FS Uno. Mounting InstructionS FS UNO

Mounting InstructionS FS UNO FS Uno The Schletter FS Uno solar mounting system for ground mount photovoltaic (PV) installation is specifically designed to meet or exceed applicable I, SE, and UL standards. Features onforms to UL 70 ertified to UL/OR Std 70 Electrically bonded unit 0 mp series fuse rating Pre-assembled components Fully integrated and modular components Wind tunnel tested Includes grounding module clamps The FS Uno is capable of accommodating nearly any framed PV module in portrait or landscape orientation. Each FS Uno is custom designed to meet specific structural load requirements. Included in the FS Uno are clamps specifically designed to secure and bond the frame of a PV module. In turn, the components and assemblies that comprise an FS Uno form an electrically bonded unit. While individual components and structural sections will vary between designs, the primary assemblies and installation methods will remain the same. uring installation, fully assemble the system before securing bolts to the final torque. The following is a guide to properly install an FS Uno in order to meet design and test standards. 7 6 Key omponents. Post. Steel head. Strut. -Rail (girder). Retainer plate 6. Z-Rail (purlin) 7. RapidK TM module clamp I00 The FS Uno is evaluated for electrical bonding only. The FS Uno meets all I and SE requirements for structural loading; it was not evaluated for loading under UL 70. FS Uno is not to be used in corrosive atmospheres. Maximum number of modules shall not exceed maximum system voltage ³ Individual parts and components will vary from system-to-system. Please reference system specific drawings. This racking system may be used to ground and/or mount a PV module complying with UL70 only when the specific module has been evaluated for grounding and/or mounting in compliance with the included manual. Installer is responsible for verifying that system meets applicable NE and S standards. Schletter Inc. Updated 0/07 V Subject to change without notice /

Mounting InstructionS FS UNO Installation Tools String line with wood line blocks for foundation post installation Permanent marker Tape measure Rubber mallet for wedge Two () foot carpenter s square for girder-topurlin connection Torpedo level or protractor Wrench and/or socket for all bolted connections Torque wrench Ratchet and/or rechargeable power drill Hex head wrench for standard clamps 7 mm 9 mm Torx bit (TX0) for RapidK TM module clamps 6 mm TX0 / Schletter Inc. Updated 0/07 V Subject to change without notice

FS UNO Mounting InstructionS Foundation Post Installation. Survey Proposed Site Review final drawing. rawing will include information vital to the proper installation of the foundation posts such as the embedment depth, post-to-post spacing, and installation tolerances. Please note: Schletter does not provide construction layouts. inches For longer racks, intermediate stakes may be required. Posts are installed vertically. Tolerance Installation tolerances: Lateral post placement is ±.0 Total Lateral deviation of posts within an array is ±.0 Post height variation tolerance ±0.0 Maximum Maximum Post verticality tolerance <.0 in all directions Post rotational tolerance <±.0 Embedment depth E-W slope For East-West slopes greater than contact your Schletter representative. ±. ± Rotation Elevation difference between adjacent post Lateral cantilever Support distance Schletter Inc. Updated 0/07 V Subject to change without notice /

