INSTLLTION INSTRUTIONS FOR PRT 99-74 PPLITIONS KI orrego 009 99-74 KIT FETURES DIN Radio Provision ISO DIN Radio Provision Double DIN Radio Provision Stacked ISO Mount Units Provision KIT OMPONENTS ) Radio Housing ) ISO Trim Plate ) ISO rackets D) Double DIN Trim Plate E) Double DIN rackets F) Pocket D E F TOOLS REQUIRED: Small Flat lade Screwdriver/ Panel Removal Tool Phillips Screwdriver -800--09 www.metraonline.com OPYRIGHT 008 METR ELETRONIS ORPORTION
99-74 Dash Disassembly TLE OF ONTENTS - KI orrego 009......... Kit ssembly - DIN Radio Provision...................................... - ISO Mount Radio Provision................................ - Double DIN/Stacked ISO Mount Units Provision.................. 4 Final ssembly...........................................5 *Note: Refer also to the instructions included with the aftermarket radio. KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-54-678 for more information and take steps toward a better tomorrow.
99-74 DSH DISSSEMLY Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip and remove the side trim panels. (Figure ) Remove (4) Phillips screws securing the radio and () Phillips screws securing the / vent panel above the radio. (Figure ) KI ORREGO 009 4 Unclip and remove the radio and / vent panel as one piece then unplug the radio and vent panel and separate. (Figure ) ontinue to kit assembly.
99-74 KIT SSEMLY DIN RDIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure ) Slide the aftermarket radio into the cage until it snaps into place. (Figure ) Snap the pocket into the bottom opening of the radio housing. (Figure ) ontinue to final assembly.
99-74 KIT SSEMLY ISO MOUNT RDIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. Mount the ISO rackets to the radio using the screws supplied with the radio. (Figure ) Slide the radio/bracket assembly into the radio housing until it snaps into place. (Figure ) Snap the ISO Trim plate onto the front of the Radio Housing. (Figure ) 4 Snap the pocket into the bottom opening of the radio housing. (Figure D) ontinue to final assembly. D
99-74 KIT SSEMLY DOULE DIN/STKED ISO MOUNT UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. ut and remove the center bar from the radio housing. (Figure ) Snap the Double DIN brackets to the inside edge of the Radio Housing. (Figure ) Slide the Double DIN or stacked ISO mount unit(s) into the bracket/radio housing assembly and secure the unit(s) to the assembly using the screws supplied with the unit(s). (Figure ) 4 Snap the Double DIN Trim plate onto the front of the Radio Housing. (Figure ) ontinue to final assembly. 4
99-74 FINL SSEMLY FINL SSEMLY () Strip wire ends back /" ) Twist ends together ) Solder D) Tape D Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disassembly. FINL WIRING ONNETIONS Make wiring connections using the EI color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit. METR / EI WIRING ODE V Ignition / cc.......... Red V att / Memory......... Yellow Ground.................. lack* Power ntenna............ lue mp Turn-On............. lue / White mp Ground.............. lack / White Illumination.............. Orange Dimmer................. Orange / White Right Front (+)............ Gray Right Front (-)............. Gray/ lack Left Front (+)............. White Left Front (-).............. White / lack Right Rear (+)............ Violet Right Rear (-)............. Violet / lack Left Rear (+)............. Green Left Rear (-).............. Green / lack *NOTE: When a lack wire is not present, ground radio to vehicle chassis. ll colors may not be present on all leads due to manufacturer s specifications. Enjoy your newly installed radio! 5
99-74 INSTRUTIONS -800--09 www.metraonline.com REV. /5/08 OPYRIGHT 008 METR ELETRONIS ORPORTION INST99-74