SUSPENSION/STEERING/BRAKES/REAR AXLE

S12/1 S12/1 SUSPENSION/STEERING/BRAKES/REAR AXLE ENERGY SUSPENSION- BODY MOUNTS... S12/1 IDIDIT- TILT STEERING COLUMNS... S12/1 FRONT SUSPENSION- ENERGY suspension bushes... S12/3 HEIDTS-FRONT SUSPENSION aftermarket style... S12/5 STEERING-Performance... S12/8 BRAKES-performance... S12/8 REAR SUSPENSION original type inc ENERGY suspension bushes... S12/10 HEIDTS-REAR SUSPENSION [4-LINK] aftermarket style... S12/11 AIR-RIDE- REAR SUSPENSION aftermarket style... S12/12 AIR-RIDE- CONTROL- COMPRESSOR & TANK kits... S12/12 AIR-RIDE FRONT SUSPENSION aftermarket style...s12/13 REAR AXLE & PARTS...S12/13 SHOCKABSORBERS... S12/14 Body Mounts Polyurethane body mount set-black Chevrolet full Size Energy Suspension Polyurethane performance components, are made in the USA. Energy use a material called Hyper-Flex, which is the result of 20+ years of experience. Careful selection of material firmness [durometer] is used for each specific application on the vehi cles suspension & frame. Hyper-Flex components do not rot or deteriorate from exposure to oils & under-car chemicals or atmospheric conditions, like smog & ozone. Handling & steering response is vastly improved over standard, soft bushes. Ride could be stiffer. Polyurethane body [subframe] mount set-black Chevrolet Camaro BY3-4106G 1955-57 Not 2dr hardtop... 68.95 BY3-4120G 1955-57 2dr hardtop... 68.95 BY3-4138G 1965-70 2dr hardtop... 65.70 BY3-4142G 1967-2002 all models Black... 86.58 Chevrolet Corvette Polyurethane body mount set-black BY3-4153G 1963-64 Seat belt mounts... 26.26 BY3-4102G 1963-67 Hardtop only... 34.48 [part above is pictured] BY3-4152G 1963-67 Convertible only... 47.76 BY3-4126G 1973-82 All models... 54.83 Chevrolet Chevelle, Malibu, Monte-Carlo, Laguna, El-Camino Polyurethane body mount set-black BY3-4128G 1964 Not convertible... 91.99 BY3-4111G 1965-67 Not convertible... 91.99 BY3-4115G 1968-72 Not convertible... 68.95 BY3-4134G 1970-72 Monte-Carlo not convert 74.33 Polyurethane body [subframe] mount set-black Pontiac Firebird & Trans Am BY3-4142G 1967-75 check below... 86.58 BY3-4144G 1976-81... 95.86 Steering Columns The IDIDIT steering column is world renowned, and since 1986 has been fitted to many thousands of Hot-Rods, all over the world. IDIDIT is a family business, based in the state of Michigan, and their steering columns are made in the USA, to very high standards. Vari ous finishes are available, although we only carry in stock- chrome & paintable-steel. Other finishes, like- black powder coated, brushed & polished aluminium, are available to order. These columns are available in plain, 8 position tilt and with or without column shift. Measuring your car, to see which column would be best, is critical. Please ask for measur ing instructions and we will gladly send them to you. More time spent doing this, will ensure a perfect fit later on. Most columns feature a flashing indicator control, a 4-way hazaard light control & horn. Other options including cruise control are available. Tilt Steering Column Paintable Steel-Universal Does NOT have column shift Made by iditit- BYAJW265 28 length, 2 tube OD... 453.32 BYAJW255 30 length, 2 tube OD... 370.91 BYAJW245 32 length, 2 tube OD... 452.14 Tilt Steering Column PAINTABLE Steel-Universal HAS column shift Made by iditit- Does NOT have column shift Made by iditit- Tilt Steering Column Chrome-Universal BYAJW270 28 length, 2 tube OD... 430.88 BYAJW260 30 length, 2 tube OD... 595.44 BYAJW250 32 length, 2 tube OD... 603.78 Tilt Steering Column CHROME-Universal HAS column shift Made by iditit- BYAJW605 30 length, 2.25 tube OD 569.72 BYAJW585 33 length, 2.25 tube OD 694.50 BYAJW610 30 length, 2.25 tube OD 922.22 BYAJW615 33 length, 2.25 tube OD 892.48 Iss58

S12/2 S12/2 Steering Tilt Steering Column Paintable Steel-1955-56 Chevy This column HAS column shift If you retain the original manual steering box, you will need to chop off the inner shaft and re shape to take a coupler. An installation kit may be required. Has provision to use original dash indicator. Only works with 3 & 4 speed, not Powerglide. Made by iditit- BYAJW185 1955-56 Chevy... 408.58sp Tilt Steering Column Paintable Steel -1967-69 Camaro Does NOT have column shift. A 1969 Camaro steering wheel, bolts directly to the IDIDIT column. It is recommended you fit a new rag joint connection. Made by iditit- BYAJW050 1969 Camaro-w/ignition... 371.35sp Tilt Steering Column- Chrome- Ford Mustang These columns are for floor shift only. Designed for your classic Mustang. Save and use your original under dash mount. A new floor mount comes with the column. Complete with a Ford turn signal switch, and a Ford type wiring plug. Designed to accept your original Mustang steering wheel, and place it in the original position. You could use an alternative steering wheel with an adaptor. The lower shaft is 3/4 x 36. For the 1965-66 and some 67 models you will need a coupler BYAJW195. You will also need to cut off your old shaft, which goes into the steering box, & modify it to 3/4 DD. Later 67 and 68 use kit BYAJW880. The 1969 model uses a Rag Joint BYAJW885. Made by iditit- BYAJW860 1965-66 Mustang... 610.63 BYAJW865 1967 Mustang... 559.51 BYAJW870 1968 Mustang- collapsible 670.82 BYAJW875 1969 Mustang- collapsible 684.70 Steering Column Accessories/Installation Parts Budget Floor Mount With Trim Kit This lower bracket comes with a polished aluminium trim ring & hardware. To complete the installation, a boot is also available. BYAJW105 Floor mount trim kit 2 tube 45.42 BYAJW110 Black boot for above kit... 20.44 Pivoting Drop Brackets-Polished Aluminium Often required to hold the steering column in place, at the right angle, where the original part will not work. BYAJW070 2 tube, 2-1/2 drop... 105.92 BYAJW075 2 tube, 3-1/2 drop... 105.92 BYAJW080 2-1/4 tube, 2-1/2 drop... 106.12 BYAJW515 2-1/4 tube, 5 drop 1932 Ford 75.83 BYAJW830 Upper mount bracket... 