JPRO Professional Diagnostic Software WHAT S NEW Dashboard Brake Lamp Tests on Bendix EC-80 braking systems. Ability to resolve partial Chassis ID to full VINs on Mack/Volvo vehicles. Improved powertrain fault readings on EPA 13 Mack/Volvo vehicles. JPRO Medium-Duty Command Module Sprinter Improved VIN readings on Sprinter vehicles to allow better bi-directional test coverage. JPRO Heavy-Duty with OnCommand Connection Ability to edit and correct mileage and VIN information upon data submission to OnCommand service. JPRO with ASIST Ability to edit and correct mileage and VIN information upon data submission to ASIST service. FEATURE LIST JPRO Professional Diagnostic Software Includes all features provided by the following modules: JPRO Heavy-Duty Module JPRO Heavy-Duty Command Module Cummins JPRO Heavy-Duty Command Module Detroit JPRO Heavy-Duty Command Module International JPRO Heavy-Duty Command Module Mack and Volvo JPRO Heavy-Duty Command Module Paccar JPRO Medium-Duty Command Module Ford JPRO Medium-Duty Command Module GM JPRO Medium-Duty Command Module Isuzu JPRO Medium-Duty Command Module Sprinter Also, includes the following features: Dashboard Brake Lamp Tests on all Wabco and Bendix EC-80 braking systems. Wheel Speed Window Test and Wheel Speed Chart Test used to verify and test wheel speed sensors on all tractor and trailer braking systems. Access to historical fault data from previous JPRO connections which can be used to identify intermittent vehicle issues. NOTE: Requires internet access. Ability to remove access to setting road and cruise speed limits. If interested in limiting these capabilities, contact Noregon support (support@noregon.com). Ability to resolve partial Chassis ID to full VINs on Mack/Volvo vehicles. Improved powertrain fault readings on EPA 13 Mack/Volvo vehicles. 1
JPRO Professional Diagnostic Software with Next Step Includes all features provided by the following modules: All features in JPRO Professional Diagnostics Software plus JPRO Next Step Module JPRO Professional Diagnostic Software for AU Includes all features provided by the following modules: JPRO Heavy-Duty Module JPRO Heavy-Duty Command Module Cummins JPRO Heavy-Duty Command Module Detroit JPRO Heavy-Duty Command Module International JPRO Heavy-Duty Command Module Paccar JPRO Medium-Duty Command Module Isuzu JPRO Medium-Duty Command Module Sprinter NOTE: Mack and Volvo, Ford, GM and JPRO Next Step are not supported in Australia. Also, includes the following features: Dashboard Brake Lamp Tests on all Wabco and Bendix EC-80 braking systems. Wheel Speed Window Test and Wheel Speed Chart Test used to verify and test wheel speed sensors on all tractor and trailer braking systems. Access to historical fault data from previous JPRO connections which can be used to identify intermittent vehicle issues. NOTE: Requires internet access. Ability to remove access to setting road and cruise speed limits. If interested in limiting these capabilities, contact Noregon support (support@noregon.com). JPRO Heavy-Duty Features Heavy Duty supports all standard Heavy Duty vehicles. Supports the heavy duty SAE J1587/J1708, J1939, ISO 15765 and KWP2000 messages. Support for trailer diagnostics using the JPRO Trailer Diagnostic adapter or the JPRO DLA+ PLC and the PLC 7- way connector. Graphically displays data using thermometers, gauges, etc. on the Data Monitor. Display of data related to reported faults in Data Monitor. Ability to define custom groups of related data parameters to display in Data Monitor. Power Diagram and Electrical Assistance available in Data Monitor to aid in the diagnosis of electrical problems. FMI Assistance providing technician friendly descriptions for fault code FMI values from both the Fault display and the Data Monitor. Aftertreatment screen display of data, including EGR data for rapid troubleshooting of the aftertreatment system. Emissions Assistance from the Aftertreatment screen to aid in troubleshooting emissions problems. Clear indication of overall vehicle health taking into account: Active Faults Present Consumable Fluid(s) Low Cannot Detect ABS (on 2001 or newer vehicles) Battery Voltage Low No 1939 Data (on 2009 or newer vehicles) 2
