Table of Contents Accumulators RECEIVER DRIERS Basic Information Receiver Driers, Accumulators and In-Line Filters are canisters used to filter debris and remove moisture to protect the a/c system. Various inlet and outlet fitting types and sizes are used. Many also have system protection devices, moisture indicators, charge ports, sight glass, fuse plugs, high pressure relief valves, mounting brackets depending on the requirements from the original equipment manufacturer. Receiver Driers are usually located on the high side of the a/c system before the expansion valve. The receiver drier receives liquid refrigerant from the condenser, stores it, filters out contaminates from the a/c system, and removes moisture. A/C systems using a receiver drier use an expansion valve to control the refrigerant flow. Accumulators are similar to that of the receiver drier. It is usually mounted on the low side, at the outlet of the evaporator. The accumulator accumulates or stores excess refrigerant, filters and dries the refrigerant. Accumulators are used on CCOT (Cycling Clutch Orifice Tube) or FFOT (Ford Fixed Orifice Tube) systems. These systems use a orifice tube instead of an expansion valve to control the refrigerant flow. In-Line Filters are designed to be used in the liquid line in a/c systems with the orifice tube located in the evaporator. Placing the in-line filter up stream of the orifice eliminates the need to flush most systems, because the impurities are trapped before they reach the orifice tube. These filters are designed to hold up to 90 grams of debris, without a substantial penalty to the system s flow. The screens and filter pads inside the canister, catch particles and filters the refrigerant oil. NOTE Filter Drier manufacturers have discontinued using moisture indicators. We will supply moisture indicators where applicable while supply lasts. ACCUMULATORS Specification Chart...488 Typical Accumulator System CCOT...489 Visual Numerical Section...490 DRIER MEASUREMENTS RECEIVER DRIERS Specification Charts: Block, Manifold, Pad or Slimline Type...471 Flare Type...475 In-Line Filters...475 O-Ring Various Outlet Types...471 Quick Disconnect Type...474 Typical Drier System...476 Visual Numerical Section...477 LENGTH DIAMETER RELATED S Drier Brackets...496 s...496 Quick Disconnect Couplers...496 469
RECEIVER DRIERS can be harmful to air conditioning systems components and to the a/c system s operation. For this reason, any time the a/c system is opened, the receiver drier / accumulator needs to be replaced. A good preventative maintenance practice is to replace the receiver drier or the accumulator and orifice tube at regular intervals or at least once per year. When replacing a compressor, the a/c compressor manufacturer s warranty will be void without proof of flushing the system, and also replacement of the receiver drier. - a litmus paper device which turns colors to designate condition of the refrigerant. Blue - Normal, Pink - in system, White - Very Wet, Grayish - oil contamination. Manufactures have discontinued using moisture indicators. We will supply until stock is exhausted. / - A protection device designed to open and bleed off excessive pressure that may