12.05 Use this metal bracket on a 47-54 Chevy P/U Cruise Control Kit Includes the parts needed to fit cruise control on a non computerised engines. Servo & control unit are small enough to fit under any dash. Includes pulse generator & control handle. Add this worthy item to your column. BYAJW160 Cruise control kit... 336.58 BYAJW165 Cover-cruise handle-alum pol.. 30.36 Floor Mounts for Column In some cases, the original bottom column mount, will not work with your new column. BYAJW170 2 tube budget floor mount 36.84 BYAJW115 2-1/4 tube budget floor mount 36.34 BYAJW190 2 tube budget Tr-Chevy 18.53 BYAJW175 2 swivel ball floor mount 149.89 BYAJW500 2-1/4 swivel ball floor mount 151.99 Above numbers [BYAJW175/500] are for a chrome stg column BYAJW510 2 swivel ball floor mount 151.99 BYAJW505 2-1/4 swivel ball floor mount 151.99 Lever with Dipswitch [High Beam] Control your high beam, or similar item from your flashing indicator lever. Female Plug for IDIDIT Steering Column-3-7/8 This 3-7/8 plug mates up to the plug on some IDIDIT steering columns. Please check this will fit your column before purchase. This plug enables you to wire up your column using a proper plug. BYAJW140 Female plug 3-7/8... 22.75 BYAJW065 Lever with switch... 132.06 Indicator for Transmission Enables you to see which gear you are in. Mounts on top of column. BYAJW120 Acrylic indicator +pointer 3spd... 32.47 BYAJW125 Acrylic indicator +pointer 4spd... 24.65 BYAJW130 Also includes chrome housing 3spd 92.11 BYAJW135 Also includes chrome housing 4spd 89.14

S12/3 S12/3 Steering/Front Suspension Cable Shift for Column Change This kit enables you to connect up your new column to your automatic trans. Consists of- cable, transmission bracket and cable bracket for column. BYAJW090 GM Trans 69 on, IDID 2 143.27 BYAJW095 GM Trans 69 on, IDID 2.25 155.92 INSTALLATION KITS Listed below, are the installation parts for the IDIDIT column, [version that uses the OE steering wheel] for the 1965-69 Ford Mustang. BYAJW195 Coupler 3/4 x 36 //3/4 DD 68.56 1965-early 67. On these vehicles, the steering staft comes out of the steering box and up into the column [one piece]. To fit a different column, this shaft will need to be cut, & then modified to take the coupler. BYAJW880 Kit later 67 and 68... 181.87 Consists of a coupler, short piece of connecting shaft, & a rag joint. BYAJW885 Rag joint for 69... 122.30 This is a flexible coupling to join the column to the OE stg box. BYAJW625 C4/C6 Link clamp assy 2.25 55.76 BYAJW630 C4 Trans bracket/cable kit 90.96 BYAJW640 C6 Trans bracket/cable kit 96.90 BYAJW620 Half moon shift lever 40.43 The half moon shift lever will help you avoid the brake pedal. The lever is complete with bushing & hardware to mount to your IDIDIT steering column. Coupling Parts for Steering Rack/Box There are many types of coupling to join your column to your steering rack/ box. Here are some of them-others available to order- BYAJW988 Shaft support 3/4 37.49 The above support is required where 3 u/j s are being used BYAJW750 UJ steel 3/4 DD to 26 x 9/16 116.86 Above joint is for Heidts manual stg rack BYAJW495 UJ steel 36 x 3/4 to 3/4 DD 126.00 Above joint is for Heidts power stg racks with 36 x 3/4 pinion BYAJW645 UJ steel 1 DD to 3/4 DD 115.68 BYAJW565 Pol S/S u-jnt 1 DDx3/4 DD 165.58 BYAJW595 U-joint steel 3/4DD to 3/4DD 110.84 BYAJW600 UJ steel Mustang V to 3/4DD 96.26 Above joint is for power stg racks with Mustang V pinion BYAJW535 u/j pol S/S Must V x3/4 DD 196.70 The above joint has a built in vibration reducer, designed to stop pulses from the power steering pump reaching the column. BYAJW195 Coupler- 3/4-36 x 3/4 DD 52.43 BYAJW200 Coupler- 1 DD x 3/4 DD 66.96 BYAJW675 Steel shaft 3/4 DD - 16 26.15 BYAJW680 Steel shaft 3/4 DD - 32 40.64 BYAJW530 Polished S/S shaft 3/4 DD 22 86.80 STEERING WHEEL ADAPTERS In most cases, a steering wheel adapter will be required to enable you to attach your steering wheel to your IDIDIT column. BYAJW040 3 bolt chrome... 118.93 BYAJW030 9 bolt polished- short... 158.57 BYAJW060 9 bolt polished inc IDIDIT button... 84.90 BYAJW055 9 bolt chrome inc IDIDIT button... 133.76 [part above is pictured] BY31120 9 bolt Billet Spec polished alum... 58.52 BYLC22400 9 bolt Mustang/Galaxy 67-76... 53.30 The above item will fit a std Ford stg column. HORN BUTTONS- B/SPEC BY32125 Large [covers screws] plain... 60.90 BY32325 Large bowtie... 69.44 BY32625 Large Billet Specialties... 58.52 BYRP2510Horn wire lead... 7.21 Steering Wheels- Billet Specialties These steering wheels use a 9 bolt adaptor. They have milled finger notches for an ultra comfortable grip. Many types available. BY30976 Anthem- 14... 201.26 BY30103 Street Lite 14... 241.61 BY30725 Classic 14... 291.98 BY30925 Banjo 14... 294.76 BY30973 Speedway 14... 209.46 BY30137 Split Spoke- 14... 243.30 Shown at right BY29003Gray leather 14 half wrap... 48.79 BY29005 Red leather 14 half wrap... 46.82 BY29008 Black leather 14 half wrap... 60.72 BY29002 Tan leather 14 half wrap... 45.60 BY29006 Burgundy leathr 14 half wrap 46.51 Leather half wrap is required for all above wheels Front Suspension Chevrolet/Pontiac Full Size Polyurethane front end control arm bushing set BY3-3108G 1955-64 Chevrolet... 79.06 BY3-3150G 1965-70 Chevrolet... 40.14 Lowers- reuse metal parts BY3-3103G 1971-73 Chevrolet + Bonneville... 81.80 Only models with 1-5/8 OD front lower bushes. Chevrolet Camaro/Pontiac Firebird & Trans am Polyurethane front end control arm bushing set BY3-3101G 1967-69... 87.40 BY3-3102G 1970-72... 66.84 BY3-3104G 1973-74 1-3/8 OD lowers... 75.19 BY3-3103G 1973-74 1-5/8 OD lowers... 81.80 Above part also fits 1973 Firebird BY3-3105G 1975-79... 83.32 Above part also fits 1974-79 Firebird BY3-3106G 1980-81... 89.00 BY3-3157G 1982-92 Lowers only... 44.21 BY3-3164G 1993-02 [Lowers re-use metal parts] 67.61