Mounting InstructionS FS UNO. Post Installation Position each post at respective installation locations based on the completed stake-out (use a forklift). Position the hydraulic ram (GYK) at the installation location and lift the post into position beneath the ram head. Level hammer using bubble level on hydraulic ram. Level mast of hydraulic ram. Level post using a torpedo level. dvance the post approximately two feet into the subsurface then re-check level. dvance the post to the embedment depth as shown on the final drawing. Position string lines: bottom string line is used for correct placement of post; top string line indicates the correct embedment depth: string is run from the top of the first post to the top of the last post. When installing subsequent posts, ram until the hammer head touches the top string line. Mark each post location using soil nails with flagging Position posts on marked locations (use a forklift) Ram two posts at opposite ends of array for string line Use string line as guide to determine correct placement and depth of posts Position hydraulic ram and lift post into position beneath ram head Hammer head touching top string line indicates correct depth is reached / Schletter Inc. Updated 0/07 V Subject to change without notice

FS UNO Mounting InstructionS Mounting the Individual ssembly Groups. Install of Optional Post Splice Verify torque on all bolts. Splices are used to extend the length of a post. Splice location will vary depending on project. onsult project specific drawings.. ttach Steel Head Once the head assembly is aligned, verify the torque of the bolts. Head piece attaches to inside right of the post. Install shim plates between post and splice tubing using / bolts, nuts, and washers (front view of post) lign steel head to the inner side of the post and fasten using M bolts, and nuts (front view of post) Mounted head assembly with multiple holes for adjustment flexibility (rear view of post). Mount Girders Steel head has multiple bolt holes to allow for adjustment to ensure that specified the tilt angle and clearance tolerances are maintained. o not fully tighten the bolt on the steel head. The connector must be loose for mounting the strut. Feed the M bolts through the pre-punched hole in the girder and tighten loosely with nut and washer to the steel head Schletter Inc. Updated 0/07 V Subject to change without notice /

Mounting InstructionS FS UNO. Install Strut ttach strut to girder and post with provided M hardware. The strut must be slotted into the open side of post. Strut to girder connection with M hardware Once all connections are in place, tighten bolts according to torque specifications.. Install Overcurrent Protection evice (grounding) Shares bolt that connects strut to post. Remove serrated flange and install grounding lug, torque to specification. ccomodates stranded or solid copper wire ( gauge to gauge). Must use bare copper wire to connect to the grounding lug. If using insulated grounding wire, remove at least two inches of insulation to expose copper wire. Install one end of strut to connector on girder and the other end to post, secure connections but do not tighten Strut to post connection with