E-2ECGC-PL-07A REVISED STARTING SERIAL # 07009 PARTS LIST MANUAL MODELS 2EC AND 2GC ELECTRIC MODEL GASOLINE MODEL PROPANE MODEL DUAL-DISC CONCRETE FLOOR GRINDERS SKU # MODEL # POWER OPTION 5000 2EC-.5HP ELECTRIC MOTOR.5HP 60Hz -PHASE 5/230V 5300-50 2EC-2B/50 ELECTRIC MOTOR 2HP 50Hz -PHASE 0/220V An ibuy Stores Company 50800 2EC-3B ELECTRIC MOTOR 3HP 60Hz -PHASE 230V 5800 2GC-5.5H HONDA GASOLINE ENGINE MODEL GXV60 5400 2GC-H HONDA GASOLINE ENGINE MODEL GXV340 54800 2GC-P HONDA PROPANE ENGINE MODEL GXV340 5V STARTER
E-2ECGC-PL-07A ILLUSTRATION : MAIN GROUPING
E-2ECGC-PL-07A PARTS LISTING - ILLUSTRATION : MAIN GROUPING ITEM # PART # DESCRIPTION QTY. 77022 MAIN FRAME & GEAR CASE, 2-EC/GC 2 77007 COVER, GEAR CASE, 2-EC/GC 3 0005 PLUG, HOLE 7/8 BRIGHT ZINC 4 0602 WASHER, FLAT /4 SAE ZINC 0 5 0038 WASHER, LOCK /4 ZINC 0 6 008 SCREW, CAP /4-20 X 3/4 0 7 77008 BEARING, BALL 4-HOLE FLANGE, ND 4 8 0450 WASHER, LOCK 7/6 ZINC 6 9 048 NUT, HEX 7/6-20 ZINC 6 0 77009 BEARING, BALL 3/4 4-HOLE FLANGE 2 0309 SCREW, CAP 3/8-24 X -/4 ZINC 4 2 08 WASHER, LOCK 3/8 ZINC 8 3 004 NUT, HEX 3/8-24 ZINC 8 4 7703 SHAFT, LARGE GEAR DIA X 7-3/6 L 2 5 7702 GEAR, SPUR 2 TOOTH (DRIVEN) 2 6 0007 PIN, ROLL 3/8 X 2-/2 2 7 770 SHAFT, PINION GEAR 3/4DIA X 7-3/8 L 8 0037 PIN, ROLL /4 X -/2 9 77053 GEAR, SPUR 25 TOOTH (PINION) 20 0009 WASHER, FLAT 3/4 SAE ZINC 2 9999 DISC ASSY. COMPLETE, MULTI-ACCY. LH (SEE ILLUS. 3) 22 8888 DISC ASSY. COMPLETE, MULTI-ACCY. RH (SEE ILLUS. 3) 23 0063 PIN, ROLL 3/8 X 2 2 24 7725 AXLE SPACER 9-5/8 L, 2-EC/GC 25 77209 AXLE SHAFT 3/4 DIA. X 7 L, 2-EC/GC 26 7903SH WHEEL, STL.HUB 8 X 2-/2 X 3/4 BRG. 2 27 7724 SPACER, WHEEL 3/8 L, 2-EC/GC 2 28 597 WASHER.755 ID X.25 OD X.060 THK (*USE AS REQ D.) 2* 29 86305 FLIP-HOLDER, WHEEL AXLE 2 30 039 SCREW, SET /4-20 X 5/6 2 3 032 SCREW, CAP /2-20 X -/4 2 32 032 WASHER, FLAT /2 SAE ZINC 2 33 0205 NUT, HEX LOCK /2-20 ZINC 2 34 7400 HANDLE BAR, 2-EC/GC 35 0608 GRIP, HAND MODEL AT 2 36 0029 SCREW, CAP 3/8-24 X -3/4 4 37 0025 WASHER, FLAT 3/8 SAE ZINC 8 An ibuy Stores Company 38 0004 NUT, HEX LOCK 3/8-24 ZINC 8 39 77077 HOOD, GRINDER, 2-EC/GC 40 0860 BOLT, TAP /4-20 X -/4 (FULL THD) 2 4 003 NUT, HEX /4-20 ZINC 2 42 0602 WASHER, FLAT /4 SAE ZINC 2 43 086 NUT, KEPS LOCK /4-20 ZINC 2