S12/4 S12/4 Front Suspension Chevrolet Corvette Polyurethane front end control arm bushing set These bushes will give added performance without creating any adverse changes to the original ride. BY3-3108G 1963-82... 79.06 BY3-3142G 1984-96... 91.45 Chrysler- RWD Polyurethane front end control arm bushing set BY5-3132G 1962-76 A body uppers only... 37.88 This number also fits B-Body 1965-72 uppers only & E-Body 70-74 Chrysler notes- A body- Dart, Demon, Duster, Valiant (Barracuda to 69) B body- Charger, Coronet, Satellite, GTX, Roadrunner, Superbee E body- (Barracuda 70 and up) & Challenger Chevrolet & Pontiac Polyurethane front end control arm bushing set BY3-3117G 1964-66... 83.32 Chevelle, Malibu, Monte-Carlo, Laguna, El-Camino, LeMans, GTO, Tempest. On 1966 Chevrolet models, there are two size rear lower bushes, these are 1.9 OD. BY3-3101G 1966-74- Bushes are round... 87.40 Chevelle, Malibu, Monte-Carlo, Laguna, El-Camino, LeMans, GTO, Tempest. On 1966 Chevrolet models, there are two size rear lower bushes, these are 1.65 OD. Nova & Chevy 2-1968-74. BY3-3172G 1967-72 Oval rear lower bushes... 65.15 Above number fits- Chevelle, Malibu, Monte-Carlo, Laguna, El-Camino, LeMans, GTO, Tempest. BY3-3160G 1962-67... 54.74 Above number fits- Nova, Chevy 2-1962-67. Ford Motor Company Polyurethane front end control arm bushing set. Must re-use existing outer metal shells. BY4-3101G 1960-66... 13.64 Falcon, Ranchero, Mercury Comet 1961-65, Mustang-lowers only BY4-3131G 1962-65 Fairlane... 17.60 BY4-3102G 1967-71 1-7/16 OD lower... 11.44 Fairlane, Grand Torino, Torino, Ranchero, Mercury Comet 1966-77, Mustang 67-73 1-7/16 OD lower BY4-3106G 1967-71 1-9/16 OD lower... 10.96 Fairlane, Grand Torino, Torino, Ranchero, Mercury Comet 1961-65, Mustang 1967-73 1-9/16 OD lower BY4-3130G 1974-78 Mustang... 58.76 BY4-3132G 1979-82 Mustang excl HD susp... 42.16 Above also fits Mustang 1983-93 BY4-3108G 1979-82 Mustang with HD susp... 30.64 BY4-3144G 1994-04 Mustang... 59.89 Front Strut Rod Bushes Polyurethane front strut rod bushes Ford Motor Company Polyurethane strut rod bushes Chevrolet BY4-7111G 1960-66... 25.97 Above number fits- Falcon, Ranchero, Fairlane 62-65, Mustang 64-66, Mercury Comet 1961-65 BY4-7112G 1967-71... 27.64 Above number fits- Fairlane, Grand Torino, Torino, Ranchero, Mustang 1967-73, Mercury Comet 1966-77, Cougar 1967-73 BY4-7117G 1972-79... 22.02 Above number fits- Fairlane, Grand Torino, Torino, Ranchero, Galaxie 1965-78, Thunderbird 1972-79, Cougar 1974-79 BY4-7113G 1974-78... 21.94 Above number fits- Mustang 1974-78 BY3-7109G 1965-70... 21.88 Above number fits- Belair, Biscayne, Caprice, Impala, Station Wagon BY3-7105G 1962-67... 19.37 Above number fits- Nova & Chevy 2 Polyurethane front strut rod bush set Chrysler- RWD BY5-7105G 1962-65... 12.31 Above number fits- A body 62-65. Front End Links- Anti-roll Bar Lengths- relate to straight shaft between bush platform washers Front Anti-Roll Bar Links Polyurethane bushed front end links for anti-roll bar BY9-8117G 2-5/8... 23.45 Above number fits- 1955-57 & 1971-90- Belair, Biscayne, Caprice, El Camino (thru 63), Impala, Station Wagon; Camaro/Firebird & Trans Am 1967-92; +73-77 Chevelle, Monte Carlo, Malibu & El Camino 64 up; Monza & Vega 1971-80; Nova & Chevy 2-1962-79; Mustang 67-73; Cougar 67-73; Pontiac LeMans, GTO, Tempest 73-77; Bonneville, Catalina (Grand Prix to 81 only), Safari Wagon 71-81; BY9-8118G 2-7/8... 20.05 Above number fits- Camaro/Firebird & Trans Am 1993-02; +1964-72- Chevelle, Monte Carlo, Malibu & El Camino 64 up; Chrysler B body 65-69; Chrysler A body 65-72; Fairlane, Grand Torino, Torino, (Ranchero after 15-3-72) 72-79; Galaxie 72-78; Thunderbird 72-79; Cougar 74-79; Pontiac Le Mans, GTO, Tempest 64-72; BY9-8119G 1958-64; 3-3/8... 20.05 Above number fits- Belair, Biscayne, Caprice, El Camino (thru 63), Impala, Station Wagon. Front Ant-Roll Bar Links Polyurethane bushed front end links for anti-roll bar BY9-8120G 1-5/8... 23.45 Above number fits- 1965-70- Belair, Biscayne, Caprice, El Camino (thru 63), Impala, Station Wagon, Corvette 63-82; Chrysler E body 70-74; Chrysler B body 70-72; Chrysler A body 1973-76; Fairlane, Grand Torino, Torino, Ranchero 67-71; Mustang 64-66; Comet 66-77; BY9-8121G 4-1/2... 19.91 Above number fits- Mustang 79-93; BY9-8124G 3-9/16... 20.05 Above number fits- Mustang 94-04; BY3-8102G 1984-87;... 12.56 Above number fits Corvette BY3-8103G 1988-96;... 12.56 Above number fits Corvette

S12/5 S12/5 Anti-Roll Bar Bushes Front Suspension Anti-Roll Bar Bush Sets-with Brackets Polyurethane Anti-Roll Bar Bush sets. Brackets are 4-1/2 long, by 1-3/8 wide, 1-3/4 high, 3/4 from centreline of hole for bar, to mounting face of bracket. Mounting bolts centre to centre can be between 3-5/8 and 2-9/16 [holes are slots]. BY9-5106G 3/4-19mm... 21.48 set BY9-5108G 7/8-22mm... 22.76 set BY9-5109G 15/16-24mm... 18.37 set BY9-5110G 1-25mm... 22.76 set BY9-5112G 1-1/8-28.5mm... 21.48 set BY9-5113G 1-1/4-31.5mm... 21.49 set BY9-5114G 1-5/16-33mm... 19.16 set Chevrolet Camaro-Nova & Chevy 2 Polyurethane front anti-roll bar bushes BY3-5202G 11/16 Bar... 25.92 BY3-5203G 13/16 Bar... 22.94 Above numbers fit- Camaro 67-69; Nova & Chevy 2 68-74 HEIDTS FRONT SUSPENSION Heidts were one of the first companies to make alternative crossmember based suspension assemblies, based on the 1974-78 Mustang II front suspension. Up until a few years ago, the Mustang II could be readily found in scrapyards, and it was a simple matter to remove the front suspension, and modify it to suit ones Hotrod. Nowadays, these cars are getting a bit thin on the ground. This is where Heidts comes in [23 years in business], manufacturing cross members to fit many classic cars & trucks. If you have the suspension parts from a Mustang II, then these will fit the crossmember. Otherwise, you can buy all new components, with many different options. The Heidts front suspension design, follows faithfully, the design used by Ford Motor Company. This is because it is technically a very good design. Ford got it right first time with this design, eliminating bumpsteer, and including built-in anti-dive into the design. Some of the other Mustang II based designs do not have these features. Hotrods & Custom/Street cars built these days, need to be safe, as more & more families have become involved, giving us a much greater responsibility. The car needs to handle and brake in safety, from speed. It is no good anymore having a car that will do 200mph in a straight line, but has poor brakes & suspension. Tailgating the family in a 2004 Mondeo on the M1 at 80mph, in your 1500bhp twin turbo 34 Ford coupe, is not a good idea, unless you have brakes the equal of his. The Heidts front suspension cross-member is made in the USA, not China, and it is beautifully made, a work of art. I visited the Heidts factory, just north of Chicago, and was very impressed with the high quality of their work. I look forward to fitting one of these kits to my own car in the future. FRONT SUSPENSION CROSSMEMBERS BYPX-101-E Ford 1933-34 Car... 409.24 Upper fender adapter brackets included. radiator tabs included. Must use-manual steering rack & narrowed suspension arms BYPX-102-E Ford 1935-40 Car & 35-41 Pickup 401.63 Boxing plates included. Narrowed suspension arms recommended. Weld on engine mount brackets are avail- Ford V8 BYAJW335 & Chevy BYAJW450 BYPX-103-E Ford 1941-48 Car... 381.82 FRONT SUSPENSION CROSSMEMBERS BYPX-105-E Ford 1953-56 F-100 Pickup... 425.66 Steering rack extensions required BYPX-104-E Ford 1948-52 F-1 Pickup... 401.63 Steering rack extensions required

