Catalog number: / / / Mtg. Fixture Electrical Module Finish See page 2 See page 3 Options Pole and Arm Select pole from Kim Arms and Poles Selection Guide. If pole is provided by others indicate O.D. for arm fitting. Approvals: Date: Page: of 5 Specifications LEB9 - Medium Bottom Mount 85 watt 0 32" DIA. " (279.4 mm) 3L" 0 32" " (279.4 mm) 0 32" " (279.4 mm) 4" (0.6 mm) 2L" (69.9 mm) DIA. DIA. (08.0 mm) 3L" (08.0 mm) 3L" (08.0 mm) LEB Bottom Mount Adapter for mounting to arms L" (9. mm) 2K" (37.5 mm) SS Single Straight Arm L" (9. mm) 2K" (37.5 mm) SC Single Curved Arm 3K" (88.9 mm) 2K" (37.5 mm) DC Double Curved Arm Housing: One-piece, die-cast low copper (<0.6% Cu) aluminum alloy components with integral cooling fins. Lens Frame: One-piece, die-cast low copper (<0.6% Cu) aluminum alloy. Stainless steel hinges provided for attachment to housing. The F" thick clear flat or convex tempered glass lens seals against the reflector flange with a one-piece silicone gasket. Flat glass is standard for the horizontal reflector modules and Sag glass is standard for the vertical reflector modules. Optional molded Acrylic or Lexan is available on all versions. Hub: Die-cast, low copper (<0.6% Cu) aluminum alloy with die-cast access cover. Hub is used to support the arm components and for overall support of the luminaire and provides field wiring access. Mounting is to a single pole or a tenon mount for poles by-others. A sand-cast adaptor casting is provided when HA-Arms are specified. Lantern Arm: Single Straight, Single Curved or Double Curved, die-cast, low copper aluminum alloy supports the housing and provides access for wiring. Optional trims are available to compliment the arm styling. Ballast Module: All electrical components are UL and CSA recognized, mounted on a single bracket and factory pre-wired pressed against the ribbed housing wall for maximum heat sinking. Reflector Module: One-piece Specular Alzak aluminum shell. Reflector module hooks in and out of the housing by no-tool release hinges and secures to the housing flange by a quick-disconnect plug. Reflectors are factory pre-wired with a quick-disconnect plug. Electrical Module: All electrical components are UL and CSA recognized, mounted on a single bracket and factory pre-wired with quick-disconnect plugs. A complete HF generator and Induction Lamp system is furnished mounted to the aluminum plate inside housing. Induction Lamp system is high power factor rated for -4 F, starting. Mounting: The fixture is equipped for flush mount (FM), Pole Tenon Mount (PT), or as an arm mount. Finish: Super TGIC thermoset polyester powder coat paint, 2.5 mil nominal thickness, applied over a titanated zirconium conversion coating; 5000 hour salt spray test endurance rating. Standard colors are Black, Dark Bronze, Light Gray, Stealth Gray, Platinum Silver, or White. Custom colors are available. Warranty: Kim Lighting warrants Induction Lighting System luminaires to be free from defects in workmanship for a period of one () year on the housing and metal parts, and carry Philips Lighting Company QL Induction Lighting System five (5) year warranty, from the date of sale of such goods to the buyer as specified in Kim Lighting shipment documents for each product. For an extended warranty coverage, contact factory. CAUTION: Fixtures must be grounded in accordance with national, state and/or local electrical codes. Failure to do so may result in serious personal injury. Listings and Ratings UL cul 598 CE IP66 Rated 25C Ambient Suitable for wet locations KIM LIGHTING RESERVES THE RIGHT TO CHANGE SPECIFICATIONS WITHOUT NOTICE.
Page: 2 of 5 Standard Features Mounting Plan View: Wall Mount : FM PT SA 2SB 3SY 4SC W NOTE: FM Flush Mount for direct mounting to top of pole. 3C", 4", 5", and 6" available. PT Pipe Tenon Mount for poles by others where a tenon is supplied. 2" pipe (2C" x 4" length). SA, 2SB, 3SY and 4SC Side Mount orientation using the arms in the Kim Arms and Poles Selection Guide. W Single Wall Mount configuration using the arms and wall plates in the Kim Arms and Poles Selection Guide. W Wall Mount arm is not included and must be ordered separately. See page 5 for styles and ordering information. Fixture designates fixture and light distribution. Coated lamps recommended. Horizontal Lamp Flat Glass Lens Bottom Mount: LEB9SS LEB9SC Light Distribution: : Single Straight Single Curved Double Curved Type V LEB9SSH5 LEB9SCH5 LEB9DCH5 LEB9DC Post Top Arm Mount
Page: 3 of 5 Standard Features Electrical Module IF = Induction Fluorescent Lamp Lamp Line Watts Type Volts 85 IF 277 Cat. Nos. for Electrical Modules available: 85IF20 85IF208 85IF240 85IF277 Lamp Induction Lamp ANSI Ballast Electronic Total System Watts 89 Finish Super TGIC powder coat paint over a titanated zirconium conversion coating. Photometrics Cat #: LEB9H5/85IF Report #: KL094 85 Watt 6 Mounting Height Color: Black Dark Bronze Light Gray Stealth Gray Platinum Silver White Custom Color 3 : BL DB LG SG PS WH CC 3 Custom colors subject to additional charges, minimum quantities and extended lead times. Consult representative. Custom color description: Transverse Distance in Units of Mounting Height 2 2 2 0 2.5..2.05 3.02.0 4 0 2 3 4 Longitudinal Distance in Units of Mounting Height -- Dashed Line: Half max candela trace
Page: 4 of 5 Optional Features Leaflet LEAF Heavy cast aluminum leaflets on top and bottom of luminaire arms. (SS) only. Medallion MDL Heavy cast aluminum medallions on top of luminaire arms. (DC) arms only. Finial TF Heavy cast aluminum finial on top of lantern housing. For use with Bottom Mount (BM) luminaire only. Photocell (see right) Factory installed photocell inside housing with a fully gasketed sensor on the side wall. Line Volts: Line Volts: A-30 20V A-33 277V A-3 208V A-32 240V Photocell Sensor Fusing (See right) High temperature fuse holders factory installed inside the fixture housing. Line Volts: 20V 208V 240V 277V : SF DF DF SF Single Fuse Poles See Kim Lighting s Arms and Poles Selection Guide.
Page: 5 of 5 Arm Options Arms Note: Refer to Kim Lighting s Arms and Poles Selection Guide for complete details. W Wall Mount arm is not included and must be ordered separately. Side Pole Swept Cast Arm Side Pole S-Shaped Up Cast Arm Side Pole S-Shaped Down Cast Arm Mounting Orientation SA 2SB 3SY 4SC HAS HAS-TM HAS-W HAS-TM2 HAS-TM3 HAS-TM4 HA2S HA2S-TM HA2S-W HA2S-TM2 HA2S-TM3 HA2S-TM4 HA3S HA3S-TM HA3S-W HA3S-TM2 HA3S-TM3 HA3S-TM4 Side Pole/Wall Mount Ribbon Arm w/bottom Scroll Side Pole/Wall Mount Ribbon Arm w/bottom Gusset Side Pole Ribbon Arm w/bottom Brace HA32S HA32S-TM HA32S-W HA32S-TM2 HA32S-TM3 HA32S-TM4 HA34S HA34S-TM HA34S-W HA34S-TM2 HA34S-TM3 HA34S-TM4 HA36S HA36S-TM HA36S-W Consult Consult Factory Factory Arm Finial: HAF2 - Traditional style finial available to close off mounting hub opposite the fixture.