 C (±0.1 C) (32 to 95 F) 31 x 11 x 10cm / 0.5kg Conductivity Calibration & Verification Tool (99714-0) The Calibration & Verification tool fits easily onto the tip of the Handheld Conductivity Meter for quick and easy calibration or verification of the instrument. It has one switch to easily alter the range from low value (200 ps/m) to high value (500 ps/m). This allows the user to verify or calibrate conductivity in the field thus eliminating the costly requirement of returning the instrument to the factory. The tool is optimised for AC conductivity measurement with active components ensuring long term stability and accuracy. Visit: www.stanhope-seta.co.uk/4663/calibration-kit-for-handheld-conductivity-meter 99708-0 & 99714-0 Distillation Setastill Distillation (11860-3) ASTM D86; IP 123; ISO 3405 Ambient to 400 C distillation range Adjustable height heater/flask platform Toughened glass window Cooling fan The distillation unit, mounted to the left, comprises a flask support mechanism, heater elements, and the heater controller. The flask is supported by a drop-in ceramic-glass support board mounted to a platform that is adjustable for height. The quartz enclosed heating elements are also attached to the platform, and are powered by a solid-state energy regulator and calibrated control. A cooling fan is installed in the rear of the distillation unit to reduce cooling time between distillations. The condenser unit is attached to the distillation unit, and may be used with either a static fill of coolant or a laboratory cooling supply. Visit: www.stanhope-seta.co.uk/3391/setastill-distillation 11860-3 6

Laboratory instruments for quality control, analysis and calibration Carbon Residue Micro Carbon Residue Tester (97400-3) ASTM D4530; IP 398; ISO 10370; Carbon Residue (Micro Method) Carbon residue range 0.1% to 30.0% (m/m) Fully automatic Digital bar graph for precise gas control Precise and automatic temperature ramp and gas flow control Large 18mm display digits Very easy setup The Seta Micro Carbon residue tester is an automatic instrument designed to run tests to determine the carbon residue formed after evaporation and pyrolysis of petroleum products as per ASTM and IP test methods. The instrument comprises of an oven and insulating lid with curved top plug as defined in ASTM D4530 and IP 398. Nitrogen gas purging and temperature RAMP sequences are fully automatic and no operator intervention is required when running the test. A digital mass flow meter and high precision temperature control system ensure compliance to the methods. Visit: www.stanhope-seta.co.uk/4882/micro-carbon-residue-tester Temperature Range: Ramp Rate: Thermocouple: Pressure controller: Primary pressure: Flowmeter: Flow Rate: Ambient to 500 C ±2 C 10 to 15 C/min Iron-constanton 20 to 700kPa 1000kPa max 0.1 to 1 litre/min Automatic, 150ml/min or 600ml/min 46 x 35 x 39cm / 21kg 97400-3 Filtration Kits Seta Reference 19720-0 Filtration Kit for Determining Contamination in Middle Distillates Test Method IP 440; EN 12662 19724-0 Filtration Kit for Testing Middle Distillates ASTM D6217; IP 415 Visit: www.stanhope-seta.co.uk/3399/filtration-kit-for-ip-440;-en-12662 www.stanhope-seta.co.uk/3774/filtration-kit-for-astm-d6217,-ip-415 19724-0 Total Sediment Setaclean Total Sediment Tester (16120-2) ASTM D4870-IP 375; IP 390 (Procedure A); ISO 10307 Measures sediment up to 0.5%m/m Sample viscosities up to 130m/m 2 /S 10g sample size Two test stations A compact bench-mounted unit for determining the insoluble material content of distillate and residual fuel oils. Visit: www.stanhope-seta.co.uk/752/setaclean-total-sediment-tester Capacity: Chamber Size (HxWxD): Size (HxWxD): 7 Litres 9 x 17 x 46cm 65 x 43 x 74cm / 63kg 16120-2 7

