Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces Avoid mounting components or routing wires near moving parts Tape or loom wires under hood for protection and appearance Use grommets when routing wires through metal surfaces Use a voltmeter for testing and verifying circuits Technical Support For Authorized Dealers - (800) 421-3209 Hours: 8:00 a.m. - 7:00 p.m. EST Monday thru Friday 10:00 a.m. - 2:00 p.m. EST Saturday This device complies with part 15 of the FCC rules and with RSS-210 of the industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Y7 INS0872 Rev. A 10/98
System Layout RED SIREN OUTPUT (-) BLACK ORANGE ORANGE/BLACK PARKING LIGHT OUTPUT (+) WHITE RED WHITE RED BLACK BLUE/BLACK GREEN/BLACK STARTER KEY STARTER MOTER +12 VOLTS CHASSIS GROUND DOOR LOCK OUTPUT (-) DOOR UNLOCK OUTPUT (-) SHOCK SENSOR WHITE YELLOW GREEN GRAY PINK BLUE BROWN BROWN POSITIVE DOOR TRIGGER NEGATIVE DOOR TRIGGER NEGATIVE HOOD/TRUNK TRIGGER BLACK BLACK STATUS INDICATOR RED DISARM BUTTON SWITCHED POWER VALET SWITCH +12 VOLTS 2 Refer to Wire Color / Location Chart for specific wire color, location, and polarity information.
1. Installation A. Siren (ORANGE on 3-Pin Connector) Mount bell housing downwards. Use at least two (2) screws to secure siren to mounting location. Connect siren BLACK wire to module ORANGE wire. Connect siren RED wire to a fused +12-volt source. B. 12V+ Main Feed (RED) Connect at vehicle battery or at main 12-volt lead at ignition switch harness. Circuit Verification - Target wire registers voltage at all times. C. 12V+ Switched Feed (BLUE on 7-Pin Connector) Connect at switched 12-volt lead at ignition switch harness. Circuit Verification - Target wire registers voltage when ignition key is turned to the ON position and START position. D. Ground (BLACK) Attach to grounded metal point of vehicle chassis. Note: When installing multiple components (such as an alarm and remote starter), ground the units separately. E. Starter Interrupt (WHITE/RED and WHITE) Connect to vehicle starter wire at ignition switch harness. Circuit Verification - Target wire registers voltage only when ignition key is turned to the START position. Circuit Verification after starter wire is cut: KEY SIDE of starter wire registers voltage when ignition key is turned to the START position. MOTOR SIDE of starter wire registers no voltage. Note: Some vehicles have two starter wires. If so, cut both and connect to the alarm module. F. Door Pin Switches (YELLOW or WHITE on 7-Pin Connector) Circuit Verification - Refer to Vehicle Wire Color and Location Chart for circuit type and location, or verify the vehicle wire using the following guideline: Positive Systems - Target wire registers voltage when any door is opened. Negative Systems - Target wire registers ground when any door is opened. 3
G. Parking Lights (ORANGE/BLACK Wire on 3-Pin Connector) Circuit Verification - Refer to Vehicle Wire Color and Location Chart for circuit type and location, or verify the vehicle wire using the following guideline: Positive Systems - Target wire registers voltage when parking lights are on. Negative Systems - Target wire registers ground when parking lights are on. Connections Positive System Negative System Parking Lights Connect to Target wire Add relay (dia. 2) Parking Light System - Relay Needed Diagram 2 H. Hood / Trunk Pin Switch (GREEN Wire on 7-Pin Connector) Circuit Verification - Refer to Vehicle Wire Color and Location Chart for circuit location, or install a pin switch and connect to the module GREEN wire. I. Power Door Locks (BLUE/BLACK and GREEN/BLACK) Circuit Verification - Refer to Vehicle Wire Color and Location Chart for circuit type and location. Connections Type 1 Type 2 Type 3 Type 4 Other Door Locks Dia. 3 Dia. 4 Dia. 5 Dia. 6 See specifications in Vehicle Wire Color / Location Guide or call Technical Support 4
Diagram 3 Type 1 - Positive 3-Wire Door Lock System Diagram 4 Type 2 - Positive 5-Wire Door Lock System Diagram 5 Type 3 - Negative 3-Wire Door Lock System 5
1. Installation I. Power Door Locks (cont.) Diagram 6 Type 4 - Vacuum Door Lock System Resistors Lock Output (-) Unlock Output (-) If door lock system requires (+), connect to 12V+. If system requires (-), connect to Ground. Vehicle Door Lock Switch or Plunger 20A 12V+ To Control Relays Type 5 - Multiplex Door Lock System J. Status Indicator (GRAY Wire on 7-Pin Connector) Locate a visible location on the dash with 1 1 /2 clearance. Drill 1 /4 hole and snap the status indicator in place. Connect the status indicator BLACK wire to the module GRAY wire. Connect the status indicator RED wire to a fused +12-volt source. K. Impact Detector Mount the impact detector to the steering column or a sturdy brace or wire harness. Plug the impact detector onto the 4-pin module connector. 6
1. Installation 7 TAB ONLY L. Override/Programming Button The override/programming button must be installed for all installations Find a suitable mounting location for the override/programming button. The selected mounting location should be as difficult as possible for an unauthorized person to find. It is recommended that the override button be mounted in different location in each installation. Drill a 9/32 hole mounting hole in the selected mounting location and mount as shown. Connect one of the override button wires to the module brown wire. Connect the remaining override / programming button wire to a solid chassis ground. M. Valet Switch The valet switch must be installed on all automatic arming systems. The automatic arming option is enabled from the factory. If automatic arming is not desired, the automatic arming option maybe disabled during the programming steps. Find a suitable mounting location underdash for the valet switch that is accessible while sitting in the driver s seat. Drill a 1/4 mounting hole and mount the valet switch Connect one of the valet switch wires to the module PINK wire. Connect the remaining valet switch wire to a solid chassis ground. 2. System Power-Up Check all connections and wire routing. Turn ignition to the ON position. Replace the 20-amp fuse in the module RED wire. Turn the ignition off. 7
