The TITN Experience - Expect More! WE SPECILIZE 735 Industrial Loop Road, New London, Wi 54961-2600 Phone: (920) 982-6600 Fax: (920) 982-7750 Outside Wisconsin: 1-800-558-3616 Website: www.titanconveyors.com Email: sales@titanconveyors.com Click on any area below to go to the catalog page Systems & Special Projects Slider Bed Belt Conveyors Roller Bed Belt Conveyors Floor to Floor Belt Conveyors Parts Conveyors Bulk Handling Conveyors Gravity Roller Conveyors Line Shaft Conveyors Chain Driven Live Roller Conveyors Belt Driven Live Roller Conveyors Zone ccumulation Transfer & Cooling Systems Hinged Steel Belt Conveyors Replacement Hinged Steel Belting Slat Conveyor Drag Chain Conveyor Turn Table pplication Wire Mesh/Plastic Belt Conveyors Ball Transfer Table Solid Waste Handling Conveyor Carton Length 1/3 1/3 1/3 Diagram 2 Center of Gravity Carton Length 1/3 1/3 1/3 Diagram 1 Center of Gravity Carton Height Carton Height Conveyor Incline ngle Multi-Strand Chain Conveyor Pallet Pro Conveyor Supports Controls & ccessories Engineering Data
SYSTEMS & SPECIL PROJECTS Titan s engineering capability offers our customers the ability to have special material handling capability conveyors designed especially for their needs. We excel in our ability to meet every need our customers desire. Whether it be a complete factory system or a special conveyor Titan is your answer to increased productivity. utomotive tire handling system Titan designed heavy duty Chain Driven Live Roller paper industry warehouse system. Titan designed system for moving rolls of builders felt toward packaging and distribution. Titan designed factory robotic system for delivery of plasic rolls to assembly. Tire Recycling System Special transfer turntable Titan designed CDLR system Titan Special CDLR Scissors lift with safety skirting
SLIDER BED MODEL 102 MINI-PRO PRESS CONVEYOR Low profile scrap and parts removal from die press Knurled drive for positive pull Series application to common drive 2" Req'd Length 11 1/2" MODEL 102 SLIDER BED CONVEYORS SPECIFICTIONS STNDRD OPTIONS + 1/2 9 1/4" Belt Widths 4, 6, 8, 12, 18, 24 2, 10, 14, 16, 20 1 15/32" Lengths 2 to 10 3 to 10 Belt Type PVC 50 Black Food Grade or belt to suit application Drive 1/4 HP 115/1/60 Gearmotor 1/2 HP 230/460/3/60 TEFC, severe duty, inverter duty, brake motor Drive Pulley 2 dia. crowned, knurled 1-1/2 deep formed 12 ga. H.P., drive location, speed, fixed or variable speed, belt type, siderails, supports, casters, side take-up, special paint, belt scraper, food grade, Many other options available, consult factory representative MODEL 104 SLIDER BED BELT CONVEYOR Square head and tail for system assembly Easily integrated to other types of conveyors Screw take-up Req'd Length MODEL 104 SLIDER BED CONVEYOR SPECIFICTIONS 4" + 4" Belt Widths 12, 18, 24, 30, 36 4, 6, 8, 10, 14, 16, 20, 40 Lengths 5 min. to 40 max 3 min to 50 max Belt Type PVC 120 Black Rough top, food grade, V-guide on bottom, belt to fit application Drive 1/2 HP 230/460/3/60 3/4, 1, 1-1/2, 2 HP, 115/2301/60, 575/3/60, TEFC, washdown, severe duty, invertrer duty, brake motor Drive Pulley 4 dia. crowned, rubber lagged Machined & balanced pulleys for high speed 4 deep formed 12 ga. H.P., drive location, speed; fixed or variable speed, controls, belt type, center drive & take-up, galvanized, stainless, siderails, transfer roller, V-guide,, supports, casters, other belt types, siderail skirting, special paint Req'd Length MODEL 108 SLIDER BED BELT CONVEYOR Rugged industrial design Square head and tail for system assembly Grease sealed bearings and screw take-up + 4" 4 IC-60 9 9 1/32" MODEL 108 SLIDER BED CONVEYORS SPECIFICTIONS Belt Widths 12, 18, 24, 30, 36, 48 6, 8, 10, 14, 16, 20, 40, 42, 54, 60 Lengths 5 min. to 150 max. 3 min. to 180 max. Belt Type PVC 120 Black Rough top, food grade, V-guide on bottom, Drive 1/2 HP 230/460/3/60 3/4, 1, 1-1/2, 2 HP 115/230/1/60 TEFC, washdown, severe duty, inverter duty, brake motor Drive Pulley 8 dia. crowned, rubber lagged 4 deep formed 12 ga. H.P., drive location, center drive & take-up, speed; fixed or variable speed, controls, belt type to fit application, galvanized, stainless, siderails, siderail skirting, supports, Transfer roller, bolt-on end stop, belt scraper, e-stop with pull cord, v-guided belt for positive tracking, machined and balanced pulleys for high speed,casters, special paint
ROLLER BED Req'd Length MODEL 105 ROLLER BED CONVEYOR Heavy loads with rollers to decrease friction Modular design for system assembly 5 6 1/2" 13 3/4" Belt Width +4" Belt Width +1" MODEL 105 ROLLER BED BELT CONVEYORS Belt Widths 12, 18, 24, 30, 36 4, 6, 8, 10, 14, 20 Lengths 5 min. to 100 max. 3 min. to 150 max. Belt Type PVC 120 Black Rough top, Food grade, to suit application Drive 1/2 HP 230/460/3/60 3/4, 1, 1-1/2, 2, 3 HP, TEFC, washdown, severe duty, inverter duty, brake motor Drive Pulley 4 dia. crowned rubber lagged 8 dia. becomes Model 109 5 deep formed 12 ga. Roller Size 1.9 dia. x 16 ga. 2.5 dia. x 11 ga. Rollers Center 6 centers Other centers available Belt widths from 4 to 48, lengths, roller spacing, roller size, other belt types; stainless construction, controls, e-stop with pull cord, transfer roller, rough top, food grade, H.P., center drive & take-up, drive location, speeds, variable speed drives, controls, siderails, supports, casters, special paint MODEL 109 ROLLER BED CONVEYOR Extra heavy loads Modular design for system assembly 18 " Req'd Length 9" +4" +1" 16 3/4" 6" MODEL 109 ROLLER BED CONVEYORS Belt Widths 12, 18, 24, 30, 36 8, 10, 14, 16, 20, 40, 42, 54, 60 Lengths 5 min. to 100 max. 3 min. to 180 max. Belt Type PVC 120 Black Rough top, food grade, V-guide on bottom Drive 1/2 HP 230/460/3/60 3/4, 1, 1-1/2, 2 HP 115/230/1/60 TEFC, wahsdown, severe duty, inverter duty, brake motor Drive Pulley Roller Size 8 dia. crowned rubber lagged 6 deep formed 12 ga. 2.5 dia. x 11 ga. Rollers Center 6 centers Other centers available H.P., drive location, center drive & take-up, speed; fixed or variable speed, controls, belt type to fit application, galvanized, stainless, siderails, siderail skirting, supports, Transfer roller, bolt-on end stop, belt scraper, e-stop with pull cord, v-guided belt for positive tracking, machined and balanced pulleys for high speed,casters, special paint Many other options available, consult factory representative