Viscosity KV-6 Viscometer Bath (84200-3) ASTM D445-IP 71; ASTM D446; BS 188, BS 2000 Parts 71 & 319; DIN 51 366; DIN 51 562; EN 3104; FTM 791 305; ISO 3105; JIS K2283; NF T60-100; NF T60-136 Easy accessible drain valves 50 litre bath capacity minimising temperature recovery time Integrated heating and stirring system Stainless steel internal components providing long term durability Two positions for reference thermometers Digital display with 0.01 C resolution Toughened glass front panel Integral back lighting Diesel & Biodiesel Testing Solutions The Seta KV-6 has a 50 litre temperature controlled bath that can accommodate up to six standard viscometer tubes. Digital temperature control and an inbuilt cold water cooling coil provide accurate and stable test temperatures from ambient to 150 C. The bath is protected by low liquid level and over temperature cut-outs. The bath is equipped with a toughened glass front window, easily accessible drain valve, integral back lighting, top plate, and provision for reference thermometer and attachments. Visit: www.stanhope-seta.co.uk/5406/kv6-viscometer-bath 84200-2 Temperature Range: Ambient to 150 C (302 F) Temperature Stability: ±0.002 C at 40 C, ±0.005 C at 100 C, ±0.01 C at 150 C Temperature Uniformity: ±0.003 C at 40 C ±0.006 C at 100 C Tube Capacity: Up to 6 Bath Fluid: Oil, silicone fluid or water Bath Capacity: 50 Litres 68 x 56 x 33cm / 33kg Cloud and Pour Point Seta Cloud and Pour Point Cryostat (93531-7) ASTM D97; IP 15; ISO 3016; FTM 791 201; Pour Point of Petroleum Products ASTM D2500; IP 219; ISO 3015; Cloud Point of Petroleum Products Four Individually temperature controlled compartments Four air wells in each compartment Ambient to -51 C CFC free refrigeration system Heated anti-condensation lid The Seta Cloud and Pour Point Cryostat is a floor standing unit with four independently temperature controlled compartments each accommodating four Air Wells. The lid is electrically heated to prevent the formation of ice and condensation. Visit: www.stanhope-seta.co.uk/3892/seta-cloud-and-pour-point-cryostat Seta Compact Cloud & Pour Point Cryostat (94100-3) ASTM D97; IP 15; ISO 3016; FTM 791 201; Pour Point of Petroleum Products ASTM D2500; IP 219; ISO 3015; Cloud Point of Petroleum Products Four Individually temperature controlled compartments Four air wells in each compartment Ambient to -34 C CFC free refrigeration system Heated anti-condensation lid Visit: www.stanhope-seta.co.uk/3891/seta-compact-cloud-and-pour-point-cryostat 93531-7 Seta Part No: 93531-7 94100-3 Total Test Positions: 16 12 Compartment Volume: 2 Litres 2 Litres Temperature Range: Ambient to -51 C Ambient to -34 C Cool Down Time: Approximately 2 hours Approximately 1 hour Refrigerant: CFC Free: First Stage R134a Second Stage: R507 CFC Free: First Stage R507 95 x 63 x 63cm / 115kg 60 x 60 x 85cm / 115kg Cold Filter Plugging Point (CFPP) Apparatus ASTM D6371; IP 309; EN 116 Determines low-temperature flow characteristics of diesel fuels, gas oils and other distillate fuels Compatible with fuels containing flow improving additives Visit: www.stanhope-seta.co.uk/4734/cold-filter-plugging-point-(cfpp)-apparatus 8 t: +44 (0) 1932 564391 f: +44 (0) 1932 Stanhope-Seta, 568363 e: London sales@stanhope-seta.co.uk Street, Chertsey, Surrey, www.seta-analytics.com KT16 8AP, UK