E-2ECGC-PL-07A ILLUSTRATION 2: SKIRT, VACUUM PORT & WATER HOOK-UP GROUPING
PARTS LISTING - ILLUSTRATION 2: SKIRT, VACUUM PORT & WATER HOOK-UP GROUPING E-2ECGC-PL-07A ITEM # PART # DESCRIPTION QTY. 7700 SKIRT GUARD, 2-EC/GC 2 0806 SCREW, CAP 5/6-8 X 5 3 080 WASHER, LOCK 5/6 ZINC 5 4 023 WASHER, FLAT 5/6 SAE ZINC 5 5 772 PANEL, VACUUM PORT 2, 2-EC/GC 6 03 SPACER, STEEL 9/6OD X 3/8ID X 7/32 2 7 774 RUBBER SEAL, SKIRT, 2-EC/GC 2-/2 x 56 8 7742 RUBBER SEAL, SKIRT REAR, 2-EC/GC 2-/2 x 6 9 7743 RETAINING STRIP, RUBBER SEAL, 2-EC/GC 0 77339 RETAINING BRKT., SKIRT CORNER 2 7744 RETAINING STRIP, REAR SEAL, 2-EC/GC 2 2 676 BOLT, CARRIAGE /4-20 X 5/8 GRADE 2 3 3 0602 WASHER, FLAT /4 SAE ZINC 3 4 086 NUT, KEPS LOCK /4-20 ZINC 3 5 86347 BRACKET, MULTI-VAC PORT 2-3 6 6502 CAP/PLUG 2 RED PLASTIC, FLANGED 7 0846 SCREW, CAP STSHW /4-20 X /2 4 8 0038 WASHER, LOCK /4 ZINC 4 9 773 HOSE, FLEX 2 ID X 32 L, GRINDERS 20 0766 CLAMP, HOSE, SAE #32, ADJ. TO 2-/2 2 2 56022 BRACKET, WATER VALVE 22 07 VALVE, BALL /2 FPT 23 8002 CONN., SWIVEL FEM. 3/4HOSE X /2MPT 24 0799 BARB ELBOW 90, 3/8HOSE X /4MPT 25 6508 HOSE, WATER 3/8 ID X 34 L 26 50069 CLAMP, HOSE, SAE #6, ADJ. TO 3/6 2 27 0982 TIE, CABLE, BLACK NYLON -/4 2 28 0694 BARB, 3/8HOSE X /8MPT 29 0772 ELBOW, STREET /8NPT X 45 (BRASS) 2 An ibuy Stores Company
E-2ECGC-PL-07A ILLUSTRATION 3: MULTI-ACCESSORY DISC ASSEMBLY ITEM # PART # DESCRIPTION QTY.* -8 8888 DISC ASSEMBLY COMPLETE, RIGHT-HAND (ITEMS THRU 8) 2 9999 DISC ASSEMBLY COMPLETE, LEFT-HAND (ITEMS THRU 8) 2 77088 77099 MULTI-ACCESSORY DISC ONLY R.H. FOR 8888 ASSEMBLY L.H. FOR 9999 ASSEMBLY 2 77020 RING, HUB CARRIER, 6-HOLE 3 02 RING, NEOPRENE, 4-/2 OD X /2 THK 2 4 7700 HUB, ALUMINUM 6-HOLE (GRINDER) 5 04 SCREW, SKT. HD. CAP 3/8-24 X 2-/4 6 6 03 SPACER, STEEL 9/6OD X 3/8ID X 7/32 6 7 00 SPACER, STEEL 5/8OD X 3/8ID X 3/8 6 8 0058 NUT, HEX LOCK 3/8-24 W/ NYLON PATCH 6 *QUANTITIES FOR ITEMS THRU 8 ARE PER EACH DISC ASSEMBLY RIGHT-HAND & LEFT HAND DISC REQUIRED PER 2-DISC GRINDER