FLOOR TO FLOOR MODEL 204 FLOOR-TO FLOOR SLIDER BED CONVEYOR Utilize floor space Smooth transition made possible with ben roller at transition and discharge nose over djustable supports MODEL 204 FLOOR TO FLOOR SLIDER BED CONVEYOR Belt Widths 12, 18, 24, 30, 36 4, 6, 8, 10, 14, 16, 20 Lengths 5 min. to 40 max. 3 min to 50 max Belt Type Rubber rough top Gum rubber Drive 1/2 HP 230/460/3/60 3/4, 1, 1-1/2, 2, 3, HP, 115/230/1/60, TEFC, wahsdown, severe duty, inverter duty, brake motor Drive Pulley 4 dia. crowned, rubber lagged 4 deep formed 12 ga. +4" H.P., drive location, speed, fixed or variable speed, controls, power feeder, belt type, center drive & take-up, transfer rollers, bolt-on end stop, belt scrapper, galvanized, stainless, siderails, supports, casters, other belt types, siderail skirting, special paint 4" 12" Discharge Length Many other options available, consult factory representative Req'd Incline Length 7 3/16" 32 1/8" 15 To 30 7 3/4" (IC-45) 9" (IC-60) STNDRD CENTER DRIVE & TKE-UP MODEL 208 FLOOR-TO-FLOOR SLIDER BED CONVEYOR Extra duty industrial system Longer elevations Modular design for system assembly MODEL 208 FLOOR TO FLOOR SLIDER BED CONVEYOR Belt Widths 12, 18, 24, 30, 36, 48 6, 8, 10, 14, 16, 20, 40, 42, 54, 60 Lengths 5 min. to 50 max. 3 min to 50 max Belt Type Rubber rough top Gum rubber Drive 1/2 HP 230/460/3/60 3/4, 1, 1-1/2, 2, 3, HP, 115/230/1/60, TEFC, wahsdown, severe duty, inverter duty, brake motor Drive Pulley 8 dia. crowned, rubber lagged drive 4 deep formed 12 ga. + 4" 12" Discharge Length 4" H.P., drive location, speed, fixed or variable speed, controls, power feeder, belt type, center drive & take-up, transfer rollers, bolt-on end stop, belt scrapper, galvanized, stainless, siderails, supports, casters, other belt types, siderail skirting, special paint Many other options available, consult factory representative Req'd Power Feeder Length Req'd Incline Length 16 5/8" 7" 15 To 30
PRTS CONVEYORS Page 1 of 2 MODEL 304 CLETED RUBBER BELT CONVEYOR Rugged construction and versatile djustable under carriage Ideal for moving small parts from one process to another *Unit shown with optional hopper MODEL304 SPECIFICTIONS Belt Widths 4, 6, 8, 12, 18, 24, 36 10, 14, 16, 30, 30 Lengths 5 to 12 3 min. to 20 Belt Type 2 Ply black neoprene with 1-1/2 cleats on 12 centers Cleated PVC, food grade, plastic belt, cleat centers & heights to suit Drive 1/2 H.P. 230/460/3/60 3/4, 1, 1-1/2, HP, 115/230/1/60, TEFC, washdown, severe duty, inverter duty, brake motor Drive Pulley 4 dia. crowned rubber lagged 6-1/2 deep formed 12 g.a. 24" Speed, variable speed, belt widths, belt type, side mount/bottom mount drive, controls, hopper, discharge chute, siderails, galvanized, stainless, supports, adjustable undercarriage, casters, special paint 17" 10" + 2 1/16" + 9/16" 16 Decline Required Length 45 24-29 Maximum Discharge Minimum Infeed Minimum Drive Minimum Infeed Horizontal Minimum Discharge Maximum Infeed Max. Dr. W/Min. In. 4 Ft. 35 3/4" 5 1/4" 6 Ft. 52 1/2" 5 1/4" 8 Ft. 69 1/2" 5 1/4" 10 Ft. 86 1/2" 5 1/4" 12 Ft. 103 1/2" 5 1/4" Max. Dr. W/Min. In. Max. Dr. W/Min. In. 28" (29 ) 7 1/4" 34 3/4" 35" 39 1/4" (29 ) 6 3/4" 46 3/4" 46 3/4" 49 1/4" (28 ) 6 1/2" 60 1/4" 60 1/4" 56 1/2" (24 ) 9" 77 1/4" 77 1/4" 66 1/4" (24 ) 9" 77 1/4" 77 1/4" Max. Dr. W/Min. In. 25 1/4" 36 3/4" 31 1/2" 49 1/2" 38" 63 3/4" - - - - MODEL 305 FLT WIRE MESH CONVEYOR Heavy duty construction Ideal for heat treated, washed, dried or quenched parts djustable supports Numerous belts available MODEL 305 SPECIFICTIONS Belt Widths 4, 6, 8, 12, 18, 24, 36 10, 14, 16, 20, 30 Lengths 5 min. to 12 max. 3 min. to 20 Belt Type 1/2 x 1 gal. flat wire mesh w/ 1-1/2 high cleats on 12 centers Other wire mesh types, plastic belts, cleat height & spacing 24" 17" +2 1/16" +9/16" Drive 1/2 H.P. 230/460/3/60 Drive Sprocket 13 tooth, 4.4 P.D., H.D., Keyed 3/4, 1, 1-1/2, HP, 115/230/1/60, TEFC, washdown, severe duty, inverter duty, brake motor 10" 6-1/2 deep formed 12 g.a. Required Length Fixed speed, variable drives, controls, e-stop with pull cord, side mount/bottom mount drive, belt widths, belt type, siderails, hopper, discharge chute, galvanized, stainless, knee braces, ceiling brackets, supports, casters, special paint, cleat height - consult factory
PRTS CONVEYOR Page 2 of 2 MODEL 310 Parts Conveyor Designed for lightweight parts Horizontal/incline with no transfer djustable undercarriage with 10 dia. wheels MODEL 310 SPECIFICTIONS Belt Widths 12, 18, 24 Specify belt width Lengths 24 infeed, 36 incline 36, 48, 60 infeed, 48, 60, 72 incline Curves 30 o, 45 o 60 o Belt Type Black PVC 120 with 1 1/2 high cleat on 12 centers (max.) Food grade belts - cleats Drive 1/2 H.P. 230/460/3/60 Drive Pulley 4 diameter crown faced rubber lagged 6 1/2 deep formed 12 ga. 3/4, 1, 1-1/2, HP, 115/230/1/60, TEFC, washdown, severe duty, inverter duty, brake motor 2 1/8" "D" + 2 13/16" - 1" Drive location, speed, variable speed, controls, lengths, belt type, infeed hopper, discharge chute, siderails, supports, casters, special paint, cleats - Consult Factory 8 5/8" +1" "B" "C" 30 "D" O..L. "B" (Incline) 36" 48" 60" 72" 24" 71 81.5 92 102.5 36" 83 93.5 104 114.5 48" 95 105.5 116 126.5 60" 107 117.5 128 138.5 "C" Hgt. 26 32 38 44 "" I N F E E D "" I N F E E D 45 "D" O..L. "B" (Incline) 36" 48" 60" 72" 24" 65.5 74 82.5 91 36" 77.5 86 94.5 103 48" 89.5 98 106.5 115 60" 101.5 110 118.5 127 "C" Hgt. 34.7 43.2 51.7 60.2 "" 30 or 45 STD. 4"-24" DJ. MODEL 350 PRO FEED STEEL BELT PRTS CONVEYOR Wide variety of parts Exclusive powdered metal sidewings eliminate trapping of parts + 4 1/4" MODEL 350 PRO FEED SPECIFICTIONS 6 15/16" Belt Width 12 Specify Belt With Discharge 6 0 off floor Specify discharge height Belt Type 2-/2 pitch hinged steel Drive 1/2 H.P. 230/460/3/60 Drive to suit application 30" (7 CUBIC FOOT) HOPPER STNDRD 12 1/4" 98"OVERLL HEIGHT Hopper 7 cu. ft. Custom hoppers available Formed 10 ga. Discharge heights, discharge chute, belt widths, belt type, speed, variable speed, controls, drive, galvanized, stainless, casters, paint, Hopper size - Consult factory 36" STNDRD 72" STNDRD
BULK HNDLING Page 1 of 2 MODEL 340 BULK HNDLING CONVEYOR Move delicate product horizontally, upward and horizontally without product degradation due to transfer Designed to quickly get product from beneath one operation, up a high degree incline and over into the center of another process Many belt widths and sidewall depths are available depending on volume of product and space availability Reduce screw conveyor/bucket elevator combination type systems with no product damage The belt is readily available and comes in black or food grade white 24" Min. Belt Width Length MODEL 340 SIDEWLL CONVEYOR Selected to suit application Determined by application ctual Belt Width + 11 1/4" ctual Effective B. W. Belt Type Selected to suit application Food grade belting Drive 1/2 HP 230/460/3/60 3/4, 1, 1-1/2, 2 HP, 115/230/1/60, TEFC, washdown, sever duty, inverter duty, brake motor 11" Curves 30 0, 45 0, 60 0 curves available Other angles available Formed 12 gauge Stainless steel construction, siderails, bolt-on