Laboratory instruments for quality control, analysis and calibration Particulates Seta AvCount2 Laser based Particle Counter (SA1000-2) ASTM D7619; ASTM D975 Particle size ISO 11171: 4μm(c) to >70μm(c); ISO 4402: 2μm to >100μm; GOST 17216: 2μm to >200μm Cumulative & distributive particle counts Cleanliness code reporting Uses Straight from the Bottle samples Precise and reliable results Rugged case suitable for laboratory or portable use Typical test time of less than 6 minutes 16 fixed measuring channels (calibration in compliance with ISO 11171 for measuring in oil) An upper and lower limit value can be set for each of the first 6 counting channels Data storage for up to 2300 measurements across 64 memories Internal Double Pump System downstream of measurement cell Optional in-line high pressure testing up to 315 Bar AvCount2 is fully automatic once the particle count test sequence is started. The instrument flushes the cell with sample prior to commencing the measurements. A precise volume of sample is then analysed. The flushing / sample analysing sequences are automatically repeated in accordance with the selected test method. Results are displayed on the LCD screen in real time and printed out on the integral printer as the test progresses. The results are shown for 6 particle size bands in Particles/ml and ISO Code. Results can be saved to memory for trend analysis of samples, printed out on the integral printer or downloaded to a USB memory stick. View a demo video at: www.stanhope-seta.co.uk/4161/avcount2-particle-counter Counts per Measurement (max): 600.000 (60.000 p/ml) Sample Viscosity (max): 64mm 2 /s (from sample bottle) Sample Temperature Range: 0 to 80 C Results: Measurement Volume: Flow Rate: Voltage: Power: Computer interface: SA1000-2 Particles/ml or Particles/10ml (Test Method dependant), Cleanliness Codes, Cumulative and/or Distributive (Test Method dependant) 10ml 30ml/min 100 to 250v 50/60 Hz or 24Vdc 30W USB A (for memory sticks), USB B and RS232 20 x 35 x 24 cm / 12kg Seta AvCount Lite Laser based Particle Counter (SA1800-0) ASTM D7619; ASTM D975 Cumulative Particles/ml ISO Cleanliness Codes Simple operation High visibility screen Portable Optional battery Bottle sample or On-Line Stand-alone or PC controlled Programmable via PC Volume or Time based Under three minute test time for D6719 SA1800-0 AvCount Lite is the latest fully automatic particle counter from Seta Analytics. The new instrument combines innovative features and rapid measurement technologies to make the Avcount Lite the most flexible particle counter available. Avcount Lite can be used as a stand-alone instrument or connected to a PC workstation for operation. Multiple instruments can be monitored from a single PC and linked to allow trend analysis, for example monitoring particulate before and after a filter. When used as a stand-alone instrument, the Avcount Lite is small and ideal for field use, operation is via a simple menu system using the turn and push control. Test progress and results for up to 6 size bands are displayed as cumulative particles/ ml and ISO 4406 cleanliness codes on the high visibility yellow and black screen. Results are saved in