E-2ECGC-PL-07A ILLUSTRATION 4: TOOL BOX & MULTI-DISC ACCESSORIES ITEM # PART # DESCRIPTION QTY. -3 2004 2005 TOOL BOX W/ HAMMER & PUNCH, BLACK TOOL BOX W/ HAMMER & PUNCH, RED 200 2002 TOOL BOX, BLACK (DYMA-SERTS ) TOOL BOX, RED (STRIP-SERTS ) 2 2003 HAMMER, BALL PEIN 6 OZ. 3 2006 PUNCH, GRINDER WEDGE, 5/8SQ X 9 4 260 WEDGE CG225, HARDWOOD 6 5 DYMA-SERT ACCY. W/ HOLDING CASE 6 ----- (SEE ILLUS. 5 FOR MORE DETAILS) 6 PCDYMA-SERT ACCY. W/ HOLDING CASE 6 ----- (SEE ILLUS. 5 FOR MORE DETAILS) 7 SCARIFIER ACCESSORY: 6 24 220 230 CG22 SCARIFIER HOLDING CASE ONLY CG222 TAW SCARIFIER, STANDARD INSERT CG223 TAW SCARIFIER, HEAVY-DUTY INSERT 8 2400 STRIP-SERT ASSEMBLY (SEE ILLUS. 6 FOR MORE DETAILS) 6 9 074 04 024 034 084 0 270 280 CG224V VITRIFIED GRINDING STONES: C0S SUPER COARSE C0 COARSE C24 MEDIUM C80 FINE C20 SUPER FINE CG0 WIRE BRUSH W/JR322 WEDGE WEDGE ONLY JR322, HARDWOOD 6 6 6
E-2ECGC-PL-07A ILLUSTRATION 5: DYMA-SERT & PCDYMA-SERT ASSEMBLIES ITEM # PART # DESCRIPTION QTY.* DYMA-SERT (SOLD SEPARATELY): 6 90 930 980 9250 9260 9270 9290 EG-X, 30-40 GRIT (GENERAL PURPOSE) EG-2X, 30-40 GRIT (ABRASIVE CONCRETE) EG-3X, 30-40 GRIT (EPOXY MORTARS) EG-5X, 50 GRIT (TERRAZZO) EG-7X, 80 GRIT (TERRAZZO) EG-9X, 20 GRIT (TERRAZZO) EG-23X, 200-230 GRIT (POLISHING) 2 EDP2PCD-30 PCDYMA-SERT (SOLD SEPARATELY) 6 3 920 CG22D DYMA-SERT HOLDING CASE W/PAD 6 4 940 RUBBER SHOCK PAD 6 5 92 DYMA-SERT HOLDING CASE 6 * QUANTITIES BASED ON 2-DISC GRINDER An ibuy Stores Company
E-2ECGC-PL-07A ILLUSTRATION 6: STRIP-SERT ASSEMBLY ITEM # PART # DESCRIPTION QTY. -8 2400 STRIP-SERT ASSY. WITH PRO TUNGSERT 6* -7 240 STRIP-SERT ASSY. WITHOUT PRO TUNGSERT 6* 2404 TUNGSERT HOLDER BOX, STRIP-SERT ** 2 2405 SCREW, SKT.HD.CAP /2-3 X 3.5,GR.5 ** 3 2403 TUNGSERT BLOCK, STRIP-SERT ** 4 2406 SPRING, COMP..765 OD X.25 FL ** 5 055 NUT, HEX NYLON LOCK /2-3 ** 6 573 SCREW, SKT. HD. CAP /4-20 X 3/4 ** 7 688 WASHER, HI-COLLAR LOCK.26ID X.363 ** 8 2407 PRO TUNGSERT (PACK OF 6) INCLUDES: ** 6 SCREWS & WASHERS, ITEMS 6 & 7 & HEX WRENCH, ITEM 9. 9 243 WRENCH, HEX L-KEY 3/6, SHORT-ARM * QUANTITIES BASED ON 2-DISC GRINDER ** QUANTITIES BASED ON STRIP-SERT ACCESSORY