bottom pans, belt thumper at discharge, top covers, casters, e-stop with pull cord consult factory 27" Min. Std. 15, 30, 45 60 & 75 MODEL 460 BULK HNDLING CONVEYOR Specifically designed to handle large volumes of heavy, abrasive and granular products at a very reasonable cost Rugged construction and certified components provide for long run, outdoor application 2 - roll to 12 width belt - 3 - roll to 48 width belt MODEL 460-3 ROLL TROUGH BULK HNDLING Belt Widths Lengths Belt Sized by application Per application Per application Drive 1 H.P. 230/460 Drive Pulley 14 dia. crown face rubber lagged drive and 14 tail 6 structural channel Idler Rollers 2 or 3 roll CEM OPTIONS 2-roll available, Drive as needed, Belt Width - consult factory, Idlers 35 & 45 degree available, consult factory on take-ups and maximum lengths, Drive location, Speed, Variable speed available, H.P., Controls, Infeed hoppers, skirting, belt scraper, Paint, Supports, 20 =10 1/16" 35 =12 1/8" 7" 35" 24" 20 =25 3/4" 35 =23" 8 15/16" 3-Roll Typical Cross Section Consult Factory for belt widths 6" 9 1/4"
IC-45 BULK HNDLING Page 2 of 2 MODEL 114 BULK HNDLING CONVEYOR Cost competitive for light duty bulk conveyor 1 piece formed sides and deck Formed trough 4 drive pulley and 4 tail Overall Length s Required MODEL 114 SLIDER BED TROUGH CONVEYORS Drive on Near Side Belt Widths 12, 18, 24, 30, 36 8, 14, 16, 20, 40 Belt Width +4" Belt Width +1" Lengths 5 min. to 40 max. 3 min. to 40 max. Belt Type PVC 120 Black Food grade 1 9/16" Ref. 3 1/2" 20 Drive 1/2 H.P. 230/460/3/60 3/4, 1, 1-1/2, 2 HP, 115/230/1/60, TEFC, washdown, severe duty, inverter duty, brake motor 4" Drive Pulley 4 dia. crowned rubber lagged - 4 tail pulley 4 deep formed 12 g.a. H.P., drive location, speed, fixed or variable speed, controls, belt widths, belt type, center drive & take-up, galvanized, stainless, siderails, supports, casters, other belt types, siderail skirting, belt scrapper, machined and balanced pulleys for high speed, discharge housing, e-stop with pull cord, special paint Many other options available, consult factory representative MODEL 118 BULK HNDLING CONVEYOR Cost competitive medium duty bulk conveyor 1 piece formed sides and deck Formed trough 8 drive pulley and 4 tail Belt Travel 8 1/4 T.U. Overall Length 32" MODEL 118 SLIDER BED TROUGH CONVEYORS Belt Widths 12, 18, 24, 30, 36 8, 14, 16, 20, 40 Lengths 5 min. to 40 max. 3 min. to 50 max. Belt Type PVC 120 Black Food grade Drive 1/2 H.P. 230/460/3/60 3/4, 1, 1-1/2, 2 HP, 115/230/1/60, TEFC, washdown, severe duty, inverter duty, brake motor Drive Pulley 8 dia. crowned rubber lagged - 4 tail pulley 4 deep formed 12 g.a. H.P., drive location, speed, fixed or variable speed, controls, belt widths, belt type, center drive & take-up, galvanized, stainless, siderails, supports, casters, other belt types, siderail skirting, belt scrapper, machined and balanced pulleys for high speed, discharge housing, e-stop with pull cord, special paint Many other options available, consult factory representative 16" Center Drive & Take-Up Shown Belt Width +4" Belt Width +1" 3 1/2" 1 9/16" Ref. 20 4" Max. Dim. Reducer 7 3/4" IC-45 7 3/4" IC-60 11 1/4" IC-70 12 3/4" IC-80 14 5/8" IC-100
GRVITY ROLLER GRVITY ROLLER CONVEYOR vailable in popular standard diameters Modular design for systems assembly Varied tube pack arrangements Matched roller specifications to frame construction True roller rating MODEL MODEL 413 413 MIN. ROLLER MIN. CENTERS ROLLER CENTERS 1 1/2" 1 1/2" 1/4" OVERLL FRME WIDTH BETWEEN FRMES B.F. 1" 2 1/2" ROLLERS SET HIGH ROLLERS SET LOW 1/2" MODEL MODEL 419 419 MODEL MODEL 420 420 MIN. ROLLER MIN. CENTERS ROLLER CENTERS 3" 3" 1/4" 3 1/2" OVERLL FRME OVERLL FRME WIDTH WIDTH B.F. 1 1/2" 3/4" STYLE #1 STYLE #2 STYLE #3 ROLLERS SET HIGH ROLLERS SET LOW MODEL MODEL 425 425 OVERLL FRME OVERLL FRME MIN. ROLLER MIN. CENTERS ROLLER CENTERS WIDTH WIDTH 3" 3" 1/4" B.F. 1 1/2" MODEL MODEL 426 426 3 1/2" ROLLERS SET HIGH ROLLERS SET LOW OVERLL FRME OVERLL FRME MIN. ROLLER MIN. CENTERS ROLLER CENTERS WIDTH WIDTH 3" 3/16" B.F. 1 1/2" 3" 3/16" B.F. 1 1/2" 5/8" COTTER PIN RETINING STRIP SPRING LODED NOTE: NOT VILBLE ON MODEL #435 3 1/2" 3 1/2" 5/8" 5/8" MODEL MODEL 435 435 MIN. ROLLER MIN. CENTERS ROLLER CENTERS 4" 4" ROLLERS SET ROLLERS ROLLERS SET SET ROLLERS SET HIGH HIGH LOW LOW OVERLL FRME OVERLL FRME WIDTH WIDTH 3/8" 3/8" B.F. B.F. 2" 2" 6" 6" 1 1/2" 1 1/2" ROLLERS SET ROLLERS ROLLERS SET SET ROLLERS SET HIGH HIGH LOW LOW GRVITY ROLLER CONVEYOR SPECIFICTIONS MODEL NUMBER ROLLER XLE FRME MINIMUM CENTERS ROLLER RTING* 413 1-3/8 Dia. x 18 Gauge 5/16 Hex Formed 12 Gauge 1-1/2 50 lbs. 419 420 1.9 Dia. x 16 Gauge 2 Dia. x 16 Gauge 7/16 Hex Formed 10 Gauge 3 250 lbs. 425 2-1/2 Dia. x 11 Gauge 11/16 Hex Formed 7 Gauge 3 625 lbs. 426 2-5/8 x 7 Gauge 11/16 Hex Formed 7 Gauge 3 650 lbs. 435 3-1/2 x.300 wall 1-1/16 Hex Roller Centers vailable Model 413: 1-1/2, 3, 4-1/2, 6, 9, 12 Model 419-425-426: 3, 4-1/2, 6, 9, 12 Model 435: 4, 6, 8, 12 6 @8.2# Structural Channel 4 2500 lbs. Siderails - 1,, 3-1/2, 6 fixed channel, 3-1/2 high adjustable, casters, galvanized, coated, plastic or stainless steel rollers, pop-up stops - manual or air operated, fixed end stops, manual gates, paint *Roller Ratings Vary with Between Dimensions
Line Shaft Conveyors PTHWY LINESHFT CONVEYOR Economically use for simple transportation Can be integrated into total computer directed systems Can be used for lifting, rollover, transfer, upend, speed up, slow down, brake and accumulate Easy reconfiguration LINE SHFT INDIVIDUL BELT DRIVEN ROLLER CONVEYOR Guide Rail djustable Guard Rail ssembly Drive Bushing Shaft Coupler Drive Cross Shaft Tie Fully Guarded Belt Powered Rollers Channel Floor Support Quiet The elastomeric belt holds the rollers and the drive bushings firmly under tension. This eliminates the conventional rattling, jiggling and jangling... fewer moving parts make less noise Dwell points or work stations Reverse the twist in the elastomeric belts for dwell points or work stations. 3 1 2 4 5 8 7 9 15 10 1 14 12 11 13 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 90 0 Belt Transfer Curve Guard Drive Unit Drive Shaft Line Shaft Guard L.S. Bushings Belts Rollers 90 0 Gravity Transfer Guide Wheel 45 0 Merge Skewing 30 0 Switch Skewing Roller axles are spring loaded and can be easily moved one hole on the sidewall for diverting or aligning. Powered skew and herring-bone sections are available. Clean The lineshaft drive system eliminates dirt and grime gathering so the rollers can be clean as the materials they convey. Sensible Each roller, drive bushing and belt operate like a slip clutch... the torque to each roller is adequate to drive the roller, but the slip clutch effect allows each roller to stop.