M hardware 6. Mount Purlins Z-Rail (purlin) must be mounted at a 90 angle to the girder. The distances between purlins must be observed as specified in the project drawing. Use rubber mallet to drive in the wedge. Retainer plate has slotted holes for adjustment to ensure that specified tilt angle and clearance tolerances are maintained. Loosen or remove top portion of grounding lug and insert grounding wire into appropriate groove Insert purlins into pre-assembled retainer plates Wedge Grounding wire must extend through grounding lug by at least / Hammer in the wedge 6 / Schletter Inc. Updated 0/07 V Subject to change without notice

FS UNO Mounting InstructionS 7. Splice onnection Side view Mount splice on the front side of the purlin. onsult system specific drawings for splice locations. Torque to specification. Secure splice connection with M bolt and washer, and M nut 8. Listing Requirement IMPORTNT! Listing requires that every girder be labeled. If girder has no label, contact your Schletter representative. Label should appear on girder. Schletter Inc. Updated 0/07 V Subject to change without notice 7 /

Mounting InstructionS FS UNO Grounding Path iagram Grounding lamp Purlin (Z-Rail) Retainer Plate Module Frame Purlin Splice Steel Head Post Strut 8 / Schletter Inc. Updated 0/07 V Subject to change without notice

ll rights reserved. Reproduction of any kind only with the express, written consent of the o: Schletter Inc. RETION TE: HEKE TE: ll rights reserved. Reproduction of any kind only with the express, written consent of the o: Schletter Inc. ll rights reserved. Reproduction of RETION any kind TE: only with the express, written consent of the o: Schletter Inc. USTOMER: RETION TE: HEKE TE: ll rights reserved. Reproduction of any kind only with the express, written consent of the o: Schletter Inc. MFG PPROVL TE: ll rights reserved. HEKE TE: Reproduction of any kind only with the express, written consent of the o: Schletter Inc. RETION TE: RETION USTOMER: TE: ll rights reserved. Reproduction of any kind only with the express, written consent of the o: Schletter Inc. USTOMER: ENG PPROVL TE: HEKE TE: HEKE MFG PPROVL TE: TE: RETION TE: SSEMLY NUMER SUONTRTOR: MFG PPROVL TE: USTOMER: USTOMER: HEKE TE: ENG PPROVL TE: ll rights reserved. Reproduction of any kind only with the express, written consent of the o: Schletter Inc. ENG PPROVL TE: MFG PPROVL TE: MFG PPROVL TE: USTOMER: SSEMLY NUMER RETION TE: SSEMLY NUMER ENG SUONTRTOR: PPROVL TE: MFG PPROVL TE: ENG PPROVL TE: SUONTRTOR: SSEMLY NUMER SSEMLY NUMER SUONTRTOR: SUONTRTOR: ENG PPROVL TE: SSEMLY NUMER SUONTRTOR: HEKE TE: USTOMER: MFG PPROVL TE: ENG PPROVL TE: SSEMLY NUMER SUONTRTOR: FS UNO Mounting InstructionS Optional ccessories. onding Jumper Electrically bonds adjacent systems forming a continuous ground path. onnects directly to purlin. vailable in 6-inch to 8-inch lengths. Minimum length for FS Uno is inches. vailable in M0 and M sizes. Install bonding jumper on pre-punched holes at end of purlin using M bolt and washer, and M nut Used for expansion joints or other breaks in racking system.. able Management If cable management was ordered with the system, place before installing modules. WITH of 9.0 OMINER OX WITH of WITH of OMINER 9.0 OMINEROX OX WITH WITH of of OMINER OMINER OX OX WITH of OMINER OX 9.0 9.0 9.0 9.0 WITH of OMINER OX 7 9 6 9.0 7 9 6 7 9 6 7 9 6 7 9 6 7 9 6 ombiner box mount is installed against exterior end of foundation post as shown in image (combiner box not included). 