E-2ECGC-PL-07A ILLUSTRATION 7: OPTIONAL PAD DRIVER DISC ASSEMBLY ITEM # PART # DESCRIPTION QTY.* 76040 PAD DRIVER DISC ASSEMBLY (INCLUDES ITEMS 2 THRU 5) 2 2 76042 HUB STUD, PAD DRIVER (GRINDER) 3 7604 DISC ONLY, PAD DRIVER 4 032 WASHER, FLAT /2 SAE ZINC 5 0304 SCREW, CAP /2-20 X 6 303 SILABIDE PAD, MEDIUM (NOT INCLUDED W/ ASSEMBLY) 2 *QUANTITIES FOR ITEMS 2 THRU 5 ARE PER EACH DISC ASSEMBLY QUANTITIES FOR ITEMS AND 6 ARE PER 2-DISC GRINDER
ILLUSTRATION 8: OPTIONAL SURFACER DISC ASSEMBLY E-2ECGC-PL-07A ITEM # PART # DESCRIPTION QTY.* -2 2222 2222C 3333 3333C 7722 7733 DISC ASSEMBLY COMPLETE, R.H. W/ STEEL CUTTERS. W/ CARBIDE CUTTERS DISC ASSEMBLY COMPLETE, L.H. W/ STEEL CUTTERS W/ CARBIDE CUTTERS DISC ONLY, SURFACER RIGHT HAND DISC LEFT HAND DISC 2 02 RING, RUBBER 4-/2 OD X /2 THK 2 3 77020 RING, HUB CARRIER, 6-HOLE 4 7700T HUB, CAST IRON, 6-HOLE 5 04 SCREW, SKT. HD. CAP 3/8-24 X 2-/4 6 6 03 SPACER, STL. 9/6OD X 3/8ID X 7/32 3 7 00 SPACER, STL. 5/8OD X 3/8ID X 3/8 6 8 0058 NUT, HEX LOCK 3/8-24 W/ NYLON PATCH 6 9 0054 NUT, HEX 5/6-8 ZINC 2 ITEM # PART # DESCRIPTION QTY.* 0 080 WASHER, LOCK 5/6 ZINC 2 0048 SCREW, CAP 5/6-24 X 3/4 2 2 77074 HOLDER, CUTTER SHAFT 3 3 0802 BOLT, CARRIAGE 3/8-6 X 3 4 0089 CLIP, SPEED NUT 3/8 3 5 0025 WASHER, FLAT 3/8 SAE ZINC 3 6 08 WASHER, LOCK 3/8 ZINC 3 7 0404 NUT, HEX 3/8-6 ZINC 3 8 77075 RETAINER, CUTTER SHAFT 3 9 77048 CG226 CUTTER SHAFT /2 X 3-/4 3 20 2230 CG227 SPACER /2 ID 33 2 CUTTERWHEEL 2206 2056 JRS50P 2 POINTED STEEL CP206T -3/4 6-POINT CARBIDE 24 8 *QUANTITIES FOR ITEMS 2 THRU 2 ARE PER EACH DISC ASSEMBLY RIGHT-HAND & LEFT HAND DISC REQD. PER 2-DISC GRINDER
An ibuy Stores Company E-2ECGC-PL-07A ILLUSTRATION 9: MOTOR & BELT DRIVE GROUPING FOR.5 HP UNITS
PARTS LISTING - ILLUSTRATION 9: MOTOR & BELT DRIVE GROUPING FOR.5 HP UNITS ITEM # PART # DESCRIPTION QTY. 76027 MOTOR, BALDOR.5HP-P-60HZ-5/230V-725RPM BALDOR SPEC. 36F57-385 (7/8 SHAFT) REPLACEMENT PARTS: 77039 60 76002 CAPACITOR, START, BALDOR, 850-950MFD 5V RESET BUTTON, BALDOR TPCRT3CA SWITCH, TOGGLE DPDT (SCREW TERM.) 6070 6524 66 6534 MOTOR, LEESON.5HP-P-60HZ-5/230V-740RPM LEESON CAT. NO. 3289 (-/8 SHAFT) REPLACEMENT PARTS: CAPACITOR, START, LEESON, 90MFD 25V RESET BUTTON, LEESON BRJ44DB SWITCH, TOGGLE DPDT (PUSH-ON TERM.) 2 