CHIN DRIVEN LIVE ROLLER 13 1/2" 16 3/4" 11 1/2" Page 1 of 2 Bottom Mount Drive 8" Side Mount Drive 3 3/4" OVERLL LENGTH MODEL 519 CHIN DRIVEN LIVE ROLLER Designed for lighter loads and positive drive 13" ROLLER HEIGHT 17 1/2" MODEL 519 CHIN DRIVEN LIVE ROLLER CONVEYOR SPECIFICTIONS Effective Widths 13 to 40 Specify up to 40 E.W. Lengths 5 min. 3 min., max. based on application Roller Size 1.9 Dia. x 16 ga. with 7/16 hex shaft 4 5/16" EFFECTIVE WIDTH 1 1/4" EFFECTIVE 1 1/2" 4 5/16" 1 1/2" WIDTH 1 1/4" 1 1/4" 1/4" 5" 3 3/4" 3 3/4" Roller Center 4 6, 8, 12 Formed 10 ga. 3 1/8" Rollers Set High 3 1/8" Rollers Set Low Drive 1/2 H.P. 230/460/3/60 3/4, 1, 1-1/2, 2 H.P. 230/460/3/60 Chain Drive #40 #50 available Roller Space - Consult factory, Roller Center - Consult Factory, Drive locations: as needed, Galvanized or stainless construction, H. P., Speeds, Variable speed, Controls, Coated rollers, Paint, 2 or 3 strand chain transfers, Pallet lifts, C Face brake and Fixed end stop, Rollers set low, UHMW sleeves and Knee braces, ir operated blade stop, Supports - 6 @ #8.2 structural channel MODEL 525 CHIN DRIVEN LIVE ROLLER Designed for handling pallets, skids, drums MODEL 525 CHIN DRIVEN LIVE ROLLER CONVEYOR SPECIFICTIONS Effective Widths 13 to 40 Specify up to 40 E.W. Lengths 5 min. 3 min., max. based on application Roller Size 2 Dia. x 11 ga. with 7/16 hex shaft - 580 lb. roller cap. Roller Center 5 2-13/16, 3-7/16, 4-3/8, 5-15/16, 10 Formed 10 ga. Drive 3/4 H.P. 230/460/3/60 1, 1-1/2, 2, 3 H.P. 230/460/3/60, severe duty, inverter duty, brake motor Chain Drive #50 #60 available OVERLL LENGTH Roller Space - Consult factory, Roller Center - Consult Factory, Drive locations: as needed, Galvanized or stainless construction, H. P., Speeds, Variable speed, Controls, Coated rollers, Paint, 2 or 3 strand chain transfers, Pallet lifts, Pallet jack plates for side or end load, C Face brake and Fixed end stop, Rollers set low, UHMW sleeves, ccumulation sleeves, Knee braces, ir operated blade stop, Supports - 6 @ #8.2 structural channel 13" SUPPORTS 18 3/8" (IC-60) 19 1/2" (IC-70) 20 7/8" (IC-80) REDUCERS MODEL 526 CHIN DRIVEN LIVE ROLLER CONVEYOR Designed for handling pallets, skids, drums MODEL 526 CHIN DRIVEN LIVE ROLLER CONVEYOR SPECIFICTIONS Effective Widths 15 to 72 Specify Lengths 5 min. 3 min. - max. per application 16 3/4" 13 1/2" Roller Size 2 5/8 dia. x 7 ga. with 11/16 hex shaft Roller Center 5 2-13/16, 3-19/32, 4-3/8, 5-15/16, 10 11 1/2" Bottom Mount Drive 8" Side Mount Drive 3 3/4" Formed 7 ga. Drive 3/4 H.P. 230/4603/60 1, 1-1/2, 2 H.P. 115/230/1/60, 575/3/60, severe duty, inverter duty, brake motor OVERLL LENGTH Chain Drive #50 #60 13" 17 1/2" ROLLER HEIGHT Roller Space - Consult factory, Roller Center - Consult Factory, Drive locations: as needed, Galvanized or stainless construction, H. P., Speeds, Variable speed, Controls, Paint, 2 or 3 strand chain transfers, Pallet lifts, C Face brake and Fixed end stop, Rollers set low, UHMW sleeves, Knee braces, ir operated blade stop, Supports - 6 @ #8.2 structural channel 4 5/16" EFFECTIVE WIDTH 1 1/4" EFFECTIVE 1 1/2" 4 5/16" 1 1/2" WIDTH 1 1/4" 1 1/4" 1/4" 5" 3 3/4" 3 3/4" 3 1/8" Rollers Set High 3 1/8" Rollers Set Low
CHIN DRIVEN LIVE ROLLER Page 2 of 2 MODEL 535 CHIN DRIVEN LIVE ROLLER CONVEYOR Designed for extremely heavy duty use Modular design to fit system application MODEL 535 CHIN DRIVEN LIVE ROLLER CONVEYOR STNDRD OPTIONS Effective Widths 15 to 66 Customer can specify Lengths Per application - 5 Minimum 3 minimum, maximum length based on application 16 3/4" 13 1/2" Roller Size 3 1/2 dia. x.300 wall 1-1/16 hex shaft (#2500 roll rating) Roller Centers 6 Roller centers of 4-7/8, 6, 9, 10-1/8, 12 with #60 sprockets #80 roll-to-roll chain drive with roller centers of 6-7/16, 9-7/16, 12-7/16 11 1/2" Bottom Mount Drive OVERLL LENGTH 3 3/4" 8" Side Mount Drive Structural channel Drive 3/4 H.P. 230/460/3/60 1, 1-1/2, 2, 3, 5 HP, 115/230/1/60, 575/3/60, severe duty,inverter duty, brake motor 13" Chain Drive #60 #80 17 1/2" ROLLER HEIGHT Roller Space - Consult factory, Roller Center - Consult Factory, Drive locations: as needed, Galvanized or stainless construction, H. P., Speeds, Variable speed, Controls, Paint, 2 or 3 strand chain transfers, Pallet lifts, C Face brake and Fixed end stop, Rollers set low, UHMW sleeves, Galvanized rollers, accumulation sleeves, Knee braces, ir operated blade stop, Supports - 6 @ #8.2 structural channel, Pop-up roller, blade stops, pallet lifts. 4 5/16" EFFECTIVE WIDTH 1 1/4" 1 1/2" 1/4" 4 5/16" EFFECTIVE WIDTH 1 1/4" 1 1/2" 1 1/4" 5" 3 3/4" 3 3/4" MODEL 595 90 0 TPERED CHIN DRIVEN LIVER ROLLER Heavy duty conveying of pallets, drums and skids Modular design to fit system application 3 1/8" Rollers Set High 3 1/8" Rollers Set Low MODEL 595 CHIN DRIVEN LIVE ROLLER 900 CURVE CONVEYOR SPECIFICTIONS Effective Widths 15 to 66 Specify Lengths Per application Per application Roller Size 3 1/2 dia. x.300 wall with 1-1/16 hex shaft on 6 centers (#3000 roll rating) Roller Center 6 Structural channel Drive 3/4 H.P. 230/460/3/60 4-7/8, 9, 10-1/8, 12 with #60 sprockets 6-7/8, 9-7/16, 12-7/16 with #80 chain 1, 1-1/2, 2, 3, 5 HP, 115/230/1/60, 575/3/60 severe duty, inverter duty, brake motor Chain Drive #60 #80 Roller Space - Consult factory, Roller Center - Consult Factory, Drive locations: as needed, Galvanized or stainless construction, H. P., Speeds, Variable speed, Controls, Paint, C Face brake and Fixed end stop, Rollers set low, UHMW sleeves, Knee braces, ir operated blade stop, Supports - 6 @ #8.2 structural channel, 90 B B 4 13/16" Effective Width 3/8" 5 13/16" 5 13/16" 1 11/16" 17 13/16" Section B - B Section - 1 1/8" 11 1/2"
BELT DRIVEN LIVE ROLLER MODEL 402 BELT DRIVEN LIVE ROLLER CONVEYOR Light Duty Close roller centers MODEL 402 BELT DRIVEN LIVE ROLLER CONVEYOR SPECIFICTIONS BF Dimensions 9, 13, 16, 22 25, 28 Lengths 3 Min. to 50 Max. Roller Size 1 3/8 dia. x 18 ga. with 5/16 hex axle 1.9 x 16 ga. with 7/16 hex axle Roller Centers 3 1-1/2, 3, 6 Belt Type PVC 120 Others available 6 1/2 deep formed 12 ga. 6 1/2 deep formed 12 ga. Drive 1/2 H.P. 230/460/3/60 3/4, 1, 1-1/2, 2 HP, TEFC, severe duty, inverter duty, brake motor Drive Pulley 4 dia. crown faced rubber lagged Belt Type, Drives - Fixed speeds-specify speed req., variable speed with DC motor and SCR controller or C inverter, Motor, Controls, Internal take-up, Center drive, 1, 3 1/2, & 6 side rails available, Casters - 4 or 6 rigid, Side mount drive, Knee braces/ceiling hangers, Bolt on bottom pans, Rollers on 1 1/2 centers, Galvanized or Stainless steel construction MODEL 404 BELT DRIVEN LIVE ROLLER CONVEYOR Medium to industrial duty C C D D End Drive Overall Length Product Flow Belt Travel B B BF Dimensions 13, 16, 22, 25, 28, 31, 34, 37, 40 Specify 1/4" Lengths 3 Min. to 100 Max. Roller Size Roller Centers MODEL 404 BELT DRIVEN LIVE ROLLER CONVEYOR SPECIFICTIONS 1.9 x 16 ga. with 7/16 hex axle 6, (3, 4-1/2 ) Belt Type PVC 120 6 1/2 deep formed 12 ga. 6 1/2" Drive 1/2 H.P. 230/460/3/60 3/4, 1, 1-1/2, 2 HP, TEFC, severe duty, inverter duty, brake motor Drive Pulley 4 dia. crown faced rubber lagged Tail Section Infeed Section Belt Type, Drives - Fixed speeds-specify speed req d., variable speed with DC motor and SCR controller or C inverter, Motor - 3/4, 1, 1-1/2, 2 HP, TEFC, severe duty, inverter duty, brake motor, Controls, Internal take-up, Center drive, 1, 3 1/2, & 6 side rails available, Casters - 4 or 6 rigid, Side mount drive, Knee braces/ceiling hangers, Bolt on bottom pans, Galvanized or Stainless steel construction Center Drive & Take-up Overall Length Product Flow Belt Travel MODEL 408 BELT DRIVEN LIVE ROLLER CONVEYOR For applications requiring medium to heavy duty MODEL 408 BELT DRIVEN LIVE ROLLER CONVEYOR SPECIFICTIONS Same as Model 404 Except - 8 dia. heavy duty drive belt pulley with 4 tail pulley Same as Model 404 MODEL 490 BELT DRIVEN LIVE ROLLER CONVEYOR Economical 900 curve System compatible with other Titan Units Between 13, 16, 22, 25, 28, 31, 34, 37, 40 20 1/8" Tapered rollers 13, 16, 22, 28, 34, 40 Curves MODEL 490 V-BELT DRIVEN LIVE ROLLER CURVE CONVEYOR 90 0 standard, (30 0, 45 0 Opt.) Rollers 1.9 dia. x 16 ga., 2-1/2 centers on inside radius Tapered rollers Drive 1/2 H.P. 230/460/3/60 Formed 12 ga. Center Drive & Take-up 3 13/16" 24" 2 9/16" 3/4, 1, 1-1/2, 2 HP, TEFC, severe duty, inverter duty, brake motor Section - Roller sizes, siderails, caster, transfer rollers, galvanized, coated, tapered rollers, stainless or galvanized construction, motors, speeds, variable speed, drive location, casters, controls, paint, supports 7 5/8" (IC-45) 9 1/4" (IC-60) 6" 2 1/2" Centers Typ. Belt Travel 7 1/4" Product Travel 32" R 3 3/4" B.F. 1 1/2" B 6" 16" 32 1/8" End Drive B Section B - B 6 1/2" 1/4" 6 1/2" Standa B.F. Sec Interm B.F. + B.F 5"