8 0 8 8 0 0 8 8 0 0 0 8 0 FRONT VIEW SIE VIEW SSEMLY VIEW SLE : 0 SLE : 0 SLE : 6 FRONT VIEW SIE VIEW SSEMLY VIEW FRONT VIEW SLE : 0 SIE VIEW SLE : 0 SSEMLY SLE VIEW : 6 SLE : 0 SLE : 0 SLE : 6 FRONT VIEW SIE VIEW SSEMLY VIEW SLE FRONT : 0 VIEW SLE SIE : 0 ISSUE Y: SHLETTER IN. - PROPRIETRY N ONFIENTIL VIEW NOTE: SLE SSEMLY : 6 VIEW PRTS LIST SLE : 0 SLE :. 0 MXIMUM OMINER OX PLUS SLE : 6 RWN Y: ITEM QTY PRT NUMER ESRIPTION MTERIL MSS RT PRT #: kg/m or kg/sq m: TOLERNES: MTERIL: illon.hurley 8//0 ISSUE Y: SHLETTER IN. - PROPRIETRY N ONFIENTILONTENTS WEIGHT = 00 NOTE: lbs. PER KIT 008-000 Post, 8, ustom, Galvanized SE J0 PRTS LIST HEKE: ISSUE Y: SHLETTER IN. WEIGHT: - PROPRIETRY FRONT N VIEW ONFIENTIL. PRTS SIE LIST VIEW NOTE: REFLETS. MXIMUM KITS, S OMINER OX 00-00 PLUS Rail, N0, ustom ITEM QTY PRT NUMER SSEMLY VIEW RWN Y: PRTS LIST 60-T OL PRT # : ESRIPTION MTERIL MSS RT PRT SLE #: : 0 kg/m or kg/sq m: TOLERNES: SHOWN MTERIL: illon.hurley 8//0 SLE OVE :. 0 MXIMUM ONTENTS OMINER WEIGHT OX = 00 PLUS lbs. 000009- PER KIT ITEM ngle, PRT 0x0, NUMER T=, L=00, Slots 008-000 SLE xmm Post, 8, ustom, : 6 60-T 0.7 Galvanized MTERIL kg STTUS: RWN Y: TITLE / PROJET ISSUE Y: / USTOMER: QTY ESRIPTION SE J0 MSS RT SHLETTER PRT #: IN. PROPRIETRY kg/m or kg/sq N m: ONFIENTIL TOLERNES: MTERIL: HEKE: ISSUE Y: SHLETTER IN. - PROPRIETRY N ONFIENTIL WEIGHT: NOTE:. PRTS LIST REFLETS illon.hurley 8//0 ONTENTS WEIGHT = 00 lbs. PER KIT 90-0000 KITS, S Threaded 008-000 Rod, /8"-6 00-00 Post, UN, 8, 0 ustom, SS, Grade Rail, N0, Galvanized 8, L=00mm PRTS 0 SS LIST 0.09 ustom PRTS LIST SE kg WorkInProgress J0 60-T MFG: 000000-000 OL PRT # : TORQUE: HEKE: RWN Y: ITEM QTY PRT NUMER ESRIPTION MTERIL MSS RT PRT #: WEIGHT:. PRTS SHOWN. LIST MXIMUM REFLETS OVEOMINER KITS, 8 OX S 99-00 PLUS Nut, ISSUE Y: SHLETTER IN. - PROPRIETRY kg/m or kg/sq N m: ONFIENTIL TOLERNES: MTERIL: illon.hurley 8//0 NOTE: ITEM 00-00 Flange, Serrated, QTY 000009- PRT Rail, /8"-6 NUMER N0, UN, ustom 6 SS 6 SS 0.0 kg ngle, 0x0, T=, L=00, ESRIPTION Slots xmm 60-T 60-T MTERIL 0.7 MSS kg RWN Y: RT PRT #: kg/m or kg/sq m: STTUS: OL PRT TITLE # : / PROJET / USTOMER: TOLERNES: M6 N /" OLT MTERIL: TORQUE SHOWN IS OVE 6 N-M (. FT-LS) 008-000 Post, 8, ustom, Galvanized PRTS LIST SE J0 illon.hurley 8//0 ONTENTS WEIGHT = 600lbs. 999-6 PER KIT Nut, 000009- Square, /8" - 6 HEKE: WEIGHT:. MXIMUM OMINER OX PLUS 90-0000 008-000 ngle, UN, SME-8.., 0x0, Threaded Post, T=, 8, L=00, 6 SS ustom, Rod, /8"-6 Slots Galvanized xmm 6 SS 0.0 UN, 0 SS, Grade 8, 60-T kg L=00mm 0 SE SS J0 0.09 kg WorkInProgress ssembly irections, ombiner ox Mount, M0 M8 N /6" OLT TORQUE IS N-M (0. FT-LS) 0.7 kg PPROVE: RWN Y: 00-00 ITEM QTY PRT Rail, NUMER N0, ustom ESRIPTION 60-T MTERIL MSS HEKE: MFG: 000000-000 STTUS: TITLE / PROJET / USTOMER: 7 99-00 OL PRT RT PRT #: WEIGHT: kg/m or kg/sq m: TOLERNES: MTERIL: TORQUE:. PRTS LIST REFLETS KITS, S Nut, 90-0000 Square, M0, IN illon.hurley 8//0 ONTENTS WEIGHT = 00 lbs. PER KIT 8 99-00 00-00 Threaded 7, 6 Rod, SS Nut, Rail, /8"-6 Flange, N0, ustom UN, Serrated, 0 SS, /8"-6 Grade 6 SS 0.0 kg UN, 8, 6 L=00mm SS 0 SS 6 60-T SS 0.09 kg WorkInProgress # REVISION Y TE M0 N /8" OLT TORQUE ttach IS 0 N-M ( FT-LS) combiner box