memory indexed by date and time. Method compliance is assured, and the Avcount Lite is in full compliance with all relevant standards as well as ASTM D7619. Optional PC software allows creation and modification of customised standards for specific applications. Visit: www.stanhope-seta.co.uk/avcount_particle_counting.asp Product Number: SA1800-0 Counts per measurement (max): 600.000 (60.000 p/ml) Sample Viscosity (max): 64mm 2 /s Test methods: 3 stored at any one time, unlimited on PC Pre-programmed: ASTM D7619 and ISO 4406 basic Number of Measuring channels: 6 (stand alone), 15 (PC) programmable Results: up to 600 internal, unlimited on PC Automatic: Fully automatic with auto averaging Software: PC software available Connectivity: USB Connection to a PC Voltage: 12Vdc, 1A Power: Charger/Mains Adaptor 100 to 230VAC, 50/60Hz, 650mA 25 x 33 x 15 cm / 9kg Calibration: ISO 11171 Stanhope-Seta, t: +44 (0) 1932 564391 London Street, f: +44 (0) Chertsey, 1932 568363 Surrey, e: KT16 sales@stanhope-seta.co.uk 8AP, UK www.seta-analytics.com 9

Cetane AFIDA Cetane Number Analysis (SA6000-0) IP 617; Pr EN 17155; ASTM DXXXX; EN 590 5.7.4 Direct correlation to ASTM D613 (ISO 5165) CFR engine tests Bench top operation Fully automated measurement Very small sample volumes (approx 40 ml/analysis including flushing) Short analysis time of approximately 20 minutes per sample Integral 36 place carousel and auto sampler Minimum operator time Precise and reproducible software-controlled determination of CN Calibration with industry approved PRFs Advanced electronically controlled high pressure fuel injection system Diesel & Biodiesel Testing Solutions Diesel & Biodiesel Testing Solutions Developed by Analytik-Services Gesellschaft (ASG) the Advanced Fuel Ignition Delay Analyser (AFIDA) represents the latest generation technology for the Cetane Number measurement of diesel and related fuels using the constant volume combustion chamber principle (CVCC). AFIDA provides fully automated determination of the Indicated Cetane Number ICN of diesel and diesel related fuels. The Analyser incorporates a unique and patented high pressure injection system that generates fine fuel droplets similar to modern common rail injectors that are currently applied in the automotive industry. The Analyser provides very fast, efficient and calibrated CN determinations, tests are fully automated via an integral carousel and auto sampler. Visit: www.stanhope-seta.co.uk/ 5061/AFIDA---Advanced-Fuel-Ignition-Delay- Analyser Chamber temperature: 580 C Analysis time: Approx 25 min/sample Carousel Capacity: 36 samples Chamber pressure: 17.5 bar Injection pressure: 1000 bar SA6000-0 Hydrogen Sulfide H 2 S Analyser with Vapour Phase Processor (VPP) TM (SA4000-3 & SA4015-0) ASTM D7621; IP 570; ISO 8217:2010 Marine Fuel Specification Measurement range from 0-250 mg/kg H 2 S (0-250 ppm H 2 S) in the liquid phase Vapour Phase Processor proven to eliminate effects of chemical interference A non chemical method, no wet chemistry involved Small lab bench footprint, fully portable operation Suitable for monitoring residual marine fuel blends, distillate fuels, refinery feedstock components, cargoes & products in the distribution system and crude oils Critical Measurement method for Product Safety and Release Compressed air: 20.9 ± 0.5 % O 2 Sample volume Approx. 