ZONE CCUMULTION MODEL ZP ZERO PRESSURE CHIN DRIVEN ELECTRONICLLY CONTROLLED IR CLUTCH ZONE CCUMULTOR Medium duty zone accumulation of pallets, skids or drums ZERO PRESSURE CHIN DRIVEN ELECTRONICLLY CONTROLLED CCUMULTION SPECIFICTIONS Effective Widths 15 to 72 Specify Lengths 10 standard unit Varies per application Roller Size 2 1/2 dia. x 11 ga. with 11/16 hex shaft 2 5/8 dia. x 7 ga. with 11/16 hex shaft Roller Center 5 Specify Formed 7 ga. Drive 3/4 H.P. 230/460/3/60 1, 1-1/2, 2 HP 115/230/1/60, severe duty, Chain Drive #50 roll to roll, #60 zone to zone OPTIONS Roller Space - Consult factory, Roller Center - Consult Factory, Drive locations: as needed, Galvanized or stainless construction,, Speeds, Variable speed, Controls, Paint, end stop, Rollers set low, UHMW sleeves, higher capacity bearings, Zone lengths to suit, E-stop with pull cord, Knee braces, Supports - 6 @ #8.2 structural channel How the Conveyor Works Chain Driven Live Roller Conveyor is set up with individually controlled zones by installing electronic sensors at equal intervals along the conveyor. Power to individual zones comes from a main chain drive that runs the length of the conveyor. Each zone is driven off the main drive and activated or deactivated with an air operated clutch controlled by an electronic sensor. In normal operation, the discharge zone (zone #1) is electronically activated by an electrical solenoid (provided by Titan). When a load is placed on the conveyor, at the infeed, it travels the length of the conveyor to the discharge. t the discharge the load activates the electronic sensor which activates the air clutch and stops the load. t the same time, this disengages the clutch and moves a load into zone #2 to accumulate the next load placed on the conveyor. When the conveyor is to be unloaded, an external signal (NOT provided by Titan) is sent to the solenoid switch which engages the clutch in zone #1. This activates the zone rollers and moves the load toward the discharge. Once the load clears the electronic sensor, the second load moves forward from zone #2 to zone #1 and all other loads advance forward one zone. Titan Zone ccumulation Conveyors are designed to accumulate products and containers into zones without contact, commonly termed Zero Pressure ccumulation or ZP. vailable Plug & Go logic makes control easy and reduces cost. Titan offers designs compatible with all models and types of roller conveyors. The Model ZP is designed to handle heavy loads such as pallets, skids or drums. zone length is 60 with other zone lengths available. Rollers are 2 1/2 diameter x 11 gauge or an optional 2 5/8 x 7 gauge. roller spacing is 5 with other options available. ccumulation and load release can be either single or slug type and must be specified when ordered. controls are available to control accumulation and release modes, create intermediate load/unload stations and allow for time delay settings. Incoming power is 110 volt, single phase and then is converted to 24 volt DC for sensor and solenoid control. Styles: 1. Zones have individual conventional drives. 2. Zones are engaged by air clutch from a single drive. 3. Zones have individual motorized roller drives. OVERLL LENGTH ZONE #3 ZONE #2 ZONE #1 ELECTRONIC SENSOR #3 ELECTRONIC SENSOR #2 ELECTRONIC SENSOR #1 1 3/4" 1 1/2" E.W. 5 3/4" 16 1/4" MX. E.W. 1 1/2" 52" 1 1/2" MIN. 16" MIN. BOTTOM MOUNT DRIVE SECTION - SIDE MOUNT DRIVE
TRNSFER & COOLING SYSTEMS CHIN DRIVEN LIVE ROLLER TRNSFER/STOP Medium duty handling of pallets, skids and drums MODEL 525 CHIN DRIVEN LIVE ROLLER CONVEYOR SPECIFICTIONS Effective Widths 13 to 40 Specify up to 72 E.W. Lengths 5 min. 3 min., max. based on application Roller Size 2 Dia. x 11 ga. with 7/16 hex shaft - 580 lb. roller cap. Roller Center 5 2-13/16, 3-7/16, 4-3/8, 5-15/16, 10 Formed 7 ga. 6 C structural Drive 3/4 H.P. 230/460/3/60 1, 1-1/2, 2, 3 H.P. 230/460/3/60, severe duty, inverter duty, brake motor Chain Drive #50 roll to roll drive #60 available Roller Space - Consult factory, Roller Center - Consult Factory, Drive locations: as needed, Galvanized or stainless construction, H. P., Speeds, Variable speed, Controls, Coated rollers, Paint, multi-strand chain transfers, Pallet lifts, Pallet jack plates for side or end load, C Face brake and Fixed end stop, Rollers set low, UHMW sleeves, ccumulation sleeves, Knee braces, ir operated blade stop, Supports - 6 @ #8.2 structural channel, Overall Length 3 1/2" 21 15/16" 30" COOLING & DRYING BELT CONVEYOR Replaces water quench Reduce cool down time Custom designed from standard components COOLING/DRYING CONVEYOR Belt 1/2 x 1 Galv. Flat Wire Mesh Balanced weave, slat Widths 4 to 48 Specify Drive 1/2 H.P. 230/460/3/60 Drive to suit application Lengths 5 min. To suit application Formed 10 ga. To suit application H.P., drive location, speed, fixed or variable speed, controls, belt widths, deck wear strip options, cooling fans, center drive & take-up, galvanized, stainless, siderails, supports, transfer roller, bolt-on bottom pans, e-stop with pullcord, End View casters, special paint vailable Belt Widths: 12"- - 24"- 30"- 36"- 48" Unit Dimensions Custom Designed to Fit pplication Specifications Overall Length vailable Belt Widths: 12"- - 24"- 30"- 36"- 48" Unit Dimensions Custom Designed to Fit pplication Specifications 30" End View
HINGED STEEL BELT CONVEYOR Page 1 of 2 MODEL 610 Low profile machine tool Side mount drive Flared infeed side rails Liquid tight bottom pan TYPE 1 TYPE 2 TYPE 3 TYPE 4 MODEL 610 2-1/2 HINGED STEEL BELT CONVEYOR STNDRD OPTIONS Belt Widths 6, 8, 12, 18, 24 4, 10, 14, 16 Belt 2-1/2 pitch plain hinged steel with radial sidewings Perforated, pimpled, perforated & pimpled, impact plates Drive 1/2 HP 230/460/3/60 3/4, 1 HP, Severe duty, brake motor Speed 10 F.P.M. Specify Drive Location End drive side mount Top Mount Curves 30 0, 45 0, 60 0 Special Curves Motors, controls, welded barrels, paint color, customized infeed siderails, casters, coolant tanks, pumps, drain plugs, zero speed switches, Bulb type infeeds 6 11/16" 3 1/2" BW+3 27/32" BW-17/32" Section - Infeed Cross Section 12" Radius S REQ'D 10-45 B Drive Mounted on Far Side as 16 1/2" C C 2 1/2" Take-up 6 1/2" B 30, 45, 60 Std. MODEL 620 Low profile (7 high) vailable in 3 belt styles and low profile or powdered metal sidewing (1 high) MODEL 620-2-1/2 PITCH HINGED STEEL BELT MODELS Belt Width 4, 6, 8, 10, 12, 14, 16, 18, 24 30, 36, 42 Belt Type 2-1/2 pitch low profile or radial sidewing, 1500 # belt pull w/o sidebars, 3000 # w/ sidebars-std. on belts over 24 Curves 30 0, 45 0, 60 0 Perforated, pimpled, peforated & pimpled, welded barels, impact plates, sidebars on narrow belts 8 19/32" 6 11/16" Drain Holes BW-11/32" Section B-B Intermediate Cross Section Formed 12 Gauge 8 19/32" 7 9/16" BW BW+15 13/32" 10 1/2" Section C-C Discharge Cross Section 7 deep formed 10 ga. Drive 1/2 H.P. 230/460/3/60 3/4, 1, 1-1/2 H.P. 115/230/1/60, 575/3/60TEFC, severe duty, inverter duty, brake motor Drive Sprocket 5 Tooth, 4.25 P.D. Chain Pull 1,500# 3000# with sidebars Drive location, H.P., fixed and variable speed, zero speed switches, controls, tanks, chutes, plumbing, top