foundation post 0.0 kg OL PRT # : SHOWN M6 N /" OVE OLT TORQUE IS 6 N-M (. FT-LS) MFG: 000000-000 8 99-00 Washer, 8 99-00 M0, IN 000009-, 0 SS 008-000 ngle, 0x0, Post, T=, 8, L=00, ustom, 6 Slots Galvanized SS xmm 0.00 kg SIZE: ROWN: PRT NUMER: M N /" OLT TORQUE: IS 0 N-M (7 FT-LS) 60-T SE J0 0.7 TITLE PROJET USTOMER: STTUS: HEKE: WEIGHT:. PRTS LIST REFLETS KITS, S 6 000009-999-6 Nut, Flange, Nut, ngle, Serrated, Square, 0x0, /8"-6 T=, - UN, 6 L=00, UN, 6 SME-8.., Slots SS xmm6 6 SS SS 6 60-T SS 0.0 kg 0.0 0.7 kg 90-0000 00-00 Threaded Rod, Rail, /8"-6 N0, ustom UN, 0 SS, Grade 8, L=00mm 0 60-T0.09 STTUS: 000000-000 ssembly PPROVE: WorkInProgress TITLE / PROJET ISSUE irections, Y: ombiner / USTOMER: SHLETTER ox Mount, IN. - M0 PROPRIETRY M6 N /8" N OLT ONFIENTIL TORQUE M6 N IS /" M8 OLT N-M N TORQUE (89 /6" FT-LS) OLT IS 6 TORQUE N-M (. 9 FT-LS) NOTE: N-M 900-00 (0. FT-LS) 6 KlickIn, 999-6 M0 MFG: 000000-000 OL PRT # : TORQUE: SHOWN OVE 7 90-0000 99-00 Nut, Square, Threaded Nut, /8" Square, - 6 Rod, UN, M0, /8"-6 SME-8.., Polyamide IN 7, UN, 6 0 6 SS SS, SS (Nylon) 0.00 Grade 8, 6 L=00mm SS kg 0 6 SS 0.09 0.0 kg WorkInProgress # REVISION Y TE M0 N /8" OLT TORQUE IS 0 N-M ( FT-LS) PRTS LIST 0.0 kg ssembly irections, ombiner ox Mount, M0 M0 N /" OLT TORQUE M8 N IS /6" OLT N-M (80 TORQUE FT-LS) IS N-M 0 (0. FT-LS). 960-00 MXIMUM 99-00 000009- Nut, Flange, ngle, Serrated, 0x0, /8"-6 T=, L=00, 6 SS Slots xmm 60-T0.0 0.7 kg MFG: TITLE / PROJET / USTOMER: STTUS: 000000-000 TORQUE: 8 8 99-00 99-00 Nut, Washer, Flange, M0, Serrated, IN, /8"-6 0 SSUN, 6 SS 6 SS 0.0 0.00 kg SIZE: ROWN: PRT NUMER: M N /" OLT TORQUE IS 0 N-M (7 FT-LS) 7 OMINER Screw, 99-00 Hex Head, OX M0x0mm, PLUS IN 9, 0 SS 0 SS 0.0 kg PPROVE: SLE: S SHOWN RWN Y: RE: SHEET: OF Nut, Square, M0, ITEM IN QTY 7, PRT 6 SS NUMER 6 SS ESRIPTION 0.0 kg MTERIL RT PRT # REVISION #: Y TE kg/m or kg/sq M0 m: N /8" TOLERNES: M6 OLT N TORQUE /" OLT TORQUE IS N-M (. FT-LS) 999-6 90-0000 Nut, Square, Threaded /8" 6 UN, Rod, /8"-6 SME-8.., UN, 06 SS, SS Grade 8, 6 L=00mm SS 0 SS 0.0 0.09 kg WorkInProgress M6 /" IS 6 N-M (. 9 ssembly irections, ombiner 000000-000 M6 N /8" OLT MTERIL: IS 0 N-M ( FT-LS) illon.hurley 8//0 TORQUE IS ONTENTS N-M (89 FT-LS) WEIGHT = ox Mount, M0 M8 N /6" OLT TORQUE IS N-M (0. FT-LS) 600 lbs. 900-00 999-6 PER KIT Nut, KlickIn, Square, M0 /8" 008-000 - 6 UN, SME-8.., Post, 8, ustom, 6 SSGalvanized 6 Polyamide SS (Nylon) 0.0 0.00 kg 8 99-00 Washer, M0, IN, 0 SS 6 SS 0.00 kg SIZE: ROWN: PRT NUMER: M N /" OLT TORQUE IS 0 N-M (7 FT-LS) SE J0 PPROVE: MFG: ssembly irections, 000000-000 ombiner ox Mount, M0 M0 M8 N /6" TORQUE: /" OLT TORQUE IS N-M (0. (80 FT-LS) 99-00 8 99-00 Nut, Square, Nut, M0, Flange, IN 7, Serrated, 6 SS/8"-6 UN, 6 SS 6 6 SS 0.0 0.0 kg PPROVE: HEKE: 000000-000 REVISION TE M0 N /8" M6 OLT N TORQUE /" OLT IS TORQUE 0 N-M ( IS 6 FT-LS) 0 7 960-00 99-00 Screw, Nut, Square, Hex Head, M0, 00-00 M0x0mm, IN 7, 6 IN SS Rail, 9, N0, 0 ustom SS 0 6 SS 0.0 0.0 kg 60-T SLE: S SHOWN RE: SHEET: # REVISION WEIGHT: M6 N /8" OLT IS N-M (89 FT-LS). PRTS LIST 9 REFLETS 900-00 KITS, KlickIn, S M0 Polyamide (Nylon) 0.00 kg OF Y TE M0 N /8" OLT TORQUE IS 0 N-M ( FT-LS) N-M (. FT-LS) 99-00 Washer, M0, IN, 0 SS 6 SS 0.00 kg SIZE: ROWN: PRT NUMER: OL PRT # : M0 N /" M OLT N TORQUE /" OLT IS TORQUE N-M (80 IS 0 N-M (7 FT-LS) 6 999-6 Nut, Square, /8" - 6 