S12/6 S12/6 Front Suspension FRONT SUSPENSION CROSSMEMBERS BYCX-103-E Chevy 1940-48 Car... 391.31 FRONT SUSPENSION CROSSMEMBERS BYCX-308-E Chevy 1955-59 Pickup... 415.02 BYCX-104-E Chevy 1949-54 Car... 426.12 BYCX-305-E Chevy 1937-39 Pickup... 391.31 C notched plates included BYCX-306-E Chevy 1940-46 Pickup... 415.02 C notched plates included. Steering rack extensions required. BYKX-101-E Universal 56-1/2 track width... 415.02 56-1/2 track width crossmembers fit 24-30 frame rails.[outside to outside]. The crossmember & spring towers are made oversize to allow trimming & fitting to your chassis. Templates & instructions, designed for a home builder to install. BYPX-320-E Mustang 1964-70+ 67-70 Cougar 386.77 Includes boxing plates that weld in place. 2 dropped spindles recommended for std ride height. Use a manual steering rack & rear sump. 351C will not fit. Weld on engine mount brackets are available-ford V8 BYAJW335 & Chevy V8 BYAJW450 UNIVERSAL C notched plates included BYCX-307-E Chevy 1947-54 Pickup... 401.63 NOTE: Some 54 s were sold in 55 be sure of your model! C notched plates included WHAT ELSE DO I NEED? SUSPENSION ARM KIT, BRAKE SYSTEM KIT, STEERING RACK & MOUNT KIT, SPRINGS, SHOCKS and RUBBER SEATS, SPINDLE/FRONT UPRIGHT KIT, BRAKE HOSE KIT, STEERING COLUMN CONNECTION PARTS [see S12/3], ANTI-ROLL BAR [option] -most kits are pairs & include required hardware, everything is unpainted- TUBULAR SUSPENSION ARM KITS [unpainted] choose arms tubes & gussets! BYAJW545 Std arm kit... 761.08 BYAJW560 Coil-over shock arm kit... 671.04 Coil over shocks make it easier to adjust the vehicle height [front] BYAJW580 Narrowed std arm kit [some Fords] 747.04 BYAJW635 Narrowed coil-over shock arm kit 687.59 BYAJW550 Air-bag arm kit... 859.96 The above kit requires the Air-Bag installation pack BYAJW810 BYAJW820 Spacer tubes for crossmember-2req 23.38ea BYAJW670 Gussets for crossmember-2req... 3.90ea The above two line items need to be welded into the c/member [2 ofeach] BYAJW275 Replacement bushes upper arms... 14.78ea BYAJW280 Replacement bushes lower arms... 14.78ea BYAJW285 Replacement ball joints... 25.87ea STEERING RACK KITS- choose rack & mounts! DISC BRAKE KITS [unpainted] choose one! BYAJW655 11 brake kit Chevy bolt circle... 424.13 BYAJW685 11 brake kit Ford bolt circle... 424.13 Chevy bolt cicle = 5 on 4-3/4, Ford bolt circle = 5 on 4-1/2 BYAJW690 11 Chev-Willwood blk callipers.. 800.23 BYAJW695 11 Ford- Willwood blk callipers.. 787.88 Callipers are lighter [aluminium]. They are the 4 piston version SPRINGS & SHOCKABSORBERS choose shocks, springs & rubber seats! BYAJW020 Standard shockabsorber... 75.31 pr BYAJW850 Billet aluminium coil over shock.. 564.20pr The above shock has 10 position adjustable [rebound] damping BYAJW305 Rubber seat for shock [required]... 22.67pr BYAJW710 Manual rack LHD- 26 x 9/16... 234.14 Mounts included. Use universal joint BYAJW750 with above rack BYAJW106 Power LHD-Mustang II 36x3/4.. 524.15 Uses BYAJW495 universal. Complete with mounting kit. NEW! BY8026070 Fittings for rack to attach hoses... 36.28 BYAJW1015 Poly bushes rack mounting... 27.07 set Above kits must be used for POWER steering racks. SPINDLE [FRONT UPRIGHT] KITS choose one! BYAJW700 Std height Mustang II... 231.34 BYAJW705 2 drop Mustang II forged... 251.99 On a Mustang, the 2 drop spindles are needed for std ride height BYAJW215 Black 300lb spring for std shock... 98.39pr BYAJW295 Black 350lb spring for std shock.. 107.64pr Black springs fit between upper & lower arms with std shock through centre. No ride height adjustment, apart from correct pressure spring and 3/4 spacers available under part number BYAJW825 to raise ride height of vehicle. BYAJW825 Spring spacers-3/4... 40.09pr If your vehicle is riding a bit low in the front, these spacers will lift the Heidts springs up around 3/4. BYAJW805 Chrome 500lb spring-coil overs... 153.24pr BYAJW485 Chrome 600lb spring-coil overs... 156.88pr BYAJW290 Chrome 700lb spring-coil overs... 156.88pr These springs mount on an adjustable platform on the shockabsorber. This gives ride height adjustment. A spanner to adjust the spring height is available under part number BY62030. BYAJW887 Flat bearing for coil overs... 53.03 pr The above bearing makes adjusting the ride height much easier. See also next page-

S12/7 S12/7 Front Suspension BRAKE HOSE KITS choose one! BYAJW590 Std Heidts brake kits... 61.06 Use with BYAJW655/685 BYAJW740 Heidts brake kits w/willwood 14.. 45.07 Use with BYAJW690/695 BYAJW745 For Willwood callipers 16 hose... 48.10 BYAJW540 Weld on tab kit for brake hose... 24.02 AIR BAG INSTALLATION PACK Picture shows more parts than in kit HEIDTS FRONT ANTI ROLL BARS option! These anti-roll bar kits come complete with all parts required to fit. Assists in keeping your car/truck sitting flat through the corners. If marked with * then only works with Heidts Must II, front end kit. BYAJW435 1955-57 Chevy 1 diam+urethane 239.05 BYAJW660* 1948-54 Ford P/up +53-56 F100. 231.34 BYAJW525 1940-46 Chevy Pickup... 197.84 BYAJW665* 1947-54 Chevy Pickup... 242.59 BYAJW310* 1964-70 Mustang+1967-70 Cougar 255.54 BYAJW810 Heidts Air-Bag kit for BYAJW550 654.85 Use with BYAJW550 to finish air-bag type front end MUSTANG CHASSIS STIFFENER 1964-70 This is another item that gives the unibody design added stiffness for performance use. Use with Heidts subframe connectors. BYAJW345 Chassis stiffener 64-70... 342.19 55-57 Chevy Steel Front Spindles 2 Drop These front spindles are forged & are made from 1045 heat treated alloy steel. With the stub-axle repositioned to give a 2 drop, your suspension angles remain as standard. Includes calliper brackets. MUSTANG 1964-70 Inner Wing Panels Use when fitting the Heidts front subframe kit. Remove the old panels, and replace with these. BYAJW315 Inner wing panel 64-66 Mustang... 