covers, chip suppressors, 3 bolt flange bearings or t-slot bearings at infeed,casters, liquid tight bottom pans, paint, supports, Belt: pimpled, perforated, welded barrels, impact plates, wiper cleats, cleat heights, sidebars on narrower belts Many other options available, consult factory representative BW+4 1/4" BW 7" S REQ'D 8 1/2" CLER 2 1/2" TKE-UP 6" 14 1/2" MODEL 630 4 different configurations 6 tooth 5 P.D. sprockets Full profile 3 1/2" S REQ'D 12" RDIUS 30, 45, 60 STD. S REQ'D MODEL 630-2-1/2 PITCH HINGED STEEL BELT MODELS Belt Width 4, 6, 8, 10, 12, 14, 16, 18, 24 30, 36, 42 Belt Type 2 1/2 pitch 1-1/2 standard stamped sidewing Perforated, pimpled, pimpled & perforated, welded barrels, impact plates Curves 30 0, 45 0, 60 0 8-5/8 deep formed 10 ga. Drive 1/2 H.P. 230/460/3/60 3/4, 1, 1-1/2, 2 H:, 115/230/1/60, 575/3/60 severed duty, inverter duty, brake motor Drive Sprocket 6 Tooth, 5 P.D. Chain Pull 1500# without sidebars 3000# with sidebars OPTIONS Drive location, H.P., fixed and variable speed, controls, coolant tanks, chutes, plumbing, top covers, chip suppressors, casters, liquid tight bottom pans, 3 bolt flange bearings or T-slot bearings at infeed, paint, supports, Belt: pimpled, perforated, welded barrels, impact plates, wiper cleats, cleat heights, sidebars on narrower belts 4 1/4" 7" 3" Side Mount Drive ( Std.) 12" Radius 7 9/16" 7/8" 8 1/8" Clear 30, 45 & 60 Std. 2 1/2" T.U. ( Std.) (12" Min.) 6 3/4" 13 3/4"
HINGED STEEL BELT CONVEYOR Page 2 of 2 MODEL 640 pplications warranting heavy duty cycle Meets Heavy Duty automotive and foundry applications Economical 2-piece belt construction MODEL 640 HINGED 4 PITCH HINGED STEEL BELT CONVEYOR SPECIFICTIONS Belt Width 6, 8, 10, 12, 16, 18, 24, 30 48, 60 Belt Type 4 pitch, 10 ga. apron, 3 high 7 ga. stamped sidewings, 2 dia. flanged rollers, Perforated, pimpled, perforated & pimpled, welded barrels, impact plates, Curves 30 0, 45 0, 60 0 15 deep formed 10 ga. Drive 1/2 H.P. 230/460/3/60 3/4, 1, 1-1/2, 2, 3 H.P. 230/460/3/60, 115/230/1/60, 575/3/60 TEFC, severe duty, inverter duty, brake motor 15" + 6 7/8" - 1/4" 14" Clear 20" to 23" Drive Sprocket 6 Tooth, 8 P.D. Chain Pull 6000# Drive location, H.P., Fixed and variable speed, Impact rails on infeed frame, T-slot bearings, customized siderails, wiper cleats, cleat heights & centers, infeed hoppers, casters, Liquid tight bottom pans, coolant tanks, plumbing, top covers, drain plugs, paint, supports, Consult factory for special applications and construction of belt. 15" Radius 7 1/2" 30, 45 & 60 Std. 11 1/2" 24" Std. Discharge 4" T.U. MODEL 660 Rugged steel for large scrap handling 3 diameter, bushed single flange roller Double outside side bar and 3/4 thru axle Designed for years of maintenance free operation in the most hostile conditions MODEL 660-6 PITCH HINGED STEEL BELT CONVEYOR SPECIFICTIONS Belt Width 12, 14, 16, 18, 24, 30, 36, 48 60, 72 Belt Type 6 pitch x 1/4 apron, 4 high 1/4 thick radius sidewings, 3 dia. flanged rollers perforated, pimpled, piimpled & perforated, welded barrels, impact plates, cleat heights and centers Curves 30 0, 45 0, 60 0 21 deep formed 7 ga. 25 deep formed 7 ga. Drive 3/4 H.P. 230/460/3/60 1, 1-1/2, 2, 3, 5, 7-1/2 HP, 115/230/1/60, 575/3/60 TEFC, severe duty, inverter duty, brake motor Drive Sprocket 6 Tooth, 12 P.D. Chain Pull 8,900# 20" Radius 11 1/4" Drive location, H.P., Fixed and variable speed, zero speed switches, Impact rails on infeed frame, T-slot bearings, customized siderails, infeed hoppers, casters, Liquid tight bottom pans, coolant tanks, pumps, drain plugs, top covers, paint, supports, Consult factory for special applications and construction of belt. 17" (36" Minimum Infeed) 9" T.U. 30, 45, & 60 Std. QUENCH CONVEYOR Liquid tight horizontal tank Cooling or quenching heavy duty parts Consult factory for construction parameters and applications 24" Min. Discharge STNDRD CONVEYOR PROFILES TYPE 1 TYPE 2 TYPE 3 TYPE 4
REPLCEMENT HINGED STEEL BELT 2 1/2 PITCH EXCLUSIVE TITN RDIL SIDEWINGS Developed for extremely small objects The opening between sidewings and apron is reduced to a maximum of.010. Tight tolerance is maintained regardless of direction of belt flex 2 1/2 PITCH HSB-STMPED SIDEWING Developed to handle stamping, metal scrap, ships, turnings, castings and parts hot or cold - this belt is designed for hostile applications vailable in pimpled, perforated, plain or pimpled/perforated apron Belt is modified with impact plates, welded barrels or heat dissipating plates Consult factory for list modifications Chain pull #1200 - #2500 (with side bar) 12 ga. apron 2 1/2 PITCH BLNCED WEVE METL BELT vailable in galvanized, Hi Carbon & stainless steel High temperature applications Various mesh openings available Consult factory for other options 2 1 2 " 13 4 " 3 16 " MIN. REVERSE BEND 5" R 1" 1 2 3 4 5 #12 G. DECK D B C 7 16 " XLE COTTER PIN STD. 1 8 " 3/4" 1 8 " 1 1 2 " NO. PLTE STYLE 1 Hinge Plate Plain 2 Hinge Plate Pimpled 3 Hinge Plate w/impact Bar 4 Hinge Plate Perforated 5 Hinge Plate Pimpled & Perforated 2 1 2 " 2 1 4 " MIN. REVERSE BEND 10 1/4 1 1/2" 1 2 3 4 5 #12 G. DECK D B C 7/16" XLE 1/8 " COTTER PIN STD. 3/4 " 1/8 " 1 1 2 " NO. PLTE STYLE 1 Hinge Plate Plain 2 Hinge Plate Pimpled 3 Hinge Plate w/impact Bar 4 Hinge Plate Perforated 5 Hinge Plate Pimpled & Perforated 4 PITCH CLOSE TOLERNCE HSB heavy duty 10 ga. apron with 3 high 7 gauge sidewing 1/2 diameter axle with 3/4 bushing 2 diameter single flange through hardened sintered metal roller Plain, pimpled, perforated or impact apron #4000 chain pull with sidebar 1 3/4 diameter single flange or flat face roller available 6 PITCH HINGED STEEL BELT Extra heavy duty 1/4 apron with 4 high, 1/4 sidewing 3/4 diameter axle with heavy duty bushing 3 single flange through hardened sintered metal roller Plain, plain w/impact plate, perforated, double perforated, pimpled, or pimpled/perforated apron #8900 chain pull with sidebar 1 3/4 diameter flat face roller available Welded sidewing available The next time you have a belt failure of replacement need, regardless of the conveyor manufacturer, call Titan and get a price on our competitor replacement belts. phone call may save you downtime and dollars at the same time 3 5/8" OR 3 7/8" 1 3 4 " 1" MIN. REVERSE BEND 17 3/16 " 3" STD. COTTER PIN STD. NO. PLTE STYLE 1 Hinge Plate Plain 2 Hinge Plate Perforated 3 Hinge Plate Double Perforated 4 Hinge Plate w/impact Bar 2 1 4 " MIN. REVERSE BEND 24" R SUGGESTED BEND 28" R 1 B 1 C1 4" COTTER PIN STD. 1 1 16 " 2 1 2 " TITN INDUSTIES NEW LONDON WI. 1 2 TITN INDUSTIES NEW LONDON WI. 3 4 1 2 3 TITN INDUSTIES NEW LONDON WI. TITN INDUSTIES NEW LONDON WI. TITN INDUSTIES NEW LONDON WI. 4 5 6 TITN INDUSTIES NEW LONDON WI. TITN INDUSTIES NEW LONDON WI. NO. PLTE STYLE 1 Hinge Plate Plain 2 Hinge Plate Perforated 3 Hinge Plate Double Perforated 4 Hinge Plate Pimpled 5 Hinge Plate Perforated & Pimpled 6 Hinge Plate w/impact Bar 6" TITN INDUSTIES NEW LONDON WI. 4" 1 1 8 " 1 2 " XLE 10 G. DECK B C 3 4 " TUBE 3 16 " 3 1" 8 " 2" 2 1 2 " 5 1 2 " 2" 3 4 " XLE 1 4 " DECK C B 15 16 " TUBE 1 2 " 2" 1 1 8 " 3" 3 3 4 "
SLT CONVEYORS MODEL 696 SLT CONVEYOR Unique system for special handling Heavy duty assembly line system Flat surface and stable movement Many specialty types of surface modifications can be made to handle heavy duty items in a special way MODEL 696 SLT CONVEYOR SPECIFICTIONS Slat Widths 12, 18, 24 30, 36, 48, 60, 72 Drive H.P. to suit application Speed 30 f.p.m. Specify speed required Slats Formed 7 ga. HD steel plate, wood, UHMW covered Formed 7 ga. Belt 6 pitch (SR196 chain) 4 pitch (SR194 chain) Drive location, H.P., speed, Slat widths to 72, fixtures mounted on slats, Belt - 4 pitch (SR194), work leaves, push offs, fixtures mounted on slats, special paint Overall Length Center to Center of Sprocket Length 5 3/4" 1/16" 12" P.D. 36" Min. Radius 5 1/2" 1" Thk. Hardwood Slat 3/8" or 1/2" P L Slats 12" P.D. Horizontal to Incline Slats 15.68" P.D.