UN, SME-8.., 6 SS 6 SS 0.0 kg ssembly irections, ombiner ox Mount, M0 SHOWN FT-LS) OVE 0 960-00 M8 N /6" OLT TORQUE IS N-M (0. FT-LS) 8 99-00 Screw, Hex Washer, Head, M0, IN, 0 SS 6 SS 0.00 kg PPROVE: SIZE: ROWN: PRT NUMER: M N /" OLT TORQUE IS 0 N-M (7 FT-LS) 000000-000 M6 N /8" OLT TORQUE IS N-M (89 FT-LS) M0x0mm, 000009- IN 9, 0 ngle, SS 0x0, T=, 0 L=00, SS 900-00 7 99-00 KlickIn, M0Nut, Square, M0, IN 7, 6 SS Polyamide Slots xmm 0.0 kg 60-T TITLE / PROJET / USTOMER: (Nylon) 6 SS 0.00 kg 0.0 kg STTUS: SLE: S SHOWN RE: SHEET: OF 000000-000 # REVISION Y TE M6 N /8" M0 OLT N TORQUE /8" OLT IS TORQUE N-M (89 IS 0 FT-LS) N-M ( FT-LS) 9 900-00 KlickIn, M0 90-0000 Threaded Rod, /8"-6 UN, Polyamide 0 SS, Grade (Nylon) 8, 0.00 L=00mm kg 0 SS WorkInProgress M0 N /" OLT TORQUE IS N-M (80 FT-LS) 0 960-00 8 99-00 Screw, Hex Head, Washer, M0x0mm, M0, IN, IN 9, 0 SS 0 SS 0 SS 6 SS 0.0 kg 0.00 kg SLE: S SIZE: SHOWN ROWN: RE: PRT NUMER: M0 N /" M OLT N TORQUE /" OLT IS N-M (80 IS 0 FT-LS) N-M (7 FT-LS) MFG: 000000-000 SHEET: OF TORQUE: 0 960-00 Screw, Hex 8Head, 99-00 M0x0mm, IN Nut, 9, Flange, 0 SS Serrated, /8"-6 0 UN, SS 6 SS 0.0 kg 6 SS SLE: S SHOWN RE: 9 900-00 KlickIn, M0 Polyamide (Nylon) 0.00 kg 000000-000 SHEET: OF M6 N /8" OLT TORQUE IS N-M (89 FT-LS) M6 N /" OLT TORQUE IS M0 N /" OLT TORQUE IS N-M (80 FT-LS) 6 N-M (. FT-LS) 6 999-6 Nut, Square, /8" - 6 UN, SME-8.., 6 SS 6 SS ssembly irections, ombiner ox Mount, M0 M8 N /6" OLT TORQUE IS N-M 0(0. FT-LS) 960-00 Screw, Hex Head, M0x0mm, IN 9, 0 SS 0 SS 0.0 kg PPROVE: SLE: S SHOWN RE: SHEET: OF 7 99-00 Nut, Square, M0, IN 7, 6 SS 6 SS # REVISION Y TE M0 N /8" OLT TORQUE IS 0 N-M ( FT-LS) 8 99-00 Washer, M0, IN, 0 SS 6 SS SIZE: ROWN: PRT NUMER: M N /" OLT TORQUE IS 0 N-M (7 FT-LS) 000000-000 M6 N /8" OLT TORQUE IS N-M (89 FT-LS) 9 900-00 KlickIn, M0 Polyamide (Nylon) M0 N /" OLT TORQUE IS N-M (80 FT-LS) 0 960-00 Screw, Hex Head, M0x0mm, IN 9, 0 SS 0 SS SLE: S SHOWN RE: SHEET: OF able Tie and Edge lip (90-00) MSS 0.7 kg 0.09 kg 0.0 kg 0.0 kg 0.0 kg 0.00 kg 0.00 kg 0.0 kg Schletter Inc. Updated 0/07 V Subject to change without notice 9 /

Mounting InstructionS FS UNO Module Mounting. Position Modules 0 mm Purlins are positioned according to module dimensions. End clamps are positioned approximately 0 mm from the end of the purlin. Position end clamps approximately 0 mm from end of purlin Modules are positioned on the purlins according to specified dimensions. Secure Modules Verify that the module clamp is fully engaged on the purlin and that the module clamp is aligned with the module frame. Only for modules mounted in portrait orientation. When mounting modules, please observe the clamping points specified by module manufacturer. Torque clamp bolts to 0. ft lbs. Use of impact driver is not recommended. Modules are secured to the purlins mm max.. mm maximum middle clamp to module offset mm max. llowable gaps between modules 0 / Schletter Inc. Updated 0/07 V Subject to change without notice

