1701 38TH AVE W PO BOX 257 SPENCER, IA 51301 PHONE: 712-262-4191 FAX: 712-262-0248 SERVICE: 800-841-2222 E-MAIL: ccac@cyclecountry.com www.cyclecountry.com ALLMount ATV Plow Mount Kit Model Number: 15-0050 Owner s Manual CUSTOMER MUST RECEIVE A COPY OF THIS OWNER S MANUAL AT TIME OF SALE 2009 Cycle Country Accessories Corp. 12/22/09 MAN0163
The Cycle County ALLMount is a universal mount to attach a Cycle Country Work Power 2000 Push Tube (Model No. 15-0001) to an ATV. The ALLMount attaches to the frame of the ATV with U-bolts and is adjustable to fit most ATVs (See application chart at www.cyclecountry.com). Warning! Do not exceed 5 mph with plow or ALLMount installed. Due to reduced ground clearance, remove ALLMount before trail riding. Periodically check for wear and tightness of all fasteners. Replace or tighten as necessary. Make sure not to pinch any wires, cables, hoses, or brake lines while installing the ALLMount. Do not fasten the ALLMount to any moving suspension parts. 10 7 12 11 9 14 13 15 1 3 2 8 Model Number 15-0050 Parts List 4 5 6 2 ITEM NO. QTY. PART NO. DESCRIPTION 1 1 CYC4104 Universal Mount Weldment 2 2 CYC4106 Mount Strap 3 2 PUR1176 Carriage Bolt 1/2" x 1-1/2" 4 2 PUR1261 Nut 1/2" Nylock 5 2 PUR1249 #3 Hair Pin 6 2 PUR1209 Clevis Pin.375 x 1.375 Yellow Zinc 7 4 CYC4107 Spacer 8 8 PUR1274 Flange Nut 5/16" Nylock 9 2 PUR1123 1/4" x 2" Bolt 10 2 PUR1264 Nut 1/4" Flange Nylock 11 2 PUR2145 1 1/4" P-Clamp 12 2 PUR1848 Mount Bracket Spacer 1-1/4" 13 4 PUR1419 U-Bolt 5/16" x 1-1/4" x 2" 14 4 PUR1420 5/16" x 1-1/4" x 2-3/4" SQ U-Bolt 15 4 PUR2365 U-Bolt 5/16" x 1-3/8" x 2-7/16"
Installation 1. Remove the bottom skid plate from the ATV if equipped. 2. Attach mount straps (Item 2) to ATV frame rails using the supplied U-bolts (Items 13, 14, and 15) as shown below. Use the appropriate size round U-bolts for round frame rails and use the square U-bolts for square frame rails. The U-bolts can be attached to frame members running front to back (see 2A), left to right (see 2B), or a combination of both. Do not fully tighten the U-bolts at this time. Note: exact placement of mount straps and U-bolts will vary among ATVs. 2A. 3 2 8 7 13 14 Spacer (Item 7) may not be needed on all 15 applications. 3
2B. Spacer (Item 7) may not be needed on all applications. 2 3 8 7 13 14 15 2C. 3 34.00 4 Carriage bolts (Item 3) should be approximately 34" back from the front of the front tires.
3. Install the mount weldment (Item 1) to the mount straps (Item 2) as shown below and tighten all U-bolts at this time. Item 1 should be centered left to right on ATV. Cutout can be oriented towards front or rear of ATV to add clearance for drain plug if needed. 4 1 5
4. Some ATV models have the front inner fenders attached to the bottom skid plate which was removed in step 1. These inner fenders will need to be re-fastened to the ATV frame using a P-clamp and spacer (Item 11 and 12) as shown below: Inner fender 10 9 12 11 6
5. Attach the push tube (Model No. 15-0001, sold separately) to the ALLMount as shown below: 6 5 Attach here, front or back. If using Quick Attach (Model No. 10-0005), use front tabs only. Push Tube (Model No. 15-0001) 6. Check for clearance between the plow and front tires with the plow angled to the left and right. If interference is found, it may be necessary to move the plow mount towards the front of the vehicle. If using a manual lift, move the lift handle through the entire range of motion while checking for interference. The location of the plow mount may need to be adjusted to prevent interference. 7
1701 38TH AVE W PO BOX 257 SPENCER, IA 51301 PHONE: 712-262-4191 FAX: 712-262-0248 SERVICE: 800-841-2222 E-MAIL: ccac@cyclecountry.com www.cyclecountry.com ONE YEAR LIMITED WARRANTY For the period of one year from the purchase date Cycle Country Accessories Corporation will replace for the original purchaser, free of charge, any part or parts, when found, upon examination by Cycle Country Accessories Corporation, to be defective in material, workmanship, or both. All transportation cost incurred by the purchaser in submitting the material to Cycle Country Accessories Corporation for replacement under this warranty must be borne by the purchaser. If Cycle Country Accessories Corporation determines that the product must be returned to the factory for credit please call 1-800-841-2222 for an RMA number and shipping instructions. The warranty does not apply to parts that have been damaged by accident, alteration, abuse, improper lubrication, normal wear, or other causes beyond Cycle Country Accessories Corporation s control. Products such as engines, electric motors, and actuators may carry an original manufacturer s warranty. Please call Cycle Country Accessories Corporation for information. 8