77043 SWITCH, ROTARY CAM ON/OFF, LOVATO 3 77042 BRACKET, LOVATO ROTARY CAM SWITCH 4 663 SCREW, MACHINE 8-32 X /2 4 (LOCATED INSIDE OF SWITCH BOX) 5 0462 NUT, KEPS LOCK 8-32 ZINC 4 6 690 CLAMP, LOOM, 3/8 7 0038 WASHER, LOCK /4 ZINC 2 8 0846 SCREW, CAP STSHW /4-20 X /2 2 9 77043- SWITCH ADAPTER, PG6 TO /2 NPT 2 0 40066 STRAIN RELIEF /2NPT X.350-.450 2 676 STRAIN RELIEF 3/4NPT X.350-.450 2 77044 PLUG W/ 2/3 WIRE HARNESS, LOCKING 3 4004 CONNECTOR, LOCKING 20A/25V L5-20C 4 77045 WIRE HARNESS 2/3 X 42 LOA 5 0982 TIE, CABLE, BLACK NYLON -/4 2 6 77037 MOUNT, MOTOR 7 002 SCREW, CAP 3/8-24 X 4 8 0025 WASHER, FLAT 3/8 SAE ZINC 8 9 08 WASHER, LOCK 3/8 ZINC 4 20 004 NUT, HEX 3/8-24 ZINC 4 2 0802 BOLT, CARRIAGE 3/8-6 X FULL THD. 4 22 0404 NUT, HEX 3/8-6 ZINC 4 23 7707 77030 SHEAVE 3 OD X GR.B X 7/8 BORE (BALDOR.5HP) SHEAVE 3 OD X GR.B X -/8 BORE (LEESON.5HP) 24 ----- KEY (INCLUDED W/ MOTOR) 25 005 BELT 5L-270 (2/32 X 27 ) 26 3654 SHEAVE 5 OD X GR.B X 3/4 BORE 27 006 KEY 3/6SQ X -/2 28 5204 PLUG, RECT. HOLE, PLASTIC SNAP-IN E-2ECGC-PL-07A
E-2ECGC-PL-07A ILLUSTRATION 0: MOTOR & BELT DRIVE GROUPING FOR 2HP 50Hz & 3HP 60Hz UNITS
PARTS LISTING - ILLUSTRATION 0: MOTOR & BELT DRIVE GROUPING FOR 2HP 50Hz & 3HP 60Hz UNITS ITEM # PART # DESCRIPTION QTY. 609 MOTOR, BALDOR 2HP-PH-50HZ-0/220V-20/0A BALDOR CAT. #L3605T-50 REPLACEMENT PARTS: 4005 664 CAPACITOR, START, 645-774MFD 25V CAPACITOR, RUN, 40MFD 370V 6003 4005 6535 6536 2 6470 6460 6405 MOTOR, BALDOR 3HP-PH 60HZ-230V-4A BALDOR CAT. #L3609T REPLACEMENT PARTS: CAPACITOR, START, 645-774MFD 25V CAPACITOR, START, 460-552MFD 25V CAPACITOR, RUN, 60MFD 370V STARTER ACI #28839, 0V 50Hz 7.5-2.5A OL STARTER ACI #28840, 220V 50Hz 9.0-2.5A OL STARTER ACI #2884, 230V 60Hz.3-6.0A OL 3 0790 CONDUIT LOCK NUT /2 NP 2 4 430 STRAIN RELIEF /2NPT X.550-.650 2 5 77045 WIRE HARNESS 2/3 X 42 LOA 6 676 STRAIN RELIEF 3/4NPT X.350-.450 7 0740 CONDUIT LOCK NUT 3/4 NP 8 0982 TIE, CABLE, BLACK NYLON -/4 2 9 77044 PLUG W/ 2/3 WIRE HARNESS, LOCKING 0 40000 CONNECTOR, LOCKING 20A/250V L6-20C 86027 MOUNTING BRKT., STARTER 2 732 0384 SCREW, MACHINE 0-32 X -3/4 RPH SCREW, MACHINE 0-32 X RHP 3 0832 NUT, KEPS LOCK 0-32 ZINC 3 4 