Search mechanism to link to troubleshooting guides. Provides data bus utilization statistics on live heavy duty vehicle connections. Launches OEM component diagnostic applications in Fault Code Information. Simply click on the OEM application icon to launch the application for more information about that component. Displays the trailer lamp status on tractor brake key data point s window. Consumable Fluid screen to monitor fluids used by vehicle and inform user of low levels. Support for proprietary sensor data on Detroit, Cummins and International engines. Support for reading and display of HD-OBD Emissions faults in standard fault display. Support for Mack, Volvo and Prevost proprietary fault codes for all components. Support reading Cummins Proprietary Fault Codes on all EPA07 and newer Cummins engines. Support reading Bendix Proprietary Fault Codes on all EC-80 braking systems. Support for 2016 Peterbilt and Kenworth trucks with or without the Paccar Y-cable (PACCAR P/N 42-02848) available from the PACCAR dealer network. Support for all Paccar Body Controllers and engines including clearing faults. NOTE: Paccar Body Controller faults are only supported on 2007 and newer Kenworth and Peterbilt trucks. NOTE: Paccar Body Controller faults on the KWP2000 protocol can only be read when using the JPRO DLA+, DLA+ Wireless, DLA+ 2.0 or DLA+ 2.0 Wireless adapter. If using the JPRO DLA+ or JPRO DLA+ Wireless adapter, please ensure the label on the back of the adapter indicates it is Rev P Compatible. JPRO Heavy-Duty Command Module Cummins Bi-Directional support for Cummins engines: Aftertreatment Maintenance Reset Cylinder Cut Out DPF Service Regen EPA 07 to EPA 13 all ISB, ISC, ISL, ISM and ISX EPA 02 to EPA 13 all ISB, ISC, ISL, ISM and ISX EPA 07 to EPA 13 all ISB, ISC, ISL, ISM and ISX Fuel Injector Calibration Fuel Injector Reset Fuel Leakage Test Trip Reset VGT Electronic Actuator Installation and Calibration NOTE: Can be started from either the Bi-Directional test selection or the Aftertreatment Diagnostics screen. EPA 07 and 10 ISC, ISL, and ISX (12L and 15L) with Common Rail Fuel Systems EPA 13 all ISB, ISL, and ISX EPA 10 and 13 Common Rail Fuel Systems EPA 07 to EPA 13 all ISB, ISC, ISL, ISM and ISX EPA 10 and 13 ISB, ISC, ISL, and ISX (12L and 15L) 3
VGT Hysteresis Test EPA 10 and 13 ISB, ISC, ISL, and ISX (12L and 15L) with Common Rail Fuel Systems JPRO Heavy-Duty Command Module Detroit Bi-Directional support for Detroit engines: Cylinder Cut Out Cruise Speed Limits DPF Service Regen DPF Ash Accumulator Reset Idle Shutdown Enable/Disable and Time Set Road Speed Limits SCR Output Component Test SCR Airless Doser System (ADS) Self Check 2000 to 2017 all Series 50, 55, 60, DD13, DD15, and DD16 EPA 10 to EPA 13 for all DD13, DD15 and DD16 EPA 07 to EPA 13 all DDEC VI Series 60, DD13, DD15 and DD16 NOTE: Can be started from either the Bi-Directional test selection or the Aftertreatment Diagnostics screen. EPA 07 Series 60 and DD15 EPA 10 to EPA 13 for all DD13, DD15, and DD16 EPA 10 to EPA 13 for all DD13, DD15, and DD16 EPA 10 to EPA 13 for all DD13, DD15 and DD16 EPA 10 to EPA 13 for all DD13, DD15, and DD16 EPA 13 all DD13, DD15, and DD16 JPRO Heavy-Duty Command Module International Bi-Directional support for EPA 07 to EPA 13 engines: Aftertreatment Reset CDPF Reset Cylinder Cut Out DOC/DPF Replacement Reset DPF Service Regen KOER Standard Test EPA 07 and EPA 10 Maxxforce 11 and 13 engines EPA 10 Maxxforce 7, DT, 9 and 10 engines EPA 07 Maxxforce 7, DT, 9, 10, 11, and 13 engines EPA 10 Maxxforce 9, DT, 10, 11, and 13 engines EPA 13 Maxxforce 9, DT, 10, 11, 13 and N series engines EPA 13 N series engines EPA 07 Maxxforce 7, DT, 9, 10, 11, and 13 engines EPA 10 Maxxforce 7, DT, 9, 10, 11, and 13 engines EPA 13 Maxxforce 7, DT, 9, and 10 engines EPA 07 to EPA 13 Maxxforce 7, 9 and 10 engines EPA 13 N9 and N10 engines 4