occur. The is a bi-metal device which will melt down to release excess pressure. glass - a window for observing the condition of the refrigerant. - a gauge or charge port which allows access to the system, for charging or checking the pressures. - Low / High es - a switch port allows for a male or female pressure switch to be added to the drier. If low charge is detected, the low pressure switch opens electronically and stops the compressor operation. Similarily, as pressure increases, the high pressure switch will dis-engage the clutch and re-engage when pressure normalizes. Typical Examples: indicator is not required and may not be supplied on drier. Low / High Charge/Gauge Quick Disconnect High (not required) Female O-Ring Type Charge/ Gauge High Quick Disconnect (not required) Charge/ Gauge Male O-Ring Type High Slimline Manifold - Block Type Male Flare Type (R12 only) Female Springlock Type Pad Type Male O-Ring Type Female O-Ring Type (some models) Male Springlock Type (some models) TECH TIP Metric uses green o-ring seals. 470
RECEIVER DRIERS Listed in ascending order by Diameter x Length by Fitting Type and Size. Block, Pad, Manifold, Slimline, or Springlock Style Fittings LET / LET DIA. LENGTH TYPE SIZE NOTE 1 5/8 11-5/8 Pad Type #6 use #790-1011 800-1004 Sprinter 680-013634AA 2 3/8 7 1/2 Pad Type - 800-1368 Volvo Exv EC Series, 14509377 R134a 2 3/8 9 Pad Type #6 800-1370 Top (2) Fem JD Excavator, 4448179;4646799 R134a 2.4 10 Pad Type 7mm use #790-1125 800-1366 CAT 176-1902 2 1/2 7 Pad Type #6 use #790-1011 800-1350 Caterpillar 113-3497 2 1/2 10 PadType #6 use #790-1011 800-1354 CAT 176-1902; Komatsu 20Y-979-320 2 3/4 10 Pad Type - 800-1362 Mitsubishi Fuso 2.9 9 Pad Type #6 use #790-1011 800-1358 M10 3/8-24 port; Linkbelt YT54500003P1 3 10 Slimline #6 #6 use #790-1326 800-1205 (2) M10 Top N83-319744 3 10 1/4 Slimline #6 #6 use #790-1326 800-1208 (2) M10 Top N83-319534 3 10 1/2 Pad /Block use #790-1402 800-1304 16mm Off-Road Volvo 11104567 3 11 Manifold #6 use #790-1011 800-1105 Kenworth F37-6000 3 11 Pad Manifold - 800-1106 Peterbilt F37-6002 3 11 Pad Manifold - 800-1107 Peterbilt F37-6008 3 11 Pad Manifold - 800-1108 Peterbilt F37-6009 3 14.35 Springlock #6 use #790-1111 800-1404 Side Ford New Holland 4 7 Block Style #8 use #790-1331 800-1215 A22-63992-000, -001 4 7 Block Style #8 use #790-1331 800-1216 Frghtlnr A22-63994-001 4 7 Pad Type #8 use #790-1331 800-1220 A22-63993-001, A22-65550-000 - - Pad Type GM#8 #790-1210 800-1008 Sprinter Van 2.7L, 051-03570AA 2 1/2 Diameter - 3/8 or M18 Male O-Ring LET w/various Outlets DIA. LENGTH LET LET NOTE 2 1/2 5.9 3/8 #6 3/8 #6 800-1704 Top 3/8 Side 3/8 O ring port; 085428-00 2 1/2 6 5/16 3/8 #6 Course Thread 800-1708 Top (1) M10 33-0038A 2 1/2 6 5/16 M18 Fine Thread 800-1712 Top (1) M10 33-0382A 2 1/2 6 5/16 M18 M18 800-1720 Top (1) M10 33-0383A 2 1/2 6 5/16 M18 Fine Thread 800-1716 Top (1) M10 Motorhome 085686-00 2 1/2 6.32 M18 M18 800-1724 Top (1) M10 RV218337, 085722 2 1/2 6 3/4 3/8 #6 MOR 1/2 #8 800-2704 In-Line Design, GMC 2 1/2 6 3/4 M18 MOR M20 800-2708 In-Line Drier; 15982368 2 1/2 8 3/8 #6 3/8 #6 800-1505 Top (2) Top 085268-03 (new style) 2 1/2 8 3/8 #6 3/8 #6 800-1512 Top 1/4 Male Top uses #910-1038 switch 2 1/2 8 1/4 3/8 #6 3/8 #6 800-1504 Top Top Bracket 2 1/2 10 3/8 #6 3/8 #6 800-2716 RD remote condenser - - 3/8 #6 MIO 800-2395 Volvo #20490945 Low 471