0846 SCREW, CAP STSHW /4-20 X /2 2 5 0038 WASHER, LOCK /4 ZINC 2 6 690 CLAMP, LOOM, 3/8 7 083 WASHER, LOCK, INT. TOOTH #0 8 0877 SCREW, CAP STSHW 0-24 X /2 9 5204 PLUG, RECT. HOLE, PLASTIC SNAP-IN 20 77037 MOUNT, MOTOR 2 002 SCREW, CAP 3/8-24 X 4 22 0025 WASHER, FLAT 3/8 SAE ZINC 8 23 08 WASHER, LOCK 3/8 ZINC 4 24 004 NUT, HEX 3/8-24 ZINC 4 25 0802 BOLT, CARRIAGE 3/8-6 X FULL THD. 4 26 0404 NUT, HEX 3/8-6 ZINC 4 27 77030 SHEAVE 3 OD X GR.B X -/8 BORE (2HP 50Hz) 79023 SHEAVE 3 OD X 2GR.B X -/8 BORE (3HP 60Hz) 28 ----- KEY (INCLUDED W/ MOTOR) 29 005 BELT 5L-270 (2/32 X 27 ) OR 2 30 3654 SHEAVE 5 OD X GR.B X 3/4 BORE (2HP 50Hz) 77058 SHEAVE 5 OD X 2GR.B X 3/4 BORE (3HP 60Hz) 3 006 KEY 3/6SQ X -/2 E-2ECGC-PL-07A 2
E-2ECGC-PL-07A ILLUSTRATION : ENGINE & BELT DRIVE GROUPING FOR HONDA GX60
PARTS LISTING - ILLUSTRATION : ENGINE & BELT DRIVE GROUPING FOR HONDA GX60 ITEM # PART # DESCRIPTION QTY. 76020 ENGINE, HONDA GXV60UH2-N2 WITH STANDARD DUAL ELEMENT AIR CLEANER 2 580 MANUAL CHOKE KIT FOR HONDA GXV60 (INCLUDES ITEMS 3 THRU 9) 3 582 BRKT., CHOKE CONTROL, GXV60 4 58 LEVER, CHOKE CONTROL, GXV60 5 584 CAP, FLAT RED.062 X.75 X 6 930 DECAL, CHOKE 5/8 X 5/8 7 0834 SCREW, CAP /4-20 X /2 8 586 WASHER, BELLEVILE.500 X.255 X.08 9 050 NUT, HEX NYLON LOCK /4-20 0 54 BARB, PUSH-ON 3/8 HOSE X0MM X.25 7206 HOSE, PUSH-ON 3/8 ID X 2-/4 L 2 544 BARB, PUSH-ON 3/8 HOSE X /4FPT 3 0776 PIPE PLUG /4 NPT (BRASS) 4 40388 CABLE, THROTTLE, LEVER-TYPE 24 5 0877 SCREW, CAP STSHW 0-24 X /2 2 6 083 WASHER, LOCK, INT. TOOTH #0 2 7 0982 TIE, CABLE, BLACK NYLON -/4 8 520A 50084 083 0877 0970 36042 SWITCH W/ WIRES, ROCKER RED ON-OFF ADDITIONAL PARTS REQ D. (NOT SHOWN); TERM., RING #0 6-4GA. INSULATED WASHER, LOCK, INT. TOOTH #0 SCREW, CAP STSHW 0-24 X /2 CONN., WIRE QUICK-SPLICE 8-4 GA. CLIP, NATURAL CORD, /8 X /4 2 9 76023 MOUNT, ENGINE, VERT. SHAFT 20 0048 SCREW, CAP 5/6-24 X 3/4 2 2 080 WASHER, LOCK 5/6 ZINC 4 22 0342 SCREW, CAP 5/6-8 X -/2 2 23 023 WASHER, FLAT 5/6 SAE ZINC 2 24 0054 NUT, HEX 5/6-8 ZINC 2 25 0802 BOLT, CARRIAGE 3/8-6 X FULL THD. 4 26 0025 WASHER, FLAT 3/8 SAE ZINC 4 27 08 WASHER, LOCK 3/8 ZINC 4 28 0404 NUT, HEX 3/8-6 ZINC 4 29 009 KEY, WOODRUFF 5/32 X 5/8 (#505) 30 77024 CLUTCH, CENTRIFUGAL 3.5 X GR X 7/8 3 72006 WASHER, -/4OD X 3/32ID X /8THK 32 08 WASHER, LOCK 3/8 ZINC 33 0336 SCREW, CAP 3/8-24 X 2-/4 34 005 BELT 5L-270 (2/32 X 27 ) 35 3654 SHEAVE 5 OD X GR.B X 3/4 BORE 36 006 KEY 3/6SQ X -/2 An ibuy Stores Company E-2ECGC-PL-07A
