Bulletin FA Stoddard Silencers Stoddard Silencers of Canada Inc. 91 Brimley Rd. Unit 1, Scarborough, Ontario, Canada M1J 1A Telephone () 291-390 FAX () 291-91 E-Mail - info@stoddardsilencers.com Web page - www.stoddardsilencers.com INTAKE FILTERS and FILTER SILENCERS
F6 Air Intake Filters and Filter Silencers Air Intake Filter and Filter Silencer The Series F6 Air Intake Filter and Filter Silencer is designed to mount directly on the inlet of an engine, blower or compressor. It will provide db to db noise reduction and the paper filter media has an efficiency of 99% on 1 micron particles. SERVICE LIFE & CLEANING: The service life of the element is dependent upon the surrounding environment and cannot be predicted. To prevent COLLAPSING of the filter element, STODDARD SILENCERS recommends the differential pressure across the filter element NOT exceed 1 inches of water column. Positive indication that the element requires cleaning or replacement can be provided with STODDARD SILENCERS model A0- Pressure Drop Indicator, at an extra charge. To extend service life, rap element gently to dislodge accumulated dirt. An alternate method is to direct compressed air ( PSIG max) through the element opposite to the direction of air flow. THE FILTER ELEMENT MUST EVEN- TUALLY BE REPLACED. ALTERNATE FILTRATION MEDIA AVAILABLE FOR F6 REFER TO PAGE FOUR Pre-Filter wrap available at added cost Consult Factory (90% on micron particles and larger) 30 Typical Attenuation Curve TYPICAL ATTENUATION - db F6 shown with optional A0- Pressure Drop Indicator. 0 63 12 20 00 1K 2K K K K OCTAVE BAND CENTER FREQUENCY (Hz) F6 Series Model A Connection Size B C D Rated CFM Wt. Replacement Element Number F6-1 11" 1 2 NPT 3 9 F- B F6-1 1 2 11 1 2" NPT 0 9 F- F6-2 12" 1 2 NPT 13 F- F6-2 1 2 12 1 2" NPT 10 F- C F6-3 13" 1 2 NPT 2 F-9 D F6-1" 1 2 NPT F-9 F6- " NPT/FLG 0 23 F-9 F6-6 " 1 2 Flange 123 0 F-1 F6-1" 1 2 Flange 13 212 0 F-111 A Connection Size F6- F6-12 F6-1 " 1 2 Flange 12" 1 2 Flange 1" 1 2 Flange 1 1 2 1 1 2 1 1 2 333 6 6 9 0 11 F-13 F-13 F-13 Sizes ", 12" and 1" are FILTERS only 2
Air Intake Filters and Filter Silencers F2 Air Intake Filter and Filter Silencer The Series F2 Air Intake Filter and Filter Silencer is designed to mount directly on the inlet of an engine, blower or compressor. It will provide db to db noise reduction. The Polyurethane filter media has an efficiency of 9% on micron particles and a stainless steel center core. SERVICE LIFE & CLEANING: The service life of the element is dependent upon the surrounding environment and cannot be predicted. To prevent COLLAPSING of the filter element, STODDARD SILENCERS recommends the differential pressure across the filter element NOT exceed 1 inches of water column. Positive indication that the element requires cleaning or replacement can be provided with STODDARD SILENCERS model A0- Pressure Drop Indicator, at an extra charge. Wash in sink or large pan using either water and any good washday type detergent and rinse clean. Squeeze out filter by pressing it against metal grid. Let stand and allow to dry completely. Pre-Filter wrap available at added cost Consult Factory (90% on micron particles and larger) 30 Typical Attenuation Curve TYPICAL ATTENUATION - db 0 63 12 20 00 1K 2K K K K OCTAVE BAND CENTER FREQUENCY (Hz) F2 shown with optional A0- Pressure Drop Indicator. F2 Series Model A Connection Size B C D Rated CFM Wt. Replacement Element Number F2-1 F2-1 1 2 11" 1 2 NPT 11 1 2" NPT 3 0 9 9 F-119 F-119 B F2-2 12" 1 2 NPT 13 F-119 F2-2 1 2 12 1 2" NPT 10 F-119 F2-3 13" 1 2 NPT 2 F-1 C F2-1" 1 2 NPT F-1 D F2-1" 1 2 NPT/FLG 0 23 F-1 F2-6 6" 1 2 Flange 123 0 F-121 F2-1" 1 2 Flange 13 212 0 F-122 F2- F2-12 F2-1 " 1 2 Flange 12" 1 2 Flange 1" 1 2 Flange 1 1 2 1 1 2 1 1 2 333 6 6 9 0 11 F-123 F-123 F-123 A Connection Size Sizes ", 12" and 1" are FILTERS only 3
Standard Filter Elements F6 Intake Filter Silencer F2 Intake Filter Silencer Paper Elements (Replaceable) Efficiency: 99% on 1 micron particles and larger Element # Housing Size F- 1" to 2 1 2" F-9 3" to " F-1 6" F-111 " F-13 " to 1" Polyurethane Elements (Washable) Efficiency: 9% on micron particles and larger Element # Housing Size F-119 1" to 2 1 2" F-1 3" to " F-121 6" F-122 " F-123 " to 1" Alternate Elements for F6 Polyester Felt Elements (Washable) Efficiency: 99% on 3 micron particles and larger Element # Housing Size F-11 1" to 2 1 2" F-13 3" to " F-13 6" F-139 " F-1 " to 1" Epoxy Coated Wire Mesh Elements (Washable) Efficiency: 90% on micron particles and larger Element # Housing Size F-129 1" to 2 1 2" F-130 3" to " F-131 6" F-132 " F-12 " to 1" Stoddard Silencers Stoddard Silencers of Canada Inc. 91 Brimley Rd. Unit 1, Scarborough, Ontario, Canada M1J 1A Telephone () 291-390 FAX () 291-91 E-Mail - info@stoddardsilencers.com Web page - www.stoddardsilencers.com LC-200-2/0