RECEIVER DRIERS Listed in ascending order by Diameter x Length by Fitting Type and Size. 2 Diameter - 3/8 Male O-Ring LET x 3/8 Male O-Ring LET DIA. LENGTH LET LET NOTE Low 2 1/2 8 3/8 #6 3/8 #6 800-2006 Top Side Side Thermo King Tri-Pac #61-3552, R134a 2 3/4 10 3/8 #6 3/8 #6 800-1804 Top Side 2 3/4 10 3/8 #6 3/8 #6 800-1805 Top 1/4 Side Side Mack 221RD328 2 3/4 10 3/8 #6 3/8 #6 800-1812 Top Side Side 2 3/4 10 3/8 #6 3/8 #6 800-1813 Top w/ Trinary - #923-1106 2 3/4 10 3/8 #6 3/8 #6 800-1816 Side Top Side Kenworth K251-263 2 3/4 10 3/8 #6 3/8 #6 800-1820 Side Top Side IHC1691600C92 2 3/4 10 3/8 #6 3/8 #6 800-1824 Side Top Side w/ Trinary - Top 2.6 11 3/8 3/8 MIO 3/8 MIO 800-1904 Side (2) female ports; Hino Truck 2.6 11 3/8 790-1125 790-1125 800-1908 (2) fem Hino Truck, metric 14mm, R12/R134a 3 Diameter - 3/8 Male O-Ring LET x 3/8 Male O-Ring LET DIA. LENGTH LET LET NOTE 3 6 3/8 #6 3/8 #6 800-2004 Top Side Side 3 6 1/4 3/8 #6 3/8 #6 800-3212 Side Side 3 6 1/4 3/8 #6 3/8 #6 800-2028 Top Female Side Terex Loader SKL863, SKL873,R134a 3 6 3/8 #6 3/8 #6 800-2016 Top Side 3 6 1/2 3/8 #6 3/8 #6 800-2022 Top Side Top Side Red Dot RD5-7272-0 3 6 1/2 3/8 #6 3/8 #6 800-2025 Top 1/4 Side Side 088423-00; 01 3 6 1/2 3/8 #6 3/8 #6 800-2034 Top Side Binary (Side) 3 6 1/2 3/8 #6 3/8 #6 800-2040 Top Side Trinary (Side) 3 6 1/2 3/8 #6 3/8 #6 800-2046 Top Top Side N83-319634; RD5-9419-0 3 8 3/8 #6 3/8 #6 800-2054 (2) 1/4 3 8 1/4 3/8 #6 3/8 #6 800-2060 Top Top Side 3 8 1/4 3/8 #6 3/8 #6 800-2066 Side Top 3 8 1/4 3/8 #6 3/8 #6 800-2072 Top Side 1/4 Side Top 3 8 1/2 3/8 #6 3/8 #6 800-2078 Top Female Side Side 3 8 3/8 #6 3/8 #6 800-2084 Top (2) (2) M10 x 1.25mm 3 9 3/8 #6 3/8 #6 800-2095 Top 1/4 Top Top Side 3 9 3/8 #6 3/8 #6 800-2096 Top Side Top Side 1/8-27NPT ; 088254-01 3 9 3/8 #6 3/8 #6 800-2104 Top Side 20407203 3 9 3/8 #6 3/8 #6 800-2110 Top Top Inlet - Right Angle 3 9 3/4 3/8 #6 3/8 #6 800-2116 Top w/side mounting bracket 3 10 3/8 #6 3/8 #6 800-2122 Top Side 1/4 Side Top Western Star 3 10 3/8 #6 3/8 #6 800-2128 Side Side Top Top 3 10 3/8 #6 3/8 #6 800-2134 Top Top Top Side 3 10 3/8 #6 3/8 #6 800-2140 Top 1/4 Top Top Top 3 10 3/8 #6 3/8 #6 800-2145 Top M10 Top Top Top M10 x 1.25mm 3 10 3/8 #6 3/8 #6 800-2152 Side 1/4 fem Side 088079-00; 176237; K251-459 3 10 3/8 #6 3/8 #6 800-2158 Top w/side mounting bracket 3 10 3/8 #6 3/8 #6 800-2164 Top Top w/side mounting bracket 3 10 3/8 #6 3/8 #6 800-2170 Top w/side & top mntg brkts 3 10 3/8 #6 3/8 #6 800-2176 Western Star 088586-00 3 10 1/2 3/8 MIO 3/8 MIO 800-5200 Side (3) 1/4 Volvo Offroad 1089855, R134a - - - - 800-5201 J.Deere 582166227, R134a Low 472