Programming Remote Transmitters Note: Each system module has four slots, or memory locations, to store remote transmitter codes, giving it the ability to operate from up to four remote transmitters. For proper operation, a transmitter code must be stored into each memory slot. When using less than four transmitters, follow the suggested programming parameters: One Remote Transmitter - Program four (4) times Two Remote Transmitters - Program each transmitter two (2) times Three Remote Transmitters - Program one transmitter twice, and each remaining transmitter once. 1. Open the driver s door and leave open. 2. If not already on, turn the ignition key to the RUN position. 3. Press and hold the programming button. In 15 seconds the system will chirp the siren and cycle the door locks three (3) times. 4. Release the override/programming button. The system is now in the transmitter learn mode. 5. Wait five (5) seconds. 6. Press ARM button on the first transmitter. The system will chirp the siren and cycle the door locks one time to indicate that this transmitter code has been learned. 7. Repeat step 6 for transmitter #2 (programming each transmitter twice). 8. Turn the ignition key off to exit the learn mode. 9. Close all doors to reset the system operation. 8
3. Programming Selectable Options Note: You can go into option programming mode without exiting the transmitter learn mode. To do so, do not turn the ignition key off or close the doors at the end of the transmitter programming section and proceed directly to step 2 below. 1. Enter the transmitter programming mode as indicated above. 2. Press and release the programming button one time. The siren will chirp three (3) times to indicate the system is in the option programming mode. 3. Press the ARM button one time to select option #1. The siren will chirp one time. Pressing the disarm button on a programmed transmitter toggles the selected option s state on or off. The status indicator (LED) will display the state of the selected option. Pressing the ARM button on a programmed transmitter selects the next option. The siren will emit a number of short chirps corresponding to the selected option number. Pressing ARM and DISARM buttons at the same time will reset all options to their factory preset states. The siren will chirp and the door locks will cycle once to indicate that the options have been reset to their factory preset programming. 4. When all options are set as desired, turn the ignition key off to exit the options programming mode. 5. Close all doors to reset the system operation. Button 1 Press to Advance to Next Option Press BOTH Buttons (1 and 2) to Reset all Options to Factory Settings Button 2 Press to Turn Option ON or OFF Status Indicator Displays Option Status (ON or OFF) Number of Siren Chirps Indicate Option Number Status Indicator Option Number and Description Bold Type Indicates Factory Settings ON OFF 1 Siren chirps when arming and disarming YES NO 2 System arms automatically 60 seconds after last door is closed YES NO 3 Doors lock when all doors are closed and ignition is turned on YES NO 4 Doors unlock when ignition is turned off YES NO 5 Do not change 6 Do not change 7 Doors lock when system arms automatically 2 YES NO 8 Door lock / unlock output duration is (1) 1 / 2 second or (2) 6 seconds (2) (1) 2 Ignore this option if Option 2 is NOT activated 9
Testing the Alarm System Arming and Disarming Close all doors and press ARM. Press Disarm. All doors lock Siren chirps two times / parking lights flash Status indicator flashes steadily All doors unlock Siren Chirps once / parking lights flash Status indicator turns off Alarm Triggering / Starter Interrupt / Trip ID / Lock Options Arm system. Wait 10 seconds, then Siren sounds / parking lights flash open door. With siren sounding, attempt to Vehicle will not start start vehicle. Wait until siren stops, then press DISARM. Siren chirps / parking lights flash 4 times (System was triggered) Press DISARM again. Siren chirps two times (System was triggered by door) Close doors and attempt to start vehicle. Vehicle starts Doors lock (if Ignition Lock Option is activated) Turn ignition off Doors unlock (if Ignition Unlock Option is activated) Panic Press both buttons Siren sounds / parking lights flash for 30 seconds. Passive Arming (Test only if Passive Option is activated) Enter vehicle and close doors. Turn ignition Alarm arms one minute after door is closed on for five seconds, then turn off. Exit vehicle Doors lock (if Passive Lock Option is activated) and close doors. Valet (Test only if Passive Option is activated) With system disarmed, turn ignition on, Status Indicator Flashes twice (enters Valet Mode) then press DISARM. Turn ignition off. Status indicator emits a double-blink pattern. Close all doors and press ARM. Double-blink pattern stops, and system arms. Antenna Placement Keep the antenna as straight as possible, and route away from vehicle harnesses. 10
11