66.17 BYAJW320 Inner wing panel 67-70 Mustang... 74.65 67-69 CamaroForged Front Spindles 2 Drop These front spindles are forged & are made from 1045 heat treated alloy steel. With the stub-axle repositioned to give a 2 drop, your suspension angles remain as standard. BYAJW410 2 drop spindles Chevy 55-6-7... 380.56 1 Dropped Coil Springs Chevy 55-6-7 To give your shoebox an even lower look, add these Heidt 1 dropped coil springs. Combined with the 2 dropped spindles, they will put your cruiser a full 3 in the weeds safely & easily. BYAJW430 1 lower spring Chevy 55-6-7... 87.16 BYAJW390 2 drop spindles Camaro 67-69... 307.27 AirRide Air-Spring Conversion Kit If you already have a Mustang II based front suspension, this kit will enable you to fit the AirRide type of air springs. Of course you will need many other parts as well, including a compressor kit. BYAJW465 AirRide conv kit [Must II]... 118.01

S12/8 S12/8 Steering & Brakes STEERING Heidt Adjustable Power Steering Valve Tune your power steering, with the Heidt patented adjustable power steering valve. If you are using a high-flow pump with a steering rack, you can adjust the feel using this valve. BYAJW455 Adjustable power steering valve... 112.46 Extension Kits 4 -Steering Rack These extensions are required on SOME Heidt front crossmember kits. Look at crossmember information to find out. BYAJW470 4 extensions manual Heidt rack... 66.41 BYAJW475 4 extensions power Heidt rack... 77.11 PWR RACK CONVERSION KIT 1955-57 CHEVY This is a bolt on kit, but the pump, pump brackets, pulleys, belts & hoses are all extra, depending on engine being used. Claimed to have no bump steer. POWER STEERING PUMP HOSE KITS BYAJW575 Power steering pipe kit... 262.08 Kit of parts to help you connect the Heidts power steering rack, Heidts adjustable valve, & the GM integral tank, power steering pump- BYP304. BYAJW1040 Power steering pipe kit... 156.91 Use the kit BYAJW1040 with the pumps- BYAJW965, BYAJW925 BYAJW1010 Power steering pipe kit... 146.87 Use the kit BYAJW1010 with the pumps- BYAJW845, BYAJW970 BYAJW960 1955-57 rack conversion 597.78 POWER STEERING PUMPS We stock two types of pump. The GM pump with a keyed shaft & reservoir attached and the Maval pump with plastic tank. Racks are generally low volume, steering boxes mainly high volume. BYAJW965 GM lo-flo black- keyed... 191.00 BYAJW925 GM lo-flo chrome-keyed.. 265.62 BYP304 GM hi-flo chrome- keyed.. 228.55 BYAJW845 Pump & tank lo-flo... 224.03 BY8020630 Pulley for BYAJW845... 82.22 BYAJW970 Pump kit SBC lwp lo-flo... 339.91 The above pump kit is lo-flo & comes with brackets BYAJW975 Steel brackets SBC lwp... 68.52 BYAJW980 Steel brack Pont 400... 68.52 BYAJW985 Steel brack Ford 289... 45.04 Steel brackets are for BYAJW845 pump only BRAKES MUSTANG FRONT 11 DISC BRAKE KITS 1964-70 For Mustang V8-5 stud wheel cars that originally had drum brakes from Ford. Complete with dual master cylinder & 7.5 or 9 dual diaphragm power brake booster/servo. Callipers are single piston. Versions for Automatic and manual transmission. [Must have left the factory like this]. Picture shows an AJW905 kit, for one wheel. Kits contain all the parts needed for two wheels.[1 car] BYAJW905 V8 1964-66 manual... 952.09 BYAJW910 V8 1964-66 auto... 893.00 BYAJW912 V8 1967-70 auto & man.. 952.09 Front 11 Disc Brake Kit 55-57 Chevy Use this kit where the vehicle has Heidts 2 dropped front uprights or spindles. Front 11 Disc Brake Kit 55-57 Chevy Use this kit where the vehicle still has the O.E. or original front uprights or spindles. BYAJW425 Disc brake kit 55-57 Chevy 388.93 BYAJW420 Disc brake kit for 2 drop 324.23

S12/9 S12/9 Brakes FORD 8 REAR DISC BRAKE KIT V8 Use for 8 rear axle with small bearing. Five stud fixing with solid 10-1/2 discs. Complete with callipers & hardware. BYAJW925 Rear disc kit Ford 8... 370.78 MUSTANG 1964-66 MASTER CYLINDER/SERVO This is a complete dual master cylinder together with a 7.5 dual diaphragm brake servo or booster. Will work with OEM drum/drum or aftermarket disc/drum. Only works on a car that left the factory with an automatic transmission, & non power brakes. OK with V8 or 6cyl. BYAJW915 1964-66 m/cyl & servo-... 329.82 MUSTANG 1967-70 MASTER CYLINDER/SERVO This is a complete dual master cylinder together with a 7.5 dual diaphragm brake servo or booster. Will work with OEM drum/drum or aftermarket disc/drum. Will work on a car that left the factory with either a manual or automatic transmission, & non power brakes. OK with V8 or 6cyl. BYAJW920 1967-70 m/cyl & servo... 329.82 CHEVY 1955-6-7 DUAL M/CYL & SERVO This is a complete dual master cylinder together with a brake servo or booster, for disc/drum setups. These kits come complete with a piped up proportioning valve, to reduce pressure to the rear brakes. BYAJW415 Dual m/cyl & servo 55-57 380.84 1953-56 FORD PICKUP-CHASSIS MOUNT -dual m/cyl & servo- Dual master cylinder & 8 servo, chassis mounted. Includes mounting bracket & remote reservoir. Set up for disc /drum. Proportioning valve incl. BYAJW940 Dual m/cyl & servo... 432.11 ELECTRO-BOOST M/CYLINDER- 1900psi! Modern hot-rods/custom cars/resto-mod classics, often have large very powerful engines with little or no vacuum available for a brake servo. In some cases there is no room for a brake servo either. Add to that a 4 wheel disc system and you have the need for an alternative to a servo with more pressure available for your brake system. This electric high power master-cylinder uses an electric pump with an accumulator, just like many OEM vehicles today. If the electrical system or the pump should fail, then the accumulator holds a reserve of pressure to give approx 10 power assisted stops, before the system goes back to non-power assist.uses Dot 5 fluid. Do not mix fluid types. This system gives a very good pedal and very powerful brakes that will stop you on a sixpence! MUSTANG 1964-66 MASTER CYLINDER/SERVO This is a complete dual master cylinder together with a 9 dual diaphragm brake servo or booster & proportioning valve. Will work with OEM drum/drum ** or aftermarket disc/drum. Only works on a car that left the factory with a manual transmission, non power, drum/drum brakes. OK with V8 or 6cyl. ** If it is a drum/drum car, the proportioning valve must be removed. BYAJW1030 1964-66 m/cyl & servo- 364.73 MUSTANG 1967-70 MASTER CYLINDER/SERVO This is a complete dual master cylinder together with a 7.5 brake servo or booster, for OEM factory fitted power brake, disc/drum setups,only. Works with manual or automatic transmission. OK with V8 or 6cyl. BYAJW935 1967-70 m/cyl & servo... 