An ibuy Stores Company E-2ECGC-PL-07A ILLUSTRATION 2: ENGINE & BELT DRIVE GROUPING FOR HONDA GX340
PARTS LISTING - ILLUSTRATION 2: ENGINE & BELT DRIVE GROUPING FOR HONDA GX340 ITEM # PART # DESCRIPTION QTY. 76004 502 ENGINE HONDA GASOLINE MODELGXV340UT2-DX3 (SHOWN) HONDA PROPANE MODEL GXV340UT2-DP23 (ILLUS. 3) 2 590 MANUAL CHOKE KIT - GASOLINE ENGINE ONLY (INCLUDES ITEMS 3 THRU 0) 3 583 LEVER, CHOKE CONTROL, GXV340 4 930 DECAL, CHOKE 5/8 X 5/8 5 584 CAP, FLAT RED.062 X.75 X 6 585 SCREW, MACHINE M6 X 6MM PHILLIP HD 7 588 WASHER.265 ID,.50 OD,.029-.035 THK 8 587 WASHER, FIBER.75 X.25 X.093 9 586 WASHER, BELLEVILE.500 X.255 X.08 0 28026 NUT, HEX NYLON LOCK M6 X MM 40388 CABLE, THROTTLE, LEVER-TYPE 24 2 0877 SCREW, CAP STSHW 0-24 X /2 2 3 083 WASHER, LOCK, INT. TOOTH #0 2 4 0982 TIE, CABLE, BLACK NYLON -/4 5 689 ADAPTER, 20MM X.5 TO /4FPT 6 0657 BARB, PUSH-ON 3/8 HOSE X /4MPT 7 7206 HOSE, PUSH-ON 3/8 ID X 2-/4 L 8 544 BARB, PUSH-ON 3/8 HOSE X /4FPT 9 0776 PIPE PLUG /4 NPT (BRASS) 20 520A 50084 083 0877 0970 36042 SWITCH W/ WIRES, ROCKER RED ON-OFF ADDITIONAL PARTS REQ D. (NOT SHOWN); TERM., RING #0 6-4GA. INSULATED WASHER, LOCK, INT. TOOTH #0 SCREW, CAP STSHW 0-24 X /2 CONN., WIRE QUICK-SPLICE 8-4 GA. CLIP, NATURAL CORD, /8 X /4 2 76023 MOUNT, ENGINE, VERT. SHAFT 22 0048 SCREW, CAP 5/6-24 X 3/4 2 23 080 WASHER, LOCK 5/6 ZINC 4 24 0606 SCREW, CAP 5/6-8 X -/4 2 25 023 WASHER, FLAT 5/6 SAE ZINC 4 26 0054 NUT, HEX 5/6-8 ZINC 4 27 0802 BOLT, CARRIAGE 3/8-6 X FULL THD. 4 28 0025 WASHER, FLAT 3/8 SAE ZINC 4 29 08 WASHER, LOCK 3/8 ZINC 4 30 0404 NUT, HEX 3/8-6 ZINC 4 3 76024 CLUTCH, CENTRIFUGAL 3.5 X 2GR X 32 0307 KEY /4SQ X 2-/4 33 005 BELT 5L-270 (2/32 X 27 ) 2 34 77058 SHEAVE 5 OD X 2GR.B X 3/4 BORE 35 006 KEY 3/6SQ X -/2 An ibuy Stores Company E-2ECGC-PL-07A 2
An ibuy Stores Company E-2ECGC-PL-07A ILLUSTRATION 3: PROPANE GROUPING