FS UNO Mounting InstructionS Optional Mounting onfigurations. Rail Sharing Method. Position Modules Purlins are positioned according to module dimensions. Position and secure clamp adapter on purlin; refer to system specific drawings to locate connection points. Snap clamp adapter into place as shown on image Secure clamp adapter with self-drilling screw End clamps are positioned approximately 0 mm from the end of the purlin. 0 mm. Landscape. Position Modules Position and secure clamp adapter on purlin; refer to system specific drawings to locate connection points. Position end clamps approximately 0 mm from end of purlin Modules positioned using rail sharing method Modules positioned in landscape orientation. Secure Modules Verify that the module clamp is fully engaged on the clamp adapter and is aligned with the module frame. When mounting modules, please observe the clamping points specified by module manufacturer. Torque clamp bolts to 0. ft lbs. Use of impact driver is not recommended. Modules are positioned on purlins in landscape according to specified dimensions If adjustable end clamps are provided, slide attachment on to desired height.. mm maximum middle clamp to module offset Schletter Inc. Updated 0/07 V Subject to change without notice /

Mounting InstructionS FS UNO Torque Specifications and Tolerances Systems are specifically designed for each project. Please reference the specific project drawing for allowable tolerances and recommended torque for each size of bolt used in the system. In the event of deviation from approved drawings, contact Schletter immediately. Torx olt for RapidK Module lamps N-M 0. FT-LS M6 and / olt 6 N-M. FT-LS M8 and /6 olt N-M 0. FT-LS M0 and /8 olt 0 N-M FT-LS M and / olt 0 N-M 7 FT-LS M6 and /8 olt N-M 89 FT-LS M0 and / olt N-M 80 FT-LS Note: Recommended speed for installation of self-drilling / diameter is 00-800 RPMS. Equipment Grounding Many PV installations contain more than one mounting system. Such cases call for electrically bonding each of the different manufacturers systems. Since individual racks are fully bonded units it is only necessary to connect individual racks together from one single point to another single point. 6 Only use stainless steel hardware when connecting harnesses or jumpers to the mounting system. Take care to prevent copper wires from directly contacting aluminum surfaces as this will cause corrosion. For this purpose, Schletter offers a bonding jumper (see page 9). The PV INSTLLER of Schletter s electrically bonded FS Uno must provide the components necessary for the final connections to the grounding electrode system. Typically the installation will incorporate a grounding electrode (ground rod), appropriately sized copper wire, rated wire connectors, and grounding lugs which are rated for this purpose. The PV INSTLLER must follow all manufacturers installation literature. Installation must comply with all applicable NE/S sections including but not limited to; NE 0 (Grounding and onding), NE 690 (Solar Photovoltaic Systems), S. (Safety Standard for Electrical Installations), and all other applicable state, and local electrical code requirements. PV INSTLLER shall be fully responsible for all connections between Schletter s bonded FS Uno and PV grounding electrode system. Equipment grounding conductors shall be no less than WG (copper) or WG (aluminum). Equipment grounding conductors can be connected to any exposed metallic portion of rack system provided that: a. connection area is sufficiently sized b. dissimilar metals are not in direct contact c. connection does not interfere with other components d. connection is protected from damage alculation for overcurrent protection device including but not limited to spacing and wire size is the responsibility of the installer. 6 Schletter recommends two bonding jumpers to connect separate systems for redundancy. / Schletter Inc. Updated 0/07 V Subject to change without notice