40 ml for analysis and cleaning Range for ICN 35 85 130 x 80 x 60cm / 100 kg The H 2 S Analyser was developed with Lloyd s Register s Fuel Oil and Bunker Analysis Service (FOBAS) along with support of other major international oil companies to offer rapid measurement of H 2 S in petroleum products. The VPP accessory was subsequently developed to eliminate the effects of chemical interference and to enable the analyser to address a broader range of petroleum products. IP 570 Procedure A (with VPP) is now the industry recommended practice for measuring marine residual fuels and blend streams. The H 2 S Analyser is an excellent tool for supporting product Quality Control and safety ensuring product is within approved specification. It is also ideal for both product remediation treatment of feedstock components and off-spec products with fast repeat sample measurement capability. H 2 S is efficiently purged from the test sample by a combination of heat and agitation, and is measured by an advanced electrochemical sensor. The instrument offers a cost effective solution for H 2 S measurement no costly chemicals are required and there is no need for analytical preparation by an expert chemist. The Crude Oil Test Kit (SA4021-0) allows the H 2 S Analyser to be used with the Vapour Phase Processor for testing Crudes, in accordance with ASTM D7621 Appendix X1. View a demo video at www.stanhope-seta.co.uk/4909/h2s-analyser H 2 S Product Number: VPP Product Number: IP 570 PTS: Crude Oil Test Kit: SA4000-3 SA4015-0 SA4030-0 (3 months), SA4031-0 (12 months), SA4032-0 (quarterly) SA4021-0 H 2 S Analyser range: 0-250 mg/kg H 2 S in the liquid phase (0-250 ppm H 2 S) Viscosity Range: Up to 3000 mm 2 /s Principle of measurement: Test duration: Sample size: Diluent volume: H 2 S VPP Advanced Electrochemical sensor 25 minutes with VPP 1ml, 2ml, 5ml (depending on H 2 S concentration) 20ml SA4000-3 & SA4015-0 21 x 30 x 41 cm / 8kg 40 x 24 x 20 cm / 7.8kg 10 10 t: +44 (0) 1932 564391 f: +44 (0) 1932 568363 Stanhope-Seta, e: sales@stanhope-seta.co.uk London Street, Chertsey, www.seta-analytics.com Surrey, KT16 8AP, UK

Aromatics Evochrom Aromatics HPLC System (SA2400-3) ASTM D6591; IP 391; EN 12916 ASTM D6379, ASTM D6591, EN 12916, IP 391, IP 436 Complete HPLC system allows plug and go for the busy lab Precision engineered HPLC hardware with proven technology Chromatography assured with optimised column technology meeting the latest ASTM & IP Method requirements Quality separations provide accurate and precise results every time Fully compatible to meet and measure to DEF STAN 91-91 Jet Fuel and EN 590 Diesel Fuel Specifications for Aromatics Optional in-line high pressure testing up to 315 Bar Laboratory Instruments for quality control, analysis and calibration Laboratory instruments for quality control, analysis and calibration High performance liquid chromatography (HPLC) measuring mono and di-aromatic hydrocarbon contents in aviation kerosenes and petroleum distillates. Visit: www.stanhope-seta.co.uk/4696/evochrom-aromatics-hplc-system Seta Twin-Column Adsorption Apparatus (14060-0) ASTM D1319-IP 156; ISO 3837 Determines volume % of saturates, olefins and aromatics in petroleum fractions Analyses 2 samples simultaneously Accepts standard adsorption or precision (True Bore) columns Integral UV illumination The Seta Twin-Column Adsorption Apparatus measures Fluorescent Indicator Adsorption in Liquid Petroleum Products. 