Listed in ascending order by Diameter x Length by Fitting Type and Size. 3 Diameter 3/8 Male O Ring LET x 1/2 Male O Ring LET RECEIVER DRIERS DIA. LENGTH LET LET Note 3 6 1/2 3/8 #6 3/8 #6 800-2031 Male CAT Exv., M318 / FNH EC270 Low 4 Diameter - 3/8 Male O-Ring LET x 3/8 Male O-Ring LET DIA. LENGTH LET LET NOTE 4 6 1/2 3/8 #6 3/8 #6 800-5004 Top w/mounting bracket 4 6 3/4 3/8 #6 3/8 #6 800-5008 Side Side Volvo RD5-6075-0 4 7 3/8 #6 3/8 #6 800-5016 Top Side Top Opposite Side Inlet 4 7 #6 Flare #6 Flare 800-5608 Top Side w/ 4 7 3/4 3/8 #6 3/8 #6 800-5020 Top Top Side Side 4 8 1/2 3/8 #6 3/8 #6 800-5024 Top Side Top Top CAT# 5V5698; 8P9991 Low 3/8 Male O-Ring LET x 3/8 Female O-Ring LET 3 8 3/8 #6 3/8 #6 800-2204 Top (2) 1/4 Side 3 8 3/8 #6 3/8 #6 800-2208 Top (2) M10 Top Side (M10 x 1.25mm) 3 8 1/4 3/8 #6 3/8 #6 800-2212 Top (2) 1/4 Top Top R12, Peterbilt 18-03638 3 10 3/8 #6 3/8 #6 800-2216 Top (2) 1/4 Side 3 10 3/8 #6 3/8 #6 800-2225 Top (2) M10 Top 4 7 3/4 3/8 #6 3/8 #6 800-5104 DIA. LENGTH LET LET NOTE 3/8 Female O-Ring LET x 3/8 Male O-Ring LET Low DIA. LENGTH LET LET NOTE 3 10 3/8 #6 3/8 #6 800-2325 Side Top K251-459,K251-571 3 10 - - 800-5202 Top Ford New Holland, 82012480 3 11 1/2 3/8 #6 #6 MIO 800-5204 JDeere, RE214440 3 11 1/2 3/8 #6 #6 MIO 800-5208 JDeere, AL163559 w/bracket 4 7 3/8 #6 #6 MIO 800-5304 JDeere, AL162467 w/bracket 4 7 3/8 #6 3/8 #6 800-5308 Top Side 4 7 1/2 3/8 #6 3/8 #6 800-5404 (2) Side 4 7 1/2 3/8-18 3/8 #6 800-5408 (2) Side John Deere RE49169 4 7 3/4 3/8 #6 #6 MIO 800-5312 CASE, 86984155 4 8 1/2 3/8 #6 3/8 #6 800-5318 JDeere AZ45582 R12/R134a 4 8 3/4 3/8 #6 3/8 #6 800-5316 Side/Top Top JDeere AT162848; AT151981 Low 473
RECEIVER DRIERS Listed in ascending order by Diameter x Length by Fitting Type and Size. 3/8 Female O-Ring LET x 3/8 Female O-Ring LET Dia. LENGTH LET LET NOTE 3 10 7/16 #6 3/8 #6 800-2404 Top Top Top Side 3/16 Charge 3 10 11/16 #6 3/8 #6 800-2408 Top Top Top 3 10 11/16 #6 3/8 #6 800-2415 Top 16mm Top ParkerType; IHC 1693117C1 4 9 3/8 #6 3/8 #6 800-5504 R12, Ford E2NN-19825AA Low NOTE Filter Drier manufacturers have discontinued using moisture indicators. Quick Disconnect Type DIA. LENGTH LET LET NOTE 2 1/2 6 QD QD 800-2504 In-Line; Peterbilt 18-03841 2 1/2 6 QD QD 800-2604 Top (1) M10 (1) M10 x 1.25mm - Top 2 1/2 6 5/16 3/8 #6 Course Thrd 800-1708 Top (1) M10 (1) Top M10 Male 2 1/2 6 5/16 M18 Fine Thrd 800-1712 Top (1) M10 (1) M10; 33-0382A 2 1/2 6 5/16 M18 M18 800-1720 Top (1) M10 (1) M10; 33-0383A 2 1/2 6 5/16 M18 Fine Thrd 800-1716 Top (1) M10 Motorhome 085686-00 2 1/2 7 3/4 QD QD 800-5605 Side Incl. orifice tube; CAT3E3535 3 9 5/8 QD side QD 60mm 800-2608 Top (2) M10 ABP N83 319524; 088470-01 3 10 QD QD 800-2612 Top (2) 1/4 Top Top 2 Vlvs (1/4 Top) 3 10 QD QD 800-2615 Top (2) M10 (2) M10 x 1.25mm (Top) 3 10 QD QD 800-2620 Top 16mm Top Side R134a Service 3 10 QD QD 800-2624 Side Top 4 8 1/2 QD QD 800-5608 Top Top Side Side Low 474
RECEIVER DRIERS Listed in ascending order by Diameter x Length by Fitting Type and Size. In-Line Filters / Driers 2 1/2 6 QD QD 800-2504 In-Line Drier; Peterbilt 18-03841 2 1/2 6 3/4 3/8 #6 Male Flare 3/8 #6 Male Flare 800-3004 In-Line Drier WAH 163; 16cu.in. 2 1/2 6 3/4 3/8 #6 Male O Ring 1/2 #8 Male O Ring 800-2704 In-Line Design,GMC 2 1/2 6 3/4 M18 Male O Ring M20 Male O Ring 800-2708 In-Line Drier; GMC 15982368 2 1/2 7 1/2 Flare 1/2 Flare 800-3008 In-Line Drier; WLD164FO; 16cu.in. 2 1/2 7 1/2 Flare 1/2 Flare 800-3012 In-Line Drier; WAH164; 16cu.in. 2 1/2 7 3/4 QD QD 800-5605 Enclosed Orifice; CAT# 3E3535 2 1/2 7 3/4 MIO Fitting MIO Fitting 800-2712 w/orifice Tube, CAT# 257-3227 2 1/2 10 3/8 Male O Ring 3/8 Male O Ring 800-2716 In-Line