FS UNO Mounting InstructionS Maintenance Yearly inspection of system should be conducted to maintain optimal performance. Visually inspect for signs of damage, wear, corrosion, or movement. Replace any affected components immediately. heck for loose wiring heck mechanical details of the structure: -t least % of bolted connections must be checked using a calibrated torque wrench. The torque wrench must have a display or be a click type torque wrench. -Torque wrench should be set at 0% of the intended tightening torque. heck is successful if the bolt cannot be loosened. -If >0% of the checked bolted connections are loose, the check has to be increased by a factor of five. -If more than 0% of connections are still loose, all bolted connections much be checked. -Tighten to specified torques Requirements per SME 07 and IS WRNING: Risk of death by electric shock Maintenance should only be performed by qualified personnel. Safety Precautions Follow proper installation and safety procedures at all times. Edges of parts may be sharp. Follow proper lifting procedures. For more information on FS Uno, please contact us at: Schletter Inc. 00 ommerce enter rive Shelby, N 80 all: (888) 608-0 Fax: (70) 9-0 info.us@schletter-group.com Schletter anada Inc. 8 evon rive Windsor, ON N8X L all: (9) 96-800 Fax: (9) 96-80 mail.canada@schletter-group.com Torx is a registered trademark of the amcar orp. division of Textron Industries. Schletter Inc. Updated 0/07 V Subject to change without notice /

Mounting InstructionS FS UNO pproved Module Manufacturers onding and Grounding anadian Solar S6X-0 0P S6X-P-FG S6K-P-FG S6K-M S6K-M S6P-P S6P-P-S S6V-M ET Solar ET-M660 8 80 7 70 6 ET-M660 90 8 80 7 70 WW W ET-M67 0 0 0 ET-M67 0 0 WW W ET-P660 6 60 0 ET-P660 70 6 60 WW W ET-P67 0 0 00 ET-P67 0 0 0 WW W Hanwha Q ells Q.PRO FR G G. G. Q.PLUS FR G. Q.PRO G Q.PLUS G Q.PRO L G. Q.PLUS L G. G. Q.PEK-G. G./MX Q.PEK LK G. Q.PEK L G. Heliene Heliene 6 60 7 96M Heliene 6 60 7 96P Hyundai Solar HiS-M0 0 TI HiS-S0 0 0TI HiS-M0 60 6RG HiS-S6 70 7RG Jinko Solar JKM7P-60 JKM0P-7 Eagle 60 7 Eagle PER Eagle lack 60 7 JKM7PP-60-V JKM0PP-7-V JKM70P-60-V JKM0P-7-V Eagle MX JK07 JK07 JKM6PP-60 Kyocera K60 6GX-LF KU60 6 70-6M KU 0-7ZP KU60-6MP LG LGxxxN-G LGxxxNW-G LGxxxS-G LGxxxSW-G LGxxxNK-G LGxxxN- LGxxxNW- LGXXXN- LGXXXS- LGXXXNW- LGXXXSW- RE Solar RE 0 60 6 70PE RE 0 60PE LK RE00 0 0 0PE7 RE6 70 7 80 8TP RE0 0TP7 SolarWorld Sunmodule SW 80 MONO RH Sunmodule SW 0 POLY R6 Sunmodule SW 0 MONO R6 Sunmodule SW 00 POLY RGP Sunmodule Plus SW 80-9 MONO Sunmodule Plus SW 8-00 MONO (-busbar) Sunmodule Plus SW 80-90 MONO LK (-busbar) Sunmodule Plus SW 7-90 MONO LK Sunmodule Pro-Series SW 60 POLY WO Sunmodule Protect SW 7-80 MONO LK Sunmodule SW 0-0-0 XL MONO Talesun TP660 67M TP660 67P TP660 67P(H) T660M T660P Hipro M9+ TP660M Hipro M0+ TP67M PI ZERO TP67M FETHER.0 TP660P Trina TSM-P TSM-P0 TSM-P0.08 TSM-P0.0 TSM-(II) TSM-PEG TSM-PEG.07 TSM-PEG TSM-PEG0.07 Yingli Green Energy YL00 9 90 8 80 7-0b YL90 8 80 7 70-0b L0 0 0-6b YL7P 70P 6P 60P P 0P- 9b YL60P P 0P P 0P-9b YLP 0P P 0P 0P 00P- b / Schletter Inc. Updated 0/07 V Subject to change without notice