DRG CHIN CONVEYORS MODEL 670 DRG CHIN CONVEYOR Heavy duty cycle units Fines recovery systems 2 1/2 pitch chain Consult factory for special applications MODEL 670 DRG CHIN STEEL BELT MODELS Belt Width 4, 6, 8, 10, 12, 14, 16, 18, 24 30, 36, 42 Belt Type 2-1/2 pitch chain Curves 30 0, 45 0, 60 0 8-5/8 deep formed 10 ga. Drive 1/2 H.P. 230/460/3/60 3/4, 1, 1-1/2, 2 HP 115/230/1/60, 575/3/60, TEFC, severe duty, inverter duty, brake motor Drive Sprocket 5 Tooth, 4.25 P.D. Chain Pull 2,500# 2,500# Drive location, H.P., fixed and variable speed, controls, tanks, chutes, plumbing, top covers, chip suppressors, casters, liquid tight bottom pans, paint, supports Many other options available, consult factory representative + 4 3/8" 8 5/8" 2 3/4" 6 1/2" SECTION - + 9 1/4" SECTION B-B B S REQ'D 2 1/2" S REQ'D 6 3/4" B S REQ'D 4 1/4" 30, 45, 60 STD
TURN TBLES MODEL 200 TURNTBLE SPECIFICTIONS TITN TURN TBLES Consult factory for various applications and design criteria Diameter Customer can specify Drive 1/2 H.P. 230/460/3/60 1, 1-1/2, 2 HP, 115/230/1/60 Severe duty, inverter duty, brake motor Table Top 7 gauge Others available Drive Location Bottom mount drive Speed 2.5 RPM fixed Fixed speeds - specify, variable speed with DC motor & SCR controller or C inverter OPTIONS H.P., variable speed, controls, siderails, air operated, conveyor on top, roller or skate wheel approaches, galvanized, stainless, special paint Many other options available - consult factory Flat surface base Rotation Flat Surface Base Turn Table Roller pproaches 6" Dia. Siderails Specify Height Required Expanded Metal Guarding Four Sides 20" Min.
WIRE MESH/PLSTIC BELT CONVEYOR MODEL 124 WIRE MESH BELT CONVEYOR multi-functional load carrying belt whether you re drying, cooling, oiling or just have a hot part Many different mesh configurations are available from many sources Three different beds - UHMW, roller or wear strip sliders are available depending upon loads and installation MODEL 124 WIRE MESH BELT CONVEYOR Belt Widths 12, 18, 24, 30, 36 4, 6, 8, 10, 14, 16, 20, 40, 42, 48 Lengths Belt Type 5 min., max. based on application 1/2 x 1 galvanized flat wire mesh Drive 1/2 H.P. 230/460/3/60 Woven wire, balanced spiral, chain edge, stainless steel, high carbon or plastic 3/4, 1, 1-1/2, 2 HP, 150/230/1/60, TEFC, washdown, severe duty, inverter duty, brake motor Speed 60 f.p.m. fixed speeds, variable speed Drive Sprocket 13 tooth, 4.4 P.D., H.D., Keyed Formed 10 ga. Deck Longitudinal steel wear strips Herringbone deck, roller deck H.P., drive location, speed, fixed or variable speed, controls, belt widths, deck wear strip options, cooling fans, center drive & take-up, galvanized, stainless, siderails, supports, transfer roller, bolt-on bottom pans, e-stop with pullcord, casters, special paint Roller Bed Deck Tail Section Overall Length Drive Section B C 5/8" BELT OPTIONS - CONSULT FCTORY B 8 1/2" 9" C +7 1/2" Section - 6 1/2" +4" +1" Section B-B 4 1/8" 2" Section C-C 8 1/2" Flat Wire Wear Strip Deck Tail Section Overall Length Drive Section B C 5/8" Plastic B 8 1/2" 9" C +5 1/8" +4" +1" 4 1/8" 2" 6 1/2" 6 1/2" 8 1/2" Balance Weave Section - Section B-B Section C-C
BLL TRNSFER TBLE MODEL BTT BLL TRNSFER Manually rotating, shifting, turning or positioning at work stations Feed tables for machinery or assembly processes BLL TRNSFER TBLE SPECIFICTIONS Bewteen From 10 to 42 Specify Length From 12 in 12 increments Specify 3-1/2 deep 10 ga. Ball Centers 3 2, 4, 6 Mount 1/4 stud mount Flange mount Capacity 50 lb. per ball carbon steel, stainless, nylon, spring loaded, ball pattern & centers - consult factory STGGERED PTTERN BLL CENTERS BLL CENTERS OVERLL LENGTH STD. LENGTHS IN 12" INCREMENTS 3 1/2" B.F.+3" B.F. 1/4"
SOLID WSTE HNDLING MODEL 661 CHIN EDGE CONVEYOR Built to the same rugged standards as scrap handling Model 660 Sandwich a heavy duty PVC belt bottom stabilizer bar and square tube welded cleat for strength and performance Load is carried on 3 flange rollers and UHMW wear strips to provide large capacity with minimum horsepower requirements MODEL 661 SPECIFICTIONS Belt Widths 12, 18, 24 30, 36, 48, 60, 72 Belt Type 6 Pitch Chain Edge PVC, 3 dia. flanged rollers, 3 formed cleats Curves 30 0, 45 0, 60 0 Formed or Open style with access panels Drive 3/4 HP 230/460/3/60 1, 1-1/2, 2, 3, 5, 7-1/2 HP 115/230/1/60, 575/3/60, TEFC, severe duty, inverter duty, brake motor Drive Sprocket 8 Tooth 12 P.D. Belt width, drive, drive location, fixed or variable speed, controls, infeed hopper, customized siderails, bolt-on bottom pans, access panels on side frames, open style frame available, chain oilers, supports, paint : Belting - Consult factory 12", 24", 36", 48" 60" Min. E.W. + 25 3/4" 7 3/8" E.W. 12 7/8" 25 3/4" Min. Section - 60" Min. Infeed T.U. 27" Min. 30, 45 Std. Consult Factory for custom system layouts to meet your individual needs.
MULTI-STRND CHIN CONVEYOR MODEL 680 Multi-Strand Chain Conveyor Designed for extra heavy duty product movement Space between chain strands can accommodate other control or process devices Consult factory for options and applications MODEL 680 MULTI-STRND CHIN CONVEYOR Chain (2) strands of C2060 C2080, multiple strands available Capacity 2,400 lbs 4,000 with (2) strands C2080 Drive 1 HP 230/460/3/60 Horsepower to fit application Formed 7 ga. Structural Chain Speed 30 F.P.M. Specify Drive location, HP, speed, variable speed available, controls, multiple chain strands, paint BELT WIDTH + 9 3/8" 6" BELT WIDTH C - C 3 3 8 " 5 3 4 " 8 1 2 " SECTION - SECTION B-B 6" BELT WIDTH + 9 3/8" BELT WIDTH C - C 3 3 8 " 5 3 4 " 8 1 2 " INFEED SECTION OVERLL LENGTH DRIVE SECTION SECTION - SECTION B-B 14" B 1 13 32 " 8 1 2 " STD. IC60 REDUCER 9 9 32 " 20" MINIMUM W/BOTTOM MOUNT DRIVE B OVERLL LENGTH INFEED SECTION DRIVE SECTION 14" B 1 13 32 "
PLLET PRO CONVEYOR PLLET PRO CONVEYOR Heavy duty plastic belt Ideal for irregular, imperfect or peg type pallets End or side loading Minimum transfer gaps MODEL PLLET PRO SPECIFICTIONS Belt Widths 12 to 62 3/4 Lengths Belt Type Per application Plastic, Uni-Belt Drive 1 H.P. 230/460/3/60 Deck OPTIONS 4 3/4 deep 7 gauge 7 ga., U.H.M.W. top Drive location, drive sprockets, speeds, controls, galvanized or stainless construction, supports, belt type, paint BOTTOM MOUNT DRIVE SIDE MOUNT DRIVE BOTTOM MOUNT DRIVE BOTTOM MOUNT DRIVE SIDE MOUNT DRIVE SIDE MOUNT DRIVE OVERLL INFEED WIDTH OVERLL BELT INFEED WIDTH OVERLL +5 WIDTH 1/4" INFEED BELT WIDTH +5 BELT 1/4" WIDTH +5 1/4" OVERLL LENGTH 2" 2" IC-45=13" OVERLL LENGTH IC-60=13 3 8" 2" OVERLL LENGTH 2" IC-70=14 4" 1 IC-80=14 IC-45=13" 8" 2" 2" IC-60=13 3 8" IC-45=13" IC-70=14 4" 1 IC-60=13 3 IC-80=14 7 8" 8" IC-70=14 4" 1 IC-80=14 7 8" 5 7/8" BELT WIDTH 2 1/8" 5 7/8" BELT WIDTH 2 1/8" 5 7/8" BELT WIDTH 2 1/8" OVERLL LENGTH 2" 2" OVERLL LENGTH 2" OVERLL LENGTH 2" 2" 2" BELT TKE-UP 7 7/8" 7 7/8" 7 7/8" BELT TKE-UP 11 3/4" BELT WIDTH 2 1/8" BELT TKE-UP 11 3/4" BELT WIDTH 2 1/8" 11 3/4" BELT WIDTH 2 1/8" 1 1/2" 1 1/2" 4 3/8 1 1/2" 4 3/8 4 3/8 BELT WIDTH + 4 1/4" BELT WIDTH + 1 1/4" BELT WIDTH BELT WIDTH + 4 1/4" BELT WIDTH + 1 1/4" BELT WIDTH + 4 1/4" BELT BELT WIDTH WIDTH + 1 1/4" BELT WIDTH 1/16" 1/16" 1/16"
SUPPORTS SUPPORTS or Heavy duty available Channel supports available Knee brace available SMILE BRCKET SPREDER UPPER SUPPORT LOWER SUPPORT KNEE BRCE FOOT FLOOR SUPPORT Support Micro adjustable, Pedistal support or Tilt support available on certain models (Consult factory for details) STNDRD SUPPORTS (12 G. FORMED) EXTR DUTY SUPPORTS (7 G. FORMED) Support # Min. Height Max. Height Support # Min. Height Max. Height 0 12 13-1/2 ED0 12 13-1/2 1 13 16 ED1 13 16 2 16 20 ED2 16 20 3 19 25 ED3 19 25 4 24 36 ED4 24 36 5 34 46 ED5 34 46 6 44 56 ED6 44 56 7 54 66 ED7 54 66 8 64 74 ED8 64 74 9 72 82 ED9 72 82 10 80 90 ED10 80 90 11 88 98 ED11 88 98 12 96 106 ED12 96 106 13 104 114 ED13 104 114 If 4 dia. casters are used, add 5-1/4 to dimensions shown above. If 6 casters are used, add 7-3/4 to dimensions shown above. Support elevations adjustable to +/1 from defined height. ll minimum and maximum height dimensions given are for supports only.