Drier, RD remote cond. 2 5/8 7 1/2 3/8 #6 Male 3/8 #6 Female 800-2720 Side 16 cu.in. dessicant; Kysor 402618 2 3/4 8 1/2 1/2 Flare 1/2 Flare 800-3016 Side In-Line Drier WSG164FO; 16cu.in 2 3/4 8 1/2 1/2 #8 MIO 1/2 #8 MIO 800-3020 Side In-Line Retro; Carrier A/C; 16cu.in. 3 10 1/2 SAE 1/2 SAE 800-3024 Side In-Line, Carrier WSG304; 30cu.in 3 10 1/2 Flare 1/2 Flare 800-3040 In-Line, EK304; 212-010; 30cu.in. 3 10 1/2 3/8 #6 Male 3/8 #6 Female 800-5314 Side FNH Backhoe 555E-685E; 85804063 3 10 1/2 5/8 SAE 5/8 SAE 800-3044 In-Line, Carrier WAH305; 30cu.in. 3 11 1/2 1/2 #8 MIO 1/2 #8 MIO 800-3048 Side In-Line, Carrier ADK304; 30cu.in. 3 3/4 10 3/4 1/2 Flare 1/2 Flare 800-3052 In-Line, TransAir AH414; 41cu.in. 4 7 1/2 3/8 Female O Ring 3/8-18 Male O Ring 800-5408 (2) Side In-Line Drier JDeere RE49169 DIA. LENGTH LET LET NOTE NOTE Filter Drier manufacturers have discontinued using moisture indicators. Flare End Fittings - Male LET and Male LET DIA. LENGTH LET LET NOTE 2 1/2 6 3/4 #6 Flare #6 Flare 800-3004 In-Line; 16cu.in.; WAH163 2 1/2 7 1/2 Flare 1/2 Flare 800-3008 In-Line ; WLD164FO; 16cu.in. 2 1/2 8 #6 Flare #6 Flare 800-3204 Top 2 1/2 8 #6 Flare #6 Flare 800-3208 Top Top Top w/low Sw. 3 6 1/4 #6 Flare #6 Flare 800-3212 Top Side w/ 3 10 1/2 Flare 1/2 Flare 800-3040 In-Line; 30cu.in.; EK304 4 7 3/4 #6 Flare #6 Flare 800-5604 Top Side R12, w/ 4 7 #6 Flare #6 Flare 800-5608 Side Side w/ Low 475
RECEIVER DRIERS Typical Drier System Compressor Expansion Drier Evaporator Condenser Thermostat 476
NOTE: Drier mfg s have discontinued using moisture indicators. 800-1004 - Diameter:... 1-5/8 - Length:... 11-5/8 - Pad Style Drier - Sprinter Van - OE#: 680-013634AA #790-1011 800-1008 - Pad Style Drier - Sprinter Van - OE#: 051-03570AA #790-1210 RECEIVER DRIERS #6 = 3/8 #8 = 1/2 #10 = 5/8 #12 = 3/4 800-1105 - Length:... 11 - Pad Manifold Fittings - Kenworth T2000 - OE#: F37-6000 - R134a Only #790-1011 800-1106 - Length:... 11 - Pad Manifold Fittings - 330, 340, 387 Series - Peterbilt - OE#: F37-6002 800-1107 - Length:... 11 - Pad Manifold Fittings - 365 thru 389 Series - Peterbilt - OE#: F37-6008 800-1108 - Length:... 11 - Pad Manifold Fittings - Peterbilt - OE#: F37-6009 800-1205 - In/Out: #6 Slimline - M10 s (2) - Relief - OE#: ABPN83-319744 #790-1326 seals 800-1208 - Length:... 10-1/4 - M10 s (2) - OE#; ABPN83-319534 - R134a Only #790-1326 seals 800-1215 - In/Out:... #8 Stat Seals - Freightliner Columbia M2 - OE#: A22-63992-000; A22-63992-001 #790-1331 stat seals 800-1216 - In/Out:... #8 Stat Seals - Freightliner Coronado - OE#: A22-63994-001 #790-1331 stat seals 800-1220 - In/Out:... #8 Stat Seals - Freightliner - OE#: A22-63993-001; A22-65550-000 #790-1331 stat seals 800-1304 - Length:... 10-1/2 - Pad Type Drier - with 16mm - Volvo Off Road - OE#: 11104567 #790-1402 477