364.73 CAMARO DUAL M/CYL & SERVO This is a complete dual master cylinder together with a brake servo or booster, for disc/drum setups. These kits come complete with a proportioning valve. BYAJW400 Dual m/cyl & servo 67-69... 338.52 BYAJW490 Dual m/cyl & 7 servo 70-81... 340.80 BYAJW730 Dual m/cyl & 9 servo 70-81... 347.62 1947-54 CHEVY PICKUP-CHASSIS MOUNT -dual m/cyl & servo- Dual master cylinder & 8 Bendix style servo, chassis mounted. Set up for disc /drum. Includes mounting brackets. Proportioning valve included. BYAJW945 Dual m/cyl & servo... 476.05 Adjustable Brake Proportioning Valve An adjustable brake proportioning valve is used to balance front and rear brake pressures, especially in disc/drum combinations. BYAJW950 Electro-boost kit-mustang 1292.44 Rear Brake residual Pressure Valve Used to maintain pressure in rear drum brake pipes/hoses. BYAJW445 Adj brake proportioning valve... 54.62 FORD PROPORTIONING VALVE This is a 70 s style valve that could attach to the inner wing. It is set up for a disc/drum system. BYAJW570 10 lb residual pressure valve... 30.84 BYAJW955 Ford proportioning valve... 58.60

S12/10 S12/10 Rear Suspension Original Type Rear Suspension Polyurethane rear leaf spring bushing set Chevrolet Leaf Spring Bushes BY3-2118G 1955 Chevrolet... 28.27 BY3-2119G 1956-57 Chevrolet... 37.81 BY3-2101G 1968-74 Nova/ChevyII mono leaf 53.65 BY3-2103G 1968-79 Nova/ChevyII multi leaf. 58.90 Polyurethane rear control arm bushes Chevrolet Camaro/Pontiac Firebird Rear Suspension Polyurethane rear leaf spring bushing set Chevrolet & Pontiac Saloon BY3-3133G 1964 Uppers reuse outer metal shells 78.66 1964Chevelle, Monte Carlo,Malibu, Lemans, GTO & El Camino 1964on BY3-3132G 1965-81 control arm bushes... 91.08 Chevelle, Monte Carlo, Malibu, Lemans, GTO, Tempest & El Camino BY3-2101G 1967-69 Camaro-Firebird Mono-leaf 56.09 BY3-2102G 1967-69 Camaro-Firebird Multi-leaf 51.42 BY3-2103G 1970-81 Camaro-Firebird... 73.31 Chevrolet Corvette Rear Suspension Polyurethane rear leaf spring bushing set BY3-2121G 1954-62 rear leaf spring bushes... 23.45 Polyurethane rear control arm bush set BY3-3191G 1963-82 rear control arm bushes... 34.88 BY3-3145G 1984-95 rear control arm bushes... 45.53 Polyurethane rear leaf spring spring cushions BY3-2104G 1963-82 spring cushions... 16.88 BY3-2123G 1984-96 spring cushions... 14.82 Polyurethane rear strut rod bushes BY3-7101G 1963-74 1-1/2 OD rod eye... 39.50 BY3-7102G 1975-82 1-3/4 OD rod eye... 38.48 Polyurethane diff pinion mount & carrier bush set BY3-1101G 1963-82 pinion mount set... 11.02 BY3-1104G 1980-82 diff carrier bush set... 24.55 BY3-1103G 1984-96 diff carrier bush set... 25.79 Polyurethane leaf spring pads BY3-6112G 1967-69+62-79 Nova/ChevyII multi 22.92 Above item also fits 62-79 Nova & Chevy II+Firebird 68-69 Multi BY3-6111G 1970-81 multi leaf... 34.48 Polyurethane rear control arm bushes BY3-3136G 1982-02 Rear control arm bushes.. 57.59 Polyurethane Torque Arm mount bushes BY3-1111G 1984-92 & 1993-02 Torque arm bush 17.24 Lips facing away from driveshaft-see Energy catalogue drawing Polyurethane rear control arm bushes BY3-7106G 1982-01[02-Pont]panhard bar bushes 17.16 Ford Fairlane & Mustang Rear Suspension Polyurethane rear leaf spring bushing set BY4-2141G 1962-65 Fairlane... 52.60 BY4-2123G 1964-65 Must-9/16 shackle blts... 52.48 BY4-2101G 1966-73 Must-1/2 shackle blts... 61.69 Polyurethane rear control arm bushing set BY4-3114G 1979-93 Mustang round bushes... 76.62 C.E. LADDER BAR CROSSMEMBER KIT Designed to provide a sturdy mounting point for the ladder bar front rod-end. Capable of withstanding the abuse of a racing suspension while adding strength to the chassis. The 54 wide bar also acts as a rear prop-shaft loop. Includes brackets & bolts. Welding required. BY2019 Ladder bar crossmember... 84.61 Chrysler A & B Body Leaf Spring Bushes Polyurethane rear leaf spring bushing set Chrysler notes- A body- Dart, Demon, Duster, Valiant (Barracuda to 69) B body- Charger, Coronet, Satellite, GTX, Roadrunner, Superbee E body- (Barracuda 70 and up) & Challenger BY5-2105G 1962-76 A body... 48.10 BY5-2106G As above but with-2 eye & 5/8 bolt 48.74 BY5-2101G 1965-72 B w/2 eye excl 426/440 48.10 BY5-2104G 1965-72 B w/1/2 eye 426+440. 50.09 Mustang/Camaro HD Shackle Kit Polyurethane bushed HD rear shackle bushes & hardware kit BY4-2136G 1964-73 Mustang... 84.70 BY3-2135G 1967-81 Camaro... 88.14 CE LADDER LINK [BARS] Allows the racer to fine tune the suspension without removing the bar from the car. Pivoting lower adjusters eliminate the bind found in some bars. 1 x.156 DOM tube. Forged solid rear rod ends. 33.5 overall. High quality alloy spherical front rod ends. Black powder coated. Welding required. BY2005 Ladder link kit inc ends... 327.73 CE LADDER BAR SAFETY KIT Captures the front mounting bolt of the ladder bar in the event of a rod end failure. Kit includes the upper & lower weld in brackets, retaining straps & hardware for two ladder bars. BY2018 Ladder bar safety kit... 27.71 CE FOUR LINK KIT CE DIAGONAL LINK Offers enhanced adjustability over a ladder bar suspension for increased performance. By locating the bars with the various mounting holes in the brackets, you can create an instant centre that is correct for your application. 17-1/4 long, 1 diam x.156 direct threaded links. 3/16 thick mounting brackets. Includes 8 chrome-moly rod ends. Complete with harware. Requires welding. BY2017 Rear four link kit... 304.60 BY2052 Bolt on diagonal link 36.5... 97.49 Eliminates side to side housing movement. Superior to the Panhard bar for eliminating sway in ladder bar & four link suspensions. This bolt on diagonal link can be used with the CE Ladder Bars, Ladder Links & Std 4-links with 3/4 mounting holes. Made from 3/4 x.156 mild steel tube. Kit includes rod ends & mounting hardware.