CONTROLS & CCESSORIES Page 1 of 3 MNUL NON-REVERSING STRTER Single phase - 110 volt or 230 volt Built-in start/stop pushbuttons NEM enclosure Overload protection MNUL DRUM REVERSING SWITCH Single phase - 110 volt or 230 volt NEM enclosure Lever actuated: FWD/REV/STOP MGNETIC STRTER 3-phase - 230 bolt or 460 volt Reversing or non-reversing NEM enclosure Built-in Start/Stop or FWD/REV/STOP Overload protection 110 volt control transformer VRIBLE SPEED SCR CONTROLLER Single phase - 230 volt or 460 volt To be used with 90 volt or 180 volt DC motor Reversing or non-reversing Built-in Start/Stop or FWD/REV/STOP pushbuttons NEM enclosure VRIBLE SPEED C INVERTER 3-phase - 230 volt or 460 volt Reversing or non-reversing Built-in FWD/REV/STOP pushbuttons NEM enclosure Overload protection 110 volt control transformer PHOTO EYE EMERGENCY STOP PULL CORD SWITCH MOTOR BRKE UNIT When power unit and hold in place function are required
CONTROLS & CCESSORIES Page 2 of 3 NGLE END STOP ngle End Stops are constructed of 2 x 2, 1/4 thick angle painted steel and are used for 2-1/2 and 2-5/8 gravity conveyor models. The angle mounts to the end of conveyor for stopping boxes and cartons. vailable in all standard conveyor widths. GTES Manual gates can be used with a 1.9 and 2-1/2 dia. gravity roller conveyor. Gas assist spring balanced gates also available. Gates provide a passageway for personnel, lift trucks and other equipment. HND OPERTED BLDE STOP Hand Operated Stops are used where manual line control is required, such as assembly workstations, shipping areas, and so on. Lever to raise or lower stop can be used in normally up or down positions (supplied shown). Stroke is 1-7/8 above rollers. Construction: Blade - 7 ga. steel angle 1 x 1-1/2. Capacity - ll are live load capacities at 65 feet per minute. Blade - 150 lbs. CSTERS Casters are easily bolted to floor supports for portable applications. 4 or 6 diameter Rubber or steel Wheel Swivel or rigid Brakes available Load Height and Swivel Radius 4 dia. Caster - 5 5/8 & 3 9/16 6 dia. Caster - 7 1/2 & 5 Knee brace recommended for portable applications IR OPERTED BLDE STOP ir operated stops are used where automatic line control is required, such as assembly workstations, shipping areas, and so on. Stop is supplied for use normally down. TURNING WHEELS Turning wheels are used in converging 30 0 and 45 0 spur applications. lso use at 90 0 transfers where Traffic Cops, Package Stops, and other product flow controlling devices are used. Wheel is mounted on adjustable bracket to insure proper package orientation through transfer. Can be mounted to slider bed or side channels of powered or gravity conveyors. 6 Diameter Turning Wheel. CEILING HNGERS Ceiling hangers provide a safe and effective method of attaining high conveyor elevations. Used when maximum utilization of floor space is needed or when required height exceeds support capacity. Customer is responsible for verifying with a structural engineer that the ceiling capacity will support both the conveyor and product weight. Recommended verifying fire code clearance requirements before installation. LIVE ROLLER WLKWY PLTES Deck plates between roller spacing offer safety and deck access. KNEE BRCES - SMILE BRCKETS Knee braces add strength to permanent supports and stability to portable applications. The adjustable support bracket allows support to be attached easily to conveyor. djustable Support Bracket - 7 ga. construction.
CONTROLS & CCESSORIES Page 3 of 3 Hinged Steel Belt Titan offers a variety of belt options for hinged steel belt Models 610, 620, 630, 640 & 660. Pimpled & Perforated Pimpled Perforated Plain Cleated-Divided-Segmented Outside Sidebars-Impact Plates Discharge Chutes Siderails & Hoppers Drain Plugs, Drain Holes & Tanks Step Plates Drive Packages
ENGINEERING DT ROLLER CENTER SPCING In order to convey your product smoothly and efficiently, it must be supported by a minimum of three rollers. To compute the center to center roller spacing required, divide the length of your package by 3. The dividend is your required spacing. For example, a package 36 long when divided by 3 would give a dividend of 12. Therefore, the required spacing would be 12 center to center. Flexible bottom packages require four or more supporting rollers per package. Carton Length Carton Height 1/3 1/3 1/3 Commodity WEIGHT (lbs) OR COMMENT CRTONS 1-5 5-15 15-20 CRTES 20-50 50-100 100--250 BEVERGE CSES Diagram 1 EMPTY FULL Center of Gravity PLIN OR DUST- PROOF BERINGS Determining Factors on Box Tumbling 1. Draw Conveyor angle of incline 2. Draw box size on conveyor 3. Draw Diagonal line to find center of box 4. Divide lower portion of box into thirds 5. Draw vertical line as shown 6. If vertical line falls within the lower third (See diagram #1) the box may tumble depending on weight distribution 7. If vertical line falls within the upper two thirds (see diagram #2) the box will not tumble. Grade Suggestions GRESE PCKED BERINGS 9 7-1/2 6 9 5 4-1/2 4 Carton Height Carton Length Conveyor Incline ngle 1/3 1/3 1/3 7-1/2 6-1/2 5 6 5 7-1/2 Diagram 2 Center of Gravity Commodity WOOD CSES TOTE PNS BRRELS WEIGHT (lbs) OR COMMENT 20-50 50-100 100-250 50-100 100-250 250-500 EMPTY FULL PLIN OR DUST- PROOF BERINGS 5 4-1/2 4 4 3-1/2 3 5 4 GRESE PCKED BERINGS 7-1/2 6-1/2 5 6-1/2 5 4-1/2 6-1/2 5 LUMBER STD. BORD 5 7-1/2 BRICK 5 6-1/2 General guideline rate of fall chart for flow on gravity roller conveyor. Exact rate of fall should be determined at time of installation with actual product to be conveyed. Gravity Roller Rate of Fall Chart Product - With Conveyable Underside Surface Weight Range in Pounds Fall in 10-0 Cartons 1 to 5 8 to 9 Cartons 5 to 15 7 to 8 Cartons 15 to 50 6 to 7 Cartons 50 to 75 5 to 6 Wood Boxes 20 to 50 5 to 6 Wood Boxes 50 to 150 4 to 5 Wood Boxes 150 to 200 3 to 4 Steel Tote Boxes 15 to 50 3 to 4 Grades, recommended here are not exact and should be used only to estimate your requirements. Figures at left are intended for average conditions, using proper size rollers for materials handled. dditional grade may be required in some cases. Starting a package from rest on level lines requires a push of approximately 3% of the total load. For heavy loads, a pitch of 18 per foot will reduce push required. The amount of drop required for 90 0 curves with 4 inside radius is approximately the same as required per 10 section. 20' Incline Conveyor Length 10' Net Lift 30 DEGREE OF INCLINE 17'-3" Horizontal Floor Space