14060-0 SA2400-3 FAME Content FIJI DRG - Distillate & Residual Fuels (SA5100-0) ASTM D7963, Correlates with EN 14078; ISO 8217 All FAME types from C8 to C22 including Coconut, Mustard, Palm, Rapeseed, Sunflower oil, Soya, Jatropha Suitable for DM, DF and RM grades Analysis time 15 minutes Rapid screening method Certified range 20 mg/kg to 20% in Middle Distillates Laboratory and field instrument Fully automatic Suitable for untrained operators No cleaning solvents required No pre-sample preparation required 50 ml sample volume FIJI uniquely utilises state of the art FTIR (Fourier Transform Infra-Red Spectroscopy) technology and a patented sample preparation system which allows FAME detection to 10mg/kg level. FIJI is robust, extremely simple to use and is fully automatic so no specialist operator training is involved. Tests require less than 50ml of sample and typically take under 20 minutes. Results are presented in mg/ kg units together with an optional traffic light system for flagging FAME contamination levels of the fuel. Using a unique sample preparation module the sample is pumped at a controlled flow rate though a proprietary disposable cartridge. The sample components are spectrally analysed by the FTIR and a result is displayed in mg/kg, a graphical spectrum is also shown. The system is self-cleaning so no solvents are required. After each test the cartridge is simply and easily replaced and the instrument is immediately ready for the next sample. View a demo video at www.stanhope-seta.co.uk//4915/fiji-drg---fame-in-distillate-&-residual-fuels SA5100-0 Test Method: ASTM D7797; IP 583 ASTM D7963 ASTM D7963; ASTM D7797; IP 583 Product Number: SA5000-2 FIJI FAME in Jet Instrument SA5100-0 FIJI DRG - Distillate & Residual Fuels SA5200-0 FIJI MultiFuel - Aviation, Distillate & Residual Fuels Fuel Option(s): AVTUR (Aviation Fuel) Middle distillate & residual AVTUR & Middle distillate and residual Sample size: 50ml 50ml 50ml Certified Range: 10-150 mg/kg 20 mg/kg to 20% Aviation: 10-150 mg/kg Middle distillate & residual: 20 mg/kg to 20% Measurement Range: 0-150 (mg/kg) 0 mg/kg to 20% Aviation: 0-150 (mg/kg) Middle distillate & residual: 0 mg/kg to 20% Stanhope-Seta, t: +44 (0) 1932 564391 London Street, f: +44 Chertsey, (0) 1932 568363 Surrey, KT16 e: sales@stanhope-seta.co.uk 8AP, UK www.seta-analytics.com 11

Diesel & Biodiesel Testing Solutions Diesel EN 590 Diesel ASTM D975 Fuel Oil ISO 8217 Bio-Heating Fuels EN 14213 Bio-Auto Fuels EN 14214 Bio-Fuel Blend Stock B100 ASTM D6751 Instrument Seta Reference Number Flash Point EN ISO 2719 ASTM D93 ISO 2719 EN ISO 3679 EN ISO 3679 ASTM D3828 Automatic / Manual Pensky Martens Setaflash Series 3 Range Setaflash Series 8 Range 35000-0 / 13661-4 Series 3 Series 8 Oxidation Stability ASTM D2274 ISO 12205 Oxidation Bath TOST Bath TOST Dry Block Bath 6 Way Window Oil Bath 16900-7 16640-0 16645-0 Corrosion EN ISO 2160 ASTM D130 EN ISO 2160 ASTM D130 Cu/Ag Corrosion Bath Ag/Cu Corrosion Bath Water and Sediment ASTM D2709 ASTM D1796 ISO 3733 ASTM D2709 4 Place Centrifuge 6 Place Centrifuge 11300-2 11400-7 90000-3 90100-0 Ash EN ISO 6245 ASTM D482 ISO 6245 ISO 3987 ISO 3987 ASTM D874 Ash Furnace 99220-2 Conductivity ASTM D2624 Handheld Conductivity Meter 99708-0 Distillation EN ISO 3405 ASTM D86 Setastill Distillation 11860-3 Carbon Residue EN ISO 10370 ISO 10370 EN ISO 10370 EN ISO 10370 ASTM D4530 Micro Carbon Residue Tester 97400-3 Filter Blocking Tendency IP387 IP 618 Multi Filtration