SCR Faults Reset EPA 13 N series engines JPRO Heavy-Duty Command Module Mack and Volvo Supports all Mack, Volvo and Prevost vehicles. Displays all standard and proprietary fault codes for all components. Mack and Volvo Specific Reports including: Trip Report Life of Vehicle Report NOTE: Reports only available on Mack EPA07 and newer vehicles with the DataMax parameter enabled. NOTE: Reports only available on Volvo 2012 and newer with the DataMax parameter enabled. Bi-Directional support for Mack and Volvo EPA07, EPA10 and EPA13 engines includes: Cylinder Cut Out EPA 07 to EPA 13 DPF Service Regen EPA 07 to EPA 13 DPF System Reset EPA 07 to EPA 13 Learned Data Reset EPA 07 to EPA 13 Set Cruise Max and Min Speeds EPA 07 to EPA 13 Set Road Speed Limit EPA 07 to EPA 13 Set Idle Shutdown Time EPA 07 to EPA 13 Trip Reset Enable or Disable Cruise Control EPA 07 to EPA 13 Mack EPA 07 and newer vehicles with the DataMax parameter enabled. Volvo 2012 and newer with the DataMax parameter enabled. NOTE: Mack and Volvo Coverage requires internet access at least once a month. Failure to provide internet access will result in the application limiting use and eventually shutting off the module features. NOTE: Mack and Volvo Coverage only supports the following adapters: Noregon DLA+ 2.0, DLA+, DLA+ 2.0 Wireless, DLA+ Wireless and DLA+ PLC Vocom 88890300 NEXIQ USB-Link NEXIQ USB Link 2 JPRO Heavy-Duty Command Module Paccar Bi-Directional support for EPA 10 to EPA 13 engines: 5
Automated Cylinder Performance Test EPA 10 and EPA 13 MX engines JPRO Medium-Duty Command Module Ford Supports 2004 to 2016 Ford models: F-series Econoline E-series Transit Connect Transit vehicles Supports the medium duty ISO 15765 and ISO 14229 messages. Gives users the ability to read and clear faults, read freeze frames, read sensor data, and display emission test results. Enables users to run diagnostic tests on components such as the KOEO On Demand Self Test. Enables support for GM, Sprinter, Isuzu, Fuso and Hino OBD II emissions faults and data. 6
JPRO Medium-Duty Command Module GM Supports the following vehicle models from 2002 to 2016: GMC and Chevy Full Sized Trucks 1500, 2500 and 3500 GMC Express and Chevy Savana All GM Medium Duty vehicles NOTE: Only the powertrain components are supported on 2014-2016 GM vehicles. Supports the medium duty J1850 VPW and GMLAN messages. Gives users the ability to read and clear faults, read freeze frames, read sensor data, and display emission test results. Supports cylinder cutouts on all diesel and gasoline engines on year s 2002-2013 (except in GM vehicles with CAT engines). Tests for 2010-2012 Express/Savana with 6.0L Gas Engines. Enables support for Ford, Sprinter, Isuzu, Fuso and Hino OBD II emissions faults and data. JPRO Medium-Duty Command Module Isuzu Supports the following vehicle models from 2008-2017 with either the 5.2L (4HK1) or 3.0L (4JJ1) engine in both North America and Australia: N-Series faults and data (engine, DEF and transmission only) F-Series faults (engine and DEF only) Supports the medium duty GMLAN messages. Gives users the ability to read and clear faults and read freeze frames. Displays emission test results in North America. Bi-Directional support for: Cylinder Cut Out DPF Service Regen 5.2L (4HK1) or 3.0L (4JJ1) engine in North America 5.2L (4HK1) or 3.0L (4JJ1) engine in North America 7
JPRO Medium-Duty Command Module Sprinter Supports 2007 to 2015 Sprinter vehicles. Sprinter Module gives users the ability to read and clear faults, read sensor data, and display emission test results. Enables support for Ford, GM, Isuzu, Fuso and Hino OBD II emissions faults and data. Bi-Directional support for: Cylinder Cut Out Compression Test DPF Service Regen Injector Quantity Adjustment Initialize Rail Pressure Oil Change Reset Display Dimmer Test Routine Gauge Sweep Test LCD Display Test Routine Speaker Test Routine Tire Pressure Monitor Test EPA 07 Diesel Engine EPA 07 Diesel Engine EPA 07 Diesel Engine EPA 07 Diesel Engine EPA 07 Diesel Engine 2007 2015 Instrument Cluster 2007 2015 Instrument Cluster 2007 2015 Instrument Cluster 2007 2015 Instrument Cluster 2007 2015 Instrument Cluster 2007 2015 TPM 8