S12/11 S12/11 -Rear Suspension- CE PANHARD BAR KIT Eliminates side to side rear axle housing movement within the chassis. Keeps your tyres from rubbing the wheel openings, making sure you get down the track in a straight line. Perfect for street driven vehicles. 30 tube can be trimmed to fit. Includes gusseted mounting brackets & rod ends. Hardware & instructions included. Welding required. BY2037M Panhard bar kit... 130.06 CE BOLT-ON PROP-SHAFT SAFETY LOOP Contains the propshaft and prevents flipping the vehicle in the event of a front u/j failure. Manufactured from CNC formed 1/4 thick, 2 wide mild steel. Mounts to the floorpan with four bolts per side. Zinc plated. BY3028 Safety loop... 57.34 CE UPPER COIL-OVER SHOCK MOUNT KIT Designed to mount between the rear frame rails Street Rod, Pro-Street, Drag Race application. Includes one 40 long x 1.625 mounting tube,.188 thick mounting brackets, 4 shock mount tabs, 4 shock spacers for older style coil-over shocks and all mounting hardware. Welding required. BY2046 Upper coil-over mount kit... 54.16 CE ROD ENDS- 3/4 HOLE Static radial load capacity- low carbon steel- 14,290lbs. chrome moly steel- 28,090lbs. BY6011 Low carbon steel 3/4 RHT... 22.73ea BY6012 Low carbon steel 3/4 LHT... 22.73ea BY6130 Chrome moly steel 3/4 RHT... 26.58ea BY6131 Chrome moly steel 3/4 LHT... 26.58ea CE LOWER COIL-OVER SHOCK MOUNT KIT Provides a solid adjustable mounting point for coil over shockabsorbers. Fits housings with 3 OD axle tubes. Has 6 of height adjustment in 1/2 increments. 1/4 thick housing brackets, 3/16 thick shock brackets. Includes hardware & spacers. Welding required. Kit is for qty 2. BY2047 Lower coil-over mount kit-pr... 81.76pr CE PROFESSIONAL WHEEL-E BARS Wheelstands may look spectacular but they can actually hurt performance. Although some front end lift is beneficial for weight transfer, excessive lift can slow forward motion. When a car wheelstands upon initial launch, it uses up power that could propel the vehicle forward. This results in slower ET s. Wheel-E-bars are designed to limit & control big wheelstands without unloading the rear tyres. As the rear housing rotates, the natural rubber wheels come in contact with the track. The shock of this contact is absorbed by both the lower aluminium struts & the coil spring upper struts which keep the tyres from unloading. As the housing continues to rotate more & the front end begins to lift, the coil springs on the upper struts start to compress. The more that the springs are compressed, the more force they exert against the housing rotation, eventually overcoming the rising force of the front end and gently pushing it back down. This converts the rotational energy into forward motion, resulting in quicker ET s. Overall length is 44 & the centre to centre mounting bracket distance is 22-11/16. BY2016 Chrome wheel-e-bars... 410.94 HEIDTS REAR SUSPENSION HEIDTS 4 BAR- CHEVY CLASSIC TRUCK Replaces old leaf springs. Gives a much better ride, & better cornering. Will need Panhard rod, coil overs & coil springs. 1/2 ton only! BYAJW755 Chevy p/up 1947-53 weld in... 678.68 Above kit is for 1/2 ton, will not fit 3/4 ton BYAJW760 1954-55 1st series-weld in... 793.62 BYAJW765 1955-59 2nd series-weld in... 793.62 PANHARD ROD FOR HEIDTS 4 BAR Required for Heidts 4 bar for Classic Truck. Weld on. HEIDTS 4 BAR- FORD CLASSIC TRUCK Replaces old leaf springs. Gives a much better ride, & better cornering. Will need Panhard rod, coil overs & coil springs BYAJW775 Ford p/up 1953-56 F100 weld in.. 609.66 REAR COIL OVERS HEIDTS CLASSIC TRUCK 4 BAR BYAJW780 Weld on-except 47-54 Chevy... 127.84 BYAJW785 Weld on- 1947-54 Chevy only... 125.32 HEIDTS REAR COIL 4 BAR SPRINGS For use with Heidts 4 bar rear for Classic Truck BYAJW790 Black- non adj damping... 285.85 REAR ANTI-ROLL BAR KITS BYAJW795 11 black rear coil springs 250lb.. 127.88 BYAJW800 11 black rear coil springs 300lb.. 123.83 HEIDTS REAR 4 BAR KITS This is a bolt on kit [apart from the rear axle case brackets] complete with coil overs and springs. Does not include axle housing. BYAJW340 Mustang 1964-70... 1767.48 BYAJW375 67-69 Cam/F-bird+Nova 68-72.. 1170.82 BYAJW440 Chevy 55-57 std suspension only. 224.92 Above kit has a 7/8 diameter bar with Urethane bushes Subframe Connectors Mustang-Coupe 1964-70 Bolt on subframe connectors help eliminate bending, flexing & cracking of spot-welded sheet metal panels. They also tie the front & rear frames together creating a solid platform for increased performance levels. For use with Heidts rear 4 bar kit. BYAJW350 Subframe connectors 64-70... 269.89

S12/12 S12/12 Subframe Connectors Camaro 67-69 Coupe -Rear Suspension/Air-Ride- For use with the Pro-G front subframe kit. Bolt on subframe connectors help eliminate bending, flexing & cracking of spot-welded sheet metal panels. They also tie the front & rear frames together creating a solid platform for increased performance levels. BYAJW380 S/frame connectors Camaro Pro-G... 162.89 AIR-RIDE REAR SUSPENSION AIR4LINK REAR 4 BAR KITS Here are some advantages of the rear Air4Link. Superior ride quality, Rubber bushes eliminate poly bushing squeak & improve ride quality, Allows maximum suspension travel & tighter wheel to inner wing clearances, Highly adaptable to most vehicles, Simple, straightforward installation,.219 wall direct threaded DOM tubing for maximum strength,.188 wall alloy steel brackets are CNC lasercut & folded for strength & accuracy. As to which version you should use, this boils down to how much space is available. The triangulated version is more suitable is you have very little clearance around the tyre. Welding & basic fabrication skills are needed. Rear springs are extra. BY18987999 Triangulated 4 bar kit... 483.68 BY19998801 Parallel 4 bar kit with panhard rod 591.18 AIRBAR BOLT-IN 4 LINK 1955-57 CHEVY This 4 bar unit is designed for the Tri-Chevy. It is complete with upper and lower mounts for Shockwaves. there are two types of chassis used- one piece section & 2 piece section. We can make up either type. BY11027199 For one piece chassis... 1280.88 BY11037199 For 2 piece chassis... 1280.88 BY90000557 C/member for 2 piece... 