Tester Cold Filter Blocking Tester 91600-3 91670-2 Total Sediment ISO 10307 Setaclean Total Sediment Tester 16120-2 Viscosity EN ISO 3104 ASTM D445 ISO 3104 EN ISO 3104 EN ISO 3105 EN ISO 3104 ASTM D445 KV-6 Viscometer Bath 84200-3 Cloud Point EN 23015 ASTM D2500 ISO 3015 ASTM D2500 Seta Cloud & Pour Point Bath Seta Compact Cloud & Pour Point Cryostat Pour Point ISO 3016 ISO 3016 Seta Cloud & Pour Point Bath Seta Compact Cloud & Pour Point Cryostat 93531-7 94100-3 93531-7 94100-3 Cetane Number AFIDA Cetane Number Analysis SA6000-0 Particulates EN 12662 ASTM D7619 EN 12662 Seta AvCount2 Laser Based Particle Counter Sera AvCount Lite Laser Based Particle Counter SA1000-2 SA1800-0 Hydrogen Sulfide IP 570 H 2 S Analyser with Vapour Phase Processor SA4000-3 & SA4015-0 Aromatics EN 12916 ASTM D1319 Evochrom Aromatics HPLC System Seta Twin-Column Adsorption Apparatus SA2400-3 14060-0 CFPP EN 116 ASTM D6391 EN 116 CFPP Apparatus 99000-3 FAME Content EN 14078 ASTM D7371 EN 14078 ASTM D7963 Seta FIJI DRG Seta FIJI MF SA51000-0 SA5200-0 MULTI TEST VERIFICATION MATERIALS Highly cost effective solution to Laboratory verification requirements Verification to ASTM/CEN/ISO/IP Traceable to ISO 9001 18 Month Validity 99851-0 SETA MTVM - GAS OIL 500ML Test Name ASTM / Method Range Amount/test Density at 15 C D4052-IP 356 0.83 to 0.854kg/l 2ml Distillation IBP D86-IP 123; EN ISO 3405 160 to 190 C 100ml Distillation 10% D86-IP 123; EN ISO 3405 200 to 242 C 100ml Distillation 50% D86-IP 123; EN ISO 3405 255 to 290 C 100ml Distillation 90% D86-IP 123; EN ISO 3405 320 to 350 C 100ml Distillation 95% D86-IP 123; EN ISO 3405 335 to 368 C 100ml Distillation FBP D86-IP 123; EN ISO 3405 347 to 385 C 100ml Distillation Residue D86-IP 123; EN ISO 3405 1.25 to 1.42%vol 100ml Distillation Loss D86-IP 123; EN ISO 3405 0.26 to 0.7%vol 100ml FAME Content IP 579; EN 14078 0.03 to 19.03%(V/V) Flash Point D93-IP 34; EN ISO 2719 56 to 80 C 75ml Cloud Point D2500; D5771-IP 444; -17 to -4 C Up to 38ml D5772-IP 445; D5773-IP 446; IP 219; ISO 3015; EN 23015 CFPP D6371; IP 309; EN 116-30 to 0 C 45ml Pour Point D97-IP 15; D5950; D5949; -33 to -6 C Up to 38ml D6749; D6892; D5985; EN ISO 3016 Kin Vis 40 C D445-IP 71; EN ISO 3104 2.3 to 3.5mm 2 /s Up tp 40ml Lubricity HFRR D6079; IP 450; ISO 12156-1 212 to 512µm 2ml Water Karl Fischer D1744; IP 438; EN ISO 12937 23.4 to 63.9mg/kg 5ml 99852-0 SETA MTVM - FUEL OIL 500ML Test Name ASTM / Method Range Amount/test Density at 15 C D4052-IP 356 0.94 to 0.994 kg/l 2ml Pour Point D97-IP 15-14 to 7 C Up to 38ml Kin Vis 50 C D445-IP 71; EN ISO 3104 150 to 1800mm 2 /s Up to 40ml Kin Vis 100 C D445-IP 71; EN ISO 3104 20 to 95mm 2 /s Up to 40ml Micro Carbon D4530; IP 398; ISO 10370 0.10 to 30.0%(m/m) 2ml Flash Point D93 (b) - IP 34 (b); EN ISO 2719 (b) 88.9 to 121.6 C 75ml MULTI TEST CERTIFIED REFERENCE MATERIALS Certified in accordance with ISO 17025 & ISO Guide 34 Calibration & verification options for laboratory test equipment Multiple test parameters providing flexible & cost effective solutions Highest level of accreditation guarantee, providing credible certified data SP9000-0 MULTI TEST CRM - DIESEL OIL 500ML Test Name Certified Range Cold Filter Plugging Point (Diesel) -16.9 C Cloud Point Standard (Diesel) - 5.8 C Density Standard (Diesel) 0.8355 g/ml @ 15 C Distillation Standard (Diesel) 168.5 C - 360.1 C Flash Point Standard Pensky Martens (Diesel) 57.3 C SP9000-0 Issue Issue 1 2