RECEIVER DRIERS NOTE: Drier mfg s have discontinued using moisture indicators. 800-1350 - Pad Type Drier - Caterpillar - OE#: 113-3497 #790-1011 800-1354 - Pad Type Drier - Kubota OE#: 3F999-10740 - Komatsu OE#: 20Y-979-320 #790-1011 #6 = 3/8 #8 = 1/2 #10 = 5/8 #12 = 3/4 800-1358 - Diameter:... 2.9 - Length:... 9 - Pad Type Drier - 3/8-24 ; M10 - Linkbelt Excavator - OE#: YT54500003P1 #790-1125 3/8-24 800-1362 - Pad Type Drier - 12.45mm s (2) - Mitsubishi Fuso 800-1366 - Diameter:... 2.4 - Pad Type Drier - Caterpillar - OE#: 176-1902 M10 3/8-24 800-1368 - Pad Mount Drier - Diameter:... 2-3/8 - Length:... 7-1/2 - VOLVO Excavators, EC Series - OE# 14509377 #790-1125 12.45mm 12.45mm 800-1370 - Pad Mount Drier - Diameter:... 2-3/8 - Length:... 9 - (2) 3/8 x 24 Female Sw s - J Deere Excavators - OE# 4448179; 464699 800-1404 - Length:... 14.35 - #6 Spring Lock - Ford New Holland - OE#: 89154-00 800-1504 - Length:... 8-1/4-800-1505 - Length:... 8 - Female - 1/4 Male - OE#: A22-14425-2; 085268-03 800-1512 - Length:... 8-1/4 Male - Low 800-1704 - Length:... 5.9 - Side ; 3/8 - OE#: 085428-00 #790-1011 #910-1038 switch 478
RECEIVER DRIERS NOTE: Drier mfg s have discontinued using moisture indicators. #6 = 3/8 #8 = 1/2 800-1708 800-1712 - Length:... 6-5/16 - In: 3/8 Male O-ring - Out: 1/2-20 Course Thread - M10 (1) -Top. - OE#: 33-0038A #10 = 5/8 #12 = 3/4 800-1716 - Length:... 6-5/16 - In: M18 Male - Out: Fine Thread - M10 (1) - OE#: 33-0382A; 088370-0 - Length:... 6-5/16 - In: M18 Male - Out: Fine Thread - M10 - GM Chasis Motor Home - OE#: 085686-00 #790-1011 course thread check valve fine thread check valve 800-1724 800-1720 800-1804 - Length:... 6.32 - In/Out: M18 Male - M10 - OE#: 085722; RV218337 - Length:... 6-5/16 - In/Out: M18 Male - M10 (1) - OE#: 33-0383A; 088371-00 fine thread check valve - Side Low 800-1805 800-1812 - Side 1/4 - Mack OE#: 221RD328 - Side Trinary #923-1106 switch 800-1813 - Side 800-1816 800-1820 - Side - Top - Kenworth OE#: K251-263 800-1824 - Side - Top - IHC OE#: 1691600C92 - Side - Top Trinary 479
RECEIVER DRIERS NOTE: Drier mfg s have discontinued using moisture indicators. #6 = 3/8 #8 = 1/2 #10 = 5/8 #12 = 3/4 800-1904 - Diameter:... 2.6 - Length:... 11-3/8 - In/Out:... 3/8 x 3/8 - Male Insert O ring - Female s (2) - Hino Trucks female port 800-1908 - Diameter:... 2.6 - Length:... 11-3/8 - In/Out: 14mm METRIC - Female s (2) - Hino Trucks female port 800-2004 - Length:... 6 - Side - High Press Reliev Vlv female port female port 800-2006 - Length:... 8 Male -, - 1/4 NPT Ftg - Thermo King Tri-Pac Unit - OE# 61-3552 800-2016 - Length:... 6-800-2022 - Length:... 6-1/2 - Side 1/4 NPT 800-2025 - Length:... 6-1/2 - Side 1/4 - High Press 800-2028 - Length:... 6-1/4 - Female - TEREX Wheel Loader - SKL863, SKL873 800-2031 - Length:... 6-1/2 - In: #6 Male O-ring - Out: #6 Male O-ring - Male - CAT Exv., M318 - FNH Excavator EC270 - OE# 73186213 800-2034 - Length:... 6-1/2 - Side Binary - 800-2040 - Length:... 6-1/2 - Side Trinary - 800-2046 - Length:... 6-1/2 - OE#: RD5-9419-0 480
RECEIVER DRIERS NOTE: Drier mfg s have discontinued using moisture indicators. #6 = 3/8 #8 = 1/2 800-2054 800-2060 - Length:... 8 - s (2) 800-2072 800-2095 800-2110 - Length:... 9 - Inlet: Right Angle - 3/8 x 3/8 Male O-ring - Length:... 9 - OE#: 20407203 800-2116 -, 1/4 (1) - Western Star 800-2122 - Length:... 9 3/4-800-2104 - Length:... 9 - Side (1/8-27 NPT) - PRV; - OE#: 088254-01 - Length:... 8 - M10 Vlvs(2) - OE#: PH088340-01 800-2096 - Length:... 9 - Top 800-2084 - Length:... 8-1/2 - Male - Female - Length:... 8-1/4 - Side - Top 800-2078 - Length:... 8-1/4 - - #12 = 3/4 800-2066 - Length:... 8-1/4 - Top #10 = 5/8 481