349.78 UNIVERSAL REAR SHOCKWAVES [PAIRS] Here is some information on the Black, non adjustable, shockwave. The ride height of the Shockwave is much more important than the air pressure it runs at. Every Shockwave has an optimal ride height. The further you deviate from this intended ride height, the more ride quality & handling performance will suffer. If run too low, the Shockwave and/or suspension may bottom out. If run too high, the excessive air-pressure will create a stiff ride, and you may top out the Shockwave. In general a longer Shockwave will give more suspension travel. this will give better ride quality because the vehicle has more distance to absorb road bumps. The heavier the vehicle, the more important this becomes. Sold in pairs. BY20250702 4 up to 780lb 5 stroke... 450.00 Compressed: 11.56 // Ride Height: 14.5 // Extended: 16.56 BY20240802 5 up to 1200lb 4.1 stroke... 450.00 Compressed: 10.66 // Ride Height: 13 // Extended: 14.76 BY24050801 5 up to 1200lb 5.2 stroke... 701.90 Compressed: 11.85 // Ride Height: 14.6 // Extended: 16.42 REAR UPPER-CROSSMEMBER-SHOCKWAVE Includes axle mounts & weld in upper Shockwave crossmember. Does not include Shockwaves. BY11009099 Upper crossmember mount 155.64 REAR SHOCKWAVE BRACKET/MOUNT Brackets/mounts for Shockwave. BY90000034 Shock bracket-rear upper.. 17.38 BY90001928 4 link mount-lwr rear w/bolts 80.62 AIR-RIDE TANKS/PUMPS etc MANUAL AIR-RIDE SYSTEM The original RidePro system utilizes a quality solenoid air valve system & dependable electric components to provide simple, & reliable control. Control panel provides simple & accurate inflate / deflate control for each airspring. Vehicles up to 3500lbs. Rise time 3-5 seconds. 327 Thomas compressor, ARV4000 airvalve, 1/4 airline & fittings, electronic control. BY30154000 Manual system- 3 gallon tank... 1037.53 RidePROe3 AIR-RIDE SYSTEM The RidePROe3 system provides automatic adjustment with the use of an ECU & digital display. Rise time 3-5 seconds. [BY30334100 3 seconds]. 2-327 Thomas compressors, ARV4000 airvalve, 1/4 airline & fittings, electronic control. Relies solely on air pressure sensors for each spring, to adjust the ride height. Three presets. LevelPRO height sensors available also. BY30334000 RideproE3 >3500lb- 3 gallon tank 1612.28 BY30334100 RideproE3 >4500lb- 5 gallon tank 1827.25

S12/13 S12/13 -Air-Suspension Control-Tanks/Pumps etc- Air-Ride Front Suspension-Rear Axle- RidePROe3 REMOTE CONTROL AIR-LINE CUTTER Remote control option with two key fobs. BY31008500 E3 remote kit... 160.08 BY90001081 Tubing cutter- get those square ends 13.08 HEIGHT SENSOR KIT 4-PACK Adding LevelPro sensors to your RideProe3 system greatly enhances the system s ability to automatically level in a wider range of circumstances. If you are looking for the ultimate in accurate, leveling suspension, this is the way to go. Includes wiring. BY30400034 Height sensor pack... 351.08 AIR-RIDE FRONT SUSPENSION 1955-57 FRONT SHOCKWAVES These units bolt right in to the standard suspension arms. BY11012409 Fr/Shockwaves Tri-Chevy 599.62pr REAR AXLE Diff Carrier Gasket BYP27944 GM 12 bolt 4.07 BYP27807 8 Ford 4.14 BYP27929 9" Ford 4.99 ARP Ring Gear Bolt Kit For Ford 9", 7/16" x 0.940". Special hardened, precision ground washers are included. 200,000 PSI. BY250-3002 Ring gear bolt kit... 33.91 kit FORD- 9" CROWNWHEEL & PINION 10 Bolt - 9.00" dia. ring gear, 1.313" dia. pinion stem. Installation Kits Motive Gear installation kits provide most of the parts required for a crownwheel & pinion change. Kit contents vary. Ask salesperson for exact contents of the kit you require. BYF9-350* Ratio: 3.50 Teeth: 35-10... 219.65 BYF9-370* Ratio: 3.70 Teeth: 37-10... 219.65 BYF9-389* Ratio: 3.89 Teeth: 35-9... 219.65 BYF9-411* Ratio: 4.11 Teeth: 37-9... 219.65 * 8620 Steel, Street gears BYR9RMK Ford 9"... 114.11 kit

- SHOCKABSORBERS - S12/14 HD Shocks for std OEM Cars S12/14 SHOCKABSORBERS These shockabsorbers [RQ] have been designed & tuned for optimum ride quality in Street Rods, Muscle Cars, Classic Trucks & Cruisers. It s the perfect solution for the hotrodder who wants to install it & forget it. they are designed to replace the OEM shockabsorbers & the vehicle must have the stock suspension & ride height. These shockabsorbers are made in Indiana in the USA, not Mexico or China. They are an impact forged, aluminium monotube design. Here are some features- Mono-tube design allows a large piston for superior oil control- increases ride quality & handling performance. It also uses less components than a twin-tube design for superior fluid control. The Teflon piston wiper allows consistent piston/bore contact & repeatable performance. There is a specially contoured composite gas separator cup which optimizes dead length & ensures proper nitrogen/oil separation. Externally, the body is hard coat anodized for years of lasting beauty & performance. There is an integral internal bumpstop which eliminates extension crashing. The main piston rod is a 1/2 hardened shaft precision ground & straightened to a tolerance of.001 for increased durability & performance. A billet end cap with integrated debris wiper helps to prevent seal damage. The oversized rod guide improves piston rod stability. FRONT SHOCKABSORBERS BY22059846 1956-60 Cadillac... 126.28ea 1970-81 Camaro... 1963-82 Corvette 1955-57 Chevy... 1965-70 Impala 1982-96 Impala... 1960-70 Galaxie 1972-76 Torino FRONT SHOCKABSORBERS REAR SHOCKABSORBERS BY22049846 1967-69 Camaro... 126.28ea 1984-87 Corvette... 1989-96 Corvette 1968-79 Nova... 1968-72 Chevelle 1978-88 Malibu G-body FRONT SHOCKABSORBERS BY22089842 1967-69 Camaro... 126.28ea BY22099847 1970-81 Camaro... 126.28ea REAR SHOCKABSORBERS BY22049850 1953-62 Corvette... 126.28ea 1955-56 Fairlane FRONT SHOCKABSORBERS BY22079850 1964-70 Mustang... 131.72ea 1957-58 Fairlane... 1966-70 Fairlane 1968-71 Torino... 1960-70 Falcon REAR SHOCKABSORBERS BY22069846 1988 Corvette... 131.72ea 1958-64 Impala... 1964-67 Chevelle 1957-58 Fairlane... 1987-96 Dodge Dakota FRONT SHOCKABSORBERS BY22089845 1953-62 Corvette... 126.28ea 1962-67 Nova... 1972-76 Torino 1957-60 F100 REAR SHOCKABSORBERS BY22079850 1950-55 c series GM Truck... 131.72ea 1957-60 F100... FRONT SHOCKABSORBERS BY22049857 1963-82 Corvette... 131.72ea REAR SHOCKABSORBERS BY22039852 1964-70 Mustang... 122.06ea 1969-77 Maverick FRONT SHOCKABSORBERS BY22099854 1955-57 Chevy... 126.28ea 1950-55 C GM Truck... 1965-70 Galaxie REAR SHOCKABSORBERS BY22069856 1962-76 Dart... 122.06ea 1965-72 Charger... 1968-70 Mopar B body 1970-74 Mopar E body BY22089844 1958-64 Impala... 126.28ea REAR SHOCKABSORBERS BY22099867 1962 Dodge Dart... 122.06ea 1965-72 Charger... 1973-76 Charger 1968-70 B-Body... 1970-74 E-Body