Bulletin F-6 Stoddard Silencers Stoddard Silencers of Canada Inc. 91 Brimley Rd. Unit 1, Scarborough, Ontario Canada M1J 1A Telephone () 291-390 FAX () 291-91 E-Mail - info@stoddardsilencers.com Web page - www.stoddardsilencers.com INLINE AIR FILTERS
F6 INLINE AIR FILTERS INLINE AIR FILTERS - PRESSURE SERVICE The Series F6 Inline Air Filter is designed to mount directly in the air piping system for engines, blowers or compressors. The filter element, which is fabricated from pleated paper media, has an efficiency of 99% on 1 micron particles and larger. The housing is designed to withstand an internal pressure of 1 psig. Pressure taps are provided on the intake and discharge nozzles for installation of a pressure drop indicator or switch by the customer. The F6 Inline Air Filter surfaces are prime coated with a primer. ALTERNATE FILTRATION MEDIA AVAILABLE FOR F6 Cleanable Polyurethane Foam - 9% on micron particles Cleanable Polyester Felt - 9% on 3 micron particles Epoxy Coated Wire Mesh - 90% on micron particles (When Oil Wetted) FOR VACUUM SERVICE USE F6V (See Page 3) F6 SERIES REPLACEMENT MODEL A B C E H RATED WEIGHT ELEMENT CFM (1) NUMBER F6-2 2 NPT 12 3 / 9 13 3 F- F6-2 1 / 2 2 1 / 2 NPT 12 3 / 9 10 0 F- F6-3 3 NPT 1 1 / 11 2 0 F-9 F6- * FLG 1 1 / 11 F-9 F6- * FLG 1 1 / 11 0 0 F-9 F6-6 *6 FLG 1 1 / 12 0 F-1 F6- * FLG 2 19 1 / 2 1 100 10 F-111 F6- * FLG 36 3 22 1 333 390 F-13 F6-12 *12 FLG 36 3 22 1 6 1 F-13 F6-1 *1 FLG 36 3 22 1 6 3 F-13 *Flanges match 12# ASA. Diameter and Drilling. (1) Rated capacity is based upon a maximum exit velocity of 00 fpm. 2
INLINE AIR FILTERS F6V INLINE AIR FILTERS - VACUUM SERVICE ONLY The Series F6V Inline Air Filter is designed to mount directly in the air piping system for engines, blowers or compressors. The filter element, which is fabricated from pleated paper media, has an efficiency of 99% on 1 micron particles and larger. The housing is designed to withstand a full vacuum. Pressure taps are provided on the intake and discharge nozzles for installation of a pressure drop indicator or switch by the customer. The F6V Inline Air Filter surfaces are prime coated with a red oxide primer. ALTERNATE FILTRATION MEDIA AVAILABLE FOR F6V Cleanable Polyurethane Foam - 9% on micron particles Cleanable Polyester Felt - 9% on 3 micron particles Epoxy Coated Wire Mesh - 90% on micron particles (When Oil Wetted) FOR PRESSURE SERVICE USE F6 (See Page 2) Wing Stud Flat Head Retainer Gasket Receptacle Rolled Angle F6 Shell F6V up to and including size: Coarse threaded wing studs allow for easy access to the F6V for servicing the filter elements. See diagram at left. F6V SERIES REPLACEMENT MODEL A B C E H RATED WEIGHT ELEMENT CFM (1) NUMBER F6V-2 2 NPT 12 3 / 9 13 3 F- F6V-2 1 / 2 2 1 / 2 NPT 12 3 / 9 10 0 F- F6V-3 3 NPT 1 1 / 11 2 0 F-9 F6V- * FLG 1 1 / 11 F-9 F6V- * FLG 1 1 / 11 0 0 F-9 F6V-6 *6 FLG 1 1 / 12 0 F-1 F6V- * FLG 2 19 1 / 2 1 100 10 F-111 *Flanges match 12# ASA. Diameter and Drilling. (1) Rated capacity is based upon a maximum exit velocity of 00 fpm. 3
F INLINE AIR FILTERS INLINE AIR FILTERS - VACUUM SERVICE ONLY The series F Inline Filter is a cost-effective alternative to the F6 Series Inline Filter. The F is designed to be mounted in the inlet piping or vacuum system piping for vacuum blowers, engines or compressors. The housing is rated to inches Hg vacuum. The filtering element is polyurethane foam with a stainless steel center core. The filter removes 9% of all particles micron size or larger. The F Inline Air Filter surfaces are painted with a gray machinery enamel finish. Flow Replacement Element F SERIES REPLACEMENT MODEL A B C D H WEIGHT ELEMENT NUMBER F-2 2 NPT 11 1 / / 1 / 1 F-0 F-2 1 / 2 2 1 / 2 NPT 11 1 / / 1 / F-0 F-3 3 NPT 11 1 / / 1 / F-0 F- NPT 12 11 1 / 3 / 1 / F-0 Stoddard Silencers Stoddard Silencers of Canada Inc. 91 Brimley Rd Unit 1, Scarborough, Ontario, Canada M1J 1A Telephone () 291-390 FAX () 291-91 E-Mail - info @ stoddardsilencers.com Web page - www.stoddardsilencers.com LC-200-2/0.