RECEIVER DRIERS NOTE: Drier mfg s have discontinued using moisture indicators. #6 = 3/8 #8 = 1/2 800-2128 800-2134 - Side - Top - - Length:... 8 - In: 3/8 Male O-ring - Out: 3/8 Female O-ring - s (2) 482 800-2158 - Volvo Construction A25B - OE#: 11005931 800-2208 - Length:... 8 - In: 3/8 Male O-ring - Out: 3/8 Female O-ring - M10 Vlvs (2) 800-2196 - Western Star - OE#: 088586-00 800-2204 800-2176 - Side - 1/4 Female - High - Kenworth OE#: K251-459 800-2164 800-2152 - METRIC, M10 Vlv - 800-2145 800-2140 - Top #10 = 5/8 800-2212 - Diameter:... 3 - Length:... 8-1/4 - In: 3/8 Male O ring - Out: 3/8 Female O ring - s (2) - High Relief Vlv - R12 Only #12 = 3/4
NOTE: Drier mfg s have discontinued using moisture indicators. 800-2216 - In: 3/8 Male O-ring - Out: 3/8 Female O-ring - s (2) - OE#: ABPN83-319714 800-2225 - In: 3/8 Male O-ring - Out: 3/8 Female O-ring - M10 Vlvs (2) RECEIVER DRIERS #6 = 3/8 #8 = 1/2 #10 = 5/8 #12 = 3/4 800-2325 - In: 3/8 Female O-ring - Out: 3/8 Male O-ring - Side - Kenworth - OE#: K251-571 800-2395 - Male Insert O ring - R134a - Volvo Loader - OE#: 20490945 800-2404 - In: 7/16 Female O-ring - Out: 3/8 Female O-ring - Charge 3/16 - PRV; 800-2408 - In: 11/16 Female O-ring - Out - 3/8 Female O-ring R134a 800-2415 - In: 11/16 Female O-ring - Out - 3/8 Female O-ring ; PRV - 16mm Service - R134a Only 800-2504 In-Line Drier - R134a Only - Length:... 6 (9.6 overall) - Quick Disconnect - Peterbilt - OE#: 18-03841 800-2604 - Length:... 6 - Quick Disconnect - M10 800-2608 - Length:... 9 5/8 - Quick Disconnect - 60mm (2 3/8 ) - In: QD (side) - Out: QD (top) - M10 s (2) - - OE#: ABPN83-319524; - 088470-01 800-2612 - Quick Disconnect - 1/4 s (2) - High - R134a Only 800-2615 - Quick Disconnect - M10 s (2) - R134a Only 483
RECEIVER DRIERS NOTE: Drier mfg s have discontinued using moisture indicators. 800-2620 - Quick Disconnect - R134a Service, 16mm 800-2624 - Quick Disconnect - Side - R134a Only #6 = 3/8 #8 = 1/2 #10 = 5/8 #12 = 3/4 800-2704 - Length:... 6-3/4 - In-line Design - In: 3/8 Male O-ring - Out: 1/2 Male O-ring - GMC (In-line design) 800-2708 - Length:... 6-3/4 - In-line Design - In: M18 Male O-ring - Out: M20 Male O-ring - GMC OE#: 15982368 800-2712 - Length:... 7-3/4 (13.88 OAL) - MIO fittings with orifice tube - CAT OE#257-3227 800-2716 - Red Dot remote condenser # 790-1177 800-2720 - Diameter:... 2-5/8 - Length:... 7-1/2 - In: 3/8 #6 Male O-ring - Out: 3/8 #6 Female O-ring - 16 cu. in. dessicant In-Line Drier - Relief Vavle - Kysor OE#: 402618 800-3004 - Length:... 6-3/4 - Male Flare - 16 cu.in. In-Line Filter Drier - OE#: WAH163 800-3008 - In/Out: 1/2 x 1/2 Male Flare - 16 cu.in. In-Line Filter Drier - OE#: WAH164FO # 790-1270 (not supplied) 800-3012 - In/Out: 1/2 x 1/2 - Male Flare - 16 cu. in. In-Line Drier - OE#: WAH 164 800-3016 - Length:... 8-1/2 - In/Out: 1/2 x 1/2 Flare O-ring - 16 cu.in.in-line Drier w/sight glass - OE#: WSG164 FO 800-3020 - Length:... 8-1/2 - In/Out: 1/2 x 1/2 Male Insert O-ring - 16 cu.in. In-Line Drier w/sight glass - CARRIER OE#: 14-00288-00; - WSG 164 MIO #790-1270 (not supplied) #790-1013 484
NOTE: Drier mfg s have discontinued using moisture indicators. 800-3024 - 30 cu. in. In-Line Drier w/sight glass - In/Out: 1/2 SAE - Carrier WSG304 800-3040 - In/Out: 1/2 x 1/2 Male Flare - 30 cu.in. In-Line Filter Drier - OE#: EK304 RECEIVER DRIERS #6 = 3/8 #8 = 1/2 #10 = 5/8 #12 = 3/4 800-3044 - Length:... 10-1/2 - In/Out: 5/8 SAE - 30 cu. in. In-line Filter Drier - Carrier WAH305 800-3048 - Length:... 11-1/2 - In/Out: 1/2 Male Insert O-ring - 30 cu. in. In-line Filter Drier w/sight glass - Carrier - OE#: ADK304; WSG304MOI #790-1013 800-3052 - Diameter:... 3-3/4 - Length:... 10-3/4 - In/Out: 1/2 Male Flare - 41 ci.in. dessicant - TYPE AH414 In-LineDrier - TransAir A/C 800-3054 - Side - Bottom High Press Sw - Top - Carrier - OE#: 65-00193-00; 088599-01 800-3204 - Length:... 8 - In/Out: 3/8 Male Flare 800-3208 - Length:... 8 - In/Out: 3/8 Male Flare - Top - Low 800-3212 - Length:... 6-1/4 - In/Out: 3/8 Male Flare - 800-5004 - Length:... 6-1/2 800-5008 - Length:... 6-3/4 - In/Out: 3/8 Male O ring - Side - Side - Volvo Off Road - OE#: RD5-6075-0 800-5016 (opposite side inlet) - Side 485
RECEIVER DRIERS NOTE: Drier mfg s have discontinued using moisture indicators. 800-5020 - Length:... 7-3/4 - Side Low Sw - R134a Only 800-5024 - Length:... 8-1/2 - In/Out: 3/8 MIO - Low Sw - Sided - Combo: & - CAT 5V5698; 8P9991 #6 = 3/8 #8 = 1/2 #10 = 5/8 #12 = 3/4 800-5104 - Length:... 7-3/4 - In: 3/8 Male O-ring - Out: 3/8 Female O-ring 800-5202 - Ford / New Holland - OE#: 803-380; 82012480 800-5204 - Length:... 11-1/2 - In: #6 Female O-ring - Out: #6 Male Insert O-ring - J. DEERE - OE#: RE214440; 088545-00 800-5208 - Length:... 11-1/2 - In: #6 Female O-ring - Out: #6 Male Insert O-ring - J. DEERE - OE#: AL163559; 088549-00 800-5304 - In: #6 Female O ring - Out: #6 Male Insert O-ring - J. DEERE - OE#: AL162467 800-5308 - In: 3/8 Female O-ring - Out: 3/8 Male O-ring - Side 800-5312 - Length:... 7-3/4 - In: #6 Female O-ring - Out: #6 Male Insert O-ring - CASE TRACTOR - OE#: 86984155 800-5314 - Length:... 10-1/2 - In: #6 Male O ring - Out: #6 Female O ring -, 7/16 Male Flare - Side - Top Mount Bracket - FNH Backhole 555E-675E - OE# 85804063 800-5316 - Length:... 8-3/4 - In: 3/8 Female O-ring - Out: 3/8 Male O-ring - Top & Side - J. DEERE AT151981; AT162848 800-5318 - Length:... 8-1/2 - In: 3/8 Female O-ring - Out: 3/8 Male O-ring - Combines, Telehandlers - Forage Harvesters - OE# AZ45582 486
NOTE: Drier mfg s have discontinued using moisture indicators. 800-5404 - Length:... 7-1/2 - In: 3/8 Female O-ring - Out: 3/8 Male O-ring - Side (2) 800-5408 - Length:... 7-1/2 - In: 3/8 Female O-ring - Out: 3/8-18 Male O-ring - Side (2) - J. DEERE - OE#: RE49169 RECEIVER DRIERS #6 = 3/8 #8 = 1/2 #10 = 5/8 #12 = 3/4 800-5504 - Length:... 6 - Horizontal Type - In: 3/8 Female Piloted O-ring Fitting - Out: 3/8 Female Piloted O-ring Fitting 800-5604 - Length:... 7-3/4 - In/Out: 3/8 Male Flare - - R12 Only 800-5608 - Male Flare - 800-5705 - Length:... 7-3/4 (13.88 OAL) - Quick Disconnect - Enclosed Orifice Tube - CAT OE#: 3E3535 - R134a Only 800-5708 - Length:... 8-1/2 - Quick Disconnect - Low Press Sw. - PRV - R134a Only 800-5200 - Length:... 10-1/2 - #6 x #6 MIO - 1/4 Male (1) - 1/4 Female s (2) - Side - Volvo Offroad - OE#: 1089855 800-5201 - Drier - J.Deere / Liebherr / Terex - OE#: 5821662227 487