JPRO Next Step Module Integration with Mitchell 1 TruckSeries. View Mitchell 1 troubleshooting information for a particular engine fault with a single click within JPRO Commercial Vehicle Diagnostics. Automatically link to troubleshooting guides for Wabco, Bendix and Haldex brakes as well as Eaton transmissions. NOTE: The JPRO Next Step Module requires internet access at least once a month. Failure to provide internet access will result in the eventual shutting off the module features. JPRO Heavy-Duty with OnCommand Connection Upload vehicle connection data to Navistar's OnCommand service. Ability to edit and correct mileage and VIN information upon data submission to OnCommand service. NOTE: The OnCommand module requires either a heavy-duty or medium-duty module to be able to connect to vehicles. JPRO with ASIST Upload vehicle connection data (of any vehicle make) to the ASIST platform, developed by Decisiv for Volvo and Mack Trucks. Link back to the ASIST case available in Vehicle History and the submission confirmation dialogs. Ability to Select New or Update existing case upon ASIST submission. Additional data is now sent to ASIST system including ECU Software Version. Ability to edit and correct mileage and VIN information upon data submission to ASIST service. NOTE: Installing the ASIST module will require personnel with ASIST Admin level access to provide ASIST Username and Password. NOTE: The ASIST module require either a heavy-duty or medium-duty module to be able to connect to vehicles. General Features Displays fault codes for all components on the supported data bus protocols. Displays manufacturer flash codes and descriptions for faults when available. Provides key data points in graphical displays for vehicle and components. Prints reports containing faults and key data. Automatically displays all component parameters of interest in the Data Monitor. o Search, sort or filter capabilities to easily identify parameters of interest. o Graph parameter changes over time. Automatically detects OEM applications and provides convenient methods to launch them. Diagnoses all vehicle components in a single application. Automatically connects to all supported and available data buses on the vehicle. Vehicle Readiness List displays information about each identified component. Troubleshooting information to help resolve issues connecting to a truck. Easy access to JPRO DLA+ Adapter Family test tools to aid in diagnosing connection problems. 9
Links to contact Noregon support or sales from within the application. Support for automatic updates. Ability to perform customized Preventative Maintenance Inspections. Inspection available in XML format as well as in PDF report format. Ability to configure the application to launch at computer startup. Demo mode in Vehicle History enables users to explore JPRO features quickly and easily without needing access to vehicles. Access to What s New document showing all supported features from the Connection Selection and Help menu. Ability to automatically switch between USB or Wireless when connecting with a DLA+ Wireless or DLA+ 2.0 Wireless adapter. Link to download ServiceMaxx and Bendix ACom diagnostic applications from OEM Application Portal. 10
Hardware / Software Configuration The following operating systems are supported: Windows 7 (both 32 and 64 bit versions) Windows 8 and 8.1 Pro (both 32 and 64 bit versions) Windows 10 (both 32 and 64 bit versions) Note: Spanish operating systems are supported. Notes 1) Registration is required before the JPRO Commercial Vehicle Diagnostics application can be used. Valid license key(s) will be required in order to register the application. Please ensure you have license key information available before you install. Registration over the internet is required; offline registration is not supported. 2) The appropriate vehicle adapter driver must be installed in order to connect to a vehicle adapter device. This installation is separate and independent of the JPRO Commercial Vehicle Diagnostics installation. 3) The vehicle adapter driver must be RP1210C compliant and support a minimum of 2 CAN Channels to be used with the JPRO Commercial Vehicle Diagnostics application. 4) The JPRO DLA+ 2.0, DLA+, DLA+ 2.0 Wireless or DLA+ Wireless adapters are required in order to connect to the Ford, GM, Isuzu or Sprinter Medium Duty vehicles. Please ensure you have the latest driver and firmware loaded. To connect to Ford use the OBDII Cable for Ford (red). To connect to GM use the OBDII Cable for GM (yellow). To connect to Sprinter use the OBD Cable for Sprinter (blue for DLA+ adapter family or gray for DLA+ 2.0 adapter family). To connect to Isuzu use the Generic OBD Cable (blue or gray) 5) The JPRO Heavy-Duty Command Module - Mack and Volvo only supports the following adapters: Noregon DLA+ 2.0, DLA+, DLA+ 2.0 Wireless, DLA+ Wireless and DLA+ PLC Vocom 88890300 NEXIQ USB-Link NEXIQ USB-Link 2 11