PARTS LISTING - ILLUSTRATION 3 : PROPANE GROUPING E-2ECGC-PL-07A ITEM # PART # DESCRIPTION QTY. 502 ENGINE, HONDA PROPANE MODEL GXV340T2-DP23 (SEE ILLUS. 2) 2 526 STARTER KIT, ELECTRIC 20 VOLT AC (INCLUDES POWER CORD - NOT SHOWN) 3 634 SCREW, CAP M6 X.0P X 20MM 2 4 0038 WASHER, LOCK /4 ZINC 2 5 003 SCREW, CAP /4-20 X 2 6 0602 WASHER, FLAT /4 SAE (USE 2 FOR SHIMS WHEN REQ D.) 4 7 003 NUT, HEX /4-20 ZINC 2 8 502 VAPOR KIT FOR HONDA GXV340T2-DP23 KIT INCLUDES: HIGH PRESSURE VAPOR REGULATOR G-SE-50 2A-C.... ( EA.) FUELOCK VAPOR FILTER G-SE-VFF30-2-4............. ( EA.) HIGH PRESSURE HOSE W/ FITTINGS -/2........... ( EA.) HIGH PRESSURE HOSE W/ FITTINGS 38-/2........... ( EA.) HOSE, PUSH LOCK 3/8 ID X 32 L..................... ( EA.) HOSE, VACUUM 3/6 ID X 48 L...................... ( EA.) REGO 74F FEMALE COUPLING, BRASS............. ( EA.) FITTING /4NPT X 3/8FLARE 90DEG, BRASS........... (3 EA.) FITTING 3/8 PIPE X 3/8 HOSE BARB ELBOW, BRASS... ( EA.) FITTING /8NPT X 3/6 HOSE, ELBOW, BRASS........ ( EA.) FITTING /8NPT X 3/6 HOSE BARB, BRASS.......... ( EA.) FITTING 3/6 TEE, NYLON.......................... ( EA.) MOUNTING SCREWS............................... (4 EA.) 9 720 CLAMP, HOSE SPRING-TYPE /8 BLACK 02-04 6 0 50069 CLAMP, HOSE, SAE #6, ADJ. TO 3/6 2 77063 PROPANE REGULATOR MOUNT PLATE 2 0846 SCREW, CAP STSHW /4-20 X /2 4 3 0038 WASHER, LOCK /4 ZINC 4 4 77062 PROPANE TANK MOUNT 5 0908 BOLT, CARRIAGE 3/8-6 X 2-/2 4 6 08 WASHER, LOCK 3/8 ZINC 4 7 0404 NUT, HEX 3/8-6 ZINC 4 8 7706- PROPANE TANK CRADLE BRACKET ONLY 9 0802 BOLT, CARRIAGE 3/8-6 X FULL THD. 4 20 0025 WASHER, FLAT 3/8 SAE ZINC 4 2 08 WASHER, LOCK 3/8 ZINC 4 22 0404 NUT, HEX 3/8-6 ZINC 4 23 7706-2 PROPANE TANK STRAP W/ HINGE 24 7706-3 PROPANE TANK CLAW BRACKET 25 7706-4 PROPANE TANK TOGGLE CLAMP 26 66 SCREW, FLAT HD SLT /4-20 X 2 27 0602 WASHER, FLAT /4 SAE 2 28 086 NUT, KEPS LOCK /4-20 ZINC 2 29 530 PROPANE TANK 20LB. HORZ./VERT. 30 922 DECAL, ARROW, RED, 3 X 3 An ibuy Stores Company
E-2ECGC-PL-07A ILLUSTRATION 4: OPTIONAL WEIGHT BLOCKS & TRAY An ibuy Stores Company ITEM # PART # DESCRIPTION QTY. 77049 WT-55 WEIGHT 55 LBS.(25 KG) OR 2 2 77050 WT- WEIGHT HOLDING TRAY