JLI exhaust hood
PAGE Table of Contents Product description & Product code Functioning principle, Parts Dimensions Positioning, Design Service Exhaust air 7 Pressure loss & Sound data, Lights 8 We want to help you in design of ventilation by offering Jeven designer service to your disposal. Design Service helps in design and makes unique proposal solution with Jeven products. Contact us: jeven@jeven.fi 00 00
PRODUCT DESCRIPTION The Jeven JLI hood has been designed for light duty kitchens where exhaust-only hoods are needed or supply air units are impossible to install. JLI hoods are equipped with filter units, damper plates and measurement taps. JLI is equipped with special filter units, which are easy to wash in a dishwasher. LIGHTS AND FILTERS All Jeven hoods come equipped with lights. Standard JLI hoods are equipped with cyclonic JCE grease filters. MATERIAL The canopy s base material is stainless steel AISI 0. The side panels can be made of stainless steel (JLI-R) or laminated glass (JLI-S). ACCESSORIES Covering boards to enclose the area between the top of the hood and the ceiling. PRODUCT CODE JLI - R 000 x 00 x 0 - x - 080 m/h - CB Seinämateriaali R= Stainless steel S= Glass Length Width Height Number and size of the exhaust air connections Exhaust air flow, m/h Accessories CB=Covering boards PAGE
PAGE FUNCTIONING PRINCIPLE. Heat and impurities rise into the hood.. Grease particles are removed in the filter. Clean air is exhausted. PARTS. Outer casing. Light fixture with a cable. Grease filters and measurement tap for exhaust air. Exhaust air connection and damper plate. Ceiling console. Hanging bracket
SIVU DIMENSIONS Island type hood Wall hood A xw Module JCE B JCE xw Module Module Module xw xw width width B Y A A JCE JCE A (module) length xw xw length Y-Y 7 height height 7 width width Hoods length, width and A, B-dimensions can be chosen freely. Max. module size is 000mm x 800mm. Filters require 0 mm of free space to open. Y (module) A-A
PAGE POSITIONING X 00-00 The size of the canopy is determined by the size of the kitchen equipment. The overhang depends on the type of equipment and the distance between the hood and the equipment. For this type of equipment, the overhang should be at least 00 mm. The typical distance between the hood side and the floor is 00-00 mm. If the equipment has any doors that open upwards, make sure there is enough distance to the canopy. >0. *X >00 Oven DESIGN SERVICE Jeven Design Service helps you choose the best solution for your professional kitchen project. Simply email us a drawing of the kitchen lay-out and a list of the cooking equipment to jeven@jeven.fi We will do all the calculations and prepare all the necessary drawings of the canopies. This service is always free of charge to you.
EXHAUST AIR The recommended exhaust airflow rate is max. 0 l/s per mm spigot, with a duct velocity of. m/s. By default, the canopies come with a suitable number of filter units so that the pressure level will be between 0 and 0 Pa. The nominal airflow of the filter units is 0 l/s per filter module. GREASE FILTER EXTRACTION RATE Extraction rate( % ) 00 90 80 70 0 0 0 0 0 0 8 Particle size ( µm ) Pressure loss> 0 Pa Pressure loss> 00 Pa Recommended exhaust flow / spigot Spigot size ø mm 00 00 Exhaust flow l/s m/h 0-0 - 00 0-0 00-0 - 0-90 SIVU 7
PAGE 8 LIGHTS Pressure loss 80 70 0 0 db(a) =0 8 Ps (Pa) 0 00 Number of filter modules 78 0 PRESSURE LOSS AND SOUND DATA B db(a) =0 0 0 80 00 0 00 0 00 00 800 l/s 0 0 00 00 00 700 000 00 00 m³/h 800 Sound power level Lw in each octave band is computed by adding the corresponding factor, Kok to the sound power level LpA. Lw= LpA+Kok. Light fixture as standard IP -7 T8: B=mm, (x8w, xw, x8w) B=8mm, (x8w, xw, x8w) Colour temperature 80(Cool White) About m cable, type EKK x, Factor, Kok Hz Kok tol. ± 0 ± 00 000 000 000 - -9 - ± ± ± ± By default, every hood module comes with a light fixture. The light fixture has a cable which should be connected to a junction box with a cable lock. The junction box is not included. SOUND ATTENUATION Exhaust JCE-, spigot = ø 00 mm. Sound attenuation, (db) Hz Damper closed Damper open 0 7 00 000 000 000 7 0 0 0 0 00 000 000 000 0 0 7 Exhaust JCE-, spigot = ø mm. Sound attenuation, (db) Hz Damper closed Damper open 9..0 The average sound attenuation includes the end reflection of the connection